Frigidaire FFRE1001PW0 Guide d'installation

TABLE OF CONTENTS

Important Safety Instructions ........................... 2-3 Accessories ...................................................... 19

Installatton Requirements .............................. 4-10 Notes ............................................................. 20

Installabon Instructions ................................ 11-16 Fran_als .......................................................... 21

Reversmg Door ............................................ 17-18 Espa_ol ........................................................... 41

oo

3>

oo

For your safety the information in this manual must be followed to minimize the risk of fire or explosion or to prevent

property damage, personal injury or loss of life. Do not store or use gasoline or other flammable vapors and liquids in

....the vidnity °f th!s °! any °ther app!!ance:......................................................................................................................................................................................................................................................................................................................

AWARNING - RISK OF FIRE

Read all of the following instructions before installing and using this appliance:

* Destroy the carton and plastic bags after the dryer is unpacked. Children might use them for play. Cartons covered

with rugs, bedspreads, or plastic sheets can become airtight chambers causing suffocation. Place all materials in a

garbage container or make materials inaccessible to children.

* Clothes dryer installation and service must be performed by a qualified installer, service agency or the gas supplier.

* Install the clothes dryer according to the manufacturer's instructions and local codes.

* The electrical service to the dryer must conform with local codes and ordinances and the latest edition of the

National Electrical Code, ANS[/NFPA 70, or in Canada, the Canadian electrical code C22.I part 1.

* The gas service to the dryer must conform with local codes and ordinances and the latest edition of the National

Fuel Gas Code ANSI Z223.1, or in Canada, CAN/ACG BI49.1-2000. An individual manual shut-off valve must be

installed within 6 ft (i.83 m) of the dryer in accordance with the National Fuel Gas Code, ANSI Z223.1/NFPA 54.

* The dryer is designed under ANSI Z 21.5.1 or ANS[/UL 2158 - CAN/CSA C22.2 No. i12 (latest editions) for HONE

USE only. This dryer is not recommended for commercial applications such as restaurants, beauty salons, etc.

* Do not install a clothes dryer with flexible plastic or flexible foil venting material. Flexible venting materials are

known to collapse, be easily crushed and trap lint. These conditions will obstruct clothes dryer airflow and increase

the risk of fire.

* The instructions in this manual and all other literature included with this dryer are not meant to cover every

possible condition and situation that may occur. Good safe practice and caution NUST be applied when installing,

operating and maintaining any appliance.

WHAT TO DO IF YOU SMELL GAS:

* Do not try to light any appliance.

* Do not touch any electrical switch; do not use any

phone in your building.

* Clear the room, building or area of all occupants.

* Immediately call your gas supplier from a neighbor's

phone. Follow the gas supplier's instructions.

* If you cannot reach your gas supplier, call the fire

department.

personmoveor !!Ittheapp!iance: ..................

Save these instructions

for future reference.

Pre-Installation Requirements

Tools and materials needed for installation:

* Adjustable pliers * Carpenter's level

* Phillips, straight, & square bit * External vent hood

screwdrivers * 4-inch (!02 mm), rigid metal or

* Adjustable wrench semi-rigid metal exhaust duct work

* Pipewrench for gas supply (gas * 3-wire or 4-wire 240 volt cord kit

dryer) (electric dryer)

* @-resistant thread tape (for natural * 4 in. (!02 mm) clamp

gas or LPsupply, gas dryer)

* Gas line shutoff valve (gas dryer)

* _/2NPTunion flare adapters (x2)

and flexible gas supply line (gas

dryer)

Netal foil tape (not duct tape)

Pleasereadallinstructionsbeforeusingthisdryer.

Recognize safety syrnboisr words

and labels

Safety items throughout this manual are labeled with

a WARNING or CAUTION based on the risk type as

described below:

Definitions

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards. Obey all safety

messages that follow this symbol to avoid possible injury

or death.

DANGER indicates an imminently hazardous situation

Exhaust Venting

Free-flowing, clear of lint buildup

4 inch (102 mm) rigid or semi-rigid ducting of

minimal length and turns

E_ NOfoil or plastic venting material

E_ Approved vent hood exhausted to outdoors

Leveling

E_ Dryer is level, side-to-side and front-to-back

E3 Cabinet is setting solid on all corners

GasSupplyCGasDryer:

E_ Manual shutoff valve present in supply

E_ AIt connections sealed with approved sealer and

wrench tight

E_ Conversion kit for LPsystem

E_ Gas supply turned on

E3 No leaks present at all connections -

check with soapy water, NEVERcheck with flame

which if not avoided will result in death or serious

injury, 240v Electric Supply (Electric Dryer)

E3 Approved NEMA 10-30R or 14-30R service cord

with all screws tight on terminal block

E3 Approved strain relief installed

E3 Terminal access cover installed before initial

operation

Door Reversal

E3 Follow detailed instructions in this guide

CAUTION indicates a potentially hazardous situation E3 Test hinge and latch for function

which, if not avoided, may result in minor or moderate

injury. Electrical Power

E3 House power turned on

IMPORTANT indicates installation, operation or

maintenance information which is important but not

hazard-related.

E3 Dryer plugged in

Final Checks

Installation Instructions and Use and Care

Guide read thoroughly

Door latches and drum tumbles when cycle

starts

Registration card sent in

Becauseofpotentiallyinconsistentvoltagecapabilities,theuseofthisdryerwithpowercreatedbygaspowered

generators,solarpoweredgenerators,windpoweredgeneratorsoranyothergeneratorotherthanthelocalutility

companyisnotrecommended,

Electrical requirements for electric dryer

CIRCUIT - Individual 30 amp. branch circuit fused with 30 amp. time delay fuses or circuit breakers. Use separately

fused circuits for washer and dryer. DO NOT operate a washer and a dryer on the same circuit.

POWER SUPPLY- 3-wire or 4-wire, 240 volt, single phase, 60 Hz, Alternating Current.

through the neutral.

OUTLET RECEPTACLE- NEMA 10-3ORor NEMA 14-30R rece )tacie to be located so the power supply cord is accessible

when the dryer is in the installed position.

GROUNDING CONNECTION - See "Grounding requirements" in Electrical Installation section.

3-WIRE POWERSUPPLYCORD KIT (not supplied)

3-wire receptacle

(NEMA type 10-30R)

The dryer MUSTemploy a 3-conductor power

supply cord NEMA 10-30 type SRDTrated at 240

volt AC minimum, 30 amp, with 3 open end spade

lug connectors with upturned ends or closed

loop connectors and marked for use with clothes

dryers. For 3-wire cord connection instructions see

ELECTRICALCONNECTIONS FOR A 3-WIRE SYSTEM.

4-WIRE POWER SUPPLYCORD KIT (not supplied)

4-wire receptacle

(NEMA type 14-30R)

The dryer MUST employ a 4-conductor power supply

cord NEMA 14-30 type SRDTor ST (as required) rated

at 240 volt AC minimum, 30 amp, with 4 open end

spade lug connectors with upturned ends or closed

loop connectors and marked for use with clothes

dryers. For 4-wire cord connection instructions see

ELECTRICALCONNECTIONS FORA 4-WIRE SYSTEM.

Electrical requirements for gas dryer

CIRCUIT - Individual, properly polarized and grounded

15 amp. branch circuit fused with 15 amp. time delay

fuse or circuit breaker.

POWER SUPPLY- 2-wire, with ground, !20 volt, single

phase, 60 Hz, Alternating Current.

POWER SUPPLYCORD - The dryer is equipped with a 120

volt 3-wire power cord.

GROUNDING CONNECTION - See "Grounding

requirements" in Electrical Installation section.

Groundingtype

wal receptacle

_- Do not,under -"

/ _.\ I |anycircurnstances

\ I_ grounding prong.

h

B-pronggroundedpl

Gas supply requirements

; EXPLOSION HAZARD

Uncoated copper tubing will corrode when subjected

to natural gas, causing gas leaks. Use ONLYblack iron,

stainless steel, or plastic-coated brass piping for gas

supply.

1 Installation MUST conform with local codes, or in

the absence of local codes, with the National Fuel

Gas Code, ANSI Z223.I (latest edition).

2 The gas supply line should be 1/2 inch (1.27 cm)

pipe.

3 If codes allow, flexible metal tubing may be used

to connect your dryer to the gas supply line. The

tubing MUSTbe constructed of stainless steel or

plastic-coated brass.

4. The gas supply line MUSThave an individual

shutoff valve installed in accordance with the

B!49.!, Natural Gasand Propane Installation Code.

5 A !/8 inch (0.32 cm) N.P.T.plugged tapping,

accessible for test gauge connection, MUST be

installed immediately upstream of the gas supply

connection to the dryer.

6 The dryer MUSTbe disconnected from the gas

supply piping system during any pressure testing

of the gas supply piping system at test pressures in

excess of !/2 psig (3.45 kPa).

7 The dryer MUSTbe isolated from the gas supply

piping system during any pressure testing of the

gas supply piping system at test pressures equal to

or tessthan Z/2 psig (3.45 kPa).

8 Connections for the gas supply must comply with

the Standard for Connectors for GasAppliances,

ANSI Z21.24.

Exhaust system requirements

Use only 4 inch (i02 mm) diameter (minimum) rigid

or flexible metal duct and approved vent hood which

has a swing-out damper(s) that open when the dryer

is in operation. When the dryer stops, the dampers

automatically close to prevent drafts and the entrance

of insects and rodents. To avoid restricting the outlet,

maintain a minimum of !2 inches (30.5 cm) clearance

between the vent hood and the ground or any other

obstruction.

FIRE HAZARD

Failure to follow these instructions can create excessive

drying times and fire hazards.

The following are specific requirements for proper

and safe operation of your dryer,

FIRE HAZARD

Do not install a clothes dryer with flexible plastic or

metal foil venting materials. Flexible venting materials

are known to collapse, be easily crushed and trap tint.

These conditions witt obstruct clothes dryer airflow and

increase the risk of fire.

If your present system is made up of plastic duct or

metal foil duct, replace it with a rigid or semi-rigid metal

duct. Also, ensure the present duct is free of any lint prior

to installing dryer duct.

li;;:_:_;:;_!!:_iiiii; ;_i¸__;i;_¸i¸!_;;_i_ii ;_11 iiii

Correct

[_; ¸i¸i¸i¸i¸i¸i¸i¸i¸i¸i¸i¸i¸i¸i¸i¸i

Incorrect

L

Exhaust system requirements, continued

FIRE HAZARD FIRE HAZARD

A clothes dryer must be exhausted outdoors• Do not Exceeding the length of duct pipe or number of elbows

exhaust dryer into a chimney, a wall, a ceiling, an attic, allowed in the "MAXIMUM LENGTH" charts can cause

a crawl space or any concealed space of a building• A an accumulation of lint in the exhaust system• Plugging

clothes dryer produces combustible lint. If the dryer is

not exhausted outdoors, some fine lint will be expelled

into the laundry area• An accumulation of tint in any

area of the home can create a health and fire hazard.

The dryer must be connected to an exhaust outdoors.

Regularly inspect the outdoor exhaust opening and

remove any accumulation of lint around the outdoor

exhaust opening and in the surrounding area.

FIRE HAZARD

Do not allow combustible materials (for example:

clothing, draperies/curtains, paper) to come in

contact with exhaust system. The dryer MUST NOT

be exhausted into a chimney, a wall, a ceiling,

or any concealed space of a building which can

accumulate lint, resulting in a fire hazard.

Do not screen the exhaust ends of the vent system,

or use any screws, rivets or other fasteners that

extend into the duct to assemble the exhaust

system. Lint can become caught in the screen, on

the system could create a fire hazard, as welt as

increase drying times.

MAXIMUM LENGTH

of 4" (102mm) Rigid Metal Duct

9 VENT HOOD TYPE

(Preferred)

4" 2.5"

(102ram) Iouvered (6.35cm)

0 64 ft. (19.5 m) 48 ft. (14.6 m)

1 52 ft. (15,9 m) 40 ft, (12.2 m)

2 44 ft. (13,5 m) 32 ft, (9.8 m)

3 36 ft. (11 m) 24 ft. (7.3 m)

4 28 ft. (9,5 m) 16 ft, (4.9 m)

o Do not install flexible plastic or flexible foil venting

the screws or rivets, clogging the duct work and material.

creating a fire hazard as welt as increasing drying

..... * If nsta ngsem-rgdventng do not exceed8ft

t mes Use an approved vent hood to term nate the "2 4 m" duct len th

• _. ) g •

duct outdoors, and seal all ]omts wtth metal fotl duct .....

tape, All male duct pipe fittings MUST be instalied

downstream with the flow of air.

Exhaust system requirements, continued

Install male fittings in correct direction:

CORRECT INCORRECT

In installations where the exhaust system is not described

in the charts, the following method must be used to

determine if the exhaust system is acceptable:

:1. Connect an inclined or digital manometer between

the dryer and the point the exhaust connects to the

dryer.

2 Set the dryer timer and temperature to Air Dry and

start the dryer.

3 Read the measurement on the manometer.

4 The system back pressure MUST NOT be higher

than 0.75 inches of water column. If the

system back pressure is tess than 0.75 inches of

water column, the system is acceptable. If the

manometer reading is higher than 0.75 inches of

water column, the system is too restrictive and the

installation is unacceptable.

Although vertical orientation of the exhaust system is

acceptable, certain extenuating circumstances could

affect the performance of the dryer:

• Only rigid metal duct work should be used.

• Venting vertically through a roof may expose the

exhaust system to down drafts causing an increase

in vent restriction.

• Running the exhaust system through an

uninsulated area may cause condensation and

faster accumulation of lint.

• Compression or crimping of the exhaust system will

cause an increase in vent restriction.

• The exhaust system should be inspected and

cleaned a minimum of every 18 months with

normal usage. The more the dryer is used, the

more often you should check the exhaust system

and vent hood for proper operation.

Exhaust direction

Directional exhausting can be accomplished by installing

a quick-turn 90 ° dryer vent elbow directly to exhaust

outlet of dryer. Dryer vent elbows are available through

your local parts distributor or hardware store.

See also Clearance Requirements on the next page.

Use of 90 ° quick-turn

elbow is required to meet

minimum installation

depth of free-standing

dryer.

Manufactured or mobile home installation

1 Installation MUST conform to current Manufactured

Home Construction & Safety Standard, Title 24

CFR, Part 32-80 (formerly the Federal Standard

for Mobile Home Construction and Safety, Title 24,

HUD Part 280) or Standard CAN/CSAZ240 MH.

2 Dryer MUST be exhausted outside (outdoors, not

beneath the mobile home) using metal ducting

that wilt not support combustion. Metal ducting

must be 4 inches (i0.i6 cm) in diameter with no

obstructions. Rigid metal duct is preferred.

3 If dryer is exhausted through the floor and area

beneath the mobile home is enclosed, the exhaust

system MUST terminate outside the enclosure with

the termination securely fastened to the mobile

home structure.

4 Refer to previous sections in this guide for other

important exhaust venting system requirements.

5 When installing a gas dryer into a mobile home, a

provision must be made for outside make up air.

This provision is to be not less than twice the area

of the dryer exhaust outlet.

6 Installer MUST anchor this dryer to the floor

with approved Mobile Home Installation Kit - P/N

137087200.

Installation in a Recess or Closet

1 A dryer installed in a bedroom, bathroom, recess or

closet, MUST be exhausted outdoors.

2 No other fuel burning appliance shall be installed in

the same closet as the gas dryer.

3 Your dryer needs the space around it for proper

ventilation.

DO NOT install your dryer in a closet with a solid door.

4 Closet door ventilation required: A minimum

of !20 square inches (774.2 cm 2) of opening,

equally divided at the top and bottom of the

door, is required. Openings should be located 3

inches (7.6 cm) from bottom and top of door.

Openings are required to be unobstructed when a

door is installed. A Iouvered door with equivalent

air openings for the full length of the door is

acceptable,

closet door

Clearance requirements

INSTALLYOUR DRYER:

I In anareaexposedtodrippingwateroroutside

weatherconditions.

2 In anareawhere itwillcome incontactwith

curtains,drapes,oranythingthatwillobstruct

theflowofcombustionand ventilationair.

3 On carpet.FloorMUST be solidwitha maximum

slope of i inch (2.54 cm).

EXPLOSION HAZARD

Do not install the dryer where gasoline or other

flammables are kept or stored. If the dryer is installed

in a garage, it must be a minimum of !8 inches (45.7

cm) above the floor. Failure to do so can result in

death, explosion, fire or burns.

MINIMUM INSTALLATION CLEARANCES - Inches (cm)

SIDES REAR TOP FRONT

Alcove 0" (0 cm) 0" (O cm)* 23" (58.5 cm) n/a

Closet 0"(0 crn) 0" (0 cm) _ 23" (58.5 crn) 1" (2.5 crn)

* Dryer must be vented straight back to achieve

0" (0 cm) rear installation.

(oO#i_) o"

(0cm)

1" "

(2.5 cm) (00cm)

_ii_ -iL

To achieve an installation with 0" (0 cm) clearance

for the back of the dryer (for other than straight back

venting), a quick-turn 90 ° dryer vent elbow must be

installed as described previously in this manual,

Dryer Dimensions

I_ 27' (68,5 cm)

38,5"

(98 cm)

42,5"

(108 cm)

electrical

supply on

rear of unitI

gas supply _

pipe on rear

of gas unit

(34,5 cm)

to center of rear vent

:enterline height

3.7"

(9,5 cm) floorline

S0" (127cm) _lJ

to

I_ 29" (73,5 cm)

to front of dosed door

iPowe, sul)ply cmd length on gas unit ap]3mxima_ely 6O in( he£ (1525 cm)

i!!i!i!l!_!0 ill

Electrical installation

The following are specific requirements for proper and

safe electrical installation of your dryer. Failure to follow

these instructions can create electrical shock and/or a

fire hazard.

ELECTRICAL SHOCK HAZARD

This appliance MUST be properly grounded.

Electrical shock can result if the dryer is not properly

grounded. Follow the instructions in this manual for

proper grounding.

o

• Do not use an extension cord with this dryer. Some

extension cords are not designed to withstand the

amounts of electrical current this dryer utilizes

and can melt, creating electrical shock and/

or fire hazard. Locate the dryer within reach of

the receptacle for the length power cord to be

purchased, allowing some slack in the cord. Refer to

the pre-installation requirements inthis manual for

the proper power cord to be purchased power supply.

ELECTRICAL SHOCK HAZARD

• A U.L.-approved strain relief must be installed onto

power cord. If the strain relief is not attached, the

cord can be pulled out of the dryer and can be cut

by any movement of the cord, resulting in electrical

shock.

Do not use an aluminum wired receptacle with a

copper wired power cord and plug (or vice versa).

A chemical reaction occurs between copper and

aluminum and can cause electrical shorts. The

proper wiring and receptacle is a copper wired

power cord with a copper wired receptacle.

Grounding requirements - Electric dryer (USA)

conductor can result in a risk of electrical shock. Check

with a licensed electrician if you are in doubt as to

whether the appliance is properly grounded.

For a grounded, cord-connected dryer:

1 The dryer MUSTbe grounded. In the event of a

malfunction or breakdown, grounding will reduce

the risk of electrical shock by a path of least

resistance for electrical current.

2 After you purchase and install a 3 wire or 4 wire

power supply cord having an equipment-grounding

conductor and a grounding plug that matches you

wiring system, the plug MUSTbe plugged into

an appropriate, copper wired receptacle that is

properly installed and grounded in accordance with

all local codes and ordinances. If in doubt, call a

licensed electrician.

3 DO NOT modify the plug you've installed on this

appliance. If it will not fit the outlet, have a proper

outlet installed by a qualified electrician.

For a permanently connected dryer:

1 The dryer MUST be connected to a grounded

metal, permanent wiring system; or an equipment

grounding conductor must be run with the circuit

conductors and connected to the equipment-

grounding terminal or lead on the appliance.

Grounding requirements - Electric dryer (Canada)

ELECTRICAL SHOCK HAZARD

Improper connection of the equipment grounding

conductor can result in a risk of electrical shock. Check

with a licensed electrician if you are in doubt as to

whether the appliance is properly grounded.

For a grounded, cord-connected dryer:

1 The dryer MUST be grounded. In the event of a

malfunction or breakdown, grounding will reduce the

risk of electrical shock by a path of least resistance

for electrical current.

2 Since your dryer is equipped with a power supply

cord having an equipment-grounding conductor and

a grounding plug, the plug must be plugged into

an appropriate outlet that is properly installed and

grounded in accordance with all local codes and

ordinances. If in doubt, call a licensed electrician.

3 DO NOT modify the plug provided with this

appliance. If it will not fit the outlet, have a proper

outlet installed by a qualified electrician.

Grounding requirements = Gas dryer (USA and Canada)

1 The dryer is equipped with a three-prong

(grounding) plug for your protection against shock

hazard and should be plugged directly into a

properly grounded three-prong receptacle.

2 The plug must be plugged into an appropriate

outlet that is properly installed and grounded in

accordance with all local codes and ordinances. If

in doubt, call a licensed electrician.

3 DO NOT modify the plug provided with this

appliance. If it will not fit the outlet, have a proper

outlet installed by a qualified electrician.

Grounding type

wail receptacle

f Do not. under

any circumstances

or bypass the

__ grounding prong.

Pc_er cord with

3-prong grounded plug

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_i_i_i_i!!!_i_iiii_!i! _ii _i!_i!i_!i!_iii_i_ii_i_illi_i_ii!i_ii_i_iii!_ii

Gas connection

:1. Remove the shipping cap from gas pipe at the rear

of the dryer.

DO NOT connect the dryer to L.P,gas service without

converting the gas valve. An L.P.conversion kit must

be installed by a qualified gas technician.

Connect a 1/2 inch (1.27 cm) I.D. semi-rigid or

approved pipe from gas supply line to the 3/8 inch

(0.96 cm) pipe located on the back of the dryer.

Use a 1/2 inch to 3/8 inch (1.27 cm to 0.96 cm)

reducer for the connection. Apply an approved

thread sealer that is resistant to the corrosive

action of liquefied gases on all pipe connections.

Manua GAS FLOW

Shutoff Flare _ Flare |

Valve Union Union |

l

,o_/:_ed71_Fi_'_i l_'_:::l_:_\_/_'i I I

: ,_tl t ' t t [

\. Nipple Flexible Inlet Pipe on |

Open Connector Back of Dryer |

All connectionsmustbe wrench-tightened J

3 Open the shutoff valve in the gas supply line to

allow gas to flow through the pipe. Wait a few

minutes for gas to move through the gas line.

Open position

4 Check for gas system leaks with a manometer. If a

manometer is not available, test all connections by

brushing on a soapy water solution,

The supply line must be equipped with an approved

manual shutoff valve. This valve should be located in

the same room as the dryer and should be in a location

that allows ease of opening and closing. Do not block

access to the gas shutoff valve.

Electrical connection (non=Canada) - 3 wire cord

3-wire receptacle

(NEMA type 10-30R)

ELECTR:CALS.OCK.AzARD

Failure to disconnect power source before servicing

could result in personal injury or even death.

:1. Turn off power supply to outlet.

2 Remove the screw securing the terminal block

access cover in the lower corner on the back of the

dryer.

3 Install a UL-approved strain relief according to the

power cord/strain relief manufacturer's instructions

in the power cord entry hole below the access

panel. At this time, the strain relief should be

loosely in place.

4 Thread an UNPLUGGED,UL-approved, 30 amp.

power cord, NEHA 10-30 type SRDT,through the

strain relief.

5 Attach the power cord neutral (center wire)

conductor to the SILVERcolored center terminal on

the terminal block, Tighten the screw securely.

6 Attach the remaining two power cord outer

conductors to the outer, BRASScolored terminals

on the terminal block, Tighten both screws

securely,

(SILVER terminal)

Line 1

(BRASS terminal)

_ Internal ground

(GREEN screw)

recoveryslot

If a terminal screw falls during cord installation, it can

Do not make a sharp bend or crimp wiring/conductor

at connections.

7 Follow manufacturer's guidelines for firmly securing

the strain relief and power cord.

8 Reinstall the terminal block cover.

DO NOT remove

Neutral

internal ground in terminal

a 3-wire system]!

:If moving dryer from a 4-wire system and installing it

in a 3-wire system, move the internal ground from the

center terminal back to the GREENscrew next to the

terminal block.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_i_i_i_i!!!_i_iiii_!i! _ii _i!_i!i_!i!_iii_i_ii_i_illi_i_ii!i_ii_i_iii!_ii

Electrical connection (non=Canada) = 4 wire cord

4-wire receptacle

(NEMA type 14-30R)

3. Turn off power supply to outlet.

2 Remove the screw securing the terminal block

access cover in the lower corner on the back of the

dryer.

3 Install a UL-approved strain retief according to the

power cord/strain relief manufacturer's instructions

in the power cord entry hole below the access

paneh At this time, the strain relief should be

loosely in place.

4 Thread an UNPLUGGED,UL-approved, 30 amp.

power cord, NEHA 14-30 type ST or SRDT,through

the strain relief.

5 Disconnect the internal (WHITE) dryer harness

ground wire from the (GREEN) ground screw next

to the terminal block.

6 Attach the ground (GREEN) power cord wire to the

cabinet with the ground (GREEN) screw. Tighten

the screw securely.

7 Nave the internal dryer harness ground (WHITE)

wire to the terminal block and attach it along with

the neutral (WHITE) power cord wire conductor

to the center, SILVERcolored terminal on the

terminal block. Tighten the screw securely.

8 Attach the RED and BLACKpower cord conductors

to the outer, BRASScolored terminals on the

terminal block. Tighten both screws securely.

ELEC'r.'CALS,oCK"AZAP,D

Donotmakeasbarpbendorcrimpwirhg/conductor

at connections.

9 Follow manufacturer's guidelines for firmly securing

the strain relief and power cord.

3.0 Reinstall the terminal block cover.

__ Acc_ cover

f_ black

Line 2

(BRASS terminal)

Neutral

(SILVER terminal)

Line 1

(BRASS terminal)

-_ Internal ground

(GREEN screw)

Install

UL-approved

strain relief here

Terminal screw

recovery slot

Ifa terminal screw falls during cord installation, it can

be retrieved in the terminal screw recovery slot below

the access panel. ...............

Move internal ground (WHITE)

wire to neutral (SILVER)

terminal for 4-wRe s

{

GREEN

ground screw

\

Neutral

terminal

neutral wire

GREEN

ground wit

BLACK

power wire

RED power wir

General installation

1 Connect the exhaust duct to the outside exhaust

system, Use of a 4" (102 mm) clamp (item A) is

recommended to connect the dryer to the exhaust

vent system, Use metal foit tape to seal all other

joints,

2 Use a carpenter's level to level your dryer front-to-

back and side-to-side,

3 Use adjustable pliers to adjust the leveling legs so

the dryer is level front-to-rear and side-to-side, and

stable comer-to-corner,

4 Press down on alternate corners and sides and feel

for the slightest movement. Adjust the appropriate

leg(s) so the dryer sits solidly on the floor on ALL

four tegs, Keep the leveling leg extension at a

minimum for best performance of the dryer.

5 Plugthe power cord into a grounded outlet.

..... I1receptacle

any circumstances,

_._ti,tea nce s' Icut ........

grounding prong.j_

Power cord with

3:prong grounded plug

6 Turn on the power at the circuit breaker/fuse box.

7 Read the Use & Care Guide provided with the dryer.

It contains valuable and helpful information that

wilt save you time and money.

8 If you have any questions during initial operation,

please review the "Avoid Service Checklist" in your

Use & Care Guide before calling for service.

9 Placethese instructions in a location near the dryer

for future reference.

Yourdryerisdesignedsothedoorswingmaybereversedatanytimewithoutadditionalparts.Conversionis

accomplishedbytransferringhingesanddoorstriketotheoppositesidesofthecabinet.

I Be sure you have adequate swing area Tools needed:

before reversing door. _ _ %_,

2 You will need a screw driver with a #2 square ELECTRICAL SHOCK HAZARD _, ( \,_ } "*_, :i_

: bit and a pair of pliers. Failure to disconnect power source _,t,, _' ">- X_!_

3 Protect flat work surface such as top of dryer before servicing could result in

or floor near dryer, with a soft cloth or towel, personal injury or even death. Screwdriverwith #2 Adjustable

4 Be sure dryer is unplugged from power source! ......................................................................................................................................................squarebit pliers

! Open door and remove four plugs in the door opening 3 Place door on a towel (front side down) to prevent

opposite the hinges. Retain all parts for use later, scratches to paint or window (if equipped). Remove

unless otherwise noted. (Figure below) all four remaining long hinge screws on edge of door.

Be careful not to scratch the paint.

Observe the "D" stamped on the interior of the hinge

on the door side. When reversed to the other side, this

f--_2: HOLE PLUGS(x4) "D" must be visible after the hinge is remounted.

HINGE SCREW_

"D" STAMPEDON

DOOR SIDE OF

HINGE INTERIOR

2 Begin removing the four short screws that attach the

hinge to the front panel. (Figure Above) Start by only

removing one screw per hinge. Then only loosen the

two remaining screws while firmly holding the door to

prevent damage to hinge, front panel or door. After the

remaining screws are loosened, continue to remove all.

DOOR EDGE

SCREWS(x 4)

DOOR

SCREWS (x 4)

4 Remove the four long screws from edge of door

opposite hinges. (Figure above)

5 Installfourlongscrewssecuringhingetodoor

assemblyinthenewlocation,takenotetoplace

eachhingeincorrectorientation.(Figurebelow)

Theplatewiththestamped"D"ismountedtothedoor.

The"D"mustbevisibleafterthehingeisremounted

andthespineofthehingeshouldbeorientedtoward

thefrontsideofthedoorforcorrectoperation............

DOOREDGE

SCREWS(x4',

"D"STAMPEDONDOOR

SIDEOFHINGEINTERIOR

DOOR HINGE

SCREWS (x 4)

6 Install four long screws into holes that had secured

the hinges. (Figure above)

7 Remove striker and discard. (Figure below)

8 Remove square plug opposite striker. (Figure above)

If plug is damaged during removal, discard and install

new plug (included in literature bag) into hole striker

was just removed from.

9 Install new striker (included in literature bag) into hole

square plug was previously installed in. (Figure below)

i0 Grasping firmly the top of the door, position the door

near the door opening and align the top hinge hole

to the top hole in the front panel door opening. Once

the first short screw is started, attach the second

short screw to the lower hinge. Once both screws

are tightened, install the remaining two short screws.

(Figure below)

HOLE PLUGS(x

ON

DOOR SIDE OF

HINGE INTERIOR

i! Install four plugs into the front panel door opening

where hinges were originally installed. (Figure above)

i2 Close the door and test operation of hinge, strike and

latch.

LP CONVERSION KIT

P/N PCK4200

Gas dryers intended for use in a location supplied with LP

must use a conversion kit prior to installation.

MOBILE HOME INSTALLATION KIT

P/N137067200

Installation in a mobile home requires the use of a

MOBILE HOMEINSTALLATION KIT.

DRYING RACK (FOR USE WITH HODELS EQUIPPED

WITH MOISTURE SENSING BARS)

P/N137067300

Depending on the model you purchased, a drying rack

may have been included in the initial purchase of your

dryer. If your model did not include a drying rack or you

desire another drying rack, you may order one,

UNIVERSAL APPLIANCE WRENCH

P/N137019200

A UNIVERSALAPPLIANCE WRENCHis available to aid in

dryer/washer/pedestal feet adjustment,

TOUCH UP PAINT PENS*

Classic White Touch Up Pen - P/N 5304468812

_Other colors may be available. Contact the source where you

purchased your dryer.

approved by) the manufacturer could result in personal

Technical Sheet/Wiring Diagram:

A wiring diagram and technical data sheet are located

inside the dryer console.

To remove the console faceplate follow the directions

below:

1. Disconnect dryer from electrical source.

2. Remove the two screws toward the top on the back of

the console housing.

3. Insert a small screw driver through each hole on the

back of the console housing and gently press inward

to disengage each upper faceplate retaining tab.

4. Gently lay the console faceplate forward to access

technical/wiring diagram.

5. When finished with repair, return sheet inside console,

ensure lower retaining tabs are in place and snap

faceplate to upper retaining tabs. Reinsert the two

screws removed earlier.

TECH DATA SHEET/

Replacement parts:

Ifreplacementspartsareneeded foryourdryer,contact

the source where you purchased your dryer or refer to

your Use and Care Guide for more information. ELECTRICAL SHOCK HAZARD

Label all wires prior to disconnection when servicing

controls. Wiring errors can cause improper and dangerous

operation. Verify proper operation after servicing.

La page charge ...

Frigidaire FFRE1001PW0 Guide d'installation

Ce manuel convient également à

Frigidaire FFRE1001PW0 Guide d'installation

dans d''autres langues

Autres documents