Simplicity 305447-0115-E1 Manuel utilisateur

Catégorie
Accessoires pour véhicules automobiles
Taper
Manuel utilisateur
Briggs & Stratton Corporation
Milwaukee, Wisconsin 53201
www.briggsandstratton.com
Copyright 2003 by Briggs & Stratton Corporation
FORM NO. MS-5375-5/03
PRINTED IN U.S.A.
290000, 300000, 350000, 380000
Operating & Maintenance Instructions
Betriebsanleitung & Wartungsvorschriften
Drifts- og vedligeholdelsesvejledning
Instrucciones de Mantenimiento & Operación
Instructions d’utilisation et de maintenance
Ïäçãßåò Ëåéôïõñãßáò & Óõíôñçóçò
Istruzioni per l’uso e la manutenzione
Anvisninger for bruk og vedlikehold
Gebruiksaanwijzing
Instruções de operação e de manutenção
Instruktionsbok
Käyttö & Huolto-ohjeet
GB
D
E
DK
F
I
NL
P
SF
S
N
GR
£
¢
¡
©
°C
-30
°F
-20 0
20 40 60 80 100
-20 -10 0 10 20 30 40
*
**
32
12
11
10
9
8
3
4
5
6
1
2
7
4
13
14
16
15
17
¤¥
GB
GB
1
Note: (This note applies only to engines used in the U.S.A.) Maintenance, replacement or repair of the emission control devices and systems may be performed
by any nonroad engine repair establishment or individual. However, to obtain no charge repairs under the terms and provisions of the Briggs & Stratton
warranty statement, any service or emission control part repair or replacement must be performed by a factory authorized dealer.
How To Use Manual Figures
¡ -- ¨ refer to figures inside covers.
-- refer to engine components in figure
¡.
-- refer to part/action in figures.
19
1
Record your engine
Model, Type and Code numbers
here for future use.
Record your date of purchase here for future use.
In the state of California, OHV Model Series 290000, 300000,
350000 and 380000 engines are certified by the California Air
Resources Board to meet emissions standards for 250 hours.
Such certification does not grant the purchaser, owner or
operator of this engine any additional warranties with respect
to the performance or operational life of this engine. This
engine is warranted solely according to the product and
emissions warranties stated elsewhere in this manual.
Technical Information
POWER RATINGS: The power ratings for an individual
engine model are initially developed by starting with
SAE (Society of Automotive Engineers) code J1940
(Small Engine Power & Torque Rating Procedure) (Re-
vision 2002-05). Given both the wide array of products
on which our engines are placed, and the variety of en-
vironmental issues applicable to operating the equip-
ment, it may be that the engine you have purchased will
not develop the rated horsepower when used in a piece
of power equipment (actual “on-site” power). This dif-
ference is due to a variety of factors including, but not
limited to, the following: differences in altitude, temper-
ature, barometric pressure, humidity, fuel, engine lu-
brication, maximum governed engine speed, individual
engine to engine variability, design of the particular
piece of power equipment, the manner in which the en-
gine is operated, engine run-in to reduce friction and
clean out of combustion chambers, adjustments to the
valves and carburetor , and other factors. The power
ratings may also be adjusted based on comparisons to
other similar engines utilized in similar applications,
and will therefore not necessarily match the values de-
rived using the foregoing codes.
Engine Components (see fig. ¡)
1
Oil fill cap
2
Dipstick
3
Fuel pump (if equipped)
4
Spark plug
5
Engine Model Type Code
xxxxxx xxxx xx xxxxxxxx
6
12V electric starter (if equipped)
7
Oil drain plug
8
Blower housing
9
Rope handle
10
Carburetor or LPG/NG Fuel mixer
11
Stop switch (if equipped)
12
Air cleaner (without fuel tank)
13
Fuel shut-off valve (if equipped)
14
Air cleaner (with fuel tank)
15
Fuel fill/fuel tank (if equipped)
16
Exhaust manifold
17
Oil filter (if equipped)
Hazard Symbols and Meanings
Explosion
Toxic Fumes
Moving Parts
Shock
Hot Surface
Kickback
Fire
International Symbols and Meanings
On Off
Fuel Shutoff
Read Owner’s
Manual
Stop
Fuel
ChokeSafety Alert
Oil
Safety Precautions
* Briggs & Stratton does not necessarily know what
equipment this engine will power. For that reason,
you should carefully read and understand the
operating instructions for the equipment on which
your engine is placed.
BEFORE OPERATING ENGINE
Read entire Operating & Maintenance Instructions
AND the instructions for the equipment this engine
powers.*
Failure to follow instructions could result in serious
injury or death.
THE OPERATING & MAINTENANCE
INSTRUCTIONS CONTAIN SAFETY
INFORMATION TO
Make youaware of hazards associated with engines
Inform you of the risk of injury associated with those
hazards, and
Tell you how to avoid or reduce the risk of injury.
The safety alert symbol is used to identify safety
information about hazards that can result in personal injury.
A signal word (DANGER, WARNING, or CAUTION) is used
with the alert symbol to indicate the likelihood and the potential
severity of injury. In addition, a hazard symbol may be used to
represent the type of hazard.
DANGER indicates a hazard which, if not avoided,
will result in death or serious injury.
WARNING indicates a hazard which, if not avoided,
could result in death or serious injury.
CAUTION indicates a hazard which, if not avoided,
might result in minor or moderate injury.
CAUTION
, when used without the alert symbol,
indicates a situation that could result in damage to
the engine.
The engine exhaust from this product contains
chemicals known to the State of California to cause
cancer , birth defects, or other reproductive harm.
WARNING
GB
2
WARNING
Gasoline and its vapors are extremely flammable
and explosive.
Fire or explosion can cause severe burns or death.
WHEN FUELING
Turn engine OFF and let engine cool at least 2
minutes before refueling engine.
Fill fuel tank outdoors or in well-ventilated area.
On GASOLINE operated engines, do not overfill
fuel tank. Fill tank to approximately 1-1/2 inches
below top of neck to allow for fuel expansion.
Keep fuel away from sparks, open flames, pilot
lights, heat, and other ignition sources.
Check fuel lines, tank, cap, and fittings frequently
for cracks or leaks. Replace if necessary.
WHEN STARTING ENGINE
Make sure spark plug, muffler, fuel cap and air
cleaner are in place.
Do not crank engine with spark plug removed.
If fuel spills, wait until it evaporates before starting
engine.
If GASOLINE engine floods, set choke to
OPEN/RUN position, place throttle in FAST and
crank until engine starts.
WHEN OPERATING EQUIPMENT WITH
GASOLINE ENGINE
Do not tip engine or equipment at angle which
causes gasoline to spill.
Do not choke carburetor to stop engine.
WHEN TRANSPORTING EQUIPMENT
On gasoline engine, transport with fuel tank
EMPTY or with fuel shut-off valve OFF.
On NATURAL/ LIQUID PETROLEUM (LP) GAS
engine, transport with fuel cylinder empty, and
valve closed, or tank disconnected.
WHEN STORING FUEL OR EQUIPMENT WITH
FUEL IN TANK OR IN FUEL CYLINDER
Store away from furnaces, stoves, water heaters
or other appliances that have pilot light or other
ignition source because they can ignite gasoline
vapors.
Engines give off carbon monoxide, an odorless,
colorless, poison gas.
Breathing carbon monoxide can cause nausea,
fainting or death.
Start and run engine outdoors.
Do not start or run engine in enclosed area, even if
doors or windows are open.
WARNING
Gaseous fuels are extremely flammable and readily
form explosive air-vapor mixtures at ambient tem-
peratures.
IF YOU SMELL GAS:
DO NOT start the engine.
DO NOT actuate any electrical switches.
DO NOT use the phone in the vicinity.
Evacuate the area.
Contact the gas supplier or fire department.
REMEMBER:
LPG vapor is heavier than air and trends to collect in
low areas. NG vapor is lighter than air and tends to
collect in high areas. Both may travel to remote
locations.
Keep all flames, sparks, pilot lights, and other
ignition sources away from the area where the
engine is operated or repaired.
DO NOT smoke when operating or repairing the
engine.
DO NOT store gasoline or other flammable vapors
or liquids in the vicinity of the engine.
BEFORE doing any service work to the engine, shut
off the gas supply.
After initial installation or servicing, check for gas
leaks. DO NOT use an open flame. Apply very
soapy water or leak test solution with a brush and
look for bubbles.
Keep the equipment and the area surrounding the
engine free of debris.
Install the fuel system according to applicable
fuel/gas codes.
Wear eye protection when doing repair work.
Frostbite can result from skin/eye contact with
leaking LP liquid.
Installation, adjustment and repair work should be
done by a qualified technician.
Flexible supply lines should be checked regularly to
make sure they are in good condition. Replace
damaged or leaking c omponents.
WARNING
WARNING
Unintentional sparking can result in fire or
electric shock.
Unintentional start-up can result in entangle-
ment, traumatic amputation, or laceration.
BEFORE PERFORMING ADJUSTMENTS OR RE-
PAIRS
Disconnect spark plug wire and keep it away from
spark plug.
Disconnect battery at negative terminal (only
engines with electric start).
WHEN TESTING FOR SPARK
Use approved spark plug tester.
Do not check for spark with s park plug removed.
WARNING
Starting engine creates sparking.
Sparking can ignite nearby flammable gases.
Explosion and fire could result.
If there is natural or LP gas leakage in area, do not
start engine.
Do not use pressurized starting fluids because
vapors are flammable.
WARNING
Allowmuffler, engine cylinder and fins to cool before
touching.
Remove accumulated combustibles from muffler
area and cylinder area.
Install and maintain in working order a spark
arrester before using equipment on forest-covered,
grass-covered, brush-covered unimproved land.
The state of Californiarequiresthis (Section 4442 of
the California Public Resources Code). Other
states may have similarlaws. Federallaws apply on
federal land.
WARNING
Running engines produce heat. Engine parts,
especially muffler, become extremely hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass,
brush, etc. can catch fire.
GB
3
Rotating parts can contact or entangle hands, feet,
hair, clothing, or accessories.
Traumatic amputation or severe laceration can
result.
Operate equipment with guards in place.
Keep hands and feet away from rotating parts.
Tie up long hair and remove jewelry.
Do not wear loose-fitting clothing, dangling
drawstrings or items that could become caught.
WARNING
Rapid retraction of starter cord (kickback) will pull hand
and arm toward engine faster than you can let go.
Broken bones, fractures, bruises or sprains could
result.
When starting engine, pull cord slowly until
resistance is felt, then pull rapidly.
Remove all external equipment/engine loads
before starting engine.
Directcoupled equipment components such as, but
not limited to, blades, impellors, pulleys, sprockets,
etc., must be securely attached.
WARNING
Oil Recommendations (see fig. ©)
Engine shipped from Briggs & Stratton without oil. Before
starting engine
, fill with oil. Do not over-fill.
Use a high quality detergent oil classified “For Service SF, SG,
SH, SJ” or higher such as Briggs & Stratton 30W, Part Number
100005 (20 oz.) or 100028 (48 oz.). Use no special additives
with recommended oils. Do not mix oil with gasoline.
Choose the SAE viscosity grade of oil from this chart that
matches the starting temperature anticipated before the next
oil change. (see fig.
©)
Note: Synthetic oil meeting ILSAC GF-2,
API certification mark and API service symbol
(shown at left) with “SJ/CF ENERGY CON-
SERVING” or higher, is an acceptable oil at all
temperatures. Use of synthetic oil does not
alter required oil change intervals.
* Air cooled engines run hotter than automotive engines.
The use of non-synthetic multi-viscosity oils (5W-30,
10W-30, etc.) in temperatures above 40° F(4° C) will
result in higher than normal oil consumption. When using
a mult i- viscosi ty oil, check oil level more frequent ly.
** SAE 30 oil, if used below 40° F(4° C), will result in hard
starting and possible engine bore damage due to
inadequate lubrication.
Check oil level (see fig. ©)
Oil capacity: approximately 1-1/2 quarts (48 ounces or 1.6
liters) when changing oil and filter
. (Oil capacity will be greater
if engine is equipped with remote
oil filter.)
Oil filling procedure: first add 1 quart (32 ounces or 1 liter).
Startand run engine at idle for 30 seconds. Shut engine offand
wait 30 seconds. Then add more oil slowly to bring level to Full
mark on dipstick. Check for oil leaks. Tighten dipstick firmly
before starting engine.
Oil checking procedure: before starting engine, place
engine level and clean around oil fill
. Remove dipstick ,
wipe with clean cloth, insert and tighten down again. Remove
dipstick and check oil level. Oil should be at FULL mark
.If
oil is required, add slowly. Tighten dipstick firmly before
starting engine.
Fuel Recommendations
Gasoline Powered Engines
Use clean, fresh, lead-free gasoline with a minimum of 85
octane. Leaded gasoline may be used if it is commercially
available and if unleaded is unavailable. Purchase fuel in
quantity that can be used within 30 days.
Do not use gasoline which contains Methanol. Do not mix oil
with gasoline. In U.S.A. leaded gasoline may not be used.
This engine is certified to operate on gasoline. Exhaust
Emission Control System: EM (Engine Modifications).
For engine protection, we recommend using Briggs & Stratton
Fuel Stabilizer available from an Authorized Briggs & Stratton
Service Dealer.
Natural (NG) / Liquid Propane (LPG)
Gas Powered Engines
Use clean, dry fuel, free of moisture or any particulatematerial.
Using fuels outside the following recommended values may
cause performance problems.
In engines set upto run on LPG, commercial grade HD5 LPGis
recommended. Recommended fuel composition is fuel with a
minimum fuel energy of 2500 BTU’s/ft
3
with maximum
propylene content of 5% and butane and heavier gas content
of 2.5% and minimum propane content of 90%.
NG or LPG engines are certified to operate on natural or liquid
propane gas.
The equipment on which thisengine is
mountedis equippedwith an automat-
ic safety gas “fuel lock-off” valve. DO
NOT operate the equipment if the “fuel lock-off” valve is
missing or inoperative.
Adding Fuel - Gasoline
Before refueling, allow
engine to cool 2 minutes.
Clean around fuel fill before removing cap to refuel. Remove
cap. Fill tank to approximately 1-1/2 inches below top of neck
to allow for fuel expansion. Be careful not to overfill.
Adding Fuel - Natural (NG) / Liquid Propane (LPG)
Read the operating instructions supplied by the equipment
manufacturer for information on refueling natural or LP gas
engine.
Starting (see figs. ¢£)
ALWAYS KEEP HANDS AND FEET CLEAROF
EQUIPMENT MOVING PARTS.
Do not use a pressurized starting fluid.
Vapors are flammable.
Start, store and fuel equipment in level position.
Check oil level.
Open fuel shut-off valve, if equipped.
BEFORE STARTING - LPG / NG Engines
(see fig.
¢)
The LPG / NG mixer is equipped with solenoid , fuel inlet ,
12 volt connector , and equipped for a fuel lock-off valve .
CAUTION:
All LPG / NG fuel mixers are equipped with a solenoid.
When operating on LPG fuel,12 volts MUST be supplied to
connector .
When operating on NG fuel, 12 volts MUST NOT be
supplied to connector .
1. Move throttle control to FAST position.
2. Push rocker switch to I position.
BEFORE STARTING - Gasoline Engines
(see fig.
£)
If engine runs low on oil, an oil pressure switch (if engine is
equipped) will either activate a warning device or stop the
engine. (Read the operating instructions supplied by the
equipment manufacturer to determine which way your engine
is equipped.) See Oil pressure on next page.
1. Open fuel shut-off valve
, if equipped.
2. Move choke control
to CHOKE position.
Note: If engine does not start, remove air cleaner to check
choke. Choke must fully close. If not, see Adjustments.
3. Move throttle control
to FAST position.
4. Push rocker switch
to I position.
Rewind starter, if equipped (see fig. ¤)
Grasp rope handle and pull slowly until
resistance is felt. Then pull cord rapidly to
overcome compression, prevent kickback
and start engine. Repeat if necessary with choke in RUN
positionthrottlein FAST. When engine starts,operatein FAST.
Electric starter (see fig. ¤)
On engines equipped with 12 volt starting systems, turn key to
START position
or press button . Repeat if necessary
with choke off and throttle control in FAST position. Operate
engine with choke off and throttle in FAST position.
Note: If equipment manufacturer has supplied battery,
charge it before trying to start engine, as equipment manufac-
turer recommends. Use short starting cycles (15 secs. per
min.) to prolong starter life. Extended cranking can damage
starter motor.
CAUTION:Ifengine is equipped with batteryfor electricstarter,
do not operate engine with battery disconnected.
Stopping (see fig. ¥)
Do not move choke control to CHOKE to stop engine. Backfire
or engine damage may occur. Move throttle control
to IDLE
or SLOW position, then to STOP or turn key to OFF
or push
rocker switch
to 0 posit ion.
Always remove key from switch when equipment is not in use
or left unattended.
When engine or equipment is trans-
ported, close fuel shut-off valve, if
equipped, to prevent fuel leakage.
GB
4
Maintenance Schedule
Follow the hourly or calendar intervals, whichever occur
first. More frequent service is required when operating in
adverse conditions noted below.
First 8 Hours
D Change oil
Every 8 hours or daily
D Check oil level
D Clean around muffler, linkage and springs
Every 25 hours or every season
D Change oil if operating under heavy load or high
ambient temperature
D Service air cleaner pre-cleaner*
Every 50 hours or every season
D Change oil
D Clean and inspect spark arrester, if equipped
Every 100 hours or every season
D Service air cleaner cartridge*
D Replace oil filter, if equipped
D Clean oil cooler, if equipped*
D Clean cooling system*
D Check valve clearance -- NG / LPG engines
Every season
D Replace spark plugs
D Replace in-l ine fuel fi lt er
D Check valve clearance
* Clean more often under dusty conditions, or when
airborne debris is present or after prolonged opera-
tion cutting tall, dry grass.
Maintenance (see figs. §¨)
See any Authorized Briggs & Stratton Dealer for correct
replacement parts.
To prevent acciden-
tal starting, remove
spark plug wire
and ground it before
servicing, and dis-
connect battery at negative terminal, if equipped.
Oil service (see fig. §)
Check oil level regularly.
Be sure correct oil level is maintained. Check every 8 hours or
daily, before s tarting engine. See oil filling procedure, Oil
Recommendations.
Change oil.
Change oil after first 8 hours of operation. Change oil while
engine is warm. Refill with new oil of recommended SAE
viscosity grade. (see fig.
©)
Change oil filter
, if equipped. (see fig. §)
Replace oil filter after every 100 hours of operation or every
season, whichever occurs first. Before installing new filter,
lightly oil filter gasket with fresh, clean engine oil. Screw filter
on by hand until gasket contacts oil filter adapter.Tighten 1/2 to
3/4 turn more. Start and run engine at IDLE to check for oil
leaks. Stop engine. Recheck oil level and add oil if required.
Oil pressure
If oil pressure drops below 1-4 psi (.1-.2 kg/cm
2
), an oil
pressure switch (if engine is equipped) will either activate a
warningdevice or s top the engine. Check oil levelwith dipstick.
If oil level is between ADD and FULL mark on dipstick, do
not
try to restart engine
. Contact an Authorized Briggs & Stratton
Service Dealer. Do not operate engine until oil pressure
is
corrected
.
If oil level is below ADD mark on dipstick, add oil to bring level to
FULL mark. Restart engine and check oil pressure. If pressure is
normal, continue to operate engine .
Note: Oil pressure gauge, if engine is equipped, is supplied
by manufacturer of equipment.
Maintenance Cont’d
Air cleaner, dual element (see fig. ¨)
1. Remove cover.
2. Carefully slide pre-cleaner
off cartridge .
3. Remove knob and plate. Carefully remove cartridge to
prevent debris from entering carburetor
.
Replace pre-cleaner, if equipped, or cartridge if very dirty or
damaged.
To service cartridge, clean by tapping gently on a flat surface.
Do not use petroleum solvents, e.g., kerosene, which will
cause cartridge to deteriorate. Do not use pressurized air,
which can damage cartridge. Do not oil cartridge.
4. Reinstall cartridge, plate and knob.
Note: Top side of air cleaner plate
is marked “UP” (only on
engines equipped with integral fuel tank).
5. Install pre-cleaner on cartridge and replace cover.
Spark plug service (see fig. )
DO NOT check
f
or spark with
spark plugs removed. Useonly
Briggs & Stratton Spark Teste
r
, to check for spark.
DO NOT crank engine with spark plug removed. If engine is
flooded, place throttle in FAST and crank until engine starts.
Spark plug gap
should be .76 mm or 0.030 in.
Replace spark plugs every season. Spark tester and spark
plug wrench are available from any Authorized Briggs &
Stratton Service Dealer.
Note: In some areas, local law requires using a resistor spark
plug to suppress ignition signals. If this engine was originally
equipped with resistor spark plug, use same type of spark plug
for replacement.
Keep engine clean (see fig. )
Periodically remove chaff/debris buildup from engine. Do not
spray engine with water because water could contaminate
fuel. Use a brush or compressed air.
A
ccumulation o
f
cha
f
f
/
debris around ex-
haust manifol d/muffler
could cause a
fire. Inspect and clean before every use.
Keep linkage, springs and controls
free of debris.
If muffler is equipped with spark arrester screen
, remove
spark arrester screen for cleaning and inspection every 50
hours or every season. Replace if damaged.
Replace in-line fuel filter every season.
Drain fuel tank or close fuel shut-off valve
before replacing filter.
Clean oil cooler
every 100 hours or every season, if
equipped.
Chaff or debris may clog engine’s air cooling system,
especially after prolonged service. Every 100 hours or every
season, clean internal cooling fins and surfaces to prevent
overheating and engine damage. Remove blower housing to
clean areas shown
.
Check Valve Clearance
Gasoline Engines -
Check valve clearance yearly (intake and exhaust .10-.15 mm).
NG / LPG Engines -
Valve clearance must be checked after every 100 hours of
operation. Adjust if necessary.
Adjustments (see fig. ¦)
To prevent acciden-
tal starting, remove
spark plug wire
and ground it before
adjusting, and dis-
connect battery at negative terminal, if equipped.
Carburetor adjustments
The manufacturer of the equipment on which this
engine is installed specifies top speed at which the
engine will be operated. DO NOT EXCEED this
speed.
See an Authorized Briggs & Stratton Dealer for carburetor
adjustment.
Start engine and warm up approximately 5 minutes before
adjusting. With engine running, place throttle control in SLOW
position.Rotate carburetor throttle lever against the idle speed
screw and hold it. Turn idle speed screw to obtain 1400 rpm
(1200 rpm on twin barrel carburetor). While still holding
carburetor throttle lever against idle speed screw, turn idle
mixture valve with limiter cap screw midway between limits.
DO NOT remove limiter cap. DO NOT force beyond limit. On
twobarrelcarburetor,set cylinder#1 idlemixture valve midway
between limits. Then set cylinder #2 idle mixture valve midway
between limits while holding carburetor throttle lever against
idle speed screw.
IDLE MIXTURE VALVES
WITH LIMITER CAPS
CYL # 1CYL # 2
Two barrel carburetorSingle barrel carburetor
CARBURETOR
THROTTLE LEVER
IDLE SPEED SCREW
Readjust the idle speed to 1200 rpm, if governed idle spring is
red, or 900 rpm, if governed idle spring is white as illustrated
below. Release carburetor throttle lever. Move throttle control
to FAST position.
GOVERNED
IDLE SPRING
(RED OR WHITE)
CASING
CLAMP
Note: Engines operated at approximately 3000 to 5000 feet
above sea level may requirea high altitudecarburetormain jet.
See a Briggs & Stratton Dealer.
ON NG / LPG Powered Engines
Adjusting Fuel Mixer
If adjustment is needed, see a Briggs & Stratton Authorized
Service Dealer who has been licensed by the state or local
municipality (if required) in which the service is performed.
Mixer adjustment requires special equipment and a qualified
technician. DO NOT remove limiter caps. DO NOT force
beyond limits.
GB
5
Adjustments Cont’d (see fig. ¦)
Choke control adjustments
Remove air cleaner . Move choke control to CHOKE position.
Carburetor choke valve
should be completely closed. If not,
loosen casing clamp screw
and pull casing and wire in
direction of arrow to end of travel. T i ghten casing clamp screw .
Replace air cleaner.
Throttle control adjustments
Remove air cleaner. Move throttle control to FAST position.
Swivel
should be against throttle stop . If not, loosen
casing clamp screw
. Move casing and wire in direction
shown by arrow until swivel is against throttle stop. Tighten
casing clamp screw. Check operation of controls. Readjust if
necessary. Replace air cleaner.
Adjustable Governor Control
This control was set according to requirements of
manufacturer of the equipment on which this engine is
installed. If adjustment is required, consult any Briggs &
Stratton Authorized Service Dealer.
Storage
Engines stored over 30 days need to be protected or drained of
fuel to prevent gum from forming in fuel system or on essential
carburetor parts.
For engine protection, we recommend use of Briggs & Stratton
Fuel Stabilizer available from an Authorized Briggs & Stratton
Service Dealer. Mix stabilizer with fuel in fuel tank or storage
container. Run engine for a short time to circulate stabilizer
through carburetor. Engine and fuel can be stored up to 24
months.
Note: If stabilizer is not used or if engine is operating on
gasoline containing alcohol, e.g. gasohol, remove all fuel from
tank and run engine until it stops from lack of fuel.
1. Change oil. See Oil service. (see figs.
©¦)
2. Remove spark plugs and pour about 30 ml (1 oz) of
engine oil into cylinders. Replace spark plugs and crank
slowly to distribute oil.
3. Clean chaff or debris from cylinders and cylinder head
fins and behind muffler.
4. Store in a clean and dry area, but NOT near a stove,
furnace or water heater which uses a pilot light or any
device that can create a spark.
Service
See an Authorized Briggs & Stratton Service Dealer.Each one
carries a stock of Genuine Briggs & Stratton Parts and is
equipped with special service tools. Trained mechanics
assure expert repair service on all Briggs & Stratton engines.
Only dealers advertising as “Authorized Briggs & Stratton” are
required to meet Briggs & Stratton standards.
When you purchase equipment powered by a
Briggs & Stratton engine, you are assured of
highly skilled, reliable service at more than
30,000 Authorized Service Dealers world-
wide, including more than 5,000 Master
Service Technicians. Look for these signs
wherever Briggs & Stratton service is offered.
You may locate your nearest Authorized Briggs & Stratton
Service Dealer in our dealer locator map on our web site
www.briggsandstratton.com or in the “Yellow
Pages directory under “Engines, Gasoline”
or “Gasoline Engines,” or “Lawn Mowers” or
similar category.
Note: Walking fingers logo and “Yellow Pages” are registered
trademarks in various jurisdictions.
An illustrated shop manual includes “Theories of Operation,”
common specifications and detailed information covering
adjustment, tune-up and repair of Briggs & Stratton V-Twin
cylinder OHV, 4 cycle engines. Order P/N 272144 from an
Authorized Briggs & Stratton Service Dealer.
Insiston Genuine Briggs & Strattonreplacement parts withour
logoon the box and/or part.Non-originalparts may not perform
as well and may void your warranty.
Partial List of Genuine Briggs & Stratton Parts
Briggs & Stratton (or
equivalent)
Part Part No.
Oil (20 oz.) 100005.............................
Oil (48 oz.) 100028.............................
Oil filter (6 cm long) 492932 (5049).................
Oil filter (9 cm long) 491056.......................
Oil pump kit (uses standard electric drill 5056.........
to remove oil from engine quickly)
Fuel stabilizer (1 oz., 30 ml single use pouch) 992030....
Fuel stabilizer (4.2 oz., 125 ml bottle) 999005E (5041)...
Fuel filter (without fuel pump) 298090 (5018)..........
Fuel filter (with fuel pump) 493629..................
Fuel filter (with 9 qt. fuel tank on engine) 808116........
Air cleaner cartridge 393957......................
(with 9 qt. fuel tank on engine)
Air cleaner pre-cleaner 271794.....................
(with 9 qt. fuel tank on engine)
Air cleaner cartridge 394018......................
(all other models except model 380000)
Air cleaner pre-cleaner 272490.....................
(all other models except model 380000)
Air cleaner (cartridge and pre-cleaner kit) 5050........
(all other models except model 380000)
Air cleaner cartridge (model 380000) 692519...........
Air cleaner pre-cleaner (model 380000) 692520.........
Resistor spark plug 491055 or 496018...............
Long life platinum spark plug 5066.................
(used on most OHV engines)
Spark tester 19368.............................
Spark plug wrench 19374........................
Spark arrester 392390...........................
Resistor spark plug 491055 or 496018...............
GB
6
BRIGGS & STRATTON ENGINE OWNER WARRANTY POLICY
Effective July 1, 2004 replaces all undated Warranties and all Warranties dated before July 1, 2004
LIMITED WARRANTY
Briggs&StrattonCorporation will repair or replace, free of charge,anypart(s)oftheengine that is defective in materialorworkmanshiporboth.Trans-
portation charges on parts submitted for repair or replacement under this warranty must be borne by purchaser.This warranty is effective for the time
periods and subject to the conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at
www.briggsandstratton.com
, or by calling 1-800-233-3723, or as listed in the ‘Yellow Pages’.
THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABIL ITY AND FITNESS FOR A PAR-
TICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW ANY AND ALL IMPLI ED WAR-
RANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL D AMAGES ARE EXCLUDED TO THE EXTENT EXCL USION IS
PERMITTED BY LAW. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not
allow theexclusionorlimitationof incidentalor consequentialdamages,s o theabove limitationand exclusionmay notapply toyou.Thiswarranty gives
you specific legal rights and you may also have other rights which vary from state to state and country to country.
Vanguard
ELS
I/Cr
Industrial Plus
Intek
(Sleeve Bore)
Fource
Intek
(Kool Bore)
Power Built OHV
Quantumr
Quattro
Q45
Sprint
Classic
Commercial Use
2 years
90 days
1 year
Consumer Use
2 years
2 years
90 days
1 year
OUR PRODUCT
WARRANTY PERIOD*
Etek
1 year
* Note the following special warranty periods: 2 years for Classic engines in the European Union and Eastern European countries, for all consumer products in the European Union, and
for e mission control systems on engines certified by EPA and CARB. 5 years for consumer use, 90 days for commercial use of Touch-N-Mow starter on Quantum and Intek engines.
Engines used in competitive racing or on commercial or rental tracks are not warrantied.
The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated in the table above. “Consumer use”
means personal residential household use by a retail consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once an
engine has experienced commercial use, it shall thereafter be considered as a commercial use engine for purposes of this warranty.
NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR PROOF OF PURCHASE RECEIPT. IF
YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED, THE MANUFACTURING DATE OF THE
PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.
ABOUT YOUR ENGINE WARRANTY
Briggs & Stratton welcomes warranty repair and apologizes to
you for being inconvenienced. Any Authorized Service Dealer
may perform warranty repairs. Most warranty repairs are han-
dled routinely, but sometimes requests for warranty service
may not be appropriate. For example, warranty would not apply
if engine damage occurred because of misuse, lack of routine
maintenance, shipping, handling, warehousing or improper
installation. Similarly, warranty is void if the serial number of the
engine has been removed or the engine has been altered or
modified.
If a customer differs with the decision of the Service Dealer, an
investigation will be made to determine whether the warranty
applies. Ask the Service Dealer to submit all supporting facts to
his Distributor or the F actory for review. If the Distributor or the
Factory decides that the claim is justified, the customer will be
fully reimbursed for those items that are defective. To avoid mis-
understanding which might occur between the customer and
the Dealer, listed below are some of thecauses of engine failure
that the warranty does not cover.
Normal wear:
Engines, like all mechanical devices, need periodic parts service
and replacement to perform well. Warranty will not cover repair
when normal use has exhausted the life of a part or an engine.
Improper maintenance:
Thelife of an engine depends upon the conditions under which it
operates, and the care it receives. Some applications, such as
tillers, pumps and rotary mowers, are very often used in dusty or
dirty conditions, which can cause what appears to be premature
wear. Such wear, when caused by dirt, dust, spark plug cleaning
grit, or other abrasive material that has entered the engine be-
cause of improper maintenance, is not covered by warranty.
Thiswarrantycoversenginerelateddefective material and/
or workmanship only, and not replacement or refund of the
equipment to which the engine may be mounted. Nor does
the warranty extend to repairs required because of:
1. PROBLEMS CAUSED BY PARTS THAT ARE NOT
ORIGINAL BRIGGS & STRATTON PARTS.
2. Equipment controls or installations that prevent starting,
cause unsatisfactory engine performance, or shorten en-
gine life. (Contact equipment manufacturer.)
3. Leaking carburetors, clogged fuel pipes, sticking valves,
or other damage, caused by using contaminated or stale
fuel. (Use clean, fresh, lead-free gasoline and Briggs &
Stratton Fuel Stabilizer, Part No. 5041.)
4. Parts which are scored or broken because an engine was
operated with insufficient or contaminated lubricating oil,
or an incorrect grade of lubricating oil (check oil level daily
or after every 8 hours of operation. Refill when necessary
and change at recommended intervals.) OIL GARD
may not shut down running engine. Engine damage may
occur i f oil level is not properly maintained. Read Operat-
ing & Maintenance Instructions.
5. Repair or adjustment of associated parts or assemblies
such as clutches, transmissions, remote controls, etc.,
which are not manufactured by Briggs & Stratton.
6. Damage or wear to parts caused by dirt, which entered
the engine because of improper air cleaner maintenance,
re-assembly, or use of a non-original air cleaner element
or cartridge. (At recommended intervals, clean and re-oil
the Oil-Foam element or the foam pre-cleaner, and
replace the cartridge.) Read Operating & Maintenance
Instructions.
7. Parts damaged by over-speeding, or overheating caused
by grass, debris, or dirt, which plugs or clogs the cooling
fins, or flywheel area, or damage caused by operating the
engine in a confined area without sufficient ventilation.
(Clean fins on the cylinder, cylinder head and flywheel at
recommendedintervals.) Read Operating &Maintenance
Instructions.
8. Engine or equipment parts broken by excessive vibration
caused by a loose engine mounting, loose cutter blades,
unbalanced blades or loose or unbalanced impellers, im-
proper attachment of equipment to engine crankshaft,
over-speeding or other abuse in operation.
9. A bent or broken crankshaft, caused by striking a solid ob-
ject with the cutter blade of a rotary lawn mower, or exces -
sive v-belt tightness.
10. Routine tune-up or adjustment of the engine.
11. Engine or engine component failure, i.e., combustion
chamber, valves, valve seats, valve guides, or burned
starter motor windings, caused by the use of alternate
fuels such as, liquified petroleum, natural gas, altered
gasolines, etc.
Wa rranty is available only through service dealers which
have been authorized by Briggs & Stratton Corporation.
your nearest Authorized Service Dealer is listed in the “Y el-
low Pages of your telephone directory under “Engines,
Gasoline” or “Gasoline Engines,” “Lawn Mowers,” or simi-
lar category.
GB
7
Briggs & Stratton Engines Are Made Under One Or More Of The Following Patents: Design D-247,177 (Other Patents Pending)
6,691,683
6,647,942
6,622,683
6,615,787
6,617,725
6,603,227
6,595,897
6,595,176
6,584,964
6,557,833
6,542,074
6,520,141
6,495,267
6,494,175
6,472,790
6,460,502
6,456,515
6,382,166
6,369,532
6,356,003
6,349,688
6,347,614
6,325,036
6,311,663
6,284,123
6,263,852
6,260,529
6,242,828
6,239,709
6,237,555
6,230,678
6,213,083
6,202,616
6,145,487
6,142,257
6,135,426
6,116,212
6,105,548
6,347,614
6,082,323
6,077,063
6,064,027
6,040,767
6,014,808
6,012,420
5,992,367
5,904,124
5,894,715
5,887,678
5,852,951
5,843,345
5,823,153
5,819,513
5,813,384
5,809,958
5,803,035
5,765,713
5,732,555
5,645,025
5,642,701
5,628352
5,619,845
5,606,948
5,606,851
5,605,130
5,497,679
5,548,955
5,546,901
5,445,014
5,503,125
5,501,203
5,497,679
5,320,795
5,301,643
5,271,363
5,269,713
5,265,700
5,243,878
5,235,943
5,234,038
5,228,487
5,197,426
5,197,425
5,197,422
5,191,864
5,188,069
5,186,142
5,150,674
5,138,996
5,086,890
5,070,829
5,058,544
5,040,644
5,009,208
4,996,956
4,977,879
4,977,877
4,971,219
4,895,119
4,875,448
4,819,593
4,720,638
4,719,682
4,633,556
4,630,498
4,522,080
4,520,288
4,512,499
4,453,507
4,430,984
D 476,629
D 457,891
D 368,187
D 375,963
D 309,457
D 372,871
D 361,771
D 356,951
D 309,457
D 308,872
D 308,871
¦
§¨
0.030”
(.76mm)
(This page applicable in the U.S.A. and Canada only.)
Briggs & Stratton Corporation (B&S), the California Air Resources Board (CARB)
and the United States Environmental Protection Agency (U.S. EPA)
Emission Control System Warranty Statement (Owner’s Defect Warranty Rights and Obligations)
EMISSION CONTROL WARRANTY COVERAGE IS APPLICABLE TO CERTIFIED ENGINES PUR-
CHASED IN CALIFORNIA IN 1995 AND THEREAFTER, WHICH ARE USED IN CALIFORNIA, AND
TO CERTIFIED MODEL YEAR 1997 AND LA TER ENGINES WHICH ARE PURCHASED AND USED
ELSEWHERE IN THE UNITED STATES (AND AFTER jANUARY 1, 2001 IN CANADA).
California, United States and Canada Emission Control Defects Warranty Statement
The California Air Resources Board (CARB), U.S. EPA and B&S are pleased to explain the Emission
Control System Warranty on your model year 2000 and later small off-road engine (SORE). In Califor-
nia, new small off-road engines must be designed, built and equipped to meet the State’s stringent anti-
smog standards. Elsewhere in the United States, new non-road, spark-ignition engines certified for
model year 1997 and later, must meet similar standards set forth by the U.S. EP A. B&S must warrant
the emission control system on your engine for the periods of time listed below ,provided there has been
no abuse, neglect or improper maintenance of your small off-road engine.
Your emission control system includes parts such as the carburetor, air cleaner, ignition system,
muffler and catalytic converter. Also included may be connectors and other emission related as-
semblies.
Where a warrantable condition exists, B&S will repair your small off-road engine at no cost to you
including diagnosis, parts and labor.
Briggs & Stratton Emission Control Defects Warranty Coverage
Small off-road engines are warranted relative to emission control parts defects for a period of two
years, subject to provisions set forthbelow.If any covered part on your engine is defective, the part
will be repaired or replaced by B&S.
Owner’s Warranty Responsibilities
Asthesmall off-roadengineowner,youareresponsibleforthe performanceofthe requiredmainte-
nance listed in your Operating and Maintenance Instructions. B&S recommends that you retain all
your receipts covering maintenance on your small off-road engine, but B&S cannot deny warranty
solely for the lack of receipts or for your failure to ensure the performance of all scheduled mainte-
nance.
Asthe smalloff-road engineowner,you shouldhowever beawarethatB&Smaydenyyou warranty
coverage if your small off-road engine or a part has failed due to abuse, neglect, improper mainte-
nance or unapproved modifications.
You are responsible for presentingyoursmall off-roadenginetoan Authorized B&SServiceDealer
assoon asa problemexists.The undisputed warrantyrepairs shouldbecompleted inareasonable
amount of time, not to exceed 30 days.
If you have anyquestions regarding your warranty rights and responsibilities, you should contact a
B&S Service Representative at 1-414-259-5262.
The emission warranty is a defects warranty. Defects are judged on normal engine performance.
The warranty is not related to an in-use emission test.
Briggs & Stratton Emission Control Defects Warranty Provisions
The following are specific provisions relative to your Emission Control Defects Warranty Coverage. It is in addition to the B&S engine warranty for non-regulated engines found in the Operating and Maintenance Instructions.
1. Warranted Parts
Coverage under this warranty extends only to the parts listed below (the emission control
systems parts) to the extent these parts were present on the engine purchased.
a. Fuel Metering System
Cold start enrichment system (soft choke)
Carburetor and internal parts
Fuel Pump
b. Air Induction System
Air cleaner
Intake manifold
c. Ignition System
Spark plug(s)
Magneto ignition system
d. Catalyst System
Catalytic converter
Exhaust manifold
Air injection system or pulse valve
e. Miscellaneous Items Used in Above Systems
Vacuum, t emperature, position, time sensitive valves and switches
Connectors and assemblies
2. Length of Coverage
B&S warrants to the initial owner and each subsequent purchaser that the Warranted Parts
shall be free from defects in materials and workmanship which caused the failure of the War-
rantedParts for a period of two years from the date the engine is delivered to a retailpurchaser.
3. No Charge
Repair or replacement of any Warranted Part will be performed at no charge to the owner, in-
cluding diagnostic labor which leads to the determination that a WarrantedPart is defective, if
thediagnostic workis performedatanAuthorized B&SService Dealer.Foremissions warranty
service contact your nearest Authorized B&S Service Dealer as listed in the “Yellow Pages”
under “Engines, Gasoline,” “Gasoline Engines,” “Lawn Mowers,” or similar category.
4. Claims and Coverage Exclusions
Warranty claims shall be filed in accordance with the provisions of the B&S Engine Warranty
Policy. Warrantycoverage shall be excluded forfailuresofWarrantedPartswhich are not origi-
nal B&S parts or because of abuse, neglect or improper maintenance as set forth in the B&S
Engine Warranty Policy. B&S is not liable to cover failures of Warranted Parts caused by the
use of add-on, non-original, or modified parts.
5. Maintenance
AnyWarrantedPart which isnot scheduled for replacement as required maintenance or which
isscheduledonlyfor regular inspectiontotheeffectof“repairorreplace asnecessary” shall be
warranted as to defects for the warranty period. Any Warranted Part which is scheduled for
replacement as required maintenance shall be warranted as to defects only for the period of
timeupto the first scheduled replacement forthat part. Any replacement part that isequivalent
in performance and durability may be used in the performance of any maintenance or repairs.
The owner is responsible for the performance of all required maintenance, as defined in the
B&S Operating and Maintenance Instructions.
6. Consequential Coverage
Coveragehereundershall extendto thefailureof anyengine componentscaused bythe failure
of any Warranted Part still under warranty.
Look For Relevant Emission Durability Period and Air Index Information On Your Engine Emission Label
Engines that are certified to meet the California Air Resources Board (CARB) Tier 2 Emission Standards must display information regarding the EmissionsDurability Period and the Air Index. Briggs & Stratton
makes this i nformation available to the consumer on our emission labels. The engine label will indicate certification information.
TheEmission DurabilityPerioddescribes the number of hoursofactualrunningtime for which the engineis certifiedtobeemissioncompliant,assuming proper maintenanceinaccordancewitht he Operating
& Maintenance Instructions. The following categories are used:
Moderate: Engine is certified to be emission compliant for 125 hours of actual engine running time.
Intermediate: Engine is certified to be emission compliant for 250 hours of actual engine running time.
Extended: Engine is certified to be emission compliant for 500 hours of actual engine running time.
For example, a typical walk-behind lawn mower is used 20 to 25 hours per year. Therefore, the Emission Durability Period of an engine with an intermediate ratingwouldequateto10to12years.
The Air Index is a calculated number describing the relative level of emission for a specific engine family. The lower the Air Index, the cleaner the engine. This information is displayed in graphical form on the
emission label.
After July 1, 2000, Look For Emissions Compliance Period On Engine Emissions Compliance Label
After July 1, 2000 certain Briggs & Stratton engines will be certified t o meet the United Sattes Environmental Protecteion Agency (USEPA) Phase 2 emission standards. For Phase 2 certified engines, the
EmissionsCompliancePeriodreferred to on the Emissions Compliance l abel indicates the number of operating hours for which theengine has been shown to meet Federal emissionrequirements. For engines
less than 225 cc displacement, Category C = 125 hours, B = 250 hours and A = 500 hours. For engines of 225 cc or more, Category C = 250 hours, B = 500 hours and A = 1000 hours.
The displacement of Model Series 290000 and 300000 engines is 480 cc. The displac ement of Model Series 350000 engines is 570 cc. The displacement of Model Series 380000 engines is 627 cc.
This is a generic representation
of the emission label typically
found on a certified engine.
(Cette page ne s’applique que pour le Canada et les Etats--Unis)
La Corporation Briggs & Stratton (B&S), le California Air Resources Board (CARB)
et le Bureau de protection environnementale des Etats-Unis (US EPA)
Garantie sur le système d’échappement (Garantie contre les défectuosités, droits et obligations du propriétaire)
LA GARANTIE SUR LE SYSTÈME D’ÉCHAPPEMENT EST APPLICABLE SUR LES MOTEURS
CERTIFIÉSACHETÉS EN CALIFORNIE EN 1995 ET LES ANNÉES SUIV ANTESET QUI SONT UTI-
LISÉS EN CALIFORNIE, AINSI QU’AUX MODÈLES CERTIFIÉS DE 1997 ET LES ANNÉES SUI-
VANTES QUI ONT ÉTÉ ACHETÉS ET UTILISÉS AILLEURS AUX ETATS--UNIS ET AU CANADA.
Déclaration de garantie sur le système d’échappement pour la Californie, les Etats-Unis et le Canada
Le California Air Resources Board (CARB), le Bureau américain de protection environnementale
(U.S. EPA) et B& S sont heureux d’expliquer la garantie sur le système d’échappement des petits
moteurs hors--route de votre modèle 2000 et des années ultérieures (SORE). En Californie, les
nouveaux petits moteurs hors route doivent être conçus, construits et équipés pour rencontrer les
standards rigoureux d’antipollution. Ailleurs aux Etats--Unis, les nouveaux moteurs hors route à
bougie d’allumage certifiés pour les modèles de 1997 et plus, doivent rencontrer des normes simi-
laires mises de l’avant par le U.S. EPA. Briggs & Stratton garantit le système de contrôle d’échap-
pement de votre moteur pour la période de temps mentionnée ci--contre, sauf s’il a fait l’objet
d’abus, de négligence ou d’un entretien inapproprié.
Votresystème decontrôled’échappement comprend despièces telles quelecarburateur,le filtreà
air, le système d’ignition, le silencieux et le convertisseur catalytique. Il peut aussi comprendre les
connecteurs et autres pièces reliées à l’émission.
Lorsqu’ily acondition à garantie,B&Srépareragratuitementvotrepetit moteurhors--routeincluant
le diagnostic, les pièces et la main d’œuvre.
Couverture de garantie Briggs & Stratton contre toute défectuosité du système de contrôle d’échappement
Lespetits moteurshors routesont garantiscontreladéfectuositédespiècesdusystème decontrô-
led’échappementpourunepériodede2ans,sujetteaux conditionsstipuléesci--contre.Sin’impor-
te quelle pièce de votre moteur couverte par cette garantie est défectueuse, elle sera réparée ou
remplacée par B&S.
Responsabilités du propriétaire
Entant que propriétaire d’un petit moteur hors route, vous êtes responsable de veilleràl’exécution
de l’entretien requis t el que stipulé dans votre manuel d’opération et d’entretien. B&S vous recom-
mande de conserver tousles reçus couvrant les travaux d’entretien de votre petit moteur hors rou-
te, mais B&S ne peut refuser la garantie en raison d’absence de reçus ou pour défaut d’avoir suivi
tout l’échéancier du programme d’entretien.
Entant quepropriétaired’un petitmoteurhors route,vousdevez êtreinformé queB&Speutrefuser
d’honorercette garantiesi ladéfectuositéde votremoteurou d’unepartiedevotremoteurestdueà
un emploi abusif, une négligence, un entretien incorrect ou une modification non approuvée.
Vous avez la responsabilité d’apporter votre petit moteur hors route à un détaillant autorisé B&S
aussitôtquesurvient un problème. Les réparationssous garantie doivent être complétées dans un
délai raisonnable ne devant pas excéder 30 jours.
Si vous avez des questions relativement à votre garantie, vos droits et responsabilités, veuillez
communiquer avec un représentant de service B&S au numéro 1--414--259--5262.
La garantie du système d’échappement est une garantie contre les défectuosités.Les défectuosi-
tés sont jugées en fonction d’une utilisation normale du moteur. La garantie n’est pas reliée à un
test d’échappement effectué à l’intérieur.
Dispositions de la garantie du système d’échappement Briggs & Stratton
Ce qui suit concerne les dispositions spécifiques relativement à votre garantie sur le système de contrôle d’échappement. C’est une addition à la garantie B&S pour les moteurs non réglementés contenue
dans le manuel d’entretien et d’utilisation.
1. Pièces sous garantie
La couverture de cette garantie ne s’applique que sur les pièces listées ci--contre (les parties
dusystèmedecontrôled’échappement ) dans la mesure ces piècesétaientprésentessurle
moteur au moment de l’achat.
a. Système de dosage du carburant
Système d’enrichissement de démarrage à froid
Carburateur et parties internes
Pompeàessence
b. Système d’induction d’air
Filtre à air
Tubulure d’admission
c. Système d’ignition
Bougies d’allumage
Système d’allumage électromagnétique
d. Système catalyseur
Convertisseur catalytique
Collecteur d’échappement
Système d’injection d’air ou à pulsion
e. Autres pièces utilisées dans les systèmes ci--haut mentionnés
Soupapes et interrupteurs de dépression, de température, de position.
Connecteurs et assemblages.
2. Duréedelacouverture
B&S garantit le propriétaire initial et tous les acheteurs subséquents que les pièces sous ga-
rantiesontexemptesdevice dematièreoudefabricationquipourraientcauserdesdéfectuosi-
tés des pièces sous garantie pour une période de deux ans à partir de la date à laquelle le mo-
teur a été livré à l’acheteur.
3. Aucuns Frais
La réparation ou le remplacement de toute pièce sous garantie sera effectuée sans aucuns
frais pour le propriétaire, incluant les frais de main d’œuvre pour le diagnostic afin de détermi-
ner si la pièce sous garantie est défectueuse, conditionnel à ce que le diagnostic soit effectué
chezun détaillant autoriséB&S. Pourlagarantierelativeausystèmed’échappement,commu-
niquez avec le détaillant autorisé B&S le plus proche tel que listé dans les pages jaunes de
votre localité sous la rubrique moteur à essence, tondeuse ou autre catégorie similaire.
4. Réclamations et exclusions de la couverture.
Les réclamations de garantie doivent être complétées en accord avec les dispositions de la
politique de garantie B&S. La garantie ne couvre pas les défectuosités de pièces qui ne sont
pas des pièces d’origine B&S ou dans le cas d’abus, négligence oud’un entretien inapproprié.
La garantie B&S ne couvre pas les défectuosités de pièces sous garantie qui ont fait l’objet
d’ajouts, ont été modifiées ou de pièces qui ne sont pas des pièces B&S d’origine.
5. Entretien
Toute pièce sous garantie qui n’est pas remplacée au moment requis selon le manuel d’entre-
tien ou qui est planifiée seulement pour une inspection régulière sous la mention « réparer ou
remplacer si nécessaire » est garantie contre toute défectuosité pour la période de garantie.
Toute pièce sous garantie qui est planifiée pour un remplacement tel que requis dans l’entre-
tien est garantie contre toute défectuosité seulement pour la période de temps qui va jusqu’au
premier remplacement prévu pour cette pièce. Toute pièce de remplacement équivalente en
performance et durabilité peut être utilisée pour l’entretienou la réparation. Le propriétaire est
responsable de l’exécution de tout entretien requis tel que défini dans le manuel d’instruction
B&S sur l’entretien et la réparation.
6. Couverture indirecte
La couverture ci--contre s’étend à toute défectuosité des composantes du moteur causée par
ladéfectuositéde n’importe quelle pièce couverte par lagarantie et dont la garantie est encore
en vigueur.
Consultez les informations sur la période de durabilité d’émission et l’INDICE d’air sur l’étiquette d’émission de votre moteur
Les moteurs qui sont certifiés conformes aux normes standards d’émission du California Air Resources Board (CARB) Tier 2, doivent afficher l’information concernant la période de durabilité du système
d’émission et l’INDICE d’air. Cette information est indiquée sur les étiquettes apposées sur les moteurs par Briggs & Stratton. L’étiquette du moteur indiquera les renseignements concernant la certification.
Lapériodededurabilitéd’émissionindiquelenombred’heuresd’utilisationnormalepourlequellemoteurestcertifiéconformeauxnormesd’émissionsousréserved’unentretienappropriételqu’indiquédans
le manuel d’opération et d’entretien. Les catégories suivantes sont utilisées :
Modéré le moteur est certifié conforme pour 125 heures d’utilisation normale.
Intermédiaire le moteur est certifié conforme pour 250 heures d’utilisation normale.
Prolongé le moteur est certifié conforme pour 500 heures d’utilisation normale.
Parexemple, une tondeuse de modèle standardestutiliséeenviron 20 à 25 heuresparannée.Parconséquent, la période de durabilitéd’émission d’unmoteurdansla catégorieintermédiairepour ce typede
tondeuse équivaut à 10 à 12 ans.
L’indice d’air est un nombre qui décrit le niveau relatif d’émission pour une catégorie spécifique de moteur. Plus l’indice d’air est bas, plus le moteur est écologique. Cette information est indiquée sous une
forme graphique sur l’étiquette d’émission.
À compter du 1
er
juillet 2000, surveillez la p ériode de conformité d’émission sur les étiquettes
Après le 1
er
juillet 2000, certains moteurs B&S seront certifiés conformes aux normes environnementales d’émission standard du United States Environmental Protection Agency (US EPA) Phase 2. Pour les
moteurs certifiés pour la Phase 2, la période de conformité d’émission mentionnée sur les étiquettes indique le nombre d’heures d’utilisation pour lequel le moteur rencontre les normes fédérales. Pour les
moteurs de force moindre que 225 cc, la catégorie C = 125 heures, B = 250 heures et A = 500 heures. Pour les moteurs de 225 cc et plus, la catégorie C = 250 heures, B = 500 heures et A = 1000 heures.
Leremplacement du moteur portantlemodèlede série290000et300000 est 480 cc.Leremplacement du moteurportantlemodèle de série350000est 570 cc. Leremplacementdumoteur portant lemodèlede
série 380000 est 627 cc.
Ceci est une représentation des étiquettes d’émission
que vous retrouverez sur les moteurs certifiés :
CE MOTEUR EST CONFORME AUX NORMES
ANTIPOLLUTION 2000 -- 2001 DE CALIFORNIE
POUR LES PETITS MOTEURS HORS ROUTE ET
AUX NORMES ENVIRONNEMENTALES
AMÉRICAINES (EPA PHASE 2) POUR LES
PETITS MOTEURS HORS ROUTE. CONSULTEZ
LE MANUEL DU PROPRIÉTAIRE POUR LES
SPÉCIFICATIONS, L’ENTRETIEN ET LES
AJUSTEMENTS. CONFORME À LA RIODE
D’ÉMISSION EPA : CATÉGORIE : C
FAMILLE YBSXS.3192VA 274812
INFORMATIONS IMPORTANTES
CORPORATION BRIGGS & STRATTON
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Simplicity 305447-0115-E1 Manuel utilisateur

Catégorie
Accessoires pour véhicules automobiles
Taper
Manuel utilisateur

dans d''autres langues