KEESON MC232SC Manuel utilisateur

MC232SC
Marque
KEESON
Modèle
MC232SC
Taper
Manuel utilisateur
Issue department：Bedding Division
Date：
2017-05-03
Product Function
instruction
Author：
Ben
No：MC232SC
MC232SC
Version：
1.0
Page 1 of 6
1
MC232SC Function instruction
1. Electrical configuration diagram：
Issue department：Bedding Division
Date：
2017-05-03
Product Function
instruction
Author：
Ben
No：MC232SC
MC232SC
Version：
1.0
Page 2 of 6
2
2. Function Picture
1. Process of test
1.1. HEAD port
Connect to head actuator,control by remote single:
Click head up button on the remote, head actuator moves out, stop when released；
Issue department：Bedding Division
Date：
2017-05-03
Product Function
instruction
Author：
Ben
No：MC232SC
MC232SC
Version：
1.0
Page 3 of 6
3
Click head down button，head actuator moves in, stop when released；
This function takes effect only by pressing the corresponding button on the remote.
1.2. FOOT port
Connect to foot actuator,control by remote single:
Click foot up button，foot actuator moves out，stop when released；
Click foot down button，foot actuator moves in，stop when released；
This function takes effect only by pressing the corresponding button on the remote.
1.3. LUMBAR port
Connect to lumbar actuator,control by remote single:
Click lumbar up button，lumbar actuator moves out，stop when released；
Click lumbar down button，lumbar actuator moves in，stop when released；
This function takes effect only by pressing the corresponding button on the remote.
1.4. FOOT VIBRATION
Connect to foot massage,control by remote:
Click foot massage + button,foot massage strengthens by one level;
Click foot massage - button,foot massage weakenby one level;
This function takes effect only by pressing the corresponding button on the remote.
1.5. HEAD VIBRATION
Connect to head massage,control by remote:
Click head massage + button,head massage strengthens by one level;
Click head massage - button,head massage weakenby one level;
This function takes effect only by pressing the corresponding button on the remote.
1.6. MULTIFUNCTION port
Connect with the same other Control box or Other accessories;
Issue department：Bedding Division
Date：
2017-05-03
Product Function
instruction
Author：
Ben
No：MC232SC
MC232SC
Version：
1.0
Page 4 of 6
4
1.7. Power LED & PAIRING LED
Power supply for control box, LED of control box flashes for 10 seconds,and then turns on。
1.8. Power
Connect to the 29V DC;
1.9. Sonic signals input port
Insert the acoustic signal provided by the sound system.
1.10. Pair Function
Power on，the control box enters into mode of code paring；
Press and hold the paring LED of Remote, the backlight of paring LED flashes, the backlight of remote flashes, the
remote enters into mode of code paring;
The backlight of paring LED of remote stops flashing, and the paring led of control box turns off, it indicates that
the code paring is successful;
If fails, repeat all the processes above;
1.11. Test for underbed light
Click button of underbed light, turns on( or turns off ) the underbed light, switch the status once when click once；
This function takes effect only by pressing the corresponding button on the remote.
1.12. FLAT function
Press and release the FLAT button on remote，the head and foot actuators moves to lower position(when the
actuator is free, can turn off the vibration motor and turn off the indicator light when press once )，stop when
press any buton；
This function takes effect only by pressing the corresponding button on the remote.
Issue department：Bedding Division
Date：
2017-05-03
Product Function
instruction
Author：
Ben
No：MC232SC
MC232SC
Version：
1.0
Page 5 of 6
5
1.13. ZERO G position function
Press and release ZERO G button on remote，the head and foot actuator moves to preset memory position，stop
when press any button；
This function takes effect only by pressing the corresponding button on the remote.
1.14. LOUNGE position function
Press and release LOUNGE on remote，the head and foot actuator moves to preset memory
position, stop when press any button；
This function takes effect only by pressing the corresponding button on the remote.
1.15. TV position function
Press and release TV on remote，the head and foot actuator moves to preset memory position,
stop when press any button；
This function takes effect only by pressing the corresponding button on the remote.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this de
vice may not cause harmful interference, and (2) this device must accept any interference received, including in
terference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s aut
hority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not insta
lled and used in accordance with the instructions, may cause harmful interference to radio communications. Howe
ver, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Issue department：Bedding Division
Date：
2017-05-03
Product Function
instruction
Author：
Ben
No：MC232SC
MC232SC
Version：
1.0
Page 6 of 6
6
• Consult the dealer or an experienced radio/TV technician for help.
Important Note:
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
ISED Statement
- English: This device complies with Industry Canada license‐exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This d
evice must accept any interference, including interference that may cause undesired operation of the device.
The digital apparatus complies with Canadian CAN ICES‐3 (B)/NMB‐3(B).
‐ French: Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitationestautorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produ
ire de brouillage, et (2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le brouill
ageest susceptible d'encompromettre le fonctionnement.
This radio transmitter (ISED certification number: 22406-MC232SC) has been approved by Industry Canada to
operate with the antenna types listed with the maximum permissible gain indicated. Antenna types not included
in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with
this device.
Le présent émetteur radio (ISED certification number: 22406-MC232SC) a été approuvé par Industrie Canada pour
fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types
d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué, sont strictement
interdits pour l'exploitation de l'émetteur.
Radiation Exposure Statement
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

KEESON MC232SC Manuel utilisateur

MC232SC
Marque
KEESON
Modèle
MC232SC
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents