Electrolux EGW7353NOX Manuel utilisateur

Marque: Electrolux

Modèle: EGW7353NOX

Taper: Manuel utilisateur

EGW7353

................................................ .............................................

EN HOB USER MANUAL 2

FR TABLE DE CUISSON NOTICE D'UTILISATION 16

CONTENTS

1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2. SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3. PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4. DAILY USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

5. HELPFUL HINTS AND TIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

6. CARE AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

7. TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

9. TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

WE’RE THINKING OF YOU

Thank you for purchasing an Electrolux appliance. You’ve chosen a product that brings with it

decades of professional experience and innovation. Ingenious and stylish, it has been designed

with you in mind. So whenever you use it, you can be safe in the knowledge that you’ll get great

results every time.

Welcome to Electrolux.

Visit our website for:

Get usage advice, brochures, trouble shooter, service information:

www.electrolux.com

www.electrolux.com/productregistration

Buy Accessories, Consumables and Original spare parts for your appliance:

www.electrolux.com/shop

CUSTOMER CARE AND SERVICE

We recommend the use of original spare parts.

When contacting Service, ensure that you have the following data available.

The information can be found on the rating plate. Model, PNC, Serial Number.

Warning / Caution-Safety information

General information and tips

Environmental information

Subject to change without notice.

www.electrolux.com

1. SAFETY INFORMATION

Before the installation and use of the appliance, carefully

read the supplied instructions. The manufacturer is not

responsible if an incorrect installation and use causes in-

juries and damages. Always keep the instructions with

the appliance for future reference.

1.1 Children and vulnerable people safety

WARNING!

Risk of suffocation, injury or permanent disability.

• This appliance can be used by children aged from 8

years and above and persons with reduced physical,

sensory or mental capabilities or lack of experience and

knowledge if they are supervised by an adult or a per-

son who is responsible for their safety.

• Do not let children play with the appliance.

• Keep all packaging away from children.

• Keep children and pets away from the appliance when

it operates or when it cools down. Accessible parts are

hot.

• If the appliance has a child safety device, we recom-

mend that you activate it.

• Cleaning and user maintenance shall not be made by

children without supervision.

1.2 General Safety

• The appliance and its accessible parts become hot

during use. Do not touch the heating elements.

• Do not operate the appliance by means of an external

timer or separate remote-control system.

• Unattended cooking on a hob with fat or oil can be

dangerous and may result in fire.

ENGLISH 3

• Never try to extinguish a fire with water, but switch off

the appliance and then cover flame e.g. with a lid or a

fire blanket.

• Do not store items on the cooking surfaces.

• Do not use a steam cleaner to clean the appliance.

• Metallic objects such as knives, forks, spoons and lids

should not be placed on the hob surface since they

can get hot.

• If the glass ceramic surface is cracked, switch off the

appliance to avoid the possibility of electric shock.

SAFETY INSTRUCTIONS

This appliance is suitable for the following

markets: FR

2.1 Installation

WARNING!

Only a qualified person must in-

stall this appliance.

• Remove all the packaging.

• Do not install or use a damaged appli-

ance.

• Obey the installation instruction sup-

plied with the appliance.

• Keep the minimum distance from the

other appliances and units.

• Always be careful when you move the

appliance because it is heavy. Always

wear safety gloves.

• Seal the cut surfaces with a sealant to

prevent moisture to cause swelling.

• Protect the bottom of the appliance

from steam and moisture.

• Do not install the appliance adjacent to

a door or under a window. This pre-

vents hot cookware to fall from the ap-

pliance when the door or the window is

opened.

• If the appliance is installed above draw-

ers make sure that the space, between

the bottom of the appliance and the up-

per drawer, is sufficient for air circula-

tion.

• The bottom of the appliance can get

hot. We recommend to install a non-

combustile separation panel under the

appliance to prevent access to the bot-

tom.

Electrical connection

WARNING!

Risk of fire and electrical shock.

• All electrical connections must be made

by a qualified electrician.

• The appliance must be earthed.

• Before carrying out any operation make

sure that the appliance is disconnected

from the power supply.

• Use the correct electricity mains cable.

• Do not let the electricity mains cable

tangle.

• Make sure the mains cable or plug (if

applicable) does not touch the hot ap-

pliance or hot cookware, when you

connect the appliance to the near sock-

ets

• Make sure the appliance is installed

correctly. Loose and incorrect electricity

mains cable or plug (if applicable) can

make the terminal become too hot.

• Make sure that a shock protection is in-

stalled.

• Use the strain relief clamp on cable.

www.electrolux.com

• Make sure not to cause damage to the

mains plug (if applicable) or to the

mains cable. Contact the Service or an

electrician to change a damaged mains

cable.

• The electrical installation must have an

isolation device which lets you discon-

nect the appliance from the mains at all

poles. The isolation device must have a

contact opening width of minimum 3

mm.

• Use only correct isolation devices: line

protecting cut-outs, fuses (screw type

fuses removed from the holder), earth

leakage trips and contactors.

Gas connection

• All gas connections should be made by

a qualified person.

• Make sure that there is air circulation

around the appliance.

• The information about the gas supply is

on the rating plate.

• This appliance is not connected to a

device, which evacuates the products

of combustion. Make sure to connect

the appliance according to current in-

stallation regulations. Pay attention to

requirements regarding adequate venti-

lation.

2.2 Use

WARNING!

Risk of injury, burns or electric

shock.

• Use this appliance in a household envi-

ronment.

• Do not change the specification of this

appliance.

• Do not let the appliance stay unatten-

ded during operation.

• Do not operate the appliance with wet

hands or when it has contact with wa-

ter.

• Do not put cutlery or saucepan lids on

the cooking zones. They become hot.

• Set the cooking zone to “off” after use.

• Do not use the appliance as a work

surface or as a storage surface.

• If the surface of the appliance is

cracked, disconnect immediately the

appliance from the power supply. This

to prevent an electrical shock.

WARNING!

Risk of fire or explosion.

• Fats and oil when heated can release

flammable vapours. Keep flames or

heated objects away from fats and oils

when you cook with them.

• The vapours that very hot oil releases

can cause spontaneous combustion.

• Used oil, that can contain food rem-

nants, can cause fire at a lower temper-

ature than oil used for the first time.

• Do not put flammable products or items

that are wet with flammable products

in, near or on the appliance.

WARNING!

Risk of damage to the appliance.

• Do not keep hot cookware on the con-

trol panel.

• Do not let cookware to boil dry.

• Be careful not to let objects or cook-

ware fall on the appliance. The surface

can be damaged.

• Do not activate the cooking zones with

empty cookware or without cookware.

• Do not put aluminium foil on the appli-

ance.

• Cookware made of cast iron, aluminium

or with a damaged bottom can cause

scratches on the glass ceramic. Always

lift these objects up when you have to

move them on the cooking surface.

• Provide good ventilation in the room

where the appliance is installed.

• Make sure that the ventilation openings

are not blocked.

• Use only stable cookware with the cor-

rect shape and diameter larger than the

dimensions of the burners. There is a

risk of overheating and rupture of the

glass plate (if applicable).

• Make sure the flame does not go out

when you quickly turn the knob from

the maximum to the minimum position.

• Make sure pots are centrally positioned

on the rings and do not stick out over

edges of the cooking surface.

• Use only the accessories supplied with

the appliance.

ENGLISH 5

• Do not install a flame diffuser on the

burner.

2.3 Care and Cleaning

WARNING!

Risk of damage to the appliance.

• Clean regularly the appliance to prevent

the deterioration of the surface material.

• Do not use water spray and steam to

clean the appliance.

• Do not clean the burners in the dish-

washer.

• Clean the appliance with a moist soft

cloth. Only use neutral detergents. Do

not use abrasive products, abrasive

cleaning pads, solvents or metal ob-

jects.

2.4 Disposal

WARNING!

Risk of injury or suffocation.

• Contact your municipal authority for in-

formation on how to discard the appli-

ance correctly.

• Disconnect the appliance from the

mains supply.

• Cut off the mains cable and discard it.

• Flat the external gas pipes.

3. PRODUCT DESCRIPTION

3.1 Cooking surface layout

2 3

Triple Crown burner

Semi-rapid burner

Auxiliary burner

Control knobs

3.2 Control knobs

Symbol Description

no gas supply /

off position

ignition position /

maximum gas

supply

Symbol Description

minimum gas

supply

4. DAILY USE

WARNING!

Refer to the Safety chapters.

www.electrolux.com

4.1 Ignition of the burner

WARNING!

Be very careful when you use

open fire in kitchen environment.

Manufacturer decline any respon-

sibility in case misuse of the flame

Always light the burner before you

put cookware.

To light the burner:

Turn the control knob counterclock-

wise to the maximum position (

) and push it down.

Keep the control knob pushed for ap-

proximately 5 seconds; this will let

thermocouple to warm up. If not, the

gas supply will be interrupted.

Adjust the flame after it is regular.

If after some tries the burner does

not light, check if the crown and

its cap are in correct positions.

Burner cap and crown

Thermocouple

Ignition candle

Burner cap

Burner crown

Ignition candle

Thermocouple

WARNING!

Do not keep the control knob

pushed for more than 15 sec-

onds.

If the burner does not light after

15 seconds, release the control

knob, turn it into off position and

try to light the burner again after

minimum 1 minute.

In the absence of electricity you

can ignite the burner without elec-

trical device; in this case approach

the burner with a flame, push the

relevant knob down and turn it

counter-clockwise to maximum

gas release position.

If the burner accidentally goes out,

turn the control knob to the off

position and try to light the burner

again after minimum 1 minute.

The spark generator can start au-

tomatically when you switch on

the mains, after installation or a

power cut. It is normal.

4.2 Turning the burner off

To put the flame out, turn the knob to the

symbol

ENGLISH 7

WARNING!

Always turn the flame down or

switch it off before you remove the

pans from the burner.

5. HELPFUL HINTS AND TIPS

WARNING!

Refer to the Safety chapters.

5.1 Energy savings

• If possible, always put the lids on the

pans.

• When the liquid starts to boil, turn down

the flame to barely simmer the liquid.

Use cookware with diameters applicable

to the size of burners.

Burner Diameters

of cookware

Triple Crown 180 - 260

Semi-rapid (rear left) 120 - 240

Semi-rapid (rear right) 120 - 240

Semi-rapid (front right) 120 - 180

Auxiliary 80 - 180 mm

WARNING!

Do not use cast iron pans, pot-

stones, grill or toaster plates on

gas burners.

WARNING!

Make sure that the bottoms of

pots do not stand above the con-

trol knobs. If the control knobs are

under the bottoms of pots, the

flame heats them up.

Do not put the same pan on two

burners.

WARNING!

Make sure that pot handles is not

above the front edge of the cook-

top. Make sure that pots are cen-

trally put on the rings in order to

get maximum stability and to get

lower gas consumption.

Do not put unstable or damaged pots on

the rings to prevent from spill and injury.

WARNING!

Do not use a flame diffuser.

WARNING!

Liquids spilt during cooking can

cause the glass to break

6. CARE AND CLEANING

WARNING!

Refer to the Safety chapters.

www.electrolux.com

WARNING!

Deactivate the appliance and let it

cool down before you clean it.

Disconnect the appliance from the

electrical supply before you do

cleaning or maintenance work.

Scratches or dark stains on the

surface have no effect on how the

appliance operates.

• You can remove the pan supports to

easily clean the hob.

• To clean the enamelled parts, cap and

crown, wash them with warm soapy

water and dry them carefully before you

put them back.

• Wash stainless steel parts with water,

and then dry them with a soft cloth.

• The pan supports are not dishwasher

proof. They must be washed by hand.

• When you wash the pan supports by

hand, take care when you dry them as

the enamelling process occasionally

leaves rough edges. If necessary, re-

move stubborn stains using a paste

cleaner.

• Make sure you position the pan sup-

ports correctly after cleaning.

• To make the burners work correctly,

make sure that the arms of the pan

supports are in the centre of the burner.

•

Be very careful when you replace

the pan supports to prevent the hob

top from damage.

After cleaning, dry the appliance with a

soft cloth.

Removing the dirt:

– Remove immediately: melting

plastic, plastic foil, and food con-

taining sugar.

– Stop the appliance and let it

cool down before you clean: lime-

scale rings, water rings, fat stains,

shiny metallic discolorations. Use a

special cleaner applicable for sur-

face of hob.

Clean the appliance with a damp

cloth and some detergent.

At the end rub the appliance dry

with a clean cloth.

WARNING!

Do not use knives, scrapers or

similar instruments to clean the

surface of the glass or between

the rims of the burners and the

frame (if applicable).

WARNING!

Do not slide cookware over the

glass because it could scratch the

surface. Also, do not let hard or

sharp objects fall onto the glass or

hit the edge of the hob.

6.1 Cleaning of the spark plug

This feature is obtained through a ceramic

ignition candle with a metal electrode.

Keep these components well clean to

prevent difficult lighting and check that the

burner crown holes are not obstructed.

6.2 Periodic maintenance

Periodically speak your local Service

Force Centre to check the conditions of

the gas supply pipe and the pressure ad-

juster, if fitted.

ENGLISH 9

7. TROUBLESHOOTING

Problem Possible cause Remedy

There is no spark when

lighting the gas

• There is no electrical

supply

• Make sure that the unit

is connected and the

electrical supply is

switched on.

• Control the fuse. If the

fuse is released more

than one time, refer to

a qualified electrician.

• Burner cap and crown

are placed uneven

• Make sure that the

burner cap and crown

are in correct positions.

The flame is blow out im-

mediately after ignition

• Thermocouple is not

heated sufficient

• After lightning the

flame, keep the knob

pushed for approxi-

mately 5 seconds.

The gas ring burns un-

evenly

• Burner crown is

blocked with food resi-

dues

• Make sure that the in-

jector is not blocked

and the burner crown

is clear of food parti-

cles.

If there is a fault, first try to find a solution

to the problem yourself. If you cannot find

a solution to the problem yourself, speak

your dealer or the local Service Force

Centre.

If you operated the appliance in-

correctly, or the installation was

not carried out by a registered en-

gineer, the visit from the customer

service technician or dealer may

not take place free of charge,

even during the warranty period.

These data are necessary to help you

quickly and correctly. These data are

available on the supplied rating plate.

• Model description .................

• Product number (PNC) .................

• Serial Number (S.N.) .................

Use the original spare parts only. They are

available at Service Force Centre and ap-

proved spare parts shops.

7.1 Labels supplied with the

accessories bag

Stick the adhesive labels as indicated be-

low:

www.electrolux.com

MOD.

PROD.NO.

SER.NO

DATA

MOD.

PROD.NO.

SER.NO

DATA

MODELMODEL

MOD.

PROD.NO.

SER.NO.

03 IT

MADE IN ITALY

TYPE

230V-50Hz

IP20

0049

1 2 3

Stick it on Guarantee Card and send

this part

Stick it on Guarantee Card and keep

this part

Stick it on instruction booklet

8. INSTALLATION

WARNING!

Refer to the Safety chapters.

WARNING!

The following instructions about

installation, connection and main-

tenance must be carried out by

qualified personnel in compliance

with standards and local regula-

tions in force.

8.1 Gas Connection

Choose fixed connections or use a flexible

pipe in stainless steel in compliance with

the regulation in force. If you use flexible

metallic pipes, be careful they do not

come in touch with mobile parts or they

are not squeezed. Also be careful when

the hob is put together with an oven.

Make sure that the gas supply

pressure of the appliance obeys

the recommended values. The ad-

justable connection is fixed to the

comprehensive ramp by means of

a threaded nut G 1/2". Screw the

parts without force, adjust the

connection in the necessary direc-

tion and tighten everything.

ABC

End of shaft with nut

Washer

Elbow

Rigid connection:

Carry out connection by using metal rigid

pipes (copper with mechanical end).

ENGLISH 11

"Flexible" connection with

mechanical end:

– Natural gas: connection carry out with

a flexible pipe with mechanical end

which is screwed directly on the elbow

finishing the slope of the appliance.

– Butane / Propane: use a flexible tube,

equipped with it's collars if it is worth

visiting over all it's length and if the ap-

pliance runs only on butane. If the ap-

pliance runs on Propane, use a flexible

pipe with suitable metal end.

Flexible nonmetal pipes

connection:

If it is possible to easily control the con-

nection in its full area, you can use a flexi-

ble pipe. Tightly attach the flexible pipe by

clamps.

Liquid gas: use the rubber pipe holder.

Always engage the gasket. Then continue

with the gas connection. The flexible pipe

is prepared for apply when:

– it can not get hot more than room tem-

perature, higher than 30°C;

– it is no longer than 1500 mm;

– it shows no throttles;

– it is not subject to traction or torsion;

– it does not get in touch with cutting

edges or corners;

– it can be easily examined in order to

check its condition.

The control of preservation of the flexible

pipe consists in checking that:

– it does not show cracks, cuts, marks of

burnings on the two ends and on its full

length;

– the material is not hardened, but shows

its correct elasticity;

– the fastening clamps are not rusted;

–expired term is not due.

If one or more defects are visible, do not

repair the pipe, but replace it.

When installation is complete,

make sure that the seal of each

pipe fitting is correct. Use a soapy

solution, not a flame!

8.2 Injectors replacement

Remove the pan supports.

Remove the caps and crowns of the

burner.

With a socket spanner 7 remove the

injectors and replace them with the

ones which are necessary for the type

of gas you use (see table in "Techni-

cal Information" chapter).

Assemble the parts, follow the same

procedure backwards.

Replace the rating plate (it is near the

gas supply pipe) with the one for the

new type of gas supply. You can find

this plate in the package supplied

with the appliance.

If the supply gas pressure is changeable

or different from the necessary pressure,

you must fit an applicable pressure ad-

juster on the gas supply pipe.

8.3 Adjustment of minimum level

To adjust the minimum level of the burn-

ers:

Light the burner.

Turn the knob on the minimum posi-

tion.

Remove the knob.

With a thin screwdriver, adjust the by-

pass screw position.

The by-pass screw

• If you change from natural gas G20/

G25 20/25 mbar to liquid gas, fully

tighten the by-pass screw in.

• If you change from liquid gas to natural

gas G20/G25 20/25 mbar, undo the

by-pass screw approximately 1/4 of a

turn (1/2 of a turn for Triple Crown

burner).

WARNING!

Make sure the flame does not go

out when you quickly turn the

knob from the maximum position

to the minimum position.

www.electrolux.com

8.4 Electrical connection

• Ground the appliance according to

safety precautions.

• Make sure that the rated voltage and

type of power on the rating plate agree

with the voltage and the power of the

local power supply.

• This appliance is supplied with a mains

cable. It has to be supplied with a cor-

rect plug, able to support the load

marked on the rating plate. The plug

has to be fitted in a correct socket.

• Any electrical component must be in-

stalled or replaced by the Service Force

Centre technician or qualified service

personnel.

• Always use a correctly installed shock-

proof socket.

• Make sure that there is an access to

the mains plug after installation.

• Do not pull the mains cable to discon-

nect the appliance. Always pull the

mains plug.

• The appliance must not be connected

with an extension cable, an adapter or

a multiple connection (risk of fire).

Check that the ground connection is in

conformity with the standard and regu-

lations force.

• The power cable must be placed in

such a way that it does not touch any

hot part.

• Connect the appliance to the mains

with a device that lets to disconnect the

appliance from the mains at all poles

with a contact opening width of mini-

mum 3 mm, eg. automatic line protect-

ing cut-out, earth leakage trips or fuse.

• None of a parts of the connection cable

can not get a temperature 90 °C. The

blue neutral cable must be connected

to the terminal block label with "N". The

brown (or black) phase cable (fitted in

the terminal block contact marked with

"L") must always be connected to the

live phase.

8.5 Replacement of the

connection cable

To replace the connection cable use only

H05V2V2-F T90 or equivalent type. Make

sure that the cable section is applicable to

the voltage and the working temperature.

The yellow/green earth wire must be ap-

proximately 2 cm longer than the brown

(or black) phase wire.

8.6 Building In

min.

55 mm

min.

650 mm

560 mm

480 mm

min.

450 mm

30 mm

supplied seal

supplied brackets

CAUTION!

Install the appliance only on a

worktop with flat surface.

8.7 Possibilities for insertion

Kitchen unit with door

The panel installed below the hob must

be easy to remove and let an easy access

in case a technical assistance intervention

is necessary.

ENGLISH 13

min 20 mm

(max 150 mm)

30 mm

60 mm

Removable panel

Space for connections

Kitchen unit with oven

The hob recess dimensions must obey

the indication and the kitchen unit must

be equipped with vents to let a continu-

ous supply of air. The electrical connec-

tion of the hob and the oven must be in-

stalled separately for safety reasons and

to let easy remove oven from the unit.

50 cm

360 cm

180 cm

120 cm

9. TECHNICAL INFORMATION

Hob dimensions

Width: 740 mm

Length: 510 mm

Hob recess dimensions

Width: 560 mm

Length: 480 mm

Heat input

Triple Crown burner: 3.8 kW

Semi-rapid burner: 1.9 kW

Auxiliary burner: 1.0 kW

TOTAL POWER: G20/G25 (2E+) 20/25 mbar = 10.5 kW

G30 (3+) 28-30 mbar = 763 g/h

G31 (3+) 37 mbar = 750 g/h

Electric supply: 230 V ~ 50 Hz

Category: II2E+3+

Gas connection: G 1/2"

Gas supply: G20/G25 (2E+) 20/25 mbar

Appliance class: 3

By-pass diameters

Burner Ø By-pass in

1/100 mm

Auxiliary 28

Burner Ø By-pass in

1/100 mm

Semi-rapid 32

Triple Crown 56

www.electrolux.com

Gas burners

BURN

NOR-

MAL

POW-

RE-

DUCED

POW-

NORMAL POWER

NATURAL GAS

G20/G25 (2E+) 20/25

mbar

LPG (Butane/Propane)

G30/G31 (3+) 28-30/37

mbar

kW kW

inj.

1/100

G20

mbar

G25

mbar

inj.

1/100

G30

28-30

mbar

G31

mbar

m³/h m³/h g/h g/h

Auxili-

ary

1.0 0.33 70 0.095 0.111 50 73 71

Semi-

rapid

1.9 0.45 96 0.181 0.210 71 138 136

Triple

Crown

3.8 1.4 146 0.362 0.421 98 276 271

10. ENVIRONMENT CONCERNS

Recycle the materials with the symbol

. Put the packaging in applicable

containers to recycle it.

Help protect the environment and human

health and to recycle waste of electrical

and electronic appliances. Do not dispose

appliances marked with the symbol

with the household waste. Return the

product to your local recycling facility or

contact your municipal office.

ENGLISH 15

SOMMAIRE

1. CONSIGNES DE SÉCURITÉ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2. INSTRUCTIONS DE SÉCURITÉ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3. DESCRIPTION DE L'APPAREIL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4. UTILISATION QUOTIDIENNE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

5. CONSEILS UTILES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

6. ENTRETIEN ET NETTOYAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

7. EN CAS D'ANOMALIE DE FONCTIONNEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

9. CARACTERISTIQUES TECHNIQUES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

NOUS PENSONS À VOUS

Merci d'avoir choisi ce produit Electrolux. Avec ce produit, vous bénéficiez de dizaines d'années

d'expérience professionnelle et d'innovation. Ingénieux et élégant, il a été conçu sur mesure pour

vous. Grâce à cet appareil, vous savez que chaque utilisation vous apportera satisfaction.

Bienvenue chez Electrolux.

Visitez notre site Internet pour :

Obtenir des conseils d'utilisation, des brochures, de l'aide, des informations :

www.electrolux.com

Enregistrer votre produit pour obtenir un meilleur service :

www.electrolux.com/productregistration

Acheter des accessoires, consommables et pièces de rechange d'origine pour votre

appareil :

www.electrolux.com/shop

SERVICE APRÈS-VENTE

N'utilisez que des pièces de rechange d'origine.

Avant de contacter le service, assurez-vous de disposer des informations suivantes :

Vous trouverez ces informations sur la plaque signalétique. Modèle, PNC, numéro de série.

Avertissement/Attention : consignes de sécurité.

Informations générales et conseils

Informations écologiques

Sous réserve de modifications.

www.electrolux.com

1. CONSIGNES DE SÉCURITÉ

Avant d'installer et d'utiliser cet appareil, lisez soigneuse-

ment les instructions fournies. Le fabricant ne peut être

tenu pour responsable des dommages et blessures liés à

une mauvaise installation ou utilisation. Conservez tou-

jours cette notice avec votre appareil pour vous y référer

ultérieurement.

1.1 Sécurité des enfants et des personnes

vulnérables

AVERTISSEMENT

Risque d'asphyxie, de blessure ou d'invalidité per-

manente.

• Cet appareil peut être utilisé par des enfants de plus de

8 ans, ainsi que des personnes dont les capacités phy-

siques, sensorielles et mentales sont réduites ou dont

les connaissances et l'expérience sont insuffisantes, à

condition d'être surveillés par une personne responsa-

ble de leur sécurité.

• Ne laissez pas les enfants jouer avec l'appareil.

• Ne laissez pas les emballages à la portée des enfants.

• Tenez les enfants et les animaux éloignés de l'appareil

lorsqu'il est en cours de fonctionnement ou lorsqu'il re-

froidit. Les parties accessibles sont chaudes.

• Si l'appareil est équipé d'un dispositif de sécurité en-

fants, nous vous recommandons de l'activer.

• Les enfants ne doivent pas nettoyer ni entreprendre

une opération de maintenance sur l'appareil sans sur-

veillance.

1.2 Sécurité générale

• L'appareil et ses parties accessibles deviennent

chauds pendant son fonctionnement. Ne touchez pas

les éléments chauffants.

FRANÇAIS 17

• Ne faites pas fonctionner l'appareil avec un minuteur

externe ou un système de commande à distance.

• Il peut être dangereux de laisser chauffer de la graisse

ou de l'huile sans surveillance sur une table de cuisson

car cela pourrait provoquer un incendie.

• N'essayez jamais d'éteindre un feu avec de l'eau. Met-

tez à l'arrêt l'appareil puis couvrez les flammes, par

exemple avec un couvercle ou une couverture ignifuge.

• N'entreposez rien sur les surfaces de cuisson.

• N’utilisez pas de nettoyeur vapeur pour nettoyer l'ap-

pareil.

• Ne posez pas d'objets métalliques tels que couteaux,

fourchettes, cuillères ou couvercles sur la table de cuis-

son car ils pourraient chauffer.

• Si la surface vitrocéramique est fissurée, mettez à l'ar-

rêt l'appareil pour éviter tout risque d'électrocution.

INSTRUCTIONS DE SÉCURITÉ

Cet appareil est adapté aux marchés

suivants : FR

2.1 Installation

AVERTISSEMENT

L'appareil doit être installé unique-

ment par un professionnel qualifié.

• Retirez l'intégralité de l'emballage.

• N'installez pas et ne branchez pas un

appareil endommagé.

• Suivez scrupuleusement les instructions

d'installation fournies avec l'appareil.

• Respectez la distance minimale requise

avec les autres appareils et éléments.

• Soyez toujours vigilants lorsque vous

déplacez l'appareil car il est lourd. Por-

tez toujours des gants de sécurité.

• Isolez les surfaces découpées à l'aide

d'un matériau d'étanchéité pour éviter

que la moisissure ne provoque de gon-

flements.

• Protégez la partie inférieure de l'appa-

reil de la vapeur et de l'humidité.

• N'installez pas l'appareil près d'une

porte ou sous une fenêtre. Les réci-

pients chauds risqueraient de tomber

de l'appareil lors de l'ouverture de cel-

les-ci.

• Si l'appareil est installé au-dessus de ti-

roirs, assurez-vous qu'il y a suffisam-

ment d'espace entre le fond de l'appa-

reil et le tiroir supérieur pour que l'air

puisse circuler.

• Le dessous de l'appareil peut devenir

très chaud. Nous vous recommandons

d'installer un panneau de séparation

ignifuge sous l'appareil pour en bloquer

l'accès.

Branchement électrique

AVERTISSEMENT

Risque d'incendie ou d'électrocu-

tion.

www.electrolux.com

• L'ensemble des branchements électri-

ques doit être effectué par un techni-

cien qualifié.

• L'appareil doit être relié à la terre.

• Avant toute intervention, assurez-vous

que l'appareil est débranché.

• Utilisez le câble d'alimentation électri-

que approprié.

• Ne laissez pas le câble d'alimentation

s'emmêler.

• Assurez-vous que le câble d'alimenta-

tion ou la fiche (si présente) n'entrent

pas en contact avec les surfaces brû-

lantes de l'appareil ou les récipients

brûlants lorsque vous branchez l'appa-

reil à des prises électriques situées à

proximité.

• Assurez-vous que l'appareil est bien in-

stallé. Un câble d'alimentation lâche et

inapproprié ou une fiche (si présente)

non serrée peuvent être à l'origine

d'une surchauffe des bornes.

• Assurez-vous qu'une protection anti-

électrocution est installée.

• Utilisez un collier anti-traction sur le câ-

ble.

• Veillez à ne pas endommager la fiche

secteur (si présente) ni le câble d'ali-

mentation. Contactez le service après-

vente ou un électricien pour remplacer

le câble d'alimentation s'il est endom-

magé.

• L'installation électrique doit être équi-

pée d'un dispositif d'isolement à cou-

pure omnipolaire. Le dispositif d'isole-

ment doit présenter une distance d'ou-

verture des contacts d'au moins 3 mm.

• N'utilisez que des systèmes d'isolation

appropriés : des coupe-circuits, des fu-

sibles (les fusibles à visser doivent être

retirés du support), un disjoncteur diffé-

rentiel et des contacteurs.

Raccordement au gaz

• Tous les raccordements au gaz doivent

être effectués par une personne quali-

fiée.

• Assurez-vous que l'air circule autour de

l'appareil.

• Les informations concernant l'alimenta-

tion en gaz se trouvent sur la plaque si-

gnalétique.

• Cet appareil n'est pas raccordé à un

dispositif d'évacuation des produits de

combustion. Assurez-vous de brancher

l'appareil selon les réglementations

d'installation en vigueur. Veillez à res-

pecter les exigences en matière d'aéra-

tion.

2.2 Utilisation

AVERTISSEMENT

Risque de blessures, de brûlures

ou d'électrocution.

• Utilisez cet appareil dans un environne-

ment domestique.

• Ne modifiez pas les caractéristiques de

cet appareil.

• Ne laissez jamais l'appareil sans surveil-

lance pendant son fonctionnement.

• N'utilisez jamais cet appareil avec les

mains mouillées ou lorsqu'il est en con-

tact avec de l'eau.

• Ne posez pas de couverts ou de cou-

vercles sur les zones de cuisson. Elles

sont chaudes.

• Éteignez les zones de cuisson après

chaque utilisation.

• N'utilisez jamais l'appareil comme plan

de travail ou comme plan de stockage.

• Si la surface de l'appareil présente des

fêlures, débranchez immédiatement

l'appareil pour éviter tout risque d'élec-

trocution.

AVERTISSEMENT

Risque d'explosion ou d'incendie.

• Les graisses et l'huile chaude peuvent

dégager des vapeurs inflammables. Te-

nez les flammes ou les objets chauds

éloignés des graisses et de l'huile lors-

que vous vous en servez pour cuisiner.

• Les vapeurs dégagées par l'huile très

chaude peuvent provoquer une com-

bustion spontanée.

• L'huile qui a servi contient des restes

d'aliments qui peuvent provoquer un in-

cendie à température plus faible que

l'huile n'ayant jamais servi.

• Ne placez pas de produits inflamma-

bles ou d'éléments imbibés de produits

inflammables à l'intérieur, à proximité

ou sur l'appareil.

FRANÇAIS 19

AVERTISSEMENT

Risque de dommage de l'appareil.

• Ne laissez pas de récipients chauds sur

le bandeau de commande.

• Ne laissez pas le contenu des réci-

pients de cuisson s'évaporer.

• Prenez soin de ne pas laisser tomber

d'objets ou de récipients sur l'appareil.

Sa surface risque d'être endommagée.

• Ne faites jamais fonctionner les zones

de cuisson avec des récipients de cuis-

son vides ou sans aucun récipient de

cuisson.

• Ne placez jamais de papier aluminium

sur l'appareil.

• N'utilisez pas de récipients en fonte ou

en aluminium, ni de récipients dont le

fond est endommagé et rugueux. Ils ris-

queraient de rayer la surface vitrocéra-

mique. Soulevez toujours ces objets

lorsque vous devez les déplacer sur la

surface de cuisson.

• Veillez à ce que la pièce où est installé

l'appareil soit bien aérée.

• Assurez-vous que les orifices de venti-

lation ne sont pas bouchés.

• Utilisez uniquement des récipients sta-

bles avec une forme adaptée et un plus

grand diamètre que les dimensions des

brûleurs. Risque de surchauffe et de

rupture de la plaque en verre (si votre

appareil en est équipé) !

• Assurez-vous que la flamme ne s'éteint

pas lorsque vous tournez rapidement la

manette de la position maximale à la

position minimale.

• Veillez à ce que les récipients se trou-

vent bien au centre des cercles et qu'ils

ne dépassent pas des rebords de la ta-

ble de cuisson.

• N'utilisez que les accessoires fournis

avec l'appareil.

• N'installez pas de diffuseur de flamme

sur le brûleur.

2.3 Entretien et nettoyage

AVERTISSEMENT

Risque d'endommagement de

l'appareil.

• Nettoyez régulièrement l'appareil afin

de maintenir le revêtement en bon état.

• Ne pulvérisez pas d'eau ni de vapeur

pour nettoyer l'appareil.

• Ne lavez pas les brûleurs au lave-vais-

selle.

• Nettoyez l'appareil avec un chiffon doux

humide. Utilisez uniquement des pro-

duits de lavage neutres. N'utilisez pas

de produits abrasifs, de tampons à ré-

curer, de solvants ou d'objets métalli-

ques.

2.4 Mise au rebut

AVERTISSEMENT

Risque de blessure ou d'asphyxie.

• Contactez votre service municipal pour

obtenir des informations sur la marche

à suivre pour mettre conformément

l'appareil au rebut.

• Débranchez l'appareil de l'alimentation

électrique.

• Coupez le câble d'alimentation au ras

de l'appareil et mettez-le au rebut.

• Aplatissez les tuyaux de gaz externes.

www.electrolux.com

La page charge ...

Electrolux EGW7353NOX Manuel utilisateur

Marque: Electrolux

Modèle: EGW7353NOX

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Electrolux EGW7353NOX User manual

Documents connexes

Autres documents

Aeg-Electrolux HG795540XB Manuel utilisateur