Wacker Neuson RD7H-ES EU Manuel utilisateur

5000185489

21 0315

Operator’s Manual

Roller

RD 7

Notice d’Emploi

Rouleau

5000185489

Copyright

notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any

other type of reproduction is prohibited without express written permission from

Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker Neuson Production

Americas LLC represents an infringement of valid copyrights. Violators will be

prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

5000185465 19 0513

RD 7 Foreword

wc_tx003240gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

;

Machine

identification

A nameplate listing the model number, item number, revision number, and serial

number is attached to this machine. The location of the nameplate is shown above.

Serial number

(S/N)

For future reference, record the serial number in the space provided below. You will

need the serial number when requesting parts or service for this machine.

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 Refer to the separate Repair Manual for detailed instructions on servicing and

repairing the machine.

 If you are missing any of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Machine Item Number

RD 7H-ES 0009408, 0620794

RD 7H-S 0009487, 0620795

RD 7-RAW 0620079, 0620478, 0620596

wc_gr010180

Serial Number:

Foreword RD 7

4 wc_tx003240gb.fm

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

 The illustrations, parts, and procedures in this manual refer to Wacker Neuson

factory-installed components. Your machine may vary depending on the

requirements of your specific region.

CALIFORNIA

Proposition

65 Warning

Combustion exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to the State of California to cause cancer and

birth defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-

charge of sparks or flames from the engine exhaust. Spark arresters are qualified

and rated by the United States Forest Service for this purpose. In order to comply

with local laws regarding spark arresters, consult the engine distributor or the local

Health and Safety Administrator.

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and modifica-

tions. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neuson.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following conse-

quences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

2015-CE-RD7_en_FM10.fm

EC Declaration of Conformity

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin 53051 USA

Product

Product category

Product function

Item number

Net installed power

Measured sound power level

Guaranteed sound power level

RD 7H-ES, RD 7H-S

Vibrating Walk-Behind Rollers

To compact asphalt

0620794, 0620795

6.1 kW

106 dB(A)

108 dB(A)

Conformity Assessment Procedure

According to 2000/14/EC ANNEX VIII

Notified Body

Lloyds Register Verification Limited (Notified Body No 0038)

71 Fenchurch Street, London EC3M 4BS, United Kingdom

Directives and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following directives and standards:

2006/42/EC, 2000/14/EC, 2005/88/EC, 2004/108/EC, EN 500-1, EN 500-4

Authorized Person for Technical Documents

Leo Goeschka, Wacker Neuson Produktion GmbH & Co. KG, Preußenstraße 41,

80809 München

Menomonee Falls, WI, USA, 17.03.2015

Paul Sina

Manager, Product Engineering

For Wacker Neuson

Dan Domanski

Technical Director

For Wacker Neuson

Original Declaration of Conformity

Keith Herr

Managing Director

For Wacker Neuson

Table of Contents

RD 7

wc_bo5000185465_21TOC.fm

7

Foreword 3

EC Declaration of Conformity 5

1 Safety Information 9

1.1 Signal Words Used in this Manual ....................................................... 9

1.2 Machine Description and Intended Use ............................................. 10

1.3 Safety Guidelines for Operating the Machine ..................................... 11

1.4 Service Safety .................................................................................... 13

1.5 Operator Safety while Using Internal Combustion Engines ............... 15

1.6 Hydraulic Fluid Safety ........................................................................ 16

2 Labels 18

2.1 Label Locations .................................................................................. 18

2.2 Label Meanings .................................................................................. 19

3 Lifting and Transporting 25

4 Operation 27

4.1 Preparing the Machine for First Use ................................................... 27

4.2 Control / Component Locations .......................................................... 28

4.3 Components ....................................................................................... 29

4.4 Refueling the Machine ........................................................................ 30

4.5 Exciter ................................................................................................ 31

4.6 Back-Up Stop Pad .............................................................................. 31

4.7 Engine Crank ...................................................................................... 31

4.8 Parking Brake ..................................................................................... 32

4.9 Watering System ................................................................................ 32

4.10 Functions of the Engine Throttle Control ............................................ 33

4.11 Direction and Speed Control .............................................................. 34

4.12 Before Starting ................................................................................... 35

4.13 Position of the Operator ..................................................................... 35

4.14 Starting the Machine (RD 7H, RD 7H-S) ............................................ 36

4.15 Starting the Machine (RD 7H-ES) ...................................................... 38

4.16 Cold Weather Starting (RD 7H, RD 7H-S) ......................................... 39

4.17 Engine Speed ..................................................................................... 42

4.18 Stopping the Machine ......................................................................... 42

4.19 Emergency Shutdown Procedure ....................................................... 43

4.20 Machine Stability ................................................................................ 43

4.21 Operation on Slopes ........................................................................... 44

4.22 Rollovers ............................................................................................ 44

Table of Contents

RD 7

wc_bo5000185465_21TOC.fm

8

5 Maintenance 45

5.1 Periodic Maintenance Schedule ..........................................................45

5.2 Safety-Related Spare Parts .................................................................46

5.3 Checking Engine Oil Level ..................................................................48

5.4 Changing the Engine Oil .....................................................................49

5.5 Fuel System ........................................................................................51

5.6 Engine Air Filter ...................................................................................52

5.7 Checking and Adjusting the Valve Clearances ...................................53

5.8 Engine Cooling System .......................................................................54

5.9 Mechanical Oil Pressure Monitoring ....................................................55

5.10 Scraper Bars .......................................................................................56

5.11 Water Spray Bars ................................................................................57

5.12 Hydraulic Oil Requirements .................................................................58

5.13 Hydraulic Oil Level ..............................................................................59

5.14 Changing Hydraulic Fluid and Filter ....................................................60

5.15 Direction Lever Adjustment .................................................................61

5.16 Pressure Washing the Machine ..........................................................63

5.17 Storing the Machine ............................................................................63

5.18 Machine Disposal / Decommissioning .................................................64

6 Troubleshooting 65

7 Technical Data 66

7.1 Engine .................................................................................................66

7.2 Roller ...................................................................................................67

7.3 Lubrication ...........................................................................................67

7.4 Sound and Vibration Specifications .....................................................68

8 AEM Safety Manual 69

9 Schematics 96

9.1 Hydraulic Schematic ............................................................................96

9.2 Hydraulic Schematic Components ......................................................97

9.3 Hydraulic Diagram ...............................................................................98

9.4 Hydraulic Diagram Components .........................................................99

9.5 RD 7H-ES—Electrical Schematic ......................................................100

9.6 RD 7H-ES—Electrical Schematic Components ................................101

wc_si000744gb.fm

9

RD 7 Safety Information

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

wc_si000744gb.fm

10

Safety Information RD 7

1.2 Machine Description and Intended Use

This machine is a dual drum vibratory walk-behind roller. The Wacker Neuson

Walk-Behind Roller consists of an upper frame to which are mounted a diesel

engine, a hydraulic tank, a water tank, and a hydrostatic drive system; and a lower

frame which supports two steel drums, an exciter assembly, and a handle. The

engine powers the hydraulics that provide machine movement and drum vibration.

The vibrating drums smooth and compact the work surface as the machine moves.

The operator uses the handle to control machine speed and direction.

This machine is intended to be used for compacting sand, gravel, soil, and asphalt

on roadways, walkways, bridges, and parking lots.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine

damage caused by misuse is not covered under warranty.

The following are some examples of misuse:

 Using the machine as a ladder, support, or work surface

 Using the machine to carry or transport passengers or equipment

 Using the machine to tow other machines

 Using the machine to spray liquids other than water (i.e., diesel fuel on asphalt)

 Operating the machine outside of factory specifications

 Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual.

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

 Heat, noise, exhaust, and carbon monoxide from the engine

 Burns from hot hydraulic fluid

 Fire hazards from improper refueling techniques

 Fuel and its fumes

 Personal injury from improper lifting techniques or operating techniques

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

wc_si000744gb.fm

11

RD 7 Safety Information

1.3 Safety Guidelines for Operating the Machine

Operator

training

Before operating the machine:

 Read and understand the operating instructions contained in all manuals

delivered with the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Contact Wacker Neuson for additional training if necessary.

When operating this machine:

 Do not allow improperly trained people to operate the machine. People

operating the machine must be familiar with the potential risks and hazards

associated with it.

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

 have received instruction on how to properly use the machine

 are familiar with required safety devices

The machine must not be accessed or operated by:

 children

 people impaired by alcohol or drugs

Contact Wacker Neuson for additional training if necessary.

Application

area

Be aware of the application area.

 Keep unauthorized personnel, children, and pets away from the machine.

 Remain aware of changing positions and the movement of other equipment and

personnel in the application area/job site.

Be aware of the application area.

 Do not operate the machine in areas that contain flammable objects, fuels, or

products that produce flammable vapors.

Safety

devices,

controls, and

attachments

Only operate the machine when:

 All safety devices and guards are in place and in working order.

 All controls operate correctly.

 The machine is set up correctly according to the instructions in the Operator’s

Manual.

 The machine is clean.

 The machine’s labels are legible.

To ensure safe operation of the machine:

 Do not operate the machine if any safety devices or guards are missing or

inoperative.

 Do not modify or defeat the safety devices.

 Only use accessories or attachments that are approved by Wacker Neuson.

wc_si000744gb.fm

12

Safety Information RD 7

Safe

operating

practices

When operating this machine:

 Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

 Operate the machine with both of your feet on the ground! Do not stand, sit, or

ride on machine while in operation.

 Remain aware of changing surface conditions and use extra care when

operating over uneven ground, on hills, or over soft or coarse material. The

machine could shift or slide unexpectedly.

 Use caution when operating near the edges of pits, trenches or platforms.

Check to be sure that the ground surface is stable enough to support the weight

of the machine with the operator and that there is no danger of the roller sliding,

falling, or tipping.

 Position yourself safely when operating machine in reverse or on hills. Leave

enough space between yourself and the machine so you will not be placed in a

hazardous position should the machine slide or tip.

When operating this machine:

 Do not operate a machine in need of repair.

 Do not subject the roller to jarring impacts by driving it off curbs or off the back of

a truck or trailer.

 Do not transport the machine while it is running.

 Do not operate a machine in need of service or repair.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

wc_si000744gb.fm

13

RD 7 Safety Information

1.4 Service Safety

Service

training

Before servicing or maintaining the machine:

 Read and understand the instructions contained in all manuals delivered with

the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Only trained personnel shall troubleshoot or repair problems occurring with the

machine.

 Contact Wacker Neuson for additional training if necessary.

When servicing or maintaining this machine:

 Do not allow improperly trained people to service or maintain the machine.

Personnel servicing or maintaining the machine must be familiar with the

associated potential risks and hazards.

Precautions

Follow the precautions below when servicing or maintaining the machine.

 Read and understand the service procedures before performing any service to

the machine.

 All adjustments and repairs must be completed before operation. Do not

operate the machine with a known problem or deficiency.

 All repairs and adjustments shall be completed by a qualified technician.

 Turn off the machine before performing maintenance or making repairs.

Machine

modifications

When servicing or maintaining the machine:

 Use only accessories/attachments that are approved by Wacker Neuson.

When servicing or maintaining the machine:

 Do not defeat safety devices.

 Do not modify the machine without the express written approval of Wacker

Neuson.

Replacing

parts and

labels

 Replace worn or damaged components.

 Replace all missing and hard-to-read labels.

 When replacing electrical components, use components that are identical in

rating and performance to the original components.

 When replacement parts are required for this machine, use only Wacker

Neuson replacement parts or those parts equivalent to the original in all types of

specifications, such as physical dimensions, type, strength, and material.

Cleaning

When cleaning and servicing the machine:

 Keep the machine clean and free of debris such as leaves, paper, cartons, etc.

 Keep the labels legible.

When cleaning the machine:

 Do not clean the machine while it is running.

 Never use gasoline or other types of fuels or flammable solvents to clean the

machine. Fumes from fuels and solvents can become explosive.

wc_si000744gb.fm

14

Safety Information RD 7

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or

maintaining this machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

In addition, before servicing or maintaining the machine:

 Tie back long hair.

 Remove all jewelry (including rings).

Safe service

practices

 Check all external fasteners at regular intervals.

 Some service procedures require that the machine’s battery be disconnected.

To reduce the risk of personal injury, read and understand the service

procedures before performing any service to the machine.

 Turn engine off before servicing machine. If the engine has electric start,

disconnect negative terminal on battery.

 Before you start the machine, ensure that all tools have been removed from the

machine and that replacement parts and adjusters are firmly tightened.

After Use

 Stop the engine when the machine is not being operated.

 Close the fuel valve, if equipped, when machine is not being operated.

 Ensure that the machine will not tip over, roll, slide, or fall when not being

operated.

 Store the machine in a clean, dry location out of the reach of children.

wc_si000744gb.fm

15

RD 7 Safety Information

1.5 Operator Safety while Using Internal Combustion Engines

Operating

safety

When running the engine:

 Keep the area around exhaust pipe free of flammable materials.

 Check the fuel lines and the fuel tank for leaks and cracks before starting the

engine. Do not run the machine if fuel leaks are present or the fuel lines are

loose.

When running the engine:

 Do not smoke while operating the machine.

 Do not run the engine near sparks or open flames.

 Do not touch the engine or muffler while the engine is running or immediately

after it has been turned off.

 Do not operate a machine when its fuel cap is loose or missing.

 Do not start the engine if fuel has spilled or a fuel odor is present. Move the

machine away from the spill and wipe the machine dry before starting.

Refueling

safety

When refueling the engine:

 Clean up any spilled fuel immediately.

 Refill the fuel tank in a well-ventilated area.

 Replace the fuel tank cap after refueling.

 Use suitable tools for refueling (for example, a fuel hose or funnel).

When refueling the engine:

 Do not smoke.

 Do not refuel a hot or running engine.

 Do not refuel the engine near sparks or open flames.

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety standards could result in severe injury or

death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison.

Exposure to carbon monoxide can kill you in minutes.

f NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through such items as exhaust fans or hoses.

wc_si000744gb.fm

16

Safety Information RD 7

1.6 Hydraulic Fluid Safety

Safety

instructions

 Inspect the hydraulic system thoroughly before operating the machine.

 Do not touch hydraulic fluid or hydraulic components while the machine is

operating. Wait until the machine is cool.

 Before disconnecting hydraulic fittings or hoses, ensure that all pressure has

been bled from the circuit. Set all controls in neutral, turn engine off, and allow

the fluids to cool before loosening hydraulic fittings or attaching test gauges.

 Hydraulic fluid escaping under high pressure may penetrate the skin, cause

burns, blind, or cause other serious injuries or infections. Contact a physician

immediately for treatment if your skin has been penetrated by hydraulic fluid,

even if the wound seems minor.

 Fluid leaks from small holes are often practically invisible. Do not use your bare

hands to check for leaks. Check for leaks using a piece of cardboard or wood.

 Hydraulic fluid is extremely flammable. Stop the engine immediately if a

hydraulic leak is detected.

 After servicing the hydraulics, make sure all components are reconnected to the

proper fittings. Failure to do so may result in damage to the machine and/or

injury to a person on or near the machine.

WARNING

Possibility of severe injury. Hydraulic fluid is under high pressure and becomes very

hot during operation.

f To avoid injury, obey the safety instructions listed below.

wc_si000744gb.fm

17

RD 7 Safety Information

Notes

wc_si000745gb.fm

18

Labels RD 7

2 Labels

2.1 Label Locations

wc_gr010241

O

K

P

E

A

R

F

M

L

G

B

C

D

H

J

N

Q

S

V

T

U

W

X

P

R

wc_si000745gb.fm

19

RD 7 Labels

2.2 Label Meanings

A NOTICE

No lift point

B Vibration control ON/OFF

C Read and understand the supplied Operator’s

Manual before operating the machine. Failure

to do so increases the risk of injury to yourself

and others.

D

AND

wc_si000745gb.fm

20

Labels RD 7

— Check engine oil level.

Use SAE10W30.

Check the fuel level.

— Engage parking brake.

— Turn vibration off.

— Place throttle in the FAST position.

— Pull decompression lever up.

— Insert crank handle.

— Rotate crank handle counterclockwise 5X.

— Remove crank handle.

La page charge ...

Wacker Neuson RD7H-ES EU Manuel utilisateur

Ce manuel convient également à

Wacker Neuson RD7H-ES EU Manuel utilisateur

dans d''autres langues

Documents connexes