Tascam IF-AE8 Manuel utilisateur

Marque: Tascam

Modèle: IF-AE8

Catégorie: Convertisseurs audio

Taper: Manuel utilisateur

IF-AE8

Digital Audio Interface Unit

OWNER’S MANUAL

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The exclamation point within an equilateral triangle is intended to alert the user to the pres-

ence of important operating and maintenance (servicing) instructions in the literature

accompanying the appliance.

The lightning ﬂash with arrowhead symbol, within an equilateral triangle, is intended to alert

the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure

that may be of sufﬁcient magnitude to constitute a risk of electric shock to persons..

This appliance has a serial number

located on the rear panel. Please record

the model number and serial number

and retain them for your records.

Model number

Serial number

WARNING: TO PREVENT FIRE OR SHOCK

HAZARD, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

D00446000A

TASCAM IF-AE8

Important Safety Precautions

IMPORTANT (for U.K. Customers)

DO NOT cut off the mains plug from this equipment.

If the plug ﬁtted is not suitable for the power points in your

home or the cable is too short to reach a power point, then

obtain an appropriate safety approved extension lead or

consult your dealer.

If nonetheless the mains plug is cut off, remove the fuse and

dispose of the plug immediately, to avoid a possible shock

hazard by inadvertent connection to the mains supply.

If this product is not provided with a mains plug, or one has

to be ﬁtted, then follow the instructions given below:

IMPORTANT. DO NOT

make any connection to the larger

terminal which is marked with the letter E or by the safety

earth symbol

or coloured GREEN or GREEN-and-

YELLOW.

The wires in the mains lead on this product are coloured in

accordance with the following code:

BLUE: NEUTRAL

BROWN: LIVE

As these colours may not correspond with the coloured

markings identifying the terminals in your plug proceed as

follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured

BLACK.

The wire which is coloured BROWN must be connected to

the terminal which is marked with the letter L or coloured

RED.

When replacing the fuse only a correctly rated appro

ved

type should be used and be sure to re-ﬁt the fuse cover.

IF IN DOUBT — CONSULT A COMPETENT

ELECTRICIAN.

TO THE USER

This equipment has been tested and found to

comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable

protection against harmful interference when the

equipment is operated in a commercial

environment. This equipment generates, uses,

and can radiate radio frequency energy and, if

not installed and used in accordance with the

instruction manual, may cause harmful

interference to radio communications.

Operation of this equipment in a residental area

is likely to cause harmful interference in which

case the user will be required to correct the

interference at his own expense.

CAUTION

Changes or modifications to this equipment not

expressly approved by TEAC CORPORATION

for compliance could void the user’s authority to

operate this equipment.

For the consumers in Europe

WARNING

This is a Class A product. In a domestic environment, this

product may cause radio interference in which case the user

may be required to take adequate measures.

Pour les utilisateurs en Europe

AVERTISSEMENT

Il s’agit d’un produit de Classe A. Dans un environnement

domestique, cet appareil peut provoquer des interférences

radio, dans ce cas l’utilisateur peut être amené à prendre

des mesures appropriées.

Für Kunden in Europa

Warnung

Dies is eine Einrichtung, welche die Funk-Entstörung nach

Klasse A besitzt. Diese Einrichtung kann im Wohnbereich

Funkstörungen versursachen ; in diesem Fall kann vom

Betrieber verlang werden, angemessene Maßnahmen

durchzuführen und dafür aufzukommen.

For U.S.A

TASCAM IF-AE8

CAUTION:

…

Read all of these Instructions.

…

Save these Instructions for later use.

…

Follow all Warnings and Instructions marked on the audio

equipment.

1) Read Instructions

— All the safety and operating instructions should

be read before the product is operated.

2) Retain Instructions

— The safety and operating instructions should

be retained for future reference.

3) Heed Warnings

— All warnings on the product and in the operating

instructions should be adhered to.

4) Follow Instructions

— All operating and use instructions should be

followed.

5) Cleaning

— Unplug this product from the wall outlet before cleaning.

Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for clean-

ing.

6) Attachments

— Do not use attachments not recommended by the

product manufacturer as they may cause hazards.

7) Water and Moisture

— Do not use this product near water — for

example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet

basement; or near a swimming pool; and the like.

8) Accessories

— Do not place this product on an unstable cart, stand,

tripod, bracket, or table. The product may fall, causing serious injury to a

child or adult, and serious damage to the product. Use only with a cart,

stand, tripod, bracket, or table recommended by the manufacturer, or sold

with the product. Any mounting of the product should follow the manufac-

turer’s instructions, and should use a mounting accessory recommended by

the manufacturer.

A product and cart combination should be moved with care. Quick stops,

excessive force, and uneven surfaces may cause the product and cart com-

bination to overturn.

10)

Ventilation

— Slots and openings in the cabinet are provided for ven-

tilation and to ensure reliable operation of the product and to protect it

from overheating, and these openings must not be blocked or covered. The

openings should never be blocked by placing the product on a bed, sofa,

rug, or other similar surface. This product should not be placed in a built-in

installation such as a bookcase or rack unless proper ventilation is provided

or the manufacturer’s instructions have been adhered to.

11) Power Sources

— This product should be operated only from the

type of power source indicated on the marking label. If you are not sure of

the type of power supply to your home, consult your product dealer or local

power company. For products intended to operate from battery power, or

other sources, refer to the operating instructions.

12) Grounding or Polarization

— This product may be equipped with a

polarized alternating-current line plug (a plug having one blade wider than

the other). This plug will fit into the power outlet only one way. This is a

safety feature. If you are unable to insert the plug fully into the outlet, try

reversing the plug. If the plug should still fail to fit, contact your electrician

to replace your obsolete outlet. Do not defeat the safety purpose of the

polarized plug.

13) Power-Cord Protection

— Power-supply cords should be routed so

that they are not likely to be walked on or pinched by items placed upon or

against them, paying particular attention to cords at plugs, convenience

receptacles, and the point where they exit from the product.

14) Outdoor Antenna Grounding

— If an outside antenna or cable

system is connected to the product, be sure the antenna or cable system is

grounded so as to provide some protection against voltage surges and built-

up static charges. Article 810 of the National Electrical Code, ANSI/NFPA

70, provides information with regard to proper grounding of the mast and

supporting structure, grounding of the lead-in wire to an antenna discharge

unit, size of grounding conductors, location of antenna-discharge unit, con-

nection to grounding electrodes, and requirements for the grounding elec-

trode.

"Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to

Section 820-40 of the NEC which provides guidelines for proper grounding

and, in particular, specifies that the cable ground shall be connected to the

grounding system of the building, as close to the point of cable entry as

practical.

15) Lightning

— For added protection for this product during a lightning

storm, or when it is left unattended and unused for long periods of time,

unplug it from the wall outlet and disconnect the antenna or cable system.

This will prevent damage to the product due to lightning and power-line

surges.

16) Power Lines

— An outside antenna system should not be located in

the vicinity of overhead power lines or other electric light or power circuits,

or where it can fall into such power lines or circuits. When installing an

outside antenna system, extreme care should be taken to keep from touch-

ing such power lines or circuits as contact with them might be fatal.

17) Overloading

— Do not overload wall outlets, extension cords, or

integral convenience receptacles as this can result in risk of fire or electric

shock.

18) Object and Liquid Entry

— Never push objects of any kind into

this product through openings as they may touch dangerous voltage points

or short-out parts that could result in a fire or electric shock. Never spill

liquid of any kind on the product.

19) Servicing

— Do not attempt to service this product yourself as open-

ing or removing covers may expose you to dangerous voltage or other

hazards. Refer all servicing to qualified service personnel.

20) Damage Requiring Service

— Unplug this product from the wall

outlet and refer servicing to qualified service personnel under the following

conditions:

when the power-supply cord or plug is damaged.

if liquid has been spilled, or objects have fallen into the product.

if the product has been exposed to rain or water.

if the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the operating

instructions as an improper adjustment of other controls may result in

damage and will often require extensive work by a qualified technician to

restore the product to its normal operation.

if the product has been dropped or damaged in any way.

f )

when the product exhibits a distinct change in performance – this

indicates a need for service.

21) Replacement Parts

— When replacement parts are required, be

sure the service technician has used replacement parts specified by the

manufacturer or have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock, or other

hazards.

22) Safety Check

— Upon completion of any service or repairs to this

product, ask the service technician to perform safety checks to determine

that the product is in proper operating condition.

23) Wall or Ceiling Mounting

— The product should be mounted to a

wall or ceiling only as recommended by the manufacturer.

24) Heat

— The product should be situated away from heat sources such

as radiators, heat registers, stoves, or other products (including amplifiers)

that produce heat.

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

NEC - NATIONAL ELECTRICAL CODE

ELECTRIC

SERVICE

EQUIPMENT

Example of Antenna Grounding as per

National Electrical Code, ANSI/NFPA 70

GROUND

CLAMP

IMPORTANT SAFETY INSTRUCTIONS

TASCAM IF-AE8

IF-AE8 Digital Audio Converter

The TASCAM IF-AE8 provides a convenient way of

exchanging digital audio data between

TDIF-1-equipped devices, such as DTRS recorders,

and AES/EBU devices.

A single TDIF-1 connector carries eight channels of

digital input and output. Four XLR-type connectors

accept four two-channel input signals in AES3-1992

format, and another four XLR-type connectors out-

put four two-channel input signals in AES3-1992

format.

The word synchronization is selectable, using a front

panel switch, from any of the four

AES/EBU

inputs,

from the TDIF-1 source, or from an external inde-

pendent word clock source.

The word clock source can be used as the clock

source for sampling frequency conversion. All stan-

dard rates (32 kHz, 44.1 kHz and 48 kHz) are sup-

ported for input and output.

If sampling frequency conversion is carried out, the

IF-AE8 will generate an independent clock signal,

based on the target frequency, so that other units may

be synchronized to it.

The signal transmitted from the

AES/EBU

outputs

can be selected to come from the

AES/EBU

input

signals or from those received at the TDIF-1 connec-

tor, using a front panel switch.

Format conversion is possible with up to 24-bit data

with TDIF digital audio format, and 20-bit with

AES3-1992 format data if no sample rate conversion

is performed (20-bit data for both formats if the sam-

pling frequency is converted).

The digital audio output format is selectable as either

professional or consumer format using a front panel

switch.

1 Front panel

POWER switch and indicator

Push the

POWER

switch once to turn on power, and

again to turn it off. The

POWER

indicator lights

when power is supplied to the IF-AE8.

LOCKED indicator

When a valid clock signal is received at the selected

clock source, this indicator will light.

CLOCK switch and indicators

This switch allows you to cycle between the six pos-

sible clock sources for the IF-AE8: the

WORD

SYNC IN

connector, the

DIGITAL I/O (TDIF-1)

connector, or any of the four two-channel

AES/EBU connectors (

DIGITAL I/O (AES/EBU)

INPUTS (1/2, 3/4, 5/6, 7/8)

), as shown by the

indicators to the right of the switch.

WARNING

There should usually never be more than one

word clock signal in a digital audio system. If

there are not, at worst, damage may occur to

speakers, ampliﬁers, etc. as a result of

high-frequency noise generated by word clock

incompatibilities.

DIGITAL OUT switch and indicators

This switch allows you to select the source of the

digital audio signals that are output from the

DIGITAL I/O (AES/EBU) OUTPUTS (1/2, 3/4,

5/6, 7/8)

. The source can either be the signals

received at the

AES/EBU

inputs

(

DIGITAL IN

)

or at the

TDIF-1

connector

If the

TDIF-1

option is selected, the eight channels of

the TDIF-1 audio are mapped on a “one-to-one”

basis to the eight

AES/EBU

audio output channels.

If the

DIGITAL IN

option is selected, the input data

received at the

AES/EBU

ports is passed through to

the corresponding output ports. However, it may be

passed through the sample rate conversion before

reaching the output ports.

DIGITAL OUT FORMAT switch and

indicators

The format of the digital audio output from the

AES/EBU

output connectors

may be either pro-

fessional AES3-1992 format (

PRO

) or

IF-AE8 Digital Audio Converter

TASCAM IF-AE8

CONSUMER

IEC-60958 TYPE II format. The elec-

trical characteristics of the output connectors remain

the same, regardless of the data format selected.

Fs RATE CONVERT switch and

indicators

This switch provides two settings:

THRU-1

and

CONVERT

When the switch is set to

THRU-1

, the input signals

(selected using the

DIGITAL OUT

switch) will be

output from the

AES/EBU

output connectors at the

same frequency.

When the switch is set to

CONVERT

, the input sig-

nals will be output at the sampling frequency of the

clock source selected with the

CLOCK

switch

Note that any of the

DIGITAL I/O (AES/EBU)

INPUTS (1/2, 3/4, 5/6, 7/8)

may be selected as

the clock source for the converted signal. The

DIGITAL I/O (TDIF-1)

cannot be used as the

clock source for conversion, though both it and the

DIGITAL I/O (AES/EBU) OUTPUTS (1/2, 3/4,

5/6, 7/8)

can be the destination.

NOTE

The

AES/EBU

unit which provides this clock

source may be different from the unit which

provides either the input or the output signals.

You must, however, make sure that word

clock synchronization is correctly carried out.

2 Rear panel

DIGITAL I/O (AES/EBU) OUTPUTS

(1/2, 3/4, 5/6, 7/8)

These balanced connectors output digital audio data

in AES3-1992 professional or in consumer format,

depending on the selection made with the

DIGITAL

OUT FORMAT

switch

The content of the data depends on the setting of the

DIGITAL OUT

switch

The sampling frequency of the output data depends

on the setting of the

Fs RATE CONVERT

switch

, and the currently-selected clock source

DIGITAL I/O (AES/EBU) INPUTS (1/2,

3/4, 5/6, 7/8)

These balanced connectors accept digital audio data

in AES3-1992 format.

The signal received at any of these connectors may

be selected as the clock source for the IF-AE8 using

the

CLOCK

switch

DIGITAL I/O (TDIF-1)

Use this connector to connect a suitably-equipped

TDIF-1 digital audio unit (e.g. a DTRS recorder or a

TASCAM digital mixing console).

The signals received at this connector may be

selected as the word clock source using the

CLOCK

switch

WARNING

Note that you should always use genuine

TASCAM cables, or cables which have been

approved for use with TDIF-1 interfaces by

TASCAM.

Although these cables appear similar to cer-

tain types of computer cables and use similar

connectors, the cables themselves are very

different, and the different electrical character-

istics of the cables can cause damage to the

equipment connected with the wrong cables.

If the use of cables other than TASCAM

cables causes or results in damage, the war-

ranty is voided.

WORD SYNC IN

The BNC connector accepts a word clock signal

from an external source.

It may be selected as the word clock source for the

IF-AE8 using the

CLOCK

switch

IF-AE8 Digital Audio Converter

TASCAM IF-AE8

B WORD SYNC OUT

This BNC connector outputs a word clock based on

the word clock source selected using the CLOCK

switch 3.

NOTE

This may or may not be the same as the clock

received at WORD SYNC IN A and retrans-

mitted through WORD SYNC THRU

. How-

ever, it is always the word clock selected

using the CLOCK switch

C WORD SYNC THRU

This BNC connector echoes the word clock signal

received at WORD SYNC IN A. It may or may not

be the same signal as is output at WORD SYNC

OUT B. It is auto-terminating.

3 Application example

In this example, the original material (from two

sources) has been mixed to DAT, and has been pro-

duced in both professional and consumer formats,

and at both 44.1 kHz and 48 kHz sample rates.

The ﬁnal master data will be recorded and coded on a

computer-based system, with an AES/EBU interface.

Here, the two DAT recorders are fed through the

IF-AE8. Since the resulting data will be at 44.1 kHz,

the DAT playing back the material at 44.1 kHz

(DAT 1) is selected to act as the clock master.

Since the TDIF-1 I/O is not used here, the DIGITAL

OUT switch 4 is set to DIGITAL IN.

The word clock is therefore derived from this, and

used to resample the 48 kHz material from DAT 2,

and the Fs RATE CONVERT switch 6 is set to

CONVERT.

The mastering system takes its word clock through

the AES/EBU data from the appropriate DIGITAL

OUT of the IF-AE8.

The DIGITAL OUT FORMAT switch 5 is set to

PRO, so that the data coming from DAT 2 is con-

verted to professional format data.

4 Specifications

IF-AE8

DAT 1

DAT 2

AES/EBU audio in

Mastering

system

44.1 (P)*

48 (C)

44.1(P)

DIGITAL OUTPUTs (1–2,

3–4, 5–6, 7–8)

XLR-type, balanced outputs

DIGITAL OUTPUT output

format

Switchable between

professional (AES3-1992)

and consumer (IEC-60958

TYPE II) formats

DIGITAL INPUTS (1–2, 3–4,

5–6, 7–8)

XLR-type

DIGITAL INPUT input format Auto-detect professional

(AES3-1992) and consumer

(IEC-60958 TYPE II) formats

D IGITAL I/O (TDIF-1) Conforms to TDIF-1

speciﬁcation

Clock source Any of AES/EBU DIGITAL

INPUTS, TDIF-1, or WORD

SYNC IN (front panel

selection)

LOCKED indicator Lights when valid clock

source received at selected

input

Valid input Fs rates 48 kHz, 44.1 kHz, 32 kHz

Valid output rates 48 kHz, 44.1 kHz, 32 kHz,

taken from CLOCK source

Word length Up to 24 bits TDIF-1,(20 bits

with Fs conversion), 20 bits

AES3-1992

WORD SYNC IN

Ω

WORD SYNC OUT

Ω

, reproduces clock

selected from front panel

switch

WORD SYNC THRU

Ω

(auto terminating),

echoes clock at WORD

SYNC IN

Dimensions (w x h x d) 428 x 48 x 194.8 (mm)

16.9 x 1.9 x 7.7 (in.)

Weight 2.6 kg (5.7 lbs)

Power supply 120V (UL), 230V (Europe,

Australia)

Power consumption 6 W

Supplied accessories Rack mounting kit

IF-AE8 Digital Audio Converter

TASCAM IF-AE8

4.1 Dimensional drawing 4.2 Rack mounting

Use the supplied rack mounting kit to install the

IF-AE8 in a standard 19” rack, as shown below:

4.3 Block diagram

482mm

466mm

44mm

4mm

32mm

194.8mm

181.5mm 10.5mm

CLOCK

FSC

AD1892

THRU

Data In

Emph In

Data Out

Emph Out

LR CLK In

LR CLK Out

Digital Mixer

DTRS

FS Code In

FS Code Out

THRU

(AUTO TERM)

WORD

PLL

LOCKED

TC9271

D OUT

D IN

TDIF

Fs CONVERT

CONVERT

THRU

Data

Fs / Emph

CLK

D IN 7-8

D IN 5-6

D IN 3-4

D IN 1-2

TDIF-1

WORD

OUT

DIGITAL I/O

INPUTS

(AES/EBU)

DIGITAL I/O

OUTPUTS

(AES/EBU)

1-2

3-4

5-6

7-8

1-2

3-4

5-6

7-8

TC9271

DIGITAL I/O

(TDIF-1)

FSC

AD1892

THRU

FSC

AD1892

THRU

FSC

AD1892

THRU

CPU

Digital

Interface

Receiver

Digital

Interface

Receiver

Digital

Interface

Receiver

Digital

Interface

Receiver

Digital

Interface

Transmitter

Digital

Interface

Transmitter

Fs / Emph

TEAC CORPORATION

Phone: (0422) 52-5082 3-7-3, Nakacho, Musashino-shi, Tokyo 180-8550, Japan

TEAC AMERICA, INC.

Phone: (323) 726-0303 7733 Telegraph Road, Montebello, California 90640

TEAC CANADA LTD.

Phone: 905-890-8008 Facsimile: 905-890-9888 5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada

TEAC MEXICO, S.A. De C.V

Phone: 5-658-1943 Privada De Corina, No.18, Colonia Del Carmen Coyoacon, Mexico DF 04100

TEAC UK LIMITED

Phone: 01923-819699 5 Marlin House, Marlins Meadow, The Croxley Centre, Watford, Herts. WD1 8YA, U.K.

TEAC DEUTSCHLAND GmbH

Phone: 0611-71580 Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany

TEAC FRANCE S. A.

Phone: 01.42.37.01.02 17 Rue Alexis-de-Tocqueville, CE 005 92182 Antony Cedex, France

TEAC BELGIUM NV/SA

Phone: 0031-30-6048115 P.A. TEAC Nederland BV, Perkinsbaan 11a, 3439 ND Nieuwegein, Netherlands

TEAC NEDERLAND BV

Phone: 030-6030229 Perkinsbaan 11a, 3439 ND Nieuwegein, Netherlands

TEAC AUSTRALIA PTY.,LTD. A.C.N. 005 408 462

Phone: (03) 9644-2442 106 Bay Street, Port Melbourne, Victoria 3207, Australia

TEAC ITALIANA S.p.A.

Phone: 02-66010500 Via C. Cantù 11, 20092 Cinisello Balsamo, Milano, Italy

PRINTED IN JAPAN 0199U0.7 M-1479A

IF-AE8

Tascam IF-AE8 Manuel utilisateur

Marque: Tascam

Modèle: IF-AE8

Catégorie: Convertisseurs audio

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Tascam IF-AE8 User manual

Tascam IF-AE8 Manuel utilisateur

Tascam IF-AE8 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents