Part Names/Control Descriptions
Specifications
l
System:
SYSTEM-70
l
Pickup:
Original Bar Sensor (Piezo Type)
l
Control:
Line Out Volume (Combined w/TA Switch
*
1
), Reverb Effect (Room/Hall), Chorus Effect.
l
Output Jack:
Combination End Pin/Line Out Power Switch
*
2
l
Output Imped-
ance:
150Ω
l
Power:
AA battery x2 (alkaline or nickel-metal hydride)
*
3
l
Battery Life:
Approximately 10 hours using alkaline batteries (with the TA function
in use).
*
4
l
Accessories:
Neck adjustment hex wrench x1, AA battery x2
*1 The TA function produces effect sounds from the body of the guitar to add to the
guitar’s original sound. The system requires approximately two seconds after the TA
function is switched ON before the rst effect sound is produced.
*2 Connect a cable for line output.
*3 For best performance, we recommend the use of alkaline or nickel-metal hydride
batteries. When using nickel-metal hydride batteries, please follow the instructions in
the manual provided with the batteries.
*4 Depending upon operating conditions.
Replacing the Batteries
q
Slide the tab on the endpin section in the direction indicated by the arrow in the diagram
below to release the lock, then pull out the battery holder.
w
Insert two AA batteries making sure that the battery poles are properly aligned with the
polarity markings on the battery holder.
e
Slide the battery holder back into the endpin section until it locks.
* When using nickel metal-hydride batteries, take care not to damage the battery cas-
ing or poles when installing and removing the batteries.
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
Please keep this manual in a safe and handy place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury
or even death from electrical shock, short-circuiting, damages, fire or other hazards.
These precautions include, but are not limited to, the following:
Do not open
•
This instrument contains no user-serviceable parts. Do not open the instrument or attempt to
disassemble or modify the internal components in any way. If it should appear to be malfunction
-
ing, discontinue use immediately and have it inspected by qualified Yamaha service personnel.
Water warning
•
To avoid damage, do not expose the guitar to damp/rainy conditions or place it near any containers
such as vases, bottles, or glasses that have the potential to spill into any of the guitar’s openings or
electronic components. Should any moisture/liquid seep into the guitar (such as water), turn off the
power immediately and have the instrument inspected by qualified Yamaha service technician.
If you notice any abnormality
•
Should one of the following problems occur, immediately turn off the power, remove all batteries
from the instrument and have the instrument inspected by a qualified Yamaha service technician.
- Emission of unusual smells or smoke.
- An object has been dropped into the instrument.
- A sudden loss of sound.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical
injury to you or others, or damage to the instrument or other property. These precautions
include, but are not limited to, the following:
Connection
•
Before connecting the instrument to other electronic components, turn off the power for all compo-
nents. Before turning the power on or off for all components, set all volume levels to minimum.
• Be sure to set the volumes of all components at their minimum levels and gradually raise
the volume controls while playing the instrument to set the desired listening level.
Location
• Do not place the instrument in an unstable position where it might accidentally fall over.
Handling caution
• Do not rest your weight on, or place heavy objects on the instrument, and do not use
excessive force on the buttons, switches or connectors.
• Do not use the instrument/device or headphones for a long period of time at a high or
uncomfortable volume level, since this can cause permanent hearing loss. If you experi-
ence any hearing loss or ringing in the ears, consult a physician.
* Yamaha cannot be held responsible for damage caused by improper use or modifi-
cations made to this instrument.
* Information regarding the batteries can be found in the Specifications Section of this
owner’s manual.
* Please review the Operating Procedures section of this manual prior to connecting
your guitar to an external audio device such as a guitar amplifier, etc.
Operating Procedures
l
Using without an amplifier (Only using the TA function)
Add reverb and/or chorus effects to the guitars acoustic sound.
q
Push the TA switch to turn ON the TA function (green LED lights).
w
Use the Reverb and Chorus controls to adjust each effect.
* Please take note that high effect volume levels can result in feedback.
l
Using with an amplifier, etc. (used as an electric acoustic guitar).
The sound, with effects applied, can be output via the output jack.
q
Connect a cable to the output jack to send the signal to external equipment (red LED lights).
w
Use the Line Out Volume control to adjust the volume, and the Reverb and Chorus controls
to adjust each effect.
* In this condition, the TA ON/OFF switch can be used to select whether or not to si-
multaneously generate the effect sound from the guitar’s body. When the TA switch
is OFF, the effects are still output via the line out signal.
e
Removing the cable from the output jack switches the power OFF (the TA function also
switches OFF at this time).
Auto Power-Off Function
Both the power and the TA function automatically switch off if there is no input for more than 30 minutes.
* The auto power-off function is disabled when a cable is connected to the instrument.
* The TA function power is also switched off when feedback is produced for more
than 30 seconds.
Thank you for purchasing the Yamaha TransAcoustic
TM
Guitar. The TransAcoustic
TM
guitar
is a unique and innovative instrument that enhances the natural sound and dimension of
a Yamaha acoustic guitar by utilizing its body and proprietary technology to offer musi
-
cians a new immersive acoustic playing experience. To obtain the best performance and
potential from this instrument, we encourage you to read this manual before use.
Note that this manual covers only the electronic parts of this product. For information on
the other non-electronic parts, refer to the separate Acoustic Guitar Owner’s Manual.
q
Release the lock
AA battery
x2
Battery Holder
Tab
q
Line Out Volume Control/TA Switch
To turn on the TransAcoustic guitar, press this knob for approximately 0.3 seconds.
When a cable is connected to the TransAcoustic’s output/line out jack, the output level
can be adjusted by rotating this control to the right (clockwise) to increase the level, or
to the left (counterclockwise) to reduce the level.
w
Reverb Control
Adjusts the reverb effect. Turning this control to the right (clockwise) increases the level
of the effect and selects between the TransAcoustic’s two reverb types: Room and Hall
(in the 12:00 position). Turning it all the way to the left (counterclockwise) bypasses/
switches the reverb effect off.
e
Chorus Control
Adjusts the chorus effect. Turing this control to the right (clockwise) increases in the
intensity of the chorus effect. Turning it all the way to the left (counterclockwise) by-
passes/switches the chorus effect off.
r
Output Jack/Battery Holder
The output jack and battery compartment are combined into a single unit. Inserting a
plug into the output jack switches the internal preamplifier ON.
*
To prolong the life of your battery, please unplug the cable from the output jack when not in use.
LED Display Details
The LED located inside the sound hole flashes red when it is time to change the batteries.
Once the LED begins flashing, the remaining operation time is approximately two hours
with alkaline batteries and about one hour when using nickel metal hydride batteries (Time
varies according to operating conditions). Please replace the batteries as soon as possible.
Green LED Red LED Condition
Lights Lights TA Function ON, Line Out ON
Lights — TA Function ON
— Lights Line Out ON
— Flashing Battery Warning
LED
Controls
EN
TransAcoustic
TM
Guitar
System70
Owner’s Manual
警告
この表示内容を無視した取り扱いをすると、
死亡や重症を負う可能性が想定されます。
電池
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious
injury or even death from electrical shock, short-circuiting, damages, fire or other
hazards. These precautions include, but are not limited to, the following:
Battery
• Follow the precautions below. Failure to do so might result in explosion, fire, overheating
or battery fluid leakage.
- Do not tamper with or disassemble batteries.
- Do not dispose of batteries in fire.
- Do not attempt to recharge batteries that are not designed to be charged.
- Keep the batteries separate from metallic objects such as necklaces, hairpins, coins,
and keys.
- Use the specified battery type only.
- Use new batteries, all of which are the same type, same model, and made by the same
manufacturer.
- Always make sure all batteries are inserted in conformity with the +/- polarity markings.
- When the batteries run out, or if the instrument is not to be used for a long time,
remove the batteries from the instrument.
• Do not carry or store batteries with other metal objects such as necklaces, hairpins,
metal coins, or keys.
