Maytag Commercial MLG26PRKWW Guide d'installation

INSTALLATION

INSTRUCTIONS

Commercial Stacked Dryer

Gas (120-Volt, 60-Hz)

or Electric

(120/240-Volt, 60-Hz)

INSTRUCTIONS

D’INSTALLATION

Sécheuse à usage

commercial superposée

à gaz (120 Volts, 60 Hz)

ou électrique

(120/240 Volts, 60 Hz)

www.maytagcommerciallaundry.com

W10761033B

W10761034B-SP

TABLE OF CONTENTS

Page

Dryer Safety..........................................................................................................2

Tools & Parts ......................................................................................................5

Dimensions/Clearances ............................................................................. 6

Location Requirements ................................................................................ 7

Gas Dryer Electrical Requirements ....................................................... 8

Gas Requirements .......................................................................................... 9

Electric Dryer Electrical Requirements ............................................ 10

Dryer Venting Requirements .................................................................. 13

Gas Supply Connection ............................................................................ 15

Electric Dryer Electrical Connections ............................................... 17

Leveling .............................................................................................................. 21

Complete Installation .................................................................................. 22

Reversing Dryer Door Swing .................................................................. 23

Maintenance Instructions ......................................................................... 24

If You Need Assistance ............................................................................. 24

Electronic Control Setup Instructions ................................................ 25

Warranty ............................................................................................................ 30

TABLE DES MATIÈRES

Page

Sécurité de la sécheuse ............................................................................ 31

Outils et pièces ............................................................................................. 34

Dimensions/Distances de dégagement ......................................... 35

Exigences de l’emplacement .................................................................. 36

Exigences électriques pour la sécheuse à gaz ............................. 37

Exigences de gaz .......................................................................................... 38

Exigences électriques pour la sécheuse électrique ............... 39

Exigences concernant l’évacuation de la sécheuse ................. 40

Raccordement à la canalisation de gaz ............................................ 42

Nivellement .......................................................................................................44

Achever l’installation ....................................................................................45

Inversion du sens d’ouverture de la porte .......................................46

Instructions d’entretien ...............................................................................47

Si vous avez besoin d’assistance ......................................................... 47

Instructions de réglage du tableau

de commande électronique .....................................................................48

Garantie ............................................................................................................. 55

2

DRYER SAFETY

■ It is recommended that the owner post, in a prominent location, instructions for the customer’s use in the event the customer smells

gas. This information should be obtained from your gas supplier.

■ Post the following warning in a prominent location.

3

DRYER SAFETY

IMPORTANT: When discarding or storing your old clothes dryer, remove the door.

4

DRYER SAFETY

■ Clean dryer lint screen before or after each load.

■ Do not use this dryer without the lint screen in place.

■ Do not repair or replace any part of the dryer or attempt any

servicing unless speciﬁcally recommended in this Installation

Instructions or in published user-repair instructions that you

understand and have the skills to carry out.

■ Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

■ Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

■ The ﬁnal part of a tumble dryer cycle occurs without heat

(cool-down cycle) to ensure that the articles are left at a

temperature that ensures that the items will not be damaged.

■ WARNING: Never stop a tumble dryer before the end of

the drying cycle unless all items are quickly removed and

spread out so that the heat is dissipated. (Avoids risk of

spontaneous combustion).

■ Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

■ The interior of the dryer and dryer exhaust vent should be

cleaned periodically by qualiﬁed service personnel.

■ See “Electrical Requirements” section for grounding

instructions.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of ﬁre, electric shock, or injury to persons when using the dryer, follow basic precautions, including the

following:

SAVE THESE INSTRUCTIONS

■ Read all instructions before using the dryer.

■ This dryer is intended only for drying clothes and textiles

that have been washed in water. Do not use for any other

purpose.

■ WARNING: If you smell gas, do not use the dryer or any

electrical equipment nearby. Warn other people to clear the

area. Contact the dryer owner immediately.

■ Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to a

chemical reaction that could cause a load to catch ﬁre.

■ Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry-cleaning

solvents, other ﬂammable, or explosive substances as they

give off vapors that could ignite or explode.

■ Do not dry unwashed items in the dryer.

■ Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is used

near children.

■ Before the dryer is removed from service or discarded,

remove the doors to the dryer compartment.

■ Do not reach into the dryer if the drum is moving.

■ Do not open door while dryer is in operation. It will stop.

■ Do not install or store the dryer where it will be exposed to

water and/or the weather.

■ Do not tamper with controls.

5

Tools Needed:

8" (200 mm) 8" (200 mm) or 10" (250 mm) Flat-blade screwdriver Phillips screwdriver

or 10" (250 mm) Adjustable wrench

Pipe wrench that opens to 1" (25 mm)

Torx T-20

®†

security 1" (25 mm) Hex-head 5⁄16" (8 mm) Socket wrench Pliers (that open to

screwdriver or bit socket wrench 1

9

/

16

" [39 mm])

Level Utility knife 1/4" (6 mm) Nut driver 27" (686 mm)

Wood block

Caulk gun and caulk Vent clamps Pipe-joint compound Putty knife

(for installing new exhaust vent) suitable for gas type

Flashlight (optional) 1" (25 mm) Ruler or measuring tape

Open-end wrenches

TOOLS & PARTS

†® TORX and T-20 are registered trademarks of Acument Intellectual Properties, LLC.

Parts Supplied:

Security cotter pins (2)

6

DIMENSIONS/CLEARANCES

Dimensions

Minimum Clearances

Front View

Front View, Recessed Opening Side View, Recessed In Closet

Side View Back View

76

3

/4"

(1950 mm)

PD Models

74

1

/4"

(1886 mm)

PR Models

27"

(686 mm)

5"

(127 mm)

29"

(737 mm)

10

1

/

2

"

(267 mm)

7

Your dryer can be installed in a basement, laundry room,

or recessed area.

This dryer is not intended for installation in a mobile home.

Companion appliance location requirements should also be

considered.

IMPORTANT:

■ Do not install or store the dryer where it will be exposed

to water and/or the weather. Proper installation is your

responsibility.

■ This dryer must not be installed in a closet with a door.

You will need:

■ A grounded electrical outlet located within 6 ft. (1.8 m) of

where the power cord is attached to the back of the dryer.

See “Electrical Requirements.”

■ A level ﬂoor with a maximum slope of 1" (25 mm) under entire

dryer. Installing the dryer on soft ﬂoor surfaces, such as carpets

or surfaces with foam backing, is not recommended.

Dryer installation clearances

■ The location must be large enough to allow the dryer door to be

fully opened.

■ Additional spacing should be considered for ease of installation

and servicing. The door opens more than 180°.

■ Additional clearances might be required for wall, door, and ﬂoor

moldings.

■ Additional spacing of 1" (25 mm) on all sides of the dryer is

recommended to reduce noise transfer.

LOCATION REQUIREMENTS

When installing a gas dryer:

IMPORTANT: Observe all governing codes and ordinances.

■ Check code requirements: Some codes limit or do not

permit installation of clothes dryers in garages, closets, or

sleeping quarters. Contact your local building inspector.

■ Make sure that lower edges of the cabinet, plus the back and

bottom sides of the dryer, are free of obstructions to permit

adequate clearance of air openings for combustion air. See

“Recessed Area Installation Instructions” below for minimum

spacing requirements.

Recessed Area Installation Instructions

This dryer may be installed in a recessed area. For recessed area

installations, minimum clearances can be found on the warning

label on the rear of the dryer or in “Dimensions/Clearances.”

The installation spacing is in inches and is the minimum allowable.

Additional spacing should be considered for ease of installation,

servicing, and compliance with local codes and ordinances.

The dryer must be exhausted outdoors.

8

Gas Dryer Grounding

IMPORTANT: The dryer must be electrically grounded in

accordance with local codes and ordinances or, in the absence

of local codes, with the National Electrical Code, ANSI/NFPA 70,

latest edition, or Canadian Electrical Code, CSA C22.1. If codes

permit and a separate ground wire is used, it is recommended

that a qualiﬁed electrical installer determine that the ground path

is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

■ Do not ground to a gas pipe.

■ Do not have a fuse in the neutral or ground circuit.

■ A 120 volt, 60 Hz, AC only, 15- or 20-amp, fused electrical

circuit is required. A time-delay fuse or circuit breaker is also

recommended. It is recommended that a separate circuit

serving only this dryer be provided.

■ If codes permit and a separate ground wire is used, it is

recommended that a qualiﬁed electrician determine that

the ground path is adequate.

■ Check with a qualiﬁed electrician if you are not sure the dryer

is properly grounded.

GAS DRYER ELECTRICAL REQUIREMENTS

9

IMPORTANT: Observe all governing codes and ordinances.

This installation must conform with all local codes and ordinances.

In the absence of local codes, installation must conform with

American National Standard, National Fuel Gas Code ANSI

Z223.1/NFPA 54 or CAN/CSA B149.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

The design of this dryer has been certiﬁed by CSA International

for use at altitudes up to 10,000 feet (3048 m) above sea level at

the B.T.U. rating indicated on the model/serial plate. Burner input

adjustments are not required when the dryer is operated up to

this elevation.

When installed above 10,000 feet (3048 m), a four percent (4%)

reduction of the burner B.T.U. rating shown on the model/serial

plate is required for each 1,000 foot (305 m) increase in elevation.

For assistance when converting to other gas types and/or installing

above 10,000 feet (3048 m) elevation, contact your local service

company.

Gas Supply

GAS REQUIREMENTS

10

Electric Dryer GroundingIt is your responsibility:

■ To contact a qualiﬁed electrical installer.

■ To be sure that the electrical connection is adequate and in

conformance with the National Electrical Code, ANSI/NFPA

70-latest edition and all local codes and ordinances.

■ The National Electrical Code requires a 4-wire power supply

connection for homes built after 1996, dryer circuits involved

in remodeling after 1996, and all mobile home installations.

■ A copy of the above code standards can be obtained from:

National Fire Protection Association, One Batterymarch Park,

Quincy, MA 02269.

■ To supply the required 3 or 4 wire, single phase, 120/240 volt,

60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt

electrical supply, if speciﬁed on the serial/rating plate) on a

separate 30-amp circuit, fused on both sides of the line. A time

delay fuse or circuit breaker is recommended. Connect to an

individual branch circuit. Do not have a fuse in the neutral or

grounding circuit.

■ Do not use an extension cord.

■ If codes permit and a separate ground wire is used, it is

recommended that a qualiﬁed electrician determine that the

ground path is adequate.

Electrical Connection

To properly install your dryer, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

■ This dryer is manufactured ready to install with a 3-wire

electrical supply connection. The neutral ground conductor is

permanently connected to the neutral conductor (white wire)

within the dryer. If the dryer is installed with a 4-wire electrical

supply connection, the neutral ground conductor must be

removed from the external ground connector (green screw),

and secured under the neutral terminal (center or white wire)

of the terminal block. When the neutral ground conductor is

secured under the neutral terminal (center or white wire) of the

terminal block, the dryer cabinet is isolated from the neutral

conductor.

■ If local codes do not permit the connection of a neutral ground

wire to the neutral wire, see “Optional 3-wire connection”

section.

■ A 4-wire power supply connection must be used when the

appliance is installed in a location where grounding through

the neutral conductor is prohibited. Grounding through the

neutral is prohibited for (1) new branch-circuit installations

and (2) areas where local codes prohibit grounding through

the neutral conductor.

ELECTRIC DRYER ELECTRICAL REQUIREMENTS (U.S.A. ONLY)

11

Then choose a 4-wire power supply cord with ring or

spade terminals and UL listed strain relief. The 4-wire

power supply cord, at least 4 ft. (1.22 m) long, must

have four 10-gauge copper wires and match a 4-wire

receptacle of NEMA Type 14-30R. The ground wire

(ground conductor) may be either green or bare. The

neutral conductor must be identiﬁed by a white cover.

Electric Dryer Power Supply Cord

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with clothes

dryers. The kit should contain:

■ A UL listed 30-amp power supply cord, rated 120/240 volt

minimum. The cord should be type SRD or SRDT and be at

least 4 ft. (1.22 m) long. The wires that connect to the dryer

must end in ring terminals or “U” shaped spade terminals

with upturned ends.

■ A UL listed strain relief.

If your outlet looks like this:

4-wire

receptacle

(14-30R)

3-wire

receptacle

(10-30R)

Then choose a 3-wire power supply cord with ring

or spade terminals and UL listed strain relief. The

3-wire power supply cord, at least 4 ft. (1.22 m)

long, must have three 10-gauge copper wires and

match a 3-wire receptacle of NEMA Type 10-30R.

If your outlet looks like this:

ELECTRIC DRYER ELECTRICAL REQUIREMENTS (U.S.A. ONLY)

Direct Wire

If connecting by direct wire:

Direct wire cable must match power supply (4-wire or 3-wire)

and be:

■ Flexible armored cable or nonmetallic sheathed copper cable

(with ground wire), covered with ﬂexible metallic conduit.

All current-carrying wires must be insulated.

■ 10-gauge solid copper wire (do not use aluminum).

■ At least 5 ft. (1.52 m) long.

12

ELECTRIC DRYER ELECTRICAL REQUIREMENTS (CANADA ONLY)

Direct Wire

If connecting by direct wire:

Direct wire cable must match power supply (4-wire or 3-wire)

and be:

■ Cable must be rated to 60 Amps minimum.

■ Flexible armored cable or nonmetallic sheathed copper cable

(with ground wire), covered with ﬂexible metallic conduit.

All current-carrying wires must be insulated.

■ 6-gauge minimum solid copper wire (do not use aluminum).

■ At least 5 ft. (1.52 m) long.

13

DRYER VENTING REQUIREMENTS

WARNING: To reduce the risk of ﬁre, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

Dryer exhaust must not be connected into any gas vent, chimney,

wall, ceiling, attic, crawlspace, or a concealed space of a building.

Only rigid or ﬂexible metal vent shall be used for exhausting.

■ Only a 4" (102 mm) heavy, metal exhaust vent and clamps may

be used.

■ Do not use plastic or metal foil vent.

Rigid metal vent:

■ Recommended for best drying performance and to avoid

crushing and kinking.

Flexible metal vent: (Acceptable only if accessible to clean)

■ Must be fully extended and supported in ﬁnal dryer location.

■ Remove excess to avoid sagging and kinking that may result

in reduced airﬂow and poor performance.

■ Do not install in enclosed walls, ceilings, or ﬂoors.

■ The total length should not exceed 7

3

⁄

4

ft. (2.4 m).

NOTE: If using an existing vent system, clean lint from entire length

of the system and make sure exhaust hood is not plugged with

lint. Replace plastic or metal foil vents with rigid metal or ﬂexible

metal vents. Review “Vent System Chart” and if necessary, modify

existing vent system to achieve best drying performance.

4"

(102 mm)

4" (102 mm) Heavy, metal exhaust vent

Elbows:

■ 45° elbows provide better airﬂow than 90° elbows.

Clamps:

■ Use clamps to seal all joints.

■ Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into interior of duct and

catch lint. Do not use duct tape.

Better

Good

14

4" (102 mm) Diameter Exhaust Hoods

Box hood Louvered hood Angled hood

Vent Hoods

DRYER VENTING REQUIREMENTS

Exhaust hood must be at least 12" (305 mm) from the ground or

any object that may be in the path of the exhaust (such as ﬂowers,

rocks, bushes, or snow).

Maximum Vent Length/Vent Connection

Maximum length of vent system depends upon the type of vent

used, number of elbows, and type of exhaust hood.

Vent System Chart (Rigid Metal Vent)

No. of 90˚ Turns

Box and

Louvered Hood

Angled Hood

0 64 ft. (19.5 m) 58 ft. (17.7 m)

1 54 ft. (16.5 m) 48 ft. (14.6 m)

2 44 ft. (13.4 m) 38 ft. (11.6 m)

3 35 ft. (10.7 m) 29 ft. (8.8 m)

4 27 ft. (8.2 m) 21 ft. (6.4 m)

For vent systems not covered by the vent speciﬁcation chart,

see your parts distributor.

Provision must be made for enough air for combustion and

ventilation. (Check governing codes and ordinances.) See

“Recessed Area Installation Instructions” in the “Location

Requirements” sections.

A 4" (102 mm) outlet hood is preferred. However, a 2

1

⁄

2

" (64 mm)

outlet exhaust hood may be used. A 2

1

⁄

2

" (64 mm) outlet creates

greater back pressure than other hood types. For permanent

installation, a stationary vent system is required.

Connect Vent

1. If connecting to existing vent, make sure the vent is clean.

2. Using a 4" (102 mm) clamp, connect vent to exhaust outlet

in dryer.

NOTE: Do not remove vent collar.

Vent System Length

3. Tighten hose clamp with Phillips screwdriver.

4. Make sure the vent is secured to exhaust hood with a 4"

(102 mm) clamp.

5. Move dryer into ﬁnal position. Do not crush or kink vent.

Make sure dryer is level.

12" min.

(305 mm)

Vent collar

15

The outside end of main vent should have a sweep elbow directed

downward.

If main vent travels vertically through the roof, rather than through

wall, install a 180° sweep elbow on end of vent at least 2 ft.

(610 mm) above surface of roof.

The opening in wall or roof shall have a diameter 1⁄2" (13 mm)

larger than vent diameter. Vent should be centered in opening.

Do not install screening over end of vent for best performance.

12" min.

(305 mm)*

A main vent can be used for venting a group of dryers. The main

vent should be sized to remove 5663 l/min. (200 CFM) of air per

dryer. Large-capacity lint screens of proper design may be used in

main vent if checked and cleaned frequently. The room where the

dryers are located should have make-up air equal to or greater than

CFM of all the dryers in the room.

Back-draft Damper Kit, Part No. 3391910, is available from your

distributor and should be installed in the vent of each dryer to

keep exhausted air from returning into dryers and to keep exhaust

in balance within main vent. Unobstructed return air openings are

required.

Each vent should enter the main vent at an angle pointing in

the direction of the airﬂow. Vents entering from the opposite side

should be staggered to reduce the exhausted air from interfering

with the other vents.

The maximum angle of each vent entering the main vent should be

no more than 30°.

Keep air openings free of dry cleaning ﬂuid fumes. Fumes create

acids which, when drawn through the dryer heating units, can

damage dryers and items being dried.

A clean-out cover should be located on the main vent for periodic

cleaning of the vent system.

If an Exhaust Hood Cannot be Used Multiple Dryer Venting

DRYER VENTING REQUIREMENTS

24" min.

(610 mm)

* Minimum clearance above any

accumulation of snow, ice, or

debris such as leaves

1. Remove red cap from gas pipe on back of dryer.

2. Connect gas supply to dryer. Use a pipe thread compound

approved for the type of gas supplied. If ﬂexible metal tubing

is used, be certain there are no kinks.

If necessary for service, open the toe panel. Use a putty knife

to press on the toe panel locks located at the upper corners

of the toe panel. Pull downward on the toe panel to open.

Toe panel is hinged at the bottom.

3. Open the shut-off valve in the gas supply line and make sure

the dryer has its own gas supply opened.

4. Test all connections by brushing on an approved noncorrosive

leak-detection solution. Bubbles will show a leak. Correct any

leaks found.

Make Gas Connection

GAS SUPPLY CONNECTION

30˚ max.

air ow

Air flow

16

This dryer is equipped for use with natural gas. It is design-certiﬁed

by CSA International for LP (propane and butane) gases with

appropriate conversion. No attempt shall be made to convert dryer

from gas speciﬁed on serial/rating plate for use with a different gas

without consulting the serving gas supplier. Conversion must be

done by a qualiﬁed service technician.

Gas conversion kit part numbers are listed on gas valve burner base.

Type of Gas

GAS SUPPLY CONNECTION

Recommended Method

Provide a gas supply line of 1⁄2" (13 mm) rigid (IPS) pipe to dryer

location. Pipe joint compounds that resist action of LP gas must

be used. Do not use TEFLON

®†

tape. With LP gas, piping or tubing

size can be 1⁄2" (13 mm) minimum. Usually, LP gas suppliers

determine size and materials used in the system.

Gas Supply Pressure Testing

A 1/8" NPT minimum plugged tapping, accessible for gauge

testing, must be installed immediately downstream of the installed

shut-off valve to the dryer (as shown above). The dryer must

be disconnected from the gas supply piping system during any

pressure testing of the system at test pressures in excess of

1/2" psig (352 kg/m

2

).

Alternate Method

The gas supply may also be connected using 3⁄8" (10 mm)

approved copper or aluminum tubing. If the total length of the

supply line is more than 20 ft. (6.1 m), larger tubing will be

required.

If using natural gas, do not use copper tubing. Pipe joint

compounds that resist action of type of gas supplied must

be used.

Shut-off valve required

The supply line must be equipped with a manual shut-off valve

installed within 6 ft. (1.8 m) of dryer in accordance with National

Fuel Gas Code, ANSI Z223.1. This valve should be located in

same room as dryer. It should be in a location that allows ease

of opening and closing. Do not block access to shut-off valve.

In Canada, an individual manual shut-off valve must be installed in

accordance with the B149 installation codes CAN/CGA B149.1

and CAN/CGA B149.2.

Gas Supply Line

Flexible Metal Appliance Connector

It is recommended that a new ﬂexible stainless steel gas line,

design-certiﬁed by CSA International, be used for connecting the

dryer to the gas supply line. (The gas pipe which extends through

the lower rear of the dryer is provided with 3⁄8" male pipe thread.)

NOTE: Do not kink or damage the ﬂexible stainless steel gas line

when moving the dryer.

Rigid Pipe Connection

The rigid pipe connection requires a combination of pipe ﬁttings

to obtain an in-line connection to the dryer.

†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

17

Power Supply Cord Strain Relief

1. Insert strain relief.

2. Insert power cord into strain relief.

Remove Terminal Block Cover

Strain Relief

ELECTRIC DRYER ELECTRICAL CONNECTIONS (U.S.A. ONLY)

Direct Wire Strain Relief

1. Insert strain relief.

2. Insert conduit into strain relief and tighten clamp.

18

ELECTRIC DRYER ELECTRICAL CONNECTIONS

Power Cord

4-wire receptacle (NEMA Type 14-30R)

3-wire receptacle (NEMA Type 10-30R)

Standard Power Supply Cord Connectors

Flanged spade connector Ring Connector

Connecting Ground and Neutral Wires

1. Remove center terminal block screw and the ground wire

by removing the external ground connector screw.

2. Connect ground and neutral wire to center terminal block.

Connection Options

Connecting 4-Wire Connection: Power Supply Cord

IMPORTANT: A 4-wire connection is required where local codes

do not permit the use of 3-wire connections.

Direct Wire

4-wire direct

3-wire direct

1"

(25 mm)

5"

(127 mm)

Connecting Power Cord Ground Wire

3. Connect ground wire (green or bare) with external ground

connector screw.

Connecting Remaining Wires

4. Connect remaining wires with outer terminal block screws.

19

2. Connect neutral wire to center terminal block.

3. Connect remaining wires with outer terminal block screws.

Standard Power Cord Connectors

Flanged spade connector Ring Connector

Connecting Neutral Wire

1. Loosen or remove center terminal block screw.

IMPORTANT: A 4-wire connection is required where local codes

do not permit the use of 3-wire connections.

Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer

can be moved if needed.

Strip 5" (127 mm) of outer covering from end of cable, leaving bare

ground wire at 5" (127 mm). Cut 1

1

⁄

2

" (38 mm) from 3 remaining

wires. Strip insulation back 1" (25 mm). Shape ends of wires into

a hook shape.

Connecting 3-Wire Connection: Power Supply Cord

Connecting 4-Wire Connection: Direct Wire

ELECTRIC DRYER ELECTRICAL CONNECTIONS

Connecting Ground and Neutral Wires

1. Remove center terminal block screw and the ground wire by

removing the external ground connector screw.

20

2. Connect neutral wire to center terminal block.

3. Connect remaining wires to outer terminal block.

Connecting Ground and Neutral Wires (cont.)

2. Connect ground and neutral wire to center terminal block.

Connecting Direct Wire Ground

3. Connect ground wire (green or bare) with external ground

connector screw.

Use where local codes permit connecting cabinet-ground

conductor to neutral wire.

Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer

can be moved if needed.

Strip 3

1

⁄

2

" (89 mm) of outer covering from end of cable. Strip

insulation back 1" (25 mm). If using 3-wire cable with ground wire,

cut bare wire even with outer covering. Shape ends of wires into

a hook shape.

Connecting Neutral Wire

1. Loosen or remove center terminal block screw.

Connecting Remaining Wires

4. Connect remaining wires to outer terminal block.

Connecting 3-Wire Connection: Direct Wire

Connecting 4-Wire Connection: Direct Wire

ELECTRIC DRYER ELECTRICAL CONNECTIONS

La page charge ...

Maytag Commercial MLG26PRKWW Guide d'installation

Ce manuel convient également à

Maytag Commercial MLG26PRKWW Guide d'installation

dans d''autres langues

Documents connexes