Simplicity 020583-00 Manuel utilisateur

Marque: Simplicity

Modèle: 020583-00

Catégorie: Nettoyeurs haute pression

Taper: Manuel utilisateur

Manual No. 80008206 Revision -

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

MILWAUKEE, WISCONSIN, U.S.A.

Pressure Washer

Operator’s Manual

This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA)

standard PW101-2010 (Testing and Rating Performance of Pressure Washers).

2 www.diamondpowerproducts.com

Thank you for purchasing this quality-built DIAMOND™ pressure washer. We are pleased that you’ve placed your confidence

in the DIAMOND brand. When operated and maintained according to the instructions in this manual, your DIAMOND pressure

washer will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with pressure washers and

how to avoid them. Because Briggs & Stratton does not necessarily know all the applications this pressure washer could be

used for, it is important that you read and understand these instructions thoroughly before attempting to start or operate this

equipment. Save these original instructions for future reference.

This pressure washer requires final assembly before use. Refer to the Assembly section of this manual for instructions on

final assembly procedures. Follow the instructions completely.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your pressure washer. Consult your Yellow Pages.

There are over 30,000 Briggs & Stratton authorized service dealers worldwide who provide quality service. You can also contact

Briggs & Stratton Customer Service by phone at (800) 743-4115, or on the Internet at www.diamondpowerproducts.com. For

engine related questions, call American Honda Motor Company, Inc. at (800) 426-7701 or visit www.honda-engines.com for a

dealer locator.

Pressure Washer

Model Number

Revision

Serial Number

Date Purchased

DIAMOND is a trademark of Briggs & Stratton Power Products Group

Milwaukee, WI, USA

Table of Contents

Operator Safety .................................4

Equipment Description.........................................4

Important Safety Information....................................4

Assembly .....................................7

Unpack Pressure Washer.......................................7

Attach Handle................................................7

Add Engine Oil and Fuel........................................7

Lubricate O-Rings ............................................8

Connect Hose and Water Supply to Pump..........................9

Checklist Before Starting Engine .................................9

Features and Controls............................ 10

Operation .................................... 11

Pressure Washer Location.....................................11

How to Start Your Pressure Washer .............................11

How to Stop Your Pressure Washer .............................12

How to Use Spray Tips .......................................13

Applying Detergent...........................................13

Pressure Washer Rinsing......................................14

Cleaning Detergent Siphoning Tube..............................14

Automatic Cool Down System (Thermal Relief).....................14

Maintenance .................................. 15

Pressure Washer Maintenance..................................15

Pump Oil Maintenance........................................17

Engine Maintenance..........................................17

After Each Use ..............................................18

Winter Storage..............................................19

Long Term Storage ..........................................19

Troubleshooting................................ 20

Warranty..................................... 21

Pressure Washer Owner Warranty...............................21

Specifications ................................. 22

Product Specifications ........................................22

Common Service Parts .......................................22

4 www.diamondpowerproducts.com

Operator Safety

Equipment Description

Read this manual carefully and become familiar

with your pressure washer. Know its applications,

its limitations, and any hazards involved.

This pressure washer operates at 3,400 PSI (234 BARS) and

a flow rate of 3.6 gallons per minute (13.62 liters per minute).

This high quality residential system features a triplex pump with

stainless steel pistons, automatic cool down system, detergent

siphoning system, nozzle extension with quick connect fitting,

a variety of quick connect spray tips, heavy duty 30’ (9.14 m)

hose, and more.

Every effort has been made to ensure that information in this

manual is accurate and current. However, we reserve the right

to change, alter, or otherwise improve the product and this

document at any time without prior notice.

The Emission Control System for this pressure washer is

warranted for standards set by the Environmental Protection

Agency and the California Air Resources Board.

Important Safety Information

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a

degree or level of hazard seriousness. A safety symbol may

be used to represent the type of hazard. The signal word

NOTICE is used to address practices not related to personal

injury.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE address practices not related to personal injury.

Fire

Explosion

Toxic Fumes

Hot Surface

Moving Parts

Electrical Shock

Slippery Surface

Fall

Kickback

Flying Objects

Fluid Injection

Operator’s Manual

Chemical Burn

Projectile

WARNING The engine exhaust from this product

contains chemicals known to the State of California to

cause cancer, birth defects, or other reproductive harm.

WARNING This product contains lead and lead

compounds, known to the State of California to cause

birth defects or other reproductive harm. Wash your

hands after handling this product.

WARNING Risk of electrocution.

Contact with power source could cause electric

shock or burn resulting in death or serious injury.

• NEVER spray near power source.

WARNING Fuel and its vapors are extremely flammable

and explosive which could cause burns,

fire or explosion resulting in death or

serious injury.

WHEN ADDING OR DRAINING FUEL

• Turn pressure washer engine OFF and let it cool at least 2

minutes before removing fuel cap. Loosen cap slowly to relieve

pressure in tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• Check fuel lines, tank, cap and fittings frequently for cracks or

leaks. Replace if necessary.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap, and air cleaner are in place.

• DO NOT crank engine with spark plug removed.

WHEN OPERATING EQUIPMENT

• DO NOT operate this product inside any building, carport,

porch, mobile equipment, marine applications, or enclosure.

• DO NOT tip engine or equipment at angle which causes fuel to

spill.

• DO NOT spray flammable liquids.

WHEN TRANSPORTING, MOVING OR REPAIRING EQUIPMENT

• Transport/move/repair with fuel tank EMPTY or with fuel shutoff

valve OFF.

• DO NOT tip engine or equipment at angle which causes fuel to

spill.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers, or other appliances that have pilot light or other ignition

source because they could ignite fuel vapors.

WARNING Starter cord kickback (rapid retraction)

will pull hand and arm toward engine faster than

you can let go which could cause broken bones,

fractures, bruises, or sprains resulting in serious

injury.

• NEVER pull starter cord without first relieving spray gun pressure.

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• After each starting attempt, where engine fails to run, always

point spray gun in safe direction, press red button and squeeze

spray gun trigger to release high pressure.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

WARNING Chemical Burn Hazard.

Chemicals could cause burns resulting in death

or serious injury.

• DO NOT use caustic liquid with pressure washer.

• Use ONLY pressure washer safe detergents/soaps. Follow all

manufacturers instructions.

WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting in serious

injury and possible amputation.

Spray gun traps high water pressure, even when engine is

stopped and water is disconnected, which could result in

serious injury.

• If cut by fluid, call physician immediately. DO NOT treat as a

simple cut.

• DO NOT allow CHILDREN to operate pressure washer.

• NEVER repair high pressure hose. Replace it.

• NEVER repair leaking connections with sealant of any kind.

Replace o-ring or seal.

• NEVER connect high pressure hose to nozzle extension.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction, press red button

and squeeze spray gun trigger to release high pressure, every

time you stop engine.

• NEVER aim spray gun at people, animals, or plants.

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while machine is running.

• NEVER use a spray gun which does not have a trigger lock or

trigger guard in place and in working order.

• Always be certain spray gun, nozzles and accessories are

correctly attached.

WARNING POISONOUS GAS HAZARD. Engine

exhaust contains carbon monoxide, a

poisonous gas that could kill you in minutes.

You CANNOT smell it, see it, or taste it. Even

if you do not smell exhaust fumes, you could

still be exposed to carbon monoxide gas.

Some chemicals or detergents could be harmful if inhaled

or ingested, resulting in death, serious injury, nausea,

fainting or poisoning.

• Operate this product ONLY outside far away from windows,

doors and vents to reduce the risk of carbon monoxide gas

from accumulating and potentially being drawn towards

occupied spaces.

• Install battery-operated carbon monoxide alarms or plug-in

carbon monoxide alarms with battery back-up according to

the manufacturer’s instructions. Smoke alarms cannot detect

carbon monoxide gas.

• DO NOT run this product inside homes, garages, basements,

crawlspaces, sheds, or other partially-enclosed spaces even

if using fans or opening doors and windows for ventilation.

Carbon monoxide can quickly build up in these spaces and can

linger for hours, even after this product has shut off.

• ALWAYS place this product downwind and point the engine

exhaust away from occupied spaces.

If you start to feel sick, dizzy, or weak while using this product,

shut it off and get to fresh air RIGHT AWAY. See a doctor. You

may have carbon monoxide poisoning.

• Use a respirator or mask whenever there is a chance that

vapors may be inhaled when using chemicals.

• Read all instructions with mask so you are certain the mask

will provide the necessary protection against inhaling harmful

vapors when using chemicals.

6 www.diamondpowerproducts.com

NOTICE High pressure spray could damage fragile items

including glass.

• DO NOT point spray gun at glass when using red (0°) spray tip.

• NEVER aim spray gun at plants.

NOTICE Improper treatment of pressure washer could

damage it and shorten its life.

• If you have questions about intended use, ask dealer or contact

qualified service center.

• NEVER operate units with broken or missing parts, or without

protective housing or covers.

• DO NOT by-pass any safety device on this machine.

• DO NOT tamper with governed speed.

• DO NOT operate pressure washer above rated pressure.

• DO NOT modify pressure washer in any way.

• Before starting pressure washer in cold weather, check all parts of

the equipment to be sure ice has not formed there.

• NEVER move machine by pulling on hoses. Use handle provided

on unit.

• This equipment is designed to be used with Briggs & Stratton

Power Products authorized parts ONLY. If equipment is used with

parts that DO NOT comply with minimum specifications, user

assumes all risks and liabilities.

WARNING Unintentional sparking could cause fire or

electric shock resulting in death or

serious injury.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR PRESSURE

WASHER

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

WARNING Starter and other rotating parts could

entangle hands, hair, clothing, or accessories

resulting in serious injury.

• NEVER operate pressure washer without protective housing or

covers.

• DO NOT wear loose clothing, jewelry or anything that could be

caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

CAUTION

Excessively high operating speeds could

result in minor injury.

Excessively low speeds impose a heavy load.

• DO NOT tamper with governor spring, links or other parts to

increase engine speed. Pressure washer supplies correct rated

pressure and flow when running at governed speed.

• DO NOT modify pressure washer in any way.

WARNING Risk of eye or bodily injury.

Spray could splash back or propel

objects resulting in serious injury.

• Always wear indirect vented (chemical splash) safety goggles

marked to comply with ANSI Z87.1 when using or in vicinity of

this equipment.

• NEVER substitute safety glasses or dry-condition goggles for

indirect vented safety goggles.

• Always wear protective clothing such as a long-sleeved shirt,

long pants and close-toed shoes.

• NEVER operate pressure washer when barefoot or wearing

sandals or shorts.

WARNING Use of pressure washer could create puddles

and slippery surfaces causing you to fall

resulting in death or serious injury.

Kickback from spray gun could cause

you to fall resulting in death or serious injury.

• Operate pressure washer from a stable surface.

• The cleaning area should have adequate slopes and drainage to

reduce the possibility of a fall due to slippery surfaces.

• Be extremely careful if you must use the pressure washer from

a ladder, scaffolding, or any other similar location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage fuel

tank causing a fire, resulting in death or

serious injury.

Contact with muffler area could cause burns resulting in

serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5ft. (1.5 m) of clearance on all sides of pressure

washer including overhead.

• It is a violation of California Public Resource Code, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in Section

4442, maintained in effective working order. Other states or

federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer

to obtain a spark arrester designed for the exhaust system

installed on this engine.

• Replacement parts must be the same and installed in the same

position as the original parts.

Assembly

Read entire operator’s manual before you attempt

to assemble or operate your new pressure washer.

Your pressure washer requires some assembly and is

ready for use after it has been properly serviced with the

recommended oil and fuel.

If you have any problems with the assembly of your

pressure washer, please call the pressure washer helpline

at (800)743-4115. If calling for assistance, please have the

model, revision, and serial number from the identification

label available.

Unpack Pressure Washer

1. Remove the parts bag, accessories, and inserts

included with pressure washer.

2. Open carton completely by cutting each corner from

top to bottom.

3. Ensure you have all included items prior to assembly.

Items in the carton include:

• Main Unit

• Handle

• High Pressure Hose

• Spray Gun

• Nozzle Extension with Quick Connect Fitting

• Engine Operator’s Manual

• Oil Pouch (2)

• Parts Bag (which includes the following):

• Operator’s Manual

• Owner’s Registration Card

• Bag of 5 Multi–Colored Spray Tips

• Handle Fastening Hardware Kit (which includes):

• Carriage Bolts (2)

• Plastic Knobs (2)

To prepare your pressure washer for operation, you will

need to perform these tasks:

1. Fill out and send in registration card.

2. Attach handle to main unit.

3. Verify pump oil dipstick (A) has been installed into

pump.

4. Add oil to engine crankcase.

5. Add fuel to fuel tank.

6. Connect high pressure hose to spray gun and pump.

7. Connect water supply to pump.

8. Attach nozzle extension to spray gun.

9. Select/attach quick connect spray tip to nozzle

extension.

Attach Handle

1. Place handle (B) onto handle supports (C) connected

to main unit. Make sure holes (D) in handle align with

holes (D) on handle supports.

NOTICE It may be necessary to move the handle supports

from side to side in order to align the handle so it will slide

over the handle supports.

2. Insert carriage bolts (E) through holes from back of

unit and attach a plastic knob (F) from front of unit.

Tighten by hand.

3. Insert multi-colored quick connect spray tips and other

supplied accessories in spaces provided on handle.

Add Engine Oil and Fuel

• Place pressure washer on a level surface.

NOTICE Any attempt to crank or start the engine before

it has been properly filled with the recommended oil will

result in equipment failure.

• Refer to engine manual for oil and fuel fill information.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

• Refer to engine operator’s manual and follow oil and

fuel recommendations and instructions.

NOTICE Check oil often during engine break–in. Refer to

engine operator’s manual for recommendations.

8 www.diamondpowerproducts.com

Lubricate O-Rings

Lubrication of o-rings is extremely important for installation

and operation. The use of a lubricant (petroleum or synthetic

grease) during assembly helps seat o-rings properly and

provides an improved seal. It also helps protect the o-ring

from damage by abrasion, pinching or cutting and extends

the life of the o-ring.

NOTICE ALWAYS apply a small amount of lubricant on

o-rings prior to assembling the garden hose to the pump

inlet(A), high pressure hose (B), nozzle extension (C), and

spray gun(D).

Lubricate all connections shown below, following these

instructions:

1. Inspect and clean connecting surfaces prior to

lubrication and assembly.

2. Use lubricants sparingly during assembly; a light film is

all that is required.

3. Use a small brush or cotton swab to apply grease

directly to o-rings where they are not accessible

(QC fitting, M22 fitting).

Connect Hose and Water Supply to Pump

NOTICE DO NOT run the pump without the water supply

connected and turned on.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

NOTICE Remove and discard the shipping caps from the

pump’s high pressure outlet and water inlet before attaching

hoses.

1. Uncoil high pressure hose and attach one end of hose

to base of spray gun. Tighten by hand.

2. Attach other end of high pressure hose to high pressure

outlet (A) on pump. Tighten by hand.

3. Run water through your garden hose for 30seconds to

clean out any debris.

NOTICE DO NOT siphon standing water for the water

supply. Use ONLY cold water (less than 100°F (38°C)).

4. Before connecting garden hose to water inlet, inspect

inlet screen (B). Clean screen if it contains debris or

have it replaced if damaged. DO NOT run pressure

washer if inlet screen is damaged.

5. Connect the garden hose (not to exceed 50ft.(15.24 m) in

length) to the water inlet. Tighten by hand.

NOTICE Using a One Way Valve (vacuum breaker or check

valve) at pump inlet can cause pump or inlet connector

damage.

• There MUST be at least ten feet of unrestricted garden hose

between the pressure washer inlet and any device, such as a

vacuum breaker or check valve.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

6. Turn on the water, press red button (C) on the gun and

squeeze the trigger to purge the pump system of air and

impurities.

Checklist Before Starting Engine

Review the unit’s assembly to ensure you have performed all

of the following.

1. Be sure to read Operator Safety and Operation sections

before using pressure washer.

2. Make sure handle is in place and secure.

3. Check that oil has been added to proper level in the

engine crankcase.

4. Add proper fuel to fuel tank.

5. Check for properly tightened hose connections.

6. Check to make sure there are no kinks, cuts, or damage

to high pressure hose.

7. Provide a proper water supply at an adequate flow.

WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting in serious

injury and possible amputation.

• NEVER connect high pressure hose to nozzle extension.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• Always be certain spray gun, nozzles and accessories are

correctly attached.

WARNING Risk of eye injury.

Spray could splash back or propel objects

resulting in serious injury.

• Always wear indirect vented (chemical splash) safety goggles

marked to comply with ANSI Z87.1 when using or in vicinity of

this equipment.

• NEVER substitute safety glasses or dry-condition goggles for

indirect vented safety goggles.

10 www.diamondpowerproducts.com

Features and Controls

Read this Operator’s Manual and safety rules before operating your pressure washer.

Compare the illustrations with your pressure washer, to familiarize yourself with the locations of various controls and

adjustments. Save this manual for future reference.

A - High Pressure Hose — Connect one end to water pump

and the other end to spray gun.

B - Spray Tips — Detergent, 0°, 15°, 25° and 40°: for

various high pressure cleaning applications.

C - Warning/Operating Instructions Tag — Identifies hazards

and proper procedure to start/stop pressure washer.

D - Air Filter — Protects engine by filtering dust and debris

out of intake air.

E - Throttle Lever — Sets engine in starting mode for recoil

start.

F - Choke Lever — Prepares a cold engine for starting.

G - Fuel Valve — Used to turn fuel supply on and off to

engine.

H - Recoil Starter — Used for starting the engine manually.

J - Engine Switch — Set switch to “On” for recoil starting.

Set switch to “Off” to stop a running engine.

K - Nozzle Extension with Quick Connect — Allows you to

switch between five different spray tips.

L - Pressure Control Knob — Varies pressure of high

pressure spray.

M - Water Inlet — Connection for garden hose.

N - High Pressure Outlet — Connection for high pressure

hose.

P - Detergent Siphoning Tube/Filter — Use to siphon

pressure washer safe detergent into the low pressure

stream.

R - Oil Drain Plug — Drain engine oil here.

S - Pump — Develops high pressure.

T - Automatic Cool Down System — Cycles water through

pump when water reaches 125°-155°F. Warm water will

discharge from pump onto ground. This system prevents

internal pump damage.

U - Fuel Tank — Fill tank with regular unleaded fuel. Always

leave room for fuel expansion.

V - Spray Gun — Controls the application of water onto

cleaning surface with trigger device. Includes automatic

trigger lock.

Items Not Shown:

Identification Label (near rear of base plate) — Provides

model and serial number of pressure washer. Please have

these numbers readily available if calling for assistance.

Oil Fill/Dipstick — Check and add engine oil here.

Operation

If you have any problems operating your pressure washer,

please call the pressure washer helpline at (800) 743-4115.

Pressure Washer Location

Carbon Monoxide Poisoning

Risk of Fire Clearances

How to Start Your Pressure Washer

To start your pressure washer for the first time, follow these

instructions step-by-step. This starting information also

applies if you have let the pressure washer sit idle for at least

a day.

1. Place pressure washer near an outside water source

capable of supplying water at a flow rate greater than

4.6 gallons (17.4 l) per minute and no less than 20PSI

(1.38 BARS) at pressure washer end of garden hose.

DO NOT siphon supply water.

2. Check that high pressure hose is tightly connected to

spray gun and pump. See Assembly section.

3. Make sure unit is in a level position.

4. Connect garden hose to water inlet on pressure washer

pump.

NOTICE DO NOT run the pump without the water supply

connected and turned on.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

5. Turn on the water, press red button on the gun and

squeeze the trigger to purge the pump system of air and

impurities.

6. Attach nozzle extension to spray gun. Tighten by hand.

7. Choose spray tip you want to use, pull back on collar of

nozzle extension, insert spray tip and release collar. Tug

on spray tip to make sure it is securely in place. See

How to Use Spray Tips.

NOTICE Before starting the pressure washer, be sure you

are wearing safety goggles as described below.

WARNING Risk of eye injury.

Spray could splash back or propel objects

resulting in serious injury.

• Always wear indirect vented (chemical splash) safety goggles

marked to comply with ANSI Z87.1 when using or in vicinity of

this equipment.

• NEVER substitute safety glasses or dry-condition goggles for

indirect vented safety goggles.

WARNING POISONOUS GAS HAZARD. Engine

exhaust contains carbon monoxide, a poisonous

gas that could kill you in minutes. You CANNOT

smell it, see it, or taste it. Even if you do not

smell exhaust fumes, you could still be exposed to carbon

monoxide gas.

• Operate this product ONLY outside far away from windows,

doors and vents to reduce the risk of carbon monoxide gas

from accumulating and potentially being drawn towards

occupied spaces.

• Install battery-operated carbon monoxide alarms or plug-in

carbon monoxide alarms with battery back-up according to

the manufacturer’s instructions. Smoke alarms cannot detect

carbon monoxide gas.

• DO NOT run this product inside homes, garages, basements,

crawlspaces, sheds, or other partially-enclosed spaces even

if using fans or opening doors and windows for ventilation.

Carbon monoxide can quickly build up in these spaces and can

linger for hours, even after this product has shut off.

• ALWAYS place this product downwind and point the engine

exhaust away from occupied spaces.

If you start to feel sick, dizzy, or weak while using this product,

shut it off and get to fresh air RIGHT AWAY. See a doctor. You

may have carbon monoxide poisoning.

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage fuel tank

causing a fire, resulting in death or serious injury.

• Keep at least 5ft. (1.5 m) clearance on all sides of pressure

washer including overhead.

Exhaust port

pointed away from

occupied spaces

12 www.diamondpowerproducts.com

8. When starting engine, position yourself as recommended

and start engine according to instructions given in engine

operator’s manual. Also see operating instructions tag located

on the pressure washer.

9. Point spray gun in a safe direction, push the red button

(A) to release the trigger lock, and pull the trigger.

NOTICE Always keep the throttle lever in the “Fast” position

when operating the pressure washer.

How to Stop Your Pressure Washer

1. Release spray gun trigger and let engine idle for two

minutes.

2. Turn engine off according to instructions given in

engine operator’s manual.

3. ALWAYS point spray gun in a safe direction, press

red button and squeeze spray gun trigger to release

retained high water pressure.

WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting in serious

injury and possible amputation.

Spray gun traps high water pressure, even when engine is

stopped and water is disconnected, which could result in

serious injury.

• DO NOT allow CHILDREN to operate pressure washer.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• NEVER aim spray gun at people, animals, or plants.

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while machine is running.

• NEVER use a spray gun which does not have a trigger lock or

trigger guard in place and in working order.

• Always be certain spray gun, nozzles and accessories are

correctly attached.

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage fuel

tank causing a fire, resulting in death or

serious injury.

Contact with muffler area could cause burns resulting in

serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5ft. (1.5 m) of clearance on all sides of pressure

washer including overhead.

• It is a violation of California Public Resource Code, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in Section

4442, maintained in effective working order. Other states or

federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer

to obtain a spark arrester designed for the exhaust system

installed on this engine.

• Replacement parts must be the same and installed in the same

position as the original parts.

WARNING Starter cord kickback (rapid retraction) will

pull hand and arm toward engine faster than you

can let go which could cause broken bones,

fractures, bruises, or sprains resulting in serious

injury.

• NEVER pull starter cord without first relieving spray gun

pressure.

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• After each starting attempt, where engine fails to run, always

point spray gun in safe direction, press red button and squeeze

spray gun trigger to release high pressure.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting in serious

injury and possible amputation.

Spray gun traps high water pressure, even when engine is

stopped and water is disconnected, which could result in

serious injury.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction, press red button

and squeeze spray gun trigger to release high pressure, every

time you stop engine.

How to Use Spray Tips

The quick–connect on the nozzle extension allows you to

switch between five different quick connect spray tips. Spray

tips can be changed while pressure washer is running once

spray gun trigger lock is engaged. The spray tips vary the

spray pattern as shown below.

Follow these instructions to change spray tips:

1. Pull back collar on quick–connect and pull current

spray tip off. Store spray tips in holes provided on the

handle.

2. Select desired spray tip:

• For gentle rinse, select white 40° or green 25° spray tip.

• To scour surface, select yellow 15° or red 0° spray tip.

• To apply detergent, select black spray tip.

3. Pull back on collar, insert new spray tip and release collar.

Tug on spray tip to make sure it is securely in place.

Usage Tips

• For most effective cleaning, keep spray tip from 8to

24inches (20 to 61 cm) away from cleaning surface.

• If you get spray tip too close, especially using a high

pressure spray tip, you may damage surface being

cleaned.

• DO NOT get closer than 6 inches (15 cm) when

cleaning tires.

Applying Detergent

To apply detergent, follow these steps:

1. Review use of spray tips.

2. Prepare detergent solution as required by job.

3. Place small filter end of detergent siphoning tube into

detergent container.

NOTICE Make sure the filter is fully submerged in detergent

while applying detergent.

NOTICE Contact with the hot muffler could damage

detergent siphoning tube.

• When inserting the siphon into a detergent solution bottle, route

the tube so as to keep it from inadvertently contacting the hot

muffler.

4. Make sure black spray tip is installed.

NOTICE Detergent cannot be applied with the high pressure

spray tips (White, Green, Yellow or Red).

5. Make sure garden hose is connected to water inlet.

Check that high pressure hose is connected to spray

gun and pump. Turn on water.

NOTICE You must attach all hoses before you start the

engine.

• Starting the engine without all the hoses connected and without

the water turned ON could damage the pump.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

White

40°

Green

25°

Black Yellow

15°

Red

0°

Low Pressure

Use to apply

detergent

High

Pressure

WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting in serious

injury and possible amputation.

• NEVER exchange nozzles without the trigger lock being

engaged on the spray gun.

• DO NOT twist nozzles while spraying.

WARNING Chemical Burn Hazard.

Chemicals could cause burns resulting in death

or serious injury.

• DO NOT use caustic liquid with pressure washer.

• Use ONLY pressure washer safe detergents/soaps. Follow all

manufacturers instructions.

14 www.diamondpowerproducts.com

6. Start engine following instructions How to Start Your

Pressure Washer.

7. Apply detergent to a dry surface, starting at lower

portion of area to be washed and work upward, using

long, even, overlapping strokes.

8. Allow detergent to “soak in” for 3-5 minutes before

washing and rinsing. Reapply as needed to prevent

surface from drying. DO NOT allow detergent to dry on

(prevents streaking).

NOTICE You must flush the detergent siphoning system

after each use by placing the filter into a bucket of clean

water, then run the pressure washer in low pressure for

1-2minutes.

Pressure Washer Rinsing

For Rinsing:

1. Remove black spray tip from nozzle extension.

2. Select and install desired high pressure spray tip

following instructions How to Use Spray Tips.

3. Keep the spray gun a safe distance from the area you

plan to spray.

4. Increase (decrease) spray pressure by turning pressure

control knob (A) clockwise (counterclockwise). Use lower

pressure to wash items such as a car or boat. Use higher

pressure to strip paint and degrease driveways.

5. Apply a high pressure spray to a small area and then

check surface for damage. If no damage is found, you

can assume it is okay to continue rinsing.

6. Start at top of area to be rinsed, working down with

same overlapping strokes as you used for cleaning.

Cleaning Detergent Siphoning Tube

If you used the detergent siphoning tube, you must flush it

with clean water before stopping the engine.

1. Place detergent siphoning tube/filter in a bucket full of

clean water.

2. Remove high pressure spray tip from nozzle extension.

3. Select and install black detergent spray tip following

instructions How to Use Spray Tips.

4. Flush for 1-2 minutes.

5. Shut off engine following instructions How to Stop

Pressure Washer and turn off water supply.

6. ALWAYS point spray gun in a safe direction, press

red button and squeeze spray gun trigger to release

retained high water pressure.

Automatic Cool Down System (Thermal Relief)

If you run the engine on your pressure washer for 3-5 minutes

without pressing the trigger on the spray gun, circulating

water in the pump can reach temperatures above 125°F to

155°F (51°C to 68°C). The system engages to cool the pump

by discharging the warm water onto the ground.

WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting in serious

injury and possible amputation.

Spray gun traps high water pressure, even when engine is

stopped and water is disconnected, which could result in

serious injury.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction, press red button

and squeeze spray gun trigger to release high pressure, every

time you stop engine.

WARNING Kickback from spray gun could cause you

to fall resulting in death or serious injury.

• Operate pressure washer from a stable surface.

• Be extremely careful if you must use the pressure washer from

a ladder, scaffolding, or any other similar location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

Maintenance

General Recommendations

Regular maintenance will improve the performance and

extend the life of the pressure washer. See any qualified

dealer for service.

The pressure washer’s warranty does not cover items that

have been subjected to operator abuse or negligence. To

receive full value from the warranty, the operator must

maintain the pressure washer as instructed in this manual,

including proper storage as detailed in Winter Storage and

Long Term Storage.

NOTICE Should you have questions about replacing

components on your pressure washer, please call

(800)743-4115 for assistance.

• Some adjustments will need to be made periodically

to properly maintain your pressure washer. Check the

spray gun and nozzle extension assembly for wear.

• All maintenance in this manual and the engine operator’s

manual should be made at least once each season.

• Once a year you should clean or replace the spark plug,

clean or replace the air filter. A new spark plug and

clean air filter assure proper fuel-air mixture and help

your engine run better and last longer. Please refer to

your engine operator’s manual for more details.

Before Each Use

1. Check engine oil level.

2. Clean debris.

3. Check water inlet screen for damage.

4. Check high pressure hose for leaks.

5. Check detergent siphoning tube/filter for damage.

6. Check spray gun and nozzle extension for leaks.

7. Rinse out garden hose to flush out debris.

Pressure Washer Maintenance

Clean Debris

Daily or before use, clean accumulated debris from cleaning

system. Keep linkage, spring and controls clean. Keep area

around and behind muffler free from any combustible debris.

Inspect cooling air slots and openings on the pressure washer.

These openings must be kept clean and unobstructed.

Cleaning system parts should be kept clean to reduce the

risk of overheating and ignition of accumulated debris.

• Use a damp cloth to wipe exterior surfaces clean.

NOTICE Improper treatment of pressure washer could

damage it and shorten its life.

• DO NOT insert any objects through cooling slots.

• Use a soft bristle brush to loosen caked on dirt, oil, etc.

• Use a vacuum cleaner to pick up loose dirt and debris.

Check and Clean Inlet Screen

Examine the screen on the pump’s water inlet. Clean it if the

screen is clogged or replace it if screen is damaged.

Check High Pressure Hose

The high pressure hose can develop leaks from wear,

kinking, or abuse. Inspect the hose each time before using it.

Check for cuts, leaks, abrasions or bulging of cover, damage

or movement of couplings. If any of these conditions exist,

replace the hose immediately.

Check Detergent Siphoning Tube

Examine the filter on the detergent tube and clean if clogged.

The tube should fit tightly on the barbed fitting. Examine the

tube for leaks or tears. Replace the filter or tube if either is

damaged.

Detergent Siphoning Check Ball

Occasionally check ball in detergent siphoning system may

become stuck from storage, dried soap, or minerals in water.

The check ball can be freed by performing the following:

NOTICE Before performing this procedure, be sure you are

wearing safety goggles as described below.

1. Shut off engine and turn off water supply.

2. ALWAYS point spray gun in a safe direction, press

red button and squeeze spray gun trigger to release

retained high water pressure.

WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting in serious

injury and possible amputation.

• NEVER repair high pressure hose. Replace it.

• Replacement hose rating MUST equal or exceed maximum

pressure rating of unit.

WARNING Risk of eye injury.

Spray could splash back or propel objects

resulting in serious injury.

• Always wear indirect vented (chemical splash) safety goggles

marked to comply with ANSI Z87.1 when using or in vicinity of

this equipment.

• NEVER substitute safety glasses or dry-condition goggles for

indirect vented safety goggles.

WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting in serious

injury and possible amputation.

Spray gun traps high water pressure, even when engine is

stopped and water is disconnected, which could result in

serious injury.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction, press red button

and squeeze spray gun trigger to release high pressure, every

time you stop engine.

16 www.diamondpowerproducts.com

3. Remove detergent siphoning hose from barbed fitting

on pump.

4. Using a firm, blunt object 7/64” in diameter or smaller,

by at least 1” long, such as an Allen wrench, slowly

insert the object into the barbed fitting until you meet

resistance. This resistance is the check ball.

5. Slowly push down until you feel the ball move slightly,

push no more than 1/8”. Slight pressure may be

required to free the ball.

6. Repeat steps 4 and 5 if necessary.

7. Reinstall detergent siphoning hose onto barb fitting.

8. Treat with PumpSaver as described in Protecting the

Pump during storage to prevent reoccurrence.

Check Spray Gun

Examine the hose connection to the spray gun and make

sure it is secure. Test the trigger by pressing the red button

and making sure the trigger “springs back” into place

when you release it. You should not be able to press the

trigger without pressing the red button. Replace spray gun

immediately if it fails any of these tests.

Spray Tip Maintenance

A pulsing sensation felt while squeezing the spray gun

trigger may be caused by excessive pump pressure. The

principal cause of excessive pump pressure is a spray tip

clogged or restricted with foreign materials, such as dirt,

etc. To correct the problem, immediately clean the spray tip

following these instructions:

1. Shut off engine and turn off water supply.

2. ALWAYS point spray gun in a safe direction, press

red button and squeeze spray gun trigger to release

retained high water pressure.

3. Remove spray tip from end of nozzle extension.

4. Use a small paper clip to free any foreign material

clogging or restricting spray tip (A).

5. Remove nozzle extension from spray gun.

6. Using a garden hose, remove additional debris by back

flushing water through nozzle extension. Back flush

between 30to 60 seconds.

7. Reinstall spray tip into nozzle extension.

8. Reconnect nozzle extension to spray gun.

9. Make sure garden hose is connected to water inlet.

Check that high pressure hose is connected to spray

gun and pump. Turn on water.

10. Start engine following instructions How to Start Your

Pressure Washer.

11. Test pressure washer by operating with each quick

connect spray tip.

O-Ring Maintenance

Purchase an O-Ring/Maintenance Kit, part number 705001

by contacting the nearest authorized service center. It is

not included with the pressure washer. This kit includes

replacement o-rings, rubber washer and water inlet filter.

Refer to the instruction sheet provided in the kit to service

your unit’s o-rings.

WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting in serious

injury and possible amputation.

• NEVER repair leaking connections with sealant of any kind.

Replace o-ring or seal.

WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting in serious

injury and possible amputation.

Spray gun traps high water pressure, even when engine is

stopped and water is disconnected, which could result in

serious injury.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction, press red button

and squeeze spray gun trigger to release high pressure, every

time you stop engine.

Pump Oil Maintenance

Changing Pump Oil

Change oil after first 50 hours of operation and then every

200hours or 3 months, whichever occurs first.

NOTICE When changing pump oil, use only high quality

nondetergent 30 weight oil. Use no special additives.

Change pump oil as follows:

1. Clean area around brass oil drain plug at bottom of

pump.

2. Remove oil drain plug. Drain oil completely into an

approved container.

3. When oil has completely drained, install oil drain plug

and tighten firmly.

4. Clean area around pump oil dipstick (A). Remove

dipstick and fill pump with recommended oil

(approximately 12 oz.) to “Full” mark on dipstick.

5. Install pump oil dipstick.

6. Wipe up any spilled oil.

Engine Maintenance

See the engine operator’s manual for instructions on how to

properly maintain the engine.

KEEP OUT OF REACH OF CHILDREN. DON’T

POLLUTE. CONSERVE RESOURCES. RETURN

USED OIL TO COLLECTION CENTERS.

Inspect Muffler and Spark Arrester

Inspect the muffler for cracks, corrosion, or other damage.

Remove the spark arrester, if equipped, and inspect

for damage or carbon blockage. If replacement parts

are required, make sure to use only original equipment

replacement parts.

CAUTION Avoid prolonged or repeated skin contact

with used motor oil.

• Used motor oil has been shown to cause skin cancer in certain

laboratory animals.

• Thoroughly wash exposed areas with soap and water.

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage fuel

tank causing a fire, resulting in death or

serious injury.

Contact with muffler area could cause burns resulting in

serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5ft. (1.5 m) of clearance on all sides of pressure

washer including overhead.

• It is a violation of California Public Resource Code, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in Section

4442, maintained in effective working order. Other states or

federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer

to obtain a spark arrester designed for the exhaust system

installed on this engine.

• Replacement parts must be the same and installed in the same

position as the original parts.

18 www.diamondpowerproducts.com

After Each Use

Water should not remain in the unit for long periods of time.

Sediments or minerals can deposit on pump parts and freeze

pump action. Follow these procedures after every use:

1. Shut off engine, turn off water supply, point gun in a

safe direction, press red button and squeeze trigger to

relieve trapped pressure, and let engine cool.

2. Disconnect hose from spray gun and high pressure

outlet on pump. Drain water from hose, gun, and nozzle

extension. Use a rag to wipe off the hose.

3. Empty pump of all pumped liquids by pulling recoil

handle about six times. This should remove most liquid

in pump.

4. Store unit in a clean, dry area.

5. If storing for more than 30 days, see Long Term

Storage on next page.

WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting in serious

injury and possible amputation.

Spray gun traps high water pressure, even when engine is

stopped and water is disconnected, which could result in

serious injury.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction, press red button

and squeeze spray gun trigger to release high pressure, every

time you stop engine.

WARNING Fuel and its vapors are extremely flammable

and explosive which could cause burns,

fire or explosion resulting in death or

serious injury.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers, or other appliances that have pilot light or other ignition

source because they could ignite fuel vapors.

Winter Storage

NOTICE You must protect your unit from freezing

temperatures.

• Failure to do so will permanently damage your pump and render

your unit inoperable.

• Freeze damage is not covered under warranty.

To protect the unit from freezing temperatures:

1. Follow steps 1-3 in the previous section After Each Use.

2. Use pump saver, Model 6039, to treat pump. This

minimizes freeze damage and lubricates pistons and

seals.

3. If pump saver is not available, connect a 3 ft. (1 m)

section of garden hose to water inlet adapter. Pour

RV-antifreeze (antifreeze without alcohol) into hose.

Pull recoil handle twice. Disconnect 3 ft. (1 m) hose.

4. Store unit in a clean, dry area.

Long Term Storage

If you do not plan to use the pressure washer for more than

30 days, you must prepare the engine and pump for long

term storage.

Protect Fuel System

Fuel Additive:

Fuel can become stale when stored over 30 days. Stale fuel

causes acid and gum deposits to form in the fuel system or

on essential carburetor parts. To keep fuel fresh, use Briggs

& Stratton Advanced Formula Fuel Treatment & Stabilizer,

available wherever Briggs & Stratton genuine service parts

are sold.

For engines equipped with a FRESH START® fuel cap,

use Briggs & Stratton FRESH START available in a drip

concentrate cartridge.

There is no need to drain gasoline from the engine if a fuel

stabilizer is added according to instructions. Run the engine

for 2 minutes to circulate the stabilizer throughout the fuel

system before storage.

If gasoline in the engine has not been treated with a fuel

stabilizer, it must be drained into an approved container.

Run the engine until it stops from lack of fuel. The use of a

fuel stabilizer in the storage container is recommended to

maintain freshness.

Storing the Engine

See the engine operator’s manual for instructions on how to

properly prepare the engine for storage.

Protecting the Pump

To protect the pump from damage caused by mineral

deposits or freezing, use PumpSaver, Model 6039, to treat

pump. This prevents freeze damage and lubricates pistons

and seals.

NOTICE You must protect your unit from freezing

temperatures.

• Failure to do so will permanently damage your pump and render

your unit inoperable.

• Freeze damage is not covered under warranty.

NOTICE PumpSaver is available as an optional accessory. It

is not included with the pressure washer. Contact the nearest

authorized service center to purchase PumpSaver.

To use PumpSaver, make sure the pressure washer is

turned off and disconnected from supply water. Read and

follow all instructions and warnings given on the PumpSaver

container.

Other Storage Tips

1. DO NOT store fuel from one season to another unless it

has been treated as described in Protect Fuel System.

2. Replace fuel container if it starts to rust. Rust and/

or dirt in fuel can cause problems if it’s used with this

unit.

3. Cover unit with a suitable protective cover that does not

retain moisture.

4. Store unit in a clean and dry area.

WARNING Storage covers could cause a fire

resulting in death or serious injury.

• DO NOT place a storage cover over a hot pressure washer.

• Let equipment cool for a sufficient time before placing the cover

on the equipment.

20 www.diamondpowerproducts.com

Troubleshooting

Problem Cause Correction

Pump has following problems: failure

to produce pressure, erratic pressure,

chattering, loss of pressure, low water

volume.

1. Low pressure nozzle installed.

2. Water inlet is blocked.

3. Inadequate water supply.

4. Inlet hose is kinked or leaking.

5. Clogged inlet hose screen.

6. Water supply is over 100°F (38°C).

7. High pressure hose is blocked or

leaks.

8. Spray gun leaks.

9. Nozzle is obstructed.

10. Pump is faulty.

1. Replace with high pressure nozzle.

2. Clear inlet.

3. Provide adequate water flow.

4. Straighten inlet hose, patch leak.

5. Check and clean inlet hose screen.

6. Provide cooler water supply.

7. Clear blocks in outlet hose.

8. Replace spray gun.

9. Clean nozzle.

10. Contact local service facility.

Detergent fails to mix with spray.

1. Detergent siphoning tube is not

submerged.

2. Detergent siphoning tube/filter is

clogged or cracked.

3. High pressure nozzle installed.

4. Check ball stuck in detergent

siphoning system.

1. Insert detergent siphoning tube into

detergent.

2. Clean or replace filter/detergent

siphoning tube.

3. Replace with low pressure nozzle.

4. Unstick check ball as described in

Detergent Siphoning Check Ball.

Engine runs good at no-load but “bogs”

when load is added.

Engine speed is too slow.

Move throttle control to FAST position.

If engine still “bogs down”, contact local

service facility.

Engine will not start; shuts down during

operation or starts and runs rough.

1. Low oil level.

2. Dirty air cleaner.

3. Out of fuel.

4. Stale fuel.

5. Spark plug wire not connected to

spark plug.

6. Bad spark plug.

7. Water in fuel.

8. Excessively rich fuel mixture.

1. Fill crankcase to proper level.

2. Clean or replace air cleaner.

3. Fill fuel tank.

4. Drain fuel tank; fill with fresh fuel.

5. Connect wire to spark plug.

6. Replace spark plug.

7. Drain fuel tank; fill with fresh fuel.

8. Contact local service facility.

Engine lacks power. Dirty air filter. Replace air filter.

La page charge ...

Simplicity 020583-00 Manuel utilisateur

Marque: Simplicity

Modèle: 020583-00

Catégorie: Nettoyeurs haute pression

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Simplicity 020583-00 User manual

Simplicity 020583-00 Manuel utilisateur

Simplicity 020583-00 Manuel utilisateur

dans d''autres langues

Documents connexes