Ashley Hearth Products VG5790 Manuel utilisateur

Marque: Ashley Hearth Products

Modèle: VG5790

Catégorie: Poêles

Taper: Manuel utilisateur

Ce manuel convient également à

French version is available for download from the U.S. Stove website: http://www.usstove.com/

Version française est disponible pour téléchargement à partir du site U.S. Stove: http://www.usstove.com

This unit is not intended to be used as a primary source of heat.

OWNER’S MANUAL

MODEL: AP5780

852925-0804G

• Please read this entire manual before installation and use of this appliance. Failure to

follow these instructions could result in property damage, bodily injury, or even death.

• Contactyourlocalbuildingorreofcialsaboutobtainingpermits,restrictionsand

installation inspection requirements in your area.

• Save these instructions.

U.S. Stove Company

227 Industrial Park Road, South Pittsburg, TN 37380

Phone 800-750-2723 www.usstove.com

Certiedforinstallationsinthe

USA and Canada.

U.S. Environmental Protection Agency

Certiedtocomplywith2015particulate

emissions standards.

ReportNo.0215PS061E

0215PS061S

-2-

ThismanualdescribestheinstallationandoperationoftheAshley,AP5780woodheater.Thisheatermeetsthe2015U.S.

EnvironmentalProtectionAgency’scribwoodemissionlimitsforwoodheaterssoldafterMay15,2015.Underspecictest

conditionsthisheaterhasbeenshowntodeliverheatatratesrangingfrom8,507to26,386Btu/hr.Thisheaterachieved

aparticulateemissionsrateof1.3g/hrwhentestedtomethodASTME2779-10(*andanefciencyof72%).

• IMPORTANT:Readthisentiremanualbeforeinstalling

and operating this product. Failure to do so may

result in property damage, bodily injury, or even

death. Proper installation of this stove is crucial for

safeandefcientoperation.

• Installventatclearancesspeciedbythevent

manufacturer.

• Do not connect the pellet vent to a vent serving any

other appliance or stove.

• Donotinstallauedamperintheexhaustventing

system of this unit.

• Use of outside air is not required for this unit.

• Contactyourlocalbuildingofcialstoobtaina

permit and information on any additional installation

restrictions or inspection requirements in your area.

• Do not throw this manual away. This manual has

important operating and maintenance instructions

that you will need at a later time. Always follow the

instructions in this manual.

• This appliance is designed for the use of pelletized

fuelthatmeetorexceedthestandardsetbythe

PelletFuelInstitute(PFI).

• Never use gasoline, gasoline-type lantern fuel,

kerosene,charcoallighteruid,orsimilarliquidsto

startor’freshenup’areinthisstove.Keepallsuch

liquids well away from the stove while it is in use.

• A working smoke detector must be installed in the

same room as this product.

• Installasmokedetectoroneachoorofyourhome;

incaseofaccidentalrefromanycauseitcan

provide time for escape.

• Thesmokedetectormustbeinstalledatleast15

feet(4,57M)fromtheapplianceinordertoprevent

undue triggering of the detector when reloading.

• Do not unplug the stove if you suspect a malfunction.

TurntheON/OFFSWITCHto”OFF’andcontactyour

dealer.

• Your stove requires periodic maintenance and

cleaning(see”MAINTENANCE”).Failuretomaintain

your stove may lead to improper and/or unsafe

operation.

• Disconnect the power cord before performing any

maintenance!NOTE:TurningtheON/OFFSwitchto

”OFF”doesnotdisconnectallpowertotheelectrical

components of the stove.

• Never try to repair or replace any part of the stove

unless instructions for doing so are given in this

manual. All other work should be done by a trained

technician.

• Do not operate your stove with the viewing door

open. The auger will not feed pellets under these

circumstances and a safety concern may arise from

sparks or fumes entering the room.

• Allow the stove to cool before performing any

maintenance or cleaning. Ashes must be disposed

inametalcontainerwithatightttinglid.Theclosed

container of ashes should be placed on a non-

combustible surface or on the ground, well away

fromallcombustiblematerials,pendingnaldisposal.

• Theexhaustsystemshouldbecheckedmonthly

during the burning season for any build-up of soot or

creosote.

• Donottouchthehotsurfacesofthestove.Educate

all children on the dangers of a high-temperature

stove. Young children should be supervised when

they are in the same room as the stove.

• The hopper and stove top will be hot during

operation;therefore,youshouldalwaysusesome

type of hand protection when refuelling your stove.

• A power surge protector is required. This unit must be

pluggedintoa110-120V,60Hzgroundedelectrical

outlet. Do not use an adapter plug or sever the

grounding plug. Do not route the electrical cord

underneath, in front of, or over the heater. Do not

routethecordinfoottrafcareasorpinchthecord

under furniture.

• The heater will not operate during a power outage.

If a power outage does occur, check the heater for

smoke spillage and open a window if any smoke spills

into the room.

• The feed door must be closed and sealed during

operation.

• Neverblockfreeairowthroughtheopenventsof

the unit.

• Keepforeignobjectsoutofthehopper.

• The moving parts of this stove are propelled by high

torqueelectricmotors.Keepallbodypartsaway

from the auger while the stove is plugged into an

electrical outlet. These moving parts may begin to

move at any time while the stove is plugged in.

• Donotplaceclothingorotherammableitemsonor

near this stove.

• Wheninstalledinamobilehome,thestovemustbe

grounded directly to the steel chassis and bolted

totheoor.WARNING—THISUNITMUSTNOTBE

INSTALLEDINTHEBEDROOM(perHUDrequirements).

CAUTION—Thestructuralintegrityofthemobilehome

oor,wall,andceiling/roofmustbemaintained.

• This appliance is not intended for commercial use.

• CAUTION:Burningfuelcreatescarbonmonoxide

and can be hazardous to your health if not properly

vented.

*Thisapplianceisafreestandingheater.Itisnotintendedtobeattachedtoanytypeofducting.Itisnotafurnace.

Safety Precautions

-3-

*Pelletsizemayeffecttheactualrateoffuelfeedandburntimes.Fuelfeedratesmayvarybyasmuchas20%.

Use PFI listed fuel for best results.

FUEL CONSIDERATIONS

Your pellet stove is designed to burn premium hardwood pellets that comply with Association of Pellet Fuel

Industriesstandards.(Minimumof40lbsdensitypercubicft,1/4”to5/16”diameter,lengthnogreaterthan1.5”,

notlessthan8,200BTU/lb,moistureunder8%byweight,ashunder1%byweight,andsaltunder300partsper

million).Pelletsthataresoft,containexcessiveamountsofloosesawdust,havebeen,orarewet,willresultin

reduced performance.

Storeyourpelletsinadryplace.DONOTstorethefuelwithintheinstallationclearancesoftheunitorwithinthe

spacerequiredforrefuellingandashremoval.Doingsocouldresultinahousere.

Donotoverreorusevolatilefuelsorcombustibles,doingsomaycauseapersonalandpropertydamage

hazards.

SAFETY AND EPA COMPLIANCE

Your pellet stove has been approved for installation in the USA and Canada. It may also be installed in a

manufacturedormobilehome.YourstoveconformstoASTME1509-12,andCertiedtoULCS627-00,and(UM)

84-HUD.

ElectricalSpecications

ElectricalRating 120VoltsAC,60HZ,3Amps

Watts(operational) 125W

Watts(igniterrunning) 310W

Dimensions

Height 37.16”(944mm)

Width 20.81”(529mm)

Depth 22.25”(566mm)

Weight 162lbs

Specications

WARNING:Itisagainstfederalregulationstooperatethiswoodheaterinamannerinconsistentwiththe

operatinginstructionsintheowner’smanual.

Note:Registeryourproductonlineatwww.usstove.com.See“LimitedWarranty”sectionforspecicwarranty

information for your new purchase. Save your receipt with your records for any claims.

HeatingSpecications

FuelBurnRate*(lowestsetting) 1.4lbsperhr

BurnTime(lowestsetting) 32 hrs

HopperCapacity 46lbs

Flue Size 3“or4”(77mmto102mm)

-4-

INSTALLATION OPTIONS

Read this entire manual before you install and use your pellet stove. Failure to follow instructions may result in

property damage, bodily injury, or even death!

(Seespecicinstallationdetailsforclearancesandotherinstallationrequirements)

AFreestandingUnit—supportedbypedestal/legsandplacedonanon-combustibleoorsurfaceincompliance

with clearance requirements for a freestanding stove installation.

Yourpelletstovemaybeinstalledtocodeineitheraconventionalormobilehome(seeSPECIALMOBILEHOME

REQUIREMENTS).TheinstallationmustcomplywiththeManufacturedHomeandSafetyStandard(HUD),CFR3280,

Part 24.

Itisrecommendedthatonlyaauthorizedtechnicianinstallyourpelletstove,preferablyanNFIcertiedspecialist.

DONOTCONNECTTHISUNITTOANYAIRDISTRIBUTIONDUCTORSYSTEM.

The use of other components other than stated herein could cause bodily harm, heater damage, and void your

warranty.

IMPROPERINSTALLATION:Themanufacturerwillnotbeheldresponsiblefordamagecausedbythemalfunction

ofastoveduetoimproperventingorinstallation.Call(800)750-2723and/orconsultaprofessionalinstallerifyou

have any questions.

CLEARANCES

Your pellet stove has been tested and listed for installation in residential, mobile home in accordance with the

clearances given below. For safety reasons, please adhere to the installation clearances and restrictions. Any

reduction in clearance to combustibles may only be done by means approved by a regulatory authority.

Installation

CLEARANCES

inches mm

A SideWalltoStove 8 204

B SideWalltoVentPipe 12 305

C BackWalltoStove 12 305

D BackWalltoVentPipe 3 77

E Ceiling to Floor 84 2134

F Ceiling to Stove 46.875 1191

CORNERCLEARANCES

G SideWalltoStove 10 254

H SideWalltoVentPipe 3 77

I BackWalltoStove 10 254

J BackWalltoVentPipe 3 77

ADJACENT WALL

THROUGH THE WALL

INSTALLATION

INTERIOR VERTICAL

INSTALLATION

ADJACENT WALL

THROUGH THE WALL

INSTALLATION

INTERIOR VERTICAL

INSTALLATION

ADJACENT WALL

THROUGH THE WALL

INSTALLATION

INTERIOR VERTICAL

INSTALLATION

-5-

FLOOR PROTECTION

Thisheatermusthaveanon-combustibleoorprotector(UL1618emberprotection)installedbeneathitifthe

oorisofcombustiblematerial.US:FloorprotectorshouldbeULlistedorequaltoo,needstoextend6”tothefront,6”to

eachside,1”totherearoftheunit.Underand2”beyondeachsideofthecleanoutteeifaninteriorverticalinstillation.

Canada:FloorprotectorshouldcomplywithCAN/ULCstandards.Needstoextend18”tothefront,8”beyondeachsideof

the unit.

Installation

FLOORPROTECTORDIMENSIONS

K BacktoStove 1”(26mm)U.S.(8”(204mm)Can.)

L Side to Stove 6”(153mm)U.S.(8”(204mm)Can.)

M Front to Stove 6”(153mm)U.S.(18”(458mm)Can.)

N BackandSidestoFlue 6”(153mm)

ADJACENT WALL

THROUGH THE WALL

INSTALLATION

INTERIOR VERTICAL

INSTALLATION

-6-

VENTING REQUIREMENTS

• Installventatclearancesspeciedbytheventmanufacturer.

• Do not connect the pellet vent to a vent serving any other appliance or stove.

• Donotinstallauedamperintheexhaustventingsystemofthisunit.

• The following installation guidelines must be followed to ensure conformity with both the safety listing of this

stove and to local building codes. Do not use makeshift methods or compromise in the installation.

MAXIMUM VENTING DISTANCE

InstallationMUSTincludeatleast3-feetofverticalpipeoutsidethehome.Thiswillcreatesomenaturaldraftto

reducethepossibilityofsmokeorodorduringapplianceshutdownandkeepexhaustfromcausinganuisance

orhazardbyexposingpeopleorshrubstohightemperatures.Themaximumrecommendverticalventingheight

is12-feetfor3-inchtype“PL”vent.Totallengthofhorizontalventmustnotexceed4-feet.Thiscouldcauseback

pressure.Usenomorethan180degreesofelbows(two90-degreeelbows,ortwo45-degreeandone90-degree

elbow,etc.)tomaintainadequatedraft.

IMPORTANCE OF PROPER DRAFT

Draft is the force which moves air from the appliance up through the chimney. The amount of draft in your

chimney depends on the length of the chimney, local geography, nearby obstructions and other factors. Too

muchdraftmaycauseexcessivetemperaturesintheappliance.Inadequatedraftmaycausebackpufnginto

theroomand‘plugging’ofthechimney.

Inadequate draft will cause the appliance to leak smoke into the room through appliance and chimney

connectorjoints.Anuncontrollableburnorexcessivetemperatureindicatesexcessivedraft.

Takeintoaccountthechimney’slocationtoinsureitisnottooclosetoneighboursorinavalleywhichmay

cause unhealthy or nuisance conditions.

PELLET VENT TYPE

AULlisted3-inchor4-inchtype“PL”pelletventexhaustsystemmustbeusedforinstallationandattachedtothe

pipeconnectorprovidedonthebackofthestove(usea3-inchto4-inchadapterfor4-inchpipe).Connection

atbackofstovemustbesealedusingHi-TempRTV.Use4-inchventiftheventheightisover12-feetorifthe

installationisover2,500feetabovesealevel.WerecommendtheuseofSimpsonDura-Vent®orMetal-Fab®

pipe(ifyouuseotherpipe,consultyourlocalbuildingcodesand/orbuildinginspectors).DonotuseType-B

Gas Vent pipe or galvanized pipe with this unit. The pellet vent pipe is designed to disassemble for cleaning and

should be checked several times during the burning season. Pellet vent pipe is not furnished with the unit and

must be purchased separately.

PELLET VENT INSTALLATION

Theinstallationmustincludeaclean-outteetoenablecollectionofyashandtopermitperiodiccleaning

of the exhaust system.  90-degree elbows accumulate y ash and soot thereby reducing exhaust ow and

performanceofthestove.Eachelboworteereducesdraftpotentialby30%to50%.

Alljointsintheventsystemmustbefastenedbyatleast3screws,andalljointsmustbesealedwithHi-Temp

RTVsiliconesealanttobeairtight.Theareawheretheventpipepenetratestotheexteriorofthehomemust

besealedwithsiliconeorothermeanstomaintainthevaporbarrierbetweentheexteriorandtheinteriorofthe

home. Vent surfaces can get hot enough to cause burns if touched by children. Noncombustible shielding or

guards may be required.

PELLET VENT TERMINATION

Donotterminatetheventinanenclosedorsemi-enclosedarea,suchas;carport,garage,attic,crawlspace,

under a sun deck or porch, narrow walkway, or any other location that can build up a concentration of fumes.

Termination in one of these areas can also lead to unpredictable pressure situations with the appliance, and

couldresultinimproperperformanceand/ormalfunction.Theterminationmustexhaustabovetheoutsideair

inlet elevation. The termination must not be located where it will become plugged by snow or other materials. Do

notterminatetheventingintoanexistingsteelormasonrychimney.

IMPORTANT:Thisunitisequippedwithanegativedraftsystemthatpullsairthroughtheburnpotandpushes

theexhaustoutofthedwelling.Ifthisunitisconnectedtoauesystemotherthanthewayexplainedinthis

manual, it will not function properly.

Installation

-7-

VENT TERMINATION CLEARANCES

A. Minimum4-foot(1.22m)clearancebeloworbesideanydoororwindowthatopens.

B. Minimum1-foot(0.3m)clearanceaboveanydoororwindowthatopens.

C. Minimum3-foot(0.91m)clearancefromanyadjacentbuilding.

D. Minimum7-foot(2.13m)clearancefromanygradewhenadjacenttopublicwalkways.

E. Minimum2-foot(0.61m)clearanceaboveanygrass,plants,orothercombustiblematerials.

F. Minimum3-foot(0.91m)clearancefromanforcedairintakeofanyappliance.

G. Minimum2-foot(0.61m)clearancebelowevesoroverhang.

H. Minimum1-foot(0.3m)clearancehorizontallyfromcombustiblewall.

I. Mustbeaminimumof3foot(0.91m)abovetheroofand2foot(0.61m)abovethehighestpointortheroof

within10feet(3.05m).

VENTTERMINATION

CLEARANCES

Installation

-8-

Assembly Instructions

Step1

Pull the factory installed wires out of the top of the stove.

There will be two wire harnesses, as shown.

Step 2

Unpack the top mount controls and ensure that the

wiring harness shown is attached securely.

Step 3

Connect the factory installed wiring harnesses to the control

panel as shown.

Step 4

Attach the control panel to the

top of the stove, as shown.

Step 5

Secure with two sheet metal

screws.

-9-

THROUGH THE WALL INSTALLATION (RECOMMENDED

INSTALLATION)

CanadianinstallationsmustconformtoCAN/CSA-B365.

To vent the unit through the wall, connect the pipe

adapter to the exhaust motor adapter. If the exhaust

adapterisatleast18in.(457mm)abovegroundlevel,a

straight section of pellet vent pipe can be used through

the wall.

Your heater dealer should be able to provide you with

a kit that will handle most of this installation, which will

include a wall thimble that will allow the proper clearance

throughacombustiblewall.Onceoutsidethestructure,

a3in.(76mm)clearanceshouldbemaintainedfromthe

outside wall and a clean out tee should be placed on

the pipe with a 90-degree turn away from the house. At

thispoint,a3ft(0.91m)(minimum)sectionofpipeshould

be added with a horizontal cap, which would complete

the installation.

A support bracket should be placed just below the

termination cap or one every 4ft (1.22m) to make the

system more stable. If you live in an area that has heavy

snowfall, it is recommended that the installation be taller

than 3ft (0.91m) to get above the snowdrift line. This

same installation can be used if your heater is below

ground level by simply adding the clean-out section and

verticalpipeinsideuntilgroundlevelisreached.Withthis

installation you have to be aware of the snowdrift line,

deadgrass,andleaves.Werecommenda3ft(0.91m)minimumverticalriseontheinsideoroutsideofthehouse.

The“throughthewall”installationistheleastexpensiveandsimplestinstallation.Neverterminatetheendvent

underadeck,inanalcove,underawindow,orbetweentwowindows.WerecommendSimpsonDura-Vent®

orMetal-Fab®kits.

THROUGH THE ROOF/CEILING INSTALLATION

Whenventingtheheaterthroughtheceiling,thepipeisconnectedthesameasthroughthewall,exceptthe

clean-outteeisalwaysontheinsideofthehouse,anda3in.(76mm)adapterisaddedbeforetheclean-outtee.

Youmustusetheproperceilingsupportangesandroofashing(suppliedbythepipemanufacturer;followthe

pipemanufacturer’sdirections).Itisimportanttonotethatifyourverticalrunofpipeismorethan12ft(3.7m),the

pelletventpipesizeshouldbeincreasedto4in.(102mm)indiameter.

Donotexceedmorethan4ft(1.22m)ofpipeonahorizontalrunanduseasfewelbowsaspossible.Ifanoffset

is required, it is better to install 45-degree elbows rather than 90-degree elbows.

Installation

3” (MIN)

6” (MIN)

TYPICALTHROUGHTHEWALL

INSTALLATION

-10-

SPECIAL MOBILE HOME REQUIREMENTS

• WARNING!-Donotinstallinasleepingroom

• CAUTION!-Thestructuralintegrityofthemobile

homeoor,wall,andceiling/roofmustbe

maintained.

NOTE:Installationshouldbeinaccordancewiththe

ManufacturedHomeandSafetyStandard(HUD),CFR

3280, Part 24.

In addition to the previously detailed installation

requirements, mobile home installations must meet

the following requirements:

• Thisstovemustbesecurelyfastenedtotheoor

of the mobile home through the two holes in the

rearofthestoveusing2,¼”lagboltsthatarelong

enough to go through both a hearth pad, if used,

andtheoorofthehome.

• The heater must be electrically grounded to the

steel chassis of the mobile home with 8 GA copper

wire using a serrated or star washer to penetrate

paint or protective coating to ensure grounding.

• Ventmustbe3or4-inch“PL”Ventandmustextendaminimumor36in.(914mm)abovetherooflineofthe

mobilehomeandmustbeinstalledusingaULlistedceilingrestopandraincap.

• Whenmovingyourmobilehome,allexteriorventingmustberemovedwhilethemobilehomeisbeing

relocated. After relocation, all venting must be reinstalled and securely fastened.

• OutsideAirismandatoryformobilehomeinstallation.SeeOutsideAirSupplysectionandyourdealerfor

purchasing.

• Checkwithyourlocalbuildingofcialsasothercodesmayapply.

NOTE:Dimensionsfromtheoor

toyourstovesinlet/exhaustpipes

areapproximateandmayvary

depending on your installation.

TYPICALFRESHAIR

TERMINATION

EXHAUST/INLET

LOCATIONS

OUTSIDE AIR SUPPLY (OPTIONAL, UNLESS INSTALLING IN A MOBILE HOME)

Adequate ventilation air is required to operate this heater. During operation, the heater draws air for combustion

whichcanbeassistedbytheinstallationofoutsidecombustionairinlets.However,certainweatherconditions

suchasicingoruseofkitchenexhaustfansmayimpactandreducetheeffectivenessofvents.Itisimportantto

note that room air starvation will negatively impact the operation of the heater.

Depending on your location and home construction, outside air may be necessary for optimal performance.

Metalpipe(solidorexible)mustbeusedfortheoutsideairinstallation.PVCpipeisNOTapprovedandshould

NEVERbeused.Awindshieldovertheterminationoftheoutsideairpipeora90-degreeelboworbendaway

fromtheprevailingwindsMUSTbeusedwhenanoutsideairpipeisinstalledthroughthesideofabuilding.The

outsideairterminationMUSTbeatleast1ft(0.305m)awayfromtheexhaustsystemtermination.

Theoutsideairpipeon your heater is2”(50.8mm) OD. The outsideairconnecting pipe must beatleast 2”

(50.8mm)ID.TheoutsideairconnectionusedMUSTNOTrestricttheamountofairavailabletoyourheater.The

outsideairconnectingpipemustbeasshortandfreeofbendsaspossible,anditmusttover,notinside,the

outside air connection to the heater.

Installation

MOBILE HOME

MOUNTING BOLT HOLES

6.46

8.39

7.66

37.36

Fresh Air Intake

Exhaust Outlet

-11-

PANEL CONTROLS

The blowers and automatic fuel supply are controlled from a panel on the top of this unit. The control panel

functions are a follows.

A. ON/OFFSWITCH(“POWER”BUTTON)

• Whenpushed,thestovewillautomaticallyignite.Nootherrestarterisnecessary.Theigniterwillstayon

foratleast10andupto12minutes,dependingonwhenProofofFireisreached.Thereshouldstartin

approximately5minutes.

• Theredlightlocatedabovethe“POWER”buttonwillturngreenwhenpressedandremaingreenuntil

the stove is turned off.

• Afterpushing“POWER”,theaugermotorisonfor3.5minutes,offfor1minute.Duringtheremainderof

thestart-upperiod,theaugermotoroperatesontheheatrange“1”setting.

• Duringstartuptheheatleveladvance(UpandDownkeys)willchangetheheatrangeindicatorlevel

accordingly, but there is no change in the stoves operating conditions until start-up is completed.

• Duringstart-upignitionmustoccurwithin12minutesorthestovewillerroroutandshowE4.

• Duringthestart-upphase,theModekeydoesnotfunction.

B. LEVEL/TEMPARROWBUTTONS

• These buttons when pushed will set the pellet feed rate, hence the heat output or heat range of your

stove.

• Thelevelsofheatoutputwillincrementallychangeonthebargraphstartingfromheatrange“1”to

heatrange“5”.

C. °C/°FButton

• The °C / °F button changes the two digit display from degrees Celsius to degrees Fahrenheit.

D. MODE(M/T)BUTTON

• TheModeofthestovecanbeswitchedbetweenmanualandcontrolledwithaThermostat.Separate

LEDstotheleftofthetwodigitdisplayindicatethemodeofoperation–ManualorT-Stat.Thestovehas

tobeinnormaloperationtobeswitchedfromManualtoT-Statmode.

• Manualmodeoperatesaccordingtothe5setlevelsoffeedonthebargraphfromheatrange“1”to

heatrange“5”.

• T-Stat mode works as follows:

• The stove has a built in Thermostat into the controls of the appliance. The temperature sensor for the

T-Stat is located on the back of the stove behind the display board.

• OncethestovehasgoneintorunmodethestovecanbeswitchintoT-Statmode.

• The Up and Down Level / Temp Arrow buttons are used to change the desired set-point temperature.

Oncethedesiredtemperatureisreachedthetwodigitdisplaywillashforfoursecondsandresetto

the actual room temperature.

• Oncethestovereacheswithin3°Fofthedesiredtemperaturesetpoint,itreturnstotheheatrangethat

thestovewassetonbeforeitwasswitchedtoT-Statmode(ifthestovewasrunningonheatrange“5”

whenswitchedtoT-statmodewhenitgetswithin3°Fofthesetpointitwillreturntoheatrange“5”).

• Oncethestovereachesthedesiredset-point,thestovewilldroptoheatrange“1”.

• Whenroomtemperaturedropsbelowdesiredset-pointthestovewillrampbackupuntilitreachesthe

desired temperature.

Level / Temp

Manual

T-Stat

CONTROLS

Control Panel

-12-

• Donotusechemicalsoruidstostartthere-neverusegasoline,gasoline-typelanternfuel,kerosene,

charcoallighteruid,orsimilarliquidstostartor“freshenup”areinthisstove.Keepallsuchliquidswell

away from the stove while it is in use.

• Hotwhileinoperation.Keepchildren,clothingandfurnitureaway.Contactmaycauseskinburns.

This heater is designed to burn only PFI Premium grade pellets. This appliance can also burn pellets rated as

standardafterMay16,2015.

DONOTBURN:

1. Garbage;

2. Lawnclippingsoryardwaste;

3. Materialscontainingrubber,includingtires;

4. Materialscontainingplastic;

5. Wastepetroleumproducts,paintsorpaintthinners,

orasphaltproducts;

6. Materialscontainingasbestos;

7. Constructionordemolitiondebris;

8. Railroadtiesorpressure-treatedwood;

9. Manureoranimalremains;

10.Salt water driftwood or other previously salt water

saturatedmaterials;

11.Unseasonedwood;or

12.Paper products, cardboard, plywood, or

particleboard. The prohibition against burning

these materials does not prohibit the use of re

starters made from paper, cardboard, saw dust,

wax and similar substances for the purpose of

startingareinanaffectedwoodheater.

Burningthesematerialsmayresultinreleaseoftoxicfumesorrendertheheaterineffectiveandcausesmoke.

PROPER FUEL

Thisstoveisapprovedforburningpelletizedwoodfuelonly!Factory-approvedpelletsarethose1/4”or5/16”

indiameterandnotover1”long.Longerorthickerpelletssometimesbridgetheaugerights,whichprevents

properpelletfeed.Burningwoodinformsotherthanpelletsisnotpermitted.Itwillviolatethebuildingcodesfor

which the stove has been approved and will void all warranties. The design incorporates automatic feed of the

pelletfuelintothereatacarefullyprescribedrate.Anyadditionalfuelintroducedbyhandwillnotincrease

heat output but may seriously impair the stoves performance by generating considerable smoke. Do not burn

wetpellets.Thestove’sperformancedependsheavilyonthequalityofyourpelletfuel.Avoidpelletbrandsthat

display these characteristics:

1. ExcessFines–“Fines”isatermdescribingcrushedpelletsorloosematerialthatlookslikesawdustorsand.

Pelletscanbescreenedbeforebeingplacedinhoppertoremovemostnes.

2. Binders–Somepelletsareproducedwithmaterialstoholdthetogether,or“bind”them.

3. Highashcontent–Poorqualitypelletswilloftencreatesmokeanddirtyglass.Theywillcreateaneedfor

more frequent maintenance. You will have to empty the burn pot plus vacuum the entire system more often.

Poorqualitypelletscoulddamagetheauger.Wecannotacceptresponsibilityfordamageduetopoor

quality pellet.

PRE-START-UP CHECK

Removeburnpot,makingsureitiscleanandnoneoftheairholesareplugged.Cleantherebox,andthen

reinstallburnpot.Cleandoorglassifnecessary(adryclothorpapertowelisusuallysufcient).Neveruseabrasive

cleanersontheglassordoor.Checkfuelinthehopper,andrellifnecessary.

NOTE:Thishoppercanholdupto20lbs.ofpellets.

BUILDING A FIRE

Never use a grate or other means of supporting the fuel. Use only the burn pot supplied with this heater.

Hopperlidmustbeclosedinorderfortheunittofeedpellets.

During the start-up period:

1. Makesureburnpotisfreeofpellets.

2. DONOTopentheviewingdoor.

3. Damper may need to be closed during start up.

4. DONOTaddpelletstotheburnpotbyhand.

NOTE:Duringtherstfewres,yourstovewillemitanodorasthehightemperaturepaintcuresorbecomes

seasonedtothemetal.Maintainingsmallerreswillminimizethis.Avoidplacingitemsonstovetopduringthis

periodbecausepaintcouldbeaffected.Attemptstoachieveheatoutputratesthatexceedheaterdesign

specicationscanresultinpermanentdamagetotheheater.

Operation

-13-

Operation

AUTOMATIC IGNITOR

Fill hopper and clean burn pot.

1. Press“On/Off”button.Makesuregreenlightcomeson.

2. The damper should be completely closed or open no more than ¼ of the way during start-up. This will vary

dependingonyourinstallationandelevation.Oncereisestablishedadjustfordesiredameincreasingthe

amountthedamperisopenastheheatsettingisincreased.(See“DAMPERCONTROL”)

3. Adjustfeedratetodesiredsettingbypressing“HeatLevelAdvance”button.

Ifredoesn’tstartin12minutes,press“On/Off”,waitafewminutes,cleartheburnpot,andstartprocedure

again.

DAMPER CONTROL

The damper control lever is located on the back of the stove on the lower left side. The damper adjusts the

combustion air. This control is necessary due to the varied burn characteristics of individual installations, different

pellet brands and pellet feed rates. It allows you to improve the efciency of your stove. Providing correct

combustion air will reduce the frequency of cleaning your glass door and prevent the rapid buildup of creosote

insideyourstoveandchimney.Youshouldadjustthedamperbasedonthere’sappearance.Alow,reddish,

dirtyrecanbeimprovedbyturningthedamperslightlytotheright.A“blowtorch”recanbeimprovedby

turning the dampener to the left a little bit. As a general rule, on lower feed rate settings, the damper should

befarthertotheleftclosingitoff.Onhigherfeedrates,thedampershouldbeopenmorebyhavingitsetmore

towardstheright.Throughtrialanderror,youwillndthebestsetting.Consultyourdealerifyouneedhelp.

NOTE:Onheatrange“1”,dampershouldbeeithercompletelyclosedoropennomorethana¼oftheway.If

damperisopentofar,itcancausetheretogoout.

OPENING DOOR

If the door is opened while the stove is in operation it must be closed within 30 seconds or the stove will shut

down.Ifthestoveshutsdownpushthe“On/Off”buttontore-startyourstove.Thestovewillhavetofullyshut

down and turn off before you will be able to restart the stove.

ROOM AIR FAN

WhenstartingyourstovetheRoomAirFanwillnotcomeonuntilthestove’sheatexchangerwarmsup.This

usuallytakesabout10minutesfromstart-up.

IF STOVE RUNS OUT OF PELLETS

Theregoesoutandtheaugermotorandblowerswillrununtilthestovecools.Thiswilltake30minutesorlonger

depending on the heat remaining in the appliance. After the stove components stop running all lights on the

displaywillgooutandthetwodigitdisplaywillbeginashing“E3”

REFUELLING

• Thehopperandstovetopwillbehotduringoperation;therefore,youshouldalwaysusesometypeofhand

protection when refuelling your stove.

• Neverplaceyourhandneartheaugerwhilethestoveisinoperation.Werecommendthatyounotletthe

hopper drop below ¼ full.

TAMPER WARNING

This wood heater has a manufacturer-set minimum low burn rate that must not be altered. It is against federal

regulations to alter this setting or otherwise operate this wood heater in a manner inconsistent with operating

instructions in this manual.

KEEP HOPPER LID CLOSED AT ALL TIMES EXCEPT WHEN REFILLING. DO NOT OVERFILL HOPPER.

-14-

• Failuretocleanandmaintainthisunitasindicatedcanresultinpoorperformance,safetyhazards,re,and

even death.

• Unplugyourstove’selectricalcordpriortoremovingthebackpaneloropeningtheexhaustsystemforany

inspection, cleaning, or maintenance work.

• Never perform any inspections, cleaning, or maintenance on a hot stove.

• Donotoperatestovewithbrokenglass,leakageofuegasmayresult.

EXHAUST SYSTEM

CreosoteFormation–Whenanywoodisburnedslowly,itproducestarandotherorganicvapors,whichcombine

withexpelledmoisturetoformcreosote.Thecreosotevaporscondenseintherelativelycoolchimneyueora

newlystartedreorfromaslow-burningre.Asaresult,creosoteresidueaccumulatesontheuelining.When

ignited,thiscreosotemakesanextremelyhotre,whichmaydamagethechimneyorevendestroythehouse.

Despitetheirhighefciency,pelletstovescanaccumulatecreosoteundercertainconditions.

FlyAsh–Thisaccumulatesinthehorizontalportionofanexhaustrun.Thoughnon-combustible,itmayimpede

thenormalexhaustow.Itshouldthereforebeperiodicallyremoved.

InspectionandRemoval–Thechimneyconnectorandchimneyshouldbeinspectedbyaqualied person

annuallyorpertonofpelletstodetermineifacreosoteoryashbuild-uphasoccurred.Ifcreosotehasaccumulated,

itshouldberemovedtoreducetheriskofachimneyre.Inspectthesystematthestoveconnectionandatthe

chimney top. Cooler surfaces tend to build creosote deposits quicker, so it is important to check the chimney

fromthetopaswellasfromthebottom.Thecreosoteshouldberemovedwithabrushspecicallydesignedfor

thetypeofchimneyinuse.Aqualiedchimneysweepcanperformthisservice.Itisalsorecommendedthat

before each heating season the entire system be professionally inspected, cleaned and, if necessary, repaired.

To clean the chimney, disconnect the vent from the stove.

Operation / Maintenance

SHUTDOWN PROCEDURE

Turningyourstoveoffisamatterofpressingthe“POWER”buttononthedisplayboard.Thegreenlightwillturn

backtoredwhenthe“POWER”buttonispushed.Theaugermotorwillstop,andtheblowerswillcontinueto

operateuntiltheinternalreboxtemperatureshavefallentoapresetlevel.

1. Your stove is equipped with a high temperature thermodisc. This unit has a manual reset thermodisc. This

safety switch has two functions.

A. To recognize an overheat situation in the stove and shut down the fuel feed or auger system.

B. In case of a malfunctioning convection blower, the high-temperature thermodisc will automatically shut

down the auger, preventing the stove from overheating.

NOTE:Onsomeunits,oncetripped,likeacircuitbreaker,theresetbuttonwillhavetobepushedbeforerestarting

yourstove.Onotherunitsthethermodischasnoresetbuttonandwillresetitselfoncethestovehascooled.The

manufacturer recommends that you call your dealer if this occurs as this may indicate a more serious problem.

A service call may be required.

2. If the combustion blower fails, an air pressure switch will automatically shut down the auger.

NOTE:Openingthestovedoorformorethan30secondsduringoperationwillcauseenoughpressurechangeto

activatetheairswitch,shuttingthefuelfeedoff.Thestovewillshutdownandshow“E2”onthetwodigitdisplay.

The stove has to fully shut down before restarting.

WARNING:Nevershutdownthisunitbyunpluggingitfromthepowersource.

-15-

INTERIOR CHAMBERS

• BurnPot:Periodicallyremoveandcleantheburnpotandtheareainsidethe

burn pot housing. In particular, it is advisable to clean out the holes in the burn

pot to remove any build up that may prevent air from moving through the

burn pot freely.

• HeatExchanger:Thereisacleanoutplateonbothsidesoftheheat

exchangerthatneedtoberemovedtocleanyashoutoftheheat

exchanger.Thecleanoutsarelocatedinsidethecabinetdoors,onthelower

frontcornersoftheheatexchanger.Toaccessthesecleanouts,youmust

removebothsidepanels.Thecleanoutsaresecuredtothereboxwith(2)

5/16”screws.Removethecleanoutsandvacuumoutanyaccumulated

ash. This should be done at least once per month or more frequently if large

amounts of ash are noticed while cleaning or if the stove does not seem to be

burning properly.

If a vacuum is used to clean your stove, we suggest using a vacuum designed

forashremoval.someregularvacuumcleaner(i.e.shopvacs)mayleakashinto

the room.

DONOTVACUUMHOTASH

ASH DISPOSAL

Remove ashes when unit has cooled. Ashes should be placed in a metal

containerwithatightttinglid.Theclosedcontainerofashesshouldbeplacedonanoncombustibleooror

ontheground,wellawayfromallcombustiblematerials,pendingnaldisposal.Iftheashesaredisposedofby

burial in soil or otherwise locally dispersed, they should be retained in the closed container until all embers have

been thoroughly cooled. The container shall not be used for other trash or waste disposal. If combined with

combustible substances, ashes and embers may ignite.

SMOKE AND CO MONITORS

Burningwoodnaturallyproducessmokeandcarbonmonoxide(CO)emissions.COisapoisonousgaswhen

exposed to elevatedconcentrations forextended periodsof time.While the modern combustion systemsin

heatersdrasticallyreducetheamountofCOemittedoutthechimney,exposuretothegasesinclosedorconned

areascanbedangerous.Makesureyoustovegasketsandchimneyjointsareingoodworkingorderandsealing

properlytoensureunintendedexposure.ItisrecommendedthatyouusebothsmokeandCOmonitorsinareas

havingthepotentialtogenerateCO.

CHECK AND CLEAN THE HOPPER

Checkthehopperperiodicallytodetermineifthereisanysawdust(nes)thatisbuildingupinthefeedsystem

or pellets that are sticking to the hopper surface. Clean as needed.

DOOR AND GLASS GASKETS

Inspect the main door and glass window gaskets periodically. The main door may need to be removed to have

frayed,broken,orcompactedgasketsreplacedbyyourauthorizeddealer.Thisunit’sdoorusesa5/8”diameter

rope gasket.

BLOWER MOTORS

Cleantheairholesonthemotorsofboththeexhaustanddistributionblowersannually.Removetheexhaust

blowerfromtheexhaustductandcleanouttheinternalfanbladesaspartofyourfallstart-up.Ifyouhaveindoor

pets your power motors should be inspected monthly to make sure they are free of animal hair build up. Animal

hair build up in blowers can result in poor performance or unforeseen safety hazards.

PAINTED SURFACES

Painted surfaces may be wiped down with a damp cloth. If scratches appear, or you wish to renew your paint,

contact your authorized dealer to obtain a can of suitable high-temperature paint.

GLASS - CLEANING, REMOVAL AND REPLACEMENT OF BROKEN DOOR GLASS

Cleaning-Werecommendusingahighqualityglasscleaner.Shouldabuildupofcreosoteorcarbonaccumulate,

youmaywishtouse000steelwoolandwatertocleantheglass.DONOTuseabrasivecleaners.DONOTperform

thecleaningwhiletheglassisHOT.,

Maintenance

-16-

Intheeventyouneedtoreplacetheglass,removethefour(4)screwsandglassretainers.Whilewearingleather

gloves(oranyotherglovessuitableforhandlingbrokenglass),carefullyremoveanyloosepiecesofglassfrom

thedoorframe.Disposeofallbrokenglassproperly.ONLYhightemperatureceramicglassofthecorrectsizeand

thicknessmaybeused.DONOTsubstitutealternativematerialsfortheglass.Contactyourauthorizeddealerto

obtain this glass. Re-install the new glass by re-attaching the retainers and screws, be careful not to over tighten

the screws for this could damage the glass.

DONOTabusethedoorglassbystriking,slammingorsimilartrauma.Donotoperatethestovewiththeglass

removed, cracked or broken.

FALL START UP

Priortostartingtherstreoftheheatingseason,checktheoutsideareaaroundtheexhaustandairintake

systemsforobstructions.Cleanandremoveanyyashfromtheexhaustventingsystem.Cleananyscreenson

theexhaustsystemandontheoutsideairintakepipe.Turnallofthecontrolsonandmakesurethattheyare

working properly. This is also a good time to give the entire stove a good cleaning throughout.

SPRING SHUTDOWN

After the last burn in the spring, remove any remaining pellets from the hopper and the auger feed system.

Scoopoutthepelletsandthenruntheaugeruntilthehopperisemptyandpelletsstopowing(thiscanbedone

bypressingthe“ON”buttonwiththeviewingdooropen).Vacuumoutthehopper.Thoroughlycleantheburn

pot,andrebox.Itmaybedesirabletospraytheinsideofthecleanedhopperwithanaerosolsiliconesprayif

yourstoveisinahighhumidityarea.Theexhaustsystemshouldbethoroughlycleaned.

Spring shutdown

After the last burn in the spring, remove any remaining pellets from the hopper and the auger feed system.

Scoopoutthepelletsandthenruntheaugeruntilthehopperisemptyandpelletsstopowing(thiscanbedone

bypressingthe“ON”buttonwiththeviewingdooropen).Vacuumoutthehopper.Thoroughlycleantheburn

pot,andrebox.Itmaybedesirabletospraytheinsideofthecleanedhopperwithanaerosolsiliconesprayif

yourstoveisinahighhumidityarea.Theexhaustsystemshouldbethoroughlycleaned.

MAINTENANCE SCHEDULE

Use the following as a guide under average use conditions.

Gaskets around door and door glass should be inspected and repaired or replaced when necessary.

Daily Weekly Monthlyorasneeded

BurnPot Stirred Empty

Combustion Chamber Brushed

Ashes Check Empty

Interior Chambers Vacuumed

CombustionBlowerBlades Vacuumed/Brushed

ConvectionBlowerImpeller Vacuumed/Brushed

Vent System Cleaned

Gaskets Inspected

Glass Wiped Cleaned

Hopper(endofseason) Emptyandvacuumed

Maintenance

-17-

Whenyourstoveactsoutoftheordinary,therstreactionistocallforhelp.Thisguidemaysavetimeandmoney

byenablingyoutosolvesimpleproblemsyourself.Problemsencounteredareoftentheresultofonlyvefactors:

1)poorfuel;2)pooroperationormaintenance;3)poorinstallation;4)componentfailure;5)factorydefect.You

canusuallysolvethoseproblemsrelatedto1and2.Yourdealercansolveproblemsrelatingto3,4and5.Refer

to diagrams on page 25 to help locate indicated parts.

For the sake of troubleshooting and using this guide to assist you, you should look at your heat level setting to

seewhichlightisashing.

• Disconnectthepowercordbeforeperforminganymaintenance!NOTE:TurningtheON/OFFSwitchto”OFF”

does not disconnect all power to the electrical components of the stove.

• Never try to repair or replace any part of the stove unless instructions for doing so are given in this manual.

All other work should be done by a trained technician.

ATTENTION:Thiswoodheaterneedsperiodicinspectionandrepairforproperoperation.Itisagainstfederal

regulations to operate this wood heater in a manner inconsistent with operating instructions in this manual.

Trouble Shooting Guide

DisplayisFlashing“E1”

Possible Causes PossibleRemedies:(Unplugstoverstwhenpossible)

1. The convection blower is overheating and

tripping the internal temperature shutoff.

Clean any dust off of the windings and fan blade. If oiling the

blower does not help, the blower may be bad.

2. The stove is being left on the highest setting for

extendedperiodsoftime.

If operating the heater on the highest heat setting, the room

temperature could increase enough and lead to potential

overheating situations. If this happens try operating at a lower

heat setting.

3. Fuel other than wood pellets is being burned in

the stove.

This pellet stove is designed and tested to use wood pellets.

Check for signs of fuel other than wood pellets. No other types of

fuel have been approved for this pellet stove. If there are signs of

other types of fuel being used, stop using them immediately.

4. Power surge or brown out situation.

A power surge, spike, or voltage drop could cause the high limit

switch to trip. Check to see if a surge protector is being used on

the stove. If not, recommend one to the customer.

5. HighLimitSwitchismalfunctioning. IftheotheritemscheckoutOK,replacethehighlimitswitch.

-18-

Trouble Shooting Guide

DisplayisFlashing“E2”

Possible Causes PossibleRemedies:(Unplugstoverstwhenpossible)

1. Airowswitchhoseorstoveattachmentpipesfor

hose are blocked.

Unhook air hose from the air switch and blow through it. If air

owsfreely,thehoseandtubearene.Ifairwillnotowthrow

the hose, use a wire coat hanger to clear the blockage.

2. The air inlet, burnpot, interior combustion air

chambers,combustionblower,orexhaustpipe

are blocked with ash or foreign material.

Follow all cleaning procedures in the maintenance section of the

owner’smanual.

3. Thereboxisnotproperlysealed.

Makesurethedoorisclosedandthatthegasketisingood

shape.

4. Vent pipe is incorrectly installed.

Check to make sure vent pipe installation meets criteria in

owner’smanual.

5. Theairowswitchwireconnectionsarebad.

Check the connectors that attach the gray wires to the air

switch.

6. Combustion blower failure.

Withthestoveon,checktoseeifthecombustionbloweris

running. If it is not, you will need to check for power going to the

combustion blower. It should be a full current. If there is power,

the blower is bad. If there is not, see #8.

7. Control board not sending power to combustion

blower.

If there is no current going to the combustion blower, check all

wire connections. If all wires are properly connected, you have a

bad control board.

8. Control board not sending power to air switch.

Thereshouldbea5-voltcurrent(approximately)goingtotheair

switch after the stove has been on for 30 seconds.

9. Air switch has failed.

To test the air switch, you will need to disconnect the air hose

fromthebodyofthestove.Withtheotherendstillattached

to the air switch, very gently suck on the loose end of the hose

(youmaywanttoremovethehoseentirelyoffthestoveand

theairswitchrstandmakesureitisclear).Ifyouhearaclick,

theairswitchisworking.BECAREFULTOOMUCHVACUUMCAN

DAMAGETHEAIRSWITCH.

-19-

Trouble Shooting Guide

DisplayisFlashing“E3”

Possible Causes PossibleRemedies:(Unplugstoverstwhenpossible)

1. The hopper is out of pellets Rellthehopper.

2. The air dampener is too far open for a low feed

setting

If on the low setting, you may need to close the dampener all the

way.

3. The burnpot holes are blocked. Remove the burnpot and thoroughly clean it.

4. Theairinlet,theinteriorchambers,orexhaust

system has a partial blockage.

Follow all cleaning procedures in the maintenance section of the

owner's manual

5. The hopper safety switch has failed or hopper

is open.

Whenoperatingtheunit,besurethehopperlidisclosedsothat

the hopper safety switch will activate. Check the wires leading

from the hopper safety switch to the control panel and auger

motor for secure connections. Use a continuity tester to test the

hoppersafetyswitch;replaceifnecessary.

6. The auger shaft is jammed.

"Start by emptying the hopper. Then remove the auger motor by

removing the auger pin, then remove the two bolts that hold the

auger bracket to the auger tube. The auger bracket will now be

able to be removed form the auger tube. Remove the two bolts

on the side of the auger tube to remove the lower bearing of the

auger. Pull the auger out of the tube to free the jam.

7. The auger motor has failed.

Remove the auger motor from the auger shaft and try to run the

unit. If the motor will turn the shaft is jammed on something. If the

motor will not turn, the motor is bad.

8. TheProofofFire(POF)thermodischas

malfunctioned.

TemporarilybypassthePOFthermodiscbydisconnectingthetwo

wires and connecting them with a short piece of wire. Then plug

the stove back up. If the stove comes on and works, you need to

replacethePOFthermodisc.Thisisfortestingonly.DONOTLEAVE

THETHERMODISCBYPASSED.Yourblowerswillnevershutoffand

iftherewentouttheaugerwillcontinuetofeedpelletsuntilthe

hopperisemptyifyouleavethePOFthermodiscbypassed.

9. The control board is not sending power to

thePOFthermodiscorotheraugersystem

components.

Thereshouldbea5-volt(approximately)currentgoingtothePOF

thermodiscafterthestovehasbeenonfor10minutes.

-20-

Trouble Shooting Guide

DisplayisFlashing“E4”

Possible Causes PossibleRemedies:(Unplugstoverstwhenpossible)

1. The air inlet, burnpot, interior combustion air

chambers,combustionblower,orexhaustpipeare

blocked with ash or foreign material.

Follow all cleaning procedures in the maintenance section of

theowner’smanual.

2. TheProofofFire(POF)thermodischascame

unplugged

Checkthe(POF)thermodisctoseeifthewiresareconnected

properly.

3. TheProofofFire(POF)thermodischas

malfunctioned.

TemporarilybypassthePOFthermodiscbydisconnectingthe

two wires and connecting them with a short piece of wire.

Then plug the stove back up. If the stove comes on and works,

youneedtoreplacethePOFthermodisc.Thisisfortestingonly.

DONOTLEAVETHETHERMODISCBYPASSED.Yourblowerswill

nevershutoffandiftherewentouttheaugerwillcontinue

tofeedpelletsuntilthehopperisemptyifyouleavethePOF

thermodisc bypassed.

4. The hopper is out of Pellets. Rellthehopper.

5. The hopper safety switch has failed or hopper is

open.

Whenoperatingtheunit,besurethehopperlidisclosedso

that the hopper safety switch will activate. Check the wires

leading from the hopper safety switch to the control panel

and auger motor for secure connections. Use a continuity

testertotestthehoppersafetyswitch;replaceifnecessary.

6. The auger shaft is jammed.

Start by emptying the hopper. Then remove the auger

motor by removing the auger pin. Remove the auger shaft

inspection plate in the hopper so that you can see the auger

shaft. Gently lift the auger shaft straight up so that the end of

the auger shaft comes up out of the bottom auger bushing.

Next,removethetwonutsthatholdthetopaugerbiscuitin.

Then rotate the bottom end of the auger shaft up towards

you until you can lift the shaft out of the stove. After you have

removedtheshaft,inspectitforbentights,burrs,orbroken

welds. Remove any foreign material that might have caused

the jam. Also, check the auger tube for signs of damage such

as burrs, rough spots, or grooves cut into the metal that could

have caused a jam.

7. The auger motor has failed.

Remove the auger motor from the auger shaft and try to

run the unit. If the motor will turn the shaft is jammed on

something. If the motor will not turn, the motor is bad.

DisplayisFlashing“E5”

Possible Causes PossibleRemedies:(Unplugstoverstwhenpossible)

1. Thestoveautomaticallyashes"E5"whenturnedon

The T-stat sensor has come unplugged form the control board.

Check to see if the sensor is unplugged. If the sensor is not

unplugged then the sensor is damaged or has a short. If the

sensor is damaged or has a short it will need to be replaced.

La page charge ...

Ashley Hearth Products VG5790 Manuel utilisateur

Marque: Ashley Hearth Products

Modèle: VG5790

Catégorie: Poêles

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Ashley Hearth Products VG5790 User manual

Ashley Hearth Products VG5790 Manuel utilisateur

Ce manuel convient également à

Ashley Hearth Products VG5790 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents