Simplicity 020778-00 Manuel utilisateur
- Catégorie
- Pulvérisateur de peinture
- Taper
- Manuel utilisateur
Ce manuel convient également à
Not for
Reproduction
Manual No. 80089920 Rev -
Pressure Washer
Operator’s Manual
Model Number _____________________________
Revision __________________________________
Serial Number ______________________________
Date Purchased ____________________________
Copyright © 2019. Briggs & Stratton Corporation
Milwaukee, WI, USA. All rights reserved.
DIAMOND™ is a trademark of Briggs & Stratton Corporation.
(800) 743-4115
www.diamondpowerproducts.com
Not for
Reproduction
2 www.diamondpowerproducts.com
Table of Contents
Symbols and Meanings ...........................2
Equipment Description............................3
Features and Controls ............................4
Operation.......................................6
Maintenance ...................................11
Storage .......................................14
Troubleshooting ................................15
Warranty ......................................16
Register Your Product
To ensure prompt and complete warranty coverage, register
your product online at www.onlineproductregistration.com.
Symbols and Meanings
Signal Meaning
DANGER
Indicates a hazard which, if not avoided,
will result in death or serious injury.
WARNING
Indicates a hazard which, if not avoided,
could result in death or serious injury.
CAUTION
Indicates a hazard which, if not avoided,
could result in minor or moderate injury.
NOTICE
Indicates information considered
important, but not hazard-related.
Symbol Name Explanation
Safety Alert
Symbol
Indicates a potential personal
injury hazard.
Read
Operator’s
Manual
Failure to follow warnings,
instructions and operator’s
manual could result in death or
serious injury.
Toxic
Fumes
Engine exhaust contains carbon
monoxide, a poisonous gas that
could kill you in minutes. You
cannot smell it or see it.
Fire
Fuel and its vapors are
extremely ammable which
could cause burns or re
resulting in death or serious
injury.
Engine exhaust could cause
re resulting in death or serious
injury.
Symbol Name Explanation
Fluid
Injection
High-pressure water could cut
through skin resulting in serious
injury and possible amputation.
Spray,
Flying
Objects
Risk of eye injury. Spray could
splash back or propel objects
resulting in serious injury.
Hot Surface
Contact with muer area could
cause burns resulting in serious
injury.
Electric
Shock
Contact with power source
could cause electrical shock
resulting in death or serious
injury.
Kickback
Recoil starter kickback will pull
hand and arm toward engine
faster than you can let go which
could cause broken bones,
sprains or bruises resulting in
serious injury.
Chemical
Burn
Chemicals could cause burns
resulting in death or serious
injury.
Slippery
Surface/Fall
Slippery wet surfaces could
cause you to fall resulting in
death or serious injury.
Fall
Kickback from spray gun could
cause you to fall resulting in
death or serious injury.
WARNING! This product can expose you to
chemicals including gasoline engine exhaust,
which is known to the State of California to cause
cancer, and carbon monoxide, which is known to the State of
California to cause birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov.
WARNING! This product contains lead and lead
compounds, known to the state of California to
cause birth defects or other reproductive harm.
Wash your hands after handling this product. Cancer and
Reproductive Harm - www.P65Warnings.ca.gov.
Not for
Reproduction
3
High Pressure Hose — Connect one end to water pump
and the other end to spray gun.
High Pressure Outlet — Connection for high pressure
hose.
Identication Label — Provides model and serial number of
pressure washer.
Pump — Stainless steel piston, axial cam pump that
develops high pressure.
Water Inlet — Connection for garden hose.
Equipment Description
Read this manual carefully and become familiar
with your product. Know its applications, its
limitations, and any hazards involved. Save these
original instructions for future reference.
To aid in outdoor cleaning projects, this engine-driven,
high-pressure cleaning machine uses a variety of spray
tips and detergent.
Know how to stop the product and reduce pressure
quickly. Keep operating area clear and do not allow
children to operate pressure washer.
Stay alert—watch what you are doing. Do not operate
pressure washer when fatigued or under the inuence of
alcohol or drugs.
Every eort has been made to ensure that information in
this manual is accurate and current. However, we reserve
the right to change, alter, or otherwise improve the product
and this document at any time without prior notice.
NOTICE If you have questions about intended use,
contact an authorized service dealer. This equipment is
designed to be used with Briggs & Stratton
®
authorized
parts only.
For engine related questions, call American Honda
Motor Company, Inc. at (800) 426-7701 or visit
www.honda-engines.com for a dealer locator.
This spark ignition system complies with the Canadian
Standard CAN ICES-2/NMB-2.
High Pressure Outlet
Water Inlet
High Pressure Hose
Identication Label
Pump
Not for
Reproduction
4 www.diamondpowerproducts.com
Features and Controls
Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls and
product warnings.
Not for
Reproduction
5
Accessory Tray — Provides convenient storage
for accessories.
Automatic Cool Down System — Prevents
internal pump damage by discharging warm
water to the ground.
Detergent Siphon Tube — Use to siphon
pressure washer safe detergent into the low
pressure stream.
Spray Wand — Allows you to switch between
spray tips.
Spray Gun — Controls spray using trigger.
Includes trigger lock.
Spray Tips — Multiple patterns for various
cleaning applications.
Spray Tips
Spray Wand
Spray Gun
Automatic Cool Down
System (on pump)
Detergent Siphon Tube
Accessory Tray
Not for
Reproduction
6 www.diamondpowerproducts.com
Operation
Step 1: Safe Location
Before starting the pressure washer, there are two equally
important safety concerns regarding carbon monoxide
poisoning and re that must be addressed.
Operation Location to Reduce the Risk of Carbon
Monoxide Poisoning
The engine exhaust of all fossil fuel burning equipment,
such as a pressure washer, contains carbon monoxide, a
poisonous gas that could kill you in minutes. You cannot
smell it, see it, or taste it. Even if you do not smell exhaust
fumes, you could still be exposed to carbon monoxide gas.
By law, it is required in many states to have a carbon
monoxide alarm in operating condition in your home. A
carbon monoxide alarm is an electronic device that detects
hazardous levels of carbon monoxide. When there is
a buildup of carbon monoxide, the alarm will alert the
occupants by ashing a visual indicator light and an alarm.
Smoke alarms cannot detect carbon monoxide gas.
WARNING! Engine exhaust contains carbon
monoxide, a poisonous gas that could kill you in
minutes. You cannot smell it, see it, or taste it.
Even if you do not smell exhaust fumes, you could still be
exposed to carbon monoxide gas.
• Operate this product only outdoors, far away from
windows, doors and vents to reduce the risk of carbon
monoxide gas accumulating and the potential of being
drawn towards occupied spaces.
• Install battery-operated carbon monoxide alarms or
plug-in carbon monoxide alarms with battery back-up
according to the manufacturer’s instructions. Smoke
alarms cannot detect carbon monoxide gas.
• Do not run this product inside homes, garages,
basements, crawlspaces, sheds, or other partially-
enclosed spaces even if using fans or opening doors and
windows for ventilation. Carbon monoxide can quickly
build up in these spaces and can linger for hours, even
after this product has shut o.
• Point exhaust away from all homes and occupied
spaces.
• If you start to feel sick, dizzy, or weak while using this
product, get to fresh air right away. See a doctor. You
may have carbon monoxide poisoning.
Carbon monoxide alarm
Not for
Reproduction
7
Operation Location to Reduce the Risk of Fire
WARNING! Exhaust heat/gases could ignite
combustibles, structures or damage fuel tank
causing a re, resulting in death or serious injury.
• Pressure washer must be at least 5 ft. (1.5 m) from any
structure, overhang, trees, windows, doors, and any wall
opening, shrubs, or vegetation over 12 in. (30.5 cm) in
height.
• Do not place pressure washer under a deck or other type
of structure that may conne airow. Smoke alarm(s)
must be installed and maintained indoors according to
the manufacturer’s instructions /recommendations.
• Carbon monoxide alarms cannot detect smoke.
• It is a violation of California Public Resource Code
Section 4442, to use or operate the engine on any forest-
covered, brush-covered, or grass-covered land unless
the exhaust system is equipped with a spark arrester, as
dened in Section 4442, maintained in eective working
order. Other states or federal jurisdictions may have
similar laws, reference Federal Regulation 36 CFR Part
261.52.
• Contact the original equipment manufacturer, retailer,
or dealer to obtain a spark arrester designed for the
exhaust system installed on this engine.
• Replacement parts must be the same and installed in the
same position as the original parts.
Step 2: Oil and Fuel
Check Oil Level
1. Make sure pressure washer is on a level surface.
2. Refer to engine operator’s manual and follow oil and
fuel recommendations and instructions.
Transporting
Do not tip engine or equipment at an angle which causes
fuel to spill.
Step 3: Set Up
Clean Debris
Clean any accumulated debris. Keep area around muer
free from any debris.
• Use a soft bristle brush to loosen caked on dirt or oil.
• Use a damp cloth to wipe exterior surfaces clean.
Lubricate O-rings
Lubricate all connections shown to extend the life of the
o-rings.
1. Inspect and clean connecting surfaces prior to
lubrication and assembly. Replace o-rings that are
damaged or missing. See Common Service Parts.
NOTICE Never repair leaking connections with sealant of
any kind. Replace o-ring.
2. Use a small brush or cotton swab to apply a light
coating of grease directly to o-rings.
Check / Connect Gun and Hose
1. If spray gun trigger depresses without pressing
trigger lock or if spray gun remains depressed when
released, replace spray gun immediately.
2. If high pressure hose is damaged, exposing inner
mesh, replace immediately.
MUFFLER
5 ft (1.5 m)
min.
5 ft (1.5 m) min.
Spray Gun
High
Pressure
Hose
Spray Wand
Trigger Lock
Not for
Reproduction
8 www.diamondpowerproducts.com
3. Attach high pressure hose to spray gun and high
pressure outlet on pump. Tighten by hand.
WARNING! The high pressure uid could cut
through skin and its underlying tissues, resulting
in serious injury and possible amputation. Never
attach spray wand directly to high pressure hose.
Check Water Inlet Screen / Connect Garden Hose
1. Inspect inlet screen. Remove debris or replace if
damaged.
2. Run water through garden hose (not to exceed 50 ft
(15 m) to clean out debris, then connect to water inlet.
NOTICE There must be at least 10 ft (3 m) of
unrestricted garden hose between the pressure washer
inlet and any device, such as a vacuum breaker, to
prevent pump damage.
3. Turn on water, point spray gun in safe direction, press
trigger lock and depress trigger to purge pump system
of air.
4. Attach spray wand to spray gun. Tighten by hand.
Step 4: Spray Tips
1. Select desired spray tip:
Low Pressure
Black Soap
Use to apply
detergent
Delicate Rinse
White, 40°
Cars / Vans
/ Trucks /
Outdoor
Furniture
General Rinse
Yellow, 15°
Siding /
Patios Decks
Driveways /
Garage Floors
Maximum
Rinse
Red, 0°
Paint Removal
/ Oil Stains
/ Rust Removal
2. Pull spray wand quick connect collar back, insert
spray tip and release. Tug spray tip to ensure it is
secure.
Step 5: Start Up
NOTICE Do not start engine without water supply
connected and turned on.
1. Level product before starting.
WARNING! Risk of eye injury. Spray could
splash back or propel objects, resulting in
serious injury.
• Always wear indirect vented (chemical splash) safety
goggles when using or near this product. (Safety glasses
do not provide full protection).
• Always wear protective clothing such as long-sleeved
shirts, long pants and closed-toed shoes.
WARNING! Recoil starter kickback (rapid
retraction) will pull hand and arm toward engine
faster than you can let go, which could cause
broken bones, fractures, bruises, or sprains and result in
serious injury.
Inlet Screen
Not for
Reproduction
9
2. Position yourself as shown below, and start engine
according to instructions given in engine operator’s
manual.
WARNING! High-pressure water could cut
through skin resulting in serious injury and
possible amputation.
• Do not direct discharge at self or others.
• Call physician immediately if cut by uid. Do not treat as
a simple cut.
• Do not touch spray tips while spraying.
WARNING! Use of pressure washer
could create slippery surfaces causing
you to fall, resulting in death or serious
injury. Kickback from spray gun could cause you to fall
resulting in death or serious injury. Operate pressure
washer from a stable surface.
3. Firmly grasp spray gun with both hands, point spray
gun in safe direction, press trigger lock and depress
trigger to begin spraying.
4. Apply high pressure spray to a small area rst, then
check the surface for damage. If no damage is found,
it is okay to continue cleaning.
WARNING! Risk of electrocution. Contact with
power source could cause electric shock or burn
resulting in death or serious injury. Never spray
near power source.
Usage Tips
• For most eective cleaning, keep spray tip 8 to 24 in (20
to 61 cm) away from cleaning surface.
• Do not use high pressure spray tips closer than 6 in (15
cm) to prevent damage to the cleaning surface.
• Start at the top of the area to be rinsed, working down
with long, even, overlapping strokes.
Step 6: Applying Detergent
WARNING! Chemicals could cause burns
resulting in death or serious injury.
• Follow chemical manufacturer’s label instructions for
proper use and handling of the chemical.
• Only use products marketed for use with pressure
washers.
• Never spray acids or ammable liquids.
Check Detergent Siphoning Tube
Clean detergent tube if clogged or replace if leaking.
To apply detergent, follow these steps:
1. Attach detergent siphon tube to the barbed fitting on
the pump.
2. Prepare detergent per pressure washer detergent
manufacturer’s instructions.
3. Insert detergent siphon tube into pressure washer
detergent.
4. Install black detergent spray tip. See Spray Tips.
5. Apply per manufacturer’s instructions.
NOTICE Detergent cannot be applied with the high
pressure spray tips (White, Yellow or Red).
Not for
Reproduction
10 www.diamondpowerproducts.com
Step 7: Shut Down
1. Release spray gun trigger and let engine idle for one
minute.
2. Turn engine o according to instructions given in
engine operator’s manual.
WARNING! Spray gun traps high water
pressure, even after engine shut down and water
disconnection, which could result in serious
injury.
3. Point spray gun in safe direction. Press trigger lock
and depress trigger to relieve high water pressure.
Step 8: Clean Up
1. Turn o water and purge system.
2. Disconnect and drain all hoses, spray gun and spray
wand.
3. Empty pump of all liquids by pulling recoil handle
about six times.
NOTICE If storing in freezing temperatures or more than
30 days, see Storage.
Maintenance
Maintenance Schedule
Follow the hourly or calendar intervals, whichever occurs
rst. See the engine operator’s manual for instructions on
how to properly maintain the engine.
General Recommendations
Regular maintenance will improve the performance and
extend the life of the pressure washer. See any authorized
dealer for service.
Pump Oil
Do not attempt any oil maintenance on this pump. The pump
is pre-lubricated and sealed from the factory, requiring no
additional maintenance for the life of the pump.
Detergent Siphoning Check Ball
The check ball in detergent siphoning system may become
stuck from dried soap or minerals in water. The check ball
can be freed by performing the following:
WARNING! Chemical Burn Hazard. Chemicals
could cause burns resulting in death or serious
injury. Follow chemical manufacturer’s label
instructions for proper use and handling of the chemical.
Following Shut Down, remove detergent siphoning hose
from barbed tting on pump.
1. Insert paper clip, or similar device, into barbed tting
on pump and push down until ball moves.
2. Reinstall detergent siphoning hose.
Spray Tip Maintenance
Clean an obstructed spray tip to correct a pulsing
sensation when squeezing the spray gun trigger.
1. Following Shut Down, remove spray tip from spray
wand.
2. Use a paper clip, or similar device, to free foreign
material.
Engine Maintenance
See the engine operator’s manual for instructions on how
to properly maintain the engine.
Common Service Parts
Pump Saver™ ............................6039
O-ring Maintenance Kit ...................705001
Water Inlet Screen ..................... B2384GS
Engine Oil Bottle ...............100005 or 100028
Contact an authorized service dealer or
powerboss-equipment.com for a full list of parts and
diagrams.
Every 8 Hours or Daily (see Operation Section)
Check engine oil level
Clean debris
Lubricate o-rings
Check spray gun
Check high pressure hose
Check / clean water inlet screen
Check detergent siphoning tube
Not for
Reproduction
11
Storage
WARNING! Fuel and its vapors are extremely
ammable, which could cause burns or re,
resulting in death or serious injury. Do not store
fuel near ignition source.
1. Place detergent siphon tube in water and ush
detergent from system by running pressure washer
with black spray tip.
Protecting Fuel System
2. Treat or drain fuel from pressure washer as fuel can
become stale when stored over 30 days.
Each time you ll the container with fuel, add STA-BIL
360°® PROTECTION™ to the fuel as specied by the
manufacturer’s instructions. This keeps fuel fresh and
decreases fuel-related problems or contamination in the
fuel system.
It is not necessary to drain fuel from the engine when STA-
BIL 360°® PROTECTION™ is added as instructed. Before
storage, turn the engine ON for 2 minutes to move the fuel
and stabilizer through the fuel system.
If fuel in the engine has not been treated with STA-
BIL 360°® PROTECTION™, it must be drained into an
approved container. Then run the engine until it stops from
lack of fuel.
Engine Maintenance
See the engine operator’s manual for instructions on how
to properly maintain the engine.
Protecting the Pressure Washer
3. Turn o water and purge system.
4. Disconnect and drain all hoses, spray gun and spray
wand.
5. Empty pump of all liquids by pulling recoil handle
about six times.
NOTICE Store spray gun indoors and keep from freezing.
Protecting the Pump
6. Treat pump with Pump Saver.
Use Pump Saver to protect pump from damage caused by
mineral deposits and freezing. It also lubricates pistons and
seals. See Common Service Parts.
Read and follow all Pump Saver warnings and instructions.
If Pump Saver is not available, connect a 3 ft. (1 m)
section of garden hose to water inlet. Pour RV-antifreeze
(antifreeze without alcohol) into hose. Pull recoil handle
twice. Disconnect hose.
NOTICE You must protect your product from freezing
temperatures. Failure to do so will permanently damage
your pump and spray gun rendering your product
inoperable.
7. Store unit in a clean and dry area.
WARNING! Storage covers could cause a re
resulting in death or serious injury. Do not place
a storage cover over a hot pressure washer. Let
product cool before installing cover.
Not for
Reproduction
12 www.diamondpowerproducts.com
Troubleshooting
Problem Cause Correction
Pump has following
problems: failure to
produce pressure, loss
of pressure, low water
volume.
1. Low pressure spray tip installed.
2. Inadequate water supply.
3. Clogged inlet hose screen.
4. Spray tip is obstructed.
5. Connections leak.
6. High pressure hose or spray gun leaks.
1. Replace with high pressure spray tip.
2. Provide adequate water ow.
3. Check and clean inlet hose screen.
4. Clean spray tip. See Spray Tip
Maintenance.
5. Tighten connections or replace o-rings.
6. Replace.
Detergent fails to mix
with spray.
1. High pressure spray tip installed.
2. Check ball stuck in detergent
siphoning system.
3. Detergent siphoning tube is clogged or
cracked.
1. Replace with low pressure black spray tip.
2. Free check ball. See Detergent Siphoning
Check Ball.
3. Clean or replace detergent siphoning
tube.
Engine will not start;
starts and runs rough
or shuts down during
operation.
1. Out of fuel.
2. Flooded with fuel.
3. Dirty air lter.
4. Spark plug wire not connected to spark
plug.
1. Fill fuel tank.
2. Wait 5 minutes before starting.
3. Clean or replace air lter.
4. Connect wire to spark plug.
For all other issues, see an Briggs & Stratton authorized dealer.
*This pressure washer is rated in accordance to the Pressure Washer Manufacturers’ Association (PWMA) standard PW101-2010
(Testing and Rating Performance of Pressure Washers).
Specications
White, 40
°
....................................2100 PSI (145 bar) @ 2.3 GPM (8.7 L/min)*
Yellow, 15
°
...................................2500 PSI (172 bar) @ 2.2 GPM (8.3 L/min)*
Red, 0
°
......................................3000 PSI (207 bar) @ 2.0 GPM (7.6 L/min)*
Water Supply Temperature .....................................41°F (5°C) - 100°F (38°C)
min Water Supply Flow Rate ...................................... 3.3 GPM (12.5 L/min)
min Water Supply Pressure ...........................................20 PSI (1.38 bar)
Not for
Reproduction
13
Not for
Reproduction
14 www.diamondpowerproducts.com
80082391_EN Rev -
BRIGGS & STRATTON WARRANTY POLICY
LIMITED WARRANTY
Briggs & Stratton warrants that, during the warranty period specied below, it will repair or replace, free of charge, any part that is defective in material or workmanship
or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is eective for
and is subject to the time periods and conditions stated below. For warranty service, nd the nearest Authorized Service Dealer in our dealer locator map at
BRIGGSANDSTRATTON.COM. The purchaser must contact the Authorized Service Dealer, and then make the product available to the Authorized Service Dealer for
inspection and testing.
There is no other express warranty. Implied warranties, including those of merchantability and tness for a particular purpose, are limited to the
warranty period listed below, or to the extent permitted by law. Liability for incidental or consequential damages are excluded to the extent exclusion
is permitted by law. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specic legal rights and you
may also have other rights which vary from state to state or country to country.**
WARRANTY PERIOD
* Applies to Briggs & Stratton engines only. Warranty coverage of non-Briggs & Stratton engines is provided by that engine manufacturer. Emissions-related components
are covered by the Emissions Warranty Statement.
** In Australia - Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be
of acceptable quality and the failure does not amount to a major failure. For warranty service, nd the nearest Authorized Service Dealer in our dealer locator map at
BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or writing to [email protected], Briggs & Stratton Australia Pty Ltd, 1
Moorebank Avenue, NSW, Australia, 2170.
The warranty period begins on the date of purchase by the rst retail or commercial consumer. “Consumer use” means personal residential household use by a retail
consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once a product has experienced commercial
use, it shall thereafter be considered as a commercial use product for purposes of this warranty.
Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the
product will be used to determine the warranty period. Product registration is not required to obtain warranty service on Briggs & Stratton products.
ABOUT YOUR WARRANTY
Warranty service is available only through Briggs & Stratton Authorized Service Dealers. This warranty covers only defects in materials or workmanship. It does not cover
damage caused by improper use or abuse, improper maintenance or repair, normal wear and tear, or stale or unapproved fuel.
Improper Use and Abuse - The proper, intended use of this product is described in the Operator’s Manual. Using the product in a way not described in the Operator’s
Manual or using the product after it has been damaged will not be covered under this warranty. Warranty coverage will also not be provided if the serial number on the
product has been removed or the product has been altered or modied in any way, or if the product has evidence of abuse such as impact damage or water/chemical
corrosion damage.
Improper Maintenance or Repair - This product must be maintained according to the procedures and schedules provided in the Operator’s Manual, and serviced or
repaired using genuine Briggs & Stratton parts or equivalent. Damage caused by lack of maintenance or use of non-original parts is not covered by warranty.
Normal Wear and Tear - Like most mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not cover repairs when normal
use has exhausted the life of a part or the equipment. Maintenance and wear items such as lters, belts, cutting blades, and brake pads (except engine brake pads) are
not covered by warranty due to wear characteristics alone, unless the cause is due to defects in material or workmanship.
Stale or Unapproved Fuel - In order to function correctly, this product requires fresh fuel that conforms to the criteria specied in the Operator’s Manual. Engine or
equipment damage caused by stale fuel or the use of unapproved fuels (such as E15 or E85 ethanol blends) is not covered by warranty.
Other Exclusions - This warranty excludes damage due to accident, abuse, modications, alterations, improper servicing, freezing or chemical deterioration.
Attachments or accessories that were not originally packaged with the product are also excluded. There is no warranty coverage on equipment used for primary power in
place of utility power or on equipment used in life support applications. This warranty does not include used, reconditioned, second-hand, or demonstration equipment or
engines. This warranty also excludes failures due to acts of God and other force majeure events beyond the manufacturer’s control.
Item Consumer Use Commercial Use
Equipment 24 months 3 months
Engine* 24 months 3 months
Frame 36 months 3 months
Not for
Reproduction
Laveuse à pression
Manuel d’utilisation
Référence du modèle ________________________
Révision __________________________________
Numéro de série ____________________________
Date d’achat : ______________________________
Droit d'auteur © 2019. Briggs & Stratton Corporation
Milwaukee, WI, É.-U. Tous droits réservés.
DIAMOND™ est une déposées de Briggs & Stratton Corporation
(800) 743-4115
www.diamondpowerproducts.com
Not for
Reproduction
2 www.diamondpowerproducts.com
Table des matières
Symboles et signications .........................2
Description de l’équipement .......................3
Caractéristiques et commandes ....................4
Utilisation.......................................6
Entretien ......................................12
Entreposage ...................................15
Dépannage ....................................16
Garantie.......................................18
Enregistrer votre produit
Pour assurer une couverture rapide et complète de la
garantie, veuillez inscrire votre produit en ligne à l’adresse
www.onlineproductregistration.com.
Symboles et signications
Signal Signication
DANGER
Indique un danger qui, si non évité,
causera la mort ou des blessures
graves.
AVERTISSEMENT
Indique un danger qui, si non évité,
pourrait causer la mort ou des
blessures graves.
ATTENTION
Indique un danger qui, si non évité,
pourrait causer des blessures
mineures ou modérées.
AVIS
Indique des informations
considérées importantes, mais non
liées aux dangers.
Symbole Nom Explication
Symbole
d’alerte de
sécurité
Le symbole d’alerte de sécurité
indique un risque de blessure
corporelle.
Veuillez lire
le manuel
d’utilisation
Ne pas respecter les
avertissements, les instructions et le
manuel de l’utilisateur peut entraîner
des blessures graves ou la mort.
Vapeurs
toxiques
Les gaz d’échappement du moteur
contiennent du monoxyde de
carbone, un gaz toxique pouvant
provoquer la mort en quelques
minutes. Vous ne pouvez ni le sentir
ni le voir.
Incendie
Le carburant et ses vapeurs sont
extrêmement inammables et
pourraient causer des brûlures ou
un incendie entraînant la mort ou
des blessures graves.
L’échappement du moteur peut
provoquer un incendie pouvant
entraîner la mort ou de graves
blessures.
Symbole Nom Explication
Injection
de liquide
De l’eau à haute pression peut
couper la peau, causer des
blessures graves et possiblement,
une amputation.
Aérosol,
objets
volants
Risque de blessure aux yeux. Le
jet d’eau peut rejaillir ou propulser
des objets en entraînant de graves
lésions.
Surface
chaude
Tout contact avec la zone du
silencieux peut causer des
brûlures risquant de provoquer des
blessures graves.
Décharge
électrique
Le contact avec la source
d’alimentation électrique pourrait
provoquer une décharge électrique
entraînant la mort ou de graves
lésions.
Recul
Le recul du lanceur a pour eet de
tirer la main et le bras en direction
du moteur plus rapidement qu’il n’est
possible de le lâcher, ce qui pourrait
provoquer des fractures osseuses,
des entorses ou des ecchymoses
entraînant de graves lésions.
Brûlure
chimique
Les produits chimiques peuvent
causer des brûlures risquant
d’entraîner la mort ou des blessures
graves.
Surface
glissante
ou chute
Les surfaces mouillées et
glissantes peuvent vous faire
tomber et causer la mort ou des
blessures graves.
Chute
Le recul du pistolet de pulvérisation
pourrait vous faire tomber et
entraîner la mort ou de graves
lésions.
AVERTISSEMENT! Ce produit peut vous
exposer à des agents chimiques, y compris les
échappements des moteurs à essence, connus
dans l’État de la Californie pour causer le cancer, ainsi
que le monoxyde de carbone, connu dans l’État de la
Californie pour causer des malformations congénitales ou
les dommages à l’appareil reproducteur. Pour obtenir de
plus amples renseignements, visitez le
www.P65Warnings.ca.gov.
AVERTISSEMENT! Ce produit contient du
plomb et des composés de plomb, connus dans
l’État de la Californie pour causer des
malformations congénitales ou les dommages à l’appareil
reproducteur. Nettoyez-vous les mains après la
manipulation de ce produit. Cancer et eets nocifs sur la
reproduction – www.P65Warnings.ca.gov
Not for
Reproduction
3
Description de l’équipement
Veuillez bien lire ce manuel et vous familiariser
avec votre produit. Prenez connaissance de ses
applications, ses limitations, et tous les risques
impliqués. Conservez ces instructions d’origine pour vous
y reporter dans le futur.
Pour vous aider dans vos projets de nettoyage extérieur,
cette machine de nettoyage motorisée à haute pression
utilise une gamme d’embouts de pulvérisation et de
détergents.
Apprenez à arrêter le produit et à réduire la pression
rapidement. Maintenez la zone d’utilisation dégagée et ne
laissez pas les enfants utiliser la laveuse à pression.
Soyez vigilant, regardez toujours ce que vous faites.
Ne faites pas fonctionner la laveuse à pression lorsque
vous êtes fatigué(e) ou sous l’inuence de l’alcool ou de
drogues.
Nous nous sommes eorcés de fournir dans ce manuel
des informations exactes et à jour. Toutefois, nous nous
réservons le droit de changer, de modier ou même
d’améliorer le produit et ce document à tout moment sans
préavis de notre part.
AVIS Si vous avez des questions sur l’usage prévu,
contactez un centre de service autorisé. Cet équipement
est conçu pour être utilisé avec les pièces Briggs &
Stratton
®
approuvées uniquement.
Pour toutes questions relatives au moteur, veuillez
communiquer avec American Honda Motor Company, Inc.
au (800) 426-7701 ou visiter www.honda-engines.com
pour trouver un distributeur de service.
Ce dispositif d’allumage par étincelle est conforme à la
norme canadienne CAN ICES-2/NMB-2.
Boyau haute pression — Raccordez une extrémité
à la pompe à eau et l’autre extrémité au pistolet de
pulvérisation.
Entrée d’eau — Raccord pour le tuyau d’arrosage.
Étiquette d’identication — Indique les numéros de modèle
et de série de la laveuse à pression.
Pompe — Pompe à came axiale avec piston en acier
inoxydable pour produire une pression élevée.
Sortie haute pression — Raccord pour le boyau haute
pression.
Entrée d’eau
Étiquette d’identication
Boyau haute pression
Pompe
Sortie haute pression
Not for
Reproduction
4 www.diamondpowerproducts.com
Caractéristiques et commandes
Comparez les illustrations avec votre laveuse à pression pour vous familiariser avec l’emplacement des diverses
commandes et les avertissements du produit.
Not for
Reproduction
5
Embouts de pulvérisation — Formes de
jet multiples pour diverses applications de
nettoyage.
Lance de pulvérisation — Vous permet
d’interchanger les embouts de pulvérisation.
Pistolet de pulvérisation — Commande la
pulvérisation en utilisant la gâchette. Comprend
le verrou de la gâchette.
Plateau à accessoires — Rangement pratique
pour les accessoires.
Système automatique de refroidissement —
Prévient les dommages internes à la pompe en
déversant l’eau chaude sur le sol.
Tube de siphonnement du détergent — Utilisez
pour siphonner les détergents sans risque
d’endommagement pour le nettoyeur à haute
pression dans le jet à basse pression.
Embouts de pulvérisation
Lance de pulvérisation
Pistolet de pulvérisation
Système automatique
de refroidissement
(sur la pompe)
Tube de siphonnement
du détergent
Plateau à accessoires
Not for
Reproduction
6 www.diamondpowerproducts.com
Utilisation
Étape 1 : Emplacement sécuritaire
Avant de démarrer la laveuse à pression, il y a deux
principes de sécurité également importants relatifs à
l’intoxication au monoxyde de carbone et aux incendies qui
doivent être respectés.
Emplacement d’utilisation pour réduire le risque
d’intoxication au monoxyde de carbone
Les gaz d’échappement des moteurs de tous les
équipements fonctionnant avec un carburant fossile,
comme une laveuse à pression, contiennent du monoxyde
de carbone, un gaz toxique qui peut être mortel en
quelques minutes. Il est inodore, invisible et sans saveur.
Même si vous ne sentez pas de vapeurs d’échappement,
vous pourriez quand même être exposé(e) au gaz de
monoxyde de carbone.
La législation de nombreux États rend obligatoire
l’installation d’un détecteur de monoxyde de carbone
en état de marche à votre domicile. Un détecteur de
monoxyde de carbone est un dispositif électronique qui
détecte les niveaux dangereux de monoxyde de carbone.
En cas d’accumulation de monoxyde de carbone, le
détecteur alertera les occupants en faisant clignoter
un voyant lumineux et en déclenchant une alarme. Les
détecteurs de fumée ne détectent pas le monoxyde de
carbone.
AVERTISSEMENT! Les gaz d’échappement du
moteur contiennent du monoxyde de carbone, un
gaz toxique pouvant provoquer la mort en
quelques minutes. Il est inodore, invisible et sans saveur.
Même si vous ne sentez pas de vapeurs d’échappement,
vous pourriez quand même être exposé(e) au gaz de
monoxyde de carbone.
• Utilisez ce produit uniquement à l’extérieur et à l’écart
des fenêtres, portes et évents pour réduire le risque
d’accumulation de monoxyde de carbone et son
éventuelle propagation dans des espaces occupés.
• Installer et assurer l’entretien d’avertisseurs de
monoxyde de carbone fonctionnant à piles ou alimentés
par câble avec batterie de secours selon les directives
du fabricant. Les détecteurs de fumée ne détectent pas
le monoxyde de carbone.
• Ne faites pas fonctionner ce produit à l’intérieur de
maisons, de garages, de sous-sols, de vides sanitaires,
de remises ou autres espaces partiellement clos, même
si des ventilateurs sont utilisés ou que des portes et
des fenêtres sont laissées ouvertes pour la ventilation.
Le monoxyde de carbone peut s’accumuler rapidement
dans ces espaces et peut y rester pendant des heures,
même après l’arrêt du produit.
• Pointez l’échappement loin de tous les espaces occupés
et habitations.
Si vous commencez à vous sentir mal, étourdi(e), ou faible
en utilisant ce produit, sortez au grand air immédiatement.
Voir un médecin. Vous pourriez être intoxiqué(e) par le
monoxyde de carbone.
Alarme de monoxyde
de carbone
UTILISEZ Á L’EXTÉRIEUR: ÉVITEZ L’EMPOISONNEMENT AU
MONOXYDE DE CARBONE
ALARMES DE MONOXYDE DE CARBONE
Installez les alarmes de monoxyde de carbone
àl’intérieur de votre demeure. Sans alarmes
de monoxyde de carbone en état de marche,
vous pourriez ne pas réaliser que vous devenez
malade et en voie de mourir d’empoisonnement
au monoxyde de carbone.
ne pas pointer vers la résidence
SILENCIEUX
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Simplicity 020778-00 Manuel utilisateur
- Catégorie
- Pulvérisateur de peinture
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Simplicity 020778-00 User manual
Documents connexes
-
Simplicity 020773-00 Manuel utilisateur
-
-
-
-
Briggs & Stratton DIAMOND Manuel utilisateur
-
Simplicity 020583-00 Manuel utilisateur
-
Simplicity 020474-02 Manuel utilisateur
-
-
-