Yamaha TF-RACK Guide de démarrage rapide

Marque: Yamaha

Modèle: TF-RACK

Catégorie: Mélangeurs audio

Taper: Guide de démarrage rapide

DIGITAL MIXER

V4.0 Quick Guide

Thank you for choosing a Yamaha TF-RACK Digital Mixer.

To take full advantage of the superior features and performance offered by

your TF-RACK mixer, and to enjoy years of trouble-free use, please read

this document carefully before operating your console.

TF-RACK Quick Guide

Contents

1. PRECAUTIONS ........................................................................................... 5

2. Introduction ................................................................................................ 7

2-1 Intended user ...................................................................................... 7

2-2 Intended usage ................................................................................... 7

2-3 Included items .................................................................................... 7

2-4 Documentation .................................................................................... 7

2-5 Information about software and ﬁrmware ........................................... 7

2-6 Nomenclature used in this document ................................................. 7

3. Panels.......................................................................................................... 8

3-1 Front panel .......................................................................................... 8

3-2 Rear panel .......................................................................................... 9

4. Workﬂow overview ................................................................................... 10

5. Connections ............................................................................................. 12

6. Controls and functions ............................................................................ 13

6-1 FADER BANK section ....................................................................... 13

6-2 iPad connector .................................................................................. 13

6-3 USB connector .................................................................................. 13

6-4 MUTE section .................................................................................... 13

6-5 TAP key ............................................................................................. 14

6-6 [CLEAR CUE] key ............................................................................. 14

6-7 USER DEFINED KEYS section .......................................................... 14

6-8 PHONES section ............................................................................... 14

6-9 USER DEFINED KNOBS section ...................................................... 14

6-10 Display section ................................................................................. 14

7. Displaying the conﬁguration screens .................................................... 16

8. Setup ......................................................................................................... 22

8-1 Setting the internal clock .................................................................. 22

8-2 Initialization (factory reset) ................................................................ 22

8-3 Removing the handles ...................................................................... 23

8-4 Rack-mounting the unit ..................................................................... 23

8-5 Installing an NY card ........................................................................ 24

9. TF-RACK Troubleshooting ....................................................................... 25

10. Speciﬁcations ......................................................................................... 26

TF-RACK Quick Guide

Explanation of Graphical Symbols

Explication des symboles

The lightning ash with arrowhead symbol within

an equilateral triangle is intended to alert the

user to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may

be of sufcient magnitude to constitute a risk of

electric shock to persons.

L’éclair avec une èche à l’intérieur d’un triangle

équilatéral est destiné à attirer l’attention de

l’utilisateur sur la présence d’une « tension dangereuse

» non isolée à l’intérieur de l’appareil, pouvant

être sufsamment élevée pour constituer un risque

d’électrocution.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and maintenance

(servicing) instructions in the literature

accompanying the product.

Le point d’exclamation à l’intérieur d’un triangle

équilatéral est destiné à attirer l’attention de

l’utilisateur sur la présence d’instructions

importantes sur l’emploi ou la maintenance

(réparation) de l’appareil dans la documentation

fournie.

The above warning is located on the top of the unit.

L’avertissement ci-dessus est situé sur le dessus de l’unité.

PRÉCAUTIONS

CONCERNANT LA

SÉCURITÉ

1 Lire ces instructions.

2 Conserver ces instructions.

3 Tenir compte de tous les avertissements.

4 Suivre toutes les instructions.

5 Ne pas utiliser ce produit à proximité d’eau.

6 Nettoyer uniquement avec un chiffon propre et sec.

7 Ne pas bloquer les oriﬁces de ventilation. Installer l’appareil

conformément aux instructions du fabricant.

8 Ne pas installer l’appareil à proximité d’une source de chaleur

comme un radiateur, une bouche de chaleur, un poêle ou tout

autre appareil (y compris un ampliﬁcateur) produisant de la

chaleur.

9 Ne pas modiﬁer le système de sécurité de la ﬁche polarisée

ou de la ﬁche de terre. Une ﬁche polarisée dispose de deux

broches dont une est plus large que l’autre. Une ﬁche de

terre dispose de deux broches et d’une troisième pour le

raccordement à la terre. Cette broche plus large ou cette

troisième broche est destinée à assurer la sécurité de

l’utilisateur. Si la ﬁche équipant l’appareil n’est pas compatible

avec les prises de courant disponibles, faire remplacer les

prises par un électricien.

10 Acheminer les cordons d’alimentation de sorte qu’ils ne soient

pas piétinés ni coincés, en faisant tout spécialement attention

aux ﬁches, prises de courant et au point de

sortie de l’appareil.

11 Utiliser exclusivement les ﬁxations et

accessoires spéciﬁés par le fabricant.

12 Utiliser exclusivement le chariot, le stand, le

trépied, le support ou la table recommandés

par le fabricant ou vendus avec cet appareil.

Si l’appareil est posé sur un chariot, déplacer

le chariot avec précaution pour éviter tout

risque de chute et de blessure.

13 Débrancher l’appareil en cas d’orage ou lorsqu’il doit rester

hors service pendant une période prolongée.

