Thermador PCG364WL Guide d'installation

Installation

INSTRUCTIONS

THERMADOR.COM

Professional Series Rangetops

THERMADOR.COM

Installation

INSTRUCTIONS

Table of Contents (English) ............................................................... 2

Table de Matières (Français) ........................................................... 19

Índice de Materias (Español) ........................................................... 38

Models |

Modèles |

Modelos:

PCG305W

PCG366W

PCG364WD

PCG364WL

PCG486WL

PCG486WD

Professional Series Rangetops

Page. 2

This THERMADOR

®

appliance is made by

BSH Home Appliances Corporation

1901 Main Street, Suite 600

Irvine, CA 92614

Questions?

1-800-735-4328

www.thermador.com

We look forward to hearing from you!

Table of

CONTENTS

Safety ..................................................................................... 3

Important Safety Instructions .......................................... 3

Installation Instructions ........................................................... 3

Planning Information ....................................................... 5

Ventilation Requirements ................................................ 5

Installation Clearances..................................................... 6

Unpacking, Moving, and Setting the Rangetop.............. 11

Gas Requirements and Hookup ...................................... 12

Electrical Requirements and Connection ........................ 14

Low Backguard Installation (optional) ............................. 15

Burner Test ...................................................................... 16

Installer Checklist.................................................................... 18

Final Check List................................................................ 18

Support, Accessories, and Parts ................................back page

Safety

DEFINITIONS

WARNING

This indicates that death or serious injuries may occur as a

result of non-observance of this warning.

CAUTION

This indicates that minor or moderate injuries may occur as a

result of non-observance of this warning.

NOTICE: This indicates that damage to the appliance or

property may occur as a result of non-compliance with this

advisory.

Note: This alerts you to important information and/or tips.

Page. 3

Safety

 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

INSTALLER: Save these Instructions for the Local Gas

Inspector’s use. Please leave these Installation Instructions

with this unit for the owner. Show the owner the location

of the circuit breaker or fuse. Mark it for easy reference.

OWNER: Please retain these instructions for future

reference. Before using your appliance, be sure to read

this manual.

WARNING

If the information in this manual is not

followed exactly, a fire or explosion may

result causing property damage,

personal injury or death.

-- DO NOT store or use gasoline or other

flammable vapors and liquids in the vicinity

of this or any other appliance.

-- WHAT TO DO IF YOU SMELL GAS

• DO NOT try to light any appliance.

• DO NOT touch any electrical switch.

• DO NOT use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call

the fire department.

-- Installation and service must be performed

by a qualified installer, service agency or the

gas supplier.

WARNING

ELECTRICAL SHOCK HAZARD

• Disconnect power before installing or

servicing. Before turning power ON, be sure

that all controls are in the OFF position.

• DO NOT remove connections.

• DO NOT use an extension cord.

• Improper grounding can result in a risk of

electric shock.

• Failure to follow these instructions can result

in death, fire, or electrical shock.

Local codes vary. Installer is responsible for ensuring that

the installation, gas connections, and grounding comply

with all applicable codes. Failure to follow appropriate

local codes and regulations may void the warranty.

The installation of appliances designed for manufactured

(mobile) home installation must conform with the

Manufactured Home Construction and Safety Standard,

Title 24 CFR, Part 3280 [formerly the Federal Standard for

Mobile Home Construction and Safety, Title 24, HUD {Part

280}] or with local codes where applicable.

Examine the appliance after unpacking it. In the event of

transport damage, do not plug it in.

Remove all tape and packaging before using the

appliance. Dispose of packaging in an environmentally-

responsible manner. Never allow children to play with

packaging material.

This appliance must be grounded. Grounding reduces the

risk of electric shock by providing a safe pathway for

electric current in the event of a short circuit.

The appliance, when installed, must be electrically

grounded in accordance with local codes or, in the

absence of local codes, with the National Electrical Code,

NFPA 70 latest edition, or the Canadian Electric Code,

CSA C22.1-02.

DO NOT install this appliance outdoors.

For Massachusetts Installations:

• Installation must be performed by a qualified or

licensed contractor, plumber or gas fitter qualified or

licensed by the state, province or region where this

appliance is being installed.

• Shut-off valve must be a “T” handle gas cock.

• Flexible gas connector must not be longer than 36''

(914 mm).

Verify the type of gas supplied to the location. Ensure that

the appliance is connected to the type of gas for which it

is certified.

This appliance is capable of being safely placed in

operation in the event of a power failure. Only the

standard top burners can be manually lit.

Page. 4

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

Always keep appliance area clear from combustible

materials, gasoline and other flammable vapors and

liquids.

Natural Gas — 6 inch water column. (14.9 mb) min., 14

inch (34.9 mb) maximum

Propane Gas — 11 inch water column. (27.4 mb) min., 14

inch (34.9 mb) maximum

CAUTION

When connecting the unit to propane gas, make

certain the propane gas tank is equipped with its own

high-pressure regulator in addition to the pressure

regulator supplied with the appliance. The maximum

gas pressure to this appliance must not exceed 14.0''

water column (34.9 mb) from the propane gas tank to

the pressure regulator.

This appliance complies with one or more of the following

Standards:

• UL 858, The Standard for the Safety of Household

Electric Ranges

• ANSI Z21.1, The American National Standard for

Household Cooking Gas Appliances

• CAN1-1.1-M81, Domestic Gas Ranges

• CSA C22.2 No. 61, Household Cooking Ranges

Check local building codes for the proper method of

appliance installation. Local codes vary; it is the

responsibility of the installer to ensure installation is in

accordance with these codes. Installation, electrical

connections, and grounding must comply with all

applicable codes.

In the absence of local codes the appliance should be

installed in accordance with the National Electric Code

NFPA 70 current issue and National Gas Code NFPA 54/

ANSI Z223.1 – current issue. In Canada, installation must

be in accordance with the Canadian Electric Code, CSA

C22.1-02 and the CAN 1-B149.1 and .2 – Installation

Codes for Gas Burning Appliances and/or local codes.

State of California Proposition 65 Warning:

WARNING

This product can expose you to chemicals including

vinyl chloride, which is known to the State of California

to cause cancer and birth defects or other

reproductive harm. For more information go to

www.P65Warnings.ca.gov.

REAR CLEARANCE REQUIREMENTS:

• To avoid staining on the back wall, high temperature,

non-porous construction materials suitable for use in a

cooking environment are recommended.

• Models PCG305xx, PRD305xx, and PRD606xx are

suitable for 0'' rear clearance to combustible surfaces.

• All Other Models:

• When using the included Island Trim a minimum

6" (152 mm)* rear clearance is required to a

combustible surface*.

• When installing against a combustible surface, a

T

WTa\PS^a

®

Low Backguard is required for a

0'' rear clearance to the combustible surface. A

Thermador Low Backguard must be purchased

separately.

• A rear clearance to a surface covered in a non-

combustible material (metal, ceramic tile, brick,

marble, or stone)

*'

is 0" when using the included

Island Trim.

*Clearances of less than 6'' (152 mm) should be approved by the

local codes and/or by the local authority having jurisdiction.

' Clearances from non-combustible materials are not part of the

ANSI Z21.1 scope and are not certified by CSA.

WARNING

To avoid possible burn or fire hazard, a backguard

designed specifically for this appliance should be

installed whenever the appliance is used.

WARNING

To eliminate risk of burns or fire caused by reaching

over heated surface units, cabinet storage located

above the surface units should be avoided.

CAUTION

This unit is designed as a cooking appliance. Based on

safety considerations, never use it for warming or

heating a room. Doing so may result in carbon

monoxide poisoning and overheating the appliance.

Page. 5

Installation Instructions

Planning Information

CAUTION

To prevent possible damage to cabinets and cabinet

finishes, use only materials and finishes that will not

discolor or divide into layers. Materials should be able

to withstand temperatures up to 194 °F (90 °C). Heat

and moisture resistant adhesive must be used if the

product is to be installed in laminated cabinetry.

Check with the manufacturer to ensure materials meet

these requirements.

Before using your appliance, be sure to read this manual.

Pay special attention to the

Important Safety Instructions

located at the beginning of the manual.

Any opening in the wall behind the appliance and in the

floor under the appliance shall be sealed.

Tools Needed

• 7/16'' Box wrench

• Level

• T-20 Torx screwdriver

• Protective gloves

• 12'' Adjustable wrench

• Tape measure

• Marking instrument

Items Required

• 3/4'' (19 mm) Flex Line

• Pipe Compound/Tape

IMPORTANT: There is a possibility to discolor the back

wall under certain cooking conditions.

Ventilation Requirements

WARNING

This appliance should not be installed with a

ventilation system that directs air in a downward

direction toward the appliance. This type of

ventilation system may cause ignition and combustion

problems with the appliance resulting in personal

injury, property damage, or unintended operation.

Ventilating systems that direct the air upwards do not

have any restriction.

Refer to the Ventilation Planning Guide for approved

ventilation combinations.

It is strongly recommended that this appliance be installed

in conjunction with a Thermador vent hood. Due to the

high heat capability of this unit, particular attention should

be paid to the hood and duct work installation to assure it

meets local building codes.

Downdraft ventilation should not be used. The Ventilation

Planning Guide indicates the ventilation hood options and

blower capacity guidelines that are recommended for use.

Due to the high heat of the rangetop burners, installing a

microwave oven with a ventilation system over the

rangetop is not recommended on anything other than the

30'' 5–Burner. Refer to OTR manufacturer’s installation

manual for clearances.

Ventilation hoods and blowers are designed for use with

single wall ducting. However, some local building codes or

inspectors may require double wall ducting. Consult local

building codes and/or local agencies before starting to

assure that hood and duct installation will meet local

requirements.

NOTICE: Most range hoods contain combustible

components which must be considered when planning the

installation.

Ventilation Preparation

1. Select Hood and Blower Models:

• For wall installations, the hood width must, at a

minimum, equal the width of the range/rangetop.

Where space permits, a hood larger in width than

the range/rangetop may be desirable for

improved ventilation performance.

• For island installations, the hood width should

overhang the width of the range/rangetop by a

minimum of 3" (76 mm) on each side.

2. Hood Placement:

• For best smoke elimination, the lower edge of the

hood should be installed 30" (762 mm) above the

range cooking surface.

• If the hood contains any combustible materials

(i.e. a wood covering), it must be installed a

minimum of 36" (914 mm) above the cooking

surface.

3. Consider Make-Up Air:

• Due to the high volume of ventilation air, a source

of outside replacement air is recommended. This

is particularly important for tightly sealed and

insulated homes.

• A qualified heating and ventilating contractor

should be consulted.

Page. 6

Installation Clearances

• To ensure professional results, the cabinet and

countertop openings should be prepared by a

qualified cabinet worker.

• The same clearances apply to island installations,

except for the overhead cabinets, which must have a

space wide enough to accept the island hood.

• See the Ventilation Planning Guide for recommended

hood options. Due to the high heat of the burners,

installing a microwave oven with a ventilation system

over the appliance is not recommended on anything

other than the 30'' 5–Burner. Refer to the OTR

manufacturer’s installation manual for clearances.

• The rangetop is designed to hang from the

countertop by its flanges. The countertop however,

must be strong enough to support this rangetop. It

may be necessary to add a supporting cleat along

each side or a 2 x 4 corner brace (see page 10).

Another alternative would be to construct a deck to

set the rangetop on.

• The rangetop can be installed in various positions with

the front either flush or projecting, depending on the

countertop’s depth. See page 11 for alternate

mounting positions.

• The gas and electrical supply must be located in an

area that is accessible without requiring removal of the

rangetop.

• The shaded area behind the appliance indicates an

opportunity to discolor the back wall under certain

cooking conditions.

• There must be a minimum of 5'' (127 mm) side

clearance from the appliance to combustible vertical

surfaces above the 36'' (914 mm) counter height.

• Within the 5'' (127 mm) side clearance to combustible

vertical surfaces above 36'' (91.4 cm), the maximum

wall cabinet depth must be 13'' (330 mm).

• Wall cabinets within this 5'' (127 mm) side clearance

must be 18'' (45.7 cm) above the 36'' (914 mm) high

countertop.

• There is a 36'' (914 mm) minimum clearance required

between the top of the cooking surface and the

bottom of an unprotected cabinet. A 30'' (762 mm)

clearance can be used when the bottom of the wood

or metal cabinet is protected by not less than 1/4''

(6 mm) of a flame retardant material covered with not

less than No. 28 MSG sheet steel, 0.015'' (0.38 mm)

thick stainless steel, 0.024'' (0.61 mm) aluminum, or

0.02'' (0.51 mm) thick copper.

• Establish the centerline of the appliance’s desired

location. It should be the same as the center of the

overhead ventilation hood.

• Cut the openings for the following installations:

• Wall installation, see page 10.

• Island installation, see page 10.

REAR CLEARANCE REQUIREMENTS:

• To avoid staining on the back wall, high temperature,

non-porous construction materials suitable for use in a

cooking environment are recommended.

• Models PCG305xx, PRD305xx, and PRD606xx are

suitable for 0'' rear clearance to combustible surfaces.

• All Other Models:

• When using the included Island Trim a minimum

6" (152 mm)* rear clearance is required to a

combustible surface*.

• When installing against a combustible surface, a

Thermador

®

Low Backguard is required for a 0''

rear clearance to the combustible surface. A

Thermador Low Backguard must be purchased

separately.

• A rear clearance to a surface covered in a non-

combustible material (metal, ceramic tile, brick,

marble, or stone)*

' is 0'' when using the included

Island Trim.

*Clearances of less than 6'' (152 mm) should be approved by the

local codes and/or by the local authority having jurisdiction.

' Clearances from non-combustible materials are not part of the

ANSI Z21.1 scope and are not certified by CSA.

NOTES:

• If a solid side cabinet wall exists on one or both sides,

you will need to notch the front corner of the cabinet

to match the countertop notch and to allow clearance

for the rangetop front (see Detail A, page 10).

• If a supporting deck is used, the sides or bottom of

the cutout may be solid combustible or non-

combustible material. If the bottom is solid, provide a

12'' by 12'' (305 mm x 305 mm) cutout in the left rear

corner of the supporting deck. This will provide

clearance for the gas inlet and power cord.

• Always keep appliance area clean and free from

combustible materials, gasoline and other flammable

vapors and liquids.

• DO NOT obstruct the flow of combustion and

ventilation air to the unit.

Page. 7

Clearance requirements with a Low

Backguard (purchased separately)

' as defined in the “National Fuel Gas Code” (ANSI Z223.1, Current Edition). Clearances from non-combustible materials are not part of the ANSI Z21.1

scope and are not certified by CSA. Clearances of less than 6'' (152 mm) should be approved by the local codes and/or by the local authority having

jurisdiction.

1

8" (457)

1

8" (457)

0

"

0

"

36" or 48"

( 914 or 1,219 )

36" or 48"

( 914 or 1,219 )

13"

(330)

13"

(330)

0

"

0

"

30" (762) –

40" (1016)

30" (762) –

40" (1016)

0

"

0"

5

" (12

7

)

inches (mm)

Page. 8

Clearance requirements with the Island

Trim (included)

' as defined in the “National Fuel Gas Code” (ANSI Z223.1, Current Edition). Clearances from non-combustible materials are not part of the ANSI Z21.1

scope and are not certified by CSA. Clearances of less than 6'' (152 mm) should be approved by the local codes and/or by the local authority having

jurisdiction.

5

"

(12

7

)

1

8"

(457)

1

8"

(457)

30"

(762) –

40"

(1016)

30"

(762) –

40"

(1016)

0"

36" or 4

8"

(914 or 1,219 )

36" or 4

8"

(914 or 1,219 )

13"

(330)

13"

(330)

6" (152)6" (152)

inches (mm)

Page. 9

Clearance requirements with OTR –

PCG305 ONLY

• 30" (762 mm) minimum to non-combustible material

above the Cooking Surface.

* Refer to OTR manufacturer’s installation manual for

clearances.

' as defined in the “National Fuel Gas Code” (ANSI Z223.1, Current Edition). Clearances from non-combustible materials are not part of the ANSI Z21.1

scope and are not certified by CSA. Clearances of less than 6'' (152 mm) should be approved by the local codes and/or by the local authority having

jurisdiction.

1

8" (457)

1

8" (457)

0

"

0

"

30" (762)30" (762)

0

"

0

"

*

30" (762)

*

30" (762)

0

"

0"

5

" (12

7

)

13"

(330)

13"

(330)

inches (mm)

Page. 10

Countertop Cutout

Installing Side Support Cleats (both sides)

Wall Installation with Countertop Backsplash

Counter

sunk

screws

Detail A

B

23

5

/

16

"

(592)

23

5

/

16

"

(592)

D

A

inches (mm)

Island Installation Without Countertop Backsplash

Detail A: Front Face of Cabinet

Detail A

22

13

/16

"

(580)

22

13

/16

"

(580)

¾" (19)

minimum

D

A

inches (mm)

2 x 4 Corner

Support

Corner Notch DetailCorner Notch Detail

C

B

77

11

//

1616

"

(195)

inches (mm)

30'' Rangetop 36'' Rangetop 48'' Rangetop

A 29-15/16'' (760 mm) 35-15/16'' (913 mm) 47-15/16'' (1,218 mm)

B 3/8'' (10 mm) 3/8'' (10 mm) 7/8'' (22 mm)

C

0'' (0 mm) Control panel projecting 1

½'' (38 mm) from base cabinet face.

11/16'' (18 mm) Notch required for standard 24'' (610 mm) deep base cabinet; Control panel projecting 13/16''

(20 mm) from base cabinet face.

D 29-1/8'' (740 mm) 35-1/8'' (892 mm)

46-1/4

'' (1,175 mm)

Page. 11

Gas inlet location

A manual valve must be installed external to the

appliance, in an accessible location from the front, for the

purpose of shutting off the gas supply.

Unpacking, Moving, and

Setting the Rangetop

CAUTION

Proper equipment and adequate manpower

must be used in moving the appliance to avoid

damage and/or personal injury. The unit is heavy

and should be handled accordingly.

Hidden surfaces may have sharp edges. Use

caution when handling the appliance. Failure to

do so may result in property damage or personal

injury.

1. Verify that the appliance is correct for the type of gas

being provided.

2. Remove the outer carton and packing material from

the shipping base. Ensure that you have

all rangetop

components before proceeding.

3. Remove the cooking grates, griddle plate (if

applicable), and burner caps

to reduce the rangetop’s

weight.

Side View of Rangetop

Projecting from Cabinet Front

Installation of rangetop above Thermador warming drawers

Cabinet face for installation with

projecting control panel.

Cabinet face for installation

with flush control panel.

7

5

/

8

"

(194)

7

5

/

8

"

(194)

7

/

8

"

(22)

7

/

8

"

(22)

26¾" (680)26¾" (680)

22½" (573)22½" (573)

½" (12.7)

side flange

½" (12.7)

side flange

inches (mm)

1½"

(38)

Front projects outward 13/16" (20) as

shown from standard 24" deep base.

Notch Depth

11

//

1616

"

(18)

13

/

16

"

(20)

inches (mm)

Plywood support

Install additional

wood support along

front edge of cutout

2¾" (70)

min. between

cutouts

7

5

/

8

"

(194)

7

5

/

8

"

(194)

inches (mm)

Gas Inlet Location 30'' 36'' 48''

From left side to

centerline of gas inlet

6-3/8''

(152 mm)

11" (267 mm)

From rear to centerline of

gas inlet

2¼'' (54 mm)

¾" (19) ex line¾" (19) ex line

½" (12.7) NPT

inches (mm)

Page. 12

4.

Leave protective film

over brushed-metal surfaces, to

protect finish from scratches, until the rangetop is

installed in its final position.

5. Use a 7/16” box wrench to remove the four (4) bolts

from the bottom of the pallet and discard.

6. Attach the backguard, if applicable, before sliding the

appliance into the final installed position.

7. Lift and place the rangetop in the countertop

opening. Be careful not to pinch the power cord or

gas inlet. Care should be used not to scratch the

countertop.

8. Make sure that the power cord is free and hanging

loose.

9. The rangetop must be level for proper performance.

10. Replace the cooking grates, griddle plate, and burner

caps. Ensure that the burner caps are correctly seated

on the burner bases.

Assembling the Grill (not all models)

Refer to “Using the Electric Grill” in the Use and Care

Guide.

Griddle Tilt Adjustment (not all models)

Refer to “Using the Electric Griddle” in the Use and Care

Guide.

Gas Requirements and Hookup

Gas Hook Up

• A manual gas shut-off valve must be installed external

to the appliance, in a location accessible from the

front, for the purpose of shutting off the gas supply.

The supply line must not interfere with the back of the

unit. Make sure the gas supply is turned off at the

manual shut-off valve before connecting the

appliance.

• The installer should inform the owner of the location

of the gas shut-off valve. Make sure all users know

where and how to shut off the gas supply to the

rangetop.

• The gas supply connections shall be made by a

competent technician and in accordance with local

codes or ordinances. In the absence of local codes,

the installation must conform to the National Fuel Gas

Code ANSI Z223.1/NFPA54-current issue or, in

Canada, the Natural Gas and Propane Installation

Code, CSA B149.1.

• The gas supply pressure for checking the regulator

setting shall be at least 1 in. WC (249 Pa) above the

manufacturer's specified manifold pressure.

• Use a ¾'' (19 mm) flex line to connect between the

gas supply and the appliance gas inlet. The gas supply

line connection is located at the left rear of the

appliance. The appliance gas inlet connection is ½''

(12.7 mm) NPT.

• Use caution to avoid crimping the ¾'' (19 mm) flex

line when making bends. Suggested length of flex

line is 48" (1,219 mm); however, please check

local codes for your area's requirements before

installation.

• Use pipe sealing compound or Teflon® tape on the

pipe threads. DO NOT apply sealing compound or

tape to flare fittings. Take care not to apply excessive

pressure when tightening the fittings.

• All installer-supplied parts must conform to applicable

codes.

• Leak testing of the appliance shall be in accordance

with the following instructions.

• Turn on gas and check supply line connections for

leaks using a soap and water solution.

• Bubbles forming indicate a gas leak. Repair all

leaks immediately after finding them.

WARNING

DO NOT use a flame of any kind to check for gas

leaks.

¾" (19) external threads¾" (19) external threads

½" (12.7) internal threads½" (12.7) internal thread

s

{

¾" (19)

Flex line

¾" (19)

Flex line

inches (mm)

Page. 13

High Altitude

This appliance has been tested for operation up to an

altitude of 10,100 ft (3,078 m) elevation above sea level.

If desired, for altitudes above 2,000 feet (610 m) elevation

above sea level, adjustments can be made with a High

Altitude Kit. If flame performance is satisfactory,

adjustment will not be required. It is required that a

Certified Professional make the high altitude adjustments

during installation.

Gas Requirements

Natural Gas Requirements:

• Inlet Connection: 1/2'' NPT internal (Minimum 3/4''

dia. flex line)

• Supply Pressure: 6'' min. to 14'' max. water column

(14.9 to 34.9 mb)

• Manifold Pressure: 5'' water column (12.5 mb)

Propane Gas Requirements:

• Inlet Connection: 1/2'' NPT internal (Minimum 3/4''

dia. flex line)

• Supply Pressure: 11'' min. to 14" max. water column

(27.4 mb to 34.9 mb)

• Manifold Pressure: 10'' water column (24.9 mb)

Rangetops are shipped by the factory to operate on

natural gas. They must be converted for use with propane.

Verify the type of gas being used at the installation site

matches the type of gas used by the appliance.

If the location site requires conversion from natural gas to

propane (LP), contact the dealer where the unit was

purchased or contact Thermador

®

to purchase a

conversion kit. Obey all instructions in this kit for correct

conversion of the gas regulator and settings for the gas

valves. Field conversion must be done by qualified service

personnel only.

WARNING

If a gas conversion kit is used, the kit shall be installed

by a qualified service personnel in accordance with

the manufacturer’s instructions and all applicable

codes and requirements of the authority having

jurisdiction. If the information in the instructions is not

followed exactly, a fire, explosion or production of

carbon monoxide may result causing property

damage, personal injury or loss of life. The qualified

service personnel is responsible for the proper

installation of the kit. The installation is not proper and

complete until the operation of the converted

appliance is checked as specified in the

manufacturer’s instructions supplied with the kit.

CAUTION

The appliance must be isolated from the gas supply

piping system by closing its individual manual shut-off

valve during any pressure testing of the gas supply

piping system at test pressures equal to or less than

1/2 psig (3.5kPa).

The appliance and its individual shut off valve must be

disconnected from the gas supply piping system

during any pressure testing of the system at test

pressures in excess of 1/2 psig (3.5kPa.).

When checking the manifold gas pressure, the inlet

pressure to the regulator should be at least 6.0" W.C.

for natural gas or 11.0" for propane.

DO NOT attempt any adjustment of the pressure

regulator.

CAUTION

Save the orifices removed from the appliance for

future use. When connecting unit to propane gas,

make certain the propane gas tank is equipped with

its own high pressure regulator in addition to the

pressure regulator supplied with the appliance. The

pressure of the gas supplied to the appliance

regulator must not exceed a 14'' water column

(34.9 mb).

Page. 14

Electrical Requirements and

Connection for Gas Units

WARNING

Before installing, turn power OFF at the service panel.

Lock service panel to prevent power from being

turned ON accidentally. Always disconnect appliance

from the electric supply either by disconnecting

power cord or shutting off the breaker at the service

panel before servicing the appliance.

WARNING

This product must be properly grounded.

INSTALLER — show the owner the location of the circuit

breaker. Mark it for easy reference.

Gas Unit Electrical Connection

Electrical Supply Circuit Requirements

The cord supplied with the

gas ranges having an electric

griddle or grill requires a

NEMA 5-20 receptacle. All

other gas units require a

NEMA 5-15 receptacle.

WARNING

Electrical Grounding Instructions

This appliance is equipped with a three-prong

grounding plug for your protection against shock

hazard and should be plugged directly into a properly

grounded receptacle. DO NOT cut or remove the

grounding prong from this plug.

CAUTION

Improper grounding or reverse polarization will cause

malfunction (such as continuous sparking of the

burner igniters). This can damage the appliance and

can create a condition of shock hazard. If the

dedicated circuit is not correctly grounded and

polarized, it is the responsibility and obligation of the

installer and user to have the existing receptacle

changed to a properly dedicated grounded and

polarized receptacle. This must be accomplished in

accordance with all applicable local codes and

ordinances by a qualified electrician. In the absence of

local codes and ordinances, the receptacle

replacement shall be in accordance with the National

Electric Code.

• Before you plug in an electrical cord, be sure all

controls are in the OFF position.

• A neutral supply wire must be provided from the

power source (breaker) because critical range

components, including the surface burner spark

reignition modules, require it to operate safely and

properly.

• All 120 Volt models must be plugged into a mating 3-

Prong, Grounding-Type Receptacle. The receptacle

must be connected to a properly dedicated grounded

and polarized electrical power supply rated at

120VAC, Single Phase, 60Hz.

• Observe all governing codes and ordinances when

grounding. In the absence of these codes or

ordinances observe National Electrical Code ANSI/

NFPA No. 70 current issue, or the relevant Canadian

Electric Code, CSA C22.1-02.

Model Voltage Dedicated Circuit Phase

Pxx305Wx 120 VAC 15 Amps Single

Pxx366Wx 120 VAC 15 Amps Single

Pxx364WDx 120 VAC 20 Amps Single

Pxx364WLx 120 VAC 20 Amps Single

Pxx486WDx 120 VAC 20 Amps Single

Pxx486WLx 120 VAC 20 Amps Single

NEMA 5-15 NEMA 5-20

G

N

• Power cord and receptacle

should protrude no more than

2'' (51 mm) from the rear wall.

NOTE: Plug styles may vary.

2"

(51)

Page. 15

Low Backguard Installation

(optional)

Attach the backguard before sliding the appliance into the

final installed position.

1. Depending on model, remove the 2 or 3 stainless Torx

screws in the front face of the included Island Trim. Lift

up to fully remove the Island Trim.

2. Slide the support brackets of the Low Backguard

between the two rangetop chassis back panels.

3. Secure the back with 8 x 1½'' (38 mm) screws.

4. Secure the front of the Low Backguard to the

rangetop with 2 or 3 x ½'' (12.7 mm) screws.

9½"

(239)

9½"

(239)

Page. 16

Burner Test

Install any loose components, such as burner caps and

grates that may have been removed earlier. Be certain that

burner caps seat properly into the burner bases. Before

testing operation of the appliance, verify that the unit and

the gas supply have been carefully checked for leaks and

that the unit has been connected to the electrical power

supply. Turn the manual gas shut-off valve to the open

position.

Burner Cap Placement

Each cap has a letter (B, D, or F) cast in the underside of

the cap that corresponds to a letter (B, D, or F) cast in the

burner base that is attached to the appliance.

• Place each burner cap on its correct burner base per

its corresponding letter designation. See figure below.

• Place burner cap gently on top of base so that the

prongs of the burner base fit snugly into the groove of

the burner cap.

The burner caps must be properly placed on the burner

bases for the rangetop to function properly. If the burner

cap is not properly placed, one or more of the following

problems may occur:

• Burner flames are too high.

• Flames shoot out of burners.

• Burners do not ignite.

• Burner flames light unevenly.

• Burner emits gas odor.

WARNING

To prevent flare-ups and avoid the creation of harmful

by-products, do not use the rangetop without all

burner caps and all burner grates properly positioned.

WARNING

To prevent burns, do not touch burner caps or grates

while hot. Turn the rangetop off and allow the burners

to cool.

Checking Burner Cap Placement

• Check each burner to make sure there is no gap

between the burner cap and burner base. See figures

below for correct and incorrect burner cap placement

to see examples of the burner cap.

• You may gently try to move the burner caps from side

to side to check if the caps are properly placed on the

burner bases. When properly placed, each burner cap

will rest flat on top of its burner base, and completely

cover the star-shape of the burner base when viewed

from the top as shown in the figures.

Burner Grate Placement

Ensure the burner grates are properly placed on the

rangetop before using the surface burners. The grates are

designed to rest inside the recess on the rangetop.

To install burner grates, place grates flat-side down and

align into the rangetop recess. Grates should rest flush

against each other and against the sides of the recess.

Page. 17

Test Rangetop Burners

Test Burner Ignition. Select a rangetop burner knob. Push

in and turn counterclockwise to HI. The igniter will

produce a clicking sound. Once the air has been purged

from the supply lines, the burner should light within four

(4) seconds.

Test Flame: High Setting. Turn burner on to HI. See

figures below for appropriate flame characteristics. If any

of the rangetop burners continue to burn mostly or

completely yellow, verify that the burner cap is positioned

properly on the burner base, then re-test. If flame

characteristics do not improve, call Thermador service.

Test Flame: Low Setting. Turn burner on to LOW. Verify

that the flame completely surrounds the burner. There

should be a flame at each burner port and there should be

no air gap between the flame and the burner. If any

burners do not carry over, call Thermador service.

The burners that feature XLO

®

, cause the flame to cycle

on and off when the knob is set to the XLO function. This

is normal operation.

Repeat the Ignition and Flame Test procedures described

above for each rangetop burner.

WHEN FLAME IS PROPERLY ADJUSTED:

• There should be a flame at each burner port.

• There should be no air gap between the flame and

burner port.

Call Thermador service if:

• Any of the burners do not light.

• Any of the burners continue to burn yellow.

Flame Characteristics

Yellow Flames:

Further adjustment is

required.

Yellow Tips on Outer Cones:

Normal for LP Gas

Soft Blue Flames:

Normal for Natural Gas

If the flame is completely or mostly yellow, verify that

the regulator is set for the correct fuel. After

adjustment, retest.

Some orange-colored streaking is normal during the

initial start-up.

Allow unit to operate 4-5 minutes and re-evaluate

before making adjustments.

Page. 18

Installer Checklist

Final Checklist

Gas Supply

Electrical

Installer

Operation

To Clean and Protect Exterior Surfaces

• Always wipe in the direction of the stainless steel

grain.

• To condition and protect stainless steel, use the

Thermador Stainless Steel Conditioner, which can be

purchased in the Thermador eShop

(store.thermador.com/us).

• DO NOT allow deposits to remain for long periods of

time.

• DO NOT use ordinary steel wool or steel brushes.

Small bits of steel may adhere to the surface causing

rust.

• DO NOT allow salt solutions, disinfectants, bleaches

or cleaning compounds to remain in contact with

stainless steel for extended periods. Many of these

compounds contain chemicals which could prove

harmful. Rinse with water after exposure and wipe dry

with a clean cloth.

Troubleshooting

See Use and Care Guide for troubleshooting information.

Rangetop correctly positioned in countertop recess.

Specified clearances maintained to cabinet surfaces.

Burner caps positioned properly on burner bases.

All packaging material removed.

Flush Island Trim or Low Backguard attached

according to instructions.

Connection: 1/2'' NPT with a minimum 3/4''

diameter flex line.

If converting from natural to LP gas, refer to LP

Conversion Instructions for details.

Manual gas shut off valve installed in an accessible

location (without requiring removal of appliance).

Unit tested and free of gas leaks.

A dedicated polarized and grounded 120VAC

receptacle with a 15/ 20 AMP over current

protection is required for cord connection.

Write the model number and serial numbers (see

figure below) in the Use and Care Guide. Leave the

USE AND CARE GUIDE and INSTALLATION

INSTRUCTIONS with the owner of the appliance.

Bezels centered on burner knobs, and knobs turn

freely.

Purge air from gas system by operating one of the

burners for several minutes.

Each burner lights satisfactorily, both individually

and with other burners operating.

Burner grates are correctly positioned.

Page. 19

Cet appareil électroménager de THERMADOR

TM

est fait par BSH Home Appliances LtD

6696 Financial Drive, Unit 3

Mississauga, ON L5N 7J6

Des questions?

1-800-735-4328

www.thermador.ca

Nous attendons de vos nouvelles!

Table des

MATIÈRES

Sécurité .................................................................................. 20

Instructions Importants de Sécurité ............................... 20

Consignes d'Installation.......................................................... 23

Renseignements de planification .................................... 23

Exigences en matière de ventilation .............................. 23

Espaces libres pour l’installation ..................................... 24

Déballage et manutention et mise en place................... 30

Exigences pour l'alimentation du gaz et

raccordement .................................................................. 31

Exigences électrique et branchement ........................... 33

Installation de la plaque de protection basse................. 34

Test de brûler ................................................................. 35

Liste de vérification pour l’installateur ................................... 37

Liste de vérification ......................................................... 37

Soutien, pièces, et accessoires.................................page verso

Définitions de

SÉCURITÉ

AVERTISSEMENT

Ceci indique que le non respect de cet avertissement peut

entraîner des blessures graves, voire la mort.

ATTENTION

Ceci indique que le non respect de cet avertissement peut

entraîner des blessures légères ou modérées.

NOTICE : Ceci indique que la non-conformité à cet avis de

sécurité peut entraîner des dégâts à l'appareil ou à la propriété.

Note : Ceci vous avertit que d'importantes informations et/ou

conseils sont fournis.

La page charge ...

Thermador PCG364WL Guide d'installation

Ce manuel convient également à

Thermador PCG364WL Guide d'installation

dans d''autres langues

Documents connexes

Autres documents