MTD TB525CS Le manuel du propriétaire

Marque: MTD

Modèle: TB525CS

Catégorie: Coupe-herbe

Taper: Le manuel du propriétaire

Operator’s Manual

4-Cycle Gasoline Trimmer

TB575SS &

TB525CS

SAVE THESE INSTRUCTIONS

For service call 1-800-520-5520 to obtain a list of authorized

service dealers near you. For more details about your unit, visit

our website at www.troybilt.com.

DO NOT RETURN THE UNIT TO THE RETAILER. PROOF OF

PURCHASE WILL BE REQUIRED FOR WARRANTY

SERVICE.

THIS PRODUCT IS COVERED BY ONE OR MORE U.S.

PATENTS. OTHER PATENTS PENDING.

Service on this unit both within and after the warranty period

should be performed only by an authorized and approved

service dealer.

All information, illustrations, and specifications in this manual

are based on the latest product information available at the

time of printing. We reserve the right to make changes at any

time without notice.

WARNING: When using the unit, you must follow

the safety rules. Please read these instructions

before operating the unit in order to ensure the

safety of the operator and any bystanders. Please

keep these instructions for later use.

SPARK ARRESTOR NOTE

NOTE: For users on U.S. Forest Land and in the states of

California, Maine, Oregon and Washington. All U.S. Forest

Land and the state of California (Public Resources Codes 4442

and 4443), Oregon and Washington require, by law that certain

internal combustion engines operated on forest brush and/or

grass-covered areas be equipped with a spark arrestor,

maintained in effective working order, or the engine be

constructed, equipped and maintained for the prevention of

fire. Check with your state or local authorities for regulations

pertaining to these requirements. Failure to follow these

requirements could subject you to liability or a fine. This unit is

factory equipped with a spark arrestor. If it requires

replacement, ask your LOCAL SERVICE DEALER to install the

Accessory Part #753-05297 Spark Arrestor Kit.

CALIFORNIA PROPOSITION 65 WARNING

P/N 769-01920 (11/05)

TABLE OF CONTENTS

Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . . . . . . .2

Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Oil and Fuel Information . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Starting/Stopping Instructions . . . . . . . . . . . . . . . . . . . . . .5

Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Maintenance and Repair Instructions . . . . . . . . . . . . . . . .8

Cleaning and Storage . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E18

WARNING

THE ENGINE EXHAUST FROM THIS PRODUCT CONTAINS

CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO

CAUSE CANCER, BIRTH DEFECTS OR OTHER

REPRODUCTIVE HARM.

READ ALL INSTRUCTIONS BEFORE OPERATING

• Read the instructions carefully. Be familiar with the controls

and proper use of the unit.

• Do not operate this unit when tired, ill, or under the influence

of alcohol, drugs, or medication.

• Children and teens under the age of 15 must not use the

unit, except for teens guided by an adult.

• All guards and safety attachments must be installed properly

before operating the unit.

• Inspect the unit before use. Replace damaged parts. Check

for fuel leaks. Make sure all fasteners are in place and secure.

Replace parts that are cracked, chipped, or damaged in any

way. Do not operate the unit with loose or damaged parts.

• Carefully inspect the area before starting the unit. Remove

all debris and hard or sharp objects such as glass, wire, etc.

• Be aware of the risk of injury to the head, hands and feet.

• Clear the area of children, bystanders, and pets. At a minimum,

keep all children, bystanders, and pets outside a 50 feet (15

m.) radius; there still may be a risk to bystanders from thrown

objects. Bystanders should be encouraged to wear eye

protection. If you are approached, stop the unit immediately.

•U

se only 0.095 inch, 2.41 mm diameter original equipment

manufacturer replace-ment line. Never use metal-reinforced line, wire

or rope. These can break off and become dangerous projectiles.

• Squeeze the throttle control and check that it returns

automatically to the idle position. Make all adjustments or

repairs before using unit.

SAFETY WARNINGS FOR GAS UNITS

• Store fuel only in containers specifically designed and

approved for the storage of such materials.

• Avoid creating a source of ignition for spilled fuel. Do not

start the engine until fuel vapors dissipate.

• Always stop the engine and allow it to cool before filling the

fuel tank. Never remove the fuel tank cap or add fuel when

the engine is hot. Never operate the unit without the fuel cap

securely in place. Loosen the fuel tank cap slowly to relieve

any pressure in the tank.

• Add fuel in a clean, well-ventilated outdoor area where there

are no sparks or flames. Remove the fuel cap slowly, and

only after the engine stops. Do not smoke while fueling.

Wipe up any spilled fuel from the unit immediately.

• Avoid creating a source of ignition for spilled fuel. Do not

start the engine until fuel vapors dissipate.

•M

ove the unit at least 30 feet (9.1 m) from the fueling

source and site before starting the engine. Do not smoke.

Keep sparks and open flames away from the area while

adding fuel or operating the unit.

WHILE OPERATING

• Never start or run the unit inside a closed room or building.

Breathing exhaust fumes can be fatal. Operate this unit only

in a well-ventilated outdoor area.

• Wear safety glasses or goggles that meet ANSI Z87.1

standards and are marked as such. Wear ear/hearing

protection when operating this unit. Wear a face or dust

mask if the operation is dusty.

• Wear heavy long pants, boots, gloves and a long sleeve

shirt. Do not wear loose clothing, jewelry, short pants,

sandals or go barefoot. Secure hair above shoulder level.

• The cutting attachment shield must always be in place while

operating the unit as a trimmer. Do not operate unit without

both trimming lines extended, and the proper line installed.

Do not extend the trimming line beyond the length of the

shield.

• This unit has a clutch. The cutting attachment remains

stationary when the engine is idling. If it does not, have the

unit adjusted by an authorized service technician.

• Adjust the handle to your size in order to provide the best grip.

• Be sure the cutting attachment is not in contact with

anything before starting the unit.

• Use the unit only in daylight or good artificial light.

• Avoid accidental starting. Be in the starting position

whenever pulling the starter rope. The operator and unit

must be in a stable position while starting. Refer to

Starting/Stopping Instructions.

• Use the right tool. Only use this tool for its intended purpose.

• Do not overreach. Always keep proper footing and balance.

• Always hold the unit with both hands when operating. Keep

a firm grip on both handles or grips.

•K

eep hands, face, and feet at a distance from all moving parts.

Do not touch or try to stop the cutting attachment when it rotates.

• Do not touch the engine, gear housing or muffler. These

parts get extremely hot from operation, even after the unit is

turned off.

• Do not operate the engine faster than the speed needed to

cut, trim or edge. Do not run the engine at high speed when

not cutting.

• Always stop the engine when cutting is delayed or when

walking from one cutting location to another.

• If you strike or become entangled with a foreign object, stop

the engine immediately and check for damage. Do not

operate before repairing damage. Do not operate the unit

with loose or damaged parts.

• Stop the unit, switch the engine to off, and disconnect the

spark plug for maintenance or repair.

• Use only original equipment manufacturer replacement parts

and accessories for this unit. These are available from your

authorized service dealer. Use of any unauthorized parts or

accessories could lead to serious injury to the user, or damage

to the unit, and void your warranty.

• Keep unit clean of vegetation and other materials. They may

become lodged between the cutting attachment and shield.

• To reduce fire hazard, replace a faulty muffler and spark

arrestor. Keep the engine and muffler free from grass,

leaves, excessive grease or carbon build up.

After Use

• Clean cutting blades with a household cleaner to remove

any gum buildup. Oil the blade with machine oil to prevent

rust.

• Lock up and store the cutting blade in an appropriate area to

protect the blade from unauthorized use or damage.

OTHER SAFETY WARNINGS

• Never store a fueled unit inside a building where fumes may

reach an open flame or spark.

• Allow the engine to cool before storing or transporting. Be

sure to secure the unit while transporting.

• Store the unit in a dry area, locked up or up high to prevent

unauthorized use or damage, out of the reach of children.

• Never douse or squirt the unit with water or any other liquid.

Keep handles dry, clean and free from debris. Clean after

each use, see Cleaning and Storage instructions.

• Keep these instructions. Refer to them often and use them

to instruct other users. If you loan someone this unit, also

loan them these instructions.

SAVE THESE INSTRUCTIONS

RULES FOR SAFE OPERATION

• IMPORTANT SAFETY INSTRUCTIONS •

WARNING: Gasoline is highly flammable, and its

vapors can explode if ignited. Take the following

precautions:

RULES FOR SAFE OPERATION

SYMBOL MEANING

• WARNING - READ OPERATOR'S MANUAL

Read the operator’s manual(s) and follow all warnings

and safety instructions. Failure to do so can result in

serious injury to the operator and/or bystanders.

SAFETY AND INTERNATIONAL SYMBOLS

This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the

operator's manual for complete safety, assembly, operating and maintenance and repair information.

• ON/OFF STOP CONTROL

OFF or STOP

SYMBOL MEANING

• WEAR EYE AND HEARING PROTECTION

WARNING: Thrown objects and loud noise can

cause severe eye injury and hearing loss. Wear eye

protection meeting ANSI Z87.1 standards and ear

protection when operating this unit. Use a full face

shield when needed.

• KEEP BYSTANDERS AWAY

WARNING: Keep all bystanders, especially

children and pets, at least 50 feet (15 m) from the

operating area.

• THROWN OBJECTS AND ROTATING CUTTER

CAN CAUSE SEVERE INJURY

WARNING: Do not operate without the cutting

attachment shield in place. Keep away from the

rotating cutting attachment.

• HOT SURFACE WARNING

Do not touch a hot muffler, gear housing or cylinder.

You may get burned. These parts get extremely hot

from operation. They remain hot for a short time after

the unit is turned off.

• UNLEADED FUEL

Always use clean, fresh unleaded fuel

• OIL

Refer to operator’s manual for the proper type of

oil.

• SHARP BLADE

WARNING: Sharp blade on cutting attachment

shield. To prevent serious injury, do not touch the

line cutting blade.

• CHOKE CONTROL

1. • FULL choke position

2. • PARTIAL choke position

3. • RUN choke position

• ON/OFF STOP CONTROL

ON / START / RUN

• SAFETY ALERT SYMBOL

Indicates danger, warning or caution. May be used

in conjunction with other symbols or pictographs.

Cutting

Attachment Shield

Fuel

Cap

Throttle

Control

D-Handle

Cutting

Attachment

Shaft Grip

Primer

Bulb

Oil Fill Plug

Choke

Lever

Spark

Plug

Shaft

Starter

Rope

Grip

Line

Cutting

Blade

Muffler

Click Link

On/Off Stop

Control

KNOW YOUR UNIT

Air Filter

Cover

TB525CS &

TB575SS

ASSEMBLY INSTRUCTIONS

INSTALLING AND ADJUSTING THE D-HANDLE

If your unit has the D-Handle pre-installed, please follow the

“To Adjust” instructions only.

To Install

1. Remove the screws and

bottom clamp piece that

were installed on the D-

handle for shipping.

2. Place the D-handle over

the shaft housing and

onto the bottom clamp

(Fig. 1). Place it a

minimum of 15.24 cm (6

in) from the end of the

shaft grip.

3. Start screws with a large Flat-head or T-25 Torx

screwdriver. Do not tighten until you make the handle

adjustment.

To Adjust

4. If the D-handle was pre-installed, loosen the screws on the

handle just enough to move it.

5. While holding the unit in the operating position, manuever

the D-handle to the location that provides you the best grip

(Fig. 12).

6. Tighten the clamp screws evenly, until the D-handle is

secure.

(4) Screws

D-Handle

Bottom

Clamp

Fig. 1

Minimum

6 inches

(15.24 cm)

RECOMMENDED OIL TYPE

Using the proper type and weight of oil in the crankcase is

extremely important. Check the oil before each use and change

the oil regularly. Failure to use the correct oil, or using dirty oil,

can cause premature engine wear and failure.

Use a high-quality SAE 30 weight oil of API (American Petroleum

Institute) service class SF, SG, SH.

ADDING OIL TO CRANKCASE: INITIAL USE

NOTE: This unit is shipped

without oil. In order to avoid

damage to the unit, put oil in

the crankcase before you

attempt to start the unit.

Your unit is supplied with one 3.04

fluid oz. (90 ml.) bottle of SAE 30

SF, SG, SH oil (Fig. 2).

NOTE: Save the bottle of oil. It can

be used to measure the correct amount during future oil

changes. See Changing the Oil.

1. Unscrew the top of the

bottle of oil and remove the

paper seal covering the

opening. Replace the top.

Next, cut the tip off the

funnel spout (Fig. 2).

2. Tip unit so that the back of

the engine is facing up in a

vertical position.

3. Remove the oil fill plug from the crankcase (Fig. 3).

4. P

our the entire bottle of oil

into the oil fill hole (Fig. 4).

NOTE: Never add oil to the fuel

or fuel tank.

5. Wipe up any oil that may

have spilled and reinstall the

oil fill plug.

Check oil before each use and

change as needed. Refer to

Checking the Oil Level.

WARNING: OVERFILLING OIL CRANKCASE MAY

CAUSE SERIOUS PERSONAL INJURY. Check and

maintain the proper oil level in the crank case; it is

important and cannot be overemphasized. Check

the oil before each use and change it as needed.

See Changing the Oil.

Fig. 2

Funnel

Spout

RECOMMENDED FUEL TYPE

Old fuel is the primary reason for improper unit performance.

Be sure to use fresh, clean, unleaded gasoline.

NOTE: This is a four cycle engine. In order to avoid damage to

the unit, do not mix oil with gasoline.

Definition of Blended Fuels

Today's fuels are often a blend of gasoline and oxygenates

such as ethanol, methanol or MTBE (ether). Alcohol-blended

fuel absorbs water. As little as 1% water in the fuel can make

fuel and oil separate or form acids when stored. Use fresh fuel

(less than 60 days old), when using alcohol-blended fuel.

Using Blended Fuels

If you choose to use a blended fuel, or its use is unavoidable,

follow recommended precautions:

• Always use fresh unleaded gasoline

• Use the fuel additive STA-BIL® or an equivalent

• Drain tank and run the engine dry before storing unit

Using Fuel Additives

The use of fuel additives, such as STA-BIL® Gas Stabilizer or

an equivalent, will inhibit corrosion and minimize the formation

of gum deposits. Using a fuel additive can keep fuel from

forming harmful deposits in the carburetor for up to six (6)

months. Add 0.8 oz. (23 ml.) of fuel additive per gallon of fuel

according to the instructions on the container. NEVER add fuel

additives directly to the unit's gas tank.

FUELING THE UNIT

1. Remove the fuel cap (Fig. 5).

2. Place the gas container’s spout into the fill hole on the fuel

tank (Fig. 5) and fill the tank.

NOTE: Do not overfill the tank.

3. Wipe up any gasoline that may have spilled.

4. Reinstall the fuel cap.

5. Move the unit at least 30 ft. (9.1 m) from the fueling source

and site before starting the engine.

NOTE: Dispose of the old gasoline in accordance to Federal,

State and Local regulations.

Oil Fill Plug

Oil Fill Hole

O-Ring

WARNING: Add fuel in a clean, well ventilated

outdoor area. Wipe up any spilled fuel immediately.

Avoid creating a source of ignition for spilt fuel. Do

not start the engine until fuel vapors dissipate.

WARNING: Gasoline is extremely flammable.

Ignited vapors may explode. Always stop the engine

and allow it to cool before filling the fuel tank. Do

not smoke while filling the tank. Keep sparks and

open flames at a distance from the area.

WARNING: Remove fuel cap slowly to avoid injury

from fuel spray. Never operate the unit without the

fuel cap securely in place.

Fig. 5

Fuel Cap

Fuel Tank

Gas Can Spout

WARNING: To avoid serious personal injury, the

cutting attachment shield MUST be in place at all

times while operating the unit as a trimmer.

Fig. 4

Fig. 3

OIL AND FUEL INFORMATION

Start/On (I)

Stop/Off (O)

Throttle Control

Fig. 6

STARTING INSTRUCTIONS

STOPPING INSTRUCTIONS

1. Release your hand from the throttle control. Allow the

engine to cool down by idling.

2. Press the On/Off Stop Control switch in the OFF (O)

position.

1. Check the oil level in the crankcase. Refer to

Checking the Oil Level.

2. Fill the fuel tank with fresh, clean unleaded gasoline.

Refer to Fueling the Unit.

3. Make sure the On/Off Stop Control in the ON ( I )

position (Fig. 6).

4. Fully press and release the primer bulb 10 times,

slowly. Some amount of fuel should be visible in

the primer bulb and fuel lines (Fig. 7). If you can’t

see fuel in the bulb, press and release the bulb as

many times as it takes before you can see fuel in it.

5. Place the choke lever in Position 1 (Fig. 7).

6. Crouch in the starting position (Fig. 8). Squeeze the

throttle control lever. Pull the starter rope briskly 5

times.

7. Place the choke lever in Position 2 (Fig. 7).

8. While squeezing the throttle control , pull the starter

rope briskly 1 to 4 times to start the engine.

9. Keep the throttle squeezed and allow the engine to

warm up for 15 to 30 seconds.

10. Place the choke lever in Position 3 (Fig. 7). The unit

is ready for use.

IF...

The engine does not start, go back to step 4.

IF...

The engine fails to start after a few attempts, place

the choke lever in Position 3 and squeeze the

throttle control. Pull the starter rope briskly 3 to 8

times. The engine should start. If not, repeat.

WARNING: Avoid accidental starting. Make sure

you are in the starting position when pulling the

starter rope (Fig. 8). To avoid serious injury, the

operator and unit must be in a stable position while

starting.

To avoid serious personal injury, ensure any Add-

On being used is installed correctly and secure

before starting the unit.

WARNING: Operate this unit only in a well-

ventilated outdoor area. Carbon monoxide exhaust

fumes can be lethal in a confined area.

Starter Rope

Throttle Control

Fig. 8

Primer Bulb

Fig. 7

Choke Lever

APPLICATIONS

As a trimmer:

• Cutting grass and light weeds

• Edging

• Decorative trimming around trees, fences, etc.

STARTING/STOPPING INSTRUCTIONS

For edging (when using the line head cutting attachment with

EZ-Link™ models), lock the release button of the cutting

attachment into the 90° edging hole (Fig. 11).

OPERATING THE EZ-LINK™ SYSTEM

The EZ-Link™ system enables the use of these optional Add-

Ons:

Cultivator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBGC

Edger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBLE

Hedge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBAH

Straight Shaft Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . TBSS

Turbo Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBTB

Pole Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBPS

Brushcutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TBBC*

*Do NOT use this attachment with an electric powered unit.

Removing the Cutting Attachment or Add-On

1. Turn the knob counterclockwise to loosen (Fig. 9).

2. Press and hold the release button (Fig. 9).

3. While firmly holding the upper shaft housing, pull the

cutting attachment or add-on straight out of the EZ-Link™

coupler (Fig. 10).

Installing the Cutting Attachment or Add-On

NOTE: Place the unit on the ground or on a work bench to

make add-on installation or removal easier.

1. Turn knob counterclockwise to loosen (Fig. 9).

Fig. 9

EZ-Link™ Coupler

Release Button

Guide Recess

Knob

Primary Hole

Upper Shaft Housing

EZ-Link™ Coupler

2. While firmly holding the add-on, push it straight into the

EZ-Link™ coupler (Fig. 10).

NOTE: Aligning the release button with the guide recess will

help installation (Fig. 9).

3. Turn the knob clockwise to tighten (Fig. 11).

Fig. 10

Fig. 11

Knob

Lower Shaft Housing

Release Button

90˚ Edging Hole

(Trimmer Only)

OPERATING INSTRUCTIONS

WARNING: Before you begin using any

attachment, read and understand the manual that

came with the attachment. Follow all safety

information contained within.

WARNING: To avoid serious personal injury and

damage to the unit, shut the unit off before

removing or installing add-ons.

CAUTION: Lock the release button in the primary

hole and securely tighten the knob before operating

this unit.

CAUTION: Add-ons are to be used in the primary

hole only. Using the wrong hole could lead to

personal injury or damage to the unit.

HOLDING THE TRIMMER

Before operating the unit, stand in

the operating position (Fig. 12).

Check for the following:

• The operator is wearing eye

protection and proper clothing

• With a slightly-bent right arm, the

operator’s right hand is holding the

shaft grip

• The operator’s left arm is straight,

the left hand holding the assist

handle

• The unit is at waist level

• The cutting attachment is parallel to

the ground and easily contacts the

grass without the need to bend over

ADJUSTING TRIMMING LINE LENGTH

The Bump Head™ cutting attachment allows you to release

trimming line without stopping the engine. To release more line,

lightly tap the cutting attachment on the ground (Fig. 13) while

operating the trimmer at high speed.

NOTE: Always keep the trimming line fully extended. Line release

becomes more

difficult as the cutting

line becomes shorter.

Each time the head is

bumped, about 1 inch

(25.4 mm) of trimming

line is released. A blade

in the cutting attachment

shield will cut the line to

the proper length if

excess line is released.

For best results, tap the Bump Head™ on bare ground or hard

soil. If line release is attempted in tall grass, the engine may

stall. Always keep the trimming line fully extended. Line release

becomes more difficult as the cutting line becomes shorter.

NOTE: Do not rest the Bump Head™ on the ground while the

unit is running.

Some line breakage will occur from:

• Entanglement with foreign matter

• Normal line fatigue

• Attempting to cut thick, stalky weeds

• Forcing the line into objects such as walls or fence posts

TIPS FOR BEST TRIMMING RESULTS

• For best trimming results, operate unit at full throttle.

• Keep the cutting attachment parallel to the ground.

• Do not force the cutting attachment. Allow the tip of the line to do

the cutting, especially along walls. Cutting with more than the tip

will reduce cutting efficiency and may overload the engine.

• Cut grass over 8 inches (200 mm) by working from top to bottom

in small increments to avoid premature line wear or engine drag.

• Cutting from right to left improves the unit's cutting efficiency.

Clippings are thrown away from the operator.

• Slowly move the trimmer into and out of the cutting area at the

desired height. Move either in a forward-backward or side-to-

side motion. Cutting shorter lengths produces the best results.

• Trim only when grass and weeds are dry.

• The life of your cutting line is dependent upon proper

adherence of explained trimming techniques, what

vegetation is cut, and where vegetation is cut.

For example, the line will wear faster when trimming against a

foundation wall as opposed to trimming around a tree.

DECORATIVE TRIMMING

Decorative trimming is

accomplished by removing all

vegetation around trees, posts,

fences and more.

Rotate the whole unit so that the

cutting attachment is at a 30°

angle to the ground (Fig. 14).

OPERATING INSTRUCTIONS

WARNING: Do not remove or alter the line cutting

blade assembly. Excessive line length will make the

clutch overheat. This may lead to serious personal

injury or damage to the unit.

WARNING: Always wear eye, hearing, foot and

body protection to reduce the risk of injury when

operating this unit.

Fig. 12

Fig. 14

Fig. 13

WARNING: To prevent serious injury, never

perform maintenance or repairs with unit running.

Always service and repair a cool unit. Disconnect the

spark plug wire to ensure that the unit cannot start.

FREQUENCY MAINTENANCE REQUIRED SEE

Before starting engine

Fill fuel tank with fresh fuel

Check oil

p. 4

p. 9

Every 10 hours Clean and re-oil air filter p. 10

1st change at 10 hours

2nd change at 25 hours

Every 25 hours after

Change oil

Clean spark arrestor

p. 10

p. 13

10 hours on new engine

Every 25 hours

Check rocker arm to valve clearance and adjust

Check spark plug condition and gap

p. 11

p. 12

MAINTENANCE AND REPAIR INSTRUCTIONS

MAINTENANCE SCHEDULE

Perform these required maintenance procedures at the

frequency stated in the table. These procedures should also be

a part of any seasonal tune-up.

NOTE: Some maintenance procedures may require special

tools or skills. If you are unsure about these

procedures take your unit to any non-road engine

repair establishment, individual or authorized service

dealer.

SPEEDSPOOL

LINE INSTALLATION

Always use original equipment manufacturer 0.095 inch

(2.41 mm) replacement line. Lines other than those specified

may make the engine overheat or fail.

There are two methods to replace the SpeedSpool® trimming

line:

• Wind the inner reel with new line

• Install a pre-wound inner reel

Winding the Inner Reel With New Line

NOTE: It Is unnecessary to remove the bump knob to install a

new trimming line.

1. Cut two pieces of

0.095 inch

(2.41 mm)

trimming line, 10

feet (3 m) long.

2. Hold the outer

spool and turn the

inner reel

counterclockwise

to line up the

arrows on the

outer spool and

inner reel (Fig. 15).

3. Pull old line out of the line

loading and line locking holes

(Fig. 17 and 18).

4. Insert a piece of trimming line

straight into one of the two

eyelets in the outer spool.

Push it up through the line

loading hole in the inner reel

(Fig. 16). Do not bend the line

when inserting it into the

eyelet.

5. Insert the line into the locking

hole (Fig. 17). Do not push the

line more than a 1/2 inch (12.7

mm) into the line locking hole. The line will form a small

loop (Fig. 17) when it is inserted correctly.

6. Pull the line from the outer spool until the line is tight

against the inner reel (Fig. 18).

7. Repeat procedures 4-6 with the second piece of line.

8. Hold the outer spool. Wind the inner reel counterclockwise

until approximately four (4) inches (102 mm) of line remain

(Fig. 19).

Fig. 18

WARNING: Never use metal-reinforced line, wire,

chain or rope. These can break off and become

dangerous projectiles.

WARNING: Always use the correct line length

when installing trimming line on the unit. The line

may not release properly if the line is too long.

Top View Of The SpeedSpool®

Outer Spool

Inner Reel

Bump Knob

Arrows

Fig. 15

Trimming

Line

Line Loading Hole

Eyelet

Fig. 16

Line Locking Hole

Fig. 17

NOTE: Maintenance, replacement, or repair of the emission

control devices and system may be performed by any

non-road engine repair establishment, individual or

authorized service dealer.

In order to assure peak performance of your engine, inspection

of the engine exhaust port may be necessary after 50 hours of

operation. If you notice lost RPM, poor performance or general

lack of acceleration, this service may be required. If you feel

your engine is in need of this inspection, refer service to any

non-road engine repair establishment, individual or authorized

service dealer for repair. DO NOT attempt to perform this

process yourself as engine damage may result from

contaminants involved in the cleaning process for the port.

NOTE: The inner reel must be totally

dry before reinstalling it into

the outer spool. Do not

lubricate the inner reel or

outer spool assembly.

6. Place the inner reel into the outer

spool.

7. Place the bump knob, spring

and foam seal into the inner reel

(Fig. 22).

8. Press the bump knob down and

tighten clockwise.

9. Install new line as

described in Line

Installation for the

SpeedSpool

MAINTENANCE AND REPAIR INSTRUCTIONS

9. If winding the line becomes

difficult or if the line jams,

pull the ends of the line from

the spool (Fig. 19). Continue

winding the inner reel

counterclockwise until

approximately 6 inches of

line is left.

INSTALLING A PRE-WOUND

REEL

1. T

urn the bump knob

counterclockwise and

remove the bump knob,

spring and foam seal

(Fig. 20).

2. Pull the old inner reel

with existing line from

the outer spool.

3. Insert the ends of the

prewound inner reel line

into the outer spool eyelets (Fig. 21).

Push the new inner reel, arrow side

up, into the outer spool.

4. H

old the inner reel in place and

install the bump knob, spring and

foam seal (Fig. 22). Press down and

turn the bump knob clockwise.

Grasp the ends and pull firmly to

release the line from the holding slots

in the inner reel.

Releasing the Inner Reel

If the SpeedSpool

does not

release line correctly, pull the

ends of the line firmly from the

spool (Fig. 18). If this does not

the release line, follow the

Cleaning the SpeedSpool

instructions.

NOTE: Do not wind the inner

reel before installing

the second piece of

line.

CLEANING THE

SPEEDSPOOL

Cleaning the SpeedSpool

may

be necessary if:

• A jammed or excessive line must be removed

• The SpeedSpool

becomes difficult to wind or does not

operate correctly when bumping the head on the ground

1. Hold the outer spool, and unscrew the bump knob

counterclockwise (Fig. 23).

2. Pull out the bump knob, spring and foam

seal (Fig. 22).

3. P

ull the inner reel with existing line from the

outer spool (Fig. 24).

4. Remove any existing line from the inner

reel before cleaning. Remove any debris or

grass from the knob, spring, inner reel and

foam seal. Wash the inner reel with warm

soapy water (Fig. 24).

5. Clean the shaft and the inner surface of the outer spool. To

clean the shaft underneath the plunger, press down on the

plunger (Fig. 25). Remove any dirt or debris from the shaft.

Fig. 19

Fig. 20

Bump Knob

Foam Seal

Spring

Inner Reel

Fig. 22

Fig. 21

Fig. 23

Fig. 24

Inner Reel

CHECKING THE OIL LEVEL

The importance of checking

and maintaining the proper

oil level in the crankcase

cannot be overemphasized.

Check oil before each use:

1. Stop the engine and allow oil to drain into the crankcase.

2. Place the engine on a flat, level surface with the cutting

head shield hanging off a work bench or table to get a

proper oil level reading (Fig. 26).

3. Keep dirt, grass clippings and other debris out of the engine.

Clean the area around the dipstick before removing it.

4. Remove the oil fill plug.

5. Look into the oil fill hole, use a flashlight if needed. The oil

should be just touching the inner most thread (Fig. 27).

6. If the oil level is not touching the inner most thread on the

oil fill hole, add a small amount of oil to the oil fill hole and

recheck (Fig. 27). Repeat this procedure until the oil level

reaches the inner most thread on the oil fill hole.

NOTE: Do not overfill the unit.

NOTE: Make sure the O-ring is in place on the oil fill plug when

checking and changing the oil (Fig. 28).

Fig. 26

Oil Fill Plug

Oil Fill Hole

O-Ring

MaxOil Fill Line

Fig. 28

Fig. 27

Shaft

Plunger

Fig. 25

MAINTENANCE AND REPAIR INSTRUCTIONS

CHANGING THE OIL

For a new engine, change the oil after the first 10 hours of

operation. Change the oil while the engine is still warm. The oil will

flow freely and carry away more impurities.

1. Unplug spark plug boot to prevent accidental starting.

2. Remove the oil fill plug.

3. Pour the oil out of the

oil fill hole and into a

container by tipping the

unit to a vertical

position (Fig. 29). Allow

ample time for

complete drainage.

4. Wipe up any oil residue

on the unit and clean

up any oil that may

have spilled. Dispose of

the oil according to

Federal, State and local

regulations.

5. Refill the crankcase

with 3.04 fluid ounce

(90 ml) of SAE 30 SF, SG, SH oil.

NOTE: Use the bottle and spout saved from initial use to measure

the correct amount of oil. The top of the label on the bottle

measures approximately 3.04 ounces (90 ml) (Fig. 30). Check

the level, See Checking the Oil Level. If the level is low, add a

small amount of oil and recheck. Do not overfill (Fig. 30).

6. Replace the oil fill plug.

7. Reconnect the spark plug boot.

AIR FILTER MAINTENANCE

Cleaning the Air Filter

Clean and re-oil the air filter every 10 hours of operation. It is

an important item to maintain. Failure to maintain your air filter

properly can result in poor performance or can cause

permanent damage to your engine.

1. Open the air filter cover. Push the tab on the under side of

the cover inward. Then pull the air filter cover out and up.

(Fig. 31).

WARNING: Wear gloves to prevent injury when

handling unit.

Fig. 29

Fill Level

Fig. 30

2. Remove the air filter (Fig. 31).

3. Wash the filter in detergent and

water (Fig. 32). Rinse the filter

thoroughly and allow it to dry.

4. Apply enough clean SAE 30

motor oil to lightly coat the filter

(Fig. 33).

5. Squeeze the filter to spread and

remove excess oil (Fig. 34).

6. Replace the filter (Fig. 31).

NOTE: If the unit is operated

without the air filter, you will

VOID the warranty.

7. Reinstall the air filter cover. Position the slots on the top of

the air filter cover onto the tabs at the top of the back plate

(Fig. 35).

8. Swing the cover down until the tab on the air filter backplate

snaps into place in the slot on the air filter cover (Fig. 36).

WARNING: To avoid serious personal injury,

always turn the unit off and allow it to cool before

you clean or service it.

Fig. 32

Air Filter Cover

Air Filter

Tab

Fig. 31

Fig. 33

Fig. 34

Fig. 35

Locking Tab

Tabs

Back Plate

Air Filter

Checking the fuel, cleaning the air filter, and adjusting the idle

speed should solve most engine problems. If not and all of the

following are true:

• the engine will not idle

• the engine hesitates or stalls on acceleration

• there is a loss of engine power

Have the carburetor adjusted by an authorized service dealer.

ROCKER ARM CLEARANCE

This requires disassembly of the engine. If you feel unsure or

unqualified to perform this, take the unit to an authorized

service center.

NOTE: Inspect the valve to rocker arm clearance with a feeler

gauge after the first 10 hours of operation and every 25

hours of operation.

• The engine must be cold when checking or adjusting the

valve clearance.

• This task should be performed inside, in a clean, dust free

area.

1. Remove the six (6) screws on the back of the engine cover

with a Flat-head or T-25 Torx screwdriver (Fig. 38).

2. Disconnect the spark plug wire.

3. Clean dirt from around the spark plug. Remove the spark

plug from the cylinder head by turning a 5/8 in. socket

counterclockwise.

4. Remove the engine cover (Fig. 38).

5. Clean dirt from around the rocker arm cover. Remove the

screw holding the rocker arm cover with a large flat blade

screwdriver or Torx T-25 bit (Fig. 39). Remove the rocker

arm cover and gasket.

6. Pull the starter rope slowly to

bring the piston to the top of its

travel, (known as top dead

center). Check that:

• The piston is at the top of its

travel while looking in the

spark plug hole (Fig. 40)

• Both rocker arms move

freely, and both valves are

CARBURETOR ADJUSTMENT

The idle speed of the engine is adjustable. An idle adjustment

screw is between the air filter cover and the engine starter

housing (Fig. 37).

NOTE: Careless

adjustments can

seriously damage your

unit. An authorized

service dealer should

make carburetor

adjustments.

Check Fuel

Old fuel is usually the

reason for improper unit

performance. Drain and

refill the tank with fresh fuel

prior to making any adjustments. Refer to Oil and Fuel

Information.

Clean Air Filter

The condition of the air filter is important to the operation of the

unit. A dirty air filter will restrict air flow. This is often mistaken

for an out of adjustment carburetor. Check the condition of the

air filter before adjusting the idle speed screw. Refer to Air

Filter Maintenance.

Adjust Idle Speed Screw

If, after checking the fuel and cleaning the air filter, the engine

still will not idle, adjust the idle speed screw as follows:

1. Start the engine and let it run at a high idle for a minute to

warm up. Refer to Starting/Stopping Instructions.

2. Release the throttle trigger and let the engine idle. If the

engine stops, insert a small phillips in between the Air Filter

Cover and the Engine Cover (Fig. 48). Turn the idle speed

screw in, clockwise, 1/8 of a turn at a time (as needed) until

the engine idles smoothly.

NOTE: The cutting attachment should not rotate when the

engine idles.

3. If the cutting attachment rotates when the engine idles, turn

the idle speed screw counterclockwise 1/8 of a turn at a

time (as needed), to reduce idle speed.

MAINTENANCE AND REPAIR INSTRUCTIONS

WARNING: The cutting attachment may spin during

idle speed adjustments. Wear protective clothing and

observe all safety instructions to prevent serious

personal injury.

WARNING: To prevent serious personal injury,

make sure the cutting attachment has stopped

rotating before you turn it off and set it down.

Idle Adjustment Screw

Fig. 37

Remove

Screws

Fig. 38

View Of The Rear Engine Cover

Rocker

Arm

Cover

Fig. 39

Spark

Plug

Hole

Air Filter Cover

Air Filter

Tab

Fig. 36

Remove

Screws

closed

If these statements are not true, repeat this step.

7. Slide the feeler gauge between the rocker arm and the

valve return spring. Measure the clearance between the

valve stem and rocker arm (Fig. 40). Measure both the

intake and exhaust valves.

The recommended clearance for both intake and exhaust is

.003 – .006 in. (.076 – 0.152 mm). Use a standard automotive

.005 in. (0.127 mm) feeler gauge. The feeler gauge should slide

between the rocker arm and valve stem with a slight amount of

resistance, without binding. See Figures 40 and 41.

8. If the clearance is not within specification:

a. Turn the adjusting nut using a 5/16 inch (8 mm) wrench or

nut driver (Fig. 40).

• To increase clearance, turn the adjusting nut

counterclockwise.

• To decrease clearance, turn the adjusting nut

clockwise.

b. Recheck both clearances, and adjust as necessary.

9. Reinstall the rocker arm cover using a new gasket. Torque

the screw to 20–30 in•lb (2.2–3.4 N•m).

10. Check the spark plug and reinstall. See Replacing the

Spark Plug.

11. Replace the spark plug wire.

MAINTENANCE AND REPAIR INSTRUCTIONS

Fig. 41

12. Reinstall the engine cover. Check alignment of the cover

before tightening the screws. Tighten screws.

REPLACING THE SPARK PLUG

Use a replacement part number 753-05255 spark plug. The

correct air gap is 0.025 in. (0.655 mm.). Remove the plug after

every 25 hours of operation and check its condition.

1. Stop the engine and allow it to cool. Remove the six (6)

screws on the back of the engine cover with a Flat-head or

T-25 Torx screwdriver (Fig. 38).

2. Grasp the plug wire firmly and pull the cap from the spark

plug.

3. Clean dirt from around the

spark plug. Remove the

spark plug from the cylinder

head by turning a 5/8 in.

socket counterclockwise.

4. Replace cracked, fouled or

dirty spark plug. Set the air

gap at 0.025 in. (0.655 mm.)

using a feeler gauge (Fig. 42).

5. Install a correctly-gapped

spark plug in the cylinder head. Turn the 5/8 in. socket

clockwise until snug.

If using a torque wrench torque to:

Feeler Gauge

Adjusting Nut

Rocker Arm

.003–.006 in.

(.076–.152 mm)

Valve Stem

Adjusting Nuts

Feeler Gauge

Rocker Arms

Fig. 40

INTAKE

EXHAUST

0.025 in.

(0.655 mm.)

Fig. 42

WARNING: Do not sand blast, scrape or clean

electrodes. Grit in the engine could damage the

cylinder.

Spark Plug

Hole

SPARK ARRESTOR MAINTENANCE

1. Remove the rear engine cover. See Rocker Arm Clearance.

2. With a flat blade screwdriver or Torx T-20 bit and a T-25

bit, remove the screws attaching the spark arrestor cover

to the muffler (Fig. 43).

3. Pull the tab on the spark arrestor cover out of the muffler.

Remove the spark arrestor cover.

4. Remove the spark arrestor screen from the spark arrestor

cover.

5. Clean the spark arrestor screen with a wire brush or

replace it.

6. Reinstall the spark arrestor screen, spark arrestor cover

and screws.

CLEANING

Use a small brush to clean off the outside of the unit. Do not

use strong detergents. Household cleaners that contain

aromatic oils such as pine and lemon, and solvents such as

kerosene, can damage plastic housing or handle. Wipe off any

moisture with a soft cloth.

STORAGE

• Never store the unit with fuel in the tank where fumes may

reach an open flame or spark.

• Allow the engine to cool before storing.

• Lock up the unit to prevent unauthorized use or damage.

• Store the unit in a dry, well-ventilated area.

• Store the unit out of the reach of children.

LONG TERM STORAGE

1. Drain all gasoline from the gas tank into a container. Do

not use gas that has been stored for more than 60 days.

Dispose of the old gasoline in accordance to Federal,

State, and Local regulations.

2. Start the engine and allow it to run until it stalls. This

ensures that all gasoline has been drained from the

carburetor.

3. Allow the engine to cool. Remove the spark plug and put 1

oz. (30 ml) of high quality motor oil into the cylinder. Pull

the starter rope slowly to distribute the oil. Reinstall the

spark plug.

NOTE: Remove the spark plug and drain all of the oil from the

cylinder before attempting to start the trimmer after

storage.

4. Change the oil, referring to Changing the Oil. Dispose of

the old oil in accordance to Federal, State and Local

regulations.

5. Thoroughly clean the unit and inspect for any loose or

damaged parts. Repair or replace damaged parts and

tighten loose screws, nuts or bolts. The unit is ready for

storage.

TRANSPORTING

• Allow the engine to cool before transporting.

• Secure the unit while transporting.

• Drain the gas tank before transporting.

• Tighten gas cap before transporting.

MAINTENANCE AND REPAIR INSTRUCTIONS

WARNING: To avoid serious personal injury,

always turn your unit off and allow it to cool before

you clean or service it.

Fig. 43

Muffler

Spark Arrestor Screen

Diverter

T-20 Screw

Slot

T-25 Screw

TROUBLESHOOTING

If further assistance is required, contact your authorized service dealer.

CAUSE ACTION

Cutting attachment bound with grass Stop the engine and clean cutting attachment

Cutting attachment out of line Refill with new line

Inner reel bound up Replace the inner reel

Cutting head dirty Clean inner reel and outer spool

Line welded Disassemble, remove the welded section and rewind

Line twisted when refilled Disassemble and rewind the line

Not enough line is exposed Push the bump knob and pull out line until 4 inches (102 mm)

of line is outside of the cutting attachment

CAUSE ACTION

Old fuel Drain gas tank and add fresh fuel

Improper carburetor adjustment Take to an authorized service dealer for adjustment

Fouled spark plug Replace or clean the spark plug

Plugged spark arrestor Clean or replace spark arrestor

CAUSE ACTION

On/Off control in the STOP position

Turn On/Off control to ON

Empty fuel tank Fill fuel tank with new fuel

Primer bulb wasn't pressed enough Press primer bulb fully and slowly 10 times

Old fuel Drain gas tank and add fresh fuel

Fouled spark plug Replace or clean the spark plug

Plugged spark arrestor Clean or replace spark arrestor

ENGINE WILL NOT START

ENGINE WILL NOT IDLE

ENGINE WILL NOT ACCELERATE

ENGINE LACKS POWER OR STALLS WHEN CUTTING

CAUSE ACTION

Air filter is plugged Replace or clean the air filter

Old fuel Drain gas tank and add fresh fuel

Improper carburetor adjustment Adjust carburetor

CAUSE ACTION

Old fuel Drain gas tank and add fresh fuel

Improper carburetor adjustment Take to an authorized service dealer for adjustment

Cutting attachment bound with grass Stop the engine and clean the cutting attachment

Dirty air filter Clean or replace the air filter

Plugged spark arrestor Clean or replace spark arrestor

CUTTING ATTACHMENT WILL NOT ADVANCE LINE

CAUSE ACTION

Oil, cleaner or lubricant in cutting head Clean and thoroughly dry the cutting head

CUTTING LINE ADVANCES UNCONTROLLABLY

SPECIFICATIONS

ENGINE*

DRIVE SHAFT AND CUTTING ATTACHMENT*

*All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes

at any time without notice.

Engine Type ......................................................................................................................................................................................... Air-Cooled, 4-Cycle

Displacement............................................................................................................................................................................................ 1.8 cu. in. (29 cc)

Operating RPM................................................................................................................................................................................................... 6,800+ rpm

Idle Speed RPM ...................................................................................................................................................................................... 2,800 - 3,600 rpm

Ignition Type ......................................................................................................................................................................................................... Electronic

Ignition Switch ............................................................................................................................................................................................... Rocker Switch

Valve clearance.............................................................................................................................................................. 0.003–0.006 in. (0.076–0.152 mm)

Spark Plug Gap ................................................................................................................................................................................ 0.025 inch (0.655 mm)

Lubrication ........................................................................................................................................................................................................... SAE 30 Oil

Crankcase Oil Capacity................................................................................................................................................................................ 3.04 oz (90 ml)

Fuel....................................................................................................................................................................................................................... Unleaded

Carburetor....................................................................................................................................................................................... Diaphragm, All-Position

Starter............................................................................................................................................................................................................... Auto Rewind

Muffler..................................................................................................................................................................................................... Baffled with Guard

Throttle............................................................................................................................................................................................... Manual Spring Return

Fuel Tank Capacity......................................................................................................................................................................................... 14 oz (414 ml)

Drive Shaft Housing .......................................................................................................................................................................... Steel Tube (EZ-Link™)

Throttle Control ........................................................................................................................................................................................ Finger-Tip Trigger

Approximate Unit Weight (No fuel, with handle, cutting attachment and shield)........................................................................ 11.5-13.0 lbs (5.2-5.9 kg)

Cutting Mechanism ........................................................................................................................................................................................ SpeedSpool®

Line Spool............................................................................................................................................................................................. Bump Line Releaser

Line Spool Diameter ............................................................................................................................................................................ 4 inches (101.6 mm)

Trimming Line Diameter ................................................................................................................................................................... .095 inches (2.41 mm)

Cutting Path Diameter, Trimmer Head ................................................................................................................................................. 17 inches (43.2 cm)

NOTES

California / EPA Emission Control Warranty Statement

Your Warranty Rights and Obligations

The California Air Resources Board, the Environmental Protection Agency and Troy-Bilt LLC (Troy-Bilt) are pleased to explain the

emission control system warranty on your 2005 and later small off-road engine. New small off-road engines must be designed, built

and equipped to meet stringent anti-smog standards. Troy-Bilt must warrant the emission control system on your small off-road

engine for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of your small off-road

engine.

Your emission control system may include parts such as the carburetor or fuel-injected system, the ignition system, and catalytic

converter. Also included may be hoses, belts, connectors and other emission-related assemblies.

Where a warrantable condition exists, Troy-Bilt will repair your small off-road engine at no cost to you including diagnosis, parts and

labor.

The 2005 and later small off-road engines are warranted for two years. If any emission-related part on your engine is defective, the

part will be repaired or replaced by Troy-Bilt.

Owners Warranty Responsibilities

• As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in your operator’s

manual. Troy-Bilt recommends that you retain all receipts covering maintenance on your small off-road engine, but Troy-Bilt cannot

deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.

• As the small off-road engine owner, you however should be aware that Troy-Bilt may deny you warranty coverage if your small off-

road engine or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications.

• You are responsible for presenting your small off-road engine to a Troy-Bilt Authorized Service Center as soon as a problem exists.

The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should call 1-800-520-5520.

Manufacturer’s Warranty Coverage

• The warranty period begins on the date the engine or equipment is delivered to the retail purchaser.

• The manufacturer warrants to the initial owner and each subsequent purchaser, that the engine is free from defects in material and

workmanship which cause the failure of a warranted part for a period of two years.

• Repair or replacement of warranted part will be performed at no charge to the owner at an Authorized Troy-Bilt Service Center. For

the nearest location please contact Troy-Bilt at: 1-800-520-5520.

• Any warranted part which is not scheduled for replacement, as required maintenance or which is scheduled for only for regular

inspection to the effect of “Repair or Replace as Necessary” is warranted for the warranty period. Any warranted part which is

scheduled for replacement as required maintenance will be warranted for the period of time up to the first scheduled replacement

point for that part.

• The owner will not be charged for diagnostic labor which leads to the determination that a warranted part is defective, if the

diagnostic work is performed at an Authorized Troy-Bilt Service Center.

• The manufacturer is liable for damages to other engine components caused by the failure of a warranted part still under warranty.

• Failures caused by abuse, neglect or improper maintenance are not covered under warranty.

• The use of add-on or modified parts can be grounds for disallowing a warranty claim. The manufacturer is not liable to cover failures

of warranted parts caused by the use of add-on or modified parts.

• In order to file a claim, go to your nearest Authorized Troy-Bilt Service Center. Warranty services or repairs will be provided at all

Authorized Troy-Bilt Service Centers.

• Any manufacturer approved replacement part may be used in the performance of any warranty maintenance or repair of emission

related parts and will be provided without charge to the owner. Any replacement part that is equivalent in performance or durability

may be used in non-warranty maintenance or repair and will not reduce the warranty obligations of the manufacturer

• The following components are included in the emission related warranty of the engine, air filter, carburetor, primer, fuel lines, fuel

pick up/ fuel filter, ignition module, spark plug and muffler.

MANUFACTURER’S LIMITED WARRANTY FOR:

No implied warranty, including any implied warranty of

merchantability or fitness for a particular purpose,

applies after the applicable period of express written

warranty above as to the parts as identified. No other

express warranty or guaranty, whether written or oral,

except as mentioned above, given by any person or

entity, including a dealer or retailer, with respect to any

product shall bind Troy-Bilt LLC During the period of

the Warranty, the exclusive remedy is repair or

replacement of the product as set forth above. (Some

states do not allow limitations on how long an implied

warranty lasts, so the above limitation may not apply to

you.)

The provisions as set forth in this Warranty provide the

sole and exclusive remedy arising from the sales.

Troy-Bilt LLC shall not be liable for incidental or

consequential loss or damages including, without

limitation, expenses incurred for substitute or

replacement lawn care services, for transportation or

for related expenses, or for rental expenses to

temporarily replace a warranted product. (Some states

do not allow limitations on how long an implied warranty

lasts, so the above limitation may not apply to you.)

In no event shall recovery of any kind be greater than the

amount of the purchase price of the product sold.

Alteration of the safety features of the product shall void

this Warranty. You assume the risk and liability for loss,

damage, or injury to you and your property and/or to

others and their property arising out of the use or misuse

or inability to use the product.

This limited warranty shall not extend to anyone other than

the original purchaser, original lessee or the person for

whom it was purchased as a gift.

How State Law Relates to this Warranty: This warranty

gives you specific legal rights, and you may also have

other rights which vary from state to state.

To locate your nearest service dealer dial

1-800-520-5520.

Troy-Bilt LLC

P.O. Box 361131

Cleveland, OH 44136-0019

The limited warranty set forth below is given by Troy-Bilt

LLC with respect to new merchandise purchased and used

in the United States, its possessions and territories.

Troy-Bilt LLC warrants this product against defects in

material and workmanship for a period of two (2) years

commencing on the date of original purchase and will, at its

option, repair or replace, free of charge, any part found to

be defective in material or workmanship. This limited

warranty shall only apply if this product has been operated

and maintained in accordance with the Operator’s Manual

furnished with the product, and has not been subject to

misuse, abuse, commercial use, neglect, accident,

improper maintenance, alteration, vandalism, theft, fire,

water or damage because of other peril or natural disaster.

Damage resulting from the installation or use of any

accessory or attachment not approved by Troy-Bilt LLC for

use with the product(s) covered by this manual will void

your warranty as to any resulting damage. This warranty is

limited to ninety (90) days from the date of original retail

purchase for any Troy-Bilt product that is used for rental or

commercial purposes, or any other income-producing

purpose.

HOW TO OBTAIN SERVICE: Warranty service is

available, WITH PROOF OF PURCHASE THROUGH

YOUR LOCAL AUTHORIZED SERVICE DEALER. To locate

the dealer in your area, visit our website at www.troybilt.com,

check for a listing in the Yellow Pages, call 1-800-520-

5520 or write to

P.O. Box 361131, Cleveland, OH 44136-

0019

This limited warranty does not provide coverage in

the following cases:

A. Tune-ups - Spark Plugs, Carburetor Adjustments,

Filters

B. Wear items - Bump Knobs, Outer Spools, Cutting Line,

Inner Reels, Starter Pulley, Starter Ropes, Drive Belts

C. Troy-Bilt LLC does not extend any warranty for

products sold or exported outside of the United

States of America, its possessions and territories,

except those sold through Troy-Bilt’s authorized

channels of export distribution.

Troy-Bilt LLC reserves the right to change or improve the

design of any Troy-Bilt Product without assuming any

obligation to modify any product previously manufactured.

Manuel de L’utilisateur

Désherbeuse à gaz à 4-temps

TB575SS &

TB525CS

CONSERVEZ CES INSTRUCTIONS

Obtenez la liste des concessionnaires agréés appelez le 1-800-

520-5520. Pour de plus amples informations à propos de votre

appareil, visitez www.troybilt.com.

NE RETOURNEZ PAS L'APPAREIL AU DÉTAILLANT CHEZ QUI

VOUS L'AVEZ ACHETÉ. TOUT SERVICE SOUS GARANTIE

NÉCESSITE UNE PREUVE D'ACHAT.

CE PRODUIT EST COUVERT PAR UN OU PLUSIEURS

BREVETS AMÉRICAINS, ET D’AUTRES SONT EN INSTANCE.

L’entretien de cette machine pendant et passé la période de

garantie devrait être réalisé exclusivement par un

concessionnaire agréé.

Toutes les informations, illustrations et spécifications

contenues dans ce manuel tiennent compte des dernières

informations techniques disponibles au moment de mettre sous

presse. Nous nous réservons le droit d'y apporter des

modifications à tout moment, sans préavis.

AVERTISSEMENT : Lorsque vous utilisez la

machine, vous devez suivre les consignes de

sécurité. Veuillez lire ces instructions avant d’opérer

la machine pour vous assurer de la sécurité de

l’opérateur et de tout spectateur. Veuillez conserver

ces instructions pour un usage ultérieur.

PARE-ÉTINCELLES

REMARQUE : à l'intention des utilisateurs opérant dans les

terres forestières des États-Unis et dans les états de

Californie, du Maine, de l'Orégon et de Washington. Toutes

les terres forestières des États-Unis et de l'état de Californie

(Codes sur les ressources publiques 4442 et 4443), de l'Orégon

et de Washington exigent de par la loi que certains moteurs à

combustion interne utilisés dans des zones couvertes de taillis

ou d'herbe soient équipés d'un pare-étincelles en parfait état de

fonctionnement, ou qu'ils soient conçus, équipés et entretenus

pour la prévention des incendies. Renseignez-vous auprès des

autorités de votre province ou de votre municipalité concernant

la réglementation en vigueur. Vous pourriez être passible d'une

amende ou être tenu responsable si vous ne respectez pas cette

réglementation. Cet appareil est équipé d'un pare-étincelles en

usine. Si l'écran pare-étincelles, réf. 753-05297, doit être

remplacé, communiquez avec le service technique.

AVERTISSEMENT DE LA PROPOSITION 65 DE CALIFORNIE

P/N 769-01920 (11/05)

TABLE DES MATIÈRES

Service technique . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F1

Consignes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . .F2

Informations sur l'huile et le carburant . . . . . . . . . . . . . .F3

Instructions de montage . . . . . . . . . . . . . . . . . . . . . . . . .F4

Familiarisez-vous avec votre appareil . . . . . . . . . . . . . . .F4

Instructions de démarrage et d'arrêt . . . . . . . . . . . . . . . .F5

Mode d'emploi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F6

Entretien et réparations . . . . . . . . . . . . . . . . . . . . . . . . . .F7

Nettoyage et entreposage . . . . . . . . . . . . . . . . . . . . . . .F12

Tableau de dépannage . . . . . . . . . . . . . . . . . . . . . . . . .F13

Caractéristiques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F14

Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F15

Liste des pièces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E18

AVERTISSEMENT

LES GAZ D'ÉCHAPPEMENT DU MOTEUR DE CET APPAREIL

CONTIENNENT DES PRODUITS CHIMIQUES CONSIDÉRÉS PAR

L'ÉTAT DE CALIFORNIE COMME POUVANT CAUSER LE

CANCER, DES MALFORMATIONS CONGÉNITALES OU D'AUTRES

EFFETS NOCIFS SUR L'APPAREIL DE REPRODUCTION.

• IMPORTANTES CONSIGNES DE SÉCURITÉ •

LIRE TOUTES LES INSTRUCTIONS AVANT UTILISATION

• Veuillez lire les instructions avec soin. Familiarisez-vous avec les

commandes et l'utilisation correcte de cet appareil.

• N'utilisez pas l'appareil si vous êtes fatigué, malade ou sous l'effet

de l'alcool, de drogues ou de médicaments.

• Les enfants et adolescents de moins de 15 ans ne doivent pas

utiliser l'appareil exceptés les adolescents assistés d'un adulte.

• Inspectez l'appareil avant utilisation. Remplacez les pièces

endommagées. Regardez s'il y a des fuites de carburant. Assurez-

vous que les fixations sont solidement en place. Remplacez les

pièces de l'accessoire de coupe qui sont fendillées, ébréchées ou

endommagées. Assurez-vous que l'accessoire de coupe est

correctement installé et solidement fixé. Assurez-vous que le

protecteur d'accessoire de coupe est correctement fixé et

positionné comme recommandé. Vous risquez sinon de causer des

blessures à l'opérateur et aux spectateurs, et d'endommager

l'appareil.

• N'utilisez que du fil de remplacement d’origine du fabricant de 2,03

mm, 0,080 po de diamètre. N'utilisez jamais de fil, de chaîne ou de

cordon à renfort métallique car ils peuvent se briser et se

transformer en projectile dangereux.

• Soyez conscient des risques de blessure à la tête, aux mains et aux

pieds.

• Dégagez la zone de coupe avant chaque usage. Enlevez tous les

objets pouvant être projetés ou happés par l'accessoire de coupe :

cailloux, verre brisé, clous, fil ou ficelle. Éloignez enfants,

spectateurs et animaux de la zone de coupe. Tenez-les à au moins

15 m (50 pi) de là mais sachez que les spectateurs risquent quand

même d'être atteints par des objets projetés. Les spectateurs

doivent porter des protections oculaires. Arrêtez immédiatement le

moteur et l'accessoire de coupe si quelqu'un s'approche de vous.

• Appuyez sur la manette des gaz et assurez-vous qu'elle revient

automatiquement en position de ralenti. Procédez à tous les

réglages ou réparations avant d'utiliser l'appareil.

AVERTISSEMENTS DE SÉCURITÉ CONCERNANT LES

DÉSHERBEUSES À GAZ

• Ne stockez le carburant que dans des contenants spécialement

conçus et homologués pour le stockage de ce type de matières.

• Arrêtez toujours le moteur et laissez-le refroidir avant de remplir le

réservoir de carburant. N'enlevez jamais le bouchon du réservoir et

n'ajoutez jamais de carburant pendant que le moteur est chaud. Ne

faites jamais fonctionner l'appareil sans que le bouchon de

carburant soit bien mis. Desserrez lentement le bouchon afin de

réduire la pression du réservoir.

• Évitez de créer une source d'allumage pour le carburant déversé. Ne

démarrez pas le moteur avant que les vapeurs de carburant ne se

soient dissipées.

• Ajoutez le carburant dans un endroit bien aéré et propre en plein air

à l'abri des étincelles ou des flammes. N'enlevez lentement le

bouchon du réservoir d'essence qu'après avoir arrêté le moteur. Ne

fumez pas pendant le remplissage de carburant. Essuyez

immédiatement tout déversement de carburant de l'appareil.

• Éloignez l'appareil d'au moins 9.1 m (30 pi) de la source de

ravitaillement en carburant avant de démarrer le moteur. Ne fumez

pas et éloignez toute source d'étincelles ou de flammes vives du lieu

de ravitaillement ou de fonctionnement de l'appareil.

PENDANT L'UTILISATION DE L'APPAREIL

• Évitez de démarrer ou de faire marcher l'appareil à l'intérieur d'une

pièce ou d'un bâtiment fermé. La respiration de fumées

d'échappement peut tuer. Ne faites fonctionner cet appareil qu'à

l'extérieur dans un endroit bien aéré.

• Portez des lunettes de sécurité conformes aux normes ANSI Z87.1

ainsi que des protège-oreilles durant l'utilisation de l'appareil. Portez

un masque facial ou antipoussières si vous travaillez dans un lieu

poussiéreux.

• Portez des pantalons épais et longs, des bottes, des gants et une

chemise à manches longues. Ne marchez pas pieds nus et évitez

les vêtements lâches, bijoux, pantalons courts et sandales. Relevez

les cheveux au-dessus des épaules.

• Le protecteur d'accessoire de coupe doit toujours être en place lors

de l'utilisation de l'appareil. Ne faites pas marcher l'appareil sans

que les deux fils soient bien déployés, en supposant qu'un fil

approprié a été installé. Assurez-vous que le fil ne dépasse pas le

protecteur de sécurité.

• Cet appareil est muni d'un embrayage. L'accessoire de coupe reste

stationnaire lorsque le moteur est au ralenti. Si ce n'est pas le cas,

faites régler l'appareil par un technicien agréé.

• Ajustez la poignée selon votre taille pour mieux l'agripper.

• N'utilisez l'appareil qu'en plein jour ou avec un bon éclairage

artificiel.

• Évitez tout démarrage accidentel. Mettez-vous en position de

démarrage chaque fois que vous tirez sur la corde de démarrage.

L'opérateur et l'appareil doivent tous deux être en position stable à

ce moment-là. Voir les Instructions de démarrage et d'arrêt.

• Ne vous étirez pas. Tenez-vous toujours bien sur vos pieds en

position d'équilibre.

• Tenez toujours l'appareil des deux mains lorsque vous le faites

marcher. Agrippez fermement les poignées avant et arrière.

• Gardez les mains, le visage et les pieds éloignés des pièces

mobiles. Ne touchez pas et n'essayez pas d'arrêter l'accessoire de

coupe en rotation.

• Ne touchez pas le moteur, le boîtier d'engrenages ni le silencieux.

Ces pièces deviennent très chaudes à l'utilisation. Elles restent

chaudes brièvement après l'arrêt.

• Servez-vous des outils appropriés. N'utilisez cet outil que pour son

usage prévu.

• Ne faites pas fonctionner le moteur à un régime plus élevé que

nécessaire pour couper, tailler ou faire les bordures. Ne faites pas

tourner le moteur à haut régime si vous ne vous faites pas de coupe.

• Arrêtez toujours le moteur lorsque vous suspendez la coupe ou

lorsque vous vous déplacez d'un lieu de travail vers un autre.

• Si vous heurtez un corps étranger ou que celui-ci est happé, arrêtez

le moteur immédiatement et vérifiez que rien n'a été endommagé.

Ne faites pas fonctionner avant réparation des dommages. Ne faites

pas marcher l'appareil si les pièces sont desserrées ou

endommagées.

• Arrêtez et éteignez le moteur dans les cas suivants:

entretien, réparation ou changement d'accessoires ou autres.

• N'utilisez que des pièces de équipement original rechange et

accessoires d’origine du fabricant pour cet appareil. Elles sont

disponibles auprès de votre concessionnaire agréé. L'utilisation de

pièces ou accessoires autres que ceux de éqiupement original peut

causer des blessures graves, endommager l’appareil et annuler sa

garantie.

• Gardez l'appareil exempt d'accumulation de végétation ou autres

matières. Celles-ci peuvent rester logées entre l'accessoire de

coupe et le protecteur.

• Afin de diminuer les risques d'incendie, remplacez tout

silencieux ou pare-étincelles défectueux et conservez le moteur et le

silencieux exempts d'herbe, de feuilles et d'accumulation excessive

de graisse ou de carbone.

AUTRES AVERTISSEMENTS DE SÉCURITÉ

• N'entreposez jamais l'appareil rempli de carburant dans un édifice

où les vapeurs peuvent atteindre une source de flammes vives ou

d'étincelles.

• Laissez le moteur se refroidir avant de l'entreposer ou de le

transporter. Attachez bien l'appareil pendant le transport.

• Rangez l'appareil dans un endroit verrouillé et sec, ou élevé et sec,

hors de portée des enfants, pour éviter une utilisation indésirable ou

un accident.

• Ne trempez et n'arrosez jamais l'appareil avec de l'eau ou tout autre

liquide. Gardez les poignées sèches, propres et exemptes de débris.

Nettoyez après chaque usage. Voir les sections Nettoyage et

Entreposage.

• Conservez ces instructions. Consultez-les souvent et

servez-vous en pour instruire d'autres usagers. Si vous prêtez

l'appareil à quelqu'un, prêtez-lui également ces instructions.

CONSERVER CES INSTRUCTIONS

CONSIGNES DE SÉCURITÉ

AVERTISSEMENT: l'essence est extrêmement

inflammable et ses vapeurs peuvent exploser si on y

met le feu. Veuillez prendre les précautions suivantes.

La page charge ...

MTD TB525CS Le manuel du propriétaire

Marque: MTD

Modèle: TB525CS

Catégorie: Coupe-herbe

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: MTD TB525CS Owner's manual
español: MTD TB525CS El manual del propietario

Autres documents

Ryobi Trimmer 825r Manuel utilisateur