Chief CMS495 Guide d'installation

Chief
Marque
Chief
Modèle
CMS495
Catégorie
Kits de montage
Taper
Guide d'installation
INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Angled Ceiling Adapter
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
CMS495
CMS495 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the CMS495 up to (and including)
the projector does not exceed 50 lbs (22.7 kg).
IMPORTANT ! : The CMS495 was designed specifically
to be used with the UL Listed CMS440 Lightweight
Suspended Ceiling Kit in order to make it compatible with
ceilings angled up to 45°. Do NOT attempt to use the
CMS495 with any other type of ceiling mount or with
ceilings angled more than 45°!
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
--SAVE THESE INSTRUCTIONS--
DIMENSIONS
EQUAL 1
(REAR ANGLE)
EQUAL 1
(FRONT ANGLE)
45° MAX INSTALLED ANGLE
EQUAL 2
(SIDE ANGLE)
EQUAL 2
(SIDE ANGLE)
EQUAL 3
(SIDE ANGLE)
EQUAL 3
(SIDE ANGLE)
AND EQUAL-3)
FRONT CABLE
CROSS CABLES
REAR CABLE
TO THE OPPOSING MOUNTING POINT ON THE CEILING
THE CROSS CABLES SHOULD INSTALL TO THE FRONT OR BACK OF THE PLATE AND MOVE
PLUMB
LINE
PLUMB
LINE
2.
NOTE:
ANGLES FROM PLUMB LINE (BETWEEN 10 AND 30 DEGREES) FOR THE FRONT AND BACK1.
OUTER CABLES (NOT THE CROSS CABLES) SHOULD BE AS CLOSE TO EQUAL IN EACH
PLANE AS POSSIBLE. THE FRONT AND REAR ANGLES FOR THE FRONT AND REAR CABLES
SHOULD BE CLOSE TO EQUAL (LEFT DRAWING EQUAL-1), AND THE SIDE ANGLE FOR THE
FRONT AND REAR CABLES SHOULD BE CLOSE TO EQUAL (CENTER DRAWING EQUAL-2,
538.4
21.20
PLUMB
LINE
PLUMB
LINE
203.2
8.00
Installation Instructions CMS495
3
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
CMS495 Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION
PARTS
5/32” (included with CMS440)
A (1)
[CMS495 adapter]
B (1)
[lower bolt plate]
C (4)
1/4-20”
D (4)
[Cable lock]
1/16” x 25’
[Cable]
E (4)
Installation Instructions CMS495
5
Installation and Assembly
IMPORTANT ! : The CMS495 was designed specifically
to be used with the UL Listed CMS440 Lightweight
Suspended Ceiling Kit in order to make it compatible with
ceilings angled up to 45°. Do NOT attempt to use the
CMS495 with any other type of ceiling mount!
Attach CMS495 to CMS440
1. Remove four 1/4-20” wing nuts from CMS440 to release
extension column support and lower bolt support plate from
CMS440 assembly. (See Figure 1)
NOTE: All parts of CMS440 will be used with CMS495 adapter.
Figure 1
2. Reuse four 1/4-20” wing nuts removed in Step 1 to secure
removed CMS440 extension column support and CMS440
lower bolt plate to CMS495 (A). (See Figure 3)
Figure 2
3. Use four 1/4-20” wing nuts (C) to attach CMS495 adapter
(A) and lower bolt plate (B) to CMS440 plate. (See Figure 3)
Figure 3
wing nuts x 4
extension column
lower bolt support plate
CMS440
main assembly
1
support
(A)
2
removed
extension column
CMS440 lower bolt support plate
wing nuts x 4
support
CMS440
(C) x 4
3
(A)
(B)
CMS495 Installation Instructions
6
Installation to Ceiling
1. Follow CMS440 installation instructions to complete
installation to ceiling, using four cables and cable locks
used with the CMS440 for the front and rear cables (See
Figure 4) and then the four cross cables (D) and four cable
locks (E). (See Figure 5)
NOTE: The cross cables should install to the front or back of
the plate and move to the opposing mounting point on
the ceiling. (See Figure 5) and (See Figure 6)
Figure 4
Figure 5
IMPORTANT ! : Angles from plumb line (between 10° and
30°) for the front and back outer cables (not the cross cables)
should be as close to equal in each plane as possible. The front
and rear angles for the front and rear cables should be close to
equal (upper drawing - Equal 1). The side angles for the front
and rear cables should be close to equal (lower drawing - Equal
2 and 3). (See Figure 6)
NOTE: Specific angles will vary depending on angle of the
ceiling.
Figure 6
CMS440 cables
(D) x 4
EQUAL 1
EQUAL 1
(FRONT ANGLE)
45° MAX INSTALLED ANGLE
EQUAL 2
(SIDE ANGLE)
EQUAL 2
(SIDE ANGLE)
EQUAL 3
(SIDE ANGLE)
EQUAL 3
(SIDE ANGLE)
FRONT CABLE
CROSS CABLES
REAR CABLE
PLUMB
LINE
PLUMB
LINE
PLUMB
LINE
PLUMB
LINE
Installation Instructions CMS495
7
2. Adjust angle of inner plate of CMS495 adapter until it is
positioned so that extension column will be installed straight
down through the ceiling. (See Figure 7)
Figure 7
3. Tighten angle adjustment screws to secure angle of inner
plate of CMS495 adapter. (See Figure 7)
Refer to CMS440 installation instructions to install tray to ceiling
tile and extension column to CMS440 extension column
support.
x 2
3
2
CMS495 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P 800.582.6480 / 952.225.6000
F 877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P +31 (0) 495 580 852
F +31 (0) 495 580 845
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
Chief Manufacturing, a products division
of Milestone AV Technologies
8800-002451 Rev00
2013 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
10/13
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Chief CMS495 Guide d'installation

Chief
Marque
Chief
Modèle
CMS495
Catégorie
Kits de montage
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents