Elettrobar 570180 Manuel utilisateur

INSTRUCTION MANUAL FOR DISHWASHERS

BEDIENUNGSANLEITUNG FÜR

GESCHIRRSPÜLMASCHINE

MANUEL D’EMPLOI DU LAVE-VAISSELLE

HANDLEIDING VOOR AFWASMACHINES

Art.no.:

570.035 / 570.040

570.050 / 570.051 / 570.055 / 570.056

570.180

INSTRUCTION MANUAL FOR DISHWASHERS

Page 1 of 14

UK

TRANSLATION FROM THE ORIGINAL INSTRUCTIONS

CONTENTS

CHAP 1 RISKS AND IMPORTANT WARNINGS ...................................................................... 2

1.1 NORMAL OPERATING CONDITIONS ...................................................................................... 3

CHAP 2 PREFACE ................................................................................................................... 4

CHAP 3 INSTALLATION .......................................................................................................... 4

3.1 UNPACKING ...................................................................................................................... 4

3.2 POSITIONING ..................................................................................................................... 4

3.3 ELECTRICAL CONNECTION .................................................................................................. 5

3.4 WATER CIRCUIT HOOKUP ................................................................................................... 6

3.5 CONNECTION TO THE DRAIN LINE ........................................................................................ 6

3.6 RINSE AID AND DETERGENT ................................................................................................ 6

CHAP 4 USING THE MACHINE................................................................................................ 7

4.1 KEY AND SYMBOLS ............................................................................................................ 7

4.2 SWITCHING THE DISHWASHER ON ....................................................................................... 7

4.3 FILLING THE RACK ............................................................................................................. 7

4.4 CYCLE SELECTION AND START-UP ...................................................................................... 7

4.4.1 Under-counter dishwashers ............................................................................... 7

4.4.2 Hood dishwashers ............................................................................................. 8

4.5 PROGRAMMES .................................................................................................................. 8

4.6 REMOVING THE INTEGRAL FILTER ....................................................................................... 8

4.7 EMPTYING THE DISHWASHER .............................................................................................. 8

4.7.1 Appliances with no drain pump .......................................................................... 8

4.7.2 Appliances with drain cycle (*optional) ............................................................... 8

4.8 RESIN REGENERATION (*OPTIONAL) .................................................................................... 9

4.9 LIST OF VIEWABLE MESSAGES ............................................................................................ 9

4.10 END OF SHIFT.................................................................................................................... 9

CHAP 5 MAINTENANCE ........................................................................................................ 10

5.1 GENERAL RULES ............................................................................................................. 10

5.2 CLEANING ....................................................................................................................... 10

5.3 CLEANING THE FILTER UNIT .............................................................................................. 10

5.4 CLEANING THE ARMS ....................................................................................................... 10

CHAP 6 SELF DIAGNOSTICS ................................................................................................ 11

CHAP 7 SETTINGS................................................................................................................. 12

CHAP 8 SCRAPPING ............................................................................................................. 12

CHAP 9 ENVIRONMENT ........................................................................................................ 13

In legal terms, the manufacturer reserves the property of this document. It is forbidden to reproduce it or divulge it with any means

without prior written authorisation.

The manufacturer reserves the right to introduce changes in order to achieve the improvements it deems necessary without prior notice.

442470 MD REV02 26-10-2020 U UK

INSTRUCTION MANUAL FOR DISHWASHERS

Page 2 of 14

UK

Read the instruction manual carefully before starting the machine. The

warnings contained in the manual provide important information on safety and

installation, use and maintenance. Failure to observe the instructions in the

enclosed documentation may compromise the safety of the appliance and

immediately voids the warranty.

Chap 1 RISKS AND IMPORTANT WARNINGS

 This appliance is intended solely for the use for which it was designed. Any

other use is improper and therefore hazardous.

 The specialised technician responsible for installing the appliance must

instruct the user on its operation and any attendant safety measures,

including practical demonstrations.

 Only the manufacturer or an authorised service centre with qualified staff may

work on the machine, even in case of malfunction, using only original spare

parts.

 Always disconnect or isolate the machine from its power and water supplies

before servicing, repairing or cleaning it.

 The machine may NOT be used by persons untrained in its use.

 The appliance may be used by children aged at least 8 years old or persons

with reduced physical, sensory or mental capacities, or with no experience or

knowledge, provided they are supervised or after they have received training

in the safe use of the appliance.

 Children must not play with the appliance.

 Cleaning and maintenance by the user must not be performed by

unsupervised children.

 The machine must NOT be kept powered up when not in use.

 If the machine is not fitted with a plug or other device for completely

disconnecting all contacts, these disconnection devices must be incorporated

in the power supply, in compliance with the installation rules.

 If the power cable is damaged, it must be replaced by the manufacturer or an

authorised technical assistance service, or in any case by a person with

similar qualifications, to prevent all associated risks.

 The screw on the appliance marked with the IEC 60417 standard symbol

5021 represents the equipotential connection.

 NEVER open the machine quickly if it has not completed its cycle.

 NEVER use the machine with the guards installed by the manufacturer

removed.

 NEVER use the machine to wash objects of any form, size or material not

guaranteed to be machine-washable or not in good condition.

 NEVER use the machine or any of its assemblies as steps or support for

persons, property or animals.

 NEVER overload the open door of front-loading machines, which is rated only

to support the basket loaded with dishes.

 NEVER place your bare hands in the wash solution.

INSTRUCTION MANUAL FOR DISHWASHERS

Page 3 of 14

UK

 NEVER overturn the machine after it has been installed.

 If you notice any malfunction or fluid leak, immediately disconnect the power

supply and shut off the water supply.

 Do not install the dishwasher in the vicinity of heat sources over 50°C.

 NEVER leave the dishwasher exposed to the weather (rain, direct sunlight,

etc.)

 The dishwasher may not be installed outdoors without proper cover.

 Never start a wash programme without the overflow in the tub, as applicable.

 Never place magnetic objects in the vicinity of the machine.

 Do not use the top of the machine as a table or support.

 The installer is responsible for checking that the grounding system is fully

operational.

 At the end of testing, the installer must issue a written declaration stating that

the machine has been installed and tested in accordance with established

legislation and good practice.

 DO NOT change the position or tamper with the elements of the machine, as

this could compromise the machine safety.

 Noise pressure level according to EN ISO 4871

o LpA Max = 55db Kpa=2.5db for undercounter versions

o LpA Max = 65db Kpa=2.5db for hood versions

o LpA Max = 76db Kpa=1.5db for utensil washer versions

 Max inlet water temperature: 50°C

 Max inlet water pressure: 4bar (400kPa)

 Appliance designed for permanent connection to the water supply

 Do not clean the appliance with steam or water jets.

 Max loading height

o On the ground in the versions with overflow

o Maximum height 1 m in versions with discharge pump

1.1 Normal operating conditions

Ambient temperature: 40°Cmax /4°Cmin (average 30°C)

Altitude : up to 2000 metres

Relative humidity : Max 30% at 40°C / max 90% at 20°C

INSTRUCTION MANUAL FOR DISHWASHERS

Page 4 of 14

UK

Chap 2 PREFACE

Warnings:

Keep all documentation in the vicinity of the appliance; make it available to the technicians and

operators charged with operating it and keep it in good condition in a safe place, along with

extra copies for frequent reference

The operator must read, understand and familiarise himself with the contents of this

manual before working on or with the appliance.

The appliance is intended solely for professional heavy duty dishwashing applications and must

be installed, operated and serviced only by qualified persons according to the manufacturer's

instructions.

Warranty:

The manufacturer is not liable for any damage or injury resulting from failure to observe the

instructions or improper use of the machine

Failure to observe the instructions in the enclosed documentation may compromise the safety of

the appliance and immediately voids the warranty

Installation and repair by unauthorised technicians and the use non-original spare parts

immediately void the warranty.

Storage:

Transport and storage: -10°C to 55°C with peaks up to 70°C (for no longer than 24 hours)

Chap 3 INSTALLATION

Proper installation is essential to the good operation of the appliance. Some of the data required for

installation of the appliance are given on the nameplate on its RH body panel, and a copy is included

on the cover page of this manual.

The appliance may only be installed by qualified persons authorised to do so.

For Australia and New Zealand this machine must be installed in accordance with

AS/NZS3500.1

3.1 Unpacking

Check the condition of the packaging, and note any evident damage on the shipping bill. Remove the

packaging and check that the appliance is in good condition; immediately report any damage to the

reseller and the shipping agent by fax or registered letter with return receipt. If the damage is such as to

compromise the safety of the appliance, do not install or operate it until it has been inspected by a

qualified technician.

The packaging (plastic bags, expanded polystyrene, nails, etc. ) are hazardous and

must not be left within the reach of children or pets.

3.2 Positioning

 Check that there are no objects or materials in the installation area which may

be damaged by the steam emitted by the appliance during operation, or if there

are, make sure they are properly protected.

 Before positioning the appliance, set up the electrical power supply, water

supply and drain connections.

 For flush-mounting single panel machines, leave a space of at least 10 mm

between the machine walls and the adjacent surfaces.

 The floor or build-in unit must be rated to support the weight of the appliance

 To ensure that it is stable, level the appliance with its four feet.

 The appliance is intended for fixed installation only; any other approaches must

be agreed with and approved by the manufacturer.

 Remove the protective film from its body panels before operating the

dishwasher.

INSTRUCTION MANUAL FOR DISHWASHERS

Page 5 of 14

UK

Mod.

V~

Hz

kW

A

S/N

H2O

kPa

°C

3.3 Electrical connection

 The power supply must be fitted with a omnipolar circuit breaker (master power

switch) to break all contacts including neutral, with a contact gap of at least 3

mm and thermal cutout or fuses, which must be set or rated to the power

indicated on the machine's nameplate.

 The master power switch must be fitted to the power line in the vicinity of the

installation and may be connected to only one machine at a time.

 The mains voltage and frequency must match the nameplate ratings.

 The installation must include a grounding system conforming with established

electrical safety legislation, to protect the operator and the appliance itself

 This appliance conforms to EN/IEC 61000-3-11 certification if the system impedance Zsys is less

than or equal to Zmax in the point of interface between the user’s supply system and the public

system. The installer or appliance user is responsible for checking that the appliance is connected

exclusively to a supply with system impedance Zsys less than or equal to Zmax

Zmax

Utensil washers

0.21 Ω

Hood

0.24 Ω

Undercounter

0.41 Ω

 The power cable, which must be exclusively type H07RN-F with current capacity at 60°C on the

cable:

 Three-phase machine

o -5x2.5 mm^2 up to 20 A

o -5x4 mm^2 up to 30 A

o -5x6 mm^2 up to 38 A

o -5x10 mm^2 up to 54 A

 Single-phase machines

o -3x1.5 mm^2 up to 16 A

o -3x2.5 mm^2 up to 25 A

 Must not be stretched or crushed during normal operation or routine maintenance.

 The appliance must also be connected to an equipotential system, connected by a screw marked

by the symbol 5021 - IEC 60417.

 The equipotential cable must have a cross section of 10 mm².

 Respect the polarities indicated in the wiring diagram.

 For further information, refer to the wiring diagram.

Do not use multi-sockets, adapters, cables of an inadequate cross section or type or

with extensions not conforming to established electrical installation regulations.

INSTRUCTION MANUAL FOR DISHWASHERS

Page 6 of 14

UK

3.4 Water circuit hookup

The appliance must be connected to its water supply with a flexible hose. A

shut off valve (cock) must be installed between the water supply line and

the appliance's solenoid valve. The cock must be close to the appliance.

 The water supply, temperature and pressure must be compatible with the ratings shown on the

technical data plate on the machine.

 Make sure that the water supply flow rate is no less than 20 l/min

 If the water hardness is greater than 14 °f (8 °dH), we recommend using an internal water softener.

If the water hardness is greater than 35 °f (19.5 °dH), install an external water softener upline of

the solenoid valve

 For machines without water softener: if the water hardness is greater than 14 °f (8 °dH), install an

external water softener upline of the solenoid valve.

 If the water has a very high residual concentration of high conductivity minerals, we recommend

installing a demineralisation system.

 Machines intended for use with desalinated water or in any case with high sodium chloride

concentration must be ordered specifically, as they require specific construction materials

 Do not supply fully demineralised water to machines with a heat recovery unit with batteries with

copper pipes. In this case, request the version with batteries with stainless steel pipes.

Free drain

3.5 Connection to the drain line

 The drain line must consist of a free drain sump with siphon suited to

the flow capacity of the drain hose supplied with the appliance. The

hose must be able to reach the sump without stretching, restriction,

folding, crushing, pressing or forcing in any way.

 The tub drains under gravity, so the drain sump must be lower than the

machine's base.

Max.

1 m

With pump (available on request)

 if the drain is not lower than the base of the appliance, you can use the

version with drain pump (available on request).

 In this case, the drain connection may be no higher than 1 m.

 Always check that the drain works properly and is not blocked.

 Any other solution must be approved by the manufacturer in advance.

3.6 Rinse aid and detergent

 The rinse aid and detergent are dispensed by the machine's integral dispenser (depending on

model).

 The dose is set by the installer in relation to the hardness of the water, and he also calibrates the

dispensers themselves.

 Before calibrating them, fill the dispenser supply tubes with their respective product.

 The units are calibrated with the adjuster screws, or directly with the control panel (as applicable).

 The level of fluid in the container must be sufficient for priming; do not allow it to drain completely

or top it up with corrosive or impure product.

NEVER use CHLORINE or HYPOCHLORITE based detergents.

We recommend installing an automatic detergent dispenser.

INSTRUCTION MANUAL FOR DISHWASHERS

Page 7 of 14

UK

Chap 4 USING THE MACHINE

4.1 Key and symbols

Referring to Fig.1:

1

ON/OFF BUTTON

5

WASHING LED

2

STATUS SELECTION BUTTON

6

RINSE LED

3

PROGRAMME SELECTION BUTTON

7

INFORMATION DISPLAY

4

START BUTTON

8

REGENERATION LED

The arrangement of buttons and leds may vary according to the machine type

4.2

Switching the dishwasher on

 Turn on the main power switch and open the external water tap.

 The two lines on the DISPLAY (7) show that the mains power is on.

 Check the presence of the overflow.

 Press ON/OFF (1).

 The water filling and heating stage starts automatically; LEDs (5) and (6) flash alternately and the

boiler temperature is shown on the DISPLAY (7).

 When the LEDs (5) and (6) stop flashing and stay steadily illuminated, this indicates that the

optimum conditions to start washing have been reached.

4.3

Filling the rack

Referring to Fig.3,

to ensure the correct operation of the dishwasher follow the rules described below:

 Use a suitable rack, fill without overloading and without overlapping the dishes.

 Always wipe the dishes before placing in the dishwasher; do not put dishes with dry or solid

residues in the washer.

 Place the empty dishes in the rack facing downwards.

 Place plates and the like in the sloping rack, with the inner surface facing upwards.

 Place the cutlery in the cutlery basket, handle end down.

 Do not place silver and stainless steel cutlery in the same cutlery basket as this will turn the silver

brown and may corrode the steel.

 Wash the dishes immediately after use, in order to prevent any residue from hardening and sticking

on them.

 Use only solid, dishwasher-proof dishes.

4.4

Cycle selection and start-up

4.4.1 Under-counter dishwashers

 Select the appropriate washing cycle for the dishes using the buttons STATUS SELECTION (2)

and PROGRAMME SELECTION (3); these buttons are used in combination to select the desired

cycle, as shown in Fig.2.

 To start the programme, press the START button (4). The WASHING LED (5) will start flashing and

the DISPLAY will show the washing temperature. Subsequently the RINSE LED (6) will start

flashing and the DISPLAY will show the rinse temperature.

(Fig.1 ).

 At the end of the cycle, the WASHING (5) and RINSE (6) LEDs will flash simultaneously for a few

seconds.

 For rapid drying, remove the rack from the machine as soon as the cycle finishes.

 To stop a wash cycle early, press down and hold the START (4) button for a few seconds.

INSTRUCTION MANUAL FOR DISHWASHERS

Page 8 of 14

UK

4.4.2 Hood dishwashers

 Select the appropriate washing cycle for the dishes using the buttons STATUS SELECTION (2)

and PROGRAMME SELECTION (3); these buttons are used in combination to select the desired

cycle, as shown in Fig.2.

 Press the START button (4) to activate the automatic start. The WASHING LED (5) will start

flashing and the DISPLAY will show the washing temperature. Subsequently the RINSE LED (6)

will start flashing and the DISPLAY will show the rinse temperature.

(Fig.1 ).

 At the end of the cycle, the WASHING (5) and RINSE (6) LEDs will flash simultaneously for a few

seconds.

 Subsequent cycles will start automatically on closing the hood.

 For rapid drying, remove the rack from the machine as soon as the cycle finishes.

 To stop a wash cycle early, press START (4).

4.5 Programmes

Glasswashers

Dishwashers

Short wash

Long wash

Medium wash

Drain cycle.

Long wash

Resin regeneration

Glass wash

Drain cycle.

Resin regeneration

4.6 Removing the integral filter

 Move the washing and rinsing arms at right angles to the edge of the door (Fig.4).

 Lift each semi-filter by the relative handle.

4.7 Emptying the dishwasher

4.7.1 Appliances with no drain pump

 Switch the dishwasher off.

 If present, remove the integral filter (Fig.4 A).

 Pull up and remove the overflow pipe (Fig. 5 B).

 Wait for the tub to empty completely.

 If necessary, extract the tub filter and clean (Fig. 5 C).

4.7.2 Appliances with drain cycle (*optional)

 Turn off the machine by pressing the ON/OFF button (1).

 If present, remove the integral filter (Fig.4 A).

 Withdraw the overflow, if present, by pulling it upwards (Fig.5 B); the overflow is not present on

partial drain versions.

 Close the door.

 Select the drain cycle by pressing STATUS SELECTION (2).

 Press the START button (4) for 2 seconds to activate the drain cycle.

 The drain cycle is indicated on the DISPLAY (7) by the letters dr.

 The machine runs a drain cycle and then switches off.

 If necessary, extract the tub filter and clean (Fig. 5 C).

INSTRUCTION MANUAL FOR DISHWASHERS

Page 9 of 14

UK

4.8

Resin regeneration (*optional)

In machines with internal water softener, a regeneration cycle should be run periodically to ensure the

correct operation of the softener. The number of cycles between one resin regeneration and the next

depends on the hardness of the local water, and should be set in accordance with the following table.

dH

°F

No.

Cycles

dH

°F

No.

Cycles

6

10

160

13

23

90

7

12

150

14

25

80

8

14

140

15

27

70

9

16

130

16

29

60

10

18

120

17

30

50

11

20

110

18

32

40

12

21

100

19

34

30

Proceed as follows (Fig. 6):

 Switch the dishwasher off

 Empty and clean it.

 Remove the integral filter and open the salt container in the tub.

 Pour in 250-300g of regeneration salt (1 or 2mm grain size kitchen salt with no additives).

 Close the container firmly.

 Make sure the overflow has been removed.

 Select the regeneration cycle by pressing STATUS SELECTION (2).

 To start the cycle, with the machine off, press the START button (4) for a few seconds.

 The start of the cycle will be signalled by illumination of the REGENERATION LED (8).

 The regeneration cycle lasts around 20 minutes.

 The dishwasher will switch off when the cycle has completed.

N.B. Do not switch the machine off during the regeneration cycle

4.9 List of viewable messages

Door open

Drain cycle.

4.10 End of shift

 At the end of the day always drain the machine as described in the section Machine draining.

 Disconnect the power supply by means of the main switch and close the external water cock.

 Perform routine maintenance and clean the machine as described in the section Maintenance.

 If possible, leave the door ajar to prevent bad odours building up inside the machine.

INSTRUCTION MANUAL FOR DISHWASHERS

Page 10 of 14

UK

Chap 5 MAINTENANCE

5.1 General rules

Before doing any maintenance, completely drain out all water, shut off the power

supply and close the water supply cock.

Do not use water under pressure - it can damage the electrical equipment.

Only wash the body panelling when it is cold, using only product specifically designed for steel.

If there is a risk of ice forming, drain the water from the boiler and wash pump.

5.2 Cleaning

To keep the machine in good working order, it must be maintained regularly as explained below. We

recommend periodically running a sanitising treatment with suitable non-corrosive commercial

products.

5.3 Cleaning the filter unit

Run this procedure at the end of the day or when you see the filters are dirty:

1. Remove and clean the baskets.

2. Empty out the tub as explained in “Machine draining”.

3. Remove and carefully clean all the filters.

4. Do not use abrasive products to clean the tub.

5. Restore all removed parts when finished.

5.4 Cleaning the arms

The wash and rinse arms are easily removed in order to clean their nozzles and prevent

blockage/encrustations.

Proceed as follows:

 Remove the spray arms by unscrewing the retaining nuts or by unclipping the quick-fit attachments

on machines so equipped.

 Wash all parts under a jet of running water and clean the nozzles thoroughly, using a toothpick or

pointed tool if necessary.

 Clean the arm rotation pins inside the machine and the wash and rinse water drainage area.

 Restore the arms and check that they rotate freely.

INSTRUCTION MANUAL FOR DISHWASHERS

Page 11 of 14

UK

Chap 6 SELF DIAGNOSTICS

The machine is equipped with a self-diagnosis system that registers and warns of a number of

malfunctions.

Fault

Description and possible remedies

No rinsing. The rinsing cycle was not completed correctly. Make sure that the rinsing

nozzles are clean.

No drainage. The water was not drained or drained incorrectly. Check that the drain

pipe is not bent or crushed and that the siphon and filters are not blocked. In machines

fitted with an overflow pipe, remove this before starting the drainage cycle.

Rinsing temperature reset fault. The boiler temperature did not reset in the set time

during the washing cycle. Switch the machine off and then on and run a new cycle.

SAFE

Water filling in tank fault. Make sure the pipes are connected correctly, and that the

water tap is open. Where foreseen, check the presence of the overflow. Switch the

dishwasher off and then on and fill again.

Tank thermometer fault. (Probe open) The machine does not read the tank

temperature value. Switch the dishwasher off and then on.

Tank thermometer fault. (Probe short circuited) The machine does not read the

tank temperature value. Switch the dishwasher off and then on.

Boiler thermometer fault. (Probe open) The machine does not read the boiler

temperature value. Switch the dishwasher off and then on.

Boiler thermometer fault. (Probe short circuited) The machine does not read the

boiler temperature value. Switch the dishwasher off and then on.

Boiler loading time out: boiler not filled. Impossible to carry out rinse cycle. Check

that the water tap is open. Switch the dishwasher off and then on and run a new

cycle.

Insufficient rinse: the right amount of rinsing did not take place; make sure the rinse

nozzles are clean. The error does not stop machine operation.

Tank temperature reset fault: The tank temperature did not reset in the set time

during the washing cycle. Switch the machine off and then on and run a new cycle.

SAFE

Electro-mechanical safety device: the boiler or tub safety thermostats have cut in,

or the tub safety pressure switch has been triggered.

SAFE

Level safety switch: Incorrect water level in the tank.

WARNING! Switching the dishwasher off and then on again "resets" the signals, if after

carrying out the instructions given the problem persists, contact an Authorised Service Centre.

INSTRUCTION MANUAL FOR DISHWASHERS

Page 12 of 14

UK

Chap 7 SETTINGS

The following settings should only be configured by a qualified technician.

The parameters listed below can be set during installation or afterwards, accessing the settings menu

as follows:

 With the machine on and the door open.

 Hold pressed START (4) for 5 seconds; the boiler temperature will appear on the DISPLAY (7).

 It will then be possible to change the value indicated by repeatedly pressing START (4).

 Once you have selected the desired value, hold pressed START (4) to confirm and move to the

next parameter.

 The parameters will be displayed in the order indicated in the table below.

Tank

Temperature

Tub temperature setting.

The change will only be applied to the programme at the moment

selected.

Boiler

Temperature

Boiler temperature setting.

The change will only be applied to the programme at the moment

selected.

Dosage

Detergent

Detergent dosing time.

Dosage

Rinse Aid

Rinse aid dosing time.

The list of parameters may vary according to the type of machine.

Chap 8 SCRAPPING

Our machines do not contain materials requiring special handling.

(Applicable in the EU and countries with sorted waste disposal)

The mark applied to the product or its documentation indicates that it must not be

scrapped with domestic

waste when it reaches the

end of its service life. To

prevent damage to the

environment or health risks

due to improper scrapping, keep this

product separate from other waste and

recycle it so as to promote sustainable

use of materials.

Corporate users are requested to contact

their supplier and check the terms and

conditions of the purchase contract.

The product may not be scrapped together

with other commercial waste.

Symbols

Object

Material

%

Recyclable

directly

Sheet

Steel

80

Cardboard packaging

PAP

Wooden pallet

ISPM15

Plastic parts

PP, PP+FV

Compounds

W

E

Motors

Assemblies

20

Electric parts

Electronic parts

Rubber parts

EPDM

INSTRUCTION MANUAL FOR DISHWASHERS

Page 13 of 14

UK

Chap 9 ENVIRONMENT

RESPECT FOR THE ENVIRONMENT

Proper use of the dishwasher can improve its environmental footprint, if the following simple rules are

observed:

Only wash full baskets.

Switch the dishwasher off when not using it.

Keep the machine closed when it is in standby.

Use wash programmes suited to the amount of soiling.

Supply the machine with hot water, if gas heated.

Make sure the drains flow into a suitable sewer.

Do not exceed the recommended dose of detergent.

The manufacturer reserves the right to modify the electrical, technical and aesthetic features of this

appliance and replace any of its parts without notice, as he deems necessary to offer a reliable

product with a long service life and advanced technology.

BEDIENUNGSANLEITUNG FÜR GESCHIRRSPÜLMASCHINE

Seite 1 von 14

DE

ÜBERSETZUNG DER ORIGINAL-BEDIENUNGSANLEITUNG

INHALT

KAP 1 RISIKEN UND WICHTIGE WARNHINWEISE ............................................................. 2

1.1 NORMALE BETRIEBSBEDINGUNGEN .................................................................................... 3

KAP 2 EINLEITUNG ............................................................................................................... 4

KAP 3 INSTALLATION .......................................................................................................... 4

3.1 AUSPACKEN ...................................................................................................................... 4

3.2 AUFSTELLUNG ................................................................................................................... 4

3.3 ELEKTRISCHER ANSCHLUSS ............................................................................................... 5

3.4 WASSERANSCHLUSS ......................................................................................................... 6

3.5 ABFLUSSANSCHLUSS ......................................................................................................... 6

3.6 KLARSPÜLMITTEL UND REINIGER ................................................................................. 6

KAP 4 BENUTZUNG DER SPÜLMASCHINE ........................................................................ 7

4.1 LEGENDE UND ZEICHENERKLÄRUNG ................................................................................... 7

4.2 EINSCHALTEN ................................................................................................................... 7

4.3 DEN GESCHIRRKORB BELADEN .......................................................................................... 7

4.4 PROGRAMMAUSWAHL UND –START ..................................................................................... 7

4.4.1 Einbauspülmaschinen ........................................................................................ 7

4.4.2 Durchschubspülmaschinen ................................................................................ 8

4.5 PROGRAMME .................................................................................................................... 8

4.6 ENTNEHMEN DES BODENSIEB ............................................................................................ 8

4.7 ENTLEEREN DER SPÜLMASCHINE ....................................................................................... 8

4.7.1 Geräte ohne Ablaufpumpe ................................................................................. 8

4.7.2 Geräte mit Ablaufpumpe (* optional) .................................................................. 8

4.8 REGENERIERUNG DER AUSTAUSCHHARZE (* OPTIONAL) ...................................................... 9

4.9 ÜBERSICHT DER MÖGLICHEN ANZEIGEN .............................................................................. 9

4.10 BETRIEBSENDE ................................................................................................................. 9

KAP 5 WARTUNG ................................................................................................................ 10

5.1 ALLGEMEINE REGELN ...................................................................................................... 10

5.2 REINIGUNG ..................................................................................................................... 10

5.3 REINIGUNG DER FILTERGRUPPE ....................................................................................... 10

5.4 REINIGUNG DER SPÜLARME ............................................................................................. 10

KAP 6 SELBSTDIAGNOSE ................................................................................................. 11

KAP 7 EINSTELLUNGEN UND ANPASSUNGEN ............................................................... 12

KAP 8 ENTSORGUNG ......................................................................................................... 12

KAP 9 UMWELT ................................................................................................................... 13

Der Hersteller behält sich entsprechend der Gesetze die Eigentumsrechte am vorliegenden Dokument vor. Ohne vorherige schriftliche

Genehmigung sind die Vervielfältigung und Weitergabe dieses Dokuments verboten.

Der Hersteller behält sich dass Recht vor ohne Vorankündigung durch Verbesserungen, die von ihm für notwendig befunden wurden,

die vorliegende Anleitung zu ändern.

442470 MD REV02 26-10-2020 U DE

BEDIENUNGSANLEITUNG FÜR GESCHIRRSPÜLMASCHINE

Seite 2 von 14

DE

Lesen Sie die Betriebsanleitung vor der Inbetriebnahme des Geräts

aufmerksam durch. Sie enthält wichtige Hinweise und

Sicherheitsanweisungen für Installation, Gebrauch und Wartung. Die

Nichtbeachtung der Angaben der beigefügten Unterlagen kann die Sicherheit

des Geräts beeinträchtigen und zum sofortigen Verfall der Garantie führen.

Kap 1 RISIKEN UND WICHTIGE WARNHINWEISE

 Dieses Gerät ist nur für den Gebrauch vorgesehen, für den es ausdrücklich

entwickelt wurde. Jede andere Verwendung gilt als unsachgemäß und

demzufolge gefährlich.

 Das Installations-Fachpersonal ist angehalten, den Benutzer auf

angemessene Weise über die Bedienung des Geräts und eventuell zu

beachtende Sicherheitsmaßnahmen, auch mit praktischen Vorführungen, zu

unterrichten.

 Alle Arbeiten an der Maschine, auch bei Störung bzw. Ausfall, müssen vom

Hersteller oder einem autorisierten Kundendienstzentrum bzw. von

Fachpersonal vorgenommen werden. Dabei dürfen ausschließlich

Originalersatzteile verwendet werden.

 Vor Wartungsarbeiten, Reparaturen und Reinigung die Maschine stets vom

Stromnetz und vom Wasseranschluss trennen.

 Die Maschine darf NICHT von ungeschultem Personal benutzt werden.

 Dieses Gerät darf nur dann von Kindern ab 8 Jahren und Personen mit

eingeschränkten körperlichen, sensorischen oder geistigen Fähigkeiten oder

von Personen mit mangelnder Erfahrung bzw. mangelnden Kenntnissen

verwendet werden, wenn sie beaufsichtigt werden oder in die sichere

Bedienung des Geräts eingewiesen wurden.

 Kinder nicht mit dem Gerät spielen lassen.

 Die Reinigung und Pflege durch den Benutzer darf nicht von Kindern

ausgeführt werden, es sei denn, sie werden beaufsichtigt.

 Bei Nichtbenutzung darf die Maschine NICHT unter Spannung bleiben.

 Falls an der Maschine kein Stecker und keine andere Vorkehrung vorhanden

ist, um sie vollständig vom Stromnetz zu trennen und alle Kontakte zu

unterbrechen, müssen die erforderlichen Trennvorrichtungen

vorschriftsmäßig im Versorgungsnetz installiert werden.

 Ein beschädigtes Netzkabel durch den Hersteller bzw. seinen Kundendienst

oder auf jeden Fall durch eine Fachkraft mit ähnlicher Qualifikation ersetzten

lassen, um jedes Risiko auszuschließen.

 Das Symbol 5021 nach IEC-Norm 60417 an der Schraube am Gerät

kennzeichnet den Schutzpotenzialausgleich.

 Solange der Spülzyklus läuft, die Gerätetür KEINESFALLS – auch nicht kurz

– öffnen.

 Die Maschine KEINESFALLS ohne die vom Hersteller vorgesehenen

Schutzvorrichtungen benutzen.

BEDIENUNGSANLEITUNG FÜR GESCHIRRSPÜLMASCHINE

Seite 3 von 14

DE

 In der Maschine NIEMALS Gegenstände spülen, die nicht

spülmaschinenfest sind, aufgrund ihrer Form oder Abmessungen nicht in der

Spülmaschine gereinigt werden dürfen oder nicht in einwandfreiem Zustand

sind.

 Das Gerät oder Geräteteile NIEMALS als Leiter oder Halt für Personen,

Sachen oder Tiere verwenden.

 Die geöffnete Klappe eines Frontlader-Geschirrspülers NIEMALS überlasten.

Die Klappe ist so ausgelegt, dass sie nur den mit Geschirr beladenen Korb

aushält.

 NIEMALS die nackten Hände in die Spüllaugen tauchen.

 Die Maschine nach der Installation NIEMALS kippen.

 Im Fall einer Störung oder einer Leckage sofort die Stromzufuhr unterbrechen

und den Wasserzulaufhahn schließen.

 Die Spülmaschine nicht in der Nähe von Wärmequellen über 50 °C aufstellen.

 Die Spülmaschine NIEMALS der Witterung aussetzen (Regen, Sonne, usw.).

 Die Spülmaschine darf ohne geeignete Schutzabdeckungen nicht in

Außenbereichen installiert werden.

 Nie ein Spülprogramm ohne den Überlauf starten (sofern vorgesehen).

 Nie magnetische Gegenstände in Maschinennähe bringen.

 Die Oberseite der Maschine nicht als Ablage benutzen.

 Der Installateur muss die vorschriftsmäßige Erdung überprüfen.

 Nach erfolgter Prüfung muss der Installateur eine schriftliche Erklärung

ausstellen und bestätigen, dass die Installation und die Abnahmeprüfung

ordnungsgemäß und fachgerecht nach den gesetzlichen Bestimmungen

ausgeführt wurden.

 Die Position einzelner Geräteteile NICHT verändern und keine Eingriffe

daran vornehmen, da hierdurch die Sicherheit des Gerätes beeinträchtigt

werden könnte.

 Schalldruckpegel gemäß EN ISO 4871

o LpA Max = 55 db Kpa=2,5 db für Einbaumaschinen

o LpA Max = 65 db Kpa=2,5 db für Durchschubspülmaschinen

o LpA Max = 76 db Kpa=1,5 db für Gerätespülmaschinen

 Max. Temperatur des Leitungswassers: 50 °C

 Max. Druck des Leitungswassers: 4 bar (400 kPa)

 Gerät für den dauerhaften Anschluss an das Wasserversorgungsnetz

 Das Gerät darf nicht mit Hochdruck- oder Dampfreinigern gereinigt werden.

 Max. Höhe des Ablaufs

o Bodenhöhe bei Ausführungen mit Überlauf

o Max. Höhe 1 m bei Ausführungen mit Laugenpumpe

1.1 Normale Betriebsbedingungen

Umgebungstemperatur : 40°Cmax /4°Cmin ( Mittelwert 30°C)

Höhe : bis 2000 Meter

Relative Feuchte : Max 30% bei 40°C / max 90% bei 20°C

BEDIENUNGSANLEITUNG FÜR GESCHIRRSPÜLMASCHINE

Seite 4 von 14

DE

Kap 2 EINLEITUNG

Hinweise:

Die gesamte Dokumentation sorgfältig in der Nähe des Geräts aufbewahren. Sie muss den

Technikern und Bedienern ausgehändigt und an einem sicheren Ort sorgfältig aufbewahrt

werden; bei Bedarf Kopien anfertigen, die ein häufiges Nachschlagen erlauben

Der Bediener ist verpflichtet, die vorliegende Bedienungsanleitung vor jeglicher Arbeit

an der Maschine zu lesen, zu verstehen und zu lernen.

Das Gerät ist für das gewerbliche Geschirrspülen in Gemeinschaftsküchen vorgesehen, d. h.

die Installation, der Betrieb und die Wartung erfolgen durch ausgebildetes Fachpersonal, das

sich an die Herstelleranweisungen halten muss.

Garantie:

Der Hersteller übernimmt keinerlei Haftung für Sach- oder Personenschäden, die aus der

Nichtbeachtung der gegebenen Anweisungen oder einem unsachgemäßen Einsatz der

Maschine entstehen

Die Nichtbeachtung der in der vorliegenden Anleitung enthaltenen Anweisungen kann die

Sicherheit des Geräts beeinträchtigen und führt zum sofortigen Verfall der Garantie

Die Ausführung von Installations- und Reparaturarbeiten durch nicht autorisiertes Personal und

die Verwendung von Nichtoriginal-Ersatzteilen führen zum sofortigen Verfall der Garantie.

Lagerung :

Transport und Lagerung : von -10°C bis 55°C mit Höchstwerten bis 70°C (max. 24 h)

Kap 3 INSTALLATION

Eine richtige Installation ist grundlegende Voraussetzung für ein gutes Funktionieren der Maschine.

Einige notwendige Angaben für die Maschineninstallation befinden sich auf dem Typenschild auf der

rechten Maschinenseite, eine Kopie ist auf dem Deckblatt dieser Bedienungsanleitung wiedergegeben.

Die Installation darf ausschließlich von qualifiziertem und autorisiertem Fachpersonal

vorgenommen werden.

3.1 Auspacken

Die Verpackung auf Schäden überprüfen. Eventuell bemerkte Schäden auf dem Lieferschein

vermerken. Nach der Entfernung der Verpackung sicherstellen, dass das Gerät sich in einwandfreiem

Zustand befindet. Wenn die Maschine beschädigt ist, sofort den Vertragshändler per Fax oder

Einschreiben mit Rückantwort und das Transportunternehmen davon unterrichten. Wenn die Schäden

die Maschinensicherheit beeinträchtigen, die Maschine bis zum Eingriff eines Fachtechnikers nicht

installieren und/oder benutzen.

Die Verpackungsteile (Plastikbeutel, Styropor, Nägel usw. ...) von Kindern und

Haustieren fernhalten. Die Verpackungsteile können eine Gefahrenquelle darstellen.

3.2 Aufstellung

 Prüfen, dass sich im Installationsbereich keine Gegenstände oder Materialien

befinden, die vom Wasserdampf, der während des Betriebs aus der Maschine

austreten kann, beschädigt werden können, bzw. dass diese ausreichend

geschützt sind.

 Vor der Installation des Geschirrspülers die elektrischen Anlage sowie die

Wasserzulauf- und Wasserablaufanschlüsse vorbereiten.

 Bei Einbau von Maschinen mit Seitenwänden ohne Wärmedämmung

mindestens 10 mm Abstand zwischen den Gerätewänden und den

angrenzenden Oberflächen belassen.

 Der Fußboden oder die Einbauöffnung müssen für das Gesamtgewicht des

Geschirrspülers ausgelegt sein

 Um die Stabilität sicherzustellen, die Maschine installieren und mit den vier

La page charge ...

Elettrobar 570180 Manuel utilisateur

Ce manuel convient également à

Elettrobar 570180 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents