jbc AM 6000 Manuel utilisateur

Index Page

English 1

Español 25

Français 49

Deutsch 73

Italiano 97

0780448-0

GARANTIE DEUTSCH

Für das vorliegende Gerät übernimmt

JBC eine Garantie von 2 Jahre, für alle

Fabrikationsfehler. Diese Garantie

schliesst die Reparatur bzw. den Ersatz

der defekten Teile sowie die

entsprechenden Arbeitskosten ein.

Ausgeschlossen von dieser

Garantieleistung sind durch

unsachgemässen Gebrauch

hervorgerufene Betriebsstörungen und

normale Gebrauchsabnützungen.

Zur Inanspruchnahme dieser Garantie

muss das Gerät portofrei an den

Vertriebshändler geschickt werden, bei

dem es gekauft wurde. Fügen Sie dieses

vollständig, ausgefüllte Blatt, bei.

GARANZIA ITALIANO

La JBC garantisce quest'apparato 2

anni contro ogni difetto di fabbricazione,

e copre la riparazione e la sostituzione

dei pezzi difettosi, includendo la mano

d'opera necessaria.

Sono escluse da questa garanzia le

avarie provocate da cattivo uso

dell'apparato e logorio da utilizzo.

Per usufruire di questa garanzia, è

indispensabile inviare, in porto franco,

l'apparato al distributore presso il quale

è stato acquistato, unitamente a

questo foglio debitamente compilato.

DATE OF PURCHASE

FECHA DE COMPRA

DATE D'ACHAT

KAUFDATUM

DATA DI ACQUISTO

STAMP OF DEALER

SELLO DEL DISTRIBUIDOR

CACHET DU DISTRIBUTEUR

STEMPEL DES HÄNDLERS

TIMBRO DEL DISTRIBUTORE

SERIAL Nº

✂

AM 6000

REWORK STATION

MANUFACTURED BY

JBC Industrias, S.A.

Ramón y Cajal, 3 - 08750 MOLINS DE REI

BARCELONA - SPAIN

Tel.: +34 93 325 32 00 - Fax: +34 93 680 49 70

http://www.jbctools.com e-mail:[email protected]

Instructions manual

CE Version

ENGLISH

1

We appreciate the confidence you have placed in JBC in purchasing this station.

It is manufactured to the most stringent quality standards in order to give you the

best possible service. Before turning on your station, we recommend you to read

these instructions carefully.

Extractor stand

Ref.0932845

Tripod 20

Ref.0932050

Tripod 40

Ref.0932250

Soldering iron stand

AD 8200

Ref.0268200

Desoldering iron

DR 5600

Ref.5600000

* Handpiece 2210

Ref.2210000

Cartridges 2245

Pick & Place

MP 2260

Ref.2260000

AM 6000

rework station

Pick & Place and extractors

vacuum selection

Heater stand JT 8700

Ref.0828700

Equipotential

terminal

* These elements are not

supplied with the station

Spare filters

Ref.0781046

* Hot tweezers stand

PA 8120

Ref.0748120

* Hot tweezers stand

PA 8110

Ref.0748110

Handpiece 2245

Ref.2245000

* Hot tweezers

PA 4200

Ref.4200000

* Cartridges for the hot tweezers PA 4200

* Micro hot tweezers

PA 1200

Ref.1200000

* Cartridges 1200

Desoldering iron stand

DR 8500

Ref.0788500

External desoldering air filter

Ref.0821830

2

ENGLISH

SPECIFICATIONS

The AM 6000 is a rework station for through-hole and

SMT boards.

- AM 6000 230V Ref. 6000200

It contains 4 modules which cover the main rework

tasks:

- Hot air for desoldering any size of SMD

components.

The station uses the exclusive JBC system,

based on protectors-extractors and hot-air flow,

which makes desoldering clean and quick,

concentrating the heat on the IC, and protecting

the rest of the circuit at the same time.

A medium-sized SMD can be desoldered in less

than 20 seconds.

- Desoldering SMTs and cleaning of through-hole

components and pads by using the desoldering

iron DR 5600, which contains a self-contained

vacuum pump.

- Pick & Place MP 2260 pencil by suction to aid

components positioning.

- Soldering of all types of components, with the

swift response, power and temperature recovery

of the Advanced series. You can connect the

Advanced 2010, 2210, 2045 or 2245 handpieces

and the hot tweezers PA 1200 or PA 4200.

The station’s components

- Control Unit with 900 W heater

- Handpiece 2245 Ref. 2245000

with the cartridge 2245-003 Ref. 2245003

- Desoldering iron DR 5600 Ref. 5600000

with the tip 5600-003 Ref. 5600003

- Pick & Place MP 2260 Ref. 2260000

Accessories for the heater:

- Heater stand JT 8700 Ref. 0828700

- Extractor stand Ref. 0932845

- Set of 5 protectors (Fig. 1, page 128)

- Set of 5 extractors (Fig. 2, page 128)

-2 tripods for the protectors (Fig. 1, page 128)

- Set of 4 suction cups Ref. 0930110

-3 nozzles

In order to make the nozzles removal easier, the

stand has a special bushing.(Fig. 3, page 128).

- Suction tube with connectors Ref. 0932330

- Pedal with cable and connector Ref. 0964551

Accessories for the handpiece:

- Soldering iron stand AD 8200 Ref. 0268200

Accessories for the desoldering iron:

- Desoldering iron stand DR 8500 Ref. 0788500

- External desoldering air filter Ref. 0821830

- Spare filters Ref. 0781046

- Set of accessories Ref. 0780593

Accessories for the Pick & Place:

- Set of suction cups Pick & Place Ref. 0940163

- Set of straight needles Ref. 0901546

- Set of bent needles Ref. 0861660

- Instruction manual Ref. 0780448

The AM 6000 station has the following

complementary products:

- Handpiece 2010 Ref. 2010000

- Handpiece 2210 Ref. 2210000

- Handpiece 2045 Ref. 2045000

- Micro hot tweezers PA 1200 Ref. 1200000

- Hot tweezers PA 4200 Ref. 4200000

ENGLISH

3

OPERATION

Description of controls

- PEDAL:

Hot air is produced when it is held down.

Releasing it the heater is disconnected,

though the turbine continues to operate until

the air temperature falls below 100°C.

- BUTTONS:

Activates or desactivates the hot-air flow. After a

function-time of two minutes the hot-air flow

switches automatically off.

The red light indicates, that the heating element

is functioning. A malfunction is indicated by the

pulsing of the red led.

On/off switch for the self-contained suction pump.

The yellow light of the switch indicates that the

self-contained vacuum pump is activated.

- CONTROLS:

TEMPERATURE

Allows fixing the temperature of the heater

between 150 and 455°C. The selected

temperatures are reference values which may

change depending on the distance between

the heating element and the nozzle.

Allows fixing the temperature of the soldering

and desoldering iron between 100 and 371°C.

AIR FLOW

This enables the air flow to be set on a scale

from 1 (corresponding to the lowest setting

of 6 l/min) to 10 (corresponding to the highest

of 45 l/min).

- VACUUM SELECTOR:

Two vacuum inlets avalaible, being active

the one that coincides with the arrow.

HEAT

VACUUM

Control Unit technical specifications

- Maximum power soldering iron 50W

- Maximum power desoldering iron 75W

- Power heating unit 900W

- Temperature selection of the soldering part :

100 to 371°C (±5%)

- Temperature selection of the desoldering part:

100 to 371°C (±5%)

- Temperature selection hot air:

150 to 455°C (±5%)

- Air flow regulation: 6-45 l/min

- Self-contained vacuum pump for holding ICs

- Station's maximum power: 1150W

- ESD protected housing.

Typical surface resistance: 10

5

-10

11

Ohms/square

- Complies with CE standards on electrical safety,

electromagnetic compatibility and antistatic

protection.

- Equipotential connector is earth connected to the

plug feed of the station.

- Weight of complete unit: 17.6 kg

- In the SOLD. connector you can only connect

handpieces 2010, 2210, 2045 and 2245 and the

hot tweezers PA 1200 and PA 4200.

- In the DESOLD. connector you can only connect

the desoldering iron DR 5600.

Safety measures

- Incorrect use of this tool may cause fire.

- Be cautious when using the tool in places

where inflamable products are stored.

- Heat can fire up inflamable products even

when they are not at sight.

- Do not use when the atmosphere is explosive.

- Place the tool back on its stand in order to let

it cool down before you store it.

4

ENGLISH

- Use the pedal or the HEAT button to start the

self-contained hot-air pump, directing it with a

circular movement at the component terminals

and taking care to distribute the heat evenly.

- When the soldering flux turns liquid the extractor

will automatically lift the component.

B) Extractor:

- Select extractor size in function of the IC to be

desoldered. Use the VACUUM button to start

the pump.

DESOLDERING PROCEDURE WITH THE

HEATER

We would also recommend the use of the nozzles of

larger diameter, reserving the smallest one (diam. 4

mm) for desoldering small components such as

resistors, condensers and the like, bearing in mind

that with this small nozzle the concentration of heat

is greater and care must be taken to avoid burning

the printed circuit; we recommend keeping below a

temperature of 350 °C and air flow of 6.

Depending on the size of the integrated circuit to be

desoldered, you will have to use:

A)Protector + tripod.

B)Extractor.

C) Tripod.

A) Protector + tripod:

- Select protector and tripod size in function of

the IC to be desoldered and place it over the

component.

- Use the VACUUM button to start the pump and

then fit the tripod. Press the sucker down until it

sticks onto the component.

ENGLISH

5

There are different models of protectors and

extractors as accessories.

The measurements of all the extractors and

protectors are given on page 128 of instructions

manual.

C) Tripod:

For small components for which an extractor

cannot be used, we recommend use of tripod 20

Ref. 0932050, as shown in the figure.

Use the tripod 40 Ref. 0932250 for larger integrated

circuits.

SOLDERING PROCEDURE

1 After desoldering the component, any solder

left on the printed circuit should be removed

with our desoldering iron DR 5600 ref. 5600000.

- Fit the extractor and press the sucker down until

it sticks onto the component.

- Use the pedal or the HEAT button to start the

self-contained hot-air pump, directing it with a

circular movement at the component terminals

and taking care to distribute the heat evenly.

- When the soldering flux turns liquid the extractor

will automatically lift the component.

6

ENGLISH

Soldering Iron 2210 ref. 2210000 for great

precision tasks, like SMD solders, etc.

Soldering Iron 2245 ref. 2245000 for general

soldering tasks in professional electronics.

These soldering irons have a wide range of

cartridges with different models of tips. The

cartridge 2245-009 and 2245-010 are specially

designed for soldering SMD circuits of the

QFP and PLCC types.

Solder wire with a diameter of between 0.5 and

0.7 mm should be used.

6 Depending on the nature of the component to be

soldered, use soldering paste together with our

hot air station TE 5000, which gives very

accurate air-flow regulation, between 4 and 11

l/min.

2 Place the component or printed circuit with

the Pick & Place MP 2260 ref. 2260000.

3 When the component is correctly placed, solder

its pins.In the case of integrated circuits of the

Flat Pack type, first solder one pin of every IC

angle to fix it in place in the circuits.

4 Apply Flux FL 9582 ref. 0046565 in pads and

leads.

5 Solder the remaining pins. For this we

recommend to use our soldering irons of the

Advanced series, which are available in two

different models:

ENGLISH

7

MAINTENANCE

Exchanging the heater.

Use a wrench to unscrew the cover.

Exchanging the resistor from the heater.

1. Move back the spring. Untighten the screws.

Follow this process inverted to re-connect the heater.

Move back the spring and the cover. Pull the

connector from the socket to disconnect the heater

from the station.

2. To take out the resistor, press down the lower

part of the heater on a fixed surface.

4. Connect the new resistor, pushing it’s extreme.

5. Fix the screws tightly to avoid air-loss which

could reduce the resistor’s lifetime. Finally put

the spring back in it’s place.

3. Separate the resistor from the heater’s cable.

O-ring ø17 x ø1,8

8

ENGLISH

OPERATING INCIDENTS

The suction cup does not adhere to the

component.

Deficient aspiration, Vacuum.

1 Verify if the suction cup is well placed and in

perfect condition.

Possible errors

In the case of malfunction, the control unit

interrupts the connection.

Following a list of the most common

malfunctions:

- Power failure.

Check for blown fuses.

- The temperature will not rise.

Possible causes:

· Heating element open.

· In case of a long low-power period.

- No reading from the thermocouple.

Possible cause: open thermocouple.

- Insufficient air flow which causes an excesive

rise of the heating temperature.

Before recuperating this type of error you must

wait until the temperature goes down.

Possible causes: leaking or blocked air conducts

or faulty self-contained air pump.

Filter

Ref. 0861800

2 Check the incoming air filter in the interior of

the station and replace it if dirty or obstructed.

- Faulty reading of the rotationsmeter of the self-

contained air pump.

Possible causes: air pump damaged or faulty

function of the optical sensor circuit.

To recuperate any of these errors actuate the

general switch at the back of the station, the

pedal should not be pushed at this moment.

ENGLISH

9

DESOLDERING IRON DR 5600

The AM 6000 station includes the following:

- Desoldering iron DR 5600 ref. 5600000 with the

tip 5600-003 ref.5600003.

Power desoldering iron: 75W.

- Desoldering iron stand DR 8500 ref. 0788500.

- External desoldering air filter ref. 0821830.

- Set of accessories ref. 0780593 with tips for the

desoldering iron: 5600-003, 5600-004 and 5600-

005.

The desoldering iron is connected to the station

following the below procedure:

The cable connection of the desoldering iron is

connected to the plug in the desoldering iron stand

DR 8500 and the vacuum hose is connected to the

external desoldering air filter, which is connected to

the vacuum connection SUCTION of the station. The

cable connection of the desoldering iron stand is

plugged into the terminal DESOLD of the station.

Very important, it is essential to connect the mentioned

filter to prevent from damaging the vacuum pump.

Desoldering iron stand

DR 8500

Ref.0788500

Desoldering iron

DR 5600

Ref.5600000

Spare filters

Ref.0781046

Heating element

Ref.5600010

Vacuum inlet

SUCTION

Desoldering

connector

DESOLD

External desoldering air filter

Ref.0821830

10

ENGLISH

OPERATION

LED lights

Red LED -ON- when lit, it indicates that the station is

plugged in the mains.

Green LED -READY- when lit, it indicates that the

system is ready and correctly set for working.

The green led light is on after a few seconds, is the

time needed to carry on the self-checking system.

The green light is pulsing when the desoldering iron

is in sleep mode.

If the green led is not lit, the reason why, will be one

of the following:

1. The desoldering iron is not plugged in.

2. The maximum available power has been

exceeded for too long - e.g. in a very thick

desoldering at the high repetition rates.

3. The desoldering heating element has a short

circuit or an open circuit.

4. Any other trouble preventing the system from

working properly.

The handpiece will reset itself automatically should

the cartridge short circuit or go open circuit.

Should the handpiece be subject to:

- An electrical surge or the cartridge has not been

fitted correctly.

Please turn the unit off and switch on again to reset.

When pressing the button of the desoldering iron

handle, one of the two leds in the area marked

SUCTION will light up:

Green light -SUCTION- indicates the correct

functioning of the desoldering iron.

Red light -SUCTION- indicates a blockade within

the vacuum circuit.

This can be caused by the following:

- The tip of the desoldering iron is blocked.

Sleep function

One of the Series Advanced features is that when

the desoldering iron is placed in the holder, the

temperature at the tip drops automatically to the

sleep temperature. This function is only

possible because of the quick response time

which does not make the user realise the

temperature rise to reach the selected

temperature. Also by this, the oxidation of the

tinning of the tip is considerably reduced and

tip life is extended.

To indicate that the desoldering iron is in sleep-

mode, the green led starts pulsing. These

parameters can be modified using the Console

AC 2600 Ref. 2600000.

In order to take advantage of the above

mentioned feature and as a security measure,

it is necessary to place the desoldering iron

on stand when the iron is not being used.

DR 5600 Ref.5600000

Desoldering tip

Heating element

Pushbutton vacuum pump

Vacuum hose

Desoldering iron cable

Solder tin deposit

Metal

Glass

- The solder tin deposit is full.

- The filter of the desoldering iron is dirty.

- The station’s external desoldering air filter is

dirty.

Only for users of AC 2600 console ref. 2600000.

If you lock the working temperature thanks to the

console, the green LED -READY- will remain on

while the dial is set at the locked temperature.

If the dial is not set at the locked temperature,

the green LED -READY- will be blinking. The

farther the dial will be set from the locked

temperature the slower the blinking pace will be.

ENGLISH

11

RECOMMENDATIONS FOR USE

For soldering and desoldering

- Clean the contacts and the printed circuit to

be desoldered of dust or dirt.

- Preferably select a temperature below 350°C.

Excess temperature may cause the printed

circuit tracks to break loose.

- The tip must be well tinned for good heat

conduction. If it has been inoperative for any

length of time, it should be retinned.

Desoldering process

Use the tip model with a larger diameter than the

pad to be desoldered, so as to achieve maximum

aspiration and thermal efficiency.

1 Apply the desoldering iron tip so that the

component terminal penetrates within its

orifice.

2 When the solder liquefies, start gently to rotate

the desoldering tip so that the component’s

terminal can be eased away from the sides.

3 Press then, not before, the vacuum pump

push-button just long enough to aspirate the

solder.

After pressing the desoldering key there is a

slight delay until the self-contained vacuum

pump stops, this is to make sure that the

vacuum circuit is completely empty.

If any solder remains are left on any terminal after

attempting to desolder it, resolder it with fresh

solder and repeat the desoldering operation.

1

2

3

DESOLDERING TIPS

These tips are

specially designed

to clean the pads.

Ref. 5600-001 5600-002 5600-003 5600-004 5600-005 5600-006 5600-007

5600

A ø (mm)

B ø (mm)

max. pin ø

(mm)

001 / 011

1.4

0.6

0.4

002 / 012

1.8

0.8

0.6

003 / 013

2.7

1

0.8

004

3.2

1.3

1.1

005

3.4

1.6

1.4

006

4.2

2

1.7

007

4.8

2.5

2.3

A ø

B ø

5600-012 5600-0135600-011

12

ENGLISH

Change of desoldering tip

This operation should be done while the tip is hot,

at a minimum temperature of 250°C, so that any

tin left inside is in molten state.

- Unscrew the tip to be replaced, with the aid of

the spanner supplied.

- Fit the new tip, and tighten up with the spanner

to achieve a good air tightness.

To empty the solder tin deposit and change

the filter

For this, the lid needs to be unscrewed and first

the tin deposit and then its spiral must be removed

to clean the inner part of the deposit with a brush.

- The condition of the filter must be checked

and replaced if dirty or damaged.

- The deposit needs to be inserted with spiral

filter put into place. Then the whole must be

closed by screwing the lid shut.

Solder tin deposits

It can be chosen between two different deposit

types:

- Metal Ref. 0812630.

- Glass Ref. 0812620.

Lid

Brush

Ref. 0786640

Filter Ref.0780840

Deposit

Spiral

Ref. 0780550

Tip care

- The largest rod that fits in the tip hole should

periodically be passed through in order to

clean the intake tube.

- To clean the tips, use the sponge included

with the stand and check it is slightly moisted.

Only deionised water (car battery water)

should be used in order to wet the sponge.

If normal water was to be used, it is very likely

that the tip will become dirty due to the salts

dissolved within the water.

- Do not file the tips or use abrasive tools

which may damage the tip’s protective

surface coating and avoid knocking them

about.

- If the tip has been a long time without being

tinned, use a metal brush to remove any dirt

and oxid.

IMPORTANT: DO NOT press the pushbutton

vacuum pump while tinning the desoldering tip,

as the fumes given off by the flux would quickly

soil the ducts and filter of the air circuit.

ENGLISH

13

- Place the new heating element. Check that

the right extremity of the upper part of the

heating element is inserted in the slot

located inside the body of the desoldering

iron (see drawing hereunder).

- Screw out the body of the desoldering

iron. Open up the body and remove the

heating element.

- Screw in the body of the desoldering iron.

Put the spiral and the filter back into the

deposit. Place the deposit inside the body

of the desoldering iron and screw in the

shut lid.

Lid

Brush

Ref. 0786640

Filter Ref. 0780840

Deposit

Spiral

Heating element

Ref. 5600010

Change of the heating element of the

desoldering iron (Ref. 5600010)

- To realize this operation, the lid needs to

be unscrewed and first the tin deposit and

then its spiral and filter must be removed

to clean the inner part of the deposit with

a brush.

14

ENGLISH

Cleaning the vacuum pump valve

Open the control unit as follow:

- Disconnect the control unit.

- Turn it upside down, remove the fixing

screws.

- Return the station to its normal position and

lift up the lid.

- Undo the four screws fastening the pump cover.

- Clean the valve with a cloth dampened in

alcohol. If it is too soiled, replace it with new

one. Ref. 0982970.

Detecting air leaks in the circuit

To detect air leaks in the circuit:

- Obstruct the tip inlet orifice

by pressing down on a

silicone disc, or bend the

tube connecting the

desoldering iron to the filter.

- Press the pushbutton vacuum pump.

If the red led lights up, there is no loss of

suction. Otherwise air gets into the system at

some point. This can occur at the desoldering

tip, or may be caused by the lid of the deposit,

lids of filters or because the air pump does not

function correctly due to dirty valves which

occurs when the air filter has not been used

correctly.

Changing the pump inlet filter

Verify the filter at the entrance of the pump, and

change it if dirty or obstructed, therefor:

Open the filter pulling the flap.

Take out the 2 cotton filters, throw away those

which are soiled and replace them with new

ones. Always use 2 filters.

Close the filter and check the airtightness.

ENGLISH

15

PICK & PLACE PEN MP 2260

The pick & place pen MP 2260 ref. 2260000 for

the placing of SMD is also delivered with the AM

6000.

The pen is connected to the plug VACUUM of the

station. Please find the connection plan on page 1.

A set of straight and bent needles as well as a

set of different sized suction cups is delivered

with the station:

- Set of suction cups Ref. 0940163

- Set of straight needles Ref. 0901546

- Set of bent needles Ref. 0861660

The suction cups can be adjusted to the needles

in order to make the placement of SMD of different

sizes on boards easier.

These accessories allows the adjustment to weight

and size of any type of component.

Component pick-up (Fig. A)

Place the needle tip on the component and block

the control orifice with the first finger of the other

hand so that the component may be held to the

needle by suction.

Component placing (Fig. B)

Place the component in position on the printed

circuit. Remove your finger from the orifice

allowing air to enter whereby the component will

be released in the desired position.

Faults and remedies

We list below the most frequent faults and the

possible remedies which you yourself may be

able to apply. In any case, the JBC technical

assistance service will attend to you if required.

Insufficient suction

The tubes have to be checked for possible air

escapes and the correct connection of the tubes

to their terminals must be observed. Check the

incoming air filter in the interior of the station and

replace it if dirty or obstructed.

If in spite of this the suction is insufficient, the

self-contained vacuum pump should be checked.

Filter

Ref. 0861800

When you assemble the suction cup with the needle,

you should avoid the needle to stick out of the

lower part.

Fig. A

Fig. B

CUPS

Ref.: 0940163

STRAIGHT

NEEDLES

Ref.: 0901546

Ø A

mm

COLOR

2 x 4,3

BLACK

YELLOW2 x 7

PINK2 x 10

Ø B

mm

2 x 0,7

2 x 0,9

2 x 1,2

BENT

NEEDLES

Ref.: 0861660

COLOR

GREEN

YELLOW

PINK

Ø B

mm

2 x 0,8

2 x 0,9

2 x 1,2

16

ENGLISH

ADVANCED HANDPIECES RANGE

All the Advanced soldering handpieces range can

be connected to the AM 6000 station.

The station AM 6000 includes the following products:

- Handpiece 2245 ref. 2245000 with the cartridge

2245-003 Ref. 2245003. Power: 50W. For general

soldering work.

- Soldering iron stand AD 8200 ref. 0268200.

- Set of accessories ref. 0780593 with cartridge

2245-007 Ref. 2245007. It can be chosen from a

wide range of different cartridges 2245 to adapt

perfectly to the needs of the job (pag. 126).

The following soldering handpieces can be

connected to the AM 6000 station:

- Handpiece 2010 ref. 2010000. Power: 20W. For

high precision work, SMD etc. Available

cartridges 2010: see page 127.

- Handpiece 2210 ref. 2210000. Power: 20W. For

high precision work, SMD etc. Available

cartridges 2210: see page 127.

- Handpiece 2045 ref. 2045000. Power: 50W. For

general soldering work. Available cartridges

2045: see page 126.

Two versions of soldering iron handpieces covered

with heat isolater are available:

- 2045 Thermo-isolated handpiece ref. 2045110.

- 2245 Thermo-isolated handpiece ref. 2245110.

These articles are not delivered with the station.

The handpieces and cartridges 2210 and 2245

comply with the MIL-SPEC-2000 referring to the

potential difference between the soldering tip and

ground connection, must be less than 2 mV.

For a soldering handpiece to work properly, the

following components are required: control unit,

soldering iron stand, one handpiece and one

cartridge.

The soldering iron is connected to the station in the

following way:

The cable connection of the soldering iron is

connected to the plug in the soldering iron stand

AD 8200 and the cable connection of the soldering

iron stand is plugged into the terminal SOLD of the

station. Please find the connection plan on figure.

Soldering iron stand

AD 8200

Ref.0268200

Handpiece 2010 Ref. 2010000

Handpiece 2210 Ref. 2210000

Handpiece 2045 Ref. 2045000

Handpiece 2245 Ref. 2245000

Cartridges 2045

Cartridges 2245

Cartridges 2010

Cartridges 2210

Soldering

connector

SOLD

ENGLISH

17

Sleep function

One of the Series Advanced features is that when

the handpiece is placed in the holder, the

temperature at the tip drops automatically to the

sleep temperature. This function is only possible

because of the quick response time which does

not make the user realise the temperature rise to

reach the selected temperature. Also by this, the

oxidation of the tinning of the tip is considerably

reduced and tip life is extended.

To indicate that the soldering iron is in sleep-mode,

the green led starts pulsing. These parameters can

be modified using the Console AC 2600 Ref. 2600000.

In order to take advantage of the above

mentioned feature and as a security measure,

it is necessary to place the handpiece on stand

when the iron is not being used.

When connecting an old version solder stand, it may

happen that the sleep function does not work.

To resolve this problem, you should make a bridge

between pins number 3 and 5 from the aerial

connector of the cable of the stand, that plugs in

the station.

Aerial connector

Bridge between

pin number 3 & 5

OPERATION

LED lights

Red LED -ON- when lit, it indicates that the station is

plugged in the mains.

Green LED -READY- when lit, it indicates that the

system is ready and correctly set for working.

The green led light is on after a few seconds, is the

time needed to carry on the self-checking system.

The green light is pulsing when the soldering iron is

in sleep mode.

If the green led is not lit, the reason why, will be one

of the following:

1. The handpiece or the cartridge are not plugged

in.

2. The maximum available power has been

exceeded for too long - e.g. in a very thick

soldering at the high repetition rates.

3. The handpiece or cartridge has a short

circuit or an open circuit.

4. Any other trouble preventing the system from

working properly.

The green led goes off when the cartridge tip

touches the extractor and the station stops the

power supply.

The handpiece will reset itself automatically should

the cartridge short circuit or go open circuit.

Should the handpiece be subject to:

- An electrical surge or the cartridge has not been

fitted correctly.

Please turn the unit off and switch on again to

reset.

Only for users of AC 2600 console ref. 2600000.

If you lock the working temperature thanks to the

console, the green LED -READY- will remain on

while the dial is set at the locked temperature.

If the dial is not set at the locked temperature,

the green LED -READY- will be blinking. The

farther the dial will be set from the locked

temperature the slower the blinking pace will be.

18

ENGLISH

Alignment

XX

XXXXX

Important.

- It is essential to insert the cartridge till the end

for a good connection. Take the mark a s

reference.

Advanced series cartridge

Cartridge is made of the heating element which has the

heating system, temperature sensor and long life tip.

Long-life tip is basically made of:

1 Copper

2 Iron

3 Chromium

4 Tin plate

Long-life tip care

Except for the copper core, the rest of metals are

placed galvanically on layers relatively thin, so it

is necessary to avoid the reasons which can

cause its destruction.

To clean the tips, use the sponge included with

the stand and check it is slightly moisted.

Only deionised water (car battery water)

should be used in order to wet the sponge. If

normal water was to be used, it is very likely that

the tip will become dirty due to the salts dissolved

within the water.

To re-tin the soldering tips, we recommend using

the tip tinner/cleaner TT 9400 ref. 9400000.

2 - Place the handpiece on top of the new cartridge,

press it slightly down and remove the handpiece.

Changing the handpiece's cartridge

With the Advanced system, the cartridge can be

changed quickly, without turning off the station,

so you have two soldering irons in one. Here is

what to do to change the cartridge:

1 - Place the handpiece and remove the cartridge.

3 - Press the cartridge into the opening A, B or C:

A. For straight cartridges 2010 and 2210.

B. For curved cartridges 2010 and 2210.

C. For cartridges 2045 and 2245.

ENGLISH

19

Console AC 2600

The console AC 2600 is designed for modifying the

original regulation program parameters of the following

Advanced control units:

- AD 2000 soldering station.

- AD 2200 soldering station.

- AD 4200 and AD 4300 dual soldering stations.

- AR 5500, AR 5800 (*) and DS 5300 (*) desoldering

stations.

- AM 6000 and AM 6500 (*) rework stations.

(*) These stations need a console whose

program version is 4.0 or higher.

Changes avalaible to perform:

- Fixing the the working temperature.

- Selection of temperature units in Celsius grades

-°C- or Fahrenheit -°F-.

- Modification of sleep temperatures and standby

times.

- Adjustment of temperature.

- Set the parameters back to the original parameters.

- Read-out data:

Working hours.

Sleep cycles and sleep hours.

Cartridge and iron changes.

Program version.

Fume extractor accessories

Specially designed for the Advanced Series

handpieces 2010/2210 and 2045/2245. Easily clips

onto the handpiece and can be quickly removed

for easy maintenance.

AC 2600

Ref. 2600000

For handpieces 2045/2245:

Standard Ref.0495000

+20mm longer Ref.0455002

For handpieces 2010/2210

Ref.0265000

La page charge ...

jbc AM 6000 Manuel utilisateur

jbc AM 6000 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents