ATEN CL1016 Manuel utilisateur

LCD KVM Switch

CL1008 / CL1016

User Manual

www.aten.com

CL1008 / CL1016 User Manual

ii

EMC Information

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE

STATEMENT: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at their own expense.

FCC Caution:

Any changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate this equipment.

Warning: Operation of this equipment in a residential environment could

cause radio interference.

Achtung: Der Gebrauch dieses Geräts in Wohnumgebung kann

Funkstörungen verursachen.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation.

KCC Statement

RoHS

This product is RoHS compliant.

CL1008 / CL1016 User Manual

iii

User Information

Online Registration

Be sure to register your product at our online support center:

Telephone Support

For telephone support, call this number:

User Notice

All information, documentation, and specifications contained in this manual

are subject to change without prior notification by the manufacturer. The

manufacturer makes no representations or warranties, either expressed or

implied, with respect to the contents hereof and specifically disclaims any

warranties as to merchantability or fitness for any particular purpose. Any of

the manufacturer's software described in this manual is sold or licensed as is.

Should the programs prove defective following their purchase, the buyer (and

not the manufacturer, its distributor, or its dealer), assumes the entire cost of all

necessary servicing, repair and any incidental or consequential damages

resulting from any defect in the software.

The manufacturer of this system is not responsible for any radio and/or TV

interference caused by unauthorized modifications to this device. It is the

responsibility of the user to correct such interference.

The manufacturer is not responsible for any damage incurred in the operation

of this system if the correct operational voltage setting was not selected prior

to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS

CORRECT BEFORE USE.

International http://eservice.aten.com

International 886-2-8692-6959

China 86-400-810-0-810

Japan 81-3-5615-5811

Korea 82-2-467-6789

North America 1-888-999-ATEN ext 4988

1-949-428-1111

CL1008 / CL1016 User Manual

iv

Package Contents

Basic Package

The basic CL1008 or CL1016 package consists of:

 1 CL1008 or CL1016 with Standard Rack Mount Kit

 2 Custom KVM Cable Sets

 1 Power Cord

 1 Firmware Upgrade Cable

 1 Quick Start Guide

Check to make sure that all the components are present and that nothing got

damaged in shipping. If you encounter a problem, contact your dealer.

Read this manual thoroughly and follow the installation and operation

procedures carefully to prevent any damage to the unit, and/or any of the

devices connected to it.

* Features may have been added to the CL1008 / CL1016 since this manual

was printed. Please visit our website to download the most up-to-date version

of the manual.

CL1008 / CL1016 User Manual

v

Contents

EMC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

RoHS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Basic Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Product Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

1. Introduction

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Computers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

OS Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2. Hardware Setup

Before you Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Standard Rack Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Optional Rack Mount Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Single Stage Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Daisy Chain Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

3. Basic Operation

Opening the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Closing the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Operating Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Powering Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Powering Off and Restarting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

LCD OSD Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

The LCD Buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

LCD Adjustment Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Port ID Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Port Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Manual Port Switching. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Hot Plugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4. OSD Operation

CL1008 / CL1016 User Manual

vi

OSD Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Logging In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

OSD Main Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

OSD Main Screen Headings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

OSD Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

OSD Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

F1: GOTO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

F2: LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

F3: SET. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

F4: ADM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

F5: SKP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

F6: BRC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

F7: SCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

F8: LOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

5. Hotkey Operation

Hotkey Port Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Invoking Hotkey Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Exiting Hotkey Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Hotkey Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Hotkey Mode Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Selecting the Active Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Auto Scan Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Setting the Scan Interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Invoking Auto Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Pausing Auto Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Exiting AutoScan Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Skip Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Hotkey Beeper Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Hotkey Summary Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

6. The Firmware Upgrade Utility

Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Starting the Upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Upgrade Succeeded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Upgrade Failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Appendix

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Consignes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Général . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Montage sur bâti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

CL1008 / CL1016 User Manual

vii

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

CL1008 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

CL1016 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Connection Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

CL1008 – ACS1208A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

CL1008 – ACS1216A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

CL1016 – ACS1208A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

CL1016 – ACS1216A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Clear Login Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

OSD Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Dedicated Invocation Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

About SPHD Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

CL1008 / CL1016 User Manual

viii

About this Manual

This User Manual is provided to help you get the most from your CL1008 /

CL1016 system. It covers all aspects of installation, configuration and

operation. An overview of the information found in the manual is provided

below.

Chapter 1, Introduction, introduces you to the CL1008 / CL1016 system.

Its purpose, features and benefits are presented, and its front and back panel

components are described.

Chapter 2, Hardware Setup, describes how to set up your installation. The

necessary step –

from a basic single stage hookup to a complete 16 switch daisy

chained operation are provided.

Chapter 3, Basic Operation, explains the fundamental concepts involved

in operating the CL1008 / CL1016.

Chapter 4, OSD Operation, provides a complete description of the

CL1008 / CL1016’s OSD (on-screen display), and how to work with it.

Chapter 5, Hotkey Operation, details all of the concepts and procedures

involved in the Hotkey operation of your CL1008 / CL1016 installation.

Chapter 6, The Firmware Upgrade Utility, explains how to use this

utility to upgrade the CL1008 / CL1016's firmware with the latest available

versions.

An Appendix, provides specifications and other technical information

regarding the CL1008 / CL1016.

CL1008 / CL1016 User Manual

ix

Conventions

This manual uses the following conventions:

Product Information

For information about all ATEN products and how they can help you connect

without limits, visit ATEN on the Web or contact an ATEN Authorized

Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:

Monospaced Indicates text that you should key in.

[ ] Indicates keys you should press. For example, [Enter] means to

press the Enter key. If keys need to be chorded, they appear

together in the same bracket with a plus sign between them:

[Ctrl+Alt].

1. Numbered lists represent procedures with sequential steps.

♦ Bullet lists provide information, but do not involve sequential steps.

→ Indicates selecting the option (on a menu or dialog box, for

example), that comes next. For example, Start

→

Run means to

open the Start menu, and then select Run.

Indicates critical information.

International http://www.aten.com

North America http://www.aten-usa.com

CL1008 / CL1016 User Manual

x

This Page Intentionally Left Blank

1

Chapter 1

Introduction

Overview

The CL1008 / CL1016 Slideaway

TM

LCD KVM Switch series are control units

that allow access to multiple computers from a single keyboard, video, and

mouse (KVM) console. A single CL1008 or CL1016 can control up to 8 or 16

computers. As many as 15 additional KVM switches can be daisy chained to

the CL1008 / CL1016, so that up to 256 computers can all be controlled from

a single KVM console.

The CL1008 / CL1016 offers a space-saving, streamlined approach to KVM

switch technology by integrating a keyboard, LCD monitor, and touchpad in a

1U rack-mountable sliding housing. The LCD display is built into the cover;

the keyboard and touchpad are built into the base. Slide the KVM module

section out; flip the cover up; and you are ready to work. When finished, flip

the cover down and slide the KVM module away.

The CL1008 / CL1016 is built on a modular design. The KVM section can be

detached from the switch section for convenient maintenance and repair.

Your CL1008 / CL1016 investment is protected by an included Firmware

Upgrade Utility. You can stay current with the latest improvements to the

switch by downloading firmware update files from our website as they become

available, and using the utility to quickly and conveniently perform the

upgrade.

Setup is fast and easy; plugging cables into their appropriate ports is all that is

entailed. Because the CL1008 / CL1016 intercepts keyboard input directly,

there is no software to configure; no need to get involved in complex

installation routines; nor any need to be concerned with incompatibility

problems.

Access to any computer connected to the installation is easily accomplished

either by entering hotkey combinations from the keyboard, or by means of a

powerful, mouse driven, on-screen display (OSD) menu system. A convenient

Auto Scan feature also permits automatic scanning and monitoring of the

activities of all computers running on the installation one by one.

CL1008 / CL1016 User Manual

2

Features

 Exclusive LED illumination light - designed by ATEN to illuminate the

keyboard and touchpad to allow visibility in low-light conditions

 KVM console with 17" LED-backlit LCD monitor in a sliding housing –

top and bottom clearance for smooth operation in a 1U high system rack

 LCD module rotates up to 115

o

for a more comfortable viewing angle

 Standard rack mount kit included – optional Easy Rack Mounting (single

person installation) rack mount kit available (requires separate purchase)

 Daisy chain up to 15 additional units – control up to 128 (CL1008) or 256

(CL1016) computers

 No software required – convenient computer selection via hotkeys and

mouse driven intuitive on-screen display (OSD) menus

 Auto Scan feature for monitoring user-selected computers

 Broadcast support – commands from the keyboard can be broadcast to all

available computers on the installation

 Hot pluggable – add or remove computers without having to power down

the switch

 Two level password security – only authorized users view and control the

computers – up to four users plus an administrator with separate profiles

for each

 Video settings of attached computers are automatically adjusted for

optimal output to the LCD monitor

 Upgradable firmware

 Keyboard language support: English (US), English (UK), French,

German, German (Swiss), Hungarian, Italian, Japanese, Korean, Russian,

Spanish, Swedish and Traditional Chinese

1. Introduction

3

Requirements

Computers

The following equipment must be installed on each computer:

 A VGA, SVGA or multisync card

Note: The integrated LCD monitor's maximum resolution is

1280 x 1024 @ 75 Hz. Make sure that none of the computer

resolution settings exceed the LCD monitor's maximum resolution.

 6-pin Mini-DIN (PS/2 style) keyboard and mouse ports

Cables

Substandard cables may damage the connected devices or degrade overall

performance. For optimum signal integrity and to simplify the layout, we

strongly recommend that you use the high quality CS Custom Cable sets

described below:

Function Part Number Length

Daisy-chain Cables 2L-1700 0.6 m

2L-1701 1.8 m

2L-1703 3.0 m

2L-1705 5.0 m

2L-1715 15.0 m

KVM Switch to Computer 2L-5201P 1.2 m

2L-5202P 1.8 m

2L-5702P 1.8 m

2L-5203P 3.0 m

2L-5206P 6.0 m

2L-5202UP 1.8 m

2L-5203UP 3.0 m

2L-5205UP 5.0 m

2L-5206UP 6.0 m

CL1008 / CL1016 User Manual

4

OS Support

Components

Front View

OS Version

Windows 2000 or later

Linux RedHat 7.1–7.3, 8.0, 9.0, Fedora Core 2–4

SuSE 8.2, 9.3, 10

Mandriva (Mandrake) 9, 2005 Limited Edition, 2006

UNIX IBM AIX: 4.3, 5L

FreeBSD 4.2, 4.5

Novell Netware: 5.0, 6.0

Press the Exit/Light pushbutton for

two seconds to turn the LED light

ON or O. (Default: On)

EXI T I LIGHT

4

1

2

3

5

12

13

8

6

7

9

10

11

1. Introduction

5

No. Component Description

1 Handle Pull to slide the KVM module out; push to slide the module in

(see item 2 in this table).

2 Slide Release In order to slide the console out, you must first release it by

sliding these tabs to the inside. See page 17 for details on

sliding the console in and out.

3 LCD Display After sliding the KVM module out, flip up the cover to access

the LCD monitor.

4 LCD Controls The LCD On/Off switch is located here, as well as buttons to

control the position and picture settings of the LCD display.

See page 21 for details.

5 Port Selection

Pushbutton /

LEDs (8 for

CL1008, 16 for

CL1016)

Press the Port Selection Pushbuttons to bring the KVM focus

to the computer attached to its corresponding port. See

page 23 for details.

Two Port LEDs are built into the Port Switches. The one on

the left is the On Line LED; the one on the right is the

Selected Port LED:



An On Line LED lights ORANGE to indicate that the

computer attached to its corresponding port is up and

running.



A Selected LED lights GREEN to indicate that the

computer attached to its corresponding port has the KVM

focus. The LED is steady under normal conditions, but

flashes when its port is accessed under Auto Scan Mode

(see F7: SCAN, page 37).

6 Keyboard Standard mouse touchpad

7 Touchpad Standard 105-key keyboard

8LED

Illumination

Light

Press the Exit/Light pushbutton for two seconds to turn the

LED light ON or Off. (Default: On)

9 Power LED Lights DARK GREEN to indicate that the unit is receiving

power.

10 Rack Mounting

Brackets

The rack mounting brackets located at each corner of the unit

secure the chassis to a system rack.

11 Lock LEDs The Num Lock, Caps Lock, Scroll Lock LEDs are located

here.

12 Reset Switch Located to the right of the Lock LEDs. Press this recessed

switch in with a small object to perform a system reset.

CL1008 / CL1016 User Manual

6

13 Firmware

Upgrade

Section



Firmware Upgrade Port: The Firmware Upgrade Cable

that transfers the firmware upgrade data from the

administrator's computer to the CL1008 / CL1016 plugs

into this RJ-11 connector.



Firmware Upgrade Switch: During normal operation this

switch should be in the NORMAL position. (See p. 45 for

firmware upgrading details.)

No. Component Description

1. Introduction

7

Rear View

Note: The CL1016 is pictured above. The CL1008 rear panel is the same as

that of the CL1016, except that it has 8 KVM ports instead of 16.

No. Component Description

1 Daisy Chain Port When daisy chaining units, the cable plugs in here.

2KVM Port

Section

The cables that link to the computers plug in here.

Note: The shape of these SPHD connectors has been

specifically modified so that only KVM cables designed to

work with this switch can plug in (see the Cables section on

page 3, for details). Do NOT attempt to use ordinary 15 pin

VGA connector cables to link these ports to the computers.

3 Power Socket This is a standard 3-prong AC power socket. The power cord

from an AC source plugs in here.

4 Power Switch This standard rocker switch powers the unit on and off.

1

2

3

4

CL1008 / CL1016 User Manual

8

This Page Intentionally Left Blank

9

Chapter 2

Hardware Setup

Before you Begin

Standard Rack Mounting

A standard rack mounting kit is provided with your CL1008 / CL1016. The kit

enables the switch to be mounted in rack with a depth of 42.0–82.0 cm.

Note:  It takes two people to mount the console.

 The standard rack mounting kit does not include screws or cage

nuts. If you need additional screws or cage nuts, contact your rack

dealer.

1. Important safety information regarding the placement of this

device is provided on page 51. Please review it before proceeding.

2. Make sure that power to all the devices you will be connecting up

have been turned off. You must unplug the power cords of any

computers that have the Keyboard Power On function.

Left & Right L-shaped Brackets

Side Mountng

Brackets

CL1008 / CL1016 User Manual

10

To rack mount the switch, do the following:

1. Have one person position the unit in the rack and hold it steady. Have the

second person screw the front brackets to the rack.

2. While the first person still holds the unit in place, the second person slides

the left & right L-shaped brackets into the unit’s side mounting brackets

from the rear, installing four screws in the brackets to secure them in place.

3. After the L-shaped brackets are secured, tighten all the screws.

Allow at least 5.1 cm on each side for proper ventilation, and at least 12.7

cm at the back for the power cord and cable clearance.

La page charge ...

ATEN CL1016 Manuel utilisateur

Ce manuel convient également à

ATEN CL1016 Manuel utilisateur

dans d''autres langues

Documents connexes