Raven Slingshot Guide d'installation

Manual de instalación

Руководство по

установке

Slingshot™ Base Station

Manual de Instalação

Le manuel d'installation

Installation Manual

TM

Raven Industries will not assume any expense or liability for repairs

made outside our facilities without written consent. Raven Industries

is not responsible for damage to any associated equipment or

products and will not be liable for loss of profit or other special

damages. The obligation of this warranty is in lieu of all other

warranties, expressed or implied, and no person or organization is

authorized to assume any liability for Raven Industries.

Damages caused by normal wear and tear, misuse, abuse, neglect,

accident, or improper installation and maintenance are not covered

by this warranty.

What Does this Warranty Cover?

How Long is the Coverage Period?

How Can I Get Service?

What Will Raven Industries Do?

What is not Covered by this Warranty?

Bring the defective part and proof of purchase to your Raven dealer.

If your dealer agrees with the warranty claim, the dealer will send the

part and proof of purchase to their distributor or to Raven Industries

for final approval.

Upon confirmation of the warranty claim, Raven Industries will, at our

discretion, repair or replace the defective part and pay for return

freight.

RAVEN INDUSTRIES

Limited Warranty

This warranty covers all defects in workmanship or materials in your

Raven Applied Technology Division product under normal use,

maintenance, and service.

Raven Applied Technology Division products are covered by this

warranty for 12 months after the date of purchase. This warranty

coverage applies only to the original owner and is nontransferable.

Stipulation d'exonération

Bien que tous les efforts ont été faits pour s'assurer de l'exactitude de ce document,

Raven Industries n'assume aucune responsabilité pour les omissions et les erreurs.

Elle n'est pas non plus responsable quant aux dommages résultant de l'utilisation des

informations contenues dans ce document.

Raven Industries ne peut être tenue responsable des dommages directs ou indirects

ou d'une perte de bénéfices ou de profits, arrêt de travail ou de la perte ou la

détérioration des données découlant de l'utilisation ou l'incapacité à utiliser, ce

système ou un de ses composants. Raven Industries ne saurait être tenue

responsable des modifications ou des réparations faites à l'extérieur de nos

installations, ni des dommages résultant d'une mauvaise maintenance de ce système.

Comme avec tous les signaux sans fil et par satellite, plusieurs facteurs peuvent

affecter la disponibilité et la précision de la navigation sans fil et par satellite et des

services de correction (e.g. GPS, GNSS, SBAS, etc.). Par conséquent, Raven

Industries ne peut pas garantir l'exactitude, l'intégrité, la continuité ou la disponibilité

de ces services et ne peut garantir la possibilité d'utiliser les systèmes de Raven, ou

les produits utilisés comme composants de systèmes, qui reposent sur la réception de

ces signaux ou la disponibilité de ces services. Raven Industries décline toute

responsabilité pour l'utilisation de l'un de ces signaux ou de ces services pour d'autres

fins que celles indiquées.

Embora tenham sido empregados todos os esforços para assegurar a precisão

deste documento, a Raven Industries não assume nenhuma responsabilidade

por omissões e erros. E nenhuma responsabilidade é assumida por danos

resultantes da utilização das informações aqui contidas.

A Raven Industries não se responsabiliza por danos incidentais ou

consequenciais ou pela perda de benefícios ou lucros antecipados, parada ou

perda de trabalhos, ou pela destruição de dados resultantes da utilização, ou

incapacidade de utilização deste sistema ou de seus componentes. A Raven

Industries não se responsabilizará por quaisquer modificações ou reparos

realizados fora de nossas instalações, nem por danos resultantes da

inadequada manutenção deste sistema.

Assim como com todos os sinais sem fio e de satélite, vários fatores podem

afetar a disponibilidade e a exatidão da navegação sem fio e a satélite e de

serviços de correção (tais como GPS, GNSS, SBAS, etc.). Portanto, a Raven

Indusries não pode garantir a precisão, integridade, continuidade, ou

disponibiidade destes serviços, e não pode garantir a capacidade de se utilizar

os sistemas Raven, ou dos produtos utilizados como componentes de sistemas,

que dependem da recepção destes sinais ou da disponibilidade destes serviços.

A Raven Industries não aceita responsabilidade pelo uso de quaisquer destes

sinais ou serviços para fins fora do objetivo declarado.

Isenção de Responsabilidade

Si bien se ha realizado todo esfuerzo posible para asegurar la precisión del

contenido de este documento, Raven no se responsabiliza por omisiones

o errores. Tampoco se responsabiliza por los daños que ocasione el uso de la

información aquí consignada.

Tampoco es responsable de los daños incidentales o consecuentes, pérdida de

beneficios o ganancias anticipados, interrupción o pérdida de trabajo, ni de los

daños ocasionados a información que resulten del uso, o imposibilidad de

utilizar, el presente sistema o alguno de sus componentes. Raven Industries no

es responsable de las reparaciones o modificaciones que se realicen fuera de

sus instalaciones ni de los daños que resulten de un mantenimiento inadecuado

del sistema.

Es común en toda señal inalámbrica y satelital que la disponibilidad y la

precisión de la navegación inalámbrica y satelital y sus servicios de corrección

se vean afectados por varios factores (p. ej. GPS, GNSS, SBAS, etc.). Por ello,

Raven Industries no garantiza la precisión, integridad, continuidad

o disponibilidad de estos servicios. Tampoco garantiza el funcionamiento de los

sistemas Raven, o de sus productos con otros sistemas, que dependan de la

recepción de este tipo de señales o de la disponibilidad de estos servicios.

Raven Industries se exime de toda responsabilidad que resulte del uso de estas

señales o servicios para perseguir fines diferentes a los previstos.

Exención de responsabilidad

Хотя были приложены максимальные усилия для обеспечения точности

информации, приведенной в данном документе, компания Raven Industries

не несет ответственности за возможные ошибки и упущения. Помимо этого,

компания не несет ответственности за ущерб, причиненный в результате

использования содержащейся в данном документе информации.

Компания Raven Industries не несет ответственности за случайные или

закономерные повреждения, за упущенную выгоду, простои в работе,

потерю или повреждение данных, возникшие вследствие использования

или невозможности использования данной системы и любых ее

компонентов. Компания Raven Industries не несет ответственности за любые

модификации или ремонт, произведенный не на наших производственных

мощностях, а также за ущерб, вызванный ненадлежащим обслуживанием

системы.

Как и в случае беспроводных и спутниковых сигналов, доступность

и точность навигации по беспроводному соединению и спутниковым

сигналам, а также доступность и точность услуг корректировки (т. е. GPS,

ГНСС, SBAS и т. п.) зависят от ряда факторов. Поэтому компания Raven

Industries не может гарантировать точность, целостность, непрерывность

и доступность этих услуг, а также не может гарантировать возможность

использования систем Raven или изделий, используемых в качестве

компонентов систем, работа которых основана на приеме этих сигналов или

доступности этих услуг. Компания Raven Industries не несет ответственности

за последствия использования этих сигналов и услуг в целях, отличных от

перечисленных в данном документе.

Ограничение ответственности

Table of Contents

Manual No. 016-0171-408 i

Chapter 1 Important Safety Information ............................................ 1

FCC Statement: .......................................................................................................1

Chapter 2 Introduction & Preparation................................................ 3

Introduction ..............................................................................................................3

Preparation for Base Station Delivery ......................................................................3

Broadband Internet Installation ....................................................................4

Uninterruptible Power Supply (UPS) Set Up ...............................................4

Base Station Antenna Installation ................................................................5

Chapter 3 Base Station Installation & Start Up ................................. 7

Base Station Connections .......................................................................................7

Start Up ....................................................................................................................9

Fixing the Base Station Location ...........................................................................10

Chapter 4 Informations importantes relatives à la sécurité........... 11

Directive FCC : ...................................................................................................... 11

Chapitre 5 Introduction et Préparation ............................................. 13

Introduction ............................................................................................................13

Préparation de la Station de Base .........................................................................13

Installation de la Connexion Internet à Haut Débit ....................................14

Alimentation Stabilisée et de Secours .......................................................14

Installation de l'antenne .............................................................................15

Chapitre 6 Installation et démarrage de la station de base............. 19

Installation et démarrage .......................................................................................19

Démarrage .............................................................................................................21

Contrôle de la Position de la Station de Base .......................................................22

Capítulo 7 Informações importantes sobre segurança................... 23

Declaração da FCC: ..............................................................................................23

Capítulo 8 Introdução e Preparação ................................................. 25

Introdução ..............................................................................................................25

Preparação da estação base .................................................................................25

Instalação de Internet Banda Larga ...........................................................26

Configuração da fonte de alimentação ininterrupta (UPS) ........................26

Instalação da antena da estação base Slingshot ......................................27

Table of Contents

ii Slingshot™ Base Station Installation Manual

Capítulo 9 Instalação e inicialização da estação base.................... 31

Instalação e Inicialização .......................................................................................31

Inicialização ...........................................................................................................33

Fixiando o Local da Estação Base ........................................................................34

Chapter 10 Información de seguridad importante............................ 35

Declaración de la Comisión Federal de Comunicaciones (FCC, por sus siglas en

inglés): ...................................................................................................................35

Chapter 11 Introducción y preparación............................................. 37

Introducción ...........................................................................................................37

Previo a la entrega de la base de comando ..........................................................37

Conexión a Internet de banda ancha .........................................................38

Instalación del sistema UPS ......................................................................38

Instalación de la antena de la base de comando .......................................39

Chapter 12 Instalación y operación de la base de comando........... 41

Conexiones de la base de comando .....................................................................41

Operación ..............................................................................................................43

Fijación de la ubicación de la base de comando ...................................................44

Глава 13 Важные инструкции по технике безопасности..... 45

Заявление о соответствии требованиям FCC: ..................................................45

Chapter 14 Введение и предварительная подготовка.............. 47

Введение ..............................................................................................................47

Подготовка к установке базовой станции ...........................................................47

Широкополосное подключение к Интернету ..........................................48

Установка источника бесперебойного питания (ИБП) ...........................48

Установка антенны базовой станции ......................................................50

Chapter 15 Установка и запуск базовой станции....................... 53

Подключение базовой станции ...........................................................................53

Запуск ...................................................................................................................55

Фиксация местоположения базовой станции ....................................................56

CHAPTER

1

Manual No. 016-0171-408 1

English

C hapter 1

Important Safety

Information

Read this manual and the safety information provided within before installing the Slingshot™ base station.

• Follow all safety information presented within this manual.

• Be sure to review local building codes prior to erecting or modifying any structure for mounting the base

station antenna. Contact a professional electrician for more information.

• If you require assistance with any portion of the installation, contact the Raven Network Operations Center

for support.

FCC Statement:

This device complies with Part 15 of FCC rules. Operation of this device is subject to the following two

conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired

operation.

This equipment generates, uses and may radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected

• Consult the dealer or an experienced radio or television technician for help

NOTICE

Chapter 1

2 Slingshot™ Base Station Installation Manual

•

Only personnel qualified to work on raised platforms or trained to use fall protection equipment should

install or perform maintenance on the base station antenna.

• Be sure to follow all safety guidelines when working on raised platforms or elevation. Contact a qualified

training facility for additional information.

• Raven Industries does not supply lightning arresting equipment. Refer to local building and electrical codes

and contact a professional electrician for more information regarding lightning arresting equipment.

• Make sure the entry point into any building or structure is properly sealed to prevent moisture from

migrating into the building and causing damage to the Slingshot base station or other property.

• Ensure that the power cable is the last cable to be connected.

WARNING

CAUTION

CHAPTER

2

Manual No. 016-0171-408 3

English

C hapter 2

Introduction &

Preparation

Introduction

The Slingshot™ base station is designed to provide subscribed field hubs with RTK level GNSS (Global

Navigation Satellite System) corrections via a cellular service provider. Correction information is sent from the

Slingshot base station to the Raven Slingshot server and back to a field hub to supply the guidance correction

information to the guidance device.

The Slingshot base station will be delivered and installed in two phases:

1. Preparation and set up for a new base station.

2. Delivery and commissioning of the Slingshot base station.

Review and complete the instructions in this chapter prior to delivery of the Slingshot base station.

Preparation for Base Station Delivery

The following items are required before the Raven Slingshot base station may be set up:

• A dedicated, broadband internet connection (DSL, cable, etc.) with a public IP address and DHCP support.

• A dry, temperature controlled environment suitable for computer equipment with a connection to a

dedicated internet line and adequate power receptacles.

Note: The base station tray is compatible with a 2U 19” [48 cm] server rack for optional mounting.

• An uninterruptible power supply (UPS) installed per instructions provided with the device.

• A location within reach of the base station antenna mounting location and cable (maximum cable length

200’ [60 m]).

To ensure the most efficient installation, complete the following items prior to receiving the Raven Slingshot

base station:

Chapter 2

4 Slingshot™ Base Station Installation Manual

Broadband Internet Installation

Contact a local internet service provider to have a dedicated, broadband internet connection installed. The

internet connection must be always on and available via an unblocked, public IP address. Dial up

connections and connections with a built-in router are not supported.

Uninterruptible Power Supply (UPS) Set Up

Set up the provided uninterruptible power supply, or UPS, as described in the instruction sheet provided with

the device. The UPS should be set up in the location where the base station will be located when delivered.

Note: Review the instructions provided by the UPS manufacturer prior to connecting any equipment to

the device.

1. Connect the internet modem directly to the ethernet surge protection port labeled ‘IN.’

2. Using an ethernet cable, connect the ethernet surge protection port labeled ‘OUT’ to the Slingshot base

station ethernet port (to be connected when base station is delivered).

3. Using a second ethernet cable, connect the ethernet port in the UPS accessory slot to the UPS

management port on the Slingshot base station (to be connected when the base station is delivered).

FIGURE 1. UPS Battery Backup Connections

4. Refer to the instructions provided with the UPS device to properly set the Voltage Dip Switch.

5. Connect the UPS to a power source as described in the manufacturer’s instructions.

Note: A region specific power adapter cable is supplied with the 220 V UPS as part of the Slingshot

system.

Battery Backup Outlets

Ethernet Surge

Protection

UPS Management

Port

Voltage Dip

Switches

110 V UPS 220 V UPS

Manual No. 016-0171-408 5

Introduction & Preparation

English

Base Station Antenna Installation

Before mounting the Slingshot base station antenna, select a site which meets the following conditions to

ensure optimal performance:

• Ensure the antenna location provides a clear, 360° view of the sky.

• Antenna should be mounted as far from reflective objects (i.e. metal buildings, water bodies) as possible

and should be higher than surrounding obstructions (i.e. tree lines, power lines, etc.).

• If obstructions or reflective surfaces are within 100’ [30 m], mount the Slingshot base station as high as

possible to minimize interference and/or multipath reflections. If no obstructions or reflective surfaces are

within this range, mount the antenna as low as possible.

• Use a sturdy mounting bracket with a 5/8” -11 NC thread. The thread must be between 3/8” to 7/8” [9.6 mm

to 22 mm] long to ensure proper mounting and avoid damage to the antenna casing. If the thread length is

longer than 7/8” [22 mm], use two jam nuts to shorten the exposed thread.

FIGURE 2. Example Antenna Mounting with Jam Nuts

• The antenna mount should provide a solid base for the antenna and should not allow the antenna to move

in any direction.

• Mount the antenna with the thread adapter and TNC cable connector facing toward the ground.

• Make sure the entry point into any building or structure is properly sealed to prevent moisture from

migrating into the building and causing damage to the Slingshot base station or other property. Use a drip

loop to keep moisture away from the entry point.

Note: It is recommended to contact a qualified electrician to route the cable into the building.

FIGURE 3. Drip Loop Example

Chapter 2

6 Slingshot™ Base Station Installation Manual

•

To prevent damaging the antenna cable, do not route cables through potential crimp points such as doors or

windows. Avoid severe bends in the cable as this may also cause damage to the cable.

TABLE 1. LMR 400 Antenna Cable Bending Specifications

Base Station Antenna Mounting

To install the Slingshot base station antenna:

1. Verify that the thread on the antenna mount does not extend more than 7/8” [22 mm] to ensure the plastic

inside the antenna receptacle is not damaged when the mount is inserted. If the thread length is longer than

7/8” [22 mm], use two jam nuts to shorten the exposed thread.

2. Thread the metal adapter on the bottom of the antenna onto the mount.

Note: The metal adapter is fixed to the antenna body. Do not attempt to remove this piece.

3. Using a wrench, tighten the antenna adapter to the mount to secure the base station antenna.

4. Remove the dust cap from the TNC connector on the antenna.

5. Attach one end of the provided base station antenna cable to the antenna and route to the selected base

station location.

Note: If the antenna will be mounted on a tower structure, be sure to leave enough slack in the antenna

cable to allow for expansion and contraction of the structure to avoid damaging the cable. Raven

recommends contacting a certified electrician to assist with cable installation and routing.

If the antenna cable will be routed into a building, be sure to use a drip loop to prevent moisture

from entering the building by wicking along the cable. Also be sure to seal any building

penetrations properly to prevent moisture and condensation.

Care & Maintenance

The base station antenna is designed to withstand the elements, including rain, snow, and dust. To ensure that

the antenna continues to perform as desired, keep the radome (top surface of the antenna) clear of snow and

ice and clear any debris as necessary.

Ensure that the TNC antenna cable connector remains clean and dry. If the cable will be disconnected from the

antenna for any length of time, replace the dust cap on the antenna.

Specification Units

Bend Radius (Installation) 1.0 in [25.4 mm]

Bend Radius (Repeated) 4.0 in [101.6 mm]

Bending Moment 0.5 ft.-lb. [0.68 N-m]

CHAPTER

3

Manual No. 016-0171-408 7

English

C hapter 3

Base Station

Installation & Start Up

Contact your regional Raven Sales or Precision Agriculture Specialist to coordinate installation and set up of

the Slingshot™ base station.

Note: Be sure that all required items outlined in Chapter 2, Introduction & Preparation, have been

completed prior to installing the base station.

The following sections contain instructions for installation and start up of the base station for reference during

the installation and set up of the base station.

Base Station Connections

1. Setup the Slingshot base station unit in the prepared location.

Note: The base station tray is compatible with a 2U 19” [48 cm] server rack for optional mounting.

FIGURE 1. Base Station Connectors

2. Connect the base station antenna cable to the TNC connector on the base station.

3. Connect the cable from the surge protected ethernet ‘OUT’ port on the back of the UPS to the ethernet port

on the base station.

Ethernet

Port

TNC Antenna

Port

3-Pin Power

Adapter Port

3A Fuse

Ground Power

(+12

VDC)

Keyway

No Connection

UPS

Management Port

Chapter 3

8 Slingshot™ Base Station Installation Manual

4. Connect the UPS management port to the ethernet connection in the accessory slot on the back of the

UPS.

5. Connect the circular, three pin connector on the power adapter cable to the three pin power plug on the

base station.

6. Route the power adapter cable to one of the battery backup plugs on the UPS.

FIGURE 2. UPS Battery Backup Outlets

Battery Backup Outlets

Manual No. 016-0171-408 9

Base Station Installation & Start Up

English

Start Up

1. Check that the UPS is powered on. Review the instructions provided by the UPS manufacturor for details.

2. Press the red power button on the DL-V3 base station receiver within the Slingshot base station to power

up the unit.

FIGURE 3. Slingshot Base Station Power Button

As soon as the Slingshot base station is powered up and receiving GNSS, the base station will begin

convergence to determine the base station location. This process may take up to 15 minutes. Once

complete, the base station is pre-programmed to begin communicating with the Raven Slingshot server and

will begin broadcasting corrections for use by rover units within the coverage area.

3. After the first fifteen minutes, the “AUX” and “COM2” LED indicators should blink once per second if

corrections are being sent to the Raven Slingshot server.

4. Test the UPS Verify that power to the Slingshot base station is not interrupted and the battery backup is

functioning properly.

Note: Refer to the instructions provided with the UPS device to perform a test of the battery backup

functions.

Power LED

Chapter 3

10 Slingshot™ Base Station Installation Manual

Fixing the Base Station Location

After the initial installation and convergence, the Slingshot base station will continue to broadcast corrections to

the Slingshot server in a demonstration mode. This mode is adequate for conducting client demonstrations of

the Slingshot system and will provide RTK level corrections to any subscribers so clients may begin using RTK

guidance from the Slingshot base station immediately.

To provide the best possible corrections over time, the Slingshot base station position should be surveyed and

set to a fixed operation mode. The Raven Network Operations Center will assist with this transition to process

the base station location, fix the position and permanently program the location into the base station.

CHAPITRE

4

Manual No. 016-0171-408 11

Français

C hapter 4

Informations

importantes relatives

à la sécurité

Lisez attentivement ce manuel et les informations de sécurité qu'il contient avant d'installer la station de base

Slingshot™.

• Suivez toutes les consignes de sécurité indiquées dans le présent manuel.

• Assurez-vous d'avoir bien pris connaissance du code du bâtiment local avant de monter ou de modifier une

structure afin d'y installer l'antenne de la station de base. Contactez un électricien professionnel pour en

savoir plus.

• Pour tout besoin d'assistance pour quelque partie que ce soit de l'installation, contactez la Raven Network

Operations Center (NOC - centre opérationnel Raven).

Directive FCC:

Ce dispositif est conforme à l'article 15 des règles FCC. L'utilisation de ce dispositif est soumise aux deux

conditions suivantes :

1. Ce dispositif ne peut pas causer d'interférences nuisibles.

2. Ce dispositif doit accepter toutes les interférences reçues, y compris les interférences qui peuvent causer

un fonctionnement non désiré.

Cet équipement génère, utilise et est susceptible d'émettre des fréquences radio, et, s'il n'est pas installé et

utilisé conformément à ce mode d'emploi, risque de causer des interférences nuisibles aux communications

radio. Cependant, ceci n'est pas une garantie qu'aucune interférence ne se produira dans une installation

particulière. Si cet équipement cause des interférences nuisibles à la réception de la radio ou de la télévision,

qui peuvent être déterminées en activant et en désactivant l'équipement, l'utilisateur est encouragé à tenter de

supprimer les interférences par un ou plusieurs des moyens suivants :

• Réorientez ou déplacez l'antenne de réception.

• Augmentez la séparation entre l'équipement et le récepteur

• Connectez l'équipement à une prise sur un circuit différent de celui auquel est connecté le

récepteur

• Consultez le distributeur ou un technicien radio/TV expérimenté.

REMARQUE

Chapitre 4

12 Slingshot™ Base Station Installation Manual

•

Seules les personnes qualifiées pour travailler sur des plates-formes en hauteur ou entraînées à l'utilisation

des équipements de protection anti-chute sont autorisées à installer ou à réaliser l'entretien de l'antenne de

la station de base.

• Veillez à bien respecter toutes les consignes de sécurité lorsque vous travaillez sur des plateformes

élévatrices ou en hauteur. Contactez un organisme de formation agréé pour en savoir plus.

• Raven Industries ne fournit pas d'équipement anti-foudre. Reportez-vous à la règlementation électrique et

au code du bâtiment locaux et contactez un électricien professionnel pour en savoir plus sur les

équipements anti-foudre.

• Veillez à ce que le point d'entrée à l'intérieur de tout bâtiment ou structure est bien étanche pour empêcher

l'humidité de pénétrer dans le bâtiment et d'endommager la station de base Slingshot ou tout autre

équipement.

• Connectez le câble d'alimentation en dernier.

AVERTISSEMENT

MISE EN GARDE

La page charge ...

Raven Slingshot Guide d'installation

Raven Slingshot Guide d'installation

dans d''autres langues

Autres documents