Sony DVP-S7700 Le manuel du propriétaire

Marque: Sony

Modèle: DVP-S7700

Catégorie: Lecteurs DVD

Taper: Le manuel du propriétaire

3-864-941-12 (1)

CD/DVD Player

 1998 by Sony Corporation

DVP-S7700

Operating Instructions

Mode d'emploi

WARNING

To prevent fire or shock hazard, do not

expose the unit to rain or moisture.

To avoid electrical shock, do not open the

cabinet. Refer servicing to qualified personnel

only.

CAUTION

The use of optical instruments with this product will

increase eye hazard. As the laser beam used in this

CD/DVD Player is harmful to eyes, do not attempt to

disassemble the cabinet.

Refer servicing to qualified personnel only.

This label is located on the Laser protective housing

inside the enclosure.

For customers in the U.S.A.

This symbol is intended to alert the

user to the presence of uninsulated

“dangerous voltage” within the

product’s enclosure that may be of

sufficient magnitude to constitute a

risk of electric shock to persons.

This symbol is intended to alert the

user to the presence of important

operating and maintenance (servicing)

instructions in the literature

accompanying the appliance.

Owner’s Record

The model and serial numbers are located at the rear of

the unit. Record the serial number in the space

provided below. Refer to them whenever you call upon

your Sony dealer regarding this product.

Model No. DVP-S7700

Serial No.______________

CAUTION

You are cautioned that any change or modifications not

expressly approved in this manual could void your

authority to operate this equipment.

NOTE:

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and

receiver.

– Connect the equipment into an outlet on a circuit

different from that to which the receiver is

connected.

– Consult the dealer or an experienced radio/TV

technician for help.

For customers in Canada

CAUTION

TO PREVENT ELECTRIC SHOCK MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Welcome!

Thank you for purchasing the Sony CD/DVD Player. Before

operating the unit, please read this manual thoroughly and

retain it for future reference.

TABLE OF CONTENTS

This Player Can Play the Following Discs ............................................................4

Getting Started

Unpacking..................................................................................................................6

Hooking Up the System...........................................................................................6

Necessary Setup Before Using the Player .............................................................9

Selecting the Language for On-screen Display ....................................................9

Basic Operations

Playing a DVD.........................................................................................................10

Playing a CD/VIDEO CD......................................................................................14

Playing Discs in Various Modes

Using the On-Screen Display ................................................................................18

Using the Front Panel Display ..............................................................................20

Playing Repeatedly (Repeat Play) ........................................................................22

Playing in Random Order (Shuffle Play) ............................................................23

Creating Your Own Program (Program Play)....................................................24

Resuming Playback from the Point Where You Stopped a Disc

(Resume Play)..........................................................................................................25

Reducing the Picture Noise (DNR: Digital Video Noise Reduction) ..............26

Changing the Sounds .............................................................................................26

Displaying the Subtitles .........................................................................................27

Changing the Angles ..............................................................................................27

Limiting Playback by Children (Parental Control)............................................28

Controlling the TV or the AV receiver with the Supplied Remote .................30

Enjoying the Dolby* Digital (AC-3) or DTS** Surround Sound ......................32

Settings and Adjustments

Using the Setup display .........................................................................................34

Setting the Language for Display and Sound (LANGUAGE SETUP) ............35

Settings for Display (INITIAL SETUP 1) .............................................................36

Settings for Sound (INITIAL SETUP 2) ...............................................................37

Settings for Output Signal Format (INITIAL SETUP 3) ....................................38

Additional Information

Precautions ..............................................................................................................39

Notes on Discs .........................................................................................................39

Troubleshooting ......................................................................................................40

Self-diagnosis function...........................................................................................42

Specifications ...........................................................................................................43

Glossary....................................................................................................................43

Index to Parts and Controls...................................................................................45

Setup Display Item List..........................................................................................48

Language Code List................................................................................................49

Index

Index .........................................................................................................................50

* Manufactured under license from Dolby Laboratories.

“Dolby”, “AC-3”, “Pro Logic” and the double-D symbol a are trademarks of Dolby

Laboratories.

** “DTS” is a trademark of Digital Theater Systems, Inc.

Getting Started

12 cm

74 min.

8 cm

20 min.

12 cm

74 min.

8 cm

(CD single)

20 min.

DVD VIDEOs

Audio + Video

12 cm

About 4 h (for

single-sided

DVD)/

about 8 h (for

double-sided

DVD)

8 cm

About 80 min.

(for

single-sided

DVD)/

about 160 min.

(for

double-sided

DVD)

VIDEO CDs

Audio + Video

Audio CDs

Audio

About This Manual

The instructions in this manual are for model DVP-S7700.

Conventions

• Instructions in this manual describe the controls on the

player.

You can also use the controls on the remote if they have

the same or similar names as those on the player.

• The icons on the right are used in this manual:

This Player Can Play the Following Discs

Disc logo

Contents

Disc size

Play time

“DVD VIDEO” logo is a trademark.

This player conforms to the NTSC color system. You cannot play discs recorded in other color systems such as PAL or SECAM.

Region code of DVDs you can play on this unit

Your DVD player has a region code printed on the back of the unit and will only play DVDs

that are labeled with identical region codes.

DVDs labeled

ALL

will also play on this unit.

If you try to play any other DVD, the message “Playing this disc prohibited by area limits.” will

appear on the TV screen.

Depending on the DVD, no region code indication may be labeled even though playing the DVD is prohibited by the area limits.

Note on playback operations of DVDs and VIDEO CDs

Some playback operations of DVDs and VIDEO CDs may be intentionally fixed by software producers. Since this player plays

DVDs and VIDEO CDs according to the disc contents the software producers designed, some playback features may not be

available. Also refer to the instructions supplied with the DVDs or VIDEO CDs.

Icon Meaning

Indicates that you can use only the remote

to do the task.

Indicates tips and hints for making the task

easier.

Indicates the functions for DVD VIDEOs.

Indicates the functions for VIDEO CDs.

Indicates the functions for Audio CDs.

Region code

MODEL NO.

DVP–8306

CD/DVD PLAYER

AC 110V 60Hz

22W

NO.

SONY CORPORATION

MADE IN JAPAN 3-444-464-01

Playing CDsGetting Started

Getting Started

DVD

structure

VIDEO CD

or CD

structure

Disc

Title

Chapter

Disc

Track

You can

Enjoy video playback (moving

pictures) as well as music.

Play interactive software using menu

screens displayed on the TV screen

(PBC Playback), in addition to the

video playback functions of Ver 1.1

discs. Moreover, you can play high-

resolution still pictures, if they are

included on the disc.

Terms for discs

• Title

The longest sections of a picture or a music piece on a DVD;

a movie, etc, for a picture piece on a video software; or an

album, etc, for a music piece on an audio software. Each

title is assigned a title number enabling you to locate the

title you want.

• Chapter

Sections of a picture or a music piece that are smaller than

titles. A title is composed of several chapters. Each chapter

is assigned a chapter number enabling you to locate the

chapter you want. Depending on the disc, no chapters may

be recorded.

• Track

Sections of a picture or a music piece on a VIDEO CD or a

CD. Each track is assigned a track number enabling you to

locate the track you want.

• Index (CD) / Video Index (VIDEO CD)

A number that divides a track some sections to easily locate

the point you want on a VIDEO CD or a CD. Depending

on the disc, no indexes may be recorded.

• Scene

On a VIDEO CD with PBC functions, the menu screens,

moving pictures and still pictures are divided into sections

called “scenes.” Each scene is assigned a scene number

enabling you to locate the scene you want.

Note on PBC (Playback Control) (VIDEO CDs)

This player conforms to Ver. 1.1 and Ver. 2.0 of VIDEO CD

standards. You can enjoy two kinds of playback according to

the disc type.

Disc type

VIDEO CDs

without PBC

functions

(Ver. 1.1 discs)

VIDEO CDs

with PBC

functions

(Ver. 2.0 discs)

Discs that the player cannot play

The player cannot play discs other than the ones listed in the

table on page 4. CD-ROMs including PHOTO CDs, data

sections in CD-EXTRAs and DVD-ROMs, etc. can not be

played.

Index

When playing DTS-encoded CDs, excessive noise will be

exhibited from the analog stereo outputs. To avoid possible

damage to the audio system, the consumer should take proper

pre-cautions when the analog stereo outputs of the DVD

player is connected to an amplification system. To enjoy DTS

Digital Surround playback, an external 5.1 channel DTS

Digital Surround decoder system must be connected to the

digital output of the DVD player.

This product incorporates copyright protection technology

that is protected by method claims of certain U.S. patents and

other intellectual property rights owned by Macrovision

Corporation and other rights owners. Use of this copyright

protection technology must be authorized by Macrovision

Corporation, and is intended for home and other limited

viewing uses only unless otherwise authorized by

Macrovision Corporation. Reverse engineering or

disassembly is prohibited.

Getting Started

Hooking Up the System

Overview

This section describes how to hook up the CD/DVD

player to a TV (with audio/video input jacks) and/or a

receiver (amplifier). You cannot connect this player to

a TV without a video input connector. Be sure to turn

off the power of each component before making

the connections.

pTo listen to the sound through TV speakers

pTo listen to the sound through speakers connected to a

receiver (amplifier)

CD/DVD player

To AUDIO

OUT

To VIDEO

OUT

To an AC outlet

To audio

input

To an AC outlet

: Signal flow

CD/DVD player

AUDIO

OUT

VIDEO

OUT

To an AC

outlet

To audio

input

: Signal flow

To an AC outlet

Receiver

(Amplifier)

To video input

Getting Started

Unpacking

Check that you have the following items:

• Audio connecting cord (1)

• Video connecting cord (1)

• S-link connecting cord (1)

• S video cord (1)

• Remote commander (remote) RMT-D107A (1)

• Size AA (R6) batteries (2)

Inserting batteries into the remote

You can control the player using the supplied remote.

Insert two R6 (size AA) batteries by matching the + and

– on the batteries. When using the remote, point it at

the remote sensor g on the player.

z You can control TVs and AV receivers using the

supplied remote

See page 30.

Notes

• Do not leave the remote in an extremely hot or humid place.

• Do not drop any foreign object into the remote casing,

particularly when replacing the batteries.

• Do not expose the remote sensor to direct sunlight or

lighting apparatuses. Doing so may cause a malfunction.

• If you will not use the remote for an extended period of

time, remove the batteries to avoid possible damage from

battery leakage and corrosion.

COMPONENT VIDEO OUT

B–Y

PR/

R–Y

R–AUDIO 2–L

LINE OUT

VIDEO 2

R–AUDIO 1–L VIDEO 1

S VIDEO OUT

OPTICAL COAXIAL

DOLBY DIGITAL (AC-3) IN

PCM/DTS/

CONTROL S

DIGITAL OUT S LINK

COMPONENT VIDEO OUT

B–Y

PR/

R–Y

R–AUDIO 2–L

LINE OUT

VIDEO 2

R–AUDIO 1–L VIDEO 1

S VIDEO OUT

OPTICAL COAXIAL

DOLBY DIGITAL (AC-3) IN

PCM/DTS/

CONTROL S

DIGITAL OUT S LINK

To video input

Playing CDsGetting Started

Getting Started

What cords will I need?

Video connecting cord (supplied) (1)

Audio connecting cord (supplied) (1)

Hookups

When connecting the cords, be sure to match the color-

coded cord to the appropriate jacks on the components:

Yellow (video) to Yellow, Red (right) to Red and White

(left) to White. Be sure to make connections firmly to

avoid hum and noise.

pTo listen to the sound through TV speakers

pTo listen to the sound through speakers connected to a

receiver (amplifier)

* Make the same connections when your receiver (amplifier)

conforms to “Pro Logic.”

Notes

• Do not connect this

player to a video deck.

If you view the pictures

on your TV after

making the connections

shown on the right, a

picture noise may

appear.

• Depending on the TV or receiver (amplifier), sound

distortion may occur because the audio output level is high.

In this case, set “AUDIO ATT” in “INITIAL SETUP 2” to

“ON” in the setup display. For details, see page 37.

Yellow Yellow

White (L)

Red (R)

White (L)

CD/DVD player

z If your TV has an S video input connector

Connect the component via the S VIDEO OUT connector

using the S video cord (supplied) instead of the video

connecting cord. You will get a better picture.

z If you connect the player to a monitor or projector

with component video input connectors that conform

to output signals from the COMPONENT VIDEO OUT

(Y, P

B/B-Y, PR/R-Y) connectors on the player

Connect the component via the COMPONENT VIDEO

OUT connectors using three video connecting cords (not

supplied) of the same kind. You will get a better picture.

Note

Refer to the instructions supplied with the component to be

connected.

z If your TV has an S-link connector

You can control the CD/DVD player from the TV.

Connect the TV via the S-LINK connector using the S-link

cord (supplied). Refer to the instructions supplied with

the TV to be connected.

(Continued)

LINE OUT

R–AUDIO 2–L

R–AUDIO 1–L VIDEO 1

VIDEO 2

INPUT

AUDIO

VIDEO

CD/DVD player

Amplifier*

INPUT

AUDIO

VIDEO

LINE OUT

R–AUDIO 2–L

R–AUDIO 1–L VIDEO 1

VIDEO 2

Connect

directly

Video deck

CD/DVD

player

CD/DVD player

S video cord (supplied)

S VIDEO IN

S VIDEO OUT

COMPONENT VIDEO OUT

R-Y

B-Y

CD/DVD player

S-link cord (supplied)

S-link

S-LINK

S LINK

CONTROL S

Getting Started

z If you have a digital component such as a receiver

(amplifier) with a digital connector, DAT or MD

Connect the component via the DIGITAL OUT OPTICAL

or COAXIAL connector using an optical or coaxial digital

connecting cord (not supplied).

When you play a DVD, set the items in “INITIAL SETUP

3” in the setup display as follows (page 38):

• DIGITAL OUT : ON

• DOLBY DIGITAL : D-PCM

• DTS : OFF.

p When using an optical digital connecting cord

Take off the cap and plug in the optical digital connecting

cord.

p When using a coaxial digital connecting cord

Notes

• Refer to the instructions supplied with the component

to be connected.

• You cannot make digital audio recordings of discs

recorded in DTS and Dolby Digital (AC-3) format

directly using an MD deck or DAT deck.

When you make the connections above, do not set

the items in “INITIAL SETUP 3” in the setup display

as follows:

• DOLBY DIGITAL : DOLBY DIGITAL

• DTS : ON.

If you set even one of them, a loud noise will

suddenly come out from the speakers, affecting

your ears or causing the speakers to be damaged.

z If you have a digital component with a built-in DTS or

Dolby Digital (AC-3) decoder

Connect the component via the DIGITAL OUT OPTICAL

or COAXIAL connector using an optical or coaxial digital

connecting cord (not supplied). For details on hookups

and settings, see page 32.

Optical digital connecting cord

(not supplied)

CD/DVD player

Receiver (Amplifier)

with a digital

connector, MD deck,

DAT deck, etc.

OPTICAL COAXIAL

DIGITAL IN

OPTICAL

DIGITAL OUT

PCM/DTS/

DOLBY DIGITAL (AC-3)

Coaxial digital connecting cord

(not supplied)

CD/DVD player

Receiver (Amplifier)

with a digital

connector, MD deck,

DAT deck, etc.

DIGITAL IN

COAXIAL

OPTICAL COAXIAL

DIGITAL OUT

PCM/DTS/

DOLBY DIGITAL (AC-3)

Playing CDsGetting Started

Getting Started

Necessary Setup Before Using

the Player

Some setups are necessary for the player depending on

the TV or other components to be connected.

For details on using the setup display, see page 34.

For details on each setup display item, see pages 35 to

38.

To enjoy DTS or Dolby Digital (AC-3) surround sound,

see page 32.

pTo connect the player to a wide-screen TV

In the setup display, set “TV TYPE” in “INITIAL SETUP

1” to “16:9.” For details, see page 36.

pTo connect the player to a normal TV

In the setup display, set “TV TYPE” in “INITIAL SETUP

1” to “4:3 LETTER BOX” (default setting) or “4:3 PAN

SCAN.” For details, see page 36.

pTo listen to the sound through speakers connected to a

receiver (amplifier) with a digital connector or to

output the sound to a digital component such as a DAT

or MD deck

When you play a DVD, set “DIGITAL OUT” to “ON”

and then, set “DOLBY DIGITAL” to “D-PCM” and

“DTS” to “OFF” in “INITIAL SETUP 3” in the setup

display. These are default settings. For details, see page

38.

pTo connect the player to a digital component with a

built-in Dolby Digital decoder

Set “DIGITAL OUT” to “ON” (default setting) and set

“DOLBY DIGITAL” to “DOLBY DIGITAL”, in “INITIAL

SETUP 3” in the setup display. For details, see page 32.

pTo connect the player to a digital component with a

built-in DTS decoder

Set “DIGITAL OUT” to “ON” (default setting) and set

“DTS” to “ON”, in “INITIAL SETUP 3” in the setup

display. For details, see page 32.

Use the setup display to change the various settings for

the picture and sound.

For details, see page 34.

Selecting the Language for

On-screen Display

You can select the language for the setup display or the

messages displayed on the screen. Default setting is

“ENGLISH.”

1 Press SET UP and select “ ” using ?//, and

then press ENTER.

2 Select “OSD” using >/., then press / or ENTER.

3 Select the language you want using >/., then

press ENTER.

To cancel using the setup display on the way

Press SET UP.

Note

The languages you can select are the ones displayed in step 2.

For details, see page 35.

SET UP

ENTER

?/>/.//

LANGUAGE SETUP

OSD: ENGLISH

ENGLISHDVD MENU:

AUDIO:

SUBTITLE:

ORIGINAL

AUDIO FOLLOW

1 2 3

LANGUAGE SETUP

OSD: ENGLISH

DVD MENU:

AUDIO:

SUBTITLE: AUDIO FOLLOW

1 2

FRENCH

SPANISH

1 2

CHOIX LANGUE D’AFFICHAGE

ECRANS: FRANÇAIS

ANGLAISMENU DVD:

AUDIO:

SOUS-TITRE:

ORIGINAL

SIGNAL AUDIO SUITE

Basic Operations

Make settings on your TV.

Turn on the TV and select the video input so that you can view

the pictures from this player.

When using an amplifier

Turn on the amplifier and select the appropriate position so that

you can listen to the sound from this player.

Press 1/u to turn on the player.

The indicator (red) above the 1/u button changes to green and

the front panel display lights up.

Press §, and place the disc on the disc tray.

Press ·.

The disc tray and front panel close, and the player starts

playback (Continuous Play). Adjust the volume on the TV or

the amplifier.

To open or close the front panel

Press UP/DOWN on the player.

Playing a DVD

• The operating procedure of CDs

or VIDEO CDs is different from

that of DVDs.

For details, see pages 14 to 17.

z You can turn on the player

using the remote

Press 1/u when the

indicator above the 1/u

button on the front panel is

lit in red.

* DTS indicator lights up when

you play DTS sound tracks on

a DVD. In this case, no sounds

will come out from the LINE

OUT (AUDIO 1, 2) and

PHONES connectors. To enjoy

the DTS sounds, you have to

connect an audio component

with a built-in DTS decoder

(see page 32).

z After following Step 4

A DVD menu or title menu

may appear on the TV screen

(see page 13).

243

With the playback

side facing down

Basic Operations

Depending on the DVD, some operations may be different or restricted. Refer to the instructions supplied with

your disc.

Connect headphones.

Adjust the headphone

volume.

DTS indicator*

UP/DOWN

Basic Operations

=/+

Number buttons

ENTER

SEARCH MODE

CLEAR

ENTER

Note

If you leave the player or the

remote in pause or stop mode for

15 minutes, the screen saver

image appears automatically. To

disappear the screen saver, press

·. (If you want to set the

screen saver function to off, see

page 36.)

z When “RESUME” appears on

the front panel display

You can resume playback

from the point where you

stopped the DVD. For

details on playing from the

beginning of the disc, see

page 25.

Note

You may not be able to do

Resume Play depending on the

DVD.

z What are chapter and title?

See page 5.

Note

Depending on the DVD, you

may not be able to do some of

the operations described on the

right.

z Each time you press SEARCH

MODE

“CHAPTER SEARCH,”

“TITLE SEARCH” and

“TIME SEARCH” appear on

the TV screen.

Stop

Pause

Resume play after pause

Go to the next chapter in

Continuous Play mode

Go back to the preceding

chapter in Continuous Play

mode

Select the chapter

Select the title

Locate a point using the time code

Stop play and remove the disc

If you have made a mistake when you press the number button.

Press CLEAR, then the correct number button.

Press

P or ·

1 SEARCH MODE repeatedly until “CHAPTER

SEARCH” appears on the TV screen.

2 Number buttons to select the chapter number,

then ENTER or ·.

1 SEARCH MODE repeatedly until “TITLE

SEARCH” appears on the TV screen.

2 Number buttons to select the title number, then

ENTER or ·.

1 SEARCH MODE repeatedly until “TIME

SEARCH” appears on the TV screen.

2 Number buttons to enter a time code, then

ENTER or ·.

123

456

789

π∏

Basic Operations

Click shuttle

JOG

Notes

• Depending on the DVD, you

may not be able to do some of

the operations described on the

right.

• When you play back a DVD at

twice the normal speed in

either direction, the sounds of

the picture will come out from

the LINE OUT (AUDIO 1, 2)

connectors. The sounds are

lower than the ones at normal

speed. In this case, no sounds

come out from the DIGITAL

OUT OPTICAL and COAXIAL

connectors.

To play at various speeds/frame-by-frame

Using the click shuttle and the JOG button/indicator, you can

playback a DVD with various speed or frame-by-frame. Each time

you press JOG, it changes between shuttle mode and jog mode.

pTo change the playback speed (Shuttle mode)

Turn the click shuttle. The playback speed changes depending on the turning

direction and angle as follows:

FF2) (about 30 times the normal speed)

FF1) (about 10 times the normal speed)

×2” (about twice the normal speed)

PLAY( (Normal speed)

SLOW1

(playback direction)

SLOW2

(playback direction

< – slower than “SLOW1

”)

PAUSEP

SLOW2

(opposite direction

< – slower than “SLOW1

”)

SLOW1

(opposite direction)

×2“ (about twice the normal speed : opposite direction)

FR10 (about 10 times the normal speed)

FR20 (about 30 times the normal speed)

If you turn the click shuttle quickly, the playback speed goes to FF2)/FR20

at once.

pTo play the DVDs frame-by-frame changing the playback speed (Jog mode)

1 Press JOG.

JOG lights up during jog mode.

2 Turn the click shuttle.

Depending on the turning speed, the playback goes to frame-by-frame toward

the turning direction of the click shuttle. If you turn the click shuttle with

constant speed for a while, the playback speed goes to slow or normal.

pTo return to Continuous Play

Press ·.

Note

If you don‘t operate the click

shuttle for about 20 seconds after

pressing JOG, it returns to shuttle

mode.

Basic Operations

Using the Title Menu

A DVD is divided into long sections of a picture or a music piece

called “titles.” When you play the DVD which contains several titles,

you can select the title you want using the title menu.

Press TITLE.

The title menu appears on the TV screen. The contents of the

menu varies from disc to disc.

Press ?/>/.// to select the title you want to play.

Depending on the disc, you can use the number buttons to

select the title.

Press ENTER.

The player starts playing the selected title.

Using the DVD menu

Some DVDs allow you to select the disc contents using the menu.

When you play these DVDs, you can select the language for the sub-

titles, the language for the sound, etc., using the DVD menu.

Press DVD MENU.

The DVD menu appears on the TV screen. The contents of the

menu vary from disc to disc.

Press ?/>/.// to select the item you want to change.

Depending on the disc, you can use the number buttons to

select the item.

To change other items, repeat Step 2.

Press ENTER.

TITLE

?/>/.//

ENTER

TITLE

?/>/.//

Notes

• Depending on the DVD, you

may not be able to select the

title.

• Depending on the DVD, a “title

menu” may simply be called a

“menu” or “title ” in the

instructions supplied with the

disc. “Press ENTER.” may also

be expressed as “Press

SELECT.”

DVD

DVD MENU

z If you want to select the

language for the DVD menu

Change the setting using

“LANGUAGE SETUP” in

the setup display. When you

select a language that is not

recorded on the DVD, one of

the recorded languages is

automatically selected (see

page 35).

Note

Depending on the DVD, a “DVD

menu” may simply be called a

“menu” in the instructions

supplied with the disc.

Basic Operations

Make settings on your TV.

Turn on the TV and select the video input so that you can view

the pictures from this player.

When using an amplifier

Turn on the amplifier and select the appropriate position so that

you can listen to the sound from this player.

Press 1/u to turn on the player.

The indicator (red) above the 1/u button changes to green and

the front panel display lights up.

Press §, and place the disc on the disc tray.

Press ·.

The disc tray and front panel close, and the player starts

playback (Continuous Play). Adjust the volume on the TV or

the amplifier.

To open or close the front panel

Press UP/DOWN on the player.

Playing a CD/VIDEO CD

• The operating procedure of DVDs

is different from that of CDs or

VIDEO CDs.

For details, see pages 10 to 13.

z You can turn on the player

using the remote

Press 1 /u when the

indicator above the 1 /u

button on the front panel is

lit in red.

* Do not play DTS sound tracks

on a CD without connecting

the player to an audio

component with a built-in DTS

decoder. DTS indicator does

not light up when you play

DTS sound tracks on a CD,

even if the player outputs DTS

signals via the DIGITAL OUT

OPTICAL and COAXIAL

connectors. In this case, a loud

noise will come out from the

LINE OUT (AUDIO 1, 2) and

PHONES connectors. To enjoy

the DTS sounds, you have to

connect an audio component

with a built-in DTS decoder

(see page 32).

z After following Step 4

The menu screen may

appear on the TV screen

depending on the VIDEO

CD. You can play the disc

interactively, following the

instructions on the menu

screen. (PBC Playback, see

page 17.)

243

With the label side

facing up

Basic Operations

Depending on the VIDEO CD, some operations may be different or restricted. Refer to the instructions supplied

with your disc.

Connect headphones.

Adjust the headphone

volume.

DTS indicator*

UP/DOWN

Basic Operations

=/+

ENTER

Number buttons

ENTER

CLEAR

Note

If you leave the player or the

remote in pause or stop mode for

15 minutes, the screen saver

image appears automatically. To

disappear the screen saver, press

·. (If you want to set the

screen saver function to off, see

page 36.)

z When “RESUME” appears on

the front panel display

You can resume playback

from the point where you

stopped the CD/VIDEO CD.

For details on playing from

the beginning of the disc, see

page 25.

z What is a track?

See page 5.

z What is an index?

See page 5.

z What is a scene?

See page 5.

z If you want to change the

search mode

Press SEARCH MODE. Each

time you press in case of a

VIDEO CD, “SCENE

SEARCH,” “TRACK

SEARCH” and “V. (VIDEO)

INDEX SEARCH” appear on

the TV screen. In case of a

CD, only “TRACK

SEARCH” appears.

Note

Some discs do not allow you to

start playing from a particular

scene. In this case, if you do

Scene Search before you start

playing, the player starts playing

from scene 1. If you do Scene

Search while playing a disc, the

player starts playing from the

current scene.

Stop

Pause

Resume play after pause

Go to the next track in

Continuous Play mode

Go back to the preceding

track in Continuous Play

mode

Select the track

Select the scene before you start

playing a VIDEO CD with PBC

functions and during PBC playback

(Scene Search)

Stop play and remove the disc

If you have made a mistake when you press the number button.

Press CLEAR, then the correct number button.

Press

P or ·

1 SEARCH MODE repeatedly until “TRACK

SEARCH” appears on the TV screen.

2 Number buttons to select the track number,

then ENTER or ·.

1 SEARCH MODE repeatedly until “SCENE

SEARCH” appears on the TV screen.

2 Number buttons to select the scene number,

then ENTER or ·. (To check the current scene

number, press DISPLAY. The scene number

appears at the left top of the TV screen.)

123

456

789

SEARCH MODE

∏

Basic Operations

Click shuttle

JOG

Notes

• Depending on the VIDEO CD,

you may not do some of the

operations described on the

right.

•When you play a VIDEO CD,

there is no sound except for the

playback at normal speed.

To play at various speeds / frame-by-frame

Using the click shuttle and the JOG button/indicator, you can

playback a CD/VIDEO CD with various speed or frame-by-frame.

Each time you press JOG, it changes between shuttle mode and jog

mode.

pTo change the playback speed (Shuttle mode)

Turn the click shuttle. The playback speed changes depending on the turning

direction and angle as follows:

FF2) (Faster than “FF1)”)

FF1)

×2” (about twice the normal speed)

PLAY( (Normal speed)

SLOW1

(playback direction)

< – VIDEO CD Only –

SLOW2

(playback direction

– Slower than “SLOW1

”)

< – VIDEO CD Only –

PAUSEP

FR10

FR20 (Faster than “FR10”)

If you turn the click shuttle quickly, the playback speed goes to FF2)/FR20

at once.

pTo play the VIDEO CDs frame-by-frame changing the playback speed (Jog mode –

VIDEO CD Only)

1 Press JOG.

JOG lights up during jog mode.

2 Turn the click shuttle.

Depending on the turning speed, the playback goes to frame-by-frame toward

the playback direction only. If you turn the click shuttle with constant speed for

a while, the playback speed goes to slow or normal.

pTo return to Continuous Play

Press ·.

Note

If you don‘t operate the click

shuttle for about 20 seconds after

pressing JOG, it returns to shuttle

mode.

Basic Operations

Playing VIDEO CDs with PBC Functions (PBC Playback –

VIDEO CD Only)

When playing VIDEO CDs with PBC functions (Ver. 2.0 discs), you

can enjoy simple interactive operations, operations with search

functions, etc.

PBC Playback allows you to play VIDEO CDs interactively, following

the menu screen on the TV screen.

On this player, you can use the number buttons, ENTER, =, +,

>/. and ˆ (RETURN) during PBC Playback.

Start playing a VIDEO CD with PBC functions, following Steps

1 to 4 in “Playing a CD/VIDEO CD” on page 14.

Select the item number you want.

On the player

Press >/. to select the item number.

On the remote

Press the number button of the item you want.

Press ENTER.

Follow the instructions on the menu screen for interactive

operations.

Refer to the instructions supplied with the disc, as the operating

procedure may differ according to the VIDEO CD.

Going back to the menu screen

Press ˆ, =, or +.

z When playing VIDEO CDs with

PBC functions

PBC playback starts

automatically.

z To cancel PBC playback of a

VIDEO CD with PBC functions

and play the disc in

Continuous Play mode

There are two ways.

• Before you start playing,

select the track you want

using =or +, then

press ENTER or ·.

• Before you start playing,

select the track number

using the number buttons

on the remote, then press

ENTER or ·.

“Play without PBC”

appears on the TV screen

and the player starts

Continuous Play. You

cannot play still pictures

such as a menu screen.

To return to PBC

playback, press p twice

then press ·.

Number

buttons

ˆ(RETURN) ENTER

>/.

=/+

>/.

ENTER

Note

Depending on the VIDEO CD,

“Press ENTER” in Step 3 may be

expressed as “Press SELECT” in

the instructions supplied with the

disc.

ˆ(RETURN)

123

456

789

Playing Discs in Various Modes

DISPLAY

TIME

Playing status

Current

play mode

Playing time

of the

current

chapter*

Current title

number

Current chapter

number

TITLE 32 PLAY

1 : 32 : 55

ALL

REPEAT

CHAPTER 30

CHAPTER

Current title

number (total

number of

titles)

Playing time

of the current

chapter*

Current language for the

subtitles (total number of

languages for subtitles)

Current

language

for the

sound (total

number of

languages

for the

sound)

Current chapter

number (total

number of

chapters in the

current title)

Selected angle

(total number of

angles)

Current audio

format**

Playing

status

Disc type

Using the On-Screen Display

You can check the operating status of the player and

the information about the disc using the on-screen

display on the TV screen.

When playing back or stopping a DVD

Press DISPLAY.

Each time you press the DISPLAY button, the on-

screen display changes as follows:

On-screen display 1

On-screen display 2

On-screen display 3

On-screen display off

pDisplay information of the on-screen display 1 mode

Rear component 2

Front component 2 +

Center component 1

LFE component 1

pDisplay information of the on-screen display 2 mode

Note

Some information may not be displayed depending on a

DVD.

* In display 1 or 2 mode, each time you press TIME the

information changes as shown below.

Playing time of the current chapter

Remaining time of the current chapter

Playing time of the current title

Remaining time of the current title

** “PCM”, “DTS” or “DOLBY DIGITAL” is displayed. In

“DOLBY DIGITAL” case, the channels in the playing track

are displayed by number as follows.

The case of Dolby Digital (AC-3) 5.1 ch:

Playing Discs in Various Modes

DVD

TITLE:

1 : 32 : 55

CHAPTER:

SUBTITLE:

AUDIO:

ANGLE:

32 ( 50 )

30 ( 50 )

ENGLISH ( 32 )

ENGLISH ( 8 )

1 ( 9 )

DOLBY DIGITAL

3 / 2. 1

CHAPTER

DNR: 2

PLAY

Current DNR

value

123

456

789

Playing CDs in Various Modes

Playing Discs in Various Modes

• During PBC playback (VIDEO CD Only)

pDisplay information of the on-screen display 2 mode

• During PBC playback (VIDEO CD Only)

pDisplay information of the on-screen display 3 mode

While playing a disc, the approximate bit rate of the

playback picture is always displayed by Mbps (Mega bit

per second).

z What is bit rate?

Bit rate refers to the amount of video data per second in a

disc. The higher the bit rate is, the larger the amount of

data. However, this does not always mean that you can

get higher quality pictures.

pDisplay information of the on-screen display off mode

No information is displayed. (Messages, etc., will be

displayed.)

When playing back or stopping a CD/VIDEO

Press DISPLAY.

Each time you press the button, the on-screen display

changes as follows:

On-screen display 1

On-screen display 2

On-screen display off

pDisplay information of the on-screen display 1 mode

Bit rate of the playback picture

BIT RATE

0510

Current

play

mode

Playing

time of

the

current

track*

Current track number

Current

index

number

Playing status

Playing

time

Current scene

number

Playing status

Current

play

mode

SCENE 122

05 : 27

TRACK

REPEAT

PLAY

VIDEO CD

12 : 07

PBC OFF

TRACK

TRACK:

V.INDEX:

11 ( 50 )

DNR:

PLAY

PBC Status

(VIDEO CD Only) Playing status

Current track

number (total

track number)

Current index

number

Disc type

Playing time

of the current

track*

PBC Status

Playing

time

Current scene

number (total

scene number)

Playing status

Disc type

Current DNR value

VIDEO CD

12 : 07

PBC ON

SCENE:

122 ( 159 )

DNR:

PLAY

Current DNR value

TRACK 11

12 : 07

TRACK

REPEAT

PLAY

INDEX 8

TRACK

Playing Discs in Various Modes

Disc type

Using the Front Panel Display

You can check information about the disc, such as the

total number of the titles or the tracks or remaining

time, using the front panel display.

When playing back a DVD

pDisplay information while playing the disc

pChecking the remaining time

Press TIME.

Each time you press TIME while playing the disc, the

display changes as shown in the chart to the right. The time

information in the on-screen display 1 and 2 also changes

each time you press TIME.

TIME

Playing status

Lights up while playing

the sections with the

auto pause signal

Lights up when

you can switch

the angles

Current

sound status

Lights up when you

can do Resume Play

Current

play

mode

Playing time

Current

title

number

Current

chapter

number

Lights up

during

programming

* In display 1 or 2 mode, each time you press TIME, the

information changes as shown below.

Playing time of the current track

Remaining time of the current track

Playing time of the disc

Remaining time of the disc

While you are doing Shuffle Play, Program Play, or

PBC Playback, the playing time of the disc and the

remaining time of the disc are not displayed.

pDisplay information of the on-screen display off mode

No information is displayed. (Messages, etc., will be

displayed.)

123

456

789

La page charge ...

Sony DVP-S7700 Le manuel du propriétaire

Marque: Sony

Modèle: DVP-S7700

Catégorie: Lecteurs DVD

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Sony DVP-S7700 Owner's manual

Sony DVP-S7700 Le manuel du propriétaire

Sony DVP-S7700 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents