Sony KD-43X7000G Le manuel du propriétaire

Taper
Le manuel du propriétaire

Ce manuel convient également à

D-520-100-11(1)
SU-WL450
Wall-Mount
Bracket
Installation Information
GB
⫭堩ὅ⿓
CS
⫭塁尫奮
CT
Thông tin Lắp đặt
VN
Informations d’installation
FR
Информация об установке
RU

TH
Informasi Pemasangan
ID
− 2 (GB) −
Installation Information for
Using Sony Wall-Mount Bracket (SU-WL450)
Supported models:
KD-65X70*G / 55X70*G / 49X70*G / 43X70*G
* In the actual model names, the  indicates numbers and/or characters specific to each model.
To Customers
For product protection and safety reasons, Sony strongly recommends that installation of your TV
be performed by Sony dealers or licensed contractors. Do not attempt to install it yourself.
To Sony Dealers and Contractors
Provide full attention to safety during the installation, periodic maintenance and examination of this
product.
Sufficient expertise is required for installing this product, especially to determine the
strength of the wall for withstanding the TV’s weight. Be sure to entrust the attachment
of this product to the wall to Sony dealers or licensed contractors and pay adequate
attention to safety during the installation. Sony is not liable for any damage or injury
caused by mishandling or improper installation.
For Safety and proper installation, follow the Wall-mount Bracket Operation Instructions, TV Setup
Guide and the directions in this manual.
− 3 (GB) −
GB
On Safety
Thank you for purchasing this product.
To Customers
Sufficient expertise is required for
installing this product. Be sure to
subcontract the installation to Sony
dealers or licensed contractors and pay
special attention to safety during the
installation. Sony is not liable for any
damages or injury caused by
mishandling or improper installation, or
installing any other than the specified
product. Your Statutory Rights (if any) are
not affected.
To Sony dealers
Sufficient expertise is required for
installing this product. Be sure to read
this instruction manual thoroughly to do
the installation work safely. Sony is not
liable for any damages or injury caused
by mishandling or improper installation.
Please give this manual to the customer
after installation.
This instruction manual shows the correct
handling of the product and important
precautions necessary to prevent accidents.
Be sure to read this manual thoroughly and
use the product correctly. Keep this manual
available for future reference.
Products by Sony are designed with safety in
mind. If the products are used incorrectly,
however, it may result in a serious injury
through fire, electric shock, the product
toppling over, or the product dropping. Be
sure to observe the precautions for safety to
prevent such accidents.
CAUTION
Specified products
This Wall-Mount Bracket is designed for use
with the products specified TVs. For TVs,
refer to their Reference Guide to verify that
the Wall-Mount Bracket can be used.
To Customers
WARNING
If the following precautions are not
observed, serious injury or death
through fire, electric shock, or the
product dropping can result.
Be sure to subcontract
the installation to
licensed contractors and
keep small children away
during the installation.
If the Wall-Mount Bracket or the TV is not
installed correctly, the following accidents
may occur. Be sure licensed contractors carry
out installation.

The TV may fall and cause a serious injury
such as a bruise or a fracture.

If the wall on which the Wall-Mount
Bracket is installed is unstable, uneven, or
not perpendicular to the floor, the unit
may fall and cause injury or property
damage. The wall should be capable of
supporting a weight of at least four times
the TV weight.
(Refer to your TV’s Reference Guide for its
weight.)

If the installation of the Wall-Mount
Bracket on the wall is not sufficiently
sturdy, the unit may fall and cause injury or
property damage.
Be sure to subcontract
moving or dismounting
of the TV to licensed
contractors.
If persons other than licensed contractors
transport or dismount the TV, it may fall and
cause injury or property damage. Be sure
that two or more persons (three or more
persons for 75 inches and above TV set) carry
or dismount the TV.
Do not remove screws,
etc., after mounting the
TV.
If you do so, the TV may fall and cause injury
or property damage.
Do not make alterations
to the parts of the Wall-
Mount Bracket.
If you do so, the Wall-Mount Bracket may fall
and cause injury or property damage.
Do not mount any
equipment other than
the specified product.
This Wall-Mount Bracket is designed for use
with the specified product only. If you mount
equipment other than specified, it may fall or
break, and cause injury or property damage.
Do not apply any load
other than the TV on the
Wall-Mount Bracket.
Do not shake the TV left/
right, up/down.
If you do so, the TV may fall and cause injury
or property damage.
Do not lean on or hang
from the TV.
Do not lean on or hang from the TV as it may
fall on you and cause serious injury.
CAUTION
If the following precautions are not
observed, injury or property damage
may occur.
Do not handle the
product with excessive
force during cleaning or
maintenance.
Do not apply excessive force on the topside
of the TV. If you do so, the TV may fall and
cause injury or property damage.
Precautions

If you use the TV installed on the
Wall-Mount Bracket for a long time, the
wall behind or above the TV may become
discolored or the wallpaper may come
unstuck, depending on the material of the
wall.

If the Wall-Mount Bracket is removed after
installing it on the wall, the screw holes are
left.

Do not use the Wall-Mount Bracket in a
place where it is subjected to mechanical
vibrations.
Installing the Wall-
Mount Bracket
To Sony Dealers
WARNING
The following instructions are for Sony
dealers only. Be sure to read safety
precautions described above and pay
special attention to safety during the
installation, maintenance and checking
of this product.
Do not install the Wall-
Mount Bracket on wall
surfaces where the
corners or the sides of
the TV protrude away
from the wall surface.
− 4 (GB) −
Do not install the Wall-Mount Bracket on wall
surfaces such as a pillar, where the corners
or the sides of the TV protrude away from
the wall surface. If a person or object
happens to hit the protruded corner or side
of the TV, it may cause injury or property
damage.
Do not install the TV over
or under an air-
conditioner.
If the TV is exposed to water leaks or air
current from an air conditioner for a long
time, it may cause a fire, an electric shock or
a malfunction of the TV.
Be sure to install the
Wall-Mount Bracket
securely to the wall
following the instructions
in this instruction
manual.
If any of the screws are loose or fall out, the
Wall-Mount Bracket may fall and cause injury
or property damage. Be sure to use the
appropriate screws for the material of the
wall and install the unit securely using four
or more screws of 8 mm diameter (or
equivalent).
Be sure to use the
supplied screws and
attachment parts
properly following the
instructions given in
this instruction
manual. If you use
substitute items, the
TV may fall and cause
bodily injury to
someone or damage to
the TV.
Be sure to assemble the
bracket properly
following the instructed
procedure explained in
this instruction manual.
If any of the screws are loose or fall out, the
TV may fall and cause bodily injury to
someone or damage to the TV.
Be sure to tighten the
screws securely in the
designated position.
If you fail to do so, the TV may fall and cause
bodily injury to someone or damage to the
TV.
Be careful not to subject
the TV to shock during
installation.
If the TV is exposed to shock, it may fall or
break apart. This may cause injury.
Be sure to install the TV
on a wall that is both
perpendicular and flat.
If you fail to do so, the TV may fall and cause
injury.
After proper installation
of the TV, secure the
cables properly.
If people or objects get tangled with cables,
this may result in injury or damage to the TV.
Do not allow the AC
power cord (mains lead)
or the connecting cable
to be pinched.
If the AC power cord (mains lead) or the
connecting cable is pinched between the
unit and the wall or is bent or twisted by
force, the internal conductors may become
exposed and cause a short circuit or an
electrical break. This may cause a fire or an
electric shock.
The screws needed to
secure the Wall-Mount
Bracket to the wall are
not supplied.
Use the appropriate screws for the wall
material and structure when mounting the
Wall-Mount Bracket.
− 5 (GB) −
GB
Installing the TV onto the
wall
Installation procedure differs, depending on
your TV.
Use the Wall-Mount Bracket SU-WL450 to
install the TV to the wall.
Note
If the Table-Top Stand is attached to the TV, detach the
Table-Top Stand beforehand. See the Setup Guide and
follow in reverse order the steps to detach the Table-Top
Stand.
Place the TV with its screen facing down on a level and
stable surface covered with a thick and soft cloth, when
securing the Attachment parts for Wall-Mount Bracket or
when removing the Table-Top Stand from the TV to
prevent damaging the surface of the LCD display.
Be sure to store the removed screws in a safe place,
keeping them away from children.
Preparing for installation
Have the TV’s Reference Guide and Setup
Guide at hand before installation.
Be sure to have a Phillips screwdriver that
fits the screws prior to the assembly.
Confirm the installing position of your TV.
Prepare four or more screws of 8 mm
diameter and one screw of 5 mm or
equivalent (not supplied). Select screws
suitable for the material of the wall.
Checking the parts
Supplied with SU-WL450
Verify that all the parts are included.
Base (20) (1) Pulley (2)
PSW 6x20 (4) PSW 4x20 with
Bush (2)
Spacer (20) (2) Belt (1)
Bush (20) (M4) (2) PSW 4x20 (2)
Base Adaptor (2) PSW 4x10 (8)
Spacer (60) (2) PSW 6x50 (2)
Bush (M4) (2) PSW 4x50 (2)
− 6 (GB) −
Deciding on the installation location
1 Decide on the installation location.
Make sure that the wall has enough space for the TV and is capable of supporting a weight of at
least four times that of the TV.
Refer to the following table on installing the TV to the wall. Refer to your TV’s Reference Guide
for the TV's weight.
Standard
mounting
Slim
mounting
Screen centre point
80
Unit: mm
Model Name
Display dimensions
Screen
centre
dimension
Length for mounting
Standard
mounting
Slim
mounting
KD-65X70G
1,463 845 173 597 142 100
KD-55X70G
1,241 721 95 460 141 100
KD-49X70G
1,101 645 -15* 314 119 78
KD-43X70G
970 570 23 315 119 77
*Bracket positioning is below the screen centre point.
Note
Figures in the table may differ slightly depending on the installation.
When your TV is installed on the wall, the upper side of the TV slightly leans forward.
− 7 (GB) −
GB
Allow for suitable clearance between the
TV and the ceiling and protruding parts of
the wall as shown below.
Unit: mm
300100
100 100
To ensure proper ventilation and prevent the
collection of dirt or dust:
ˋ Do not lay the TV set flat, install upside down,
backwards, or sideways.
ˋ Do not place the TV set on a shelf, rug, bed or in a
closet.
ˋ Do not cover the TV set with a cloth, such as
curtains, or items such as newspapers, etc.
ˋ Do not install the TV set as shown below.
Air circulation is blocked.
Wall
Note
If you intend to route the cables in the wall, make a
hole in the wall to insert the cables before beginning
the installation.
To prevent pinching the cables, prepare a hole in the
wall somewhere outside the perimeter of the Base
(20) , Base Adaptor and Spacer (20) , Spacer
(60) .
2 Select Wall mounting style. It is
selectable as shown below.
2-a Standard mount
2-b Slim mount
Refer to the table of step 1.
WARNING
When 2-b is selected, rear terminal access is limited.
2-a 2-b
3 Refer to the below table about
the Base Adaptor fitting
location. In case of selecting
2-b, then skip this step.
Model Name Hook location
KD-65X70G
b
KD-55X70G /
49X70G
c
KD-43X70G
d
a
d
b
c
− 8 (GB) −
Fit Base Adaptor by using
Screw (PSW 4x10) to Base
(20) when selecting 2-a.
4 Decide the positions of the
screws for installing the Base
(20) .
Refer to the specifications on page 13.
When selecting 2-a, please use the hole
positions of Base Adaptor .
WARNING
The wall that the TV will be mounted on should be
able to support a weight of at least four times that of
the TV (Refer to your TV’s Reference Guide for its
weight.).
Determine the strength of the wall the TV will be
mounted on. Reinforce the wall sufficiently, if
necessary.
Installing the Base on the
wall
Use four or more screws of 8 mm diameter
or equivalent (not supplied).

Fit four screws to the holes of Base
Adaptor with Base (20) (2-a only).
Install the Base (20) on the wall
horizontally.
Standard mounting (2-a)
Slim mounting (2-b)
− 9 (GB) −
GB
Preparing for the installation
of the TV
Refer to the Setup Guide for stand installation.
1 Detach the Table-Top Stand
from the TV.
KD-49X70G / 43X70G
Soft cloth
Note
Make sure to place TV on the place where you put a
soft cloth on to prevent damaging display’s surface.
When installing the Wall-Mount Bracket, do not use
the screws removed from the Table-Top Stand.
Be sure to store the removed Table-top Stand and its
screws in a safe place, keeping them away from
children. You will need them if you want to use the TV
on a table in the future. The Table-Top Stand cannot
be purchased separately.
WARNING
Be sure the TV is on the vertical position before
switching on. TV set must not powered on with LCD
panel face down to avoid uneven picture uniformity.
If pressure or shock is applied to the surface of the
TV, the TV may break or become damaged.
Lay the TV face down on a stable and level surface
with the Table-Top Stand hanging over the edge of
the surface. Having the TV face and the base of the
Table-Top Stand on the same level surface will create
an unstable working condition and can damage the
TV.
When detaching the Table-Top Stand from the TV,
hold the Table-Top Stand securely.
2 Attach the Attachment parts for
Wall-Mount Bracket. Check the
Attachment parts by referring to
“Supplied with SU-WL450” in
“Checking the parts” on page
5.
Note
Firmly secure the Attachment parts using screws.
When using an electric screwdriver, set the torque
setting to approximately 1.5 N·m {15 kgf·cm}.
Be sure to store the used or unused parts in a safe
place for future use. Retain this manual for future
reference.
Standard mounting (2-a)
KD-65X70G
Belt
Spacer
(60 mm)
Screw
(+PSW 6 x 50)
Pulley
Screw
(+PSW 6 x 20)
KD-55X70G
Spacer
(60 mm)
Screw
(+PSW 6 x 50)
Pulley
Screw
(+PSW 6 x 20)
Belt
KD-49X70G / 43X70G
Belt
Spacer
(60 mm)
Screw
(+PSW 6 x 50)
Pulley
Screw
(+PSW 6 x 20)
Soft cloth
Slim mounting (2-b)
Note
You cannot use some of the terminals on the rear of
the TV when using this mounting style.
− 10 (GB) −
KD-65X70G
Belt
Spacer
(20 mm)
Screw
(+PSW 6 x 20)
Pulley
Screw
(+PSW 6 x 20)
KD-55X70G
Spacer
(20 mm)
Screw
(+PSW 6 x 20)
Pulley
Screw
(+PSW 6 x 20)
Belt
KD-49X70G / 43X70G
Belt
Spacer
(20 mm)
Screw
(+PSW 6 x 20)
Pulley
Screw
(+PSW 6 x 20)
Soft cloth
3 Connect the necessary cable(s)
to the TV.
Make sure to connect the cables before
installing the TV on the wall. You will be
unable to connect the cables when the TV
is installed.
Refer to the Reference Guide supplied with
your TV.
Note
Subcontract the cable routing in the wall to a licensed
contractor.
Bundle the connecting cables to prevent stepping on
them before wall mounting.
4 Detach the Table-Top Stand
from the TV.
KD-65X70G
1 Remove one side of the Table-Top Stand
at a time. Firmly hold the Table-Top Stand
securely with both hands while the other
people lift up the TV.
2 Repeat the previous step and remove the
other side of the Table-Top Stand.
Note
Three or more people are required to detach the
Table-Top Stand.
Be careful not to use excessive force while detaching
the Table-Top Stand from the TV as it may cause the
TV set to fall resulting in personal injury or physical
damage to the TV.
Take care when handling the Table-Top Stand to
prevent damage to the TV.
Be careful when lifting the TV as the Table-Top Stand
is detached, the Table-Top Stand may topple over
and cause personal injury.
Take care when removing the Table-Top Stand from
the TV to prevent it from falling over and damaging
the surface that the TV is sitting on.
Be sure to store the removed Table-top Stand and its
screws in a safe place, keeping them away from
children. You will need them if you want to use the TV
on a table in the future. The Table-Top Stand cannot
be purchased separately.
− 11 (GB) −
GB
KD-55X70G
Note
When installing the Wall-Mount Bracket, do not use
the screws removed from the Table-Top Stand.
Be sure to store the removed Table-top Stand and its
screws in a safe place, keeping them away from
children. You will need them if you want to use the TV
on a table in the future. The Table-Top Stand cannot
be purchased separately.
Installing the TV on the wall
1 Install the TV onto the Base or
Base Adaptor.
For the location of the Pulleys to the
hang on the Base or Base Adaptor, refer
to the table of step 3 in “Deciding on the
installation location” on page 7.
Gently slide down the TV and hang the
Pulleys attached to the rear of the TV
to the Base or Base Adaptor, making
sure to confirm the shape of the holes.
After installing the TV on the wall,
confirm the Pulleys are firmly latched
into the Base or Base Adaptor.
Release both hands slowly to ensure
that the TV does not fall.
Standard mounting (2-a)
− 12 (GB) −
GB
Slim mounting (2-b)
WARNING
Be sure that two or more persons (three or more
persons for 75 inches and above TV set) hold the TV
when carrying it.
2 Preventing the bottom of the TV
from shifting.
Take up the slack of Belt and attach it
to the wall tightly.
2-a 2-b
Use a 5 mm diameter screw or
equivalent (not supplied).
Note
Try to pull the bottom of the TV towards yourself
slightly, to make sure that it does not move forward.
If there is any movement, it is not fixed correctly, and
the Belt should be secured firmly again.
Confirming the completion of
the installation
Check the following points.
The Pulleys are firmly hung onto the Base
or Base Adaptor.
The cord and the cable are not twisted or
pinched.
The Belt is tight with no slack.
WARNING
Improper placement of the AC power cord (mains lead),
etc., may cause fire or electric shock through a short
circuit. Be sure to confirm the completion of the
installation for safety.
− 13 (GB) −
GB
Other information
When removing the TV, reverse the previous
installation procedure.
WARNING
Be sure that two or more persons (three or more persons
for 75 inches and above TV set) hold the TV when
removing it.
Specifications
f
c
d
b
a
g
e
h2h1
Dimensions: (Approx.) [mm]
a : 400
b : 300
c : 200
d : 100
e : 80
f : 480
g : 100
h1 : 20 (case 2-b)
h2 : 60 (case 2-a)
Weight (base only): (Approx.) [kg]
0.8
Design and specifications are subject to change without
notice.
− 2 (CS) −
使用 Sony 挂壁式支架 (SU-WL450) 的安装信息
支持型号:
KD-65X70*G / 55X70*G / 49X70*G / 43X70*G
*在实际机型名称中,“”指的是特定于每个型号的数字和/或字符。
致用户
为保护产品和安全理由,Sony 坚持建议安装您的电视的任务由 Sony 经销商或授权承包商进行。请勿尝
试自行安装。
致 Sony 经销商和承包商
安装、定期维修和检查此产品时,请务必注意安全。
安装本产品需要足够的专业技能, 尤其是确定用于承受电视机重量的墙壁的强度。务必将本产品的墙
上安装托付于 Sony 经销商或授权承包商并在安装时特别注意安全。对于处置不当或安装不妥造成的
损害或人身伤害,Sony 将不负责任。
为了确保安全和正确安装,请遵循挂壁式支架使用说明书、电视机设定指南以及本手册中的说明。
− 3 (CS) −
CS
安全事项
感谢您购买本产品。
致用户
安装本产品要求具有一定的技术。确保将
安装工作委托给 Sony 经销商或经许可的
承包商,并在安装过程中特别注意安
全。Sony 对操作不当或安装不正确,或安
装任何非指定产品而引起的任何损坏或伤
害概不负责。您的法定权利(如果有的
话)不受影响。
致 Sony 经销商
安装本产品要求具有一定的技术。为安全
地进行安装工作,请务必仔细通读本说明
书。Sony 对操作不当或安装不正确而引起
的任何损坏或伤害均不负责。请在完成安
装后将本说明书交给用户。
本说明书介绍了正确使用本产品的信息,以及
为防止事故发生需注意的重要事项。请务必仔
细通读本说明书并正确使用本产品。保存好本
说明书以备将来参考。
Sony 的产品设计非常注重安全。然而,如果不
正确使用这些产品,则可能因火灾、电击、产
品倾倒或产品跌落而导致人员严重受伤。请务
必遵守安全注意事项以防止此类事故发生。
注意
指定产品
本挂壁式支架设计用于指定产品的电视机。请
参阅电视机的参考指南,确定本挂壁式支架是
否可用于该电视机。
致用户
警告
如果不遵守下列注意事项,则因火灾、电击
或产品跌落而导致人员严重受伤或死亡。
请务必将安装工作委托给经
许可的承包商,并确保在安
装过程中无儿童接近。
如果挂壁式支架或电视机安装不正确,则可能
发生下列事故。请确保安装工作由经许可的承
包商进行。

电视机可能跌落并造成人员严重受伤,如擦
伤或骨折等。

如果安装挂壁式支架的墙体不平稳、不平整
或与地面不垂直,则装置可能会跌落,从而
造成人员受伤或财产损失。墙体能承受的重
量应该至少是电视机重量的四倍。
(请参阅您电视机的参考指南,了解其重
量。)

如果墙壁上安装的挂壁式支架不够牢固,则
装置可能会跌落并造成人员受伤或财产损
失。
请务必将电视机的搬移或拆
卸工作委托给经许可的承包
商进行。
如果由经许可的承包商之外的其他人员进行电
视机的搬运或拆卸工作,则电视机可能跌落并
造成人员受伤或财产损失。请确保由两个或两
个以上(75 英寸及以上机型需要三个或三个以
上)的人员搬运或拆卸本电视机。
电视机安装完之后,请勿拆
下螺丝等零件。
否则,电视机可能会跌落并造成人员受伤或财
产损失。
请勿改装挂壁式支架的零部
件。
否则,挂壁式支架可能会跌落并造成人员受伤
或财产损失。
请勿将指定产品之外的其他
设备安装到支架上。
本挂壁式支架系为指定产品专门设计。如果您
安装非指定设备,则支架可能跌落或破裂,并
造成人员受伤或财产损失。
除电视机之外,请勿在挂壁
式支架上再加挂其他重物。
请勿左右或上下摇晃电视
机。
否则,电视机可能会跌落并造成人员受伤或财
产损失。
请勿倚靠或吊挂在电视机
上。
请勿倚靠或吊挂在电视机上,因为电视机可能
跌落到您身上,并造成人员严重受伤。
注意
如果不遵守下列注意事项,则可能导致人
员受伤或财产损失。
在清洁或维护过程中,请勿
对产品施加过大的力量。
请勿在电视机的顶部施加过大的力量。否则,
电视机可能会跌落并造成人员受伤或财产损
失。
注意事项

如果长期使用安装于挂壁式支架的电视机,
则视墙面材料而定,电视机后面或上面的墙
面可能会褪色,或出现墙纸脱落。

如果在墙壁上安装挂壁式支架后再将其拆
下,则墙壁上会留下螺丝孔。

请勿在容易受到机械振动的地方使用挂壁式
支架。
安装挂壁式支架
致 Sony 经销商
警告
下列说明仅适用于 Sony 经销商。请务必
阅读上述安全注意事项,并在安装、维护
和检查本产品时特别注意安全。
请勿将挂壁式支架装在会使
电视机的边角或侧面突出于
墙面的墙壁位置。
请勿将挂壁式支架装在柱子等会使电视机的边
角或侧面突出于墙面的墙壁位置。如果有人或
物体正巧撞到电视机的边角或侧面,则会引起
人员受伤或财产损失。
请勿将电视机安装在空调的
上面或下方。
如果电视机长期接触空调的漏水,或长期暴露
于空调的气流中,则可能造成火灾、电击或电
视机故障。
请务必按照本说明书中的指
示牢固地将挂壁式支架安装
在墙上。
如果有螺丝松动或掉落,则挂壁式支架会跌落
并造成人员受伤或财产损失。请务必使用适合
墙壁材料的螺丝牢固安装本装置。固定时请使
用四个或更多个 8 mm 直径(或相当规格)的
螺丝。
请务必按照本说明书中给
出的指示正确使用提供的
螺丝和附件。如果使用其
他替代零件,则电视机可
能会跌落,并造成人身伤
害或电视机损坏。
− 4 (CS) −
请务必按照本说明书中介绍
的步骤正确安装支架。
如果有螺丝松动或掉落,则电视机可能会跌
落,并造成人身伤害或电视机损坏。
请务必拧紧指定位置的螺
丝。
如果操作不当,则电视机可能会跌落,并造成
人身伤害或电视机损坏。
请小心勿使电视机在安装过
程中受到振动。
如果电视机受到振动,它可能会跌落或裂开。
这可能会引起人员受伤。
请务必将电视机安装在垂直
且平坦的墙壁上。
否则,电视机可能跌落并造成人员受伤。
正确安装电视机后,请正确
固定电缆。
如果电缆缠住人或物体,则可能导致人员受伤
或电视机损坏。
请勿夹住交流电源线或连接
电缆。
如果交流电源线或连接电缆被夹在装置和墙壁
之间或被用力弯曲、缠绕,则内部导线可能会
裸露在外并造成短路或断路。这可能会引起火
灾或电击。
不提供用于将挂壁式支架固
定于墙壁的螺丝。
在安装挂壁式支架时,请使用适合墙壁材料和
结构的螺丝。
− 5 (CS) −
CS
在墙壁上安装电视机
视电视机而定,安装步骤有所不同。
使用挂壁式支架 SU-WL450 将电视机安装到墙
上。
注意
如果电视机安装了台式底座,则先拆下台式底座。请参阅设
定指南并按照相反的步骤拆下台式底座。
固定挂壁式支架的附件时或者从电视机上拆下台式底座时,
请将电视机屏幕朝下放置在覆盖有厚软布的稳定水平表面
上,以免损坏液晶显示器表面。
务必将取下的螺丝放置在安全的地方,让螺丝远离儿童。
准备安装
开始安装前,请将本电视机的参考指南和设定
指南放于手边,方便查阅。
装配前,务必准备一把与螺丝相匹配的十字螺
丝刀。
确认电视机的安装位置。
准备四个或更多个 8 mm 直径和一个 5 mm 直
径或相当规格的螺丝(不提供)。选择适合墙
壁材料的螺丝。
检查零件
SU-WL450 随附部件
确认已包含所有零件。
底座 (20) (1) 滑轮 (2)
螺丝 PSW 6x20
(4)
带套管的螺丝
PSW 4x20 (2)
垫片 (20) (2) 皮带 (1)
M4套管 (20) (2) 螺丝 PSW 4x20
(2)
底座转接器 (2) 螺丝 PSW 4x10
(8)
垫片 (60) (2) 螺丝 PSW 6x50
(2)
M4套管 (2) 螺丝 PSW 4x50
(2)
− 6 (CS) −
确定安装位置
1 确定安装位置。
确保墙壁具有安装电视机的足够空间并且必须能支撑至少电视机四倍的重量。
请参阅以下图表将电视机安装到墙上。有关电视机的重量,请参阅电视机参考指南。
标准安装 窄安装
屏幕中心点
80
单位: mm
机型名称
显示器尺寸
屏幕中心
尺寸
用于安装的长度
标准安装 窄安装
KD-65X70G
1463 845 173 597 142 100
KD-55X70G
1241 721 95 460 141 100
KD-49X70G
1101 645 -15
*
314 119 78
KD-43X70G
970 570 23 315 119 77
* 支架定位于屏幕中心点下方。
注意
视安装而定,图表中的数字可能会有轻微变化。
当电视机安装在墙上时,电视机上端会向前轻微倾斜。
− 7 (CS) −
CS
按下图所示,在电视机、天花板和墙壁突出
部分之间留出适当的空间。
单位: mm
300
100
100
100
为了确保正确通风及防止脏物或灰尘堆积:
ˋ 请勿将电视机平放、上面朝下安装、向后安装或侧面
安装。
ˋ 请勿将电视机放置于架子、地毯、床或壁橱中。
ˋ 请勿用布(如窗帘)或物件(如报纸等)覆盖电视
机。
ˋ 请勿如下图所示安装电视机。
空气不流通。
墙壁
注意
如果您想将电缆布置到墙壁内,则在开始安装前在墙上
钻一孔穿⼊电缆线。
为防止夹到电缆,请在底座 (20) ,底座转接器
和垫片 (20) ,垫片 (60) 四周外的墙壁某处钻一
个孔。
2 选择挂壁式安装样式。有如下⼏
种可供选择。
2-a 标准安装
2-b 窄安装
请参阅步骤 1 中的表格。
警告
选择 2-b 时,背后端子的使用受到限制。
2-a 2-b
3 底座转接器安装位置请参阅下
表。若选择 2-b,请略过此步
骤。
机型名称 支架位置
KD-65X70G
b
KD-55X70G /
49X70G
c
KD-43X70G
d
a
d
b
c
− 8 (CS) −
选择 2-a 时,使用螺丝(PSW
4x10)将底座转接器 安装
到底座(20) 上。
4 决定各螺钉的位置以安装底座
(20) 。
参见第 13 页的规格。
选择 2-a 时,请使用底座转接器 的各孔
位置。
警告
安装电视机的墙壁能承受的重量应该至少是电视机重量的
四倍(请参阅您电视机的参考指南,了解其重量。)。
测定要安装电视机墙壁的强度。如果需要,请适当加固
墙壁。
在墙壁上安装底座
使用四个或更多个 8 mm 直径或相当规格的螺
丝(不提供)。

将四个螺钉固定在已经和底座(20) 相连
的底座转接器 各孔中(仅 2-a)。
在墙壁上水平安装底座 (20) 。
标准安装 (2-a)
窄安装 (2-b)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124

Sony KD-43X7000G Le manuel du propriétaire

Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues