VTech SN6307 Manuel utilisateur

Catégorie
Téléphones
Taper
Manuel utilisateur
BC
SN6307
Photo Speed Dial Handset
for use with
VTech CareLine™
User’s manual
Go to www.vtechphones.com
to register your product for
enhanced warranty support and
latest VTech product news
The ENERGY STAR
®
program
(www.energystar.gov) recognizes
and encourages the use of
products that save energy and
help protect our environment. We
are proud to mark this product
with the ENERGY STAR
®
label
indicating it meets the latest
energy efficiency guidelines.
Telephones identified with this
logo have reduced noise and
interference when used with
most T-coil equipped hearing
aids and cochlear implants.
The TIA-1083 Compliant
Logo is a trademark of the
Telecommunications Industry
Association. Used under license.
T
Compatible with
Hearing Aid T-Coil
TIA-1083
Congratulations
on purchasing your new VTech product.
Before using this product, please read
Important safet y instructions.
This user’s manual provides you with
installation and use instructions. Please
read this manual thoroughly to ensure
proper installation and operation of this
VTech product.
For support, shopping, and everything new
at VTech, visit our website at
www.vtechphones.com.
User’s manual
Parts checklist
Your product package contains the
following items. Save your sales receipt
and original packaging in the event
warranty service is necessary.
1
3
THIS SIDE UP
Install the battery
Install the battery as shown below.
NOTES
• Use only supplied battery.
• If the handset will not be used for a long time,
disconnect and remove the battery to prevent
possible leakage.
Connect and charge the battery
NOTES
• Use only the adapter provided.
• Charge the battery provided with this product
only in accordance with the instructions and
limitations specified in this manual.
• The adapter is intended to be correctly
oriented in a vertical or floor mount position.
The prongs are not designed to hold the plug
in place if it is plugged into a ceiling, under-
the-table or cabinet outlet.
Connect the charger
Charge the battery
Once you have installed the battery and
placed the handset in the charger, the
CHARGE light indicates the battery status
(see the table below).
NOTES
• For best performance, keep the handset in
the charger when not in use.
• The battery is fully charged after 12 hours of
continuous charging.
CHARGE
light
Battery st atus Action
Flashes
red every
10 seconds
The battery has
very little charge
and the handset
is not in charger.
The handset
cannot dial out.
Charge without
interruption
(at least
30 minutes).
Red The battery has
enough charge
to be used for a
short time.
Charge without
interruption
(at least
30 minutes).
Green The battery is
fully charged.
To keep the
battery charged,
place it in the
charger when
not in use.
Handset overview
1 – Incoming call light
2 – Earpiece
3 – CHARGE light
4 – Photo speed dial keys
• Press to dial a preset number.
5 –
• Make or answer a call.
• Press to put the current call on hold.
• During a call, press to answer an
incoming call when you receive a
call waiting alert.
6 –
• Hang up a call.
• Silence the ringer temporarily while
the phone is ringing.
• Mute the paging tone.
7 –
• Make or answer a call using the
speakerphone.
• Switch between the speakerphone
and the earpiece.
8 – Microphone
9 – Charging pole
10 – Speakerphone
11 – Battery compartment cover
12 – VOL+
• Increase the ringer volume and the
listening volume.
13 – VOL-
• Decrease the ringer volume and the
listening volume.
• Silence the ringer temporarily while
the phone is ringing.
• Mute the paging tone.
Charger overview
1 – Charging pole
Lights overview
The following table summarizes the lights
patterns on the handset under various
conditions.
Light Pattern
CHARGE
light
• Red when the handset battery
is charging.
• Flashes red every 10 seconds
when the handset battery is
low and not charging.
• Green when the handset
battery is fully charged.
• Alternates red and green
quickly when handset
registration is in progress.
• Alternates red and green
slowly when the handset is not
registered and not in charger.
Incoming
call light
• Flashes orange slowly when
the handset received an
incoming call.
• Green when the handset is on
earpiece mode.
• Flashes green slowly when
the handset received an
incoming call.
• Flashes green twice every
3 seconds when line in use
while the handset is idle.
• Orange when the handset is
on speakerphone mode.
Voice prompts
The following table summarizes voice
prompts you hear under certain conditions.
Voice Prompt Condition
Not registered Any key is pressed when the
handset is not registered.
Out of range Any key is pressed when
the handset is out of range.
Low battery
A photo speed dial key,
, or is pressed
when the handset battery
is low.
Before use
There are two types of Careline series
telephone. The instructions to register
and configure your SN6307 handset are
different for those two types of Careline
systems series telephone.
Use the diagrams on the right to identify
your Careline telephone, and then refer to
the respective section for instructions.
Operating range
This cordless handset operates with the
maximum power allowed by the Federal
Communications Commission (FCC). Even
so, this handset and telephone base can
communicate over only a certain distance
- which can vary with the locations of the
telephone base and handset, the weather,
and the layout of your home or office.
When the handset is out of range, the
handset plays the voice prompt “Out of
range” if any key is pressed. If there is a
call while the handset is out of range, it
may not ring, or if it does ring, the call may
not connect well when you press . Move
closer to the telephone base, then press
to answer the call.
During a call, if the handset is moved out
of range, the call will end automatically,
and you will hear a notification tone.
Identify your Careline telephone
1
2
For SN6127/SN6187 telephone:
Add and register a handset
Register each new SN6307 handset to
your Careline series telephone base before
use. Your telephone system supports a
maximum of 12 devices.
NOTE
Charge the new handset without interruption
for at least 30 minutes before registering it to
the telephone base.
1. Press and hold /FIND HANDSET at
the telephone base until the IN USE
light turns red.
2. Put the handset in the charger. The
handset CHARGE light alternates
red and green quickly to indicate the
registration is in progress.
You hear a confirmation tone when the
registration process completes. It takes up
to 60 seconds to complete the registration.
If registration fails, you hear an error tone,
and the CHARGE light alternates red and
green slowly when it is taken out of the
cradle. Start again from Step 1 above.
NOTES
• You cannot register a handset if any other
system device is in use.
• When you already have 12 registered
devices and you try to register another
handset to the telephone base, you hear four
beeps from the telephone base.
Set photo speed dial entries
Your handset has four photo speed
dial keys. It retrieves the photo speed
dial entries from the phonebook in the
telephone base.
Make sure you store the photo speed dial
entries in the phonebook naming
Photo 1,
Photo 2, Photo 3 and Photo 4
respectively.
NOTES
• Names for the photo speed dial entries are
case-sensitive.
• A space must be entered between “Photo” and
the number when entering the name of a photo
speed dial entry.
• Deleting an entry in phonebook will remove
the associated photo speed dial entry.
1. On a SN6127/SN6187 handset, press
MENU when idle.
2. Press q or p to scroll to Phonebook,
and then press SELECT.
3. Press q or p to scroll to Add contact,
and then press SELECT.
4. When the handset displays ENTER
NUMBER, use the dialing keys to enter
a number (up to 30 digits).
• Press q or p to move the cursor to
the left or right.
• Press DELETE to erase a digit.
• Press and hold DELETE to erase all
digits.
• Press and hold PAUSE to enter a
dialing pause (a P appears).
-OR-
Copy a number from the redial list by
pressing REDIAL then press q, p or
REDIAL repeatedly to find the desired
number. Press SELECT to copy the
number.
5. Press SELECT to save.
6. When the handset displays ENTER
NAME, use the dialing keys to enter
Photo 1, Photo 2, Photo 3 or Photo 4.
Press once or several times on the
dialing keys to enter the selected
character.
By default, the first character of each
word is uppercase, and the rest is
lowercase.
• Press q or p to move the cursor to
the left or right.
• Press 0 to add a space.
• Press to switch between the
uppercase and lowercase characters.
• Press DELETE to erase a character.
• Press and hold DELETE to erase all
characters.
7. Press SELECT to save. The handset
displays Saved and you hear a
confirmation tone.
For SN1157/SN1197/SN6147/SN6196/SN6197 telephone:
Add and register a handset
Register each new SN6307 handset to
your Careline series telephone base before
use. Your telephone system supports a
maximum of 12 devices.
NOTE
Charge the new handset without interruption for
at least 30 minutes before registering it to the
telephone base.
1. Press MENU on the telephone base
when it is not in use.
9:48am 5/20
BASE
CALL LOG
PHONEBOOK
2. Press or to scroll to Settings, and
then press SELECT.
9:48am 5/20
Set date/time
Annc Caller ID
Settings
BACK
SELECT
3. Press or to scroll to Registration,
then press SELECT. The telephone
base shows
Registering... Please wait
.
9:48am 5/20
SETTINGS
Dial mode
Registration
BACK
SELECT
4. Put the handset in the charger. The
handset CHARGE light alternates
red and green quickly to indicate the
registration is in progress.
You hear a confirmation tone when the
registration process completes. It takes up
to 60 seconds to complete the registration.
If registration fails, you hear an error tone,
and the CHARGE light alternates red and
green slowly when it is taken out of the
cradle. Start again from Step 1 above.
NOTES
• You cannot register a handset if any other
system devices is in use.
• The telephone base shows Registration
slots are full when you try to register more
than 12 devices to it.
• To cancel the registration, press CANCEL or
BACK.
Set photo speed dial entries
Your handset has four photo speed dial
keys. It retrieves the same set of photo
speed dial entries stored in the telephone
base.
If you have assigned the photo speed dial
entries at the telephone base before, your
handset is ready to use. Skip this part and
read Insert photos for speed dial keys.
NOTES
• You can store the same phone number in
more than one photo speed dial slots.
• If you have a pendant (SN6167) registered to
your telephone base, the speed dial entries
of the pendant are the same as the first two
photo speed dial entries of the telephone
base and the handset.
• Editing or deleting an entry in phonebook
does not affect the photo speed dial entries.
1. Press MENU on the telephone base
when it is not in use.
9:48am 5/20
BASE
CALL LOG
PHONEBOOK
-OR-
Press an unassigned photo speed dial
key on the telephone base, and then go
to Step 4.
2. Press or to scroll to Photo speed
dial, and then press SELECT.
9:48am 5/20
Answering system
Photo speed dial
Phonebook
BACK
SELECT
3. Press or to choose an unassigned
photo speed dial slot, and then press
SELECT.
9:48am 5/20
1:<Unassigned>
2:<Unassigned>
3:<Unassigned>
BACK
SELECT
4. When the base displays MEMORY X
NUMBER, use the dialing keys to enter
a number (up to 30 digits).
• Press q or p to move the cursor to
the left or right.
• Press X/DELETE or BACKSPACE to
erase a digit.
• Press and hold X/DELETE to erase
all digits.
• Press and hold PAUSE to enter a
dialing pause (a P appears).
5. Press NEXT.
9:48am 5/20
MEMORY 1 NUMBER
_
BACKSPA CE
NEXT
6. When the base displays MEMORY X
NAME, use the dialing keys to enter a
name (up to 15 characters).
Press once or several times on the
dialing keys to enter the selected
character.
By default, the first character of each
word is uppercase, and the rest is
lowercase.
• Press q or p to move the cursor to
the left or right.
• Press 0 to add a space.
• Press to switch between the
uppercase and lowercase characters.
• Press X/DELETE or BACKSPACE to
erase a character.
• Press and hold X/DELETE to erase
all characters.
7. Press SAVE. The screen displays
Memory X saved and you hear a
confirmation tone.
9:48am 5/20
MEMORY 1 NAME
_
BACKSPA CE
SAVE
Read the instructions for
SN1157/SN1197/SN6147/SN6196/SN6197 telephone.
Read the instructions for SN6127/SN6187 telephone.
Insert photos for speed dial
keys
You can add desired photos into the
photo speed dial compartments, or write
the contact name on the photo speed
dial cards.
To add a photo, use the photo speed dial
card as a tool to crop your desired photo,
and then insert it as shown below.
NOTE
The handset is shipped with protective stickers
covering the photo speed dial compartments.
Remove the protective sticker before use.
1
2
26.8 mm
14.5 mm
Settings
Adjust ringer volume
You can adjust the ringer volume level, or
turn the ringer off.
• When the handset is not in use, press
VOL- or VOL+.
NOTE
When the ringer volume is set to off, the
handset still rings when you press
/FIND HANDSET or FIND HS at the
telephone base.
Quiet mode
Your handset follows the quiet mode setting
in the telephone base. When the quiet mode
is on, all tones (except paging tone) are
muted.
Refer to the Quiet mode section in the
user’s manual of your Careline series
telephone base for the setting.
Caller ID announce
The voice announce caller ID feature lets
you know who the caller is. When you have
an incoming call, the handset speaks Call
from... and the name of the caller based
on the phonebook or caller ID information.
If the caller’s name is private or unknown,
the phone number up to the last 11 digits
will be announced. If the caller’s phone
number is also private or unknown, no
information will be announced.
To turn on or off this feature, refer to the
Caller ID announce section in the user’s
manual of the telephone base.
NOTES
• To use the caller ID announce feature, you
must subscribe to caller ID service from your
telephone service provider.
• When there are up to five handsets/pendants
registered, the telephone system supports
caller ID announce for all handsets/pendants.
If six or more handsets /pendants are
registered, the system supports caller
ID announce for the first four registered
handsets/pendants only.
For SN1157/SN1197/SN6147/
SN6196/SN6197 telephone:
1. Press and hold FIND HS at the
telephone base until the IN USE light
flashes and the telephone base shows
Registering... Please wait followed by
Deregister all devices?.
2. Immediately press YES or FIND HS
within 5 seconds
9:48am 5/20
Deregister
all devices?
NO
YES
You hear a confirmation tone when
the registration process completes. It
takes about 10 seconds to complete the
deregistration.
If deregistration fails, you need to reset
the system and try again. To reset, unplug the
power and the telephone line cord from the
telephone base. Then plug the cords back
in again.
VTech Communications, Inc.
A member of THE VTECH GROUP OF COMPANIES.
VTech is a registered trademark of VTech Holdings Limited.
Specifications are subject to change without notice.
© 2014 VTech Communications, Inc.
All rights reserved. 05/14. SN6307_CIB_V2.0
Document order number: 91-007352-020-100
Designed to fit your home.
And your life.
For SN6127/SN6187 telephone:
1. Press and hold /FIND HANDSET at
the telephone base until the IN USE
light flashes red.
2. Immediately press /FIND HANDSET
again within 5 seconds.
You hear a confirmation tone when
the registration process completes. It
takes about 10 seconds to complete the
deregistration.
If deregistration fails, you need to reset the
system and try again. To reset, unplug the
power and the telephone line cord from the
telephone base. Then plug the cords back
in again.
ECO mode
This power conserving technology reduces
power consumption for optimal battery
performance. The ECO mode activates
automatically whenever the handset is
synchronized with the telephone base.
General product care
Taking care of your telephone
Your cordless telephone contains sophisticated
electronic parts, so it must be treated with care.
Avoid rough treatment
Place the handset down gently. Save the
original packing materials to protect your
telephone if you ever need to ship it.
Avoid water
Your telephone can be damaged if it gets wet.
Do not use the handset outdoors in the rain,
or handle it with wet hands. Do not install the
telephone base near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power
surges harmful to electronic equipment. For
your own safety, take caution when using
electrical appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic casing that
should retain its luster for many years. Clean it
only with a dry non-abrasive cloth. Do not use
dampened cloth or cleaning solvents of any
kind.
Storage
When you are not going to use the handset
for some time, remove the rechargeable
battery from the handset. Store the handset,
the charger and the adapter in a cool and dry
place.
Frequently asked questions
Below are the questions most frequently asked
about the cordless telephone. If you cannot find
the answer to your question, visit our website at
www.vtechphones.com or call
1 (800) 595-9511 for customer service. In
Canada, go to www.vtechcanada.com or call
1 (800) 267-7377.
My handset
does not work
at all.
Make sure the charger
is installed properly, and
battery is installed and
charged correctly. For
optimum daily performance,
return the handset to the
charger after use.
Make sure the handset has
registered to a Careline
series telephone base.
I cannot dial out. For different type of Careline
series telephone base, the
photo speed dial setup
procedure is different.
Make sure you have set the
photo speed dial entries
in the telephone base as
instructed.
I experience
poor sound
quality when
using the
handset
speakerphone.
For increased sound quality
while using the handset
speakerphone, place the
handset on a flat surface
with the keys facing up.
The handset
does not ring
when there is an
incoming call.
Press VOL+ to increase
the ringer volume when the
handset is not in use.
Make sure the quiet mode
is off. Check the setting on
your telephone base.
Important safety instructions
When using your telephone equipment, basic
safety precautions should always be followed to
reduce the risk of fire, electric shock and injury,
including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked
on the product.
3. Unplug this product from the wall outlet
before cleaning. Do not use liquid or aerosol
cleaners. Use a dry non-abrasive cloth for
cleaning.
4. Do not use this product near water such as
near a bath tub, wash bowl, kitchen sink,
laundry tub or a swimming pool, or in a wet
basement or shower.
5. Do not place this product on an unstable
table, shelf, stand or other unstable surfaces.
6. Slots and openings in the back or bottom of
the charger and handset are provided for
ventilation. To protect them from overheating,
these openings must not be blocked by
placing the product on a soft surface such as
a bed, sofa or rug. This product should never
be placed near or over a radiator or heat
register. This product should not be placed
in any area where proper ventilation is not
provided.
7. This product should be operated only from
the type of power source indicated on the
marking label. If you are not sure of the
type of power supply in your home or office,
consult your dealer or local power company.
8. Do not allow anything to rest on the power
cord. Do not install this product where the
cord may be walked on.
9. Never push objects of any kind into this
product through the slots in the charger or
handset because they may touch dangerous
voltage points or create a short circuit.
Never spill liquid of any kind on the product.
10. To reduce the risk of electric shock, do
not disassemble this product, but take it to
an authorized service facility. Opening or
removing parts of the charger or handset
other than specified access doors may
expose you to dangerous voltages or
other risks. Incorrect reassembling can
cause electric shock when the product is
subsequently used.
11. Do not overload wall outlets and extension
cords.
12. Unplug this product from the wall outlet
and refer servicing to an authorized service
facility under the following conditions:
• When the power supply cord or plug is
damaged or frayed.
• If liquid has been spilled onto the product.
• If the product has been exposed to rain or
water.
• If the product does not operate normally
by following the operating instructions.
Adjust only those controls that are
covered by the operation instructions.
Improper adjustment of other controls
may result in damage and often requires
extensive work by an authorized
technician to restore the product to normal
operation.
• If the product has been dropped and
the charger and/or handset has been
damaged.
• If the product exhibits a distinct change in
performance.
13. Avoid using a telephone (other than
cordless) during an electrical storm. There
is a remote risk of electric shock from
lightning.
14. Do not use the telephone to report a gas
leak in the vicinity of the leak. Under certain
circumstances, a spark may be created
when the adapter is plugged into the power
outlet, or when the handset is replaced in its
cradle. This is a common event associated
with the closing of any electrical circuit. The
user should not plug the phone into a power
outlet, and should not put a charged handset
into the cradle, if the phone is located in an
environment containing concentrations of
flammable or flame-supporting gases, unless
there is adequate ventilation. A spark in
such an environment could create a fire or
explosion. Such environments might include:
medical use of oxygen without adequate
ventilation; industrial gases (cleaning
solvents; gasoline vapors; etc.); a leak of
natural gas; etc.
15. Only put the handset next to your ear when
it is in normal talk mode.
16. The power adapter is intended to be
correctly oriented in a vertical or floor mount
position. The prongs are not designed to
hold the plug in place if it is plugged into a
ceiling, under-the-table or cabinet outlet.
SAVE THESE INSTRUCT IONS
Battery
• CAUTION: Use Only Supplied Battery.
• Do not dispose of the battery in a fire. Check
with local waste management codes for
special disposal instructions.
• Do not open or mutilate the battery. Released
electrolyte is corrosive and may cause burns
or injury to the eyes or skin. The electrolyte
may be toxic if swallowed.
• Exercise care in handling batteries in order
not to create a short circuit with conductive
materials.
• Charge the battery provided with this product
only in accordance with the instructions and
limitations specified in this manual.
Precautions for users of implanted
cardiac pacemakers
Cardiac pacemakers (applies only to digital
cordless telephones):
Wireless Technology Research, LLC (WTR),
an independent research entity, led a
multidisciplinary evaluation of the interference
between portable wireless telephones and
implanted cardiac pacemakers. Supported by
the U.S. Food and Drug Administration, WTR
recommends to physicians that:
Pacemaker patients
• Should keep wireless telephones at least six
inches from the pacemaker.
• Should NOT place wireless telephones
directly over the pacemaker, such as in a
breast pocket, when it is turned ON.
• Should use the wireless telephone at the ear
opposite the pacemaker.
WTR’s evaluation did not identify any risk to
bystanders with pacemakers from other persons
using wireless telephones.
About cordless telephones
• Privacy: The same features that make a
cordless telephone convenient create some
limitations. Telephone calls are transmitted
between the telephone base and the
cordless handset by radio waves, so there
is a possibility that the cordless telephone
conversations could be intercepted by radio
receiving equipment within range of the
cordless handset. For this reason, you should
not think of cordless telephone conversations
as being as private as those on corded
telephones.
• Electrical power: The telephone base of this
cordless telephone must be connected to a
working electrical outlet. The electrical outlet
should not be controlled by a wall switch.
Calls cannot be made from the cordless
handset if the telephone base is unplugged,
switched off or if the electrical power is
interrupted.
• Potential TV interference: Some cordless
telephones operate at frequencies that may
cause interference to televisions and VCRs.
To minimize or prevent such interference, do
not place the telephone base of the cordless
telephone near or on top of a TV or VCR.
If interference is experienced, moving the
cordless telephone farther away from the
TV or VCR often reduces or eliminates the
interference.
• Rechargeab le batteries: Exercise care in
handling batteries in order not to create a
short circuit with conducting material such
as rings, bracelets and keys. The battery or
conductor may overheat and cause harm.
Observe proper polarity between the battery
and the battery charger.
• Nickel-me tal hydride recharg eable
batteries: Dispose of these batteries in a
safe manner. Do not burn or puncture the
battery. Like other batteries of this type, if
burned or punctured, they could release
caustic material which could cause injury.
The RBRC
®
seal
The RBRC
®
seal on the nickel-metal hydride
battery indicates that VTech Communications,
Inc. is voluntarily participating in an industry
program to collect and recycle these batteries at
the end of their useful lives, when taken out of
service within the United States and Canada.
The RBRC
®
program provides a convenient
alternative to placing used nickel-metal hydride
batteries into the trash or municipal waste,
which may be illegal in your area.
VTech’s participation in RBRC
®
makes it easy
for you to drop off the spent battery at local
retailers participating in the RBRC
®
program
or at authorized VTech product service
centers. Please call 1 (800) 8 BATTERY
TM
for
information on Ni-MH battery recycling and
disposal bans/restrictions in your area. VTech’s
involvement in this program is part of its
commitment to protecting our environment and
conserving natural resources.
RBRC
®
is a registered
trademark of Rechargeable
Battery Recycling
Corporation.
FCC and IC regulations
FCC Part 15
This equipment has been tested and found to
comply with the requirements for a Class B
digital device under Part 15 of the Federal
Communications Commission (FCC) rules.
These requirements are intended to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/
TV technician for help.
Changes or modifications to this equipment not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
This device complies with Part 15 of the FCC
rules. Operation is subject to the following
two conditions: (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation. Privacy of communications may not
be ensured when using this telephone.
To ensure safety of users, the FCC has
established criteria for the amount of radio
frequency energy that can be safely absorbed
by a user or bystander according to the
intended usage of the product. This product has
been tested and found to comply with the FCC
criteria.
This Class B digital apparatus complies with
Canadian requirement:
CAN ICES-3 (B)/NMB-3(B)
FCC Part 68 and ACTA
This equipment complies with Part 68 of the
FCC rules and with technical requirements
adopted by the Administrative Council for
Terminal Attachments (ACTA). The label on
the back or bottom of this equipment contains,
among other things, a product identifier in the
format US:AAAEQ##TXXXX. This identifier
must be provided to your telephone service
provider upon request.
The plug and jack used to connect this
equipment to premises wiring and the telephone
network must comply with applicable Part 68
rules and technical requirements adopted by
ACTA. A compliant telephone cord and modular
plug is provided with this product. It is designed
to be connected to a compatible modular jack
that is also compliant. An RJ11 jack should
normally be used for connecting to a single
line and an RJ14 jack for two lines. See the
installation instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used
to determine how many devices you may connect
to your telephone line and still have them ring
when you are called. The REN for this product is
encoded as the 6th and 7th characters following
the US: in the product identifier (e.g., if ## is 03,
the REN is 0.3). In most, but not all areas, the sum
of all RENs should be five (5.0) or less. For more
information, please contact your telephone service
provider.
This equipment may not be used with Party
Lines. If you have specially wired alarm dialing
equipment connected to your telephone line,
ensure the connection of this equipment
does not disable your alarm equipment. If you
have questions about what will disable alarm
equipment, consult your telephone service
provider or a qualified installer.
If this equipment is malfunctioning, it must
be unplugged from the modular jack until the
problem has been corrected. Repairs to this
telephone equipment can only be made by the
manufacturer or its authorized agents. For repair
procedures, follow the instructions outlined
under the Limited warranty.
If this equipment is causing harm to the
telephone network, the telephone service
provider may temporarily discontinue your
telephone service. The telephone service
provider is required to notify you before
interrupting service. If advance notice is not
practical, you will be notified as soon as
possible. You will be given the opportunity to
correct the problem and the telephone service
provider is required to inform you of your right
to file a complaint with the FCC. Your telephone
service provider may make changes in its
facilities, equipment, operation, or procedures
that could affect the proper functioning of
this product. The telephone service provider
is required to notify you if such changes are
planned.
If this product is equipped with a corded or
cordless handset, it is hearing aid compatible.
If this product has memory dialing locations,
you may choose to store emergency telephone
numbers (e.g., police, fire, medical) in these
locations. If you do store or test emergency
numbers, please: Remain on the line and briefly
explain the reason for the call before hanging
up.
Perform such activities in off-peak hours, such
as early morning or late evening.
Industry Canada
This device complies with Industry Canada
licence-exempt RSS standard(s).
Operation is subject to the following two
conditions: (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
Privacy of communications may not be ensured
when using this telephone.
The term ‘’IC:‘’ before the certification/
registration number only signifies that the
Industry Canada technical specifications were
met.
The Ringer Equivalence Number (REN) for
this terminal equipment is NAN. The REN
is an indication of the maximum number of
devices allowed to be connected to a telephone
interface. The termination on an interface may
consist of any combination of devices subject
only to the requirement that the sum of the
RENs of all the devices does not exceed five.
Remark: The word “NAN” means “Not
Applicable”.
This product meets the applicable Industry Canada
technical specifications.
RF radiation exposure statement
The handset complies with FCC RF radiation
exposure limits set forth for an uncontrolled
environment. Use of other accessories may
not ensure compliance with FCC RF exposure
guidelines. This transmitter must not be co-
located or operating in conjunction with any
other antenna or transmitter. This equipment
complies also with Industry Canada RSS-102
with respect to Canada’s Health Code 6 for
Exposure of Humans to RF Fields.
California Energy Commission
battery charging testing instructions
This telephone is set up to comply with the
energy-conserving standards right out of
the box. These instructions are intended
for California Energy Commission (CEC)
compliance testing only. When the CEC battery
charging testing mode is activated, all telephone
functions, except battery charging, will be
disabled.
When first purchased and properly installed
for charging (see Install the battery), put the
handset on the charger to charge. The CEC
battery charging testing mode is activated while
charging.
If you have registered the handset to a Careline
series telephone base, below are the testing
instructions.
For SN1157/SN1197/SN6147/SN6196/SN6197
telephone:
To activate the CEC battery charging
testing mode
NOTE
Your telephone base and the corded handset
can still function normally when the CEC battery
charging testing mode is activated.
1. Press and hold FIND HS at the telephone
base until the IN USE light flashes and
the telephone base shows Registering...
Please wait followed by Deregister all
devices?.
2. Immediately press YES or FIND HS
within 5 seconds.
To deactivate the CEC battery charging
testing mode
• Register your handsets back to the
telephone base. Refer to the Add and
register a handset section of your
Careline series user ’s manual and this
manual.
For SN6127/SN6187 telephone:
To activate the CEC battery charging
testing mode
1. Unplug the telephone base power
adapter from the power outlet. Make
sure all handsets are plugged with
charged batteries before proceeding.
2. While you press and hold
/FIND
HANDSET
, plug the telephone base
power adapter back to the power outlet.
3. After about 20 seconds, when the
IN USE light starts flashing quickly,
release /FIND HANDSET and then
press it again within 5 seconds.
When the phone successfully enters the
CEC battery charging testing mode, the
IN USE light turns off.
NOTES
• When the phone fails to enter this mode, repeat
Step 1 through Step 3 above.
• The telephone base will be powered up as
normal if you fail to press /FIND HANDSET
within 2 seconds in Step 3.
To deactivate the CEC battery charging
testing mode
1. Unplug the telephone base power adapter
from the power outlet, then plug it back in.
Then the telephone base is powered up
as normal.
2. Register your handsets back to the
telephone base. Refer to the Add and
register a handset section of your
Careline series user’s manual and this
manual.
For C-UL compliance only
Mesures de sécurité importantes
Afin de réduire les risques d’incendie, de
blessures corporelles ou d’électrocution, suivez
toujours ces mesures préventives de base
lorsque vous utilisez votre téléphone :
1. Lisez et comprenez bien toutes les
instructions.
2. Observez toutes les instructions et mises en
garde inscrites sur l’appareil.
3. branchez ce téléphone de la prise murale
avant de le nettoyer. N’utilisez pas de
nettoyeurs liquides ni en aérosol. N’utilisez
qu’un chiffon doux et légèrement humecté.
4. N’utilisez pas ce produit près de l’eau, tel
que près d’un bain, d’un lavabo, d’un évier
de cuisine, d’un bac de lavage ou d’une
piscine, ou dans un sous-sol humide ou
sous la douche.
5. Ne déposez pas ce téléphone sur un chariot,
support ou table chancelants. L’appareil
pourrait tomber et être sérieusement
endommagé.
6. Le boîtier de l’appareil est doté de fentes et
d’ouvertures d’aération situées à l’arrière ou
en dessous. Afin d’empêcher la surchauffe,
ces ouvertures ne doivent pas être obstruées
en plaçant l’appareil sur un lit, divan, tapis
ou autre surface similaires. Ne placez pas
cet appareil à proximité d’un élément de
chauffage ni d’une plinthe électrique. De plus,
ne l’installez pas dans une unité murale ou un
cabinet fermé qui ne possède pas d’aération
adéquate.
7. Ne faites fonctionner cet appareil qu’avec le
type d’alimentation indiqué sur les étiquettes
de l’appareil. Si vous ne connaissez pas le
voltage de votre maison, consultez votre
marchand ou votre fournisseur d’électricité.
8. Ne déposez rien sur le cordon
d’alimentation. Installez cet appareil dans un
endroit sécuritaire, là où personne ne pourra
trébucher sur la ligne d’alimentation ni le
cordon téléphonique modulaire.
9. N’insérez jamais d’objets à travers les
fentes et ouvertures de cet appareil, car ils
pourraient toucher à des points de tension
dangereux ou court-circuiter des pièces,
ce qui constituerait un risque d’incendie ou
d’électrocution. N’échappez pas de liquides
dans l’appareil.
10. Afin de réduire les risques d’électrocution,
ne démontez pas l’appareil, mais
apportez-le plutôt à un centre de service
qualifié s’il doit être réparé. En enlevant
le couvercle, vous vous exposez à des
tensions dangereuses ou autres dangers
similaires. Un remontage inadéquat peut
être à l’origine d’une électrocution lors
d’une utilisation ultérieure de l’appareil.
Débranchez l’appareil avant de procéder
au nettoyage. Utilisez un chiffon humide et
doux.
11. Ne surchargez pas les prises de courant et les
rallonges.
12. Débranchez cet appareil de la prise
de courant et communiquez avec le
département de service à la clientèle de
VTech dans les cas suivants :
• Lorsque le cordon d’alimentation est
endommagé ou écorché.
• Si du liquide a été échappé dans
l’appareil.
• Si l’appareil a été exposé à une source
d’humidité telle que la pluie ou l’eau.
• Si le produit ne fonctionne pas
normalement en respectant les
instructions de fonctionnement.
Réglez uniquement les commandes
indiquées dans le les instructions de
fonctionnement. Les réglages incorrects
des autres commandes pourraient
provoquer un dommage qui pourrait
exiger un travail exhaustif de la part d’un
technicien autorisé afin de rétablir le
fonctionnement normal de l’appareil.
• Si le produit a été échappé et que le socle
et/ou le combiné a été endommagé.
• Si le produit affiche une nette diminution
de sa performance.
13. Évitez d’utiliser un téléphone (autre qu’un
sans fil) pendant un orage. Les éclairs
peuvent être à l’origine d’une électrocution.
14. N’utilisez pas le téléphone pour rapporter
une fuite de gaz à proximité de la fuite. En
certaines circonstances, une flammèche
pourrait être provoquée lorsque l’adaptateur
est branché à une prise de courant, ou
lorsque le combiné est déposé sur le socle.
Ceci est un événement commun associé à la
fermeture d’un circuit électrique. L’utilisateur
ne devrait pas brancher le téléphone à une
prise de courant, et ne devrait pas déposer le
combiné chargé sur le socle, si le téléphone
se trouve à proximité d’un endroit comportant
des concentrations de gaz inflammables,
à moins que la ventilation soit adéquate.
Une flammèche dans un tel endroit pourrait
provoquer un incendie ou une explosion. De
tels environnements peuvent comprendre:
des endroits où l’on utilise de l’oxygène
médical sans ventilation adéquate; des gaz
industriels (dissolvants de nettoyage, des
vapeurs d’essence, etc.); une fuite de gaz
naturel, etc.
15. Ne placez que le combiné de votre
téléphone près de votre oreille lorsqu’en
mode de conversation.
16. Ces adaptateurs ont été conçus pour être
orientés en position verticale ou montés au
sol. Les broches ne sont pas conçues pour
maintenir l’adaptateur en place si celui-ci est
barnché dans une prise au plafond ou sous
une table/ armoire.
CONSERVEZ CES INSTRUCTION S
Pile
• MISE EN GARDE : N’utilisez que la pile
incluse.
• Ne jetez pas la pile au feu. Vérifiez les
instructions spécifiques de mise aux rebus
auprès des autorités locales.
• N’ouvrez pas et ne mutilez pas la pile.
L’électrolyte qui s’en échapperait est corrosif
et pourrait causer des brûlures ou des
blessures aux yeux ou à la peau. L’électrolyte
est toxique si avalé.
• Soyez prudents lorsque vous manipulez les
piles afin d’éviter les courts-circuits provoqués
par des matériaux conducteurs.
• Rechargez la pile incluse avec cet appareil,
selon les instructions et limites spécifiées
dans ce guide d’utilisation.
Stimulateurs cardiaques implantés
dans l’organisme
Les simulateurs cardiaques (s’applique uniquement
aux téléphones numériques sans fil) :
L’organisme ‘Wireless Technology Research,
LLC (WTR)’, une firme de recherche
indépendante, a mené une évaluation
pluridisciplinaire des interférences entre les
téléphones sans fil portatifs et les stimulateurs
cardiaques implantés dans l’organisme.
Appuyée par l’Administration des aliments et
drogues (FDA) des États-Unis, la firme WTR
recommande aux médecins :
Avis aux détenteurs de stimulateurs cardi-
aques
• Ils doivent tenir le téléphone sans fil à
une distance d’au moins six pouces du
stimulateur cardiaque.
• Ils ne doivent PAS placer le téléphone sans
fil directement sur le stimulateur cardiaque,
tel que dans une poche de chemise, lorsque
celui-ci est en marche.
• Ils doivent utiliser le téléphone sans fil en
l’appuyant sur l’oreille qui se trouve dans la
direction opposée au stimulateur cardiaque.
L’étude effectuée par l’organisme WRS n’a
pas identifié de risque pour les détenteurs de
simulateurs cardiaques causés par les gens
qui utilisent un téléphone sans fil à proximité de
ceux-ci.
À propos des téléphones sans l
• Condentialité : Les mêmes
caractéristiques qui constituent des
avantages pour les téléphones sans fil
affichent également des restrictions. Les
appels téléphoniques sont transmis entre
le combiné sans fil et le socle par le biais
d’ondes radio ; il y a donc la possibilité que
vos conversations téléphoniques sans fil
soient interceptées par des équipements de
réception radio se trouvant dans la portée
du combiné sans fil. Pour cette raison, vous
ne devez pas percevoir les communications
téléphoniques sans fil comme étant aussi
confidentielles que celles des téléphones à
cordons.
• Alimentation électrique : Le socle de
ce téléphone sans fil doit être branché à
une prise électrique fonctionnelle. La prise
électrique ne doit pas être contrôlée par un
interrupteur mural. Les appels ne pourront
pas être effectués du combiné sans fil si le
socle est débranché ou mis hors tension ou
si le courant est coupé.
• Possibilité d’interférences aux téléviseurs :
Certains téléphones sans fil fonctionnent
sur des fréquences pouvant causer des
interférences aux téléviseurs et aux
magnétoscopes. Pour réduire ou prévenir de
telles interférences, ne placez pas le socle du
téléphone sans fil près ou sur un téléviseur
ou magnétoscope. S’il y a présence de
parasites, il est conseillé d’éloigner le
téléphone sans fil du téléviseur ou du
magnétoscope afin de réduire possiblement
les interférences.
• Piles rechargeables : Manipulez les piles
avec soin afin de ne pas les cour t-circuiter
avec des bagues, bracelets ou clés. Les
piles ou le conducteur peut surchauffer et
causer des blessures. Respectez la polarité
adéquate entre la pile et le chargeur.
Les bloc-piles re chargeables à l’hydrure
métallique de nickel : Jetez ces blocs-piles
de manière écologique et sécuritaire. Ne les
incinérez pas et ne les percez pas. Tel que
les autres piles de ce type, elles pourraient
dégager une matière toxique qui peut causer
des blessures corporelles si elles sont
brûlées ou percées.
Limited warranty
What does this limited warranty cover?
The manufacturer of this VTech Product
warrants to the holder of a valid proof of
purchase (“Consumer” or “you”) that the
Product and all accessories provided in the
sales package (“Product”) are free from defects
in material and workmanship, pursuant to the
following terms and conditions, when installed
and used normally and in accordance with the
Product operating instructions. This limited
warranty extends only to the Consumer for
Products purchased and used in the United
States of America and Canada.
What will VTech do if the Product is not free
from defects in materials and workmanship
during the limited warranty period
(“Materially Defective Product”)?
During the limited warranty period, VTech’s
authorized service representative will repair
or replace at VTech’s option, without charge,
a Materially Defective Product. If we repair
the Product, we may use new or refurbished
replacement parts. If we choose to replace
the Product, we may replace it with a new or
refurbished Product of the same or similar
design. We will retain defective parts, modules,
or equipment. Repair or replacement of the
Product, at VTech’s option, is your exclusive
remedy. VTech will return the repaired or
replacement Products to you in working
condition. You should expect the repair or
replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product
extends for ONE (1) YEAR from the date
of purchase. If VTech repairs or replaces a
Materially Defective Product under the terms of
this limited warranty, this limited warranty also
applies to the repaired or replacement Product
for a period of either (a) 90 days from the date
the repaired or replacement Product is shipped
to you or
(b) the time remaining on the original
one-year warranty; whichever is longer.
What is not covered by this limited
warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse,
accident, shipping or other physical
damage, improper installation, abnormal
operation or handling, neglect, inundation,
fire, water or other liquid intrusion; or
2. Product that has been damaged due
to repair, alteration or modification by
anyone other than an authorized service
representative of VTech; or
3. Product to the extent that the problem
experienced is caused by signal conditions,
network reliability, or cable or antenna
systems; or
4. Product to the extent that the problem is
caused by use with non-VTech accessories;
or
5. Product whose warranty/quality stickers,
product serial number plates or electronic
serial numbers have been removed, altered
or rendered illegible; or
6. Product purchased, used, serviced, or
shipped for repair from outside the United
States of America or Canada, or used
for commercial or institutional purposes
(including but not limited to Products used
for rental purposes); or
7. Product returned without a valid proof of
purchase (see item 2 on the next page); or
8. Charges for installation or set up,
adjustment of customer controls, and
installation or repair of systems outside the
unit.
How do you get warranty service?
NOTE: Before calling for service, please review
the user’s manual - a check of the Product’s
controls and features may save you a service
call.
Except as provided by applicable law, you
assume the risk of loss or damage during
transit and transportation and are responsible
for delivery or handling charges incurred
in the transport of the Product(s) to the
service location. VTech will return repaired or
replaced Product under this limited warranty.
Transportation, delivery or handling charges are
prepaid. VTech assumes no risk for damage
or loss of the Product in transit. If the Product
failure is not covered by this limited warranty, or
proof of purchase does not meet the terms of
this limited warranty, VTech will notify you and
will request that you authorize the cost of repair
prior to any further repair activity. You must pay
for the cost of repair and return shipping costs
for the repair of Products that are not covered
by this limited warranty.
What must you return with the Product to
get warranty service?
1. Return the entire original package and
contents including the Product to the VTech
service location along with a description of
the malfunction or difficulty; and
2. Include a “valid proof of purchase” (sales
receipt) identifying the Product purchased
(Product model) and the date of purchase or
receipt; and
3. Provide your name, complete and correct
mailing address, and telephone number.
Other limitations
This warranty is the complete and exclusive
agreement between you and VTech.
It supersedes all other written or oral
communications related to this Product. VTech
provides no other warranties for this Product.
The warranty exclusively describes all of
VTech’s responsibilities regarding the Product.
There are no other express warranties. No
one is authorized to make modifications to this
limited warranty and you should not rely on any
such modification.
State/Provincial Law Rights: This warranty gives
you specific legal rights, and you may also have
other rights, which vary from state to state or
province to province.
Limitations: Implied warranties, including
those of fitness for a particular purpose and
merchantability (an unwritten warranty that
the Product is fit for ordinary use) are limited
to one year from the date of purchase. Some
states/provinces do not allow limitations on how
long an implied warranty lasts, so the above
limitation may not apply to you. In no event
shall VTech be liable for any indirect, special,
incidental, consequential, or similar damages
(including, but not limited to lost profits or
revenue, inability to use the Product or other
associated equipment, the cost of substitute
equipment, and claims by third parties) resulting
from the use of this Product. Some states/
provinces do not allow the exclusion or limitation
of incidental or consequential damages, so the
above limitation or exclusion may not apply to
you.
Please retain your original sales receipt
as proof of purchase.
Technical specifications
Frequency
control
Crystal controlled PLL synthesizer
Transmit
frequency
1921.536-1928.448 MHz
Channels 5
Nominal
effective
range
Maximum power allowed by
FCC and IC. Actual operating
range may vary according to
environmental conditions at the
time of use.
Power
requirements
Battery:
2.4V 400mAh, Ni-MH battery pack
Power adapter: 6V AC @ 300mA
Using the photo speed dial
handset
Make a call
• Press a photo speed dial key to dial.
-OR-
• Press or , and then a photo
speed dial key to dial.
Answer a call
• Press or .
End a call
• Press or place the handset back in
the charger.
Speakerphone
• During a call, press to switch
between the speakerphone and the
earpiece.
Adjust listening Volume
• During a call, press VOL- or VOL+.
Call waiting
When you subscribe to call waiting service
from your telephone service provider, you
hear an alert tone if there is an incoming
call while you are already on a call.
• Press to put the current call on hold
and take the new call.
• Press at any time to switch back and
forth between calls.
Temporary ringer silence
When the telephone is ringing, you can
temporarily silence the handset ringer
without disconnecting the call. The next
call rings normally at the preset volume.
• Press VOL- or .
Join a call in progress
You can use a maximum of four devices at
a time on a call.
• Press or to join the call.
• To exit the call, press or place the
handset back in the charger. The call
continues until all devices hang up.
Find handset
You can use the Find handset feature
on the telephone base to find misplaced
handsets.
• Press a photo speed dial key, , or
to stop paging.
• Press or VOL- to mute the paging
tone.
Deregister handsets
Your telephone system supports a
maximum of 12 devices.
If you have registered 12 devices, and you
want to register a SN6307 handset, you
have to deregister all devices first. Then
register your desired devices individually.
CAUTION
• Deregister with caution! Once done, all
devices will be deregistered from your
telephone system.
NOTES
• You cannot deregister all devices if any other
system device is in use.
• Even if your devices have run out of battery,
you can still deregister them by following the
instructions in this section.
• To register any cordless handset or pendant
back to the telephone base, refer to the
user’s manual of your Careline series
telephone for details.
  • Page 1 1
  • Page 2 2

VTech SN6307 Manuel utilisateur

Catégorie
Téléphones
Taper
Manuel utilisateur

dans d''autres langues