Chief PCM2000B Guide d'installation
- Catégorie
- Mur
- Taper
- Guide d'installation
PCM Series Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® and ClickConnect™ are registered trademarks of
Milestone AV Technologies. All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for the installation of this kit can result in serious personal
injury or damage to equipment! It is the installer’s
responsibility to make sure the structure to which this mount
is attached can support five times the combined weight of all
equipment.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to this mount does not exceed
200 lbs (91 kg).
•The weight capacity of the PCM2000 may be LIMITED
to the lowest weight capacity of any other component
located between the PCM2000 and the supporting
structure.
WARNING:
The installer is responsible for verifying that the
Listed fixture (coupler or ceiling plate - not included) has 1 1/2”
NPT or NPSM threads following ANSI/ASME B1.20.1, and is
capable of supporting the maximum weight capacity of the
PCM2000 as stated previously.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
NOTE: The PCM Series includes:
•Accessory Model PCM2000B (to be used with Listed
Chief accessory PSBU interface bracket--not
included).
--SAVE THESE INSTRUCTIONS--
Installation Instructions PCM Series
3
LEGEND
TOOLS REQUIRED FOR INSTALLATION
PARTS
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
3/16” (provided)
9/16"
B (1)
C (1)
D (6)
A (1)
[Column assembly]
[Faceplate]
3/16”
5/16-18 x 1/2”
PCM Series Installation Instructions
4
DIMENSIONS
19.2 5
4.09 1.07
3.36
FACE TILTS
5UP
25 DOWN
150°
16.39
7.00
5.00
VERTICAL
ADJUSTMENT
APPROXIMATE
MALE
1.5" NPT
CENTER OF DISPLAY
TOP MOUNTING BUTTON ON
PSB-XXXX DRAWING GOES HERE
8.02
8.14
26.42 MIN.
OF DISPLAY
TO
APPROX. CENTER
11.10 MIN.
31.41 MAX.
16.10 MAX.
7.61
.78
15.6 3
MAX DISPLAY HEIGHT: 38.5"
NOTE:
PSBU INTERFACE BRACKET
NOT SHOWN. THE PSBU INTERFACE
BRACKET WILL ADD 1” IN DEPTH
AND MAY AFFECT LOCATION OF
THE DISPLAY ON THE MOUNT.
DIMENSIONS: INCHES
Installation Instructions PCM Series
5
Mount Assembly and Installation
IMPORTANT ! : These installation instructions assume
that the Listed fixture (coupler or ceiling plate - not
included) has 1 1/2” NPT or NPSM threads following
ANSI/ASME B1.20.1, and has been properly installed
and is in place.
1. Fold column out until column mounting bracket rests
against faceplate mounting bracket. (See Figure 1)
2. Secure column against faceplate mounting bracket using
3/16” hex wrench (C) and two 5/16-18 x 1/2” button head
cap screws (D). (See Figure 1)
3. Tighten all hardware.
Figure 1
4. Thread the column assembly (A) into fixture (coupler or
ceiling plate - not included), with a minimum of four threads
engaged.
5. Secure faceplate (B) to faceplate mounting bracket using
3/16” hex wrench (C) and four 5/16-18 x 1/2” button head
cap screws (D). (See Figure 2)
Figure 2
Display Installation
1. Attach PSBU interface bracket (not included) to the display
following instructions included with the interface bracket.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT. Displays can weigh in
excess of 40 lbs (18.1kg). ALWAYS use two people and
proper lifting techniques when installing display.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT. Make sure mounting buttons
on display are properly seated in mounting holes in faceplate.
2. While supporting both sides of display, align four mounting
buttons on interface bracket with four mounting holes in
faceplate. (See Figure 3)
3. Lower display into place listening for audible “click” to ensure
recessed area of mounting buttons are properly seated in
lower area of mounting holes, and “click lock” mechanism
has engaged. (See Figure 3) and (See Figure 4)
Figure 3
1
(D) x 2
2
Faceplate mounting
bracket Column
5
(D) x4
(B) (A)
2
1
PCM Series Installation Instructions
6
NOTE: Holes are provided in the faceplate for use with a
padlock or similar locking device, if desired. In addition,
the pin and nut may be removed from the upper holes
and moved to the lower holes for use as a more
permanent locking device. (See Figure 4)
Figure 4
Adjustments
The PCM is designed to accommodate 5" of display height
adjustment, 4º right and left display roll adjustment, and 15º
down/5º up display pitch (Tilt) adjustment.
Remove display before performing adjustments.
Display Height Adjustment
To adjust display height:
1. Loosen four 5/16-18 button head cap screws using 3/16”
hex wrench (C). (See Figure 5)
2. Adjust faceplate to desired position. (See Figure 5)
3. Tighten four 5/16-18 button head cap screws using 3/16”
hex wrench (C). (See Figure 5)
Figure 5
Display Roll Adjustment
To adjust display roll:
1. Loosen 3/8-16 Nylock nut. (See Figure 6)
2. Adjust faceplate to desired position. (See Figure 6)
3. Tighten 3/8-16 Nylock nut. (See Figure 6)
Figure 6
2
1
A padlock or bolt may
be placed through latch holes
To use as a
more permanent
lock, remove pin
and nuts and move
to lower holes
3
1
2
3
1
2
Installation Instructions PCM Series
7
Display Pitch (Tilt) Adjustment
To adjust display pitch:
1. Loosen four 5/16-18 button head cap screws.
(See Figure 7)
2. Adjust to desired tilt position. (See Figure 7)
3. Tighten four 5/16-18 button head cap screws.
(See Figure 7)
Figure 7
3
1
2
PCM Series Installation Instructions
Chief, a products division of
Milestone AV Technologies
8800-002595 Rev00
2014 Milestone AV Technologies
www.chiefmfg.com
05/14
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Chief PCM2000B Guide d'installation
- Catégorie
- Mur
- Taper
- Guide d'installation
dans d''autres langues
- English: Chief PCM2000B Installation guide
Documents connexes
-
Chief PACTP1 Guide d'installation
-
Chief PDC2306 Guide d'installation
-
-
Chief PSS2000 Guide d'installation
-
-
Chief LCM1U Guide d'installation
-
-
Chief XCB1U Guide d'installation
-
-