OKIN RF402A Manuel utilisateur

Taper
Manuel utilisateur
Issue Department
Bedding Division
Date
2022-07-19
Author
User Manual
Edition
1.1
Page 1 of 4
RF402A
Figure 1 button ofremote
1 / 4
Issue Department
Bedding Division
Date
2022-07-19
Author
User Manual
Edition
1.1
Page 2 of 4
Item
1.1 Head up
Press and hold HEAD UP button of remote, the control box receives the
signal and controls the head motor through the linehead motor moves
out, stop when released
1.2 Head down
Press and hold HEAD DOWN button of remote, the control box receives the signal and
controls the head motor through the line,head motor moves in, stop when released
2 / 4
Product name:Remote Control
Model name:RF402A
Frequency Range:2403-2480MHz
Antenna Specification:PCB Antenna/1dBi
Power supply:3Vdc
COMPONENTS
1.Head up
2.Head down
Description
Issue Department
Bedding Division
Date
2022-07-19
Author
User Manual
Edition
1.1
Page 3 of 4
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
3 / 4
Federal Communications Commission (FCC) Statement
You are cautioned that changes or modifications not expressly approved by the part responsible
for compliance could void the users authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received, including interference that may cause
undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
RF warning for Portable device:
The device has been evaluated to meet general RF exposure requirment. The device can be
used in portable exposure condition without restriction.
Issue DepartmentBedding Division Date 2022-07-19
Author
User Manual Edition 1.1
Page 4of 4
Canada, Industry Canada (IC) Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radio
exempts de licence.L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage adioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
4 / 4
ISED RF exposure statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment.The device has been evaluated to meet general RF exposure requirement.
Le matériel est conforme aux limites de dose d'exposition aux rayonnements énoncés pour fac
un autre environnement.ce dispositif a été évalué à satisfaire l'exigence générale de
l'exposition aux rf.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

OKIN RF402A Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues

Documents connexes