User Guide
DTP T DWP 4K D Series
HDMI Transmitters
HDMI and DisplayPort
Twisted Pair Extender Transmitters
68-2762-01 Rev.
C
01 19
Safety Instructions
Safety Instructions • English
WARNING: This symbol, , when used on the product, is intended to
alert the user of the presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of electric shock.
ATTENTION: This symbol, , when used on the product, is intended
to alert the user of important operating and maintenance (servicing)
instructions in the literature provided with the equipment.
For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide, part number 68-290-01, on the Extron
website, www.extron.com.
Sicherheitsanweisungen • Deutsch
WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer
darauf aufmerksam machen, dass im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen herrschen, die nicht isoliert sind und
die einen elektrischen Schlag verursachen können.
VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in
der im Lieferumfang enthaltenen Dokumentation besonders wichtige
Hinweise zur Bedienung und Wartung (Instandhaltung) geben.
Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,
EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in
den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer
68-290-01) auf der Extron-Website, www.extron.com.
Instrucciones de seguridad • Español
ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,
avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del
producto, lo que puede representar un riesgo de descarga eléctrica.
ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa
al usuario de la presencia de importantes instrucciones de uso y
mantenimiento recogidas en la documentación proporcionada con el
equipo.
Para obtener información sobre directrices de seguridad, cumplimiento
de normativas, compatibilidad electromagnética, accesibilidad y temas
relacionados, consulte la Guía de cumplimiento de normativas y seguridad
de Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com.
Instructions de sécurité • Français
AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le
produit, signale à l’utilisateur la présence à l’intérieur du boîtier du
produit d’une tension électrique dangereuse susceptible de provoquer
un choc électrique.
ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit,
signale à l’utilisateur des instructions d’utilisation ou de maintenance
importantes qui se trouvent dans la documentation fournie avec le
matériel.
Pour en savoir plus sur les règles de sécurité, la conformité à la
réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets
connexes, lisez les informations de sécurité et de conformité Extron, réf.
68-290-01, sur le site Extron, www.extron.com.
Istruzioni di sicurezza • Italiano
AVVISO: Questo simbolo, ,quando viene utilizzato il prodotto, serve
ad avvisare l’utente della presenza di tensioni pericolose non isolate
all’interno del prodotto, che può presentare un rischio di scosse
elettriche.
ATTENTZIONE: Questo simbolo, , quando viene utilizzato il
prodotto, serve ad avvisare l’utente di importanti istruzioni di uso e
manutenzione (assistenza) nella letteratura fornita con l’apparecchiatura.
Per informazioni sulle linee guida di sicurezza, adempimenti normativi,
compatibilità EMI/EMF, accessibilità e argomenti correlati, vedere la sicurezza
di Extron e Regulatory Compliance Guide, parte numero
68-290-01, sul sito Web Extron, www.extron.com.
Instrukcje bezpieczeństwa • Polska
OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma na celu
poinformować użytkownika o obecności izolowanego i niebezpiecznego
napięcia wewnątrz obudowy produktu, który może stanowić zagrożenie
porażenia prądem elektrycznym.
UWAGI: Ten symbol, , gdy używany na produkt, jest przeznaczony do
ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji
(obsługi) w literaturze, wyposażone w sprzęt.
Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji
wzajemnej zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne,
zobacz Extron bezpieczeństwa i regulacyjnego zgodności przewodnik, część
numer 68-290-01, na stronie internetowej Extron, www.extron.com.
Инструкция по технике безопасности • Русский
ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан на продукте,
предупреждает пользователя о наличии неизолированного опасного напряжения
внутри корпуса продукта, которое может привести к поражению электрическим
током.
ВНИМАНИЕ: Данный символ, , если указан на продукте,
предупреждает пользователя о наличии важных инструкций
по эксплуатации и обслуживанию в руководстве,
прилагаемом к данному оборудованию.
Для получения информации о правилах техники безопасности,
соблюдении нормативных требований, электромагнитной
совместимости (ЭМП/ЭДС), возможности доступа и других
вопросах см. руководство по безопасности и соблюдению
нормативных требований Extron на сайте Extron: ,
www.extron.com, номер по каталогу - 68-290-01.
安全说明 • 简体中文
警告： 产品上的这个标志意在警告用户该产品机壳内有暴露的危险 电压，
有触电危险。
注意： 产品上的这个标志意在提示用户设备随附的用户手册中有
重要的操作和维护(维修）说明。
关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍
使用的特性等相关内容，敬请访问 Extron 网站 , www.extron.com，参见
Extron 安全规范指南，产品编号 68-290-01
。
安全記事 • 繁體中文
警告: 若產品上使用此符號，是為了提醒使用者，產品機殼內存在著
可能會導致觸電之風險的未絕緣危險電壓。
注意 若產品上使用此符號，是為了提醒使用者，設備隨附的用戶手冊中有
重要的操作和維護（維修）説明。
有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細資
訊，請瀏覽 Extron 網站：www.extron.com，然後參閱《Extron 安全性與法規
遵守手冊》，準則編號 68-290-01。
安全上のご注意
• 日本語
警告: この記号 が製品上に表示されている場合は、筐体内に絶縁されて
いない高電圧が流れ、感電の危険があることを示しています。
注意:この記号 が製品上に表示されている場合は、本機の取扱説明書に
記載されている重要な操作と保守(整備)の指示についてユーザーの注意
を喚起するものです。
安全上のご注意、法規厳守、EMI/EMF適合性、その他の関連項目に
つ い て は 、エ ク スト ロ ン の ウェ ブ サ イト www.extron.com よ り 『 Extron Safety
and Regulatory Compliance Guide』 ( P/N 68-290-01) をご覧ください。
안전 지침 • 한국어
경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는
접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을
경고합니다.
주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와
있는 주요 운영 및 유지보수(정비) 지침을 경고합
니다.
안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에
대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및
규제 준수 안내서, 68-290-01 조항을 참조하십시오.
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause interference. This interference must be corrected at the expense of the user.
ATTENTION: The Twisted Pair Extension technology works with shielded twisted pair
(STP) cables only. To ensure FCC Class A and CE compliance, STP cables and STP
connectors are also required.
For more information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the “Extron Safety and
Regulatory Compliance Guide” on the Extron website.
Copyright
© 2017
-2019 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks
®
, registered service marks
(SM)
, and trademarks
(TM)
are the property of RGB Systems, Inc. or
Extron Electronics (see the current list of trademarks on the Terms of Use page at www.extron.com):
Registered Trademarks
(®)
AVTrac, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Extron, Flat Field, FlexOS, Global Configurator,
GlobalScripter, GlobalViewer, Hideaway, Inline, IPIntercom, IPLink, KeyMinder, LinkLicense, LockIt, MediaLink, MediaPort, NetPA,
PlenumVault, PoleVault, PowerCage, PURE3, Quantum, SoundField, SpeedMount, SpeedSwitch, SystemINTEGRATOR, TeamWork, TouchLink,
V-Lock, VersaTools, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP, and XTPSystems
Registered Service Mark
(SM)
: S3 Service Support Solutions
Trademarks
(
™
)
AAP, AFL (Accu-RateFrameLock), ADSP(Advanced Digital Sync Processing), Auto-Image, CableCover, CDRS(ClassD Ripple Suppression),
DDSP(Digital Display Sync Processing), DMI (DynamicMotionInterpolation), DriverConfigurator, DSPConfigurator, DSVP(Digital
Sync Validation Processing), eLink, EQIP, EverLast, FastBite, FOX, FOXBOX, HyperLane, IP Intercom HelpDesk, MAAP, MicroDigital, Opti-
Torque, ProDSP, QS-FPC(QuickSwitch Front Panel Controller), Room Agent, Scope-Trigger, ShareLink, Show Me, SIS,
SimpleInstructionSet, Skew-Free, SpeedNav, Triple-Action Switching, True4K, Vector™ 4K , WebShare, XTRA, ZipCaddy, and ZipClip
Conventions Used in this Guide
Notifications
The following notifications are used in this guide:
CAUTION: Risk of minor personal injury.
ATTENTION : Risque de blessuremineure.
ATTENTION:
• Risk of property damage.
• Risque de dommages matériels.
NOTE: A note draws attention to important information.
Software Commands
Commands are written in the fonts shown here:
^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C
[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]
E X! *X1&* X2)* X2#* X2! CE}
NOTE: For commands and examples of computer or device responses mentioned
in this guide, the character “0” is used for the number zero and “O” is the capital
letter “o.”
Computer responses and directory paths that do not have variables are written in the font
shown here:
Reply from 208.132.180.48: bytes=32 times=2ms TTL=32
C:\Program Files\Extron
Variables are written in slanted form as shown here:
ping xxx.xxx.xxx.xxx —t
SOH R Data STX Command ETB ETX
Selectable items, such as menu names, menu options, buttons, tabs, and field names are
written in the font shown here:
From the File menu, select New.
Click the OK button.
Specifications Availability
Product specifications are available on the Extron website, www.extron.com.
Extron Glossary of Terms
A glossary of terms is available at http://www.extron.com/technology/glossary.aspx.
viExtron DTP T DWP 4K D Series • Contents
Contents
Introduction............................................................ 1
About this Guide ................................................. 1
About the DTP T DWP 4K D Series .................... 1
Twisted Pair Cable Advantages ....................... 2
Transmission Distance .................................... 2
Features ............................................................. 2
Installation and Operation .................................. 3
Mounting the Transmitter .................................... 3
UL and Safety Guidelines ................................ 3
Site Preparation and Wall Box Installation ....... 4
Mud Ring Installation ...................................... 5
Final Installation .............................................. 6
DTP T DWP 4K D Series
Connections ...................................................... 6
Front Panel ..................................................... 6
Rear Panel ...................................................... 7
Twisted Pair Recommendations for DTP
Communication ................................................. 8
Supported Cables .......................................... 8
Cable Recommendations ............................... 8
Power Supply Wiring .......................................... 9
RS-232 and IR Connector Wiring ..................... 11
Over TP RS-232 and IR Connector ............... 11
Remote RS-232 Connector .......................... 11
Operation ......................................................... 12
Transmitter LEDs .......................................... 12
System Operation ......................................... 12
Audio Configuration ...................................... 13
Remote Control ................................................... 14
Simple Instruction Set Control .......................... 14
Host-to-Extender Communications ............... 14
Transmitter-Initiated Messages ...................... 14
Error Responses ........................................... 15
Timeout ........................................................ 15
EDID ............................................................. 15
TMDS Output Format ................................... 15
DTP T DWP 4K D EDID Memory Locations... 16
Using the Command and Response Table .... 17
Command and Response Table for SIS
Commands ..................................................... 19
Reference Information ...................................... 23
Decorator-Style Wallplate Template
Dimensions ..................................................... 23
Extron DTP T DWP 4K D Series • Introduction 1
Introduction
• About this Guide
• About the DTP T DWP 4K D Series Extenders
• Features
About this Guide
This guide provides instructions for experienced, professional installers to install, operate,
and configure the Extron DTP T DWP 4K D series of High-Definition Multimedia Interface
(HDMI
®
) and DisplayPort
®
Extenders.
Terms Used in this Guide
The terms “extender” and “transmitter” are used interchangeably in this guide to refer to all
of the DTP T DWP 4K D models.
About the DTP T DWP 4K D Series Extenders
The Extron DTP T DWP 4K D extenders are a series of HDMI and DisplayPort transmitters
(see figure 1) that are housed in enclosures that can be mounted in Underwriters
Laboratories (UL) standard wall boxes with decorator-style faceplates. Paired with a
compatible DTP 230 or 330 receiver, they extend the usable distance of HDMI digital video,
DisplayPort digital video, and RS-232 or IR control signals over one shielded twisted pair
(STP) cable. The extenders also route and embed audio.
Figure 1. A Typical Transmitter and Receiver Application
TLP 1000TV
IPCP 505
IN1608
DTP HDMI 230 Rx
Projector
100-240V ~ -- A MAX
1
2
CONFIGURABLE
HDMI
HDMI
5
6
7
8
C
RS-232 IR
RS-232 IR
Tx Rx Tx RxG
Tx Rx Tx RxG
Tx Rx Tx RxG
HDMI
A
B
3
4
INPUTS
OUTPUTS
Tx Rx
RS-232
G
LAN
2x25W(8Ω)/2x50W(4Ω)
RESET
AUDIO INPUTS
OUTPUTS
REMOTE
LL1R R
L2
R
L
3
R
CLASS 2 WIRING
L4
R
L5R
+48V
+48V
12
LR
VARIABLE
IN1608 SA
2
MIC/LINE
L6
R
SIG LINK
DTP IN
SIG LINK
DTP IN
SIG LINK
DTP OUT
50/60 Hz
RS-232 IR
OVER DTP
OVER DTP
OVER DTP
AMPLIFIED OUTPUT
VOLUME
SCALING PRESENTATION SWITCHER
IN1608
INPUTS
1
HDCP
SIGNAL
OUTPUTS
ENTER
MENU
Extron
2 3 4 5 6 7 8 A B C
INPUTS
1 2 3 4 5 6 7 8
CONFIG
AUDIO IN
DP IN
AUDIO IN
HDMI IN
Extron
Extron
DTP T DWP 4K 232 D
Transmit ter
Ethernet
A Typical DTP T HWP 232 D and DTP T UWP 232 D Application
Network
LR
POWER
12V
0.7A MAX
AUDIO
SIG LINK
DTP IN
OUTPUTS
XTP DTP 24 Cable
230' (70m)
XTP DTP 24 Cable
230' (70m)
HDMI
1 2345678
100
LINK
ACT
COM
IR/S
TX
RX
TX
RX
RTS
CTS
R
5
1
6
2
7
3
8
4
RELAY
FLEX
I/O
5
1
6
2
3
1
4
2
eBUS
ACT LIMIT
OVER
SWITCHED
12VDC
3
1
4
OVER
2
LIMIT
IR
7
3
8
4
IPCP 505
Extron DTP T DWP 4K D Series • Introduction 2
DTP T DWP 4K D systems consist of a transmitter (Tx) and a receiver (Rx). The transmitters
and corresponding compatible receivers are sold separately. Each purchased transmitter is
shipped with a single external desktop 12 VDC power supply that accepts 100 to 240 VAC,
50-60 Hz input. A single power supply connected to either the transmitter or a compatible
receiver can power both units through the twisted pair cable that links the units.
Twisted Pair Cable Advantages
Twisted pair cable is much smaller, lighter, more flexible, and less expensive than coaxial,
HDMI, or DisplayPort cable. These transmitter and receiver twisted pair (TP) products make
cable runs simpler and less cumbersome. Termination of the cable with RJ-45 connectors
is simple, quick, and economical (see Twisted Pair Recommendations for DTP
Communication on page 8 for more information).
NOTE: Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201
cable to link the transmitter and receiver. The DTP T DWP 4K 232 D and 332 D do
not work properly with these cables.
Transmission Distance
The maximum transmission distance is determined by the resolution of the signal and the
twisted pair cable, graphics card, and display used in the system.
• DTP T DWP 4K 232 D transmitters can transmit 720p, 1080i or 1080p HDTV video
signals up to 230 feet (70 meters) over STP cable.
• DTP T DWP 4K 332 D transmitters can transmit 720p, 1080i or 1080p HDTV video
signals up to 330 feet (100 meters) over STP cable.
Features
Transmits HDMI and DisplayPort signals over one STP cable — Twisted pair cables
provide an economical, easily installed cable solution.
Supports DDC and HDCP transmission — The transmitters fully support long distance
transmission of the DDC and HDCP signals.
Supports computer and video resolutions up to 4K, including 1080p/60 Deep Color
Control communications pass-through — Bidirectional RS-232 or IR control signals
can be transmitted alongside the HDMI signal, so that the remote display can be controlled
without the need for additional cabling.
Analog stereo audio embedding — Analog stereo audio signals can be selectively
embedded onto the digital video output signal and transported over DTP. The DisplayPort
and HDMI inputs can be set to pass the embedded digital audio, embed the analog audio,
or to automatically embed the analog audio when no digital audio is detected.
External 100 VAC to 240 VAC, 50-60 Hz, international power supply — Included with
transmitters.
Remote powering of the transmitter or receiver — For simplified installation, the
transmitter can be remotely powered by a DTP-enabled product over the twisted pair
connection.
Extron DTP T DWP 4K D Series • Installation and Operation 3
Installation and
Operation
This section describes the installation and the operation of the extenders, including:
• Mounting the Transmitter
• DTP T DWP 4K D Series Connections
• Twisted Pair Recommendations for DTP Communication
• Power Supply Wiring
• RS-232 and IR Connector Wiring
• Operation
Mounting the Transmitter
ATTENTION:
• Installation and service must be performed by authorized personnel.
• L’installation et l’entretien doivent être effectués par le personnel autorisé
uniquement.
• The unit must be installed in accordance with the National Electrical Code and with
local electrical and safety codes.
• L’unité doit être installée conformément au National Electric Code et aux normes
électriques et de sécurité locales.
The transmitters can be installed in a two-gang electrical wall box, or with a mud ring with a
decorator-style wallplate cover (supplied).
UL and Safety Guidelines
The following UL guidelines pertain to the installation of the decorator-style wallplate
transmitters into a wall or furniture.
• These units are not to be connected to a centralized DC power source or used beyond
their rated voltage range.
• These units must be installed in UL listed wall boxes.
• These units must be installed with conduit in accordance with National Electrical Code.
Extron DTP T DWP 4K D Series • Installation and Operation 4
Site Preparation and Wall Box Installation
Choose a location that allows cable runs without interference. Allow enough depth for both
the wall box and the cables. Install the cables into the wall, furniture, or conduits before
installing the wallplate.
NOTE: The extender units are very deep and have connectors on the back side. Extron
recommends a 2-gang wall box which has a depth of at least 3.0 inches (7.6 cm) to
accommodate the connectors and cables.
To install a new wall box, perform steps 1 through 9. If a suitable wall box is already
installed, perform steps 6 through 9 on the next page. UL Listed wall boxes are
recommended.
1. If a wall box is not available to use for a template, use the dimensions on the
Decorator-Style Wallplate Template Dimensions on page 23 to create a template.
If installing directly into furniture, cut out the center portion of the template. To download
a printable template, go to www.extron.com.
2. Place the wall box (or the full size template) against the installation surface, and mark
the opening guidelines.
3. Cut out the material from the marked area.
4. Insert the wall box into the opening. The rear connectors on the box or wallplate should
fit easily into the opening. Enlarge or smooth the edges of the opening if needed.
5. Secure the wall box with nails or screws, leaving the front edge flush with the outer wall
or furniture surface (see figure 2).
NOTES:
• If attaching the wall box to wood, use four #8 or #10 screws or 10-penny
nails. A minimum of 0.5 inch (1.3 cm) of screw thread must penetrate the
wood.
• If attaching the wall box to metal studs or furniture, use four #8 or #10
self-tapping sheet metal screws or machine bolts with matching nuts.
Extron
DTP T DWP 4K 332 D
Signal Output
Cable
Cable
Clamp
Decorator-Style Faceplate
Screws or
Nails
W
all opening is
flush with edge of box.
Wall Stud
AUTO SW
CONFIG
HDMI IN
AUDIO IN
HDBT
DTP
HDCP
1
AUDIO IN
DP IN
Figure 2. Installing the Wall Box and Mounting the Unit
Extron DTP T DWP 4K D Series • Installation and Operation 5
6. Feed the twisted pair cables and, if applicable, the power cables through the opening
and through the wall box punch-out holes, securing them with cable clamps to provide
strain relief.
NOTES:
• In order to fit in the wall box, the twisted pair cables and RJ-45 connectors
should not have a boot installed.
• One power supply can power both the transmitter and the receiver, so only
one unit needs a power supply (see Power Supply Wiring on page 9).
7. Trim back and insulate exposed cable shields with heat shrink to reduce the chance of
short circuits.
To prevent short circuits, the outer foil shield can be cut back to the point where the
cable exits the cable clamp.
8. Screw the included grounding strap to the ground point on the rear of the unit. Wrap
the opposite end of the grounding strap to a grounded point on the junction box or a
ground box.
9. Connect the cables to the rear of the unit (see figure 5 on page 7 for connector details).
10. Connect front panel devices (see Front Panel on the next page for connector details)
and follow the steps in Final Installation on the next page.
Mud Ring Installation
1. Using the mud ring as a guide, mark the edges and cut out the material within the
marked area.
2. Insert the mud ring into the opening, rotate and secure the locking arms with the
supplied screws shown in figure 3.
3. Follow steps 6 through 9 above, and Final Installation on the next page.
Wall Mounting
Mudring
Wall
Figure 3. Installing the Mud Ring
Extron DTP T DWP 4K D Series • Installation and Operation 6
Final Installation
After testing and making any adjustments, do the following:
1. At the power outlet, unplug the power supply.
NOTE: One power supply can power both the transmitter and the receiver (see
Power Supply Wiring on page 9).
2. Mount the transmitter into the wall box or mud ring and attach the supplied decorator-
style faceplate to the unit (see figure 2 on page 4).
3. At the power outlet, reconnect the power supply. This powers up both units.
DTP T DWP 4K D Series Connections
Front Panel
AUDIO IN
AUTO SW
HDCP
1
2
CONFIG
HDMI IN
AUDIO IN
DP IN
Extron
A
B
C
A
D
HDBT
DTP
E
Figure 4. DTP T DWP 4K D Series Front Panel Connectors and Side Panel
A Audio input connector — Connect an unbalanced stereo
audio source to this 3.5 mm mini stereo jack. The image to the
right shows how to wire the audio plug.
B HDMI input connector — Connect an HDMI cable between
this port and the HDMI output port of the digital video source.
C DisplayPort input connector — Connect a DisplayPort cable between this port and
the DisplayPort output port of the digital video source.
D Mini USB port — Connect a male USB mini-B cable to this port for SIS configuration
and firmware updates.
E DTP/HDBaseT switch — Set this 2-position, recessed switch to configure the output
between HDBaseT and DTP modes. When configured for HDBaseT, use an HDBaseT-
compatible receiving device. When configured for DTP, use a DTP-compatible receiving
device.
NOTES:
• In DTP mode, A single power supply connected to either a transmitter or
compatible receiver can power both units.
• When the switch is set to HDBaseT mode, remote power is disabled and
power supplies are required for both transmitter and receiver. Analog audio is
enabled, but incompatible with third-party HDBaseT devices.
Sleeve ( )
Ring
Right (
-
)
Tip
Left (+)
Extron DTP T DWP 4K D Series • Installation and Operation 7
Rear Panel
POWER
12V
1.1 A MAX
DTP T DWP 4K 232 D
RS-232 RS-232 SIG LINK
Tx Rx Tx Rx G Tx Rx G
IR
RESET
OVER TP REMOTE
OUT
F
A
B
C
D
DTP T DWP 4K D Rear Panel
E
Figure 5. DTP T DWP 4K D Series Rear Panel Connectors
A DC power input connector — Plug the included external 12 VDC power supply into
either this 2-pole connector (see Power Supply Wiring on page 9 to wire the power
connector) or the power input connector on the receiver (see the user guide of your
receiver for more information).
B Over TP control port — Connect an RS-232, IR, or both devices to this 5-pole,
3.5 mm captive screw connector for pass-through RS-232 or IR control (see RS-232
and IR Connector Wiring on page 11 to properly wire the RS-232 connector).
C Remote (RS-232) control port — Connect an RS-232 device to this 3-pole, 3.5 mm
captive screw connector for SIS configuration and firmware updates (see RS-232 and
IR Connector Wiring on page 11 to properly wire the Remote connector).
• RS-232 — To control the unit through this port, connect an RS-232 device and
configure it as follows: 9600 baud rate, 8 data bits, 1 stop bit, no parity.
• IR — Bidirectional TTL level (0 to 5 V) modulated infrared from 30 kHz to 60 kHz.
D Ground point — Use the included grounding strap to ground the unit (see Site
Preparation and Wall Box Installation on page 4 for more information).
E DTP Out port — Connect one end of the twisted pair cable to the RJ-45 connector on
the transmitter (see Twisted Pair Recommendations for DTP Communication on
page 8 to properly wire the RJ-45 connectors). Connect the opposite end of the cable
to the appropriate receiving device.
ATTENTION:
• Do not connect these outputs to a telecommunications or computer data
network.
• Ne connectez pas ces appareils à des données informatiques ou à un réseau
de télécommunications.
F Reset button — Use a small screwdriver to press and hold the recessed button for 6
seconds while the extender is running to perform a factory reset.
Extron DTP T DWP 4K D Series • Installation and Operation 8
Twisted Pair Recommendations for DTP Communication
Use the following pin configurations for shielded twisted pair cables.
5
Pin
1
2
3
6
7
8
4
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
Blue
TIA/EIA
T568-B
TP Wires
12345678
Pins:
Figure 6. Twisted Pair Cable Configuration
Supported Cables
The extenders are compatible with shielded twisted pair cable (F/UTP, SF/UTP, and S/FTP).
ATTENTION:
• Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201
cable to link the device with DTP transmitters or receivers.
• N’utilisez pas le câble AV Skew-FreeUTP version améliorée UTP23SF d’Extron ou
le câble STP201 pour relier le appareil avec les émetteurs ou les récepteurs DTP.
Cable Recommendations
Extron recommends using the following practices to achieve full transmission distances and
reduce transmission errors.
• Use the following Extron XTP DTP 24 SF/UTP cables and connectors for the best
performance:
• XTP DTP 24/1000 Non-Plenum 1000’ (305 m) spool 22-236-03
• XTP DTP 24P/1000 Plenum 1000’ (305 m) spool 22-235-03
• XTP DTP 24 Plug Package of 10 101-005-02
• If not using XTP DTP 24 cable, at a minimum, Extron recommends 24 AWG, solid
conductor, STP cable with a minimum bandwidth of 400 MHz.
• Terminate cables with shielded connectors to the TIA/EIA-T568B standard.
• Limit the use of more than two pass-through points, which may include patch points,
punch down connectors, couplers, and power injectors. If these pass-through points
are required, use shielded couplers and punch down connectors.
NOTE: When using shielded twisted pair cable in bundles or conduits, consider the
following:
• Do not exceed 40% fill capacity in conduits.
• Do not comb the cable for the first 20 meters, where cables are straightened,
aligned, and secured in tight bundles.
• Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners.
• Separate twisted pair cables from AC power cables.
Extron DTP T DWP 4K D Series • Installation and Operation 9
Power Supply Wiring
NOTES:
• Only one power supply is required. A single power supply connected to either unit
in the pair powers both units.
• A power supply is included with each individually-packaged transmitter.
• Do not tin the power supply leads before installing them in the direct insertion
connector. Tinned wires are not as secure in the connectors and could be pulled
out.
Figure 10 shows how to wire the connector.
SECTION A–A
AA
Power Supply
Captive Screw
Ridges
Smooth
3/16"
(5 mm) Max.
Connector
Output Cord
Figure 7. Power Connector Wiring
CAUTION: The wires must be kept separate while the power supply is plugged in.
Remove power before wiring.
ATTENTION : Les deux cordons d’alimentation doivent être tenus à l’écart l’un de
l’autre quand l’alimentation est branchée. Couper l’alimentation avant de faire
l’installation électrique.
Extron DTP T DWP 4K D Series • Installation and Operation 10
ATTENTION:
• Always use a power supply supplied and or specified by Extron. Use of an
unauthorized power supply voids all regulatory compliance certification and may
cause damage to the supply and the end product.
• Utilisez toujours une source d’alimentation fournie ou recommandée par Extron.
L’utilisation d’une source d’alimentation non autorisée annule toute conformité
réglementaire et peut endommager la source d’alimentation ainsi que le produit
final.
• If not provided with a power supply, this product is intended to be supplied by a
power source marked “Class 2” or “LPS” and rated at 12 VDC and a minimum of
1.0 A.
• Si ce produit ne dispose pas de sa propre source d’alimentation électrique, il doit
être alimenté par une source d’alimentation de classe 2 ou LPS et paramétré à
12 V et 1.0 A minimum.
• The installation must always be in accordance with the applicable provisions of
National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical
Code part 1, section 16. The power supply shall not be permanently fixed to
building structure or similar structure.
• Cette installation doit toujours être en accord avec les mesures qui s’applique
au National Electrical Code ANSI/NFPA70, article725, et au Canadian Electrical
Code, partie1, section16. La source d’alimentation ne devra pas être fixée de
façon permanente à une structure de bâtiment ou à une structure similaire.
• Power supply voltage polarity is critical. Incorrect voltage polarity can damage
the power supply and the unit. The ridges on the side of the cord (see figure 7 on
previous page) identify the power cord negative lead.
• La polarité de la source d’alimentation est primordiale. Une polarité incorrecte
pourrait endommager la source d’alimentation et l’unité. Les stries sur le côté
du cordon permettent de repérer le pôle négatif du cordon d’alimentation voir
l’illustration 7.
• To verify the polarity before connection, plug in the power supply with no load and
check the output with a voltmeter.
• Pour vérifier la polarité avant la connexion, brancher l’alimentation hors charge et
mesurer sa sortie avec un voltmètre.
• The length of the exposed (stripped) copper wires is important.
The ideal length is 3/16 inch (5 mm). Longer bare wires can short together.
Shorter wires are not as secure in the connectors and could be pulled out.
• La longueur des câbles exposés est primordiale lorsque l’on entreprend de les
dénuder. La longueur idéale est de 5mm (3/16inches). S’ils sont un peu plus
longs, les câbles exposés pourraient se toucher et provoquer un court circuit. S’ils
sont un peu plus courts, ils pourraient sortir, même s’ils sont attachés par les vis
captives.
• Unless otherwise stated, the AC/DC adapters are not suitable for use in air
handling spaces or in wall cavities.
• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une
utilisation dans les espaces d’aération ou dans les cavités murales.
Extron DTP T DWP 4K D Series • Installation and Operation 11
RS-232 and IR Connector Wiring
Over TP RS-232 and IR Connector
Wire the rear Over TP RS-232/IR connector as shown in figure 8.
Ground
Transmit pin on connected uni
t
Receive pin on connected unit
Connected RS-232 and
IR Device Pins
Transmit pin for IR control
Receive pin for IR control
RxTx
RS-232
IR
RxTx
G
OVER TP
Figure 8. Over TP Connector Wiring
NOTE: Do not tin the wires before installing them in the direct insertion connector.
Tinned wires are not as secure in the connectors and could be pulled out.
Remote RS-232
Wire the rear Remote RS-232 connector as shown in figure 9.
Tx Rx G
RS-232
Ground
Tr
ansmit pin on connected unit
Receive pin on connected unit
Figure 9. Remote RS-232 Connector Wiring
Extron DTP T DWP 4K D Series • Installation and Operation 12
Operation
AUDIO IN
AUTO SW
HDCP
1
2
CONFIG
HDMI IN
AUDIO IN
DP IN
Extron
A
A
B
C
DTP T DWP 4K D Front Panel
Figure 10. Transmitter LED Indicators
Transmitter LEDs
A Power LEDs — Two-color front panel LEDs on the transmitters light to indicate signal
and power status as follows:
• Amber — The unit is receiving power but there is no signal on the associated input.
• Green — The unit is receiving power and a signal is present on the associated
input.
NOTE: Both inputs on the transmitters have their own separate LEDs.
B Auto Switch LED — Lights steadily when auto switch is active.
C HDCP LEDs — Light steadily when HDMI (LED 1) or DisplayPort (LED 2) input has
been authenticated on the source device.
System Operation
After the transmitter, the receiver, and their connected devices are powered up, the system
is fully operational. If any problems are encountered, ensure all cables are routed and
connected properly.
NOTES:
• Ensure that the video source and display are properly connected to the transmitter
and receiver pair, and that the transmitter, the receiver, and the display have power
applied before power is applied to the video source. If all other devices are not
turned on before the video source, the image may not appear.
• Input switching can be performed only via auto switching, RS-232, or IR through
the rear panel connectors.
Extron DTP T DWP 4K D Series • Installation and Operation 13
Audio Configuration
The DTP T DWP 4K D series of products can embed analog audio inputs onto the digital
video output.
NOTE: If no HDMI or DisplayPort signal is present, analog audio is transported over
the DTP connection to the analog audio output of the receiver.
When an input is selected, audio transport over HDMI or DisplayPort can be configured to
operate in one of three modes. Each input can be configured individually for any of the three
modes.
• Transport digital embedded audio (default) — The digital embedded audio content
on the digital video input is transported. Analog audio is still separate from the digital
embedded audio on the HDMI or DisplayPort signal and transported simultaneously
over the DTP output, not embedded onto the digital output.
• Embed analog audio input — The analog audio input is always embedded to the
digital output, replacing whatever content is already present on the digital embedded
audio. Analog audio is also transported over the DTP output as a simultaneous output.
• Auto select between analog audio and digital embedded audio — When
both analog audio and digital embedded audio on HDMI or DisplayPort are present,
embedded digital audio on the HDMI or DisplayPort signal takes priority. Analog audio
is transported simultaneously with the digital embedded audio content that is already
present on the DTP output.
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
Extron DTP T DWP 4K D Series Manuel utilisateur
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
Extron DTP HDMI 4K 330 D Rx Manuel utilisateur
-
-
Extron DTP T DP 4K 330 Manuel utilisateur
-
-
-
-
Extron Extender Plus Manuel utilisateur
-
-
-