Bradley 400 Series Guide d'installation

Installation

P.O. Box 309

Menomonee Falls, WI 53052 USA

800 BRADLEY (800 272 3539)

+1 262 251 6000

bradleycorp.com

HDWT-INSTR-009 Rev K; ECN 17-14-007

Page 1 of 83 3/21/2018

Powder Coated & Stainless Steel Restroom

Partitions

Floor-Mounted with Overhead Brace

Series 400

Cloisons de toilettes en acier inoxydable et

à peinture en poudre

à fixation au sol et barre de tête

Série 400

Divisiones para baños con revestimiento

de polvo y de acero inoxidable para

montaje en el piso con soporte superior

Serie 400

*HDWT-INSTR-009*

For Standard Height

Doors and Panels Only

Pour portes et panneau de

hauteur standard seulement

Solo para puertas y paneles

de altura estándar

2

Powder Coated & Stainless Steel Restroom Partitions, Floor-Mounted with Overhead Brace — Series 400 Installation

3/21/2018 Bradley • HDWT-INSTR-009 Rev K; ECN 17-14-007

Table of Contents

Pre-Installation Information .................................................................................3

Supplies Required ........................................................................................4

Hardware Provided........................................................................................4

Example of Submittal Drawing ...............................................................................4

Layout Dimensions for Brackets..............................................................................5

Mounting Brackets to Wall ................................................................................6-7

Leveling Bolts to Pilaster ...................................................................................7

Pilaster Mounting Hardware...............................................................................8-9

Pilasters and Panels...................................................................................10-12

Telescoping and Wall Hung Pilasters ......................................................................13-16

Headrail ...............................................................................................17

Pilaster Shoes ..........................................................................................18

Hinges .............................................................................................19-22

Door Hardware.......................................................................................23-26

Urinal Screens .......................................................................................27-29

Table des matières

Avant l’installation........................................................................................30

Fournitures requises......................................................................................31

Visserie fournie..........................................................................................31

Exemple de plan de soumission .........................................................................31-32

Dimensions de placement - Supports continus (en option) ........................................................32

Montage des supports au mur ...........................................................................33-34

Vis de niveau sur montant .................................................................................34

Montage des supports sur les montants ...................................................................35-36

Visserie de fixation de montant .............................................................................36

Montants et panneaux .................................................................................37-39

Montants télescopiques et fixés au mur....................................................................40-43

Barre de tête............................................................................................44

Sabots de montant .......................................................................................45

Charnières ..........................................................................................46-49

Quincaillerie de porte ..................................................................................50-53

Séparateurs d’urinoir ..................................................................................54-56

Contenido

Información previa a la instalación...........................................................................57

Materiales necesarios ....................................................................................58

Piezas metálicas proporcionadas............................................................................58

Ejemplo de plano original..................................................................................58

Dimensiones de diseño para los soportes.....................................................................59

Soporte de montaje para pared ..........................................................................60-61

Pernos niveladores para pilastra ............................................................................61

Soporte de montaje para pilastras........................................................................62-63

Pilastras y paneles ....................................................................................64-66

Pilastras de extensión y para montaje en la pared ...........................................................67-70

Dintel .................................................................................................71

Pedestales para pilastra...................................................................................72

Bisagras ............................................................................................73-76

Piezas metálicas para puertas...........................................................................77-80

Mamparas del urinario .................................................................................81-83

3

Installation Powder Coated & Stainless Steel Restroom Partitions, Floor-Mounted with Overhead Brace — Series 400

Bradley • HDWT-INSTR-009 Rev K; ECN 17-14-007 3/21/2018

WARNING

Before beginning installation, make sure that the wall and floor backing are adequate to support the secure

mounting of the toilet compartment units.

NOTICE

To prevent warping, always lay the material flat. Do not lean the material against the wall or stack unevenly.

To prevent "dimpling," extra caution should be taken when instructed to drill through one side of face only.

IMPORTANT

Read this installation manual completely to ensure proper installation, then file it with the owner or

maintenance department. This installation manual provides instruction for the assembly of normal partition

configurations and standard components. Non-standard configurations or components including but not

limited to curved or angled walls, partial walls, oversized panels, or modified hardware are not covered in

this manual. Compliance and conformity to local codes and ordinances is the responsibility of the installer.

Separate parts from packaging and make sure all parts are accounted for before discarding packaging

material. If any parts are missing, do not begin installation until you obtain the missing parts.

Product warranties and parts information may be found on Bradley's web site at bradleycorp.com.

4

Powder Coated & Stainless Steel Restroom Partitions, Floor-Mounted with Overhead Brace — Series 400 Installation

3/21/2018 Bradley • HDWT-INSTR-009 Rev K; ECN 17-14-007

HR062

HR120

Supplies Required:

Hardware Provided

#14-16 Plastic

Anchor

FAST-T373

#14 x 2"

Button-Head

Sheet Metal Screw

Torx-T27 Drive

FAST-P002

(Stainless)

#10 x 5/8"

Button-Head

Sheet Metal Screw

Torx-T27 Drive

FAST-Z0019

Example of Submittal Drawing

• Chalk line and pencil

• Tape measure and 4' level

• Jigsaw (or hacksaw) and circular saw

• Two spring clamps

• 1/8", 9/64", 3/16", 7/32" and 1/4" drill bits

• Power drill or screw gun with drill bit extension

• 1/4" and 5/16" ceramic tile and masonry drill bit

• Hammer drill

• Spacer, 12" (305mm) high and strong enough to

support weight of panel

#14 x 5/8"

Button-Head

Sheet Metal Screw

Torx-T27 Drive

FAST-Z0016

#5-40 x 11/16"

Flat-Head

Sheet Metal Screw

Torx-T10 Drive

FAST-T300

1/4" - 14 x 5/8"

Sheet Metal Screw

Torx-T27 Drive

FAST-S355A

#10 x 3/4"

Flat-Head

Sheet Metal Screw

Torx-T25 Drive

FAST-Z0006

#14 x 2"

Button-Head

Sheet Metal Screw

Torx-T27 Drive

FAST-Z002

(Chrome Plated)

#10-24 x 3/4"

Button-Head

Barrel Nut

Torx-T27 Drive

FAST-Z003

(Chrome Plated)

#10-24 x 3/4"

Button-Head

Barrel Nut

Torx-T27 Drive

FAST-P003

(Stainless)

#10-24 x 3/4"

Button-Head

Shoulder Screw

Torx-T27 Drive

FAST-Z004

(Chrome Plated)

#10-24 x 3/4"

Button-Head

Shoulder Screw

Torx-T27 Drive

FAST-P004

(Stainless)

#10-24 x 1"

Button-Head

Shoulder Screw

Torx-T27 Drive

FAST-Z004A

(Chrome Plated)

#10-24 x 1"

Button-Head

Shoulder Screw

Torx-T27 Drive

FAST-P004A

(Stainless)

#10 x 2"

Flat-Head

Machine Screw

Torx-T25 Drive

FAST-Z0027

5/16" - 18 x 3"

Leveling Bolt

FAST-S0039

61-1/4"

(1556mm)

to face

60-1/2"

(1537mm)

wall to

centerline

36"

(914mm)

center to

center

36"

(914mm)

24"

(610mm)

26"

(660mm)

8"

(203mm)

3" (76mm)

1" (25mm) gap

1"

(25mm)

gap

1/2"

(13mm)

gap

3"

3-1/2"

1-1/2"

20-1/2"

6-1/2"

58-1/2"

(1486mm)

58-1/2"

(1486mm)

#10 x 2"

Flat-Head

Sheet Metal Screw

Torx-T25 Drive

Fast-S0023

#10 x 5/8"

Button-Head

Sheet Metal Screw

Torx-T27 Drive

FAST-S351A

5

Installation Powder Coated & Stainless Steel Restroom Partitions, Floor-Mounted with Overhead Brace — Series 400

Bradley • HDWT-INSTR-009 Rev K; ECN 17-14-007 3/21/2018

*

C

L

C

L

C

L

C

L

C

L

C

L

Pilaster plumb line

When installing the partition components, consult

the applicable Mills Partition submittal drawing

for compartment layout dimensions.

1

Layout Dimensions - Stirrup Brackets (Standard)

Pilaster centerline: Measure from

the back wall forward to the face of the

compartment, subtract 5/8" (16mm) and

mark this location on the floor (“A”). Mark

the same measurement on the opposite end

of your layout (“A1”) and draw a straight line

connecting both marks.

For freestanding (FS) partitions: Refer

to submittal drawings and determine the

approximate location of the outside panels.

Establish dimensions “A” and “A1” as

explained above.

A

Panel centerline: Measure the stall width across the

back wall and place a mark at the base of the rear wall

(“B”). Repeat this step for each panel, starting each

measurement from the last panel centerline (“B1”).

B

Draw a plumb line on all walls from each pilaster

and panel centerline. From the highest point in the

room, measure 18" (457mm) and 64" (1626mm)

from the floor and place a mark on the pilaster/

panel plumb line. These marks represent the hole

center line of the stirrup brackets. Use a level to

transfer that mark to all other plumb lines (“C”).

C

Panel

plumb line

C

L

C

L

C

L

C

L

*

Pilaster plumb line

When installing the partition components,

consult the applicable Mills Partition submittal

drawing for compartment layout dimensions.

1a

Layout Dimensions - Continuous Brackets (Optional)

Pilaster centerline: Measure from

the back wall forward to the face of the

compartment, subtract 5/8" (16mm)

and mark this location on the floor (“A”).

Mark the same measurement on the

opposite end of your layout (“A1”) and

draw a straight line connecting both

marks.

For freestanding (FS) partitions:

Refer to submittal drawings and

determine the approximate location

of the outside panels. Establish

dimensions “A” and “A1” as explained

above.

A

Panel centerline: Measure the stall width across the

back wall and place a mark at the base of the rear wall

(“B”). Repeat this step for each panel, starting each

measurement from the last panel centerline (“B1”).

B

Draw a plumb line on all walls from each pilaster and panel

centerline. From the highest point in the room, measure from

the floor and place a mark on the pilaster/panel plumb line at

dimension "C" for the respective bracket type (see table below).

Use a level to transfer that mark to all other plumb lines "D".

C

Panel

plumb line

64"

(1626mm)

18"

(457mm)

"C"

"D"

"C"

"D"

"C"

"D"

"C"

"B"

"B1"

"A1"

"A"

"C"

Dim "C"

Stainless

Steel

12-1/2"

(318mm)

Aluminum

12-1/4"

(311mm)

6

Powder Coated & Stainless Steel Restroom Partitions, Floor-Mounted with Overhead Brace — Series 400 Installation

3/21/2018 Bradley • HDWT-INSTR-009 Rev K; ECN 17-14-007

2

Stirrup Brackets to Wall (Standard)

established level line

pilaster/panel plumb line

floor

C

L

Place the center of each stirrup bracket

at the established level line. Center the

bracket opening on the pilaster/panel

plumb line.

A

Insert the plastic anchors in all holes and

secure the brackets to the wall with the

#14 x 2" screws provided.

C

On end panel and pilaster applications, position the bracket

with the ear facing toward the inside of the stall.

Using the bracket as a template, mark the

hole locations on the wall. Remove the

bracket and drill a Ø5/16" hole (min. 2"

[51mm] deep) at each hole location.

B

One-Eared

Bracket

Two-Eared

Bracket

Pilaster bracket is shown here; 1-1/4" opening brackets are

for pilasters, and 1" opening brackets are for panels.

2a

Continuous Stainless Steel Brackets to Wall (Optional)

established level line

pilaster plumb

line

floor

C

L

Place the bottom of each continuous

bracket at the established level line.

Center the bracket opening on the

pilaster/panel plumb line.

A

Insert the plastic anchors in all holes and

secure the brackets to the wall with the

#14 x 2" stainless screws provided.

C

On pilaster applications, position the bracket with the ear

facing toward the inside of the stall.

Using the bracket as a template, mark the

hole locations on the wall. Remove the

bracket and drill a Ø5/16" hole (min. 2"

[51mm] deep) at each hole location.

B

Brackets are used as templates, but since the hole patterns

may be different, the brackets may not be interchangeable.

Pilaster bracket is shown here; "Ear" brackets are for pilasters, and

"U" brackets are for panels.

"Ear"

Bracket

"U" Bracket

7

Installation Powder Coated & Stainless Steel Restroom Partitions, Floor-Mounted with Overhead Brace — Series 400

Bradley • HDWT-INSTR-009 Rev K; ECN 17-14-007 3/21/2018

2b

Continuous Aluminum Brackets to Wall (Optional)

established level line

pilaster/panel

plumb line

floor

C

L

Place the bottom of each continuous

bracket at the established level line.

Center the bracket opening on the

pilaster/panel plumb line.

A

Insert the plastic anchors in all holes and

secure the brackets to the wall with the

#14 x 2" stainless screws provided.

C

On end panel and pilaster applications, position the bracket

with the ear facing toward the inside of the stall.

Using the bracket as a template, mark the

hole locations on the wall. Remove the

bracket and drill a Ø5/16" hole (min. 2"

[51mm] deep) at each hole location.

B

Brackets are used as templates, but since the hole patterns

may be different, the brackets may not be interchangeable.

Pilaster bracket is shown here; 1-1/4" opening brackets are for

pilasters, and 1" opening brackets are for panels.

One-Eared

Bracket

Two-Eared

Bracket

3

Leveling Bolts to Pilaster

Use leveling bolt(s) to adjust height of pilaster

as indicated based on pilaster width.

A

3" Pilaster 4" - 14" Pilaster 18" - 24" Pilaster

4" - 8" pilasters have a single, 1-piece bracket that uses a

leveling bolt in the center to adjust the pilaster height.

8

Powder Coated & Stainless Steel Restroom Partitions, Floor-Mounted with Overhead Brace — Series 400 Installation

3/21/2018 Bradley • HDWT-INSTR-009 Rev K; ECN 17-14-007

4

Stirrup Brackets to Pilaster (Standard)

Refer to the submittal drawing to locate the split

dimension and layout location of each marked pilaster.

Measure 17-7/16 (443mm) and 63-7/16" (1611mm) down from

the top of each pilaster and place a mark on the pilaster split

centerline.

A

Split

17-7/16"

(443mm)

63-7/16"

(1611mm)

Place stirrup brackets at each established level line. Center

the bracket opening on the pilaster split centerline. Using the

bracket as a template, mark the hole locations on the pilaster.

Remove the bracket and drill a Ø3/16" pilot hole (through

inside face of pilaster only) at each location.

B

Secure the stirrup brackets to the pilasters using the #14 x 5/8"

screws provided.

C

4a

Continuous Brackets to Pilaster (Optional)

Refer to the submittal drawing to locate the split

dimension and layout location of each marked pilaster.

Measure down from the top of the pilaster and

place a mark on the pilaster split centerline

at dimensions "A" and "B" for the respective

bracket (see table at left).

A

Secure the continuous bracket to the

pilasters using the #14 x 5/8" stainless

screws provided.

C

Split

"A"

"B"

Dim. "A" Dim. "B"

Stainless

Steel

Bracket

11-15/16"

(302mm)

69-15/16"

(1749mm)

Aluminum

Bracket

11-11/16"

(297mm)

69-3/16"

(1749mm)

Place the continuous bracket between each

established level line. Center the bracket

opening on the pilaster split centerline. Using

the bracket as a template, mark the hole

locations on the pilaster. Remove the bracket

and drill a Ø3/16" pilot hole (through inside

face of pilaster only) at each location.

B

Brackets are used as templates but since the hole patterns

may be different, the brackets may not be interchangeable.

Continuous stainless steel bracket shown.

Pilaster shown is for reference only. Actual pilaster varies

depending on application.

Pilaster shown is for reference only. Actual

pilaster varies depending on application.

C

L

C

L

C

L

9

Installation Powder Coated & Stainless Steel Restroom Partitions, Floor-Mounted with Overhead Brace — Series 400

Bradley • HDWT-INSTR-009 Rev K; ECN 17-14-007 3/21/2018

5

Pilaster Mounting Hardware

This view is an example only. Refer to your submittal drawings to determine placement of the anchors on the pilaster

centerline for your application. Typical anchor centers are measured 1" (25mm) in from each edge of the pilaster (except 3"

pilasters where only one anchor is used).

A

Insert plastic anchors into the holes and

fasten the "L" brackets to the anchors

using the #14 x 2" screws provided.

C

Drill Ø5/16" holes (min 2" [51mm] deep) in

the floor and make sure the holes are free

of dirt and debris.

B

38"

(965mm)

Pilaster Centerline

22"

(559mm)

3"

(76mm)

6"

(152mm)

28"

(711mm)

4b

Alcove Brackets to Pilaster

Layouts that use continuous aluminum brackets for pilaster and panel connections will use stirrup brackets for alcove connections.

Continuous stainless steel brackets use continuous alcove brackets.

Refer to the submittal drawing for the layout location of each alcove pilaster.

Measure down from the top of

the pilaster and place a mark at

dimensions shown for the respective

bracket situation.

A

Stirrup: Position the center of each

bracket at the marks made in Step A.

Continuous: Center the bracket

between each mark made in Step A.

B

Using the bracket as a template,

mark the hole locations on the

pilaster. Remove the bracket and drill

Ø3/16" holes through the pilaster at

each location.

C

Secure the bracket(s) to the

pilaster using the #14 x 5/8" screws

(stainless on continuous) provided.

D

63-7/16"

(1611mm)

17-7/16"

(443mm)

Stirrup

Continuous

68-15/16"

(1749mm)

11-15/16"

(302mm)

10

Powder Coated & Stainless Steel Restroom Partitions, Floor-Mounted with Overhead Brace — Series 400 Installation

3/21/2018 Bradley • HDWT-INSTR-009 Rev K; ECN 17-14-007

6

Pilasters and Panels with Stirrup Brackets (Standard)

Pilasters located at walls should be mounted ﬁrst. Start at one end and install a panel, then a pilaster. Continue alternating until

installation is complete. When installing in an alcove or in-corner, use an alcove bracket to secure the pilaster to the panel.

Pilasters at Wall

Pilasters with Panels

Check to make sure the pilasters are plumb and level to each other. The pilaster height can be adjusted with the leveling bolt that

was placed at the bottom of the pilaster (see page 5 for attaching leveling bolt).

When installing pilasters at walls, the gaps range

from 1/2" to 1-1/4" (13mm to 32mm). Refer to your

submittal drawing for your gap sizes.

Refer to your submittal drawing and leave the appropriate

gaps. Standard gap is 1" (25mm) between the panel and

wall and 1/2" (13mm) between the panel and pilaster.

Spacer 12" (305mm)

Slide the shoe onto the bottom of the pilaster and

use a piece of tape to keep the shoe positioned

above the mounting hardware. Make sure the shoe

mounting hole is facing inside the stall and that the

hole is towards the top.

A

Position the pilaster so the mounting bracket(s)

sits on the inside of the floor "L" bracket(s) while at

the same time placing the pilaster within the wall

brackets. Secure the pilaster mounting bracket(s) to

the floor "L" bracket(s) using the #14 x 5/8" screw(s)

provided.

B

Using the bracket as a template, drill Ø3/16" holes

through the pilaster at each pilaster bracket hole.

Secure the pilaster to the bracket using the

#14 x 5/8" screws provided.

C

Using the bracket as a template, drill Ø3/16" holes through

the panel at each panel bracket hole. Secure the panel to

the bracket using the #14 x 5/8" screws provided.

D

Place the panel on the spacer and insert the panel into the

wall brackets.

A

Slide the shoe onto the bottom of the pilaster and use

a piece of tape to keep the shoe positioned above the

mounting hardware. Make sure the shoe mounting hole is

facing inside the stall and that the hole is towards the top.

B

Position the pilaster so the mounting bracket(s)sits on the

inside of the floor "L" bracket(s) while at the same time

placing the brackets around the panel. Secure the pilaster

mounting bracket(s) to the floor "L" bracket(s) using the

#14 x 5/8" screw(s) provided.

C

11

Installation Powder Coated & Stainless Steel Restroom Partitions, Floor-Mounted with Overhead Brace — Series 400

Bradley • HDWT-INSTR-009 Rev K; ECN 17-14-007 3/21/2018

Pilasters at Wall Pilasters with Panels

6a

Pilasters and Panels with Stainless Steel Continuous Brackets (Optional)

Pilasters located at walls should be mounted ﬁrst. Start at one end and install a panel, then a pilaster. Continue alternating until

installation is complete. When installing in an alcove or in-corner, use an alcove bracket to secure the pilaster to the panel.

Check to make sure the pilasters are plumb and level to each other. The pilaster height can be adjusted with the

leveling bolt that was placed at the bottom of the pilaster (see page 5 for attaching leveling bolt).

Spacer 12" (305mm)

When installing pilasters at walls, the gaps range

from 1/2" to 1-1/4" (13mm to 32mm). Refer to your

submittal drawing for your gap sizes.

Refer to your submittal drawing and leave the appropriate

gaps. Standard gap is 1" (25mm) between the panel and

wall and 1/2" (13mm) between the panel and pilaster.

Slide the shoe onto the bottom of the pilaster and

use a piece of tape to keep the shoe positioned

above the mounting hardware. Make sure the shoe

mounting hole is facing inside the stall and that the

hole is towards the top.

A

Position the pilaster so the mounting bracket(s)

sits on the inside of the floor "L" bracket(s) while at

the same time placing the pilaster within the wall

bracket. Secure the pilaster mounting bracket(s) to

the floor "L" bracket(s) using the #14 x 5/8" screw(s)

provided.

B

Place the panel on the spacer and insert the panel into the

wall bracket.

A

Slide the shoe onto the bottom of the pilaster and use a piece

of tape to keep the shoe positioned above the mounting

hardware. Make sure the shoe mounting hole is facing inside

the stall and that the hole is towards the top.

B

Position the pilaster so the mounting bracket(s) sits on the

inside of the floor "L" bracket(s) while at the same time placing

the bracket around the panel. Secure the pilaster mounting

bracket(s) to the floor "L" bracket(s) using the #14 x 5/8"

screw(s) provided.

C

Using the bracket as a template, drill Ø3/16" holes

through the pilaster at each pilaster bracket hole.

Secure the pilaster to the bracket using the

#14 x 5/8" stainless screws provided.

C

Using the bracket as a template, drill Ø3/16" holes through

the panel at each panel bracket hole. Secure the panel to the

bracket using the #14 x 5/8" stainless screws provided.

D

12

Powder Coated & Stainless Steel Restroom Partitions, Floor-Mounted with Overhead Brace — Series 400 Installation

3/21/2018 Bradley • HDWT-INSTR-009 Rev K; ECN 17-14-007

Pilasters at Wall Pilasters with Panels

6b

Pilasters and Panels with Aluminum Continuous Brackets (Optional)

Pilasters located at walls should be mounted ﬁrst. Start at one end and install a panel, then a pilaster. Continue alternating until

installation is complete. When installing in an alcove or in-corner, use an alcove bracket to secure the pilaster to the panel.

Check to make sure the pilasters are plumb and level to each other. The pilaster height can be adjusted with the

leveling bolt that was placed at the bottom of the pilaster (see page 5 for attaching leveling bolt).

Spacer 12" (305mm)

When installing pilasters at walls, the gaps range

from 1/2" to 1-1/4" (13mm to 32mm). Refer to your

submittal drawing for your gap sizes.

Refer to your submittal drawing and leave the appropriate

gaps. Standard gap is 1" (25mm) between the panel and

wall and 1/2" (13mm) between the panel and pilaster.

Slide the shoe onto the bottom of the pilaster and

use a piece of tape to keep the shoe positioned

above the mounting hardware. Make sure the shoe

mounting hole is facing inside the stall and that the

hole is towards the top.

A

Position the pilaster so the mounting bracket(s)

sits on the inside of the floor "L" bracket(s) while at

the same time placing the pilaster within the wall

bracket. Secure the pilaster mounting bracket(s) to

the floor "L" bracket(s) using the #14 x 5/8" screw(s)

provided.

B

Using the bracket as a template, drill Ø1/4" holes

through the pilaster at each pilaster bracket hole.

Secure the pilaster to the bracket using the

#10-24 x 3/4" stainless barrel nuts and #10-24 x 1"

stainless shoulder screws provided.

C

Using the bracket as a template, drill Ø1/4" holes through the

panel at each panel bracket hole. Secure the panel to the

bracket using the #10-24 x 3/4" stainless barrel nuts and

#10-24 x 3/4" stainless shoulder screws provided.

D

Place the panel on the spacer and insert the panel into the

wall bracket.

A

Slide the shoe onto the bottom of the pilaster and use a piece

of tape to keep the shoe positioned above the mounting

hardware. Make sure the shoe mounting hole is facing inside

the stall and that the hole is towards the top.

B

Position the pilaster so the mounting bracket(s) sits on the

inside of the floor "L" bracket(s) while at the same time placing

the bracket around the panel. Secure the pilaster mounting

bracket(s) to the floor "L" bracket(s) using the #14 x 5/8"

screw(s) provided.

C

13

Installation Powder Coated & Stainless Steel Restroom Partitions, Floor-Mounted with Overhead Brace — Series 400

Bradley • HDWT-INSTR-009 Rev K; ECN 17-14-007 3/21/2018

6c

Telescoping Pilasters (Optional)

Mounting channels are used as templates but may not be interchanged because the hole patterns may be different.

Floor

Pilaster Plumb Line

Mounting Channel

12-1/8" (308mm)

to Bottom of

Channel (Highest

Point in Floor)

Telescoping Pilaster at Wall

Wall, Pilaster or Panel

Mounting Channel

Telescoping

Channel

Specified

Dimension

Telescoping Pilaster at Pilaster

12-5/16"

(313mm)

Pilaster

Centerline

Mounting Channel

Wall: From the highest point in the room, measure 12-1/8"

(308mm) up from the floor and transfer this level line to

the pilaster plumb line. Place the bottom of the mounting

channel at the level line and center the channel opening on

the plumb line.

Pilaster: Measure 12-5/16" (313mm) down from the top

of the pilaster and place a mark on the pilaster centerline.

Place the top of the mounting channel at this mark and

center the channel opening on the centerline.

A

Wall: Using the mounting channel as a template, mark the

hole locations and remove mounting channel. Drill a Ø5/16"

hole (min 2" [51mm] deep) at each hole location.

Pilaster: Using the mounting channel as a template, mark

the hole locations and remove the mounting channel. Drill a

Ø1/4" hole through the pilaster.

B

Wall: Insert the plastic anchors in all holes and secure

the mounting channel to the wall with the #14 x 2" screws

provided.

Pilaster: Secure the mounting channel to the pilaster with

the #10-24 x 3/4" barrel nuts and the #10-24 x 1" shoulder

screws provided.

C

Slide the telescoping channel over the mounting channel.

Refer to the submittal drawings and adjust the width to

meet the specified dimension.

D

Using the holes in the telescoping channel as a template,

drill Ø3/16" holes through the mounting channel. Secure the

telescoping channel to the mounting channel with the

#14 x 5/8" screws provided.

E

14

Powder Coated & Stainless Steel Restroom Partitions, Floor-Mounted with Overhead Brace — Series 400 Installation

3/21/2018 Bradley • HDWT-INSTR-009 Rev K; ECN 17-14-007

6d

Wall-Hung Pilasters (58" or 69-9/16") - Stirrup Brackets (Optional)

To establish level line, from the highest point in the room, measure 12" (305mm) from the ﬂoor. Use a level to transfer

this mark to the pilaster plumb line.

See Step 2 for instructions on mounting the stirrup brackets to a wall.

Wall

Specified Dimension

(Standard Gap 1")

12"

(305mm)

Pilaster

Plumb Line

Floor

Pilasters at Wall Pilasters at Pilasters

Specified

Dimension

See Step 4 for instructions on mounting the stirrup brackets to a pilaster.

Floor

Pilasters shown in two different lengths for visual reference.

69-9/16" (1767mm)

Pilaster

58" (1473mm)

Pilaster

Slide the wall-hung pilaster into the stirrup brackets

and align with the established level line. Refer to

the submittal drawing and adjust to meet the

specified dimension.

A

Using the stirrup brackets as a template, drill

Ø3/16" holes through the pilaster at each bracket

hole. Secure the pilaster to the bracket using the

#14 x 5/8" screws provided.

B

Slide the wall-hung pilaster into the stirrup brackets

and align with the established level line. Refer to

the submittal drawing and adjust to meet the

specified dimension.

A

Using the stirrup brackets as a template, drill

Ø3/16" holes through the pilaster at each bracket

hole. Secure the pilaster to the bracket using the

#14 x 5/8" screws provided.

B

12"

(305mm)

C

L

69-9/16" (1767mm)

Pilaster

58" (1473mm)

Pilaster

15

Installation Powder Coated & Stainless Steel Restroom Partitions, Floor-Mounted with Overhead Brace — Series 400

Bradley • HDWT-INSTR-009 Rev K; ECN 17-14-007 3/21/2018

6e

Wall-Hung Pilasters (58" or 69-9/16") - Continuous Stainless Steel Brackets (Optional)

To establish level line, from the highest point in the room, measure 12" (305mm) from the ﬂoor. Use a level to transfer

this mark to the pilaster plumb line.

See Step 2a for instructions on mounting the continuous stainless

steel brackets to a wall.

Wall

Specified Dimension

(Standard Gap 1")

Pilaster

Plumb Line

Floor

Pilasters at Wall Pilasters at Pilasters

Specified

Dimension

See Step 4a for instructions on mounting the continuous stainless

steel brackets to a pilaster.

Floor

Pilasters shown in two different lengths for visual reference.

Slide the wall-hung pilaster into the continuous

bracket and align with the established level line.

Refer to the submittal drawing and adjust to meet

the specified dimension.

A

Using the continuous bracket as a template, drill

Ø3/16" holes through the pilaster at each bracket

hole. Secure the pilaster to the bracket using the

#14 x 5/8" stainless screws provided.

B

Slide the wall-hung pilaster into the continuous

bracket and align with the established level line.

Refer to the submittal drawing and adjust to meet

the specified dimension.

A

Using the continuous bracket as a template, drill

Ø3/16" holes through the pilaster at each bracket

hole. Secure the pilaster to the bracket using the

#14 x 5/8" stainless screws provided.

B

12"

(305mm)

12"

(305mm)

C

L

69-9/16" (1767mm)

Pilaster

58" (1473mm)

Pilaster

69-9/16" (1767mm)

Pilaster

58" (1473mm)

Pilaster

16

Powder Coated & Stainless Steel Restroom Partitions, Floor-Mounted with Overhead Brace — Series 400 Installation

3/21/2018 Bradley • HDWT-INSTR-009 Rev K; ECN 17-14-007

6f

Wall-Hung Pilasters (58" or 69-9/16") - Continuous Aluminum Brackets (Optional)

To establish level line, from the highest point in the room, measure 12" (305mm) from the ﬂoor. Use a level to transfer

this mark to the pilaster plumb line.

See Step 2b for instructions on mounting the continuous aluminum

brackets to a wall.

Wall

Specified Dimension

(Standard Gap 1")

Pilaster

Plumb Line

Floor

Pilasters at Wall Pilasters at Pilasters

Specified

Dimension

See Step 4a for instructions on mounting the continuous

aluminum brackets to a pilaster.

Floor

Pilasters shown in two different lengths for visual reference.

Slide the wall-hung pilaster into the continuous

bracket and align with the established level line.

Refer to the submittal drawing and adjust to meet

the specified dimension.

A

Using the continuous bracket as a template, drill

Ø1/4" holes through the pilaster at each bracket

hole. Secure the pilaster to the bracket using the

#10-24 x 3/4" stainless barrel nuts and #10-24 x 1"

stainless shoulder screws provided.

B

Slide the wall-hung pilaster into the continuous

bracket and align with the established level line.

Refer to the submittal drawing and adjust to meet

the specified dimension.

A

Using the continuous bracket as a template, drill

Ø1/4" holes through the pilaster at each bracket

hole. Secure the pilaster to the bracket using the

#10-24 x 3/4" stainless barrel nuts and #10-24 x 1"

stainless shoulder screws provided.

B

12"

(305mm)

12"

(305mm)

69-9/16" (1767mm)

Pilaster

58" (1473mm)

Pilaster

69-9/16" (1767mm)

Pilaster

58" (1473mm)

Pilaster

C

L

17

Installation Powder Coated & Stainless Steel Restroom Partitions, Floor-Mounted with Overhead Brace — Series 400

Bradley • HDWT-INSTR-009 Rev K; ECN 17-14-007 3/21/2018

7

Headrail

Make sure the pilasters are plumb and that the pilaster has been secured to the mounting hardware. Leave the appropriate

door opening between the pilasters as shown on your submittal drawing.

Completed Headrail Assembly

The illustrations on this page show mounting hardware and fasteners for a generic application. Refer to your submittals

to determine your actual headrail conﬁgurations.

Some headrail sections may need to be cut to an appropriate size. Refer to your submittals for general headrail placement.

Headrail conﬁgurations that come to an intersection should meet over pilaster (see completed headrail assembly view below).

Wall

Place headrail over the top of each pilaster

located at the wall and slide it tight against the

side wall. Mark the outline of the headrail on the

wall and remove the headrail.

A

Place the headrail bracket on

the outline marked on the wall

and mark the locations of the

mounting holes. Remove bracket

and drill (2) Ø5/16" holes a

minimum of 2" [51 mm] deep.

Prior to securing to the wall,

enlarge the (2) back mounting

holes of the bracket to Ø1/4".

Secure the bracket to the wall

with the #14 x 2" screws and

plastic anchors provided.

B

Place headrail over the top of the pilasters and

slide it tight into the mounting bracket. Use the

mounting bracket as a template and drill a Ø7/32"

hole through the headrail. Secure the headrail to

the mounting bracket with the #10 x 5/8" screws

provided.

C

Make sure the pilaster is plumb

and that the spacing between

the pilasters for the doors is the

correct dimension. On the back

of each pilaster (starting with the

first pilaster), drill a Ø7/32" hole

through one face of the headrail

only.

Using this hole as a template,

drill a Ø9/64" pilot hole into the

pilaster, 5/8" (16mm) deep.

Secure the headrail to the

back of each pilaster with the

#10 x 5/8" screws provided.

D

For open end applications, cut the headrail to the appropriate length (if

required). Attach the bracket to the wall at the correct height (see step B).

Attach another bracket to a pilaster with #10 x 5/8" screws at the correct height

(see view below). The headrail should be level with any adjacent headrail

and should be located directly over the panel. Position each headrail onto the

brackets and secure with required fasteners (see step C). Using a rubber mallet,

install the headrail end cap.

E

18

Powder Coated & Stainless Steel Restroom Partitions, Floor-Mounted with Overhead Brace — Series 400 Installation

3/21/2018 Bradley • HDWT-INSTR-009 Rev K; ECN 17-14-007

8

Pilaster Shoes

Position pilaster shoe so that it rests flush with the floor.

A

Using the hole(s) in the shoe as a template, drill a Ø9/64"

pilot hole (through inside face of pilaster only). Secure

the shoe to the pilaster using the #10 x 5/8" fastener(s)

provided.

B

19

Installation Powder Coated & Stainless Steel Restroom Partitions, Floor-Mounted with Overhead Brace — Series 400

Bradley • HDWT-INSTR-009 Rev K; ECN 17-14-007 3/21/2018

9

Wraparound Gravity Hinges (Standard)

Before installing the hinges, make sure the door openings are the appropriate size, all pilasters are plumb,

secured to the ﬂoor and that the headrail is installed.

Right-hand

inswing

(RHI)

Left-hand

inswing

(LHI)

Right-hand

outswing

(RHO)

Left-hand

outswing

(LHO)

"A"

"B" "B" "B"

"A"

Dim. "A" Dim. "B"

Floor

Mounted

Overhead

Braced

13-1/2"

(343mm)

67-5/8"

(1718mm)

Wall Hung

69-9/16"

(1767mm)

13-1/2"

(343mm)

67-5/8"

(1718mm)

Wall Hung

58"

(1473mm)

2-1/16"

(52mm)

56-3/16"

(1427mm)

Floor Mounted Overhead Braced

Wall Hung

69-9/16" (1767mm)

Wall Hung

58" (1473mm)

For 58" wall hung pilaster, establishing dimensions "A" and "B" as shown in the table will

result in the top of the door being ﬂush with the top of the pilaster when the desired cam

setting on the door is set to 0°.

Refer to your submittal drawings to determine each speciﬁc door swing for your application. The door swing is

determined by facing the compartment from the outside. The image below can help determine the door swing type.

Measure down from the top of the pilaster and

place a mark at dimensions "A" and "B" for the

respective pilaster type (see table below). This

mark represents the upper hole location of the top

and bottom hinge.

A

Using the hinge as a template, drill Ø1/4" holes

through the pilaster.

B

20

Powder Coated & Stainless Steel Restroom Partitions, Floor-Mounted with Overhead Brace — Series 400 Installation

3/21/2018 Bradley • HDWT-INSTR-009 Rev K; ECN 17-14-007

Secure the top and bottom pilaster hinge to the pilaster

with the #10-24 x 3/4" barrel nuts and #10-24 x 1"

shoulder screws provided.

C

Assemble the bottom hinge cam and pin as shown.

Insert into the bottom hinge and thread the locknut

loosely onto the bottom hinge pin.

D

Rotate the door to the desired "at rest" position. Push

down on the door while holding it in the "at rest"

position. This sets the male and female cams in the

bottom hinge. Tighten the hex nut to secure the door in

the "at rest" position.

F

9

Wraparound Gravity Hinges (Continued)

The door hinge assembly consists of separate door

and pilaster hardware.

Door cam surfaces can become worn under normal use.

The application of lithium grease can help prolong door

cam life and reduce friction between surfaces.

The top hinge pin should snap securely

into place.

Bottom

Hinge

Cam

Lock Nut

Top Hinge

Finished View

of Top Hinge

Finished View

of Bottom Hinge

Place the bottom door hinge opening onto the bottom

pilaster hinge. Position the top door hinge opening into

the top pilaster hinge and insert the top hinge pin.

E

For doors requiring a full close, rotate the

door 15° past the closed position.

La page est en cours de chargement...

Bradley 400 Series Guide d'installation

Bradley 400 Series Guide d'installation

dans d''autres langues

Documents connexes

Autres documents