Blackstone 1948 Pro Series Prep/Serve and Store Cart Le manuel du propriétaire

Taper
Le manuel du propriétaire
ENGLISH
ENGLISH
North Atlantic Imports LLC | 1073 West 1700 North Logan, UT 84321 USA | Blackstoneproducts.com
OWNER’S MANUAL
SERVE & STORE
PREP CART
Model 1948 v12
ENGLISHENGLISH
Owner’s Manual |
blackstoneproducts.com/support
ENGLISH
TABLE OF CONTENTS
It is the consumer’s responsibility to see that the unit is properly assem-
bled, installed, and maintained. Failure to follow the instructions in this
manual could result in bodily injury and/or property damage.
!DANGER
Indicates an imminently
hazardous situation which,
if not avoided, may result in
death or serious injury.
!WARNING
Indicates the possibility of
serious bodily injury if the
instructions are not followed.
!CAUTION
Indicates a potentially
hazardous situation which,
if not avoided, may result in
minor or moderate injury.
SAFETY ALERT KEY
Read and follow all the notices
throughout the manual.
ENGLISH
NORTH ATLANTIC IMPORTS LLC
YEAR WARRANTY
North Atlantic Imports LLC
warrants to the owner that the
product covered by this agreement
is free from defects in material and
workmanship under normal use and
service for which it was intended
if, but only if, it has been operated
in accordance with North Atlantic
Imports LLC instructions exclu-
sively for domestic use, and not for
private or public club, institutional
or commercial purposes.
North Atlantic Imports LLC’s obliga-
tion under this warranty is limited
to replacing or repairing, free of
charge, any part or parts that may
prove, to the satisfaction of North
Atlantic Imports LLC, to be defective
under normal home use and service
within the following stated periods
of time from the date of purchase;
for one year from purchase, all parts,
nish, and workmanship. Should
any failure to conform to this
warranty become apparent during
applicable warranty periods stated
above, the original purchaser must
notify North Atlantic Imports LLC
of breach of warranty within the
applicable warranty period.
North Atlantic Imports LLC shall
upon notice and compliance by
the original purchaser with such
instructions, correct such noncon-
formity by repair or replacement of
the defective part or parts.
Correction in the manner provided
above shall constitute a fulllment
of all obligations of North Atlantic
Imports LLC with respect to the
quality of the product.
North Atlantic Imports LLC does
not warrant this equipment to
meet the requirement of any safety
code of any state, municipality or
other jurisdiction, and the orig-
inal purchaser assumes all risk
and liability whatsoever resulting
from the use thereof, whether
used in accordance with North
Atlantic Imports LLC instructions
or otherwise.
This warranty does not cover and is
intended to exclude any liability on
the part of North Atlantic its agents,
servants or employees whether
under this warranty or implied
by law for any indirect or conse-
quential damages for breach on
any warranty. The purchaser must
establish all applicable warranty
periods pursuant to this warranty
by verifying the original purchase
date by producing the dated sales
receipt. This warranty shall not
apply to this product or any other
part thereof which has been subject
to accident, negligence, alteration,
abuse, or misuse or which has been
repaired or altered without North
Atlantic written consent, outside of
North Atlantic Imports LLC factory.
The full manufacturer warranty
is not valid for griddles purchased
from unlicensed, third-party
resellers, purchased at a discount
due to missing or damaged parts, or
purchased as a oor model; at the
discretion of North Atlantic Imports.
North Atlantic Imports LLC makes
no warranty whatsoever in respect
to accessories or parts not supplied
with it. This warranty shall apply
only within the boundaries of
the United States of America.
This warranty gives the original
purchaser specic rights, and the
original purchaser may also have
other rights, which vary from
state to state.
North Atlantic Imports, the manufacturer, will warranty for one year from
purchase all parts, workmanship, and nishes. It will be the manufacturer’s
option as to whether to repair or replace any of the above items. All warran-
ties are limited to the original purchaser only. This warranty does not cover
any liability on the part of North Atlantic Imports, its agents or employees,
for any indirect or consequential damages for breach of warranty. The
purchaser must follow the manufacturer’s usage instructions.
Under no circumstances is the manufacturer responsible for damages from
the failure to operate the cooking station properly. It is the responsibility
of the purchaser to establish the warranty period by verifying the original
purchase date with original sales receipt.
For more detailed explanation of the warranty, read below:
Warranty
CONTENTS
01. WARRANTY .................................................01
02. ASSEMBLY GUIDE ...........................................02
ii
Model 1948
ENGLISHENGLISH
| Owner’s Manual
blackstoneproducts.com/support
ENGLISH
TABLE OF CONTENTS
It is the consumer’s responsibility to see that the unit is properly assem-
bled, installed, and maintained. Failure to follow the instructions in this
manual could result in bodily injury and/or property damage.
!DANGER
Indicates an imminently
hazardous situation which,
if not avoided, may result in
death or serious injury.
!WARNING
Indicates the possibility of
serious bodily injury if the
instructions are not followed.
!CAUTION
Indicates a potentially
hazardous situation which,
if not avoided, may result in
minor or moderate injury.
SAFETY ALERT KEY
Read and follow all the notices
throughout the manual.
ENGLISH
NORTH ATLANTIC IMPORTS LLC
YEAR WARRANTY
North Atlantic Imports LLC
warrants to the owner that the
product covered by this agreement
is free from defects in material and
workmanship under normal use and
service for which it was intended
if, but only if, it has been operated
in accordance with North Atlantic
Imports LLC instructions exclu-
sively for domestic use, and not for
private or public club, institutional
or commercial purposes.
North Atlantic Imports LLC’s obliga-
tion under this warranty is limited
to replacing or repairing, free of
charge, any part or parts that may
prove, to the satisfaction of North
Atlantic Imports LLC, to be defective
under normal home use and service
within the following stated periods
of time from the date of purchase;
for one year from purchase, all parts,
nish, and workmanship. Should
any failure to conform to this
warranty become apparent during
applicable warranty periods stated
above, the original purchaser must
notify North Atlantic Imports LLC
of breach of warranty within the
applicable warranty period.
North Atlantic Imports LLC shall
upon notice and compliance by
the original purchaser with such
instructions, correct such noncon-
formity by repair or replacement of
the defective part or parts.
Correction in the manner provided
above shall constitute a fulllment
of all obligations of North Atlantic
Imports LLC with respect to the
quality of the product.
North Atlantic Imports LLC does
not warrant this equipment to
meet the requirement of any safety
code of any state, municipality or
other jurisdiction, and the orig-
inal purchaser assumes all risk
and liability whatsoever resulting
from the use thereof, whether
used in accordance with North
Atlantic Imports LLC instructions
or otherwise.
This warranty does not cover and is
intended to exclude any liability on
the part of North Atlantic its agents,
servants or employees whether
under this warranty or implied
by law for any indirect or conse-
quential damages for breach on
any warranty. The purchaser must
establish all applicable warranty
periods pursuant to this warranty
by verifying the original purchase
date by producing the dated sales
receipt. This warranty shall not
apply to this product or any other
part thereof which has been subject
to accident, negligence, alteration,
abuse, or misuse or which has been
repaired or altered without North
Atlantic written consent, outside of
North Atlantic Imports LLC factory.
The full manufacturer warranty
is not valid for griddles purchased
from unlicensed, third-party
resellers, purchased at a discount
due to missing or damaged parts, or
purchased as a oor model; at the
discretion of North Atlantic Imports.
North Atlantic Imports LLC makes
no warranty whatsoever in respect
to accessories or parts not supplied
with it. This warranty shall apply
only within the boundaries of
the United States of America.
This warranty gives the original
purchaser specic rights, and the
original purchaser may also have
other rights, which vary from
state to state.
North Atlantic Imports, the manufacturer, will warranty for one year from
purchase all parts, workmanship, and nishes. It will be the manufacturer’s
option as to whether to repair or replace any of the above items. All warran-
ties are limited to the original purchaser only. This warranty does not cover
any liability on the part of North Atlantic Imports, its agents or employees,
for any indirect or consequential damages for breach of warranty. The
purchaser must follow the manufacturer’s usage instructions.
Under no circumstances is the manufacturer responsible for damages from
the failure to operate the cooking station properly. It is the responsibility
of the purchaser to establish the warranty period by verifying the original
purchase date with original sales receipt.
For more detailed explanation of the warranty, read below:
Warranty
01
Model 1948
ENGLISHENGLISH
Owner’s Manual |
blackstoneproducts.com/support
ENGLISH
ASSEMBLY GUIDE
ILLUSTRATED PARTS LIST
  BOX 1 Top drawer
panel (1 piece)
2 Le leg
assembly (1 piece)
3 Right leg
assembly (1 piece)   BOX
Inside № 1 Box
4 Le rear
panel (1 piece)
  BOX 5 Bottom
panel (1 piece)
6 Table top
(1 piece)
7 Lid handle
(1 piece)
8 Right rear
panel (1 piece)
9 Cart door
(1 piece)
10 Garbage bag
holder (1 piece)
11 Center
drawer panel
(1 piece)
  BOX
Inside № 2 Box
12 Right side
shelf (1 piece)
13 Le side
shelf (1 piece)   BOX
Inside № 7 Box
  BOX 14 Bottom
drawer (1 piece)
15 Paper towel
holder (1 piece)
16 Paper towel
holder bracket
(1 piece)
17 Caster
wheels (2 pieces)
18 Fixed
wheels (2 pieces)
19 Small
drawers (2 pieces)
20 Seasoning
boxes (4 pieces)
21 Seasoning
box lids (4 pieces)
22 Faucet hose
(1 piece)
23 Bottom
drawer plug
(1 piece)
24 Inner gasket
(1 piece)
25 Outer
gasket (1 piece)
26 Filter cover
(1 piece)
27 Filter
(1 piece)
28 Inner water
output (1 piece)
29 Outer water
output (1 piece)
02
Model 1948Assembly Guide
ENGLISHENGLISH
| Owner’s Manual
blackstoneproducts.com/support
  BOX
Inside № 3 Box
30 Le front
side shelf bracket
(1 piece)
31 Right front
side shelf bracket
(1 piece)
32 Le rear
side shelf bracket
(1 piece)
33 Right rear
side shelf bracket
(1 piece)
34 Bottle
opener (1 piece)
35 Spacing
boards (3 pieces)
36 Faucet
support panel
(1 piece)
  BOX 37 Plastic nut
(1 piece)
38 Sink
(1 piece)
39 Seasoning
box holder (1 piece)
  BOX
Inside № 4 Box
40 Drawer
handles (2 pieces)
41 Door handle
(1 piece)
42 Faucet base
(1 piece)
43 Bottom
drawer face plate
(1 piece)
44 Plastic
water tube (1 piece)
45 Female sili-
cone ring (1 piece)
46 Male sili-
cone ring (1 piece)
47 Faucet
(1 piece)
48 Metal hooks
(4 pieces)
49 Faucet nut
(1 piece)
  BOX 50 Top drawer
(1 piece)
51 Seasoning
boxes (4 pieces)
52 Seasoning
box lids (4 pieces)
53 Small
drawers (2 pieces)
  BOX 54 LED button
assembly (1 piece)
55 LED strip
and battery pack
(1 piece)
03
Model 1948 Assembly Guide
ENGLISHENGLISH
Owner’s Manual |
blackstoneproducts.com/support
ENGLISH
TOOLS NEEDED: Phillips head screwdriver
& Adjustable wrench
TOOL NEEDED:
Phillips head screwdriver TOOL NEEDED:
Adjustable wrench
TOOLS NEEDED: Phillips head screwdriver
& Adjustable wrench
NOT INCLUDED:
Eight (8) AA Batteries
56 Hardware pack (1 piece)
a. M6x12 screws
(15 pieces) (17 pieces) (15 pieces)
b. M6x20 step bolts (12 pieces)
c. Shelf pegs (8 pieces)
d. Shelf peg washers (8 pieces)
e. Washers (2 pieces)
f. M4 Flange nuts (2 pieces)
g. Tapping screws (6 pieces)
h. M4x10 screws (17 pieces) (16 pieces)
56a
56a
56a
56b
56c
56d 56e
56f
56g
56h
56h
04
Model 1948Assembly Guide
ENGLISHENGLISH
| Owner’s Manual
blackstoneproducts.com/support
ENGLISH
!WARNING
The manufacturer has made
every eort to eliminate any
sharp edges. However, you
should handle all compo-
nents with care to avoid
accidental injury.
Some parts may contain
sharp edges, especially as
noted in these instructions.
Wear protective gloves if
necessary.
!WARNING
The use of alcohol, prescrip-
tion or non-prescription
drugs may impair the
consumers ability to prop-
erly assemble or safely
operate the appliance.
ASSEMBLY INSTRUCTIONS
Please read all instructions thoroughly before proceeding. Make sure all
the plastic packing material is removed before assembling.
Find a large, clean area to assemble your unit. Please refer to the parts list and
assembly diagrams as necessary.
ENGLISH
ASSEMBLY INSTRUCTIONS
Please read all instructions thoroughly before proceeding. Ensure
that all plastic packing material and any transit protection is removed
before assembling.
Find a large, clean area to assemble your unit. Please refer to the parts list and
assembly diagrams as necessary.
!WARNING
Do not mix old and new
batteries.
Do not mix alkaline, stan-
dard (carbon-zinc) or
rechargeable (ni-cad, ni-mh,
etc.) batteries.
!WARNING
Do not mix old and new
batteries.
Do not mix alkaline, stan-
dard (carbon-zinc) or
rechargeable (ni-cad, ni-mh,
etc.) batteries.
STEP  Use three (3) M4x10 (h.) screws to install the le leg assembly to
the bottom panel.
STEP  Remove the joint leg
assembly from the packaging.
Loosen the four (4) screws and sepa-
rate the le and right leg assemblies.
!CAUTION
Two people are recom-
mended for the assembly of
this product.
05
Model 1948 Assembly Guide
ENGLISHENGLISH
Owner’s Manual |
blackstoneproducts.com/support
STEP With the help of another person, set the cart on its back. Use
four (4) M6x12 screws (a.) to attach the two (2) xed wheels to the le leg
assembly. Use four (4) M6x12 screws (a.) to secure the right leg assembly to
the bottom panel, then insert the caster wheels into the right leg assembly.
STEP Use three (3) M4x10
screws (h.) to install the right leg
assembly to the bottom panel.
06
Model 1948Assembly Guide
ENGLISHENGLISH
| Owner’s Manual
blackstoneproducts.com/support
STEP  With the help of another person, set the cart on its feet and
use two (2) M6x12 (a.) screws to secure the xed wheels.
STEP Use three (3) M4x10 (h.) screws to attach the right rear panel to
right leg assembly and bottom panel.
07
Model 1948 Assembly Guide
ENGLISHENGLISH
Owner’s Manual |
blackstoneproducts.com/support
STEP  Use three (3) M4x10 screws (h.) to attach the le rear panel to the
le leg assembly and bottom panel. Use one (1) M4x10 screw (h.) to secure the
le rear panel to the right rear panel.
STEP  With the help of another person, place the table top on the
cart. Use four (4) M6x12 screws (a.) to secure the table to the le and right leg
assemblies (two (2) per side). Use two (2) M6x12 screws (a.) to secure the table
to the back panels.
08
Model 1948Assembly Guide
ENGLISHENGLISH
| Owner’s Manual
blackstoneproducts.com/support
STEP Use three (3) M4x10
screws (h.) to attach the center
drawer panel to the bottom panel.
Use two (2) M4x10 screws (h.) to
secure the middle drawer panel to
the rear panels.
STEP  Use six (6) M3 tapping screws (g.) to attach the three (3) spacing
boards to the top drawer panel.
09
Model 1948 Assembly Guide
ENGLISHENGLISH
Owner’s Manual |
blackstoneproducts.com/support
STEP  Align the center spacing board so that it inserts into the top slots
of the middle drawer panel. Use six (6) M4x10 screws (h.) to attach the top
drawer panel to the leg assemblies, and one (1) M4x10 screw (h.) to secure the
top drawer panel to the middle drawer panel.
Use two (2) M4x10 screws (h.) to
secure the top drawer panel to the
the rear panels.
10
Model 1948Assembly Guide
ENGLISHENGLISH
| Owner’s Manual
blackstoneproducts.com/support
STEP  Use two (2) M6x12
screws (a.) to attach one (1) door
handle to the right cart door.
STEP  Attach the right cart
door to the cart by rst inserting
the lower door hinge pin, then
inserting the upper door hinge pin.
STEP  Use two (2) M6x12
screws (a.) to attach one (1) drawer
handle to the lower drawer
front plate.
Use four (4) M4x10 screws (h.) to
attach the lower drawer front plate
to the lower drawer.
11
Model 1948 Assembly Guide
ENGLISHENGLISH
Owner’s Manual |
blackstoneproducts.com/support
STEP  Insert the plug in the pre-cut hole of the lower drawer.
Pull out the lower drawer rail.
Align the drawer rail between the lower drawer and the cart, and slide the
lower drawer into place.
STEP  Use two (2) M6x12 screws (a.) to attach one (1) drawer handle to
the upper drawer.
12
Model 1948Assembly Guide
ENGLISHENGLISH
| Owner’s Manual
blackstoneproducts.com/support
STEP  Pull out the upper drawer rail.
Align the drawer rail between the upper drawer and the cart, and slide the
upper drawer into place.
STEP  Tilt the four (4) small drawers and slide them into place.
13
Model 1948 Assembly Guide
ENGLISHENGLISH
Owner’s Manual |
blackstoneproducts.com/support
STEP  Use two (2) M6x12 screws (a.) to attach the paper towel bracket to
the le side of the cart.
STEP  Use one (1) M6x12 screw
(a.) and two (2) washers (e.) to
attach the paper tower holder onto
the paper towel bracket.
STEP Screw two (2) M6x20 step bolts (b.) into the lower holes of the
right leg assembly.
14
Model 1948Assembly Guide
ENGLISHENGLISH
| Owner’s Manual
blackstoneproducts.com/support
STEP  Use two (2) M6x20 step bolts (b.) to attach the garbage bag holder
to the right leg assembly.
STEP  Use seven (7) M6x12 screws (a.) to attach two (2) right side shelf
brackets to the right side of the cart.
STEP  Use seven (7) M6x12 screws (a.) to attach two (2) le side shelf
brackets to the le side of the cart.
15
Model 1948 Assembly Guide
ENGLISHENGLISH
Owner’s Manual |
blackstoneproducts.com/support
STEP  Hook the right side shelf bolts onto the side shelf brackets. Thread
two (2) M6x20 step bolts (b.) into the lower holes of the brackets to secure the
right side shelf to the shelf brackets.
STEP  Hook the le side shelf bolts onto the side shelf brackets. Thread
two (2) M6x20 step bolts (b.) into the lower holes of the brackets to secure the
le side shelf to the shelf brackets.
STEP  Thread two (2) M6x20 step bolts (b.) into the upper holes of the
right side shelf.
STEP  Use two (2) M6x12
screws (a.) to attach the faucet
support panel to the le side shelf.
Thread two (2) M6x20 step bolts
(b.) into the upper holes of the le
side shelf.
!CAUTION
Maximum weight on side
shelf is 10 lbs.
16
Model 1948Assembly Guide
ENGLISHENGLISH
| Owner’s Manual
blackstoneproducts.com/support
STEP  Attach the four (4) side shelf pegs (c.) and four (4) peg washers (d.)
to both side shelves by screwing them into the precut holes.
STEP  Install the inner gasket,
inner water output, lter and lter
cover into the bottom of the sink.
Set the outer gasket against the
bottom of the sink and screw the
outer water output into the inner
water output.
Use the plastic nut to attach the
plastic water tube to the outer
water output.
Filter cover
Filter
Inner water
output
Inner gasket
Outer gasket
Outer water
output
Plastic nut
Plastic water
tube
17
Model 1948 Assembly Guide
ENGLISHENGLISH
Owner’s Manual |
blackstoneproducts.com/support
STEP  Use two (2) M6x12
screws (a.) to attach the bottle
opener to the front of the right
leg assembly.
STEP  Attach the faucet base
and the female silicone ring onto
the bottom of the faucet.
Insert the faucet into the precut hole
of the faucet support panel, then
attach the male silicone ring and the
faucet nut to the end of the faucet.
STEP  Place the sink into the
le side shelf.
(Direct the plastic water tube into a
bucket, or other receptacle.)
Faucet base
Female
silicone ring
Male
silicone ring
Faucet nut
18
Model 1948Assembly Guide
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72

Blackstone 1948 Pro Series Prep/Serve and Store Cart Le manuel du propriétaire

Taper
Le manuel du propriétaire