Draft
L10ax Windows
Regulatory Guide
ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corp., registered in many
jurisdictions worldwide. All other trademarks are the property of their respective owners. © 2022 Zebra
Technologies Corp. and/or its affiliates. All rights reserved.
Zebra Technologies | 3 Overlook Point | Lincolnshire, IL 60069 USA
zebra.com
MN-004356-02EN — 02/22
Regulatory Information
This device is approved under Zebra Technologies Corporation.
This guide applies to the following model numbers:
•RTL10C0
•RTL10C1
All Zebra devices are designed to be compliant with the rules and regulations in
the locations they are sold and will be labeled as required.
Local language translation / Tradução do idioma local / Übersetzung in die lokale
Sprache / Raduccion de idioma local / Traduction en langue locale / Prijevod na
lokalni jezik / Traduzione in lingua locale / 現地語の翻訳 / 현지 언어 번역 /
Перевод на местный язык / 本地語言翻譯 / 本地语言翻译 / Yerel dil çeviri /
Tłumaczenie na język lokalny : zebra.com/support
Any changes or modifications to Zebra equipment not expressly approved by
Zebra could void the user’s authority to operate the equipment.
Operating temperature for handheld use and non-hazardous locations:
-20° to 60° C (-4° to 140° F)
Operating temperature for handheld use and hazardous locations: 5° to 40° C
(41° to 104° F)
Operating temperature with AC power adapter: -20° to 40° C (-4° to 104° F)
Storage temperature: -30° to 70° C (-22° to 158° F)
CAUTION: Only use Zebra approved and NRTL-certified accessories,
battery packs, and battery chargers. Do NOT attempt to charge damp/
wet mobile computers, printers or batteries. All components must be
dry before connecting to an external power source.
Bluetooth® Wireless Technology
This is an approved Bluetooth® product. For more information on the Bluetooth
SIG listing, please visit bluetooth.com.
Regulatory Markings
Regulatory markings subject to certification are applied to the device signifying the
radio(s) is/are approved for use. Refer to the Declaration of Conformity (DoC) for
details of other country markings. The DOC is available at: zebra.com/doc.
The regulatory marks specific to this device (including FCC and ISED) are
available on the screen of the device by following these instructions:
> Zebra Technologies > E-Label
Health and Safety Recommendations
Ergonomic Recommendations
In order to avoid or minimize the potential risk of ergonomic injury, always follow
good ergonomic workplace practices. Consult with your local Health and Safety
Manager to ensure that you are adhering to your company’s safety programs to
prevent employee injury.
Vehicle Installation
RF signals may affect improperly installed or inadequately shielded electronic
systems in motor vehicles (including safety systems). Check with the
manufacturer or its representative regarding your vehicle. Ensure the equipment
is installed to avoid driver distractions. You should also consult the manufacturer
about any equipment that has been added to your vehicle.
Position the device within easy reach. User should be able to access the device
without removing their eyes from the road.
IMPORTANT: Before installing or using, check national and local laws
regarding distracted driving.
Safety on the Road
Give your full attention to driving. Obey the laws and regulations on the use of
wireless devices in the areas where you drive.
The wireless industry reminds you to use your device / phone safely when driving.
Restricted Use Locations
Remember to observe restrictions and obey all signs and instructions on the use
of electronic devices in restricted use locations.
Safety in Hospitals and Aircraft
NOTE: Wireless devices transmit radio frequency energy that may
affect medical electrical equipment and aircraft’s operation. Wireless
devices should be switched off wherever you are requested to do so in
hospitals, clinics, healthcare facilities or by airline staff. These requests
are designed to prevent possible interference with sensitive
equipments.
Medical Devices
It is recommended that a minimum separation distance of 20 cm (8 inches) be
maintained between a wireless device and a medical devices such as
pacemakers, defibrillator, or other implantable devices to avoid potential
interference with the medical device. Pacemaker users should keep the device at
the opposite side of the pacemaker or turn OFF the device if suspected of
interference.
Please consult your physician or the manufacturer of the medical device to
determine if the operation of your wireless product may interfere with the medical
device.
RF Exposure Guidelines
Safety Information
Reducing RF Exposure – Use Properly
Only operate the device in accordance with the instructions supplied.
The device complies with internationally recognized standards covering human
exposure to electromagnetic fields. For information on international human
exposure to electromagnetic fields, refer to the Zebra Declaration of Conformity
(DoC) at zebra.com/doc.
Use only Zebra tested and approved headset, belt-clips, holsters, and similar
accessories to ensure RF exposure compliance. If applicable, follow the
instructions for use as detailed in the accessory guide.
The use of third-party belt clips, holsters, and similar accessories may not comply
with RF exposure compliance requirements and should be avoided.
For further information on the safety of RF energy from wireless devices, refer to
RF exposure and assessment standards section at zebra.com/responsibility.
Handheld or Body-Worn Devices
To satisfy RF exposure requirements, this device must operate with a minimum
separation distance of 0 cm or more from a user's body and nearby persons.
LED Devices
Classified as ‘EXEMPT RISK GROUP’ according to IEC 62471:2006 and
EN 62471:2008.
Pulse Duration: 10 ms or CW (RTL10C0, RTL10C1 with SE4107)
Power Supply
WARNING ELECTRICAL SHOCK: Use only a Zebra approved,
Certified ITE [LPS] power supply with appropriate electrical ratings.
Use of alternative power supply will invalidate any approvals given to
this unit and may be dangerous.
Batteries and Power Packs
This information applies to Zebra-approved batteries and power packs containing
batteries.
Battery Information
CAUTION: Risk of explosion if battery is replaced by an incorrect type.
Dispose of batteries according to instructions.
Use only Zebra approved batteries. Accessories which have battery charging
capability are approved for use with the following battery models:
•Model XLMB1 (7.6 VDC, 4770 mAh)
•Model XLBE1 (7.6 VDC, 13000 mAh)
Zebra approved rechargeable battery packs are designed and constructed to the
highest standards within the industry.
However, there are limitations as to how long a battery can operate or be stored
before needing replacement. Many factors affect the actual life cycle of a battery
pack such as heat, cold, harsh environmental conditions, and severe drops.
When batteries are stored over six months, some irreversible deterioration in
overall battery quality may occur. Store batteries at half charge in a dry, cool
place, removed from the equipment to prevent loss of capacity, rusting of metallic
parts, and electrolyte leakage. When storing batteries for one year or longer, the
charge level should be verified at least once a year and charged to half charge.
Replace the battery when a significant loss of run time is detected.
•Standard warranty period for all Zebra batteries is one year, regardless if the
battery was purchased separately or included as part of the host device. For
more information on Zebra batteries, please visit:
zebra.com/batterydocumentation and select the Battery Best Practices link.
Battery Safety Guidelines
IMPORTANT – SAFETY INSTRUCTIONS – SAVE THESE
INSTRUCTIONS
WARNING – When using this product basic safety precautions should
always be followed, including the following:
The area in which the units are charged should be clear of debris and
combustible materials or chemicals. Particular care should be taken
where the device is charged in a non-commercial environment.
•Read all the instructions before using the product.
•Follow battery usage, storage, and charging guidelines found in the user's
guide.
•Improper battery use may result in a fire, explosion, or other hazard.
•To charge the mobile device battery, the battery and charger temperatures
must be between 0°C and +40°C (+32°F and +104°F).
•Do not use incompatible batteries and chargers. Use of an incompatible battery
or charger may present a risk of fire, explosion, leakage, or other hazard. If you
have any questions about the compatibility of a battery or a charger, contact
Zebra support.
•Do not disassemble or open, crush, bend or deform, puncture, or shred.
Damaged or modified batteries may exhibit unpredictable behavior resulting in
fire, explosion, or risk of injury.
•Severe impact from dropping any battery-operated device on a hard surface
could cause the battery to overheat.
•Do not short circuit a battery or allow metallic or conductive objects to contact
the battery terminals.
•Do not modify, disassemble, or remanufacture, attempt to insert foreign objects
into the battery, immerse or expose to water, rain, snow or other liquids, or
expose to fire, explosion, or other hazard.
•Do not leave or store the equipment in or near areas that might get very hot,
such as in a parked vehicle or near a radiator or other heat source. Do not place
battery into a microwave oven or dryer.
•To reduce the risk of injury, close supervision is necessary when used near
children.
•Please follow local regulations to promptly dispose of used re-chargeable
batteries.
•Do not dispose of batteries in fire. Exposure to temperatures over 100°C
(212°F) may cause explosion.
•Seek medical advice immediately if a battery has been swallowed.
•In the event of a battery leak, do not allow the liquid to come in contact with the
skin or eyes. If contact has been made, wash the affected area with large
amounts of water and seek medical advice.
•If you suspect damage to your equipment or battery, contact Zebra support to
arrange for inspection.
Marking and European Economic Area (EEA)
Statement of Compliance
Zebra hereby declares that this radio equipment is in compliance with Directives
2014/53/EU and 2011/65/EU.
Any radio operation limitations within EEA countries are identified in Appendix A
of EU Declaration of Conformity. The full text of the EU Declaration of Conformity
is available at: zebra.com/doc.
EU Importer : Zebra Technologies B.V
Address: Mercurius 12, 8448 GX Heerenveen, Netherlands
Waste Electrical and Electronic Equipment (WEEE)
For EU and UK Customers: For products at the end of their life, please refer to
recycling/disposal advice at: zebra.com/weee.
United States and Canada Regulatory
Radio Frequency Interference Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received including interference that
may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
rules.These limits are designed to provide reasonable protection
against harmfulb interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Radio Frequency Interference Requirements – Canada
Innovation, Science and Economic Development Canada ICES-003 Compliance
Label: CAN ICES-3 ([B])/NMB-3([B])
This device complies with Innovation, Science and Economic Development
Canada’s licence-exempt RSSs. Operation is subject to the following two
conditions: (1) This device may not cause interference; and (2) This device must
accept any interference, including interference that may cause undesired
operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et Développement économique
Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radio
électrique subi même si le brouillage est susceptible d'en compromettre le
fonctionnement.
This device is restricted to indoor use when operating in the 5150 to 5350 MHz
frequency range.
Lorsqu'il fonctionne dans la plage de fréquences 5 150- 5350 MHz, cet appareil
doit être utilisé exclusivement en extérieur.
RF Exposure Requirements - FCC and ISED
The FCC has granted an Equipment Authorization for this device with all reported
SAR levels evaluated in compliance with the FCC RF emission guidelines. SAR
information on this device is on file with the FCC and can be found under the
Display Grant section of fcc.gov/oet/ea/fccid.
To satisfy RF exposure requirements, this device must operate with a minimum
separation distance of 0 cm or more from a user's body and nearby persons.
Pour satisfaire aux exigences d’exposition aux RF, cet appareil doit fonctionner à
une distance minimale de séparation de 0 cm ou plus du corps de l’utilisateur et
des personnes à proximité.
Hotspot Mode
To satisfy RF exposure requirements in hotspot mode, this device must operate
with a minimum separation distance of 1.0 cm or more from a user’s body and
nearby pesons.
Pour satisfaire aux exigences d’exposition aux RF en mode points d’accès sans
fil, cet appareil doit fonctionner à une distance minimale de 1,0 cm du corps de
l’utilisateur et des personnes à proximité.
Remote and Standalone Antenna Configurations
To comply with FCC/ISED RF exposure requirements, antennas that are mounted
externally at remote locations or operating near users at stand-alone desktop or
similar configurations must operate with a minimum separation distance of 0 cm
from the user or nearby persons.
La conformité aux normes d'exposition RF établies par les organismes FCC/ISED
exige une distance minimale de 0 cm entre l'antenne et l'utilisateur ou toute
personne à proximité lorsque celle-ci est installée à l'extérieur ou lorsqu'elle est
placée sur un bureau ou dans une configuration similaire.
Co-located Statement
To comply with FCC RF exposure compliance requirement, the antenna used for
this transmitter must not be co-located (within 20 cm) or operating in conjunction
with any other transmitter/antenna except those already approved in this filling.
Hotspot ISED Notice
When operating in hotspot mode, this device is restricted to indoor use when
operating in the 5150 -5350 MHz frequency range.
En mode de connexion partagée (hotspot), l'utilisation de cet appareil doit se faire
exclusivement en extérieur lorsqu'il fonctionne dans la plage de fréquences
5 150 -5 350 MHz.
The maximum antenna gain permitted for devices in the bands 5250 -5350 MHz,
5470 -5725 MHz and 5725 -5850 MHz shall be such that the equipment still
complies with the Effective Isotropic Radiated Power (EIRP) limit.
Le gain maximal d'antenne autorisé pour les appareils fonctionnant dans les
bandes de fréquences 5 250 -5 350 MHz, 5 470 -5 725 MHz et
5 725 -5 850 MHz doit être tel que l’équipement respecte toujours la limite de
puissance isotrope rayonnée équivalente (PIRE).
MN-004356-02ENa_l10ax-windows-rg-en.fm Page 1
Draft
UL Listed Products with GPS
Underwriters Laboratories Inc. (UL) has not tested the performance or reliability of
the Global Positioning System (GPS) hardware, operating software, or other
aspects of this product. UL has only tested for fire, shock, or casualties as outlined
in UL’s Standard(s) for Safety for Information Technology Equipment. UL
Certification does not cover the performance or reliability of the GPS hardware
and GPS operating software. UL makes no representations, warranties, or
certifications whatsoever regarding the performance or reliability of any GPS
related functions of this product.
Marquage UL des produits équipés d'un GPS
Les tests menés par Underwriters Laboratories Inc. (UL) ne portent ni sur les
performances, ni sur la fiabilité du matériel et du logiciel d'exploitation du GPS
(Global Positioning System), ni sur tout autre aspect de ce produit. UL a
uniquement testé la résistance au feu, aux chocs et aux sinistres, comme le
définit la norme UL60950-1 relative à la sécurité des matériels de traitement de
l'information. La certification UL ne couvre ni les performances, ni la fiabilité du
matériel et du logiciel d'exploitation GPS. UL ne formule aucune déclaration, ni ne
délivre aucune garantie ni aucun certificat concernant les performances et la
fiabilité des fonctions GPS de ce produit.
Hazardous Locations
Class 1 Div 2 Product Regulatory Information
The following regulatory statements apply only to the Class 1 Div 2 products. The
Class 1 Div 2 products are marked UL Listed 3JDT.
Installation and Operating Instructions
An installation manual shall be provided with each unit to direct the user on proper
installation and operation of the device.
The warning and caution marking should be provided in English and French for
Canadian Certification.
1. SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B, C AND D
HAZARDOUS LOCATIONS, OR NONHAZARDOUS LOCATIONS ONLY.
2. WARNING - EXPLOSION HAZARD - External Connections (Audio port, USB
ports, USB type-C port, HDMI port, Docking Connectors, Antenna pass-through
ports and optional RS-232 port) are not to be used in a Hazardous Location.
3. WARNING - EXPLOSION HAZARD - Tablet PC is to be only powered from the
battery pack while in Hazardous Locations. Power adapter is not certified to use in
Hazardous Locations and not to be used in Hazardous Locations.
4. WARNING - EXPLOSION HAZARD – BATTERY MUST ONLY BE CHANGED/
CHARGED IN AN AREA KNOWN TO BE NON-HAZARDOUS.
5. WARNING – EXPLOSION HAZARD. Micro SD card slot, SIM card slot, Battery
Pack, DO NOT REMOVE OR REPLACE WHILE CIRCUIT IS LIVE UNLESS THE
AREA IS FREE OF IGNITIBLE CONCENTRATIONS.
Informations réglementaires sur les produits de classe 1, division 2
Les déclarations réglementaires suivantes ne s'appliquent qu'aux produits de
classe 1, division 2. Les produits Class 1 Div 2 sont marqués UL Listed 3JDT.
Instructions d’installation et d’utilisation
Un manuel d’installation est fourni avec chaque appareil pour aider l’utilisateur à
bien l’installer et l’utiliser.
Les symboles de mise en garde et d’avertissement doivent être indiqués en
anglais et en français pour être conformes à la certification canadienne.
1. CONVIENT À UNE UTILISATION DANS LES EMPLACEMENTS
DANGEREUX DE CLASSE I, DIVISION 2, GROUPES A, B, C ET D, OU DANS
LES EMPLACEMENTS NON DANGEREUX SEULEMENT.
2. AVERTISSEMENT – RISQUE D’EXPLOSION – les connexions externes (port
audio, ports USB, port USB de type C, port HDMI, connecteurs de station
d’accueil, ports d’antenne passe-système et port RS-232 facultatifs) ne doivent
pas être utilisées dans un emplacement dangereux.
3. AVERTISSEMENT – RISQUE D’EXPLOSION – la tablette électronique doit
être uniquement alimentée à partir des blocs-batteries lorsqu’elle est utilisée
dans un emplacement dangereux. L’adaptateur d’alimentation n’est pas certifié
pour une utilisation dans les emplacements dangereux et ne doit pas être utilisé
dans les emplacements dangereux.
4. AVERTISSEMENT – RISQUE D’EXPLOSION – LA BATTERIE DOIT ÊTRE
REMPLACÉE OU CHARGÉE UNIQUEMENT DANS UN ENDROIT JUGÉ NON
DANGEREUX.
5. AVERTISSEMENT – RISQUE D’EXPLOSION. Fente pour carte Micro SD,
fente pour carte SIM, bloc-batteries, NE PAS RETIRER OU REMPLACER
PENDANT QUE LE CIRCUIT EST ACTIVÉ, À MOINS QUE LA ZONE NE SOIT
EXEMPTE DE SOURCES INFLAMMABLES.
中国
通过访问以下网址可下载当地语言支持的产品说明书 zebra.com/support
确认进网标贴和证书真伪可查询网址 : tenaa.com.cn/.
锂电池安全警示语 :
警告：请勿拆装，短路，撞击，挤压或者投入火中
注意：如果电池被不正确型号替换，或出现鼓胀，会存在爆炸及其他危
险
请按说明处置使用过的电池
电池浸水后严禁使用
如果配套使用外部电源适配器，请确保其已通过 CCC 认证
（一） 符合 “ 微功率短距离无线电发射设备目录和技术要求 ” 的具体条款和使用场
景，采用的天线类型和性能，控制、调整及开关等使用方法；
（二）不得擅自改变使用场景或使用条件、扩大发射频率范围、加大发射功率 （包
括额 外加装射频功率放大器），不得擅自更改发射天线；
（三）不得对其他合法的无线电台 （站）产生有害干扰，也不得提出免受有害干扰
保护；
（四）应当承受辐射射频能量的工业、科学及医疗 （ISM）应用设备的干扰或其他
合法的无线电台 （站）干扰；
（五）如对其他合法的无线电台 （站）产生有害干扰时，应立即停止使用，并采取
措施消除干扰后方可继续使用；
（六）在航空器内和依据法律法规、国家有关规定、标准划设的射电天文台、气象
雷达站、卫星地球站 （含测控、测距、接收、导航站）等军民用无线电台 （站）、
机场等的电磁环境保护区域内使用微功率设备，应当遵守电磁环境保护及相关行业
主管部门的规定；
（七）禁止在以机场跑道中心点为圆心、半径 5000 米的区域内使用各类模型遥控
器；
（八）有关支持的工作环境条件，请参阅本指南的最高工作温度以及电池信息和电
源信息部分。
产品中有害物质的名称及含量
Colombia
Señor usuario, la siguiente información se entrega de conformidad con lo
establecido en el Régimen de protección de los derechos de los usuarios,
expedido por la Comisión de Regulación de Comunicaciones.
Recomendaciones de uso:
1. Utilice siempre que pueda dispositivos manos libres.
2. Evite utilizar el equipo mientras conduce un vehículo.
3. En caso que el teléfono sea utilizado por niños, ancianos, mujeres
embarazadas y población inmunocomprometida, consulte a su médico y el
manual del equipo.
4. Si usted utiliza algún dispositivo electrónico de uso médico, asegúrese que el
mismo esté protegido contra las ondas de radiofrecuencia externas.
5. Apague su teléfono en lugares tales como: hospitales, centros de salud,
aviones, estaciones de suministro de combustible, en presencia de gases
explosivos y lugares donde se realizan explosiones.
6. Evite que terceros hagan uso de su teléfono para prevenir la implantación de
dispositivos como programas espías (spyware) o identificadores ocultos, que
atentan contra la seguridad de la información contenida en el mismo.
Евразийский Таможенный Союз (EAC)
Данный продукт соответствует требованиям знака EAC.
France
Cet appareil a été testé et déclaré conforme aux limites applicables d'exposition
aux radiofréquences (RF).
Le débit d'absorption spécifique (DAS) local quantifie l'exposition de l'utilisateur
aux ondes électromagnétiques de l'équipement concerné.
Les valeurs DAS les plus élevées sont disponibles sur la déclaration de
conformité (DoC) disponible sur: zebra.com/doc.
México
La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es
posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este
equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que
pueda causar su operación no deseada.
臺灣
低功率電波輻射性電機管理辦法
取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更
頻率、加大功率或變更原設計之特性及功能。
低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，
應立即停用，並改善至無干擾時方得繼續使用。
前述合法通信，指依電信管理法規定作業之無線電通信。低功率射頻器材須忍受合
法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
應避免影響附近雷達系統之操作
公司資訊
台灣斑馬科技股份有限公司 / 台北市信義區松高路 9 號 13 樓
行政院環保署 (EPA) 要求乾電池製造或進口商，需依廢棄
物清理法第 15 條之規定，於販售、贈送或促銷的電池上
標示回收標誌。請聯絡合格的台灣回收廠商，以正確棄置
電池。
限用物質含有情況標示聲明書
TÜRK WEEE Uyumluluk Beyanı
EEE Yönetmeliğine Uygundur.
ประเทศไทย
เครื่ องโทรคมนาคมและอุ ปกรณ์ นี้ มี ความสอดคล้ องตามข้ อกำหนดของ กทช .
เครื่องวิทยุคมนาคมนี้มีอัตราการดูดกลืนพลังงานจําเพาะ (Specific Absorption Rate –
SAR) อั นเนื่ องมาจากเครื่ องวิ ทยุ คมนาคมเท่ ากั บ
•RTL10C0 1.595 w/kg
•RTL10C1 1.595 w/kg
ซึ่งสอดคล้องตามมาตรฐานความปลอดภัยต่อสุขภาพของมนุษย์จากการใช้เครื่องวิทยุคมนา
คมที่ คณะกรรมการกิ จการโทรคมนาคมแห่ งชาติ ประกาศกํ าหนด
United Kingdom
Statement of Compliance
Zebra hereby declares that this radio equipment is in
compliance with the Radio Equipment Regulations 2017 and the
Restriction of the Use of Certain Hazardous Substances in
Electrical and Electronic Equipment Regulations 2012.
Any radio operation limitations within UK are identified in Appendix A of UK
Declaration of Conformity.
The full text of the UK Declaration of Conformity is available at: zebra.com/doc.
UK Importer: Zebra Technologies Europe Limited
Address: Dukes Meadow, Millboard Rd, Bourne End, Buckinghamshire, SL8 5XF
Warranty
For the complete Zebra hardware product warranty statement, go to:
zebra.com\warranty.
Service Information
Before you use the unit, it must be configured to operate in your facility's network
and run your applications.
If you have a problem running your unit or using your equipment, contact your
facility's Technical or System Support. If there is a problem with the equipment,
they will contact Zebra support at zebra.com/support.
For the latest version of the guide go to: zebra.com\support.
Software Support
Zebra wants to ensure that customers have the latest entitled software at the time
of device purchase in order to keep the device operating at peak performance
levels. To confirm that your Zebra device has the latest entitled software available
at the time of purchase, go to zebra.com/support.
Check for the latest software from Support > Products, or search for the device
and select Support > Software Downloads.
If your device does not have the latest entitled software as of your device
purchase date, e-mail Zebra at [email protected] and ensure you
include the following essential device information:
•Model number
•Serial number
•Proof of purchase
•Title of the software download you are requesting.
If it is determined by Zebra that your device is entitled to the latest version of
software, as of the date you purchased your device, you will receive an e-mail
containing a link directing you to a Zebra Web site to download the appropriate
software.
Product Support Information
•For information on using this product, see the User Guide at zebra.com/l10ax.
•To find quick answers to known product behaviors, access our knowledge
articles at supportcommunity.zebra.com/s/knowledge-base.
•Ask your questions in our Support community at supportcommunity.zebra.com.
•Download product manuals, drivers, software, and view how-to videos at
zebra.com/support.
•To request a repair for your product, go to zebra.com/repair.
部件名称 (Parts)
有害物质
铅
(Pb) 汞
(Hg) 镉
(Cd) 六价铬
(Cr(VI))
多溴
联苯
(PBB)
多溴二
苯醚
(PBDE)
金属部件 (Metal
Parts) X O O O O O
电路模块 (Circuit
Modules) X O O O O O
电缆及电缆组件
(Cables and Cable
Assemblies)
O O O O O O
塑料和聚合物部件
(Plastic and
Polymeric Parts)
O O O O O O
光学和光学组件
(Optics and Optical
Components)
O O O O O O
电池 (Batteries) O O O O O O
外部电源 (Ext. Pwr
Sply) O O O O O O
本表格依据 SJ/T 11364 的规定编制。
O: 表示该有害物质在该部件所有均质材料中的含量均在SJ/T 11364--2014
规定的限量要求以下。
X: 表示该有害物质至少在该部件的某一均质材料中的含量超 SJ/T 11364--
2014 规定的限量要求。( 企业可在此处，根据实际情况对上表中打 “×” 的技术
原因进行进一步说明。
設備名稱 : 平板電腦 型號 （型式）: RTL10C0,
RTL10C1
單元 Unit
限用物質及其化學符號
Restricted substances and its chemical symbols
鉛
(Pb 汞
(Hg 鎘
(Cd 六價
鉻多溴
聯苯 多溴二
苯醚
印刷電路板及電子組件 − O O O O O
金屬零件 O O O O O O
電纜及電纜組件 O O O O O O
塑料和聚合物零件 O O O O O O
光學與光學元件— O O O O O O
備考 1. 〝超出 0.1 wt % 〞及〝超出 0.01 wt % 〞係指限用物質之百
分比含量超出百分比含量基準值。
備考 2. 〝 O 〞係指該項限用物質之百分比含量未超出百分比含量基
準值。
備考 3. 〝−〞係指該項限用物質為排除項目。
Note 1: “Exceeding 0.1 wt%” and “exceeding 0.01 wt%” indicate that
the percentage content of the restricted substance exceeds the
reference percentage value of presence condition.
Note 2: “O” indicates that the percentage content of the restricted
substance does not exceed the percentage of reference value of
presence.
Note 3: The “ − ” indicates that the restricted substance corresponds
to the exemption.
MN-004356-02ENa_l10ax-windows-rg-en.fm Page 2
-
1
-
2
dans d''autres langues
- English: Zebra L10ax User guide
Documents connexes
-
Zebra ZE511/ZE521 Le manuel du propriétaire
-
-
Zebra MC33 Mode d'emploi
-
Zebra MC2700 Mobile Computer Mode d'emploi
-
-
Zebra TC5301 Mode d'emploi
-
-
-
-
