VTech SN6307 Manuel utilisateur

Marque: VTech

Modèle: SN6307

Catégorie: Téléphones

Taper: Manuel utilisateur

SN6307

Photo Speed Dial Handset

for use with

VTech CareLine™

User’s manual

Go to www.vtechphones.com

to register your product for

enhanced warranty support and

latest VTech product news

The ENERGY STAR

program

(www.energystar.gov) recognizes

and encourages the use of

products that save energy and

help protect our environment. We

are proud to mark this product

with the ENERGY STAR

label

indicating it meets the latest

energy efﬁciency guidelines.

Telephones identiﬁed with this

logo have reduced noise and

interference when used with

most T-coil equipped hearing

aids and cochlear implants.

The TIA-1083 Compliant

Logo is a trademark of the

Telecommunications Industry

Association. Used under license.

Compatible with

Hearing Aid T-Coil

TIA-1083

Congratulations

on purchasing your new VTech product.

Before using this product, please read

Important safet y instructions.

This user’s manual provides you with

installation and use instructions. Please

read this manual thoroughly to ensure

proper installation and operation of this

VTech product.

For support, shopping, and everything new

at VTech, visit our website at

www.vtechphones.com.

User’s manual

Parts checklist

Your product package contains the

following items. Save your sales receipt

and original packaging in the event

warranty service is necessary.

THIS SIDE UP

Install the battery

Install the battery as shown below.

NOTES

• Use only supplied battery.

• If the handset will not be used for a long time,

disconnect and remove the battery to prevent

possible leakage.

Connect and charge the battery

NOTES

• Use only the adapter provided.

• Charge the battery provided with this product

only in accordance with the instructions and

limitations speciﬁed in this manual.

• The adapter is intended to be correctly

oriented in a vertical or ﬂoor mount position.

The prongs are not designed to hold the plug

in place if it is plugged into a ceiling, under-

the-table or cabinet outlet.

Connect the charger

Charge the battery

Once you have installed the battery and

placed the handset in the charger, the

CHARGE light indicates the battery status

(see the table below).

NOTES

• For best performance, keep the handset in

the charger when not in use.

• The battery is fully charged after 12 hours of

continuous charging.

CHARGE

light

Battery st atus Action

Flashes

red every

10 seconds

The battery has

very little charge

and the handset

is not in charger.

The handset

cannot dial out.

Charge without

interruption

(at least

30 minutes).

Red The battery has

enough charge

to be used for a

short time.

Charge without

interruption

(at least

30 minutes).

Green The battery is

fully charged.

To keep the

battery charged,

place it in the

charger when

not in use.

Handset overview

1 – Incoming call light

2 – Earpiece

3 – CHARGE light

4 – Photo speed dial keys

• Press to dial a preset number.

5 –

• Make or answer a call.

• Press to put the current call on hold.

• During a call, press to answer an

incoming call when you receive a

call waiting alert.

6 –

• Hang up a call.

• Silence the ringer temporarily while

the phone is ringing.

• Mute the paging tone.

7 –

• Make or answer a call using the

speakerphone.

• Switch between the speakerphone

and the earpiece.

8 – Microphone

9 – Charging pole

10 – Speakerphone

11 – Battery compartment cover

12 – VOL+

• Increase the ringer volume and the

listening volume.

13 – VOL-

• Decrease the ringer volume and the

listening volume.

• Silence the ringer temporarily while

the phone is ringing.

• Mute the paging tone.

Charger overview

1 – Charging pole

Lights overview

The following table summarizes the lights

patterns on the handset under various

conditions.

Light Pattern

CHARGE

light

• Red when the handset battery

is charging.

• Flashes red every 10 seconds

when the handset battery is

low and not charging.

• Green when the handset

battery is fully charged.

• Alternates red and green

quickly when handset

registration is in progress.

• Alternates red and green

slowly when the handset is not

registered and not in charger.

Incoming

call light

• Flashes orange slowly when

the handset received an

incoming call.

• Green when the handset is on

earpiece mode.

• Flashes green slowly when

the handset received an

incoming call.

• Flashes green twice every

3 seconds when line in use

while the handset is idle.

• Orange when the handset is

on speakerphone mode.

Voice prompts

The following table summarizes voice

prompts you hear under certain conditions.

Voice Prompt Condition

“Not registered” Any key is pressed when the

handset is not registered.

“Out of range” Any key is pressed when

the handset is out of range.

“Low battery”

A photo speed dial key,

, or is pressed

when the handset battery

is low.

Before use

There are two types of Careline series

telephone. The instructions to register

and conﬁgure your SN6307 handset are

different for those two types of Careline

systems series telephone.

Use the diagrams on the right to identify

your Careline telephone, and then refer to

the respective section for instructions.

Operating range

This cordless handset operates with the

maximum power allowed by the Federal

Communications Commission (FCC). Even

so, this handset and telephone base can

communicate over only a certain distance

- which can vary with the locations of the

telephone base and handset, the weather,

and the layout of your home or ofﬁce.

When the handset is out of range, the

handset plays the voice prompt “Out of

range” if any key is pressed. If there is a

call while the handset is out of range, it

may not ring, or if it does ring, the call may

not connect well when you press . Move

closer to the telephone base, then press

to answer the call.

During a call, if the handset is moved out

of range, the call will end automatically,

and you will hear a notiﬁcation tone.

Identify your Careline telephone

For SN6127/SN6187 telephone:

Add and register a handset

your Careline series telephone base before

use. Your telephone system supports a

maximum of 12 devices.

NOTE

Charge the new handset without interruption

for at least 30 minutes before registering it to

the telephone base.

1. Press and hold /FIND HANDSET at

the telephone base until the IN USE

light turns red.

2. Put the handset in the charger. The

handset CHARGE light alternates

red and green quickly to indicate the

registration is in progress.

You hear a conﬁrmation tone when the

registration process completes. It takes up

to 60 seconds to complete the registration.

If registration fails, you hear an error tone,

and the CHARGE light alternates red and

green slowly when it is taken out of the

cradle. Start again from Step 1 above.

NOTES

• You cannot register a handset if any other

system device is in use.

• When you already have 12 registered

devices and you try to register another

handset to the telephone base, you hear four

beeps from the telephone base.

Set photo speed dial entries

Your handset has four photo speed

dial keys. It retrieves the photo speed

dial entries from the phonebook in the

telephone base.

Make sure you store the photo speed dial

entries in the phonebook naming

Photo 1,

Photo 2, Photo 3 and Photo 4

respectively.

NOTES

• Names for the photo speed dial entries are

case-sensitive.

• A space must be entered between “Photo” and

the number when entering the name of a photo

speed dial entry.

• Deleting an entry in phonebook will remove

the associated photo speed dial entry.

1. On a SN6127/SN6187 handset, press

MENU when idle.

2. Press q or p to scroll to Phonebook,

and then press SELECT.

3. Press q or p to scroll to Add contact,

and then press SELECT.

4. When the handset displays ENTER

NUMBER, use the dialing keys to enter

a number (up to 30 digits).

• Press q or p to move the cursor to

the left or right.

• Press DELETE to erase a digit.

• Press and hold DELETE to erase all

digits.

• Press and hold PAUSE to enter a

dialing pause (a P appears).

-OR-

Copy a number from the redial list by

pressing REDIAL then press q, p or

REDIAL repeatedly to ﬁnd the desired

number. Press SELECT to copy the

number.

5. Press SELECT to save.

6. When the handset displays ENTER

NAME, use the dialing keys to enter

Photo 1, Photo 2, Photo 3 or Photo 4.

Press once or several times on the

dialing keys to enter the selected

character.

By default, the ﬁrst character of each

word is uppercase, and the rest is

lowercase.

• Press q or p to move the cursor to

the left or right.

• Press 0 to add a space.

• Press to switch between the

uppercase and lowercase characters.

• Press DELETE to erase a character.

• Press and hold DELETE to erase all

characters.

7. Press SELECT to save. The handset

displays Saved and you hear a

conﬁrmation tone.

For SN1157/SN1197/SN6147/SN6196/SN6197 telephone:

Add and register a handset

your Careline series telephone base before

use. Your telephone system supports a

maximum of 12 devices.

NOTE

Charge the new handset without interruption for

at least 30 minutes before registering it to the

telephone base.

1. Press MENU on the telephone base

when it is not in use.

9:48am 5/20

BASE

CALL LOG

PHONEBOOK

2. Press or to scroll to Settings, and

then press SELECT.

9:48am 5/20

Set date/time

Annc Caller ID

Settings

BACK

SELECT

3. Press or to scroll to Registration,

then press SELECT. The telephone

base shows

Registering... Please wait

9:48am 5/20

SETTINGS

Dial mode

Registration

BACK

SELECT

4. Put the handset in the charger. The

handset CHARGE light alternates

red and green quickly to indicate the

registration is in progress.

You hear a conﬁrmation tone when the

registration process completes. It takes up

to 60 seconds to complete the registration.

If registration fails, you hear an error tone,

and the CHARGE light alternates red and

green slowly when it is taken out of the

cradle. Start again from Step 1 above.

NOTES

• You cannot register a handset if any other

system devices is in use.

• The telephone base shows Registration

slots are full when you try to register more

than 12 devices to it.

• To cancel the registration, press CANCEL or

BACK.

Set photo speed dial entries

Your handset has four photo speed dial

keys. It retrieves the same set of photo

speed dial entries stored in the telephone

base.

If you have assigned the photo speed dial

entries at the telephone base before, your

handset is ready to use. Skip this part and

read Insert photos for speed dial keys.

NOTES

• You can store the same phone number in

more than one photo speed dial slots.

• If you have a pendant (SN6167) registered to

your telephone base, the speed dial entries

of the pendant are the same as the ﬁrst two

photo speed dial entries of the telephone

base and the handset.

• Editing or deleting an entry in phonebook

does not affect the photo speed dial entries.

1. Press MENU on the telephone base

when it is not in use.

9:48am 5/20

BASE

CALL LOG

PHONEBOOK

-OR-

Press an unassigned photo speed dial

key on the telephone base, and then go

to Step 4.

2. Press or to scroll to Photo speed

dial, and then press SELECT.

9:48am 5/20

Answering system

Photo speed dial

Phonebook

BACK

SELECT

3. Press or to choose an unassigned

photo speed dial slot, and then press

SELECT.

9:48am 5/20

1:<Unassigned>

2:<Unassigned>

3:<Unassigned>

BACK

SELECT

4. When the base displays MEMORY X

NUMBER, use the dialing keys to enter

a number (up to 30 digits).

• Press q or p to move the cursor to

the left or right.

• Press X/DELETE or BACKSPACE to

erase a digit.

• Press and hold X/DELETE to erase

all digits.

• Press and hold PAUSE to enter a

dialing pause (a P appears).

5. Press NEXT.

9:48am 5/20

MEMORY 1 NUMBER

BACKSPA CE

6. When the base displays MEMORY X

NAME, use the dialing keys to enter a

name (up to 15 characters).

Press once or several times on the

dialing keys to enter the selected

character.

By default, the ﬁrst character of each

word is uppercase, and the rest is

lowercase.

• Press q or p to move the cursor to

the left or right.

• Press 0 to add a space.

• Press to switch between the

uppercase and lowercase characters.

• Press X/DELETE or BACKSPACE to

erase a character.

• Press and hold X/DELETE to erase

all characters.

7. Press SAVE. The screen displays

Memory X saved and you hear a

conﬁrmation tone.

9:48am 5/20

MEMORY 1 NAME

BACKSPA CE

SAVE

Read the instructions for

SN1157/SN1197/SN6147/SN6196/SN6197 telephone.

Read the instructions for SN6127/SN6187 telephone.

Insert photos for speed dial

keys

You can add desired photos into the

photo speed dial compartments, or write

the contact name on the photo speed

dial cards.

To add a photo, use the photo speed dial

card as a tool to crop your desired photo,

and then insert it as shown below.

NOTE

The handset is shipped with protective stickers

covering the photo speed dial compartments.

Remove the protective sticker before use.

26.8 mm

14.5 mm

Settings

Adjust ringer volume

You can adjust the ringer volume level, or

turn the ringer off.

• When the handset is not in use, press

VOL- or VOL+.

NOTE

When the ringer volume is set to off, the

handset still rings when you press

/FIND HANDSET or FIND HS at the

telephone base.

Quiet mode

Your handset follows the quiet mode setting

in the telephone base. When the quiet mode

is on, all tones (except paging tone) are

muted.

Refer to the Quiet mode section in the

user’s manual of your Careline series

telephone base for the setting.

Caller ID announce

The voice announce caller ID feature lets

you know who the caller is. When you have

an incoming call, the handset speaks “ Call

from...” and the name of the caller based

on the phonebook or caller ID information.

If the caller’s name is private or unknown,

the phone number up to the last 11 digits

will be announced. If the caller’s phone

number is also private or unknown, no

information will be announced.

To turn on or off this feature, refer to the

Caller ID announce section in the user’s

manual of the telephone base.

NOTES

• To use the caller ID announce feature, you

must subscribe to caller ID service from your

telephone service provider.

• When there are up to ﬁve handsets/pendants

registered, the telephone system supports

caller ID announce for all handsets/pendants.

If six or more handsets /pendants are

registered, the system supports caller

ID announce for the ﬁrst four registered

handsets/pendants only.

For SN1157/SN1197/SN6147/

SN6196/SN6197 telephone:

1. Press and hold FIND HS at the

telephone base until the IN USE light

ﬂashes and the telephone base shows

Registering... Please wait followed by

Deregister all devices?.

2. Immediately press YES or FIND HS

within 5 seconds

9:48am 5/20

Deregister

all devices?

YES

You hear a conﬁrmation tone when

the registration process completes. It

takes about 10 seconds to complete the

deregistration.

If deregistration fails, you need to reset

the system and try again. To reset, unplug the

power and the telephone line cord from the

telephone base. Then plug the cords back

in again.

VTech Communications, Inc.

A member of THE VTECH GROUP OF COMPANIES.

VTech is a registered trademark of VTech Holdings Limited.

Speciﬁcations are subject to change without notice.

Document order number: 91-007352-020-100

Designed to ﬁt your home.

And your life.

For SN6127/SN6187 telephone:

1. Press and hold /FIND HANDSET at

the telephone base until the IN USE

light ﬂashes red.

2. Immediately press /FIND HANDSET

again within 5 seconds.

You hear a conﬁrmation tone when

the registration process completes. It

takes about 10 seconds to complete the

deregistration.

If deregistration fails, you need to reset the

system and try again. To reset, unplug the

power and the telephone line cord from the

telephone base. Then plug the cords back

in again.

ECO mode

This power conserving technology reduces

power consumption for optimal battery

performance. The ECO mode activates

automatically whenever the handset is

synchronized with the telephone base.

General product care

Taking care of your telephone

Your cordless telephone contains sophisticated

electronic parts, so it must be treated with care.

Avoid rough treatment

Place the handset down gently. Save the

original packing materials to protect your

telephone if you ever need to ship it.

Avoid water

Your telephone can be damaged if it gets wet.

Do not use the handset outdoors in the rain,

or handle it with wet hands. Do not install the

telephone base near a sink, bathtub or shower.

Electrical storms

Electrical storms can sometimes cause power

surges harmful to electronic equipment. For

your own safety, take caution when using

electrical appliances during storms.

Cleaning your telephone

Your telephone has a durable plastic casing that

should retain its luster for many years. Clean it

only with a dry non-abrasive cloth. Do not use

dampened cloth or cleaning solvents of any

kind.

Storage

When you are not going to use the handset

for some time, remove the rechargeable

battery from the handset. Store the handset,

the charger and the adapter in a cool and dry

place.

Frequently asked questions

Below are the questions most frequently asked

about the cordless telephone. If you cannot ﬁnd

the answer to your question, visit our website at

www.vtechphones.com or call

1 (800) 595-9511 for customer service. In

Canada, go to www.vtechcanada.com or call

1 (800) 267-7377.

My handset

does not work

at all.

Make sure the charger

is installed properly, and

battery is installed and

charged correctly. For

optimum daily performance,

return the handset to the

charger after use.

Make sure the handset has

registered to a Careline

series telephone base.

I cannot dial out. For different type of Careline

series telephone base, the

photo speed dial setup

procedure is different.

Make sure you have set the

photo speed dial entries

in the telephone base as

instructed.

I experience

poor sound

quality when

using the

handset

speakerphone.

For increased sound quality

while using the handset

speakerphone, place the

handset on a ﬂat surface

with the keys facing up.

The handset

does not ring

when there is an

incoming call.

Press VOL+ to increase

the ringer volume when the

handset is not in use.

Make sure the quiet mode

is off. Check the setting on

your telephone base.

Important safety instructions

When using your telephone equipment, basic

safety precautions should always be followed to

reduce the risk of ﬁre, electric shock and injury,

including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked

on the product.

3. Unplug this product from the wall outlet

before cleaning. Do not use liquid or aerosol

cleaners. Use a dry non-abrasive cloth for

cleaning.

4. Do not use this product near water such as

near a bath tub, wash bowl, kitchen sink,

laundry tub or a swimming pool, or in a wet

basement or shower.

5. Do not place this product on an unstable

table, shelf, stand or other unstable surfaces.

6. Slots and openings in the back or bottom of

the charger and handset are provided for

ventilation. To protect them from overheating,

these openings must not be blocked by

placing the product on a soft surface such as

a bed, sofa or rug. This product should never

be placed near or over a radiator or heat

in any area where proper ventilation is not

provided.

7. This product should be operated only from

the type of power source indicated on the

marking label. If you are not sure of the

type of power supply in your home or ofﬁce,

consult your dealer or local power company.

8. Do not allow anything to rest on the power

cord. Do not install this product where the

cord may be walked on.

9. Never push objects of any kind into this

product through the slots in the charger or

handset because they may touch dangerous

voltage points or create a short circuit.

Never spill liquid of any kind on the product.

10. To reduce the risk of electric shock, do

not disassemble this product, but take it to

an authorized service facility. Opening or

removing parts of the charger or handset

other than speciﬁed access doors may

expose you to dangerous voltages or

other risks. Incorrect reassembling can

cause electric shock when the product is

subsequently used.

11. Do not overload wall outlets and extension

cords.

12. Unplug this product from the wall outlet

and refer servicing to an authorized service

facility under the following conditions:

• When the power supply cord or plug is

damaged or frayed.

• If liquid has been spilled onto the product.

• If the product has been exposed to rain or

water.

• If the product does not operate normally

by following the operating instructions.

Adjust only those controls that are

covered by the operation instructions.

Improper adjustment of other controls

may result in damage and often requires

extensive work by an authorized

technician to restore the product to normal

operation.

• If the product has been dropped and

the charger and/or handset has been

damaged.

• If the product exhibits a distinct change in

performance.

13. Avoid using a telephone (other than

cordless) during an electrical storm. There

is a remote risk of electric shock from

lightning.

14. Do not use the telephone to report a gas

leak in the vicinity of the leak. Under certain

circumstances, a spark may be created

when the adapter is plugged into the power

outlet, or when the handset is replaced in its

cradle. This is a common event associated

with the closing of any electrical circuit. The

user should not plug the phone into a power

outlet, and should not put a charged handset

into the cradle, if the phone is located in an

environment containing concentrations of

ﬂammable or ﬂame-supporting gases, unless

there is adequate ventilation. A spark in

such an environment could create a ﬁre or

explosion. Such environments might include:

medical use of oxygen without adequate

ventilation; industrial gases (cleaning

solvents; gasoline vapors; etc.); a leak of

natural gas; etc.

15. Only put the handset next to your ear when

it is in normal talk mode.

16. The power adapter is intended to be

correctly oriented in a vertical or ﬂoor mount

position. The prongs are not designed to

hold the plug in place if it is plugged into a

ceiling, under-the-table or cabinet outlet.

SAVE THESE INSTRUCT IONS

Battery

• CAUTION: Use Only Supplied Battery.

• Do not dispose of the battery in a ﬁre. Check

with local waste management codes for

special disposal instructions.

• Do not open or mutilate the battery. Released

electrolyte is corrosive and may cause burns

or injury to the eyes or skin. The electrolyte

may be toxic if swallowed.

• Exercise care in handling batteries in order

not to create a short circuit with conductive

materials.

• Charge the battery provided with this product

only in accordance with the instructions and

limitations speciﬁed in this manual.

Precautions for users of implanted

cardiac pacemakers

Cardiac pacemakers (applies only to digital

cordless telephones):

Wireless Technology Research, LLC (WTR),

an independent research entity, led a

multidisciplinary evaluation of the interference

between portable wireless telephones and

implanted cardiac pacemakers. Supported by

the U.S. Food and Drug Administration, WTR

recommends to physicians that:

Pacemaker patients

• Should keep wireless telephones at least six

inches from the pacemaker.

• Should NOT place wireless telephones

directly over the pacemaker, such as in a

breast pocket, when it is turned ON.

• Should use the wireless telephone at the ear

opposite the pacemaker.

WTR’s evaluation did not identify any risk to

bystanders with pacemakers from other persons

using wireless telephones.

About cordless telephones

• Privacy: The same features that make a

cordless telephone convenient create some

limitations. Telephone calls are transmitted

between the telephone base and the

cordless handset by radio waves, so there

is a possibility that the cordless telephone

conversations could be intercepted by radio

receiving equipment within range of the

cordless handset. For this reason, you should

not think of cordless telephone conversations

as being as private as those on corded

telephones.

• Electrical power: The telephone base of this

cordless telephone must be connected to a

working electrical outlet. The electrical outlet

should not be controlled by a wall switch.

Calls cannot be made from the cordless

handset if the telephone base is unplugged,

switched off or if the electrical power is

interrupted.

• Potential TV interference: Some cordless

telephones operate at frequencies that may

cause interference to televisions and VCRs.

To minimize or prevent such interference, do

not place the telephone base of the cordless

telephone near or on top of a TV or VCR.

If interference is experienced, moving the

cordless telephone farther away from the

TV or VCR often reduces or eliminates the

interference.

• Rechargeab le batteries: Exercise care in

handling batteries in order not to create a

short circuit with conducting material such

as rings, bracelets and keys. The battery or

conductor may overheat and cause harm.

Observe proper polarity between the battery

and the battery charger.

• Nickel-me tal hydride recharg eable

batteries: Dispose of these batteries in a

safe manner. Do not burn or puncture the

battery. Like other batteries of this type, if

burned or punctured, they could release

caustic material which could cause injury.

The RBRC

seal

The RBRC

seal on the nickel-metal hydride

battery indicates that VTech Communications,

Inc. is voluntarily participating in an industry

program to collect and recycle these batteries at

the end of their useful lives, when taken out of

service within the United States and Canada.

The RBRC

program provides a convenient

alternative to placing used nickel-metal hydride

batteries into the trash or municipal waste,

which may be illegal in your area.

VTech’s participation in RBRC

makes it easy

for you to drop off the spent battery at local

retailers participating in the RBRC

program

or at authorized VTech product service

centers. Please call 1 (800) 8 BATTERY

for

information on Ni-MH battery recycling and

disposal bans/restrictions in your area. VTech’s

involvement in this program is part of its

commitment to protecting our environment and

conserving natural resources.

RBRC

is a registered

trademark of Rechargeable

Battery Recycling

Corporation.

FCC and IC regulations

FCC Part 15

This equipment has been tested and found to

comply with the requirements for a Class B

digital device under Part 15 of the Federal

Communications Commission (FCC) rules.

These requirements are intended to provide

reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there is

no guarantee that interference will not occur

in a particular installation. If this equipment

does cause harmful interference to radio or

television reception, which can be determined

by turning the equipment off and on, the user is

encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/

TV technician for help.

Changes or modiﬁcations to this equipment not

expressly approved by the party responsible for

compliance could void the user’s authority to

operate the equipment.

This device complies with Part 15 of the FCC

rules. Operation is subject to the following

two conditions: (1) this device may not cause

harmful interference, and (2) this device must

accept any interference received, including

interference that may cause undesired

operation. Privacy of communications may not

be ensured when using this telephone.

To ensure safety of users, the FCC has

established criteria for the amount of radio

frequency energy that can be safely absorbed

by a user or bystander according to the

intended usage of the product. This product has

been tested and found to comply with the FCC

criteria.

This Class B digital apparatus complies with

Canadian requirement:

CAN ICES-3 (B)/NMB-3(B)

FCC Part 68 and ACTA

This equipment complies with Part 68 of the

FCC rules and with technical requirements

adopted by the Administrative Council for

Terminal Attachments (ACTA). The label on

the back or bottom of this equipment contains,

among other things, a product identiﬁer in the

format US:AAAEQ##TXXXX. This identiﬁer

must be provided to your telephone service

provider upon request.

The plug and jack used to connect this

equipment to premises wiring and the telephone

network must comply with applicable Part 68

rules and technical requirements adopted by

ACTA. A compliant telephone cord and modular

plug is provided with this product. It is designed

to be connected to a compatible modular jack

that is also compliant. An RJ11 jack should

normally be used for connecting to a single

line and an RJ14 jack for two lines. See the

installation instructions in the user’s manual.

The Ringer Equivalence Number (REN) is used

to determine how many devices you may connect

to your telephone line and still have them ring

when you are called. The REN for this product is

encoded as the 6th and 7th characters following

the US: in the product identiﬁer (e.g., if ## is 03,

the REN is 0.3). In most, but not all areas, the sum

of all RENs should be ﬁve (5.0) or less. For more

information, please contact your telephone service

provider.

This equipment may not be used with Party

Lines. If you have specially wired alarm dialing

equipment connected to your telephone line,

ensure the connection of this equipment

does not disable your alarm equipment. If you

have questions about what will disable alarm

equipment, consult your telephone service

provider or a qualiﬁed installer.

If this equipment is malfunctioning, it must

be unplugged from the modular jack until the

problem has been corrected. Repairs to this

telephone equipment can only be made by the

manufacturer or its authorized agents. For repair

procedures, follow the instructions outlined

under the Limited warranty.

If this equipment is causing harm to the

telephone network, the telephone service

provider may temporarily discontinue your

telephone service. The telephone service

provider is required to notify you before

interrupting service. If advance notice is not

practical, you will be notiﬁed as soon as

possible. You will be given the opportunity to

correct the problem and the telephone service

provider is required to inform you of your right

to ﬁle a complaint with the FCC. Your telephone

service provider may make changes in its

facilities, equipment, operation, or procedures

that could affect the proper functioning of

this product. The telephone service provider

is required to notify you if such changes are

planned.

If this product is equipped with a corded or

cordless handset, it is hearing aid compatible.

If this product has memory dialing locations,

you may choose to store emergency telephone

numbers (e.g., police, ﬁre, medical) in these

locations. If you do store or test emergency

numbers, please: Remain on the line and brieﬂy

explain the reason for the call before hanging

up.

Perform such activities in off-peak hours, such

as early morning or late evening.

Industry Canada

This device complies with Industry Canada

licence-exempt RSS standard(s).

Operation is subject to the following two

conditions: (1) this device may not cause

harmful interference, and (2) this device must

accept any interference received, including

interference that may cause undesired

operation.

Privacy of communications may not be ensured

when using this telephone.

The term ‘’IC:‘’ before the certiﬁcation/

registration number only signiﬁes that the

Industry Canada technical speciﬁcations were

met.

The Ringer Equivalence Number (REN) for

this terminal equipment is NAN. The REN

is an indication of the maximum number of

devices allowed to be connected to a telephone

interface. The termination on an interface may

consist of any combination of devices subject

only to the requirement that the sum of the

RENs of all the devices does not exceed ﬁve.

Remark: The word “NAN” means “Not

Applicable”.

This product meets the applicable Industry Canada

technical speciﬁcations.

RF radiation exposure statement

The handset complies with FCC RF radiation

exposure limits set forth for an uncontrolled

environment. Use of other accessories may

not ensure compliance with FCC RF exposure

guidelines. This transmitter must not be co-

located or operating in conjunction with any

other antenna or transmitter. This equipment

complies also with Industry Canada RSS-102

with respect to Canada’s Health Code 6 for

Exposure of Humans to RF Fields.

California Energy Commission

battery charging testing instructions

This telephone is set up to comply with the

energy-conserving standards right out of

the box. These instructions are intended

for California Energy Commission (CEC)

compliance testing only. When the CEC battery

charging testing mode is activated, all telephone

functions, except battery charging, will be

disabled.

When ﬁrst purchased and properly installed

for charging (see Install the battery), put the

handset on the charger to charge. The CEC

battery charging testing mode is activated while

charging.

If you have registered the handset to a Careline

series telephone base, below are the testing

instructions.

For SN1157/SN1197/SN6147/SN6196/SN6197

telephone:

To activate the CEC battery charging

testing mode

NOTE

Your telephone base and the corded handset

can still function normally when the CEC battery

charging testing mode is activated.

1. Press and hold FIND HS at the telephone

base until the IN USE light ﬂashes and

the telephone base shows Registering...

Please wait followed by Deregister all

devices?.

2. Immediately press YES or FIND HS

within 5 seconds.

To deactivate the CEC battery charging

testing mode

• Register your handsets back to the

telephone base. Refer to the Add and

Careline series user ’s manual and this

manual.

For SN6127/SN6187 telephone:

To activate the CEC battery charging

testing mode

1. Unplug the telephone base power

adapter from the power outlet. Make

sure all handsets are plugged with

charged batteries before proceeding.

2. While you press and hold

/FIND

HANDSET

, plug the telephone base

power adapter back to the power outlet.

3. After about 20 seconds, when the

IN USE light starts ﬂashing quickly,

release /FIND HANDSET and then

press it again within 5 seconds.

When the phone successfully enters the

CEC battery charging testing mode, the

IN USE light turns off.

NOTES

• When the phone fails to enter this mode, repeat

Step 1 through Step 3 above.

• The telephone base will be powered up as

normal if you fail to press /FIND HANDSET

within 2 seconds in Step 3.

To deactivate the CEC battery charging

testing mode

1. Unplug the telephone base power adapter

from the power outlet, then plug it back in.

Then the telephone base is powered up

as normal.

2. Register your handsets back to the

telephone base. Refer to the Add and

Careline series user’s manual and this

manual.

For C-UL compliance only

Mesures de sécurité importantes

Aﬁn de réduire les risques d’incendie, de

blessures corporelles ou d’électrocution, suivez

toujours ces mesures préventives de base

lorsque vous utilisez votre téléphone :

1. Lisez et comprenez bien toutes les

instructions.

2. Observez toutes les instructions et mises en

garde inscrites sur l’appareil.

3. Débranchez ce téléphone de la prise murale

avant de le nettoyer. N’utilisez pas de

nettoyeurs liquides ni en aérosol. N’utilisez

qu’un chiffon doux et légèrement humecté.

4. N’utilisez pas ce produit près de l’eau, tel

que près d’un bain, d’un lavabo, d’un évier

de cuisine, d’un bac de lavage ou d’une

piscine, ou dans un sous-sol humide ou

sous la douche.

5. Ne déposez pas ce téléphone sur un chariot,

support ou table chancelants. L’appareil

pourrait tomber et être sérieusement

endommagé.

6. Le boîtier de l’appareil est doté de fentes et

d’ouvertures d’aération situées à l’arrière ou

en dessous. Aﬁn d’empêcher la surchauffe,

ces ouvertures ne doivent pas être obstruées

en plaçant l’appareil sur un lit, divan, tapis

ou autre surface similaires. Ne placez pas

cet appareil à proximité d’un élément de

chauffage ni d’une plinthe électrique. De plus,

ne l’installez pas dans une unité murale ou un

cabinet fermé qui ne possède pas d’aération

adéquate.

7. Ne faites fonctionner cet appareil qu’avec le

type d’alimentation indiqué sur les étiquettes

de l’appareil. Si vous ne connaissez pas le

voltage de votre maison, consultez votre

marchand ou votre fournisseur d’électricité.

8. Ne déposez rien sur le cordon

d’alimentation. Installez cet appareil dans un

endroit sécuritaire, là où personne ne pourra

trébucher sur la ligne d’alimentation ni le

cordon téléphonique modulaire.

9. N’insérez jamais d’objets à travers les

fentes et ouvertures de cet appareil, car ils

pourraient toucher à des points de tension

dangereux ou court-circuiter des pièces,

ce qui constituerait un risque d’incendie ou

d’électrocution. N’échappez pas de liquides

dans l’appareil.

10. Aﬁn de réduire les risques d’électrocution,

ne démontez pas l’appareil, mais

apportez-le plutôt à un centre de service

qualiﬁé s’il doit être réparé. En enlevant

le couvercle, vous vous exposez à des

tensions dangereuses ou autres dangers

similaires. Un remontage inadéquat peut

être à l’origine d’une électrocution lors

d’une utilisation ultérieure de l’appareil.

Débranchez l’appareil avant de procéder

au nettoyage. Utilisez un chiffon humide et

doux.

11. Ne surchargez pas les prises de courant et les

rallonges.

12. Débranchez cet appareil de la prise

de courant et communiquez avec le

département de service à la clientèle de

VTech dans les cas suivants :

• Lorsque le cordon d’alimentation est

endommagé ou écorché.

• Si du liquide a été échappé dans

l’appareil.

• Si l’appareil a été exposé à une source

d’humidité telle que la pluie ou l’eau.

• Si le produit ne fonctionne pas

normalement en respectant les

instructions de fonctionnement.

Réglez uniquement les commandes

indiquées dans le les instructions de

fonctionnement. Les réglages incorrects

des autres commandes pourraient

provoquer un dommage qui pourrait

exiger un travail exhaustif de la part d’un

technicien autorisé aﬁn de rétablir le

fonctionnement normal de l’appareil.

• Si le produit a été échappé et que le socle

et/ou le combiné a été endommagé.

• Si le produit afﬁche une nette diminution

de sa performance.

13. Évitez d’utiliser un téléphone (autre qu’un

sans ﬁl) pendant un orage. Les éclairs

peuvent être à l’origine d’une électrocution.

14. N’utilisez pas le téléphone pour rapporter

une fuite de gaz à proximité de la fuite. En

certaines circonstances, une ﬂammèche

pourrait être provoquée lorsque l’adaptateur

est branché à une prise de courant, ou

lorsque le combiné est déposé sur le socle.

Ceci est un événement commun associé à la

fermeture d’un circuit électrique. L’utilisateur

ne devrait pas brancher le téléphone à une

prise de courant, et ne devrait pas déposer le

combiné chargé sur le socle, si le téléphone

se trouve à proximité d’un endroit comportant

des concentrations de gaz inﬂammables,

à moins que la ventilation soit adéquate.

Une ﬂammèche dans un tel endroit pourrait

provoquer un incendie ou une explosion. De

tels environnements peuvent comprendre:

des endroits où l’on utilise de l’oxygène

médical sans ventilation adéquate; des gaz

industriels (dissolvants de nettoyage, des

vapeurs d’essence, etc.); une fuite de gaz

naturel, etc.

15. Ne placez que le combiné de votre

téléphone près de votre oreille lorsqu’en

mode de conversation.

16. Ces adaptateurs ont été conçus pour être

orientés en position verticale ou montés au

sol. Les broches ne sont pas conçues pour

maintenir l’adaptateur en place si celui-ci est

barnché dans une prise au plafond ou sous

une table/ armoire.

CONSERVEZ CES INSTRUCTION S

Pile

• MISE EN GARDE : N’utilisez que la pile

incluse.

• Ne jetez pas la pile au feu. Vériﬁez les

instructions spéciﬁques de mise aux rebus

auprès des autorités locales.

• N’ouvrez pas et ne mutilez pas la pile.

L’électrolyte qui s’en échapperait est corrosif

et pourrait causer des brûlures ou des

blessures aux yeux ou à la peau. L’électrolyte

est toxique si avalé.

• Soyez prudents lorsque vous manipulez les

piles aﬁn d’éviter les courts-circuits provoqués

par des matériaux conducteurs.

• Rechargez la pile incluse avec cet appareil,

selon les instructions et limites spéciﬁées

dans ce guide d’utilisation.

Stimulateurs cardiaques implantés

dans l’organisme

Les simulateurs cardiaques (s’applique uniquement

aux téléphones numériques sans ﬁl) :

L’organisme ‘Wireless Technology Research,

LLC (WTR)’, une ﬁrme de recherche

indépendante, a mené une évaluation

pluridisciplinaire des interférences entre les

téléphones sans ﬁl portatifs et les stimulateurs

cardiaques implantés dans l’organisme.

Appuyée par l’Administration des aliments et

drogues (FDA) des États-Unis, la ﬁrme WTR

recommande aux médecins :

Avis aux détenteurs de stimulateurs cardi-

aques

• Ils doivent tenir le téléphone sans ﬁl à

une distance d’au moins six pouces du

stimulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans

ﬁl directement sur le stimulateur cardiaque,

tel que dans une poche de chemise, lorsque

celui-ci est en marche.

• Ils doivent utiliser le téléphone sans ﬁl en

l’appuyant sur l’oreille qui se trouve dans la

direction opposée au stimulateur cardiaque.

L’étude effectuée par l’organisme WRS n’a

pas identiﬁé de risque pour les détenteurs de

simulateurs cardiaques causés par les gens

qui utilisent un téléphone sans ﬁl à proximité de

ceux-ci.

À propos des téléphones sans l

• Condentialité : Les mêmes

caractéristiques qui constituent des

avantages pour les téléphones sans ﬁl

afﬁchent également des restrictions. Les

appels téléphoniques sont transmis entre

le combiné sans ﬁl et le socle par le biais

d’ondes radio ; il y a donc la possibilité que

vos conversations téléphoniques sans ﬁl

soient interceptées par des équipements de

réception radio se trouvant dans la portée

du combiné sans ﬁl. Pour cette raison, vous

ne devez pas percevoir les communications

téléphoniques sans ﬁl comme étant aussi

conﬁdentielles que celles des téléphones à

cordons.

• Alimentation électrique : Le socle de

ce téléphone sans ﬁl doit être branché à

une prise électrique fonctionnelle. La prise

électrique ne doit pas être contrôlée par un

interrupteur mural. Les appels ne pourront

pas être effectués du combiné sans ﬁl si le

socle est débranché ou mis hors tension ou

si le courant est coupé.

• Possibilité d’interférences aux téléviseurs :

Certains téléphones sans ﬁl fonctionnent

sur des fréquences pouvant causer des

interférences aux téléviseurs et aux

magnétoscopes. Pour réduire ou prévenir de

telles interférences, ne placez pas le socle du

téléphone sans ﬁl près ou sur un téléviseur

ou magnétoscope. S’il y a présence de

parasites, il est conseillé d’éloigner le

téléphone sans ﬁl du téléviseur ou du

magnétoscope aﬁn de réduire possiblement

les interférences.

• Piles rechargeables : Manipulez les piles

avec soin aﬁn de ne pas les cour t-circuiter

avec des bagues, bracelets ou clés. Les

piles ou le conducteur peut surchauffer et

causer des blessures. Respectez la polarité

adéquate entre la pile et le chargeur.

• Les bloc-piles re chargeables à l’hydrure

métallique de nickel : Jetez ces blocs-piles

de manière écologique et sécuritaire. Ne les

incinérez pas et ne les percez pas. Tel que

les autres piles de ce type, elles pourraient

dégager une matière toxique qui peut causer

des blessures corporelles si elles sont

brûlées ou percées.

Limited warranty

What does this limited warranty cover?

The manufacturer of this VTech Product

warrants to the holder of a valid proof of

purchase (“Consumer” or “you”) that the

Product and all accessories provided in the

sales package (“Product”) are free from defects

in material and workmanship, pursuant to the

following terms and conditions, when installed

and used normally and in accordance with the

Product operating instructions. This limited

warranty extends only to the Consumer for

Products purchased and used in the United

States of America and Canada.

What will VTech do if the Product is not free

from defects in materials and workmanship

during the limited warranty period

(“Materially Defective Product”)?

During the limited warranty period, VTech’s

authorized service representative will repair

or replace at VTech’s option, without charge,

a Materially Defective Product. If we repair

the Product, we may use new or refurbished

replacement parts. If we choose to replace

the Product, we may replace it with a new or

refurbished Product of the same or similar

design. We will retain defective parts, modules,

or equipment. Repair or replacement of the

Product, at VTech’s option, is your exclusive

remedy. VTech will return the repaired or

replacement Products to you in working

condition. You should expect the repair or

replacement to take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product

extends for ONE (1) YEAR from the date

of purchase. If VTech repairs or replaces a

Materially Defective Product under the terms of

this limited warranty, this limited warranty also

applies to the repaired or replacement Product

for a period of either (a) 90 days from the date

the repaired or replacement Product is shipped

to you or

(b) the time remaining on the original

one-year warranty; whichever is longer.

What is not covered by this limited

warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse,

accident, shipping or other physical

damage, improper installation, abnormal

operation or handling, neglect, inundation,

ﬁre, water or other liquid intrusion; or

2. Product that has been damaged due

to repair, alteration or modiﬁcation by

anyone other than an authorized service

representative of VTech; or

3. Product to the extent that the problem

experienced is caused by signal conditions,

network reliability, or cable or antenna

systems; or

4. Product to the extent that the problem is

caused by use with non-VTech accessories;

5. Product whose warranty/quality stickers,

product serial number plates or electronic

serial numbers have been removed, altered

or rendered illegible; or

6. Product purchased, used, serviced, or

shipped for repair from outside the United

States of America or Canada, or used

for commercial or institutional purposes

(including but not limited to Products used

for rental purposes); or

7. Product returned without a valid proof of

purchase (see item 2 on the next page); or

8. Charges for installation or set up,

adjustment of customer controls, and

installation or repair of systems outside the

unit.

How do you get warranty service?

NOTE: Before calling for service, please review

the user’s manual - a check of the Product’s

controls and features may save you a service

call.

Except as provided by applicable law, you

assume the risk of loss or damage during

transit and transportation and are responsible

for delivery or handling charges incurred

in the transport of the Product(s) to the

service location. VTech will return repaired or

replaced Product under this limited warranty.

Transportation, delivery or handling charges are

prepaid. VTech assumes no risk for damage

or loss of the Product in transit. If the Product

failure is not covered by this limited warranty, or

proof of purchase does not meet the terms of

this limited warranty, VTech will notify you and

will request that you authorize the cost of repair

prior to any further repair activity. You must pay

for the cost of repair and return shipping costs

for the repair of Products that are not covered

by this limited warranty.

What must you return with the Product to

get warranty service?

1. Return the entire original package and

contents including the Product to the VTech

service location along with a description of

the malfunction or difﬁculty; and

2. Include a “valid proof of purchase” (sales

receipt) identifying the Product purchased

(Product model) and the date of purchase or

receipt; and

3. Provide your name, complete and correct

mailing address, and telephone number.

Other limitations

This warranty is the complete and exclusive

agreement between you and VTech.

It supersedes all other written or oral

communications related to this Product. VTech

provides no other warranties for this Product.

The warranty exclusively describes all of

VTech’s responsibilities regarding the Product.

There are no other express warranties. No

one is authorized to make modiﬁcations to this

limited warranty and you should not rely on any

such modiﬁcation.

State/Provincial Law Rights: This warranty gives

you speciﬁc legal rights, and you may also have

other rights, which vary from state to state or

province to province.

Limitations: Implied warranties, including

those of ﬁtness for a particular purpose and

merchantability (an unwritten warranty that

the Product is ﬁt for ordinary use) are limited

to one year from the date of purchase. Some

states/provinces do not allow limitations on how

long an implied warranty lasts, so the above

limitation may not apply to you. In no event

shall VTech be liable for any indirect, special,

incidental, consequential, or similar damages

(including, but not limited to lost proﬁts or

revenue, inability to use the Product or other

associated equipment, the cost of substitute

equipment, and claims by third parties) resulting

from the use of this Product. Some states/

provinces do not allow the exclusion or limitation

of incidental or consequential damages, so the

above limitation or exclusion may not apply to

you.

Please retain your original sales receipt

as proof of purchase.

Technical specifications

Frequency

control

Crystal controlled PLL synthesizer

Transmit

frequency

1921.536-1928.448 MHz

Channels 5

Nominal

effective

range

Maximum power allowed by

FCC and IC. Actual operating

range may vary according to

environmental conditions at the

time of use.

Power

requirements

Battery:

2.4V 400mAh, Ni-MH battery pack

Power adapter: 6V AC @ 300mA

Using the photo speed dial

handset

Make a call

• Press a photo speed dial key to dial.

-OR-

• Press or , and then a photo

speed dial key to dial.

Answer a call

• Press or .

End a call

• Press or place the handset back in

the charger.

Speakerphone

• During a call, press to switch

between the speakerphone and the

earpiece.

Adjust listening Volume

• During a call, press VOL- or VOL+.

Call waiting

When you subscribe to call waiting service

from your telephone service provider, you

hear an alert tone if there is an incoming

call while you are already on a call.

• Press to put the current call on hold

and take the new call.

• Press at any time to switch back and

forth between calls.

Temporary ringer silence

When the telephone is ringing, you can

temporarily silence the handset ringer

without disconnecting the call. The next

call rings normally at the preset volume.

• Press VOL- or .

Join a call in progress

You can use a maximum of four devices at

a time on a call.

• Press or to join the call.

• To exit the call, press or place the

handset back in the charger. The call

continues until all devices hang up.

Find handset

You can use the Find handset feature

on the telephone base to ﬁnd misplaced

handsets.

• Press a photo speed dial key, , or

to stop paging.

• Press or VOL- to mute the paging

tone.

Deregister handsets

Your telephone system supports a

maximum of 12 devices.

If you have registered 12 devices, and you

want to register a SN6307 handset, you

have to deregister all devices ﬁrst. Then

CAUTION

• Deregister with caution! Once done, all

devices will be deregistered from your

telephone system.

NOTES

• You cannot deregister all devices if any other

system device is in use.

• Even if your devices have run out of battery,

you can still deregister them by following the

instructions in this section.

• To register any cordless handset or pendant

back to the telephone base, refer to the

user’s manual of your Careline series

telephone for details.

VTech SN6307 Manuel utilisateur

Marque: VTech

Modèle: SN6307

Catégorie: Téléphones

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: VTech SN6307 User manual

VTech SN6307 Manuel utilisateur

VTech SN6307 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents