ATEN CL1000 Manuel utilisateur

LCD Console

CL1000M / CL1000N

User Manual

www.aten.com

CL1000M / CL1000N User Manual

ii

EMC Information

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE

STATEMENT: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at their own expense.

FCC Caution:

Any changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate this equipment.

Warning: Operation of this equipment in a residential environment could cause

radio interference.

Achtung: Der Gebrauch dieses Geräts in Wohnumgebung kann Funkstörungen

verursachen.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation.

KCC Statement

RoHS

This product is RoHS compliant.

CL1000M / CL1000N User Manual

iii

User Information

Online Registration

Be sure to register your product at our online support center:

Telephone Support

For telephone support, call this number:

International http://eservice.aten.com

International 886-2-8692-6959

China 86-400-810-0-810

Japan 81-3-5615-5811

Korea 82-2-467-6789

North America 1-888-999-ATEN ext 4988

1-949-428-1111

CL1000M / CL1000N User Manual

iv

User Notice

All information, documentation, and specifications contained in this manual

are subject to change without prior notification by the manufacturer. The

manufacturer makes no representations or warranties, either expressed or

implied, with respect to the contents hereof and specifically disclaims any

warranties as to merchantability or fitness for any particular purpose. Any of

the manufacturer's software described in this manual is sold or licensed as is.

Should the programs prove defective following their purchase, the buyer (and

not the manufacturer, its distributor, or its dealer), assumes the entire cost of all

necessary servicing, repair and any incidental or consequential damages

resulting from any defect in the software.

The manufacturer of this system is not responsible for any radio and/or TV

interference caused by unauthorized modifications to this device. It is the

responsibility of the user to correct such interference.

The manufacturer is not responsible for any damage incurred in the operation

of this system if the correct operational voltage setting was not selected prior

to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS

CORRECT BEFORE USE.

A typical LCD (Liquid Crystal Display) monitor has millions of pixels. A dead

pixel refers to a pixel with a defect in its ability to display the correct color

output. It most often looks like a tiny black or white spot on your screen,

although it can be any other color. Since even a tiny dust particle on one of the

pixels during the manufacturing process or a slight bump during shipping can

create a dead pixel, the ISO 13406-2 norm defines 4 classes of acceptable

screens with dead pixels--Class 1 is the best; Class 4 is the worst. Almost all

manufacturers use Class 2 to establish their warranties, which allows a certain

amount of dead pixels to exist before they will replace the screen. Since the

manufacturers consider these screens to be acceptable under ISO

specifications, we cannot be responsible for replacement or warranty of the

TFT LCD panel.

CL1000M / CL1000N User Manual

v

Package Contents

CL1000M

The CL1000M package consists of:

 1 CL1000M 17" LCD Console with Standard Rack Mount Kit

 1 Custom KVM Cable Set

 1 Power Cord

 1 User Instructions*

CL1000N

The CL1000N package consists of:

 1 CL1000N 19" LCD Console with Standard Rack Mount Kit

 1 Custom KVM Cable Set

 1 Power Cord

 1 User Instructions*

Check to make sure that all the components are present and that nothing got

damaged during shipping. If you encounter a problem, contact your dealer.

Read this manual thoroughly and follow the installation and operation

procedures carefully to prevent any damage to the unit, and/or any of the

devices connected to it.

* Features may have been added to the CL1000M / CL1000N since this

manual was published. Please visit our website to download the most up-to-

date version.

Manual Date: 2020-11-04

All other brand names and trademarks are the registered property of their respective owners.

CL1000M / CL1000N User Manual

vi

Contents

EMC Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

RoHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

CL1000M. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

CL1000N. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

About this Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ix

Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ix

Chapter 1.

Introduction

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Switches and Computers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

CL1000M Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

CL1000M Rear View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

CL1000N Front View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

CL1000N Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Chapter 2.

Hardware Setup

Before you Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

CL1000M / CL1000N Standard Rack Mounting . . . . . . . . . . . . . . . . . . . . . 9

Optional Rack Mount Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

CL1000M / CL1000N Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Chapter 3.

Operation

CL1000M Opening the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Closing the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

CL1000N Opening the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Closing the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Operating Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

LCD OSD Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

LCD Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Adjustment Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Manufacturing Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

CL1000M / CL1000N User Manual

vii

Port ID Numbering & Port Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Appendix

Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Consignes de sécurité. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Général . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Montage sur bâti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

International. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

About SPHD Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

CL1000M / CL1000N User Manual

viii

About this Manual

This User Manual is provided to help you get the most from your CL1000M /

CL1000N system. It covers all aspects of installation, configuration and

operation. An overview of the information found in the manual is provided

below.

Chapter 1, Introduction, introduces you to the CL1000M / CL1000N

system. Its purpose, features and benefits are presented, and its front and back

panel components are described.

Chapter 2, Hardware Setup, provides step-by-step instructions for setting

up your installation, and explains some basic operation procedures.

Chapter 3, Operation, explains the fundamental concepts involved in

operating the CL1000M / CL1000N.

An Appendix, provides specifications and other technical information

regarding the CL1000M / CL1000N.

CL1000M / CL1000N User Manual

ix

Conventions

This manual uses the following conventions:

Product Information

For information about all ATEN products and how they can help you connect

without limits, visit ATEN on the Web or contact an ATEN Authorized

Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:

Monospaced Indicates text that you should key in.

[ ] Indicates keys you should press. For example, [Enter] means to

press the Enter key. If keys need to be chorded, they appear

together in the same bracket with a plus sign between them:

[Ctrl+Alt].

1. Numbered lists represent procedures with sequential steps.

♦ Bullet lists provide information, but do not involve sequential steps.

→ Indicates selecting the option (on a menu or dialog box, for

example), that comes next. For example, Start

→

Run means to

open the Start menu, and then select Run.

Indicates critical information.

International http://www.aten.com

North America http://www.aten-usa.com

CL1000M / CL1000N User Manual

x

This Page Intentionally Left Blank

1

Chapter 1

Introduction

Overview

The CL1000M / CL1000N is a LCD KVM console that features an integrated

17” (CL1000M) or 19” (CL1000N) LED-backlit LCD panel, full keyboard,

and touchpad in a 1U rack-mountable sliding housing. These models provide

convenient ‘at the rack’ console access to KVM switches already installed at

your site.

These models were developed in response to the enormous popularity of the

sliding console found on the CL1008 and CL1016 KVM switches. Those

switches are made up of two major modules: the front-end sliding KVM

Console module, and the back-end KVM Switch module.

The CL1000M / CL1000N is similar to the front-end Console module found on

the CL1008 and CL1016. Its purpose is to serve as the front end sliding console

for compatible KVM switches.

By only having to purchase the CL1000M / CL1000N, users who already have

a compatible KVM switch can take advantage of the space saving and

efficiency benefits of the sliding console module without the unnecessary

expense of having to purchase a model that includes a KVM switch module.

Setup is fast and easy. Simply use the KVM cable set supplied with this

package to link the CL1000M / CL1000N’s KVM port to the console port of

your KVM switch and you are ready to go.

CL1000M / CL1000N User Manual

2

Features

 Exclusive LED illumination light - designed by ATEN to illuminate the

keyboard and touchpad to allow visibility in low-light conditions

 Integrated KVM console with a 17”(CL1000M) or 19" (CL1000N) LED-

backlit LCD monitor in a sliding housing with top and bottom clearance

for smooth operation in a 1U high system rack

 LCD module rotates up to 115

o

for a more comfortable viewing angle

 Standard rack mount kit included – optional Easy Rack Mounting (single

person installation) rack mount kit available (requires separate purchase)

 Compatible with most KVM switches

 Internal power supply

 High video resolution:

 Up to 1280 x 1024 @75Hz

 Supports DDC, DDC2, DDC2B

 DDC emulation of the LCD monitor

 Video settings of attached computers are automatically adjusted for

optimal output to the LCD monitor

Chapter 1. Introduction

3

Requirements

Switches and Computers

 The CL1000M / CL1000N supports most KVM switches that have PS/2

console port connectors. If you are unsure whether your switch is

supported or not, check with your dealer.

 The integrated LCD monitor's maximum resolution is 1280 x 1024 @

75 Hz. Make sure that none of the resolution settings of the connected

computers exceed the LCD monitor's maximum resolution.

Cables

For optimum signal integrity and to simplify the layout, we strongly

recommend that you use the high quality custom cable set provided with this

package. Different length cable sets, described in the table below, can be

purchased from your dealer.

Operating Systems

Supported operating systems are shown in the table, below:

* This operating system does not support USB.

Function Length Part Number

KVM switch to computer PS/2 1.2 m

1.8 m

3.0 m

6.0 m

2L-5201P

2L-5202P

2L-5702P

2L-5203P

2L-5206P

USB 1.8 m

3.0 m

5.0 m

6.0 m

2L-5202UP

2L-5203UP

2L-5205UP

2L-5206UP

OS Version

Windows 2000 and higher

Linux RedHat 7.1–7.3, 8.0, 9.0, Fedora Core 2–4

SuSE 8.2, 9.3, 10

Mandriva (Mandrake) 9, 2005 Limited Edition, 2006

UNIX AIX 4.3, 5L

FreeBSD 4.2, 4.5

Novell Netware 5.0*, 6.0

CL1000M / CL1000N User Manual

4

Components

CL1000M Front View

No. Component Description

1 Handle Pull to slide the KVM module out; push to slide the module in.

2 Slide Release In order to slide the console out, you must first release it by

moving this tab sideways. See page 15 for details on sliding

the console in and out.

3 LCD Display After sliding the KVM module out, flip up the cover to access

the LCD monitor.

4 LCD Controls The LCD On/Off switch is located here, as well as buttons to

control the position and picture settings of the LCD display.

See page 18, for details.

5 Keyboard Standard 105-key Keyboard.

6 Touchpad Standard Touch Pad.

7 Power LED Lights dark green to indicate that the unit is receiving power.

Chapter 1. Introduction

5

CL1000M Rear View

8 Rack Mounting

Brackets

The rack mounting brackets located at each corner of the unit

secure the chassis to a system rack.

9 Lock LEDs The Num Lock, Caps Lock, Scroll Lock LEDs are located

here.

10 Reset Switch Located to the right of the Lock LEDs. Press this recessed

switch in with a thin object to perform a system reset.

11 LED Illumination

Light

Press the Exit/Light pushbutton for two seconds to turn the

LED light On or Off. (Default: On)

No. Component Description

1 Power Socket This is a standard 3-prong AC power socket. The power cord

from your AC source plugs in here.

2 Power Switch This is a standard rocker switch that powers the unit On and

Off.

3 KVM Port The cable that links the CL1000M to the KVM switch plugs in

here.

Note: The shape of this SPHD connector has been

specifically modified so that only KVM cables designed to

work with this switch can plug in (see Cables, page 3, for

details).

1

2

3

CL1000M / CL1000N User Manual

6

CL1000N Front View

No. Component Description

1 Handle Pull to slide the KVM module out; push to slide the module in.

2 Slide Release In order to slide the console out, you must first release it by

moving this tab sideways. See page 15 for details on sliding

the console in and out.

3 LCD Display After sliding the KVM module out, flip up the cover to access

the 19” LCD monitor.

4 LCD Controls The LCD On/Off switch is located here, as well as buttons to

control the position and picture settings of the LCD display.

See page 18, for details.

5 Keyboard Standard 105-key Keyboard.

6 Touchpad Standard Touch Pad.

7 CPU LED Lights green to indicate that the unit is connected to the KVM

Switch port.

Chapter 1. Introduction

7

CL1000N Rear View

8 Rack Mounting

Brackets

The rack mounting brackets located at each corner of the unit

secure the chassis to a system rack.

9 Lock LEDs The Num Lock, Caps Lock, Scroll Lock LEDs are located

here.

10 LCD On / Off

Button

Push this button to turn the LCD monitor on and off. The

button lights when the LCD monitor is off.

Note: The light indicates that only the monitor is off, not the

attached KVM switch.

11 LED Illumination

Light

Press the Exit/Light pushbutton for two seconds to turn the

LED light ON or Off. (Default: On)

No. Component Description

1 Power Socket This is a standard 3-prong AC power socket. The power cord

from your AC source plugs in here.

2 KVM Port The cable that links the CL1000N to the KVM switch plugs in

here.

Note: The shape of this SPHD connector has been

specifically modified so that only KVM cables designed to

work with this switch can plug in (see Cables, page 3, for

details).

1

2

CL1000M / CL1000N User Manual

8

This Page Intentionally Left Blank

9

Chapter 2

Hardware Setup

Before you Begin

CL1000M / CL1000N Standard Rack Mounting

A standard rack mount kit is provided with your CL1000M / CL1000N. The kit

mounts the CL1000M in a rack with a depth of 42–72 cm or CL1000N in a rack

with a depth of 52–85 cm.

Note:  It takes two people to mount the console.

 The standard rack mounting kit does not include screws or cage

nuts. If you need additional screws or cage nuts, contact your rack

dealer.

1. Important safety information regardin

g the placement of this

device is provided on page 21. Please review it before proceeding.

2.

Make sure that power to all the devices

you will be connecting up

have been turned off. You must unplug the power cords of any

computers that have the Keyboard Power On function.

Left & Right L-shaped Brackets

Side Mounting

Bracket

CL1000M / CL1000N User Manual

10

To install the CL1000M / CL1000N using the Standard Rack Mount Kit,

follow the steps below:

1. Have one person position the unit in the rack and hold it steady. Have the

second person screw the front brackets to the rack.

2. While the first person still holds the unit in place, the second person slides

the left & right L-shaped brackets into the unit’s side mounting brackets

from the rear, installing four screws in the brackets to secure them in place.

3. After the L-shaped brackets are secured, tighten all the screws.

Allow at least 5.1 cm on each side for proper ventilation, and at least 12.7

cm at the back for the power cord and cable clearance.

La page charge ...

ATEN CL1000 Manuel utilisateur

ATEN CL1000 Manuel utilisateur

dans d''autres langues

Documents connexes