• If the batteries do leak, avoid contact with the leaked fluid. If the battery fluid should come
in contact with your eyes, mouth, or skin, wash immediately with water and consult a doc-
tor. Battery fluid is corrosive and may possibly cause loss of sight or chemical burns.
Make sure to discard used batteries according to local regulations.
AVVERTENZA
Attenersi sempre alle precauzioni di base indicate di seguito per evitare il rischio
di lesioni gravi o addirittura di morte conseguente a scosse elettriche, cortocircuiti,
danni, incendi o altri pericoli. Tali precauzioni includono, fra le altre, quelle indica-
te di seguito:
Batteria
• Attenersi alle precauzioni indicate di seguito. In caso contrario, si potrebbero causare
esplosioni, incendi, surriscaldamento o fuoriuscite di liquido dalle batterie.
- Non manomettere né disassemblare le batterie.
- Non smaltire le batterie nel fuoco.
- Non ricaricare batterie non ricaricabili.
-
Tenere le batterie lontane da oggetti metallici come collane, fermacapelli, monete e chiavi.
- Utilizzare solo il tipo di batterie specificato.
- Utilizzare batterie nuove, tutte dello stesso tipo, modello e produttore.
- Assicurarsi che tutte le batterie siano inserite nel rispetto delle indicazioni di polarità +/-.
- In caso di esaurimento delle batterie o se si prevede di non utilizzare lo strumento per
molto tempo, rimuovere le batterie dallo strumento.
• Conservare le batterie lontano dalla portata dei bambini, che potrebbero ingerirle acci-
dentalmente.
• In caso di fuoriuscite, evitare il contatto con il liquido delle batterie. Se il liquido delle
batterie viene a contatto con gli occhi, la bocca o la cute, lavare immediatamente con
acqua e rivolgersi a un medico. Il liquido delle batterie è corrosivo e potrebbe causare la
perdita della vista o ustioni chimiche.
Smaltire le batterie esauste in conformità alle normative locali.
AG-Stomp の電源供給機能に関するご注意
本ギターは弊社多機能プリアンプ AG-Stomp の電源供給機能には対応しており
ません。
電源供給機能を使用しますと、本ギターの内蔵プリアンプ内の回路が破損し、音
出力・チューナー機能等に支障をきたすおそれがあります。
※AG-Stomp に接続する場合は、電源供給機能を OFF(+9VSUPPLY スイッチを OFF)
にし、本ギターのバッテリーホルダーに電池を挿入した状態でお使いください。
電池を分解しない。
電池を火の中に入れない。
使い切りタイプの電池は、充
電しない。
指定以外の電池を使用しない。
複数の電池を使う場合、同じ
メーカーの同じ種類、同じ品
番の新しい電池を使用する。
電池はすべて＋ / －の極性表
示どおりに正しく入れる。
長時間使用しない場合や電池
を使い切った場合は、電池を
本体から抜いておく。
電池は子供の手の届くところ
に置かない。
電池を金属製のネックレスや
ヘアピン、コイン、鍵などと一
緒に持ち運んだり保管しない。
電池が液漏れした場合は、漏
れた液に触れない。万一液が
目や口に入ったり皮膚に付い
たりした場合は、すぐに水で
洗い流し、医師に相談してく
ださい。
Caution!
Regarding the AG-Stomp Guitar
Power Supply Function
This guitar is not compatible with the power supply function on the AG-Stomp
acoustic guitar preamplifier. Using the guitar power supply function on the AG-
Stomp can damage the guitar’s built-in preamplier resulting in abnormal sound
output, tuner operation, etc.
* Before connecting the guitar to the AG-Stomp, make sure that the AG-Stomp’s guitar power
supply function is switched OFF (switch OFF the +9V SUPPLY switch) and insert a battery
into the guitar’s battery holder.
・使用済みの電池は、各自治体で決められたルールに従って廃棄しましょう。
Attention !
À propos de la fonction d’alimentation
électrique de la guitare du AG-Stomp
La guitare n’est pas compatible avec la fonction d’alimentation électrique du pré-
amplicateur de guitare acoustique AG-Stomp. L’utilisation de cette fonction sur
l’AG-Stomp peut endommager le préamplicateur intégré de la guitare, ce qui nuit
à la qualité du son, au fonctionnement de l‘accordeur, etc.
* Avant de raccorder la guitare à l’AG-Stomp, assurez-vous que la fonction d‘alimentation élec-
trique de guitare de l‘AG-Stomp est désactivée (commutateur +9V SUPPLY en position OFF)
et introduisez une pile dans le porte-pile de la guitare.
Attenzione!
Funzione di alimentazione della
chitarra AG-Stomp
Questa chitarra non è compatibile con la funzione di alimentazione del preamplica-
tore per chitarra acustica YAMAHA AG-Stomp. Usando la funzione di alimentazione
della chitarra AG-Stomp si può danneggiare il preamplificatore incorporato della
chitarra, producendo suoni ed un funzionamento dell’accordatore anormali, ecc.
* Prima di collegare la chitarra all’AG-Stomp, controllare che la funzione di alimentazione della
chitarra AG-Stomp sia spenta (portando su OFF l’interruttore +9V SUPPLY) ed inserire una
batteria nel vano batteria della chitarra.
AVERTISSEMENT
Veillez à toujours observer les précautions élémentaires énumérées ci-après pour
éviter de graves blessures, voire la mort, en raison d'une électrocution, d'un court-
circuit, de dégâts, d'un incendie ou de tout autre risque. La liste de ces précautions
n'est pas exhaustive :
Piles
• Veillez à respecter les précautions détaillées ci-après. Le non respect de ces instruc-
tions risque de provoquer une explosion, un incendie ou une fuite du liquide des piles.
- N'altérez pas les piles et n'essayez pas de les démonter.
- Ne jetez pas les piles au feu.
- Ne tentez pas de recharger une pile non rechargeable.
- Gardez les piles éloignées des objets métalliques tels que les colliers, les épingles à
cheveux, les pièces de monnaie ou les clés.
- Utilisez uniquement le type de pile spécifié.
- Veillez à utiliser des piles neuves, de type et de modèle identiques, issues du même
fabricant.
- Prenez soin de respecter la polarité (+/-) lors de la mise en place des piles.
- Lorsque les piles sont épuisées ou en cas de non-utilisation de l'instrument pendant
une durée prolongée, retirez les piles de l'instrument.
• Conservez les piles hors de portée des enfants car ceux-ci risquent de les avaler.
• En cas de fuite du liquide des piles, évitez tout contact avec ce liquide. En cas de contact
avec les yeux, la bouche ou la peau, rincez immédiatement à l'eau claire et consultez un
médecin. Le liquide présent dans la pile est corrosif et peut provoquer la cécité ou des
brûlures chimiques.
Veiller à éliminer les piles usagées selon les réglementations locales.
Vorsicht!
Wichtiger Hinweis zur AG-Stomp-
Stromversorgung für Gitarren
Diese Gitarre ist nicht mit der Stromversorgungsfunktion des Akustik-Gitarren-
Vorverstärkers AG-Stomp kompatibel. Bei Anschluss an die Stromversorgung des
AG-Stomp kann der interne Vorverstärker der Gitarre Schaden nehmen, was anor-
malen Klang und Störungen der Stimmgerätfunktion zur Folge hat.
* Bevor Sie die Gitarre anschließen, schalten Sie den AG-Stomp aus (+9V SUPPLY-Schalter auf
„OFF“) und legen eine Batterie in den Batteriehalter der Gitarre ein.
¡Precaución!
Acerca de la función de
alimentación del AG-Stomp
Esta guitarra no es compatible con la función de alimentación del preamplicador
para guitarra acústica AG-Stomp. El empleo de la función de alimentación de guita-
rra del AG-Stomp puede causar daños en el preamplicador para guitarra incorpo-
rado y producir anormalidades en la salida de sonido, operación del anador, etc.
* Antes de conectar la guitarra al AG-Stomp, asegúrese de que la función de alimentación
de guitarra del AG-Stomp esté desactivada (OFF) (desconecte (OFF) el interruptor +9V
SUPPLY) e inserte una pila en el compartimiento de la pila de la guitarra.
Внимание!
Относительно функции источника питания гитарного процес-
сора AG-Stomp (процессор эффектов для акустических гитар)
Данная гитара несовместима с функцией источника питания на акустическом гитарном
предусилителе процессора AG-Stomp. Использование функции источника питания гитары на
процессоре AG-Stomp может повредить встроенный предусилитель гитары и привести к не
-
нормальному выводу звукового сигнала, нарушению работы тюнера, и т.п.
* Перед подсоединением гитары к процессору AG-Stomp убедитесь в том, что функция источника
питания гитарного процессора AG-Stomp выключена (переключатель ВЫКЛ установлен в поло
-
жение +9V SUPPLY), а затем вставьте батарею в держатель батареи гитары.
WARNUNG
Beachten Sie stets die nachstehend aufgelisteten Vorsichtsmaßnahmen, um mögliche
schwere Verletzungen oder sogar tödliche Unfälle infolge eines elektrischen Schlags, von
Kurzschlüssen, Feuer oder anderen Gefahren zu vermeiden. Zu diesen Vorsichtsmaßnahmen
gehören die folgenden Punkte, die jedoch keine abschließende Aufzählung darstellen:
Batterien
• Beachten Sie die folgenden Vorsichtsmaßnahmen. Bei Missachtung der Maßnahmen
könnte es zu einer Explosion oder einem Brand kommen oder Batterieflüssigkeit auslaufen.
- Manipulieren Sie Batterien nicht und nehmen Sie sie nicht auseinander.
- Werfen Sie Batterien nicht ins Feuer.
- Versuchen Sie niemals, Batterien aufzuladen, die nicht zum mehrfachen Gebrauch
und Nachladen vorgesehen sind.
- Bewahren Sie die Batterien nicht zusammen mit metallischen Gegenständen wie
Halsketten, Haarnadeln, Münzen und Schlüsseln auf.
- Verwenden Sie ausschließlich den angegebenen Batterietyp.
- Verwenden Sie neue Batterien, die alle vom gleichen Typ, Modell und Hersteller sind.
- Vergewissern Sie sich stets, dass alle Batterien gemäß den Polaritätskennzeichnun-
gen (+/-) eingelegt sind.
- Wenn die Batterien leer sind oder Sie das Instrument längere Zeit nicht nutzen wer-
den, entnehmen Sie die Batterien aus dem Instrument.
• Halten Sie Batterien von kleinen Kindern fern, die sie versehentlich verschlucken könnten.
• Wenn die Batterien leck sind, vermeiden Sie jede Berührung mit der ausgetretenen Flüs-
sigkeit. Wenn die Batterieflüssigkeit mit Augen, Mund oder Haut in Kontakt kommt, bitte
sofort mit Wasser auswaschen und einen Arzt aufsuchen. Batterieflüssigkeit ist ätzend und
kann zum Verlust des Augenlichts oder zu chemischen Verbrennungen führen.
Achten Sie darauf, dass gebrauchte Batterien den geltenden Bestimmungen gemäß
entsorgt werden.
ПРЕДУПРЕЖДЕНИЕ
Во избежание получения серьезных травм вплоть до наступления смерти от удара
электрическим током, а также во избежание короткого замыкания, повреждения
оборудования, пожара и других инцидентов, всегда соблюдайте основные правила
безопасности, перечисленные далее. Они включают принятие следующих мер (не
ограничиваясь ими):
Батарея
• Выполняйте указанные ниже меры предосторожности. Несоблюдение этих мер может
привести к взрыву, возгоранию, перегреву или вытеканию электролита из батарей.
- Не портите умышленно и не разбирайте батареи.
- Не бросайте батареи в огонь.
- Не пытайтесь перезаряжать батареи, не предназначенные для перезарядки.
- Хранитебатареиотдельноотметаллическихпредметов,такихкакожерелья,заколки, монеты
и ключи.
- Используйте только батареи указанного типа.
- При применении новых батарей устанавливайте батареи одинакового типа и одинаковой
модели, изготовленные одним производителем.
- Обязательно устанавливайте батареи согласно маркировке, соблюдая полярность.
- При разрядке батарей или если инструмент не будет использоваться в течение
длительного времени, выньте их из инструмента во избежание вытекания электролита.
• Храните батареи в недоступном для детей месте.
• Если батареи все же протекли, избегайте контакта с вытекшим электролитом. В случае
попадания электролита в глаза, рот или на кожу, немедленно смойте электролит водой и
обратитесь к врачу. Электролит, используемый в батареях, – это агрессивное вещество,
способное вызвать потерю зрения или химические ожоги.
Утилизацию использованных батарей необходимо выполнять в соответствии с
действующим местным законодательством.
ADVERTENCIA
Siga siempre las precauciones básicas detalladas a continuación para prevenir la
posibilidad de lesiones graves, o incluso la muerte, por descargas eléctricas, corto-
circuitos, daños, incendios u otros peligros. Estas precauciones incluyen, aunque
no de forma exclusiva, las siguientes:
Pilas
• Tenga en cuenta las advertencias que se indican a continuación. Si no fuera así, podría
producirse una explosión, un incendio, un recalentamiento o fugas.
- No manipule ni desmonte las pilas.
- No tire pilas al fuego.
- No intente recargar pilas que no sean recargables.
- Mantenga las pilas separadas de objetos metálicos como collares, horquillas, mone-
das y llaves.
- Utilice el tipo de pila especificado.
- Utilice pilas nuevas, todas del mismo tipo, del mismo modelo y del mismo fabricante.
- Asegúrese siempre de que todas las pilas estén colocadas conforme a las marcas de
polaridad +/-.
- Cuando se agoten las pilas o no se vaya a utilizar el instrumento durante mucho
tiempo, quite las pilas del instrumento.
• No deje las pilas cerca de niños pequeños que puedan tragarlas accidentalmente.
• Si las pilas tienen alguna fuga, evite el contacto con el fluido derramado. Si el fluido de
la pila entra en contacto con los ojos, la boca o la piel, lávese inmediatamente con agua
y consulte a un médico. El fluido de las pilas es corrosivo y puede causar pérdida de
visión o quemaduras químicas.
Asegúrese de desechar las pilas usadas de acuerdo con la normativa local.
ADVERTÊNCIA
Sempre observe as precauções básicas descritas a seguir para evitar a possibilidade
de sérios ferimentos ou mesmo a morte decorrentes de um choque elétrico, curto-
circuito, danos, incêndio ou outros perigos. Estas precauções incluem, entre outros:
Pilha
• Siga as precauções abaixo. Deixar de fazer isso pode provocar uma explosão, incêndio,
sobreaquecimento ou vazamento do fluido das pilhas.
- Não modifique nem desmonte pilhas.
- Não elimine pilhas ao fogo.
- Não tente recarregar pilhas que não foram projetadas para serem carregadas.
- Mantenha as pilhas separadas de objetos metálicos como colares, grampos de
cabelo, moedas e chaves.
- Use apenas o tipo de pilha especificado.
- Use pilhas novas, todas do mesmo tipo, mesmo modelo, e feitas pelo mesmo fabri-
cante.
- Certifique-se sempre de instalar todas as pilhas em conformidade com as marcações
de polaridade +/–.
- Quando as pilhas se esgotarem, ou se você não for usar o produto durante um longo
período de tempo, retire as pilhas do instrumento.
• Não transporte nem guarde as pilhas com objetos metálicos como colares, grampos de
cabelo, moedas ou chaves.
• Se as pilhas vazarem, evite o contato com o fluido vazado. Se o fluido de uma pilha entrar
em contato com seus olhos, boca ou pele, lave a parte afetada imediatamente com água
e procure um médico. O fluido das pilhas é corrosivo e pode provocar a perda da visão ou
queimaduras químicas.
Certifique-se de eliminar pilhas usadas de acordo com os regulamentos locais.
Atenção!
Sobre a função de fornecimento de energia do
pré-amplificador de violão acústico AG-Stomp
Este violão não é compatível com a função de fornecimento de energia do pré-
amplicador de violão acústico AG-Stomp. Usar a função de fornecimento de en-
ergia para violão no pré-amplicador AG-Stomp pode danicar o pré-amplicador
integrado do violão, resultando numa saída anormal do som, operação incorreta
do anador, etc.
* Antes de conectar o violão ao pré-amplicador AG-Stomp, certique-se de que a função de
fornecimento de energia para violão do pré-amplicador AG-Stomp esteja desativada (desligue
o interruptor +9V SUPPLY) e coloque uma pilha no porta-pilha do violão.
警告！
关干 AG-Stomp 吉他的电源功能
本吉他不兼容 AG-Stomp 原音吉他前置放大器上的电源功能。
使用 AG-Stomp 上的吉他电源功能会损坏吉他的内置前置放大
器，从而导致声音输出，调谐器运转异常等后果。
*将吉他连接到 AG-Stomp 之前，请确认已关闭 AG-Stomp 的吉他
电源功能 ( 将＋９VSUPPLY 开关置干 OFF)，并且已将电池插入
吉他的电池舱。
警告
为了避免因触电、短路、损伤、火灾或其它危险可能导致的严重
受伤甚至死亡，请务必遵守下列基本注意事项。这些注意事项包
括但不限于下列情况 ：
电池
•
请遵照以下注意事项。否则，可能会导致爆炸、火灾、过热或
电池液泄漏。
- 切勿玩弄或拆卸电池。
- 请勿将电池丢弃到火中。
- 请勿试图对非充电电池进行充电。
- 请使电池远离项链、发夹、硬币和钥匙等金属物件。
- 只能使用规定的电池类型。
- 请使用相同类型、相同型号以及由相同厂商生产的新电池。
- 装入电池时，请务必使其正负极与 +/- 极标记保持一致。
-
当电池用尽，或者长时间未使用本乐器，请从本乐器中取出电池。
•
请将电池放置在小孩够不到的地方以免其误吞。
•
万一电池发生泄漏，请勿接触泄漏的电解液。万一电解液进入
眼睛、嘴，或接触到皮肤，请立即用水冲洗并去看医生。电解
液具有腐蚀性，可能致视力丧失或化学灼伤。
请务必根据当地的规定处理废弃的电池。
주의 !
AG- 스톰프 기타 전원 공급 기능에 관해서
본 기타는 AG- 스톰프 어코스틱 기타 프리앰프의 전원 공급 기능과 호환하지 않습
니다 . AG- 스톰프에서 기타 전원 공급 기능을 사용하면 기타의 내장 프리앰프를 손
상시켜서 비정상적인 사운드 출력이나 튜너 조작 등을 유발합니다 .
* AG- 스톰프에 기타를 연결하기 전에 AG- 스톰프의 기타 전원 공급 기능이 꺼진 것을 확
인하고 (+9V SUPPLY 스위치를 끕니다 ), 기타의 배터리 홀더에 배터리를 삽입해 주십
시오 .
경고
아래에 열거되어 있는 기본 주의사항을 반드시 준수하여 감전 , 누전 , 손상 , 화
재 및 기타 위험으로 인해 부상 및 사망이 발생할 가능성을 줄이시기 바랍니
다 . 다음과 같은 주의사항들이 있으나 이 사항들에 국한되는 것은 아 닙니다 .
배터리 최적화
•
아래의 안전 주의사항을 준수하십시오 . 그렇지 않으면 폭발 , 화재가 발생하거나
배터리 액이 누출될 수 있습니다 .
- 배터리를 임의로 조작하거나 분해하지 마십시오 .
- 배터리를 불에 넣지 마십시오 .
- 일회용 배터리는 재충전하지 마십시오 .
- 배터리를목걸이 , 머리핀 , 동전 , 열쇠등과같은금속물체와가까이 두지 마십시오 .
- 지정된 배터리 만 사용하십시오 .
- 새 베터리를 사용할 경우 같은 제조업체에서 만든 동일한 형식의 동일한 모델
을 사용하십시오 .
- +/- 극성 표시에 맞춰 배터리를 정확하게 삽입하십시오 .
- 배터리가 완전히 소모된 경우 또는 악기를 장시간 사용하지 않는 경우에는 악기
에서 배터리를 빼십시오 .
•
사고로 삼킬 수도 있으므로 배터리는 유아의 손이 닿지 않는 곳 에 보관하십시오 .
•
배터리 액이 누출된 경우 누출된 액체가 손에 닿지 않도록 하십 시오 . 배터리 액이
누출되어 눈이나 입 , 피부에 닿은 경우에는 즉시 물로 씻은 후 의사와 상담하십시오 .
배터리 액은 부식성이기 때문에 시력 상실 및 화학적 화상을 야기할 수 있습니다 .
배터리는 반드시 해당 지역의 법규에 따라 폐기하십시오 .
产品中有害物质的名称及含量
部件名称
有害物质
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr(VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
吉他主机
× ○ ○ ○ ○ ○
电装 × ○ ○ ○ ○ ○
本表格依据 SJ/T 11364 的规定编制。
○ ：表示该有害物质在该部件所有均质材料中的含量均在 GB/T
26572 规定的限量要求以下。
× ：表示该有害物质至少在该部件的某一均质材料中的含量超
出 GB/T 26572 规定的限量要求。
乐器背面或里面的序列号中表示了生产日期
序列号的显示示例
制造年份 ：首部的两个字母表示日历年份最后面的两位数字。
字母“H”到“P”分别表示“1”到“9”的数字，“0”由字
母 "Q" 表示。
制造月份 ：从一月到九月，以字母“H”到“P”分别表示 ,
十月至十二月的月份 , 以字母“X”到“Z”分别表示。
产品上显示了生产日期
制造年份
制造月份
该标记附加在出售到中华人民共和国的电子信息产品上。
环形中的数字表示的是环境保护使用期限的年数。
FCC INFORMATION (U.S.A.)
not occur in all installations. If this product is found to be the
source of interference, which can be determined by turning the
unit “OFF” and “ON”, please try to eliminate the problem by using
one of the following measures:
Relocate either this product or the device that is being affected
by the interference.
Utilize power outlets that are on different branch (circuit breaker
or fuse) circuits or install AC line lter/s.
In the case of radio or TV interference, relocate/reorient the an-
tenna. If the antenna lead-in is 300 ohm ribbon lead, change the
lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this type
of product. If you can not locate the appropriate retailer, please
contact Yamaha Corporation of America, Electronic Service Divi-
sion, 6600 Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products distributed
by Yamaha Corporation of America or its subsidiaries.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
CAN ICES-3 (B)/NMB-3(B)
• This applies only to products distributed by Yamaha Canada Music Ltd.
• Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée. (can_b_01)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements. Modica-
tions not expressly approved by Yamaha may void your authority,
granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/
or another product use only high quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all installation
instructions. Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with
the requirements listed in FCC Regulations, Part 15 for Class
“B” digital devices. Compliance with these requirements provides
a reasonable level of assurance that your use of this product in
a residential environment will not result in harmful interference
with other electronic devices. This equipment generates/uses
radio frequencies and, if not installed and used according to the
instructions found in the users manual, may cause interference
harmful to the operation of other electronic devices. Compliance
with FCC regulations does not guarantee that interference will
Manual Development Group
© 2016 Yamaha Corporation
Published 08/2017
改版
PO-A0
-
1
-
2
-
3
-
4
-
5
dans d''autres langues
- italiano: Yamaha SYSTEM70 Manuale utente
- English: Yamaha SYSTEM70 User manual
- español: Yamaha SYSTEM70 Manual de usuario
- Deutsch: Yamaha SYSTEM70 Benutzerhandbuch
- русский: Yamaha SYSTEM70 Руководство пользователя
- português: Yamaha SYSTEM70 Manual do usuário
Documents connexes
-
Yamaha SYSTEM70 Manuel utilisateur
-
-
-
-
-
-
-
-
-