14 Conﬁer toute réparation à un personnel qualiﬁé. Faire réparer

l’appareil s’il a subi tout dommage, par exemple si la ﬁche ou le

cordon d’alimentation est endommagé, si du liquide a coulé ou

des objets sont tombés à l’intérieur de l’appareil, si l’appareil

a été exposé à la pluie ou à de l’humidité, si l’appareil ne

fonctionne pas normalement ou est tombé.

AVERTISSEMENT

POUR RÉDUIRE LES RISQUES D’INCENDIE OU DE DÉCHARGE

ÉLECTRIQUE, N’EXPOSEZ PAS CET APPAREIL À LA PLUIE OU À

L’HUMIDITÉ.

UL60065_03:

IMPORTANT SAFETY

INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including ampliﬁers) that

produce heat.

9 Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not ﬁt into your outlet,

consult an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11 Only use attachments/accessories speciﬁed by

the manufacturer.

12 Use only with the cart, stand, tripod, bracket,

or table speciﬁed by the manufacturer, or

sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms

or when unused for long periods of time.

14 Refer all servicing to qualiﬁed service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate

normally, or has been dropped.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

UL60065_03:

TF-RACK Quick Guide

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modiﬁcations not expressly approved

by Yamaha may void your authority, granted by the

FCC, to use the product.

2. IMPORTANT: When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with

this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found

to comply with the requirements listed in FCC

Regulations, Part 15 for Class “B” digital devices.

Compliance with these requirements provides a

reasonable level of assurance that your use of this

product in a residential environment will not result in

harmful interference with other electronic devices. This

equipment generates/uses radio frequencies and, if

not installed and used according to the instructions

found in the users manual, may cause interference

harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If

this product is found to be the source of interference,

which can be determined by turning the unit “OFF”

and “ON”, please try to eliminate the problem by using

one of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch

(circuit breaker or fuse) circuits or install AC line

ﬁlter/s.

In the case of radio or TV interference, relocate/

reorient the antenna. If the antenna lead-in is 300 ohm

ribbon lead, change the lead-in to co-axial type cable.

If these corrective measures do not produce

satisfactory results, please contact the local retailer

authorized to distribute this type of product. If you

can not locate the appropriate retailer, please contact

Yamaha Corporation of America, Electronic Service

Division, 6600 Orangethorpe Ave, Buena Park,

CA90620

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

(class B)

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena

Park, Calif. 90620

Telephone : 714-522-9011

Type of Equipment : DIGITAL MIXER

Model Name : TF-RACK

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received

including interference that may cause undesired

operation.

See user manual instructions if interference to radio

reception is suspected.

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA

(FCC DoC)

IMPORTANT NOTICE

FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT. The wires in this mains lead are coloured in

accordance with the following code:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug proceed

as follows:

The wire which is coloured GREEN-and-YELLOW must

be connected to the terminal in the plug which is marked

by the letter E or by the safety earth symbol or colored

GREEN or GREEN-and-YELLOW.

The wire which is coloured BLUE must be connected to

the terminal which is marked with the letter N or coloured

BLACK.

The wire which is coloured BLUE must be connected to

the terminal which is marked with the letter N or coloured

BLACK.

(3 wires)

이 기기는 가정용(B급) 전자파적합기기로서 주로

가정에서 사용하는 것을 목적으로 하며, 모든

지역에서 사용할 수 있습니다.

(class b korea)

NEDERLAND / THE NETHERLANDS

• Dit apparaat bevat een lithium batterij voor geheugen

back-up.

• This apparatus contains a lithium battery for memory

back-up.

• Raadpleeg uw leverancier over de verwijdering van de

batterij op het moment dat u het apparaat ann het einde

van de levensduur of gelieve dan contact op te nemen

met de vertegenwoordiging van Yamaha in uw land.

• For the removal of the battery at the moment of the

disposal at the end of life please consult your retailer or

Yamaha representative ofﬁce in your country.

• Gooi de batterij niet weg, maar lever hem in als KCA.

• Do not throw away the battery. Instead, hand it in as

small chemical waste.

(lithium disposal)

This product contains a battery that contains perchlorate

material.

Perchlorate Material—special handling may apply,

See www.dtsc.ca.gov/hazardouswaste/perchlorate.

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

(Perchlorate)

In Finland: Laite on liitettävä suojamaadoituskoskettimilla

varustettuun pistorasiaan.

In Norway: Apparatet må tilkoples jordet stikkontakt.

In Sweden: Apparaten skall anslutas till jordat uttag.

(class I hokuo)

ADVARSEL!

Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering.

Udskiftning må kun ske med batteri af samme fabrikat og

type. Levér det brugte batteri tilbage til leverandoren.

VARNING

Explosionsfara vid felaktigt batteribyte. Använd samma

batterityp eller en ekvivalent typ som rekommenderas

av apparattillverkaren. Kassera använt batteri enligt

fabrikantens instruktion.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu.

Vaihda paristo ainoastaan laitevalmistajan suosittelemaan

tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden

mukaisesti.

(lithium caution)

TF-RACK Quick Guide

1. PRECAUTIONS

Water warning

• Do not expose the device to rain, use it near water or in

damp or wet conditions, or place on it any containers (such

as vases, bottles or glasses) containing liquids which might

spill into any openings. If any liquid such as water seeps

into the device, turn off the power immediately and unplug

the power cord from the AC outlet. Then have the device

inspected by qualiﬁed Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

Hearing loss

• Avoid setting all equalizer controls and faders to their

maximum. Depending on the condition of the connected

devices, doing so may result in feedback that can cause

hearing loss and damage the speakers.

• Do not use headphones for a long period of time at a

high or uncomfortable volume level, since this can cause

permanent hearing loss. If you experience any hearing loss

or ringing in the ears, consult a physician.

• When turning on the AC power in your audio system, always

turn on the power ampliﬁer LAST, to avoid hearing loss and

speaker damage. When turning the power off, the power

ampliﬁer should be turned off FIRST for the same reason.

Fire warning

• Do not place any burning items or open ﬂames near the

device, since they may cause a ﬁre.

If you notice any abnormality

• If any of the following problems occur, immediately turn off

the power switch and disconnect the electric plug from the

outlet.

- The power cord or plug becomes frayed or damaged.

- Unusual smells or smoke are emitted.

- Some object has been dropped into the device.

- There is a sudden loss of sound during use of the device.

- Cracks or other visible damage appear on the device.

Then have the device inspected or repaired by qualiﬁed

Yamaha service personnel.

• If this device should be dropped or damaged, immediately

turn off the power switch, disconnect the electric plug from

the outlet, and have the device inspected by qualiﬁed

Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below

to avoid the possibility of physical injury to you or

others, or damage to the device or other property.

These precautions include, but are not limited to,

the following:

Power supply/power cord

• When removing the electric plug from the device or an

outlet, always hold the plug itself and not the cord. Pulling

by the cord can damage it.

Location

• Do not place the device in an unstable position where it

might accidentally fall over and cause injuries.

• Do not block the vents. This device has ventilation holes at

the rear to prevent the internal temperature from becoming

too high. In particular, do not place the device on its

side or upside down. Inadequate ventilation can result in

overheating, possibly causing damage to the device(s), or

even ﬁre.

• When installing the device:

- Do not cover it with any cloth.

- Do not install it on a carpet or rug.

- Make sure the top surface faces up; do not install on its

sides or upside down.

- Do not use the device in a conﬁned, poorly-ventilated

location.

Inadequate ventilation can result in overheating, possibly

causing damage to the device(s), or even ﬁre. If this device is

to be used in a small space other than an EIA-standard rack,

make sure that there is adequate space around the device: at

least 10cm above, 10cm at the sides and 20cm behind.

• Do not place the device in a location where it may come into

contact with corrosive gases or salt air. Doing so may result

in malfunction.

• Before moving the device, remove all connected cables.

• If the device is mounted in an EIA standard rack, carefully

read the section “Rack-mounting the unit” on page 23.

Inadequate ventilation can result in overheating, possibly

causing damage to the device(s), malfunction, or even ﬁre.

Connections

• Before connecting the device to other devices, turn off the

power for all devices. Also, before turning the power of all

devices on or off, make sure that all volume levels are set to

the minimum. Failing to do so may result in electric shock,

hearing loss, or equipment damage.

Maintenance

• Remove the power plug from the AC outlet when cleaning

the device.

PA-7 1/2

PLEASE READ CAREFULLY

BEFORE PROCEEDING

Please keep this manual in a safe place

for future reference.

WARNING

Always follow the basic precautions listed below to

avoid the possibility of serious injury or even death

from electrical shock, short-circuiting, damages, ﬁre

or other hazards. These precautions include, but are

not limited to, the following:

Power supply/power cord

• Do not place the power cord near heat sources such

as heaters or radiators, and do not excessively bend or

otherwise damage the cord, place heavy objects on it, or

place it in a position where anyone could walk on, trip over,

or roll anything over it.

• Only use the voltage speciﬁed as correct for the device. The

required voltage is printed on the name plate of the device.

• Use only the supplied power cord/plug.

If you intend to use the device in an area other than in the

one you purchased, the included power cord may not be

compatible. Please check with your Yamaha dealer.

• Check the electric plug periodically and remove any dirt or

dust which may have accumulated on it.

• When setting up the device, make sure that the AC outlet

you are using is easily accessible. If some trouble or

malfunction occurs, immediately turn off the power switch

and disconnect the plug from the outlet. Even when the

power switch is turned off, as long as the power cord is not

unplugged from the wall AC outlet, the device will not be

disconnected from the power source.

• Remove the electric plug from the outlet when the device

is not to be used for extended periods of time, or during

electrical storms.

• Be sure to connect to an appropriate outlet with a protective

grounding connection.

Do not open

• This device contains no user-serviceable parts. Do not

open the device or attempt to disassemble the internal

parts or modify them in any way. If it should appear to be

malfunctioning, discontinue use immediately and have it

inspected by qualiﬁed Yamaha service personnel.

TF-RACK Quick Guide

PRECAUTIONS

Handling caution

• Do not insert your ﬁngers or hands in any gaps or openings

on the device (vents, panel, etc.).

• Avoid inserting or dropping foreign objects (paper, plastic,

metal, etc.) into any gaps or openings on the device (vents,

panel, etc.) If this happens, immediately turn off the power,

unplug the power cord from the AC outlet, and have the

device inspected by qualiﬁed Yamaha service personnel.

• Do not rest your weight on the device or place heavy

objects on it, and avoid use excessive force on the buttons,

switches or connectors to prevent injuries.

• Avoid pulling the connected cables to prevent injuries.

Backup battery

• Do not replace the backup battery by yourself. Doing so

may cause an explosion and/or damage to the device(s).

When the backup battery needs to be replaced, “Low

Battery” or “No Battery” will appear on the display. In this

case, contact your Yamaha dealer and have qualiﬁed

Yamaha service personnel replace the backup battery.

Yamaha cannot be held responsible for damage caused by

improper use or modiﬁcations to the device, or data that is

lost or destroyed.

PA-7 2/2

NOTICE

To avoid the possibility of malfunction/ damage to

the product, damage to data, or damage to other

property, follow the notices below.

Handling and maintenance

• Do not use the device in the vicinity of a TV, radio, AV

equipment, mobile phone, or other electric devices.

Otherwise, the device, TV, or radio may generate noise.

• Do not expose the device to excessive dust or vibration,

or extreme cold or heat (such as in direct sunlight, near a

heater, or in a car during the day), in order to prevent the

possibility of panel disﬁguration, unstable operation, or

damage to the internal components.

• Do not place vinyl, plastic or rubber objects on the device,

since this might discolor the panel.

When cleaning the device, use a dry and soft cloth. Do not

use paint thinners, solvents, cleaning ﬂuids, or chemical-

impregnated wiping cloths.

• Condensation can occur in the device due to rapid, drastic

changes in ambient temperature—when the device is

moved from one location to another, or air conditioning

is turned on or off, for example. Using the device while

condensation is present can cause damage. If there is

reason to believe that condensation might have occurred,

leave the device for several hours without turning on the

power until the condensation has completely dried out.

• The rubber feet included in this package can be attached to

the speaker to prevent slippage when it is to be used on a

slippery surface.

• Always turn the power off when the device is not in use.

Saving data

•

This device has a built-in backup battery that maintains data in

internal memory even when the device’s power is switched off.

The backup battery will eventually become depleted, however,

and when that happens the contents of the internal memory will

be lost.* To prevent loss of data be sure to replace the backup

battery before it becomes fully depleted. When the remaining

capacity of the backup battery becomes so low that it needs

to be replaced a “Low Battery” or “No Battery” message will

appear on the display during operation or when the device

is powered on. If either of these messages appears do not

turn off the power and immediately transfer any data you want

to save to a computer or other external storage device, then

have qualiﬁed Yamaha service personnel replace the backup

battery. The average life of the internal backup battery is

approximately 5 years, depending on operating conditions.

* Data items maintained in the internal memory by the

backup battery are as follows:

• Internal clock information

Data items other than those described above are stored in

memory that does not require backup power, and will be

retained even if the backup battery fails.

Connectors

• XLR-type connectors are wired as follows (IEC60268

standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).

Information

• Copying of the commercially available musical data

including but not limited to MIDI data and/or audio data is

strictly prohibited except for your personal use.

• The illustrations and LCD screens as shown in this manual

are for instructional purposes only.

• Steinberg Media Technologies GmbH and Yamaha

Corporation make no representations or warranties with

regard to the use of the software and documentation and

cannot be held responsible for the results of the use of this

manual and the software.

• Windows is a registered trademark of Microsoft®

Corporation in the United States and other countries.

• Apple, iPad and iPod are trademarks of Apple Inc.,

registered in the U.S. and other countries.

• IOS is a trademark or registered trademark of Cisco in the

U.S. and other countries and is used under license.

• Steinberg and Nuendo are registered trademarks of

Steinberg Media Technologies GmbH.

• The company names and product names in this manual are

the trademarks or registered trademarks of their respective

companies.

• Software may be revised and updated without prior notice.

•

This product contains recyclable components. When disposing

of this product, please contact the appropriate local authorities.

European Models

Purchaser/User Information speciﬁed in EN55103-2:2009.

Conforms to Environments: E1, E2, E3 and E4

Information for users on collection

and disposal of old equipment:

This symbol on the products,

packaging, and/or accompanying

documents means that used electrical

and electronic products should not be

mixed with general household waste.

For proper treatment, recovery and

recycling of old products, please take

them to applicable collection points,

in accordance with your national

legislation.

By disposing of these products correctly, you will help to

save valuable resources and prevent any potential negative

effects on human health and the environment which could

otherwise arise from inappropriate waste handling.

For more information about collection and recycling of

old products, please contact your local municipality, your

waste disposal service or the point of sale where you

purchased the items.

For business users in the European Union:

If you wish to discard electrical and electronic equipment,

please contact your dealer or supplier for further

information.

Information on Disposal in other Countries outside

the European Union:

This symbol is only valid in the European Union. If you wish

to discard these items, please contact your local authorities

or dealer and ask for the correct method of disposal.

(weee_eu_en_02)

TF-RACK Quick Guide

2-1 Intended user

This product was designed for users who are familiar

with using analog mixers as part of a PA system.

2-2 Intended usage

This product was designed to be installed in a rack

mount and used in a variety of locations, such as shops

and event spaces, to mix multiple audio sources, such

as live band instruments or audio devices used at

corporate events.

2-3 Included items

• Power cord

• Quick Guide (this document)

• Rubber feet (×4)

• Nuendo Live (DAW software)

2-4 Documentation

Quick Guide (this document)

This document primarily explains panel controls,

functions, and basic operation of the product.

Reference Manual (PDF; downloadable from

the website)

This document primarily explains details about

functions, production operation, and effects

parameters.

The Reference Manual covers the TF5/TF3/TF1

consoles as well as the TF-RACK (hereafter referred to

as the “TF series”) and is available on the Yamaha Pro

Audio website.

http://www.yamahaproaudio.com/

Using the Reference Manual

The Reference Manual is an electronic ﬁle in PDF

format. You can read this document on a computer.

Use Adobe® Acrobat Reader DC® to read this book

on screen, search for words very quickly, print speciﬁc

pages, or click links to display sections of special

interest. The ability to search for words, or to follow

links directly to relevant sections in the document,

are helpful attributes of this electronic ﬁle format. We

encourage you to take advantage of these beneﬁts.

You can download the latest Adobe Acrobat Reader

DC application from the website listed below.

http://www.adobe.com/

2-5 Information about software and

ﬁrmware

Software

Your TF-series mixer can be used with a variety of utility

software.

• TF Editor

This application enables you to set up and operate

the unit from a connected computer. You can also use

the application to back up mixer settings or set mixer

parameters without connecting the unit.

• TF StageMix

This app allows you to use your iPad and a Wi-Fi

connection to remote control the unit.

• MonitorMix

This app allows you to use your mobile device and a

Wi-Fi connection to adjust the TF-series mixer’s AUX

Send remotely.

• Yamaha Steinberg USB Driver (Windows only)

This driver software is required when connecting the

mixer to your computer. It supports up to 34 channels

of audio input and 34 channels of audio output.

Information about the software described here is

available on the Yamaha Pro Audio website.

http://www.yamahaproaudio.com/

Information about downloading, installing and setting

up the software described here is available on the

website listed above. In addition, refer to the installation

guide that is included with each program.

Firmware

The ﬁrmware contained in your TF-series mixer can be

updated to take advantage of new features, feature

improvements, and bug ﬁxes.

Details about updating the ﬁrmware are available

online.

http://www.yamahaproaudio.com/

For information about updating and setting up the

mixer, please refer to the ﬁrmware update guide

available on the website.

2-6 Nomenclature used in this

document

In this document, switch-type controls on the panel are

called “keys.”

Controls located on the panel are enclosed in [square

brackets] (e.g., the [CUE] key) to distinguish them

from virtual buttons and knobs displayed on screen.

For certain controls, the name of the section appears

before the brackets (e.g., FADER BANK [INPUT] key).

The model number, serial number, power requirements,

etc., may be found on or near the name plate, which is

at the top of the unit. You should note this serial number

in the space provided below and retain this manual as a

permanent record of your purchase to aid identiﬁcation

in the event of theft.

Model No.

Serial No.

2. Introduction

TF-RACK Quick Guide

1 FADER BANK section

2 iPad connector

3 USB connector

4 MUTE section

5 TAP key

6 CLEAR CUE key

7 USER DEFINED KEYS section

8 PHONES section

9 USER DEFINED KNOBS section

0 Display section

a Ventilation holes

To prevent overheating, do not block the ventilation

holes.

3. Panels

3-1 Front panel

⑦

⑧

⑨⑪

⑩ ② ⑪①

③

④ ⑤

⑥

TF-RACK Quick Guide

Panels

1 OMNI OUT jacks

Analog signal output jacks. Jacks 1–8 are male XLR-

3-32 type connectors; jacks 9–16 are TRS phone

connectors. These jacks are used to output AUX/

MATRIX channels and STEREO channels. Nominal

output level is +4 dBu. You can select which signal is

output on the OMNI OUT screen.

2 ST IN jacks

Stereo input jacks that can be used for connecting a

CD player or other line level device. These jacks are

unbalanced female RCA jacks. Nominal input level is

-10 dBV.

3 INPUT jacks

Combination jacks that support both XLR and TRS

phone connectors. Use these jacks to connect mics

and instruments. Nominal input level is -62 dBu to

+10 dBu. The head amp setting for each jack is saved

in memory.

4 NETWORK connector

RJ-45 jack used to connect the unit to a computer or

smart device via an Ethernet cable (CAT5e or higher

recommended). Use STP (Shielded Twisted Pair) cable

to prevent electromagnetic interference.

5 USB TO HOST connector

USB connector used to connect the unit to a computer,

allowing the unit to function as an audio interface.

Supports input and output for up to 34 channels of up

to 48 kHz, 24-bit audio. When using with a computer

running Microsoft Windows, the Yamaha Steinberg

USB Driver is required. When using a Mac, Core Audio

is used and therefore no extra drivers are required.

6 FOOT SW jack

Used for connecting an optional FC5 foot switch. You

can use the connected foot switch as an effect bypass

switch, a mute switch, or use it to tap the delay time.

7 Expansion slot

Allows you to install an NY card, such as the NY64-D Audio

Interface Card. (Installing an NY card → page 24)

8 Exhaust holes

The unit contains a built-in cooling fan. These holes are

used to expel air from the unit. To prevent overheating

or malfunction, do not block the exhaust holes.

Power switch

When the switch is in the

position, the power is on.

When the switch is in the

position, the power is off.

0 AC IN connector

Connect the included power cord. When connecting to a

power outlet, ﬁrst connect the power cord to the console,

then connect the power cord to the power outlet.

CAUTION

• Make sure the unit is turned off before connecting

or disconnecting the power cord.

• Disconnect the power cord from the outlet when the unit

will not be used for extended periods of time.

3-2 Rear panel

① ③

⑤⑥⑨⑩ ⑦ ④

②

⑧

TF-RACK Quick Guide

4. Workﬂow overview

Here’s a brief overview of how to start using the TF-RACK.

Connect

Connect the instruments and mics.

Connect output devices such as powered speakers.

Connect the included power cord to the AC IN

connector.

When your connections are ﬁnished, turn on the power.

NOTICE

• To ensure that the state is saved properly,

wait at least 10 seconds after performing the

last operation before turning the product off.

This product regularly saves the state of its

workspace so that it can return to the previous

state when the product is turned on.

• After turning the unit off, wait for at least 6

seconds before turning it on again. Rapidly

turning the unit off and on in succession can

cause it to malfunction.

AC IN connector

Power switch

Use Presets to Set Up Each Channel

Step1

Select a channel.

C C C L15 R15 C R10 L63

-30

-11

-28

30%

-26

30%

-40

30%

-40

30%

-48

-18

-30

30%

-26

Step2

Press the Library key ( ) to access the Library

and recall a Preset.

Step3

Adjust the channel’s parameters.

Adjust the input gain, EQ, compressor, and gate.

These can be adjusted from the OVERVIEW screen

or the individual conﬁguration screens (page 16).

> Repeat steps 1 to 3 and set up each channel.

Display section

Library key (

)

Input gain adjustment

(INPUT screen)

NOTE

You can set up channels without using Presets. For details about the available features and parameters, refer to the Reference Manual.

TF-RACK Quick Guide

Workﬂow overview

Adjust the Mix

Do a sound check and adjust the overall mix.

• Adjusting each channel using the FADER section on

the OVERVIEW screen (page 18)

• Adjusting SEND TO AUX for the level sent to AUX for

each channel (page 19)

• Muting all input channels or effects (page 13)

• Turning effects on and off, adjusting the overall level

of effects “FX1/FX2” (page 19)

MUTE

Save Your Settings

You can save your entire mix setup as a Scene.

Scenes can be recalled later as needed.

(SCENE window page 16)

You can also save individual channel setups by

overwriting existing Presets or by saving them as new

Presets in the Library screen.

HINT

Using USER DEFINED KEYS

When the device is in the default state, USER DEFINED KEYS

(page 14) are conﬁgured as “Direct Scene Recall” keys. You

can save a Scene by pressing and holding down one of the

USER DEFINED KEYS, and recall a Scene by pressing one of the

USER DEFINED KEYS.

What is a “Preset”?

A Preset is a ﬁle stored in the Library (

)

that contains channel settings such as the

type of input (instrument or mic), equalizer

and compression settings, etc. The default

Presets contain settings for various types

of instruments, so you can use them as a

starting point when setting up a channel.

You can edit Presets and save them as new

Presets.

What is a “Scene”?

A Scene is a ﬁle that contains all the settings for

every channel in your mix.

FadeTime 1.0

Conventional z

ero console

Fade

Time

1.0s

Saving a Scene

Recalling a Scene

TF-RACK Quick Guide

Default signal routing for each output jack

OMNI OUT 1 AUX1 OUT

OMNI OUT 2 AUX2 OUT

: :

OMNI OUT 6 AUX6 OUT

OMNI OUT 7 STEREO L OUT

OMNI OUT 8 STEREO R OUT

OMNI OUT 9 AUX9 OUT

OMNI OUT 10 AUX10 OUT

: :

OMNI OUT 14 AUX14 OUT

OMNI OUT 15 MONITOR L OUT

OMNI OUT 16 MONITOR R OUT

Each OMNI OUT jack is conﬁgured by default to output a

bus. You can change the bus that is output on the

SETUP

→

OMNI OUT PATCH screen.

The OMNI OUT jacks can be conﬁgured to output the

following signals.

AUX1–AUX20, MATRIX1–4, STEREO L, STEREO R, SUB,

MONITOR L, MONITOR R, NO ASSIGN (no output signal

assigned).

5. Connections

Default signal routing for each channel

CHANNEL TF-RACK

CH 1 INPUT 1

: :

CH 16 INPUT 16

CH 17 INPUT 1

: :

CH 32 INPUT 16

ST IN 1L PLAYBACK L

ST IN 1R PLAYBACK R

ST IN 2L ST IN L

ST IN 2R ST IN R

Default signal routing for each channel is shown above.

To change the signal routing, use the INPUT screen (page

18).

HINT

What if I’m using condenser mics?

Phantom power must be supplied to condenser mics.

Some direct boxes also need phantom power. When using

phantom power, ﬁrst set “+48V Master” on the SETUP

screen to on, then turn phantom power on or off for each

channel on the corresponding channel’s INPUT screen.

Make sure you turn phantom power off if it is not needed.

For more details, refer to the Reference Manual.

Why can’t I hear anything?

• Is the fader that corresponds to the desired INPUT jack

raised?

• Does the input select for each channel match each

INPUT jack?

• Is the channel’s head amp gain set too low?

• Is the channel’s mute turned on?

• Is the channel muted?

Connecting inputsConnecting outputs

Powered speakers

(ﬂoor monitors)

Powered speakers

(front speakers)

Mic

FC5 (optional)

Computer

(DAW software)

USB 2.0

CD player

Wireless mic receiver

TF-RACK Quick Guide

6-2 iPad connector

Allows you to connect an iOS device or a USB storage

device.

To connect an iOS device, use the dedicated cable that

was included with the device. This connector allows you

to use audio ﬁles on your iOS device as background

music.

When a USB storage device is connected, you can use

the device to play audio ﬁles or record the mixer’s output

directly and save it as an audio ﬁle (format: WAV).

NOTE

When using a USB storage device for recording, use a hard disk

drive or other high-speed device. (USB memory drives are not

guaranteed to function properly.)

For information about compatible iOS devices, visit the

Yamaha pro audio website.

http://www.yamahaproaudio.com/

6-3 USB connector

Used for connecting USB memory drives.

You can connect a USB memory drive and read/write data

from/to the drive.

Supported formats for USB memory drives

Drives formatted using FAT32 are supported.

 Preventing accidental erasure

Some USB memory drives offer a write-protect feature

which prevents accidental data erasure. If you save

important data on a USB memory drive, we recommend

using the drive’s write-protect feature to protect your data

from being erased. Conversely, make sure the drive’s

write-protect feature is turned off before trying to save

data to the drive.

NOTE

The ACCESS indicator is displayed in the upper right of the

screen while data is being accessed (read, written, erased,

etc.). While this indicator is displayed, do not turn off the unit or

disconnect the USB memory drive. The unit, the drive, and data

stored on the drive could become damaged.

6-4 MUTE section

Used to mute all channels in a mute group.

①

②

1 [INPUT] key

Allows you to mute all channels at once. The key lights

when the mute group is muted.

2 [FX] key

Allows you to mute the FX module. Insertion effects for

channels in AUX9/10–AUX19/20 are bypassed. The

key lights when the mute group is muted.

HINT

You can remove certain input and FX channels from the mute

group by turning MUTE SAFE on for the desired channels.

This section brieﬂy introduces the console’s features.

NOTE

For details about the available features and parameters, refer to

the Reference Manual.

6-1 FADER BANK section

Allows you to change the fader bank displayed in the

OVERVIEW screen.

The keys light to indicate which fader bank is currently

selected.

①

②

③

④

1 [INPUT] key

Displays input channels.

2 [GROUP] key

Displays group channels.

3 [OUTPUT] key

Displays output channels.

4 [CUSTOM] key

Displays the channels assigned to the custom fader

bank.

6. Controls and functions

TF-RACK Quick Guide

Controls and functions

6-5 TAP key

Allows you to tap and set the delay time or modulation

speed used for effects on FX1/FX2 and AUX9/10–

AUX19/20.

The key ﬂashes in time with the tempo. The tempo you tap

on the [TAP] key is applied to effects that have “Sync” set

to “On”.

You can set the [TAP] key ﬂashing to “Off” in the SETUP

screen.

6-6 [CLEAR CUE] key

Turns off the CUE for all channels.

The key lights when the CUE is turned on.

6-7 USER DEFINED KEYS section

These keys can be customized to control the desired

function.

Various functions are assigned by default, such as Direct

Scene Recall.

You can assign parameters to each knob in the SETUP

screen.

6-8 PHONES section

①

②

1 [PHONES] jack

This is the headphones jack used to monitor signals

selected for MONITOR or CUE.

2 [LEVEL] knob

Controls the level of the [PHONES] jack output.

6-9 USER DEFINED KNOBS section

These knobs allow you to adjust the parameters that

you’ve assigned to them.

You can assign parameters to each knob in the SETUP

screen.

6-10 Display section

Allows to you control the console by touching the

touchscreen. You can also use the knobs to perform ﬁne

adjustments. You can dive further into various features by

pressing the keys to display contextual menus.

①

②

③

④

⑤

⑥

1 Display

You can use familiar touchscreen operations, such as

touch, double-touch, sliding, swiping, pinching in, and

pinching out.

2 Library key (

)

Displays the Library screen, from which you can recall

Presets.

3 Home key (

)

Returns the display to the OVERVIEW screen. The

display will change with the content set in Key

Function on the PREFERENCE screen by pressing the

home key while the OVERVIEW screen is displayed.

4 Menu key (

)

Displays the menu for the current operation. The key

lights when a menu is available.

5 [TOUCH AND TURN] knob

Allows you to control the parameter of the feature

selected on the display.

For information about how to control the parameters,

see page 15.

6 [SHIFT] key

Provides additional functionality, such as allowing

you to switch between the F (frequency) and G (gain)

parameters of the EQ handle.

TF-RACK Quick Guide

Controls and functions

Operating the display

• Changing screens

The screen switches when you touch an on-screen

button.

You can touch an area of the screen to select

that area, then touch it again to switch to the

conﬁguration screen for that area. If an area is

displayed in pink when selected, the area contains

a parameter that can be controlled with the [TOUCH

AND TURN] knob.

To return to the OVERVIEW screen, press the Home

key (

NOTE

In the SETUP ¦ PREFERENCE screen, select the contents to be

displayed in the OVERVIEW screen by using the Key Function ¦

[HOME] key. When multiple items are selected, the display will

change with each press of the Home key ( ).

OVERVIEW CH STRIP

section (page 19)

OVERVIEW SELECTED

CHANNEL section

(page 20)

OVERVIEW FADER section

• Scrolling

In the OVERVIEW screen, you can slide the screen

left and right to view different channels.

When a scroll bar is displayed, you can slide the

screen up and down to view more content. To scroll

quickly, simply use a swiping gesture.

• Adjusting the Q (steepness) of the EQ

When in manual mode on the EQ screen, select one

of the handles and pinch in or out to adjust the Q.

NOTE

This functionality is not available when multiple parameters can

be controlled by one knob (i.e., 1-knob mode). Use the button at

the top of the screen to switch to manual mode.

Using the [TOUCH AND TURN] knob to control

parameters

As shown below, touch the parameter you want to

control (

) and then turn the [TOUCH AND TURN]

knob as desired (

). A pink selection area is

displayed around the selected parameter.

In the OVERVIEW screen, touch an area of the screen

to adjust the parameter in that area. In this case, a

pink selection area is displayed around the selected

area.

[TOUCH AND TURN] knob

HINT

What is “1-knob” mode?

1-knob mode allows you to control multiple EQ or compressor

parameters by simply turning the [TOUCH AND TURN] knob.

When 1-knob mode is enabled, parameters cannot be adjusted

individually. You can turn 1-knob mode on and off from the EQ

and compressor screens.

TF-RACK Quick Guide

7. Displaying the conﬁguration screens

You can view the following screens by touching the buttons in the OVERVIEW screen. To return to the OVERVIEW screen, press the Home key ( ) below the display.

Conventional z

ero console

Fade

Time

1.0s

Input

Output

PFL Trim

frame

PFL Trim

SCENE

Used to recall previously saved mixer

setups.

OVERVIEW

Allows you to select the user, change

account settings, and use the console

lock feature.

CH VIEW

Provides an overall view of a channel’s settings.

You can adjust settings on this screen or switch

to the dedicated screen for each setting. You

can also edit the Channel Name on this screen.

METER

Displays the input and output level.

CUE/MONITOR/OSCILLATOR

Used to manage CUE/monitor source and

control oscillators.

TF-RACK Quick Guide

Displaying the conﬁguration screens

Recall Safe Mute Group

OVERVIEWINPUT/OUTPUT/TITLE LIST

Allows you to record directly to a

computer or USB storage device, play

back audio ﬁles, manage titles, etc.

SETUP

Used to conﬁgure general mixer settings,

OMNI OUT settings, recall safe settings,

assign user-deﬁned keys and knobs,

conﬁgure custom fader banks, and set up

other preferences.

If a Tio1608-D is connected to the NY64-D,

settings for the Tio1608-D are also

available on this screen.

TF-RACK Quick Guide

Displaying the conﬁguration screens

To return to the OVERVIEW screen, press the Home key ( ) below the display.

The OVERVIEW screen can display the CH STRIP section, the FADER section and the SELECTED CHANNEL section. When the OVERVIEW screen is ﬁrst displayed, the FADER section is displayed.

By default, you

can switch between the FADER section and the CH STRIP section by pressing the Home key ( ) while the OVERVIEW screen is displayed.

In the example shown here, we will explain how to switch to the different screens from the input channel screen. For details or information about other screens, refer to the Reference Manual.

Initial Data

INPUT

Allows you to change input channel settings.

Controls the EQ for each channel.

GATE

Allows you to conﬁgure the noise gate for

each channel.

COMP

Allows you to conﬁgure the compressor

for each channel.

OVERVIEW CH STRIP section

Provides an overall view of the mixer. From here