Unbranded RE15416WAVHD1P2 Guide d'installation

RE15416WAVHD1P2
Unbranded
Marque
Unbranded
Modèle
RE15416WAVHD1P2
Taper
Guide d'installation
Prologue Delicate Gray Mosaic & Superior White
12 in. x 18 in. tiles shown in grid and brick pattern
Installation of
COUNTERTOP
& WALL TILE
INSTALLATION INSTRUCTIONS | COUNTERTOP & WALL TILE | PAGE 1 of 5
• Tile may be
installed over most
structurally sound
substrates.
• Make sure surface
is clean, smooth,
dry and free of
wax, soap scum
and grease.
• Any damaged,
loose or uneven
areas must be
repaired, patched
and leveled.
• Remove any
moldings, trim,
appliances or
anything that
could interfere with
installation.
• Find the center point of the wall,
using a level to draw a plumb line
in the wall’s center.
• Lay out a row of loose tiles across
the bottom of the wall from the
center line leaving uniform joints
between tiles.
NOTE: Tiles can be butted together
leaving a consistent 1/16 in. joint
automatically.
TIP: If cuts leave tiles smaller than
half to their original size, adjust
the center line a half tile closer to
the wall.
• Stack two tiles here. At the top,
draw a horizontal line on the wall
and continue the line around all side
walls to be tiled.
STEP 1: SURFACE PREPARATION
1
STEP 2: WALL LAYOUT
2
CONTINUED ON NEXT PAGE
Prologue Delicate Gray Mosaic & Superior White
12 in. x 18 in. tiles shown in grid and brick pattern
Installation of
COUNTERTOP
& WALL TILE
INSTALLATION INSTRUCTIONS | COUNTERTOP & WALL TILE | PAGE 2 of 5
• Mix only enough adhesive
or mortar to be used
within 30 minutes.
• Using the type of trowel
recommended on the
adhesive package, spread
a 1/4 in. coat on the surface
of one grid area, using the
flat side of the trowel.
NOTE: Do not cover
guidelines or a larger
area than can be set
in 15 minutes.
•
Use the notched side of
trowel to comb adhesive into
standing ridges by holding
trowel at a 45° angle.
• Remove excess adhesive,
leaving a uniform, ridged
setting bed.
STEP 4: APPLYING ADHESIVESTEP 3: COUNTERTOP LAYOUT
3 4
• Begin with counter trim, then
set full tiles from the first row
working back thus all cut tiles
will be placed on the back row
against the wall.
NOTE: Trim pieces are
available for use around
recessed appliances.
• S
nap parallel chalk lines on the
substrate as needed to keep
rows straight.
NOTE: Tile countertops should
have a tile backsplash at least
4 inches high for protection.
TIP: For backsplashes, match up
joints with the countertop tile.
CONTINUED ON NEXT PAGE
Prologue Delicate Gray Mosaic & Superior White
12 in. x 18 in. tiles shown in grid and brick pattern
Installation of
COUNTERTOP
& WALL TILE
INSTALLATION INSTRUCTIONS | COUNTERTOP & WALL TILE | PAGE 3 of 5
STEP 6: SETTING TILE
6
• Install tiles in the center, one grid at a
time. Finish each grid before moving to
the next. Start with the first tile in the
corner of the grid and work outward.
Set tiles one at a time using a slight
twisting motion.
NOTE: Don’t slide tiles into place.
• Insert tile spacers, as each tile is set,
or leave equal joints between tiles.
• Fit perimeter tiles in each grid last,
leaving 1/4 in. gap between tile and wall.
• When finished, tap in all tiles with a
rubber mallet or hammer and wood
block, to ensure a good bond and
level plane.
• Remove excess adhesive from joints
with a putty knife, and from tile with a
damp sponge.
• Do not use surface of tiles until they
are set (usually in 24 hours).
STEP 5: CUTTING TILE
5
• Carefully
measure tiles
and mark with
a pencil or
felt-tip pen.
• Make straight
or diagonal
cuts with a
tile cutter,
curved cuts
with a nipper
(chipping
away small
pieces for best
results), and
full-length
curved cuts
with a rod
saw. Smooth
out sharp-cut
edges with a
carborundum
stone.
CONTINUED ON NEXT PAGE
Prologue Delicate Gray Mosaic & Superior White
12 in. x 18 in. tiles shown in grid and brick pattern
Installation of
COUNTERTOP
& WALL TILE
INSTALLATION INSTRUCTIONS | COUNTERTOP & WALL TILE | PAGE 4 of 5
• Using the instructions on the
package, make enough grout to
use in about 30 minutes.
• Remove tile spacers and spread
grout on the tile surface, forcing
down into joints with a rubber
grout float or squeegee.
• Tilt the float at a 45° angle and remove
excess grout from surface immediately
with the edge of float.
• Tilt it at a 90° angle and scrape it
diagonally across tiles.
• Wait 15–20 minutes for grout to set
slightly, then use a damp sponge to clean
grout residue from surface and smooth
the grout joints, rinsing sponge often.
• Let dry until grout is hard and haze
forms on tile surface, then polish
with a soft cloth and wait 72 hours
for heavy use. NOTE: Don’t apply
sealers or polishes for three weeks,
and then only in accordance with
manufacturer’s recommendations.
STEP 7: GROUTING JOINTS
7
STEP 8: INITIAL CLEANING
8
• The complete removal of
grout and construction dirt
after products have been
installed will improve daily
maintenance.
• Clean successfully by
scrubbing the installation
with hot water and a pH
neutral liquid cleaner
(soapless), followed by a
thorough rinsing, then remove
the rinse water with a wet
vacuum or dry toweling.
• If some residue remains,
further cleaning will need to
be done in consultation with
the grout manufacturer.
• For more aggressive
cleaning, scrubbing machines
equipped with nylon pads
or brushes should be used.
Wet vacuuming of the
suspended dirt and grout is
recommended.
Prologue Delicate Gray Mosaic & Superior White
12 in. x 18 in. tiles shown in grid and brick pattern
Installation of
COUNTERTOP
& WALL TILE
INSTALLATION INSTRUCTIONS | COUNTERTOP & WALL TILE | PAGE 5 of 5
Back-butter spreading of a bond coat
to the back of a ceramic tile
before placing the tile to
ensure a strong bond with
the thin-set mortar.
Balanced cuts perimeter tile cut at equal
size and installed on
opposite sides of an area;
also, equally sized cuts on
each side of a miter.
Butt joint
a plain square joint
between two members
with no grout joint.
Grout
a mix used for filling tile
joints, commonly based
of cement.
Mortar a mixture of cement paste
and fine aggregate used to
bond masonry together.
Plumb perpendicular to true level.
Substrate the underlying support for
a ceramic tile installation
GLOSSARY OF TERMS LEGAL
A B
ATTENTION / ATENCIÓN / ATTENTION
Do not dry cut using motorized equipment due to the potential for exposure
to harmful silica dust. Use a wet saw or a score and snap tool when cutting is
necessary during the installation process.
No corte en seco usando equipo motorizado debido a la posibilidad de
exposición a polvo dañino de sílice. En caso de que sea necesario cortar durante
el proceso de instalación, usar una sierra de corte en húmedo o una herramienta
cortadora manual.
Ne pas couper à sec à l’aide d’un équipement motorisé en raison du risque
d’exposition à la poussière de silice nuisible. Utiliser une scie à eau ou un outil à
inciser et rompre lorsqu’il faut couper pendant le processus d’installation.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Unbranded RE15416WAVHD1P2 Guide d'installation

RE15416WAVHD1P2
Unbranded
Marque
Unbranded
Modèle
RE15416WAVHD1P2
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents