KitchenAid KDRS407VBU01 Guide d'installation
- Catégorie
- Cuisinières
- Taper
- Guide d'installation
Ce manuel convient également à
INSTALLATION INSTRUCTIONS
CommerCial-Style Dual Fuel ConveCtion rangeS
30"(76.2Cm),36"(91.4Cm)anD48" (121.9 Cm)
For residential use only
INSTRUCTIONS D’INSTALLATION
CuiSinièreS à ConveCtion à Double CombuStible
DetypeCommerCial
30"(76,2Cm),36"(91,4 Cm) et 48" (121,9 Cm)
Pour utilisation résidentielle uniquement
Table of Contents/Table des matières
W11090456A www.kitchenaid.com (U.S.A.) www.kitchenaid.ca (Canada)
RANGE SAFETY .............................................................................2
INSTALLATION REQUIREMENTS .................................................4
Tools and Parts ............................................................................. 4
Location Requirements ................................................................6
Water Filtration System Location Requirements .........................8
Water Supply Requirements ........................................................8
Electrical Requirements – U.S.A. Only .........................................9
Electrical Requirements – Canada Only ....................................10
Gas Supply Requirements .........................................................10
INSTALLATION INSTRUCTIONS ................................................. 12
Unpack the Range .....................................................................12
Install Optional Backguard .........................................................13
Install Anti-Tip Bracket ...............................................................13
Electrical Connection – U.S.A. Only ..........................................14
Install Water Filtration System ...................................................15
Make Gas Connection ...............................................................17
Verify Anti-Tip Bracket Location ................................................17
Level Range ................................................................................18
Install Grill Grease Trays .............................................................18
Install Griddle .............................................................................19
Electronic Ignition System .........................................................19
Reinstall Kick Plate .....................................................................21
Complete Installation .................................................................21
GAS CONVERSIONS ....................................................................22
Propane Gas Conversion ...........................................................22
Natural Gas Conversion .............................................................24
SÉCURITÉ DE LA CUISINIÈRE ...................................................27
EXIGENCES D’INSTALLATION ...................................................29
Outillage et pièces ......................................................................29
Exigences d’emplacement .........................................................31
Exigences d’emplacement du système de filtration de l’eau ....33
Spécifications de l’alimentation en eau .....................................33
Spécifications de l’installation électrique ..................................34
Spécifications de l’alimentation en gaz .....................................34
INSTRUCTIONS D’INSTALLATION .............................................36
Déballage de la cuisinière ..........................................................36
Installation du dosseret facultatif ...............................................37
Installation de la bride antibasculement ....................................37
Install Water Filtration System ...................................................38
Raccordement au gaz ................................................................39
Vérification de l’emplacement de la bride antibasculement .....40
Réglage de l’aplomb de la cuisinière .........................................40
Installation des plateaux à graisse du gril ..................................41
Installation de la plaque à frire ...................................................42
Système d’allumage électronique..............................................42
Réinstallation du garde-pieds ....................................................44
Achever l’installation ..................................................................44
CONVERSIONS POUR CHANGEMENT DE GAZ ......................45
Conversion pour l’alimentation au propane ..............................45
Conversion pour l’alimentation au gaz naturel ..........................47
IMPORTANT:
Save for local electrical inspector’s use.
Installer: Leave installation instructions with the homeowner.
Homeowner: Keep installation instructions for future reference.
IMPORTANT :
À conserver pour consultation par l’inspecteur local des installations électriques.
Installateur : Remettre les instructions d’installation au propriétaire.
Propriétaire : Conserver les instructions d’installation pour référence ultérieure.
2
RANGE SAFETY
WARNING: If the information in these instructions is not followed exactly, a fire or
explosion may result causing property damage, personal injury or death.
– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
– WHAT TO DO IF YOU SMELL GAS:
•
Do not try to light any appliance.
•
Do not touch any electrical switch.
•
Do not use any phone in your building.
•
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
•
If you cannot reach your gas supplier, call the fire department.
– Installation and service must be performed by a qualified installer, service agency or
the gas supplier.
WARNING: Gas leaks cannot always be detected by smell.
Gas suppliers recommend that you use a gas detector approved by UL or CSA.
For more information, contact your gas supplier.
If a gas leak is detected, follow the “What to do if you smell gas” instructions.
3
IMPORTANT: Do not install a ventilation system that blows air downward toward this gas cooking appliance. This type of
ventilation system may cause ignition and combustion problems with this gas cooking appliance resulting in personal injury or
unintended operation.
In the State of Massachusetts, the following installation instructions apply:
■ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gas fitter qualified or licensed by
the State of Massachusetts.
■ Acceptable Shut-off Devices: Gas Cocks and Ball Valves installed for use shall be listed.
■ A flexible gas connector, when used, must not exceed 4 feet (121.9 cm).
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation instructions.
Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.
Re-engage the anti-tip bracket if the range is moved.
Do not operate range without anti-tip bracket installed and engaged.
Failure to follow these instructions can result in death or serious burns to children and adults.
Anti-Tip
Bracket
To verify the anti-tip bracket is installed and engaged:
• Slide range forward.
• Look for the anti-tip bracket securely attached to floor or wall.
• See installation instructions for details.
Range Foot
WARNING
Slide range back so rear range foot is under anti-tip bracket.•
4
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
Tools Needed
For Propane/Natural Gas Conversions
Pipe wrench Adjustable wrench or
5/8" (16 mm) wrench
1/8" x 4
1
/
4
"
(3.2 mm x 108 mm)
flat‑blade screwdriver
#2 Phillips screwdriver
Drill 3/8" (95 mm) drive ratchet 15/16" (24 mm)
combination wrench
Pliers
Level Tubing cutter 1/4" (6.4 mm), 3/8" (9.5 mm),
5/16" (7.9 mm) nut drivers
Marker or pencil
3/16" (4.8 mm) carbide tip
masonry bit
1/8" (3.2 mm) drill bit Pipe‑joint compound
resistant to Propane gas
Noncorrosive leak‑detection
solution
Tape measure
1/2" (13 mm) deep‑well
socket
Adjustable wrench 7 mm nut driver Masking tape
5
Parts Supplied
Check that all parts are included.
■ Anti-tip bracket kit
NOTE: Anti-tip bracket must be securely mounted to
subfloor. Thickness of flooring may require longer screws
to anchor bracket to subfloor. Longer screws are available
from your local hardware store. See the “Install Anti-Tip
Bracket” section.
■ Gas pressure regulator
■ Burner grates
■ Burner bases and burner caps
■ Grill grate (on grill models)
■ Wave tray (on grill models)
■ Flame spreader (on grill models)
■ Burner assembly (on grill models)
■ Grease trays (2) (on grill models)
■ Griddle drip tray (on griddle models)
■ Grill drip tray (on grill models)
■ Island trim
■ Propane orifice package (W10393255)
■ Conversion label (W10839411)
NOTE: The cooktop is manufactured for use with Natural gas.
To convert to Propane gas, see the “Gas Conversions” section.
Additional Parts Supplied on Steam‑Assist Models
■ Model W10049700 water filter kit
■ 1/4" (6.4 mm) to 1/4" (6.4 mm) water supply union
Parts Needed
■ Power supply cord kit:
■ 30" (76.2 cm) and 36" (91.4 cm) models: A UL Listed
40-amp power supply cord kit
■ 48" (121.9 cm) models: A UL Listed 50-amp power
supply cord kit marked for use with nominal 1
3
/
8
"
(3.5 cm) diameter connection openings
■ A UL Listed strain relief
■ UL Listed wire connectors
■ All models must be installed with a backguard if installing
at zero clearance to a combustible back wall surface such
as drywall. Alternatively, zero clearance to a back wall is
acceptable provided the surface of the entire back wall
above the range and below the hood is covered with a
non-combustible material such as tile or stainless steel.
See “Cabinet Dimensions” in the “Location Requirements”
section for installation requirements.
■ 30" (76.2 cm) Adjustable Backguard
Order Part Number 8285148
■ 36" (91.4 cm) Adjustable Backguard
Order Part Number 8284756
■ 48" (121.9 cm) Adjustable Backguard
Order Part Number 8284755
■ 9" (22.9 cm) Backguard for 30" (76.2 cm) Ranges
Order Part Number W10115773
■ 9" (22.9 cm) Backguard for 36" (91.4 cm) Ranges
Order Part Number W10115776
■ 9" (22.9 cm) Backguard for 48" (121.9 cm) Ranges
Order Part Number W10115777
■ 22" (55.9 cm) Backguard with Shelf for 30"
(76.2 cm) Ranges
Order Part Number W10225950
■ 22" (55.9 cm) Backguard with Shelf for 36"
(91.4 cm) Ranges
Order Part Number W10225949
■ 22" (55.9 cm) Backguard with Shelf for 48"
(121.9 cm) Ranges
Order Part Number W10225948
To order, see the “Assistance or Service” section of the Use
and Care Guide.
Additional Parts Needed on Steam‑Assist Models
■ Tubing staples/retainers
■ 1/4" (6.4 mm) outer diameter (O.D.) flexible
codes-approved water supply tubing
(to make water connection)
■ Water connection device (to connect 1/4" (6.4 mm) O.D.
tubing to water source). Check local codes for type of
connection required.
Check local codes and consult gas supplier. Check existing gas
supply and electrical supply. See the “Electrical Requirements”
and “Gas Supply Requirements” sections.
It is recommended that all electrical connections be made by
a licensed, qualified electrical installer.
High Altitude Conversion
To convert the cooktop for elevations above 6,560 ft (1,999.5 m),
order a High Altitude Conversion Kit.
■ Part Number W10394296: Propane gas high altitude
■ Part Number W10394295: Natural gas high altitude
To order, see the “Assistance or Service” section of the Use
and Care Guide.
A
B
A. Anti-tip bracket
B. #8-18 x 1" (2.5 cm) Phillips head screws (4)
6
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
Do not obstruct flow of combustion and ventilation air.
■ It is the installer’s responsibility to comply with installation
clearances specified on the model/serial/rating plate. The
model/serial/rating plate is located under the console on
the right-hand side.
■ It is recommended that a 600 CFM (17.0 m
3
/hr) or larger
range hood be installed above the range.
■ It is not recommended that a microwave hood combination
be mounted above the range.
■ Recessed installations must provide complete enclosure
of the sides and rear of the range.
■ All openings in the wall or floor where range is to be installed
must be sealed.
■ Do not seal the range to the side cabinets.
■ Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.
■ The anti-tip bracket must be installed. To install the anti-tip
bracket shipped with the range, see the “Install Anti-Tip
Bracket” section.
■ Grounded electrical supply is required. See the “Electrical
Requirements” section.
■ Proper gas supply connection must be available. See the
“Gas Supply Requirements” section.
■ Contact a qualified floor covering installer to check that
the floor covering can withstand at least 200°F (93°C). Use
an insulated pad or 1/4" (64 mm) plywood over carpet and
under range if installing range over carpeting.
IMPORTANT: To avoid damage to your cabinets, check with
your builder or cabinet supplier to make sure that the materials
used will not discolor, delaminate, or sustain other damage. This
oven has been designed in accordance with the requirements
of UL and CSA International and complies with the maximum
allowable wood cabinet temperatures of 194°F (90°C).
Mobile Home — Additional Installation Requirements
The installation of this range must conform to the Manufactured
Home Construction and Safety Standard, Title 24 CFR,
Part 3280 (formerly the Federal Standard for Mobile Home
Construction and Safety, Title 24, HUD Part 280). When such
standard is not applicable, use the Standard for Manufactured
Home Installations, ANSI A225.1/NFPA 501A or local codes.
In Canada, the installation of this range must conform with
the current standards CAN/CSA-A240-latest edition or with
local codes.
Mobile Home Installations Require:
When this range is installed in a mobile home, it must be
secured to the floor during transit. Any method of securing the
range is adequate as long as it conforms to the standards listed
above.
Product Dimensions
30" (76.2 cm) models
36" (91.4 cm) models
D
C
A
B
E
A. Optional backguard may be installed.
B. 27
3
/
4
" (70.5 cm) depth with control panel (See NOTE.)
C. 35
3
/
4
" (90.8 cm) cooktop height when sitting on the wheels
D. 30" (76.2 cm) width
E. Model/serial/rating plate location
A
B
D
C
E
A. Optional backguard may be installed.
B. 27
3
/
4
" (70.5 cm) depth with control panel (See NOTE.)
C. 35
3
/
4
" (90.8 cm) cooktop height when sitting on the
wheels
D. 36" (91.4 cm) width
E. Model/serial/rating plate location
7
48" (121.9 cm) models
NOTE: When installed in a 24" (61.0 cm) base cabinet with 25"
(63.5 cm) countertop; front of oven door protrudes 1
7
/
8
" (4.8 cm)
beyond 24" (61.0 cm) base cabinet.
Cabinet Requirements
Cabinet opening dimensions shown are for 25" (64.0 cm)
countertop depth, 24" (61.0 cm) base cabinet depth, and
36" (91.4 cm) countertop height. Dimensions must be met
in order to ensure a flush fit to back wall.
IMPORTANT: If installing a range hood or hood liner above
the range, follow the range hood or hood liner installation
instructions for dimensional clearances above the
cooktop surface.
* Receptacle must be rotated 90° for Canadian installation.
** Minimum Clearances
30" (76.2 cm) models: 30" (76.2 cm) minimum clearance
between the top of the cooking platform and the bottom of
an uncovered wood or metal cabinet
36" (91.4 cm) models: 42" (106.7 cm) minimum clearance
between the top of the cooking platform and the bottom of
an uncovered wood or metal cabinet
48" (121.9 cm) models: 42" (106.7 cm) minimum clearance
between the top of the cooking platform and the bottom of
an uncovered wood or metal cabinet
*** If the surface of the back wall is constructed of a combustible
material and a backguard is not installed, a 6" (15.2 cm)
minimum clearance is required for all models.
A
D
C
B
E
A. Optional backguard may be installed.
B. 27
3
/
4
" (70.5 cm) depth with control panel (See NOTE.)
C. 35
3
⁄
4
" (90.8 cm) cooktop height when sitting on the wheels
D. 48" (121.9 cm) width
E. Model/serial/rating plate location
M
K
N
G
I
F
D
E
B
C
**
A
H
I
L
J
Electrical
installation
area*
Gas
installation
area
J
F
O***
A. 18" (45.7 cm) upper cabinet to countertop
B. 30" (76.2 cm) model: 30" (76.2 cm) min. upper cabinet width
36" (91.4 cm) model: 36" (91.4 cm) min. upper cabinet width
48" (121.9 cm) model: 48" (121.9 cm) min. upper cabinet width
C. 13" (33 cm) max. upper cabinet depth
D. For minimum clearance to top of range**.
E. 30
1
/
4
" (76.8 cm) on 30" (76.2 cm) models
36
1
/
4
" (92.1 cm) on 36" (91.4 cm) models
48
1
/
4
" (122.6 cm) on 48" (121.9 cm) models
F. 6" (15.2 cm) min. clearance from both sides of range to side
wall or other combustible material
G. 15" (38.1 cm)
H. 22" (55.9 cm) on 30" (76.2 cm) models
28" (71.1 cm) on 36" (91.4 cm) models
40" (101.6 cm) on 48" (121.9 cm) models
I. 1
1
/
2
" (3.8 cm)
J. 3" (7.6 cm)
K. 5" (12.7 cm)
L. 6" (15.2 cm) on 30" (76.2 cm) models
14" (35.5 cm) on 36" (91.4 cm) models
24" (61.0 cm) on 48" (121.9 cm) models
M. 10
1
/
2
" (26.7 cm)
N. 6" (15.2 cm)
O. 6" (15.2 cm)***
8
Water Filtration System
LocationRequirements
(on some models)
For best results, do not install the water filtration system outside
or in extreme hot or cold temperatures. Temperature of water
supply to the water filtration system must be between 40°F (4°C)
and 100°F (38°C). Do not install on hot water supply line.
Locate the water filtration system near the cold water supply
pipe under the kitchen sink to filter cold water.
Make sure that the water filter assembly is installed in the
upright position.
It will be necessary to drill a 1/2" (13 mm) minimum diameter
hole in the upper-right or left rear corner of the side wall of
the cabinet under the sink to route the water supply tubing
through to the range.
Depending on your installation configuration, more routing holes
may be required.
Coil enough flexible codes-approved water supply tubing
behind the range to allow for the connection to the range to
be made behind the range prior to setting the range in place.
Typical Installation Configuration
NOTE: For unique installations, contact a licensed plumber.
In Massachusetts, a licensed plumber is required and the
Commonwealth of Massachusetts Plumbing Code 248-CMR
will be adhered to.
Water Supply Requirements
A cold water supply with water pressure between 30 and
120 psi (207 and 827 kPa) is required to operate the steam
feature. In Massachusetts, plumbing code 248 CMR 3.00 and
10.00 must be followed, and a licensed plumber will be used.
If you have questions about your water pressure, call a licensed,
qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of
a reverse osmosis system going to the water inlet valve of the
range needs to be between 30 and 120 psi (207 and 827 kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 psi (276 kPa).
If the water pressure to the reverse osmosis system is less than
40 psi (276 kPa):
■ Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter, if necessary.
■ Allow the storage tank on the reverse osmosis system to refill
after heavy usage.
If you have questions about your water pressure, call a licensed,
qualified plumber.
Cold water
supply
Hot
Cold
Filter
assembly
location
9
Electrical Requirements – U.S.A. Only
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrical installer determine
that the ground path and wire gauge are in accordance with
local codes.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that
the ground path is adequate.
Do not use an extension cord.
Be sure that the electrical connection and wire size are adequate
and in conformance with the National Electrical Code, ANSI/
NFPA 70 — latest edition — and all local codes and ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
WARNING: Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check with a
qualified electrician or service technician if you are in doubt as
to whether the appliance is properly grounded. Do not modify
the power supply cord plug. If it will not fit the outlet, have a
proper outlet installed by a qualified electrician.
Electrical Connection
To properly install your range, you must determine the type of
electrical connection you will be using and follow the instructions
provided for it here.
■ Range must be connected to the proper electrical voltage
and frequency as specified on the model/serial/rating plate.
The model/serial/rating plate is located under the console
on the right-hand side. Refer to the illustrations in “Product
Dimensions” in the “Location Requirements” section.
■ This range may be manufactured with a 4-wire power
supply cord or may not include a power supply cord. If your
range does not include a power supply cord, use a 4-wire
power supply cord rated at 250 volts, 40 or 50 amps, and
investigated for use with ranges.
Range Rating*
Specified Rating of Power
Supply Cord Kit and
Circuit Protection
120/240 Volts 120/208 Volts Amps Range Size
8.8–16.5 kW 7.8–12.5 kW 40 or 50** 30" (76.2 cm),
36" (91.4 cm)
16.6–22.5 kW 12.6–18.5 kW 50 48" (121.9 cm)
* The NEC calculated load is less than the total connected load
listed on the model/serial/rating plate.
** If connecting to a 50-amp circuit, use a 50-amp rated cord
with kit. For 50-amp rated cord kits, use kits that specify use
with a nominal 1
3
/
8
" (3.49 cm) diameter connection opening.
■ A circuit breaker is recommended.
■ Wire sizes and connections must conform with the rating
of the range.
■ The Tech Sheet is located behind the kick plate in a clear
plastic bag.
If connecting to a 4‑wire system:
This range is manufactured with the ground connected to the
cabinet. The ground must be revised, so the green ground wire
of the 4-wire power supply cord is connected to the cabinet.
See the “Electrical Connection – U.S.A. Only” section.
Grounding through the neutral conductor is prohibited for
new branch-circuit installations (1996 NEC), mobile homes,
recreational vehicles, or an area where local codes prohibit
grounding through the neutral conductor.
When a 4-wire receptacle of NEMA Type 14-50R is used, a
matching UL Listed, 4-wire, 250-volt, 40- or 50-amp, range
power supply cord must be used. This cord contains four copper
conductors with ring terminals or open-end spade terminals
with upturned ends, terminating in a NEMA Type 14-50R plug
on the supply end.
The fourth (grounding) conductor must be identified by a green
or green/yellow cover and the neutral conductor by a white
cover. Cord should be Type SRD or SRDT with a UL Listed strain
relief and be at least 4 ft (1.22 m) long.
The minimum conductor sized for the copper 4-wire power
cord are:
40-amp circuit
2 No.-8 conductors
1 No.-10 white neutral
1 No.-10 green grounding
If connecting to a 3‑wire system:
Local codes may permit the use of a UL Listed, 3-wire, 250-volt,
40- or 50-amp range power supply cord (pigtail). This cord
contains three copper conductors with ring terminals or open-
end spade terminals with upturned ends, terminating in a NEMA
Type 10-50P plug on the supply end. Connectors on the
appliance end must be provided at the point the power supply
cord enters the appliance. This uses a 3-wire receptacle of
NEMA Type 10-50R.
4-wire receptacle
3-wire receptacle (10-50R)
10
Electrical Requirements – CanadaOnly
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrical installer determine
that the ground path and wire gauge are in accordance with
local codes.
Be sure that the electrical connection and wire size are adequate
and in conformance with the CSA Standard C22.1, Canadian
Electrical Code, Part 1 — latest edition, and all local codes
and ordinances.
A copy of the above code standards can be obtained from:
Canadian Standards Association
178 Rexdale Blvd.
Toronto, ON M9W 1R3 CANADA
■ Check with a qualified electrical installer if you are not sure
the range is properly grounded.
■ When a 4-wire, single-phase 250-volt, 60 Hz., AC-only
electrical supply is available, a 40-amp minimum circuit
protection is required on 30" (76.2 cm) and 36" (91.4 cm)
ranges and a 50-amp minimum circuit protection is required
on 48" (121.9 cm) ranges, fused on both sides of the line.
■ A time-delay fuse or circuit breaker is recommended.
■ This range is equipped with a CSA International Certified
Power Cord intended to be plugged into a standard 14-50R
wall receptacle. Be sure the wall receptacle is within reach of
range’s final location.
■ Do not use an extension cord.
Gas Supply Requirements
Observe all governing codes and ordinances.
IMPORTANT: This installation must conform with all local codes
and ordinances. In the absence of local codes, installation
must conform with American National Standard, National Fuel
Gas Code ANSI Z223.1 — latest edition — or CAN/CGA B149
— latest edition.
IMPORTANT: Range must be connected to a regulated
gas supply.
IMPORTANT: Leak testing of the range must be conducted
according to the manufacturer’s instructions.
Type of Gas
Natural Gas:
The model/serial rating plate located on the right vertical surface
of the oven door frame has information on the types of gas that
can be used. If the types of gas listed do not include the type of
gas available, check with the local gas supplier.
Propane Gas conversion:
Conversion must be done by a qualified service technician.
No attempt shall be made to convert the range cooktop from
the gas specified on the model/serial/rating plate for use with
a different gas without consulting the serving gas supplier.
To convert to Propane gas, use the Propane gas conversion
kit provided with your range and see the “Gas Conversions”
section. The parts for this kit are in the package containing
literature supplied with the range.
WARNING
Electrical Shock Hazard
Electrically ground range.
Failure to do so can result in death, fire, or
electrical shock.
WARNING
Explosion Hazard
Use a new CSA International approved gas supply line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to propane, have a qualified person make
sure gas pressure does not exceed 14" (36 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
11
Gas Supply Line
■ Provide a gas supply line of 3/4" (19 mm) rigid pipe to the
cooktop location. A smaller size pipe on longer runs may
result in insufficient gas supply. With Propane gas, piping
or tubing size can be 1/2" (13 mm) minimum. Usually,
Propane gas suppliers determine the size and materials
used in the system.
NOTE: Pipe-joint compounds that resist the action of
Propane gas must be used. Do not use TEFLON
®†
tape.
Flexible metal appliance connector:
■ If local codes permit, a new CSA design-certified, 4-5 ft
(122-152 cm) long, 5/8" (16 mm) or 3/4" (19 mm) I.D.,
flexible metal appliance connector may be used for
connecting the cooktop to the gas supply line.
■ A 1/2" (13 mm) male pipe thread is needed for
connection to the female pipe threads of the inlet to the
appliance pressure regulator.
■ Do not kink or damage the flexible metal tubing when
moving the cooktop.
IMPORTANT: All connections must be wrench-tightened.
Do not make connections to the gas regulator too tight.
Making the connections too tight may crack the regulator
and cause a gas leak. Do not allow the regulator to turn or
move when tightening fittings.
■ Must include a shut-off valve:
Install a manual gas line shut-off valve in an easily accessible
location. Do not block access to shut-off valve. The valve is
for turning on or shutting off gas to the cooktop.
Gas Pressure Regulator
The gas pressure regulator supplied with this cooktop must
be used. The inlet pressure to the regulator should be as
follows for proper operation:
Natural Gas:
Minimum pressure: 15.2 cm WCP
Maximum pressure: 35.6 cm WCP
Propane Gas:
Minimum pressure: 27.9 cm WCP
Maximum pressure: 35.6 cm WCP
Contact local gas supplier if you are not sure about the
inlet pressure.
Burner Input Rating — Altitude
Input ratings shown on the model/serial/rating plate are for
elevations up to 2,000 ft (609.6 m).
For elevations above 2,000 ft (609.6 m), ratings need to be
reduced at a rate of 4% for each 1,000 ft (304.8 m) above
sea level (not applicable for Canada).
Gas Supply Pressure Testing
Gas supply pressure for testing regulator must be at least 2.5 cm
water column pressure above the manifold pressure shown on
the model/serial/rating plate.
Line pressure testing above 1/2 psi (3.5 kPa) gauge
(35.6 cm WCP)
The cooktop and its individual shut-off valve must be
disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess of
1/2 psi (3.5 kPa).
Line pressure testing at 1/2 psi (3.5 kPa) gauge
(35.6 cm WCP) or lower
The cooktop must be isolated from the gas supply piping
system by closing its individual manual shut-off valve during
any pressure testing of the gas supply piping system at test
pressures equal to or less than 1/2 psi (3.5 kPa).
A
B
C
A. Gas supply line
B. Shut-off valve open position
C. To cooktop
†
®
TEFLON is a registered trademark of Chemours.
12
INSTALLATION INSTRUCTIONS
Unpack the Range
1. Remove shipping materials, tape, and film from range.
Keep shipping pallet under range. Remove oven racks,
grates, and parts package from inside oven.
2. Remove kick plate.
Your range will either have the kick plate already installed
(follow Option 1) or packaged on top of the unit (follow
Option 2).
Option 1
a. Remove foam between door and kick plate.
b. Remove screws from kick plate.
c. Lift up on kick plate to release plate from shoulder
screws.
d. Lay kick plate to the side to avoid scratching the
stainless steel.
Option 2
a. Remove kick plate from top of range and grate pack.
b. Lay kick plate to the side to avoid scratching the
stainless steel.
c. Remove screws from range.
3. For 48" (121.9 cm) models only, rotate center support
counterclockwise off the pallet until it stops.
NOTE: This support is used only for shipping and is not
needed for installation.
4. Lay a piece of cardboard from side packaging on the floor
behind range. Using two or more people, firmly grasp
each side of range. Lift range up about 3" (8.0 cm) and
move it back until range is off shipping pallet. Set range
on cardboard to avoid damaging floor.
WARNING
Excessive Weight Hazard
Use two or more people to move and install range.
Failure to do so can result in back or other injury.
A
B
A. Kick plate
B. Remove these screws.
In packaging
A. Kick plate
A
Packaging removed
A. Kick plate
A
A. Remove these screws.
13
Install Optional Backguard
All ranges may require a backguard. See “Cabinet Dimensions”
in the “Location Requirements” section. See the “Tools and
Parts” section for information on ordering.
Remove island trim and attach backguard using six screws.
Insert three from the front and three from the back (9" [22.9 cm]
backguard shown).
Install Anti-Tip Bracket
1. Determine which mounting method to use: floor or wall.
If you have a stone or masonry floor, you can use the
wall mounting method.
2. Determine and mark centerline of the cutout space. The
mounting bracket must be installed on the right side of the
cutout. Position mounting bracket in cutout as shown in the
following illustration.
Measurement B:
30" (76.2 cm) ranges: 14
1
⁄
4
" (36.1 cm)
36" (91.4 cm) ranges: 17
1
⁄
4
" (43.8 cm)
48" (121.9 cm) ranges: 23
3
⁄
8
" (59.3 cm)
Measurement C:
Optional distance from back wall. If back wall is constructed
of a combustible material and a backguard is not installed, a
6" (15.2 cm) minimum clearance is required for all models.
Install anti-tip bracket accordingly.
3. Drill two 1/8" (3.0 mm) holes that correspond to the bracket
holes of the determined mounting method. See the following
illustrations.
Floor Mounting
Wall Mounting
4. Using a Phillips screwdriver, mount anti-tip bracket
to the wall or floor with the two #12 x 1
5
⁄
8
" (4.1 cm)
screws provided.
Depending on the thickness of your flooring, longer screws
may be necessary to anchor the bracket to the subfloor.
Longer screws are available from your local hardware store.
5. Move range close enough to opening to allow for electrical
connections to be made. Remove shipping base, cardboard,
or hardboard from under range.
6. Continue installing your range using the following
installation instructions.
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation
instructions.
Slide range back so rear range foot is engaged in the
slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed
and engaged.
Failure to follow these instructions can result in death
or serious burns to children and adults.
A
B
C
A. Centerline
B. Centerline of cutout to outside
edge of anti-tip bracket
C. Back wall to back of range
B
A
A. #12 x 1
5
⁄
8
" (4.1 cm) screws
B. Anti-tip bracket
B
A
A. #12 x 1
5
⁄
8
" (4.1 cm) screws
B. Anti-tip bracket
14
Electrical Connection – U.S.A. Only
30" (76.2 cm) and 36" (91.4 cm) Models 48" (121.9 cm) Models
1. Disconnect power.
2. Remove the terminal block cover screws and disengage
mounting tabs to remove terminal block cover from back
of range.
3. Add power supply cord strain relief.
■ Assemble a UL Listed strain relief in the opening.
■ Tighten strain-relief screw against the power supply cord.
4. Complete installation following instructions for your type
of electrical connection:
4‑wire (recommended)
3‑wire (if 4-wire is not available)
Electrical Connection Options
If your home has:
And you will be
connecting to:
Go to
section:
4-wire receptacle
(NEMA type 14-50R)
A UL Listed,
250-volt minimum,
40- or 50-amp,
range power supply
cord
4-Wire
Connection:
Power Supply
Cord
3-wire receptacle
(NEMA type 10-50R)
A UL Listed,
250-volt minimum,
40- or 50-amp,
range power supply
cord
3-Wire
Connection:
Power Supply
Cord
A
B
C
A. Phillips head screws
B. Terminal block cover
C. Two mounting tabs at bottom
A
A. UL Listed strain relief
15
4‑Wire Connection: Power Supply Cord
Use this method for:
■ New branch-circuit installations (1996 NEC)
■ Mobile homes
■ Recreational vehicles
■ In an area where local codes prohibit grounding through
the neutral
1. Remove the ground-link screw from the range frame. Save
the ground-link screw. Bend the ground link away from the
range so that it does not contact the range.
2. Connect the green ground wire from the power supply
cord to the range using the ground-link screw. The ground
wire must be attached first and must not contact any other
terminal.
3. Use a 1/4" (64 mm) nut driver to remove the hex washer
head screws from the terminal blocks.
4. Connect the neutral (center) wire to the center terminal
connector using one of the hex washer head screws.
Securely tighten screw for proper electrical connection.
5. Connect the other two wires (lines 1 and 2) to the outer
aluminum terminal blocks.
6. Securely tighten screws for proper electrical connection.
7. Tighten strain-relief screws.
8. Replace terminal block cover.
3‑Wire Connection: Power Supply Cord
Use this method only if local codes permit connecting cabinet-
ground conductor to neutral wire of power supply cord.
1. Use a 1/4" (64 mm) nut driver and remove the hex washer
head screws from the aluminum terminal blocks.
2. Connect the neutral (center) wire to the center terminal
connector using one of the hex washer head screws.
Securely tighten screw for proper electrical connection.
3. Connect the other two wires (lines 1 and 2) to the outer
terminal screws on the terminal block.
4. Tighten strain-relief screws.
5. Replace terminal block cover.
Install Water Filtration System
(on some models)
Install Model W10049700 Water Filter
1. Install the water filter near the cold water supply pipe under
the kitchen sink to filter the cold water.
IMPORTANT: Be sure to allow a minimum clearance of
1
1
/
2
" (3.8 cm) under the filter system for removing the
filter cartridge.
Make sure that the water filter assembly is installed
in the upright position.
Typical Installation Configuration
NOTE: For unique installations, contact a licensed plumber.
In Massachusetts, a licensed plumber is required and the
Commonwealth of Massachusetts Plumbing Code 248-CMR
will be adhered to.
A
B
A. Ground-link screw
B. Ground link bent away from range
A
B
C
D
E
F
G
H
I
A. Line 1
B. Green ground wire
C. Ground-link screw
D. Hex washer head screw
E. Silver-colored terminal
block screw
F. Ground link
G. Neutral (center) wire
H. Line 2
I. UL Listed strain relief
and 40- or 50-amp
range power supply cord
A
B
C
D
E
F
G
A. Line 1
B. Ground link
C. Hex washer head screw
D. Silver-colored terminal
block screw
E. Neutral (center) wire
F. Line 2
G. UL Listed strain relief
and 40- or 50-amp
range power supply cord
Filter
Assembly
Cold water
supply
Hot
Cold
Water supply
line to cold
water supply
Water supply
line to oven
16
2. Attach the supplied water filter mounting ring and screw
at the recommended location.
3. Attach filter to the mounting ring.
Connect to Home Water Supply
1. Make connection to the cold water supply line.
■ A leak-tight connection to the 1/4" (6.4 mm) flexible
codes-approved water supply line must be provided.
■ Check local codes for type of connection required.
■ Flexible codes-approved water supply line must be
cut with a tubing cutter so the ends are concentric
and without burrs.
NOTE: It is recommended that the cold water line be soft water.
Connect to Water Filter Inlet (yellow)
NOTE: Use the quick-connect stem and/or elbow adapter
fittings in the combination needed for your installation
configuration.
1. Attach the supplied 3/8" (9.5 mm) to 1/4" (6.4 mm) stem
or 3/8" (9.5 mm) to 1/4" (6.4 mm) elbow quick-connect
adapter fitting to the yellow water filter inlet connection
by pushing the quick-connect fitting past the O-ring until
you hit the backstop.
2. Connect the flexible codes-approved water supply line
(not provided) from the home cold water supply pipe to
the quick-connect adapter fitting you just installed on
the filter inlet (yellow) side of the water filter.
3. Pull tube to ensure it is secured.
If you need to release tubing:
Push in collet to release tubing. With collet held in, pull tubing
straight out.
Connect to Water Filter Outlet (blue)
1. Attach the supplied 3/8" (9.5 mm) to 1/4" (6.4 mm) stem
or 3/8" (9.5 mm) to 1/4" (6.4 mm) elbow quick-connect
adapter fitting to the blue water filter outlet connection by
pushing the quick-connect fitting past the O-ring until you
hit the backstop.
2. Connect another piece of flexible codes-approved water
supply line to the quick-connect adapter fitting you just
installed on the filter outlet (blue) side of the water filter.
3. Pull tube to ensure it is secured.
4. Route flexible codes-approved water supply line
through under-sink cabinet and oven cabinet cutout.
Mounting ring and scre
w
1½" (3.8 cm) clearance
A
B
A. Quick-connect elbow adapter fitting
B. Quick-connect stem adapter fitting
C
B
A
A. 1/4" (6.4 mm) water supply tubing
B. O-ring
C. Backstop
A
A. Collet
W
ater
suppl
y
connection
Shutoff
valve
Water supply tubing
to cold water supply
Yellow
WATER
IN
Water supply tubing to range
Blue
WATE
R
OUT
Filter
Sink
17
5. Connect the flexible codes-approved water supply line
to the range copper tubing, using a 1/4" (6.4 mm) to
1/4" (6.4 mm) water supply union.
6. Turn on water supply.
7. Check all connections for leaks.
NOTE: No flushing or conditioning of the water filter is required
prior to use.
Make Gas Connection
1. Assemble flexible connector from gas supply pipe to
pressure regulator located in the middle rear of the range.
2. Apply pipe-joint compound made for use with Propane gas
to the smaller thread ends of the flexible connector adapters.
(See B and G in the following illustration.)
3. Attach one adapter to the gas pressure regulator and
the other adapter to the gas shut-off valve. Tighten both
adapters, being certain not to move or turn the gas pressure
regulator.
4. Use a 15/16" (24 mm) combination wrench and an adjustable
wrench to attach the flexible gas supply to the adapters.
Check that connector is not kinked.
IMPORTANT: All connections must be wrench-tightened.
Do not make connections to the gas regulator too tight. Making
the connections too tight may crack the regulator and cause a
gas leak. Do not allow the regulator to turn or move when
tightening fittings.
Complete Connection
1. Open the manual shut-off valve in the gas supply line. The
valve is open when the handle is parallel to the gas pipe.
2. Test all connections by brushing on an approved
noncorrosive leak-detection solution. If bubbles appear,
a leak is indicated. Correct any leak found.
3. Remove cooktop burner caps, burner bases, and grates
from parts package. Place burner bases on cooktop. Place
burner caps on burner bases. Place grates over burners
and caps.
4. Check that the range is plugged into the appropriate
grounded outlet. (See the “Electrical Requirements” section.)
5. Turn on power supply. For further information, please refer
to the user instructions located in the Use and Care Guide.
Verify Anti-Tip Bracket Location
1. Using a 5/16" (7.9 mm) socket or wrench, turn all four
leveling rods one full turn to raise the range and provide
enough clearance for the rear leveling leg to slide into the
anti-tip bracket.
2. Move range into its final location, making sure rear leveling
leg slides into anti-tip bracket.
3. Use a flashlight to look underneath the bottom of the range
and visually check that the rear range foot is inserted into
the slot of the anti-tip bracket.
B
C
D
A
E
F
A. To home water supply
B. Rear of cabinet cutout
C. Flexible codes-approved water supply
line from home water supply
D. 1/4" (6.4 mm) to 1/4" (6.4 mm) water
supply union (supplied in water filter kit)
E. Oven copper tubing
F. Range front
WARNING
Explosion Hazard
Use a new CSA International approved gas supply line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to propane, have a qualified person make
sure gas pressure does not exceed 14" (36 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
A
B
C
D
E
FG
H
A. Gas pressure regulator
B. Use pipe-joint compound.
C. Adapter (must have 1/2"
[13 mm] male pipe thread)
D. Flexible connector
E. Manual gas shut-off valve
F. 1/2" (13 mm) or
3/4" (19 mm) gas pipe
G. Use pipe-joint compound.
H. Adapter
A
B
A. Closed valve
B. Open valve
18
Level Range
NOTE: Range must be level for satisfactory baking performance.
1. Place rack in oven.
2. Place level on rack and check levelness of the range, first
side to side, then front to back.
3. If range is not level, adjust the leveling rods. Turn leveling
rods located behind the kick plate to level range and to raise
or lower range to the desired countertop height.
NOTE: All roller feet must be off the floor upon final installation.
Install Grill Grease Trays
(on grill models)
1. Remove flame spreader. Pull forward slightly on the flame
spreader to release the tabs from the rear slots and lift out.
2. Cut and remove tie strap from rear of burner assembly.
3. Lift burner assembly up and out to remove.
4. Slide drip tray into opening on the right front side of the grill
basin. There are guides to assure correct placement of the
drip tray.
5. Insert the large grease tray all the way under the back edge
of the grill basin and hook it into the slots.
6. Insert the small grease tray all the way under the front of the
grill basin and hook it into the slots.
When the two grease trays are installed properly, the small
grease tray will hook over the large grease tray.
A
A
B
B
A. Rear leveling rod
B. Front and brass leveling rod
A
B
A. Grill front
B. Rear tabs and slots
A
A. Tie strap
A
A. Drip tray
A
B
A. Large grease tray
B. Slots
A
B
C
D
A. Large grease tray
B. Grease tray connection
C. Small grease tray
D. Slots
19
7. Insert the orifice tube on the front of the burner assembly
into the opening at the front of the grill basin and set burner
assembly into place.
8. Insert front tabs of the flame spreader into slots at the front
of the grill basin, then the rear tabs into the rear slots.
9. Check the surface burner and grill flames. Refer to the
“Electronic Ignition System” section.
10. Place the wave tray on top of the flame spreader.
11. Place the grill grate into position.
Install Griddle
(on griddle models)
The griddle is factory installed.
1. Place drip tray in the well at the front of the griddle. Slide tray
toward the back until it stops.
2. Clean griddle before using. Refer to the Use and Care Guide.
Electronic Ignition System
Install Burner Bases and Burner Caps
Install the burner base, making sure the igniter electrode is
properly aligned with the base. Place burner caps on top
of burner bases. If burner caps are not properly positioned,
surface burners will not light.
Ultra Power™ Dual‑Flame Burner
Professional Burner
Simmer/Melt Burner
Initial Lighting and Gas Flame Adjustments
Cooktop burners use electronic igniters in place of standing
pilots. When the cooktop control knob is turned to any position,
the system creates a spark to light the burner. This sparking
continues until the flame is lit or the knob is turned to OFF.
NOTE: The first time igniting the burners will take longer. This
allows the gas to reach the burners during the first use.
Check Operation of Cooktop Burners
Push in and turn each control knob to LITE.
NOTE: You will hear a clicking sound while the line clears.
The surface burners and grill flames should light within
4 seconds. The first time a burner is lit, it may take longer
than 4 seconds to light because of air in the gas line.
After verifying the proper burner operation, turn the control
knobs to OFF.
If burners do not light properly:
■ Turn cooktop control knob to OFF.
■ Check that the cooktop is plugged in and the circuit breaker
has not tripped or the fuse has not blown.
■ Check that the gas shut-off valves are set to the
open position.
■ Check that burner caps are properly positioned on
burner bases.
Repeat start-up. If a burner does not light at this point, contact
your dealer or authorized service company for assistance.
A
A. Front opening
A
B
A. Front tabs and slots
B. Rear tabs and slots
A
B
A. Griddle drip tray
B. Griddle
A
B
A. Incorrect
B. Correct
A
B
A. Incorrect
B. Correct
A
B
A. Incorrect
B. Correct
20
Flame Height
The cooktop flame should be a steady blue flame approximately
1/4" (6.4 mm) high.
Dual Flame Burner
Single Flame Burner
To Adjust Flame Height:
1. Unplug range or disconnect power.
2. Remove burner grates.
3. Remove the control knobs.
4. Open the oven door and remove the two screws on each
side of the range that hold the control console in place.
NOTE: Make sure to leave oven door open or the control
console will not rest in the side brackets properly once it
is detached.
5. Pull up on the control console and let it drop forward into
the notched console brackets on each side.
6. Remove the round gasket from the valve stem.
7. Put a control knob onto the valve stem of the burner
you want to adjust.
8. Turn the control knob to LO and, using a butane extension
lighter, light the burner.
9. Remove the control knob.
10. Use a 1/8" x 4
1
/
4
" (3.2 mm x 108 mm) flat-blade screwdriver
to adjust the flame height. Tighten screw to reduce flame
height. Loosen screw to increase flame height.
NOTE: When you are converting to Propane gas, the screw
should be tightened down completely on the single-output
valves. The dual-output valve should not be adjusted.
11. When finished adjusting the flame height, put a control knob
back onto the valve stem and turn off the burner.
12. Remove the control knob.
13. Replace the round gasket.
14. Repeat steps 6 through 13 for any other burners that
need adjustment.
15. Lift up on the control console and set it back into place.
For a proper fit, the flange of the control console must hook
over the lip on the front of the range cooktop.
A
B
A. Upper (simmer) flame
B. Lower flame
A
A. Control console bracket
A
B
A. Single flame burner adjustment screw (on right side of valve)
B. Dual flame burner adjustment screw (on left side of valve)
A
B
A. Control console flange
B. Front lip of range cooktop
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
KitchenAid KDRS407VBU01 Guide d'installation
- Catégorie
- Cuisinières
- Taper
- Guide d'installation
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
KitchenAid KDRS467VSS Guide d'installation
-
KitchenAid KDRS467VSS Mode d'emploi
-
-
KitchenAid KDRU763VSS Guide d'installation
-
-
-
KitchenAid KDRS407VSS00 Guide d'installation
-
KitchenAid KGCU407VSS Guide d'installation
-
-