Ryobi Trimmer 825r Manuel utilisateur

825r

4-Cycle Gas Trimmer

OPERATOR’S MANUAL

FOR QUESTIONS, CALL 1-800-345-8746 in U.S. or

1-800-668-1238 in CANADA

www.RyobiOutdoor.com

IMPORTANT MANUAL DO NOT THROW AWAY

2

THANK YOU

Thank you for buying this quality product. This modern

outdoor power tool will provide many hours of useful

service. You will find it to be a great labor-saving device.

This operator’s manual provides you with easy-to-

understand operating instructions. Read the whole

manual and follow all the instructions to keep your new

outdoor power tool in top operating condition.

PRODUCT REFERENCES, ILLUSTRATIONS AND

SPECIFICATIONS

All information, illustrations and specifications in this

manual are based on the latest product information

available at the time of printing. We reserve the right to

make changes at any time without notice.

Copyright

©

2003 MTD SOUTHWEST INC

SpeedSpool

®

is a registered trademark of MTD

SOUTHWEST INC.

SERVICE INFORMATION

Service on this unit both within and after the warranty

period should be performed only by an authorized and

approved service dealer.

• Call 1-800-345-8746 in the United States, or

1-800-668-1238 in Canada, to obtain a list of

authorized service dealers near you

Or

• Go to www.RyobiOutdoor.com on the World Wide

Web for a list of authorized service dealers

DO NOT RETURN THE UNIT TO THE RETAILER.

NOTE: PROOF OF PURCHASE WILL BE REQUIRED

FOR WARRANTY SERVICE.

Make sure you carefully read and understood this

manual before starting or operating this equipment.

THIS PRODUCT IS COVERED BY ONE OR MORE US

PATENTS, OTHER PATENTS PENDING.

INTRODUCTION TABLE OF CONTENTS

I. California Proposition 65 Warning . . . . . . . . . . . . . . . . 3

II. Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . . 3-7

A. Important Safety Information . . . . . . . . . . . . . . . . . 4

B. Safety and International Symbols . . . . . . . . . . . . . 6

C. Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

III. Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . 8

A. Installing and Adjusting the J handle . . . . . . . . . . 8

B. Installing the Cutting Attachment Shield . . . . . . . . 8

IV. Oil and Fuel Information . . . . . . . . . . . . . . . . . . . . 9-10

A. Recommended Oil Type . . . . . . . . . . . . . . . . . . . . .9

B. Adding Oil to the Crankcase . . . . . . . . . . . . . . . . . .9

C. Recommended Fuel Type . . . . . . . . . . . . . . . . . . .10

D. Fueling the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . .10

V. Starting/Stopping Instructions . . . . . . . . . . . . . . . . . 11

VI. Operating Instructions . . . . . . . . . . . . . . . . . . . . 12-13

A. Operating the EZ-Link System . . . . . . . . . . . . . . .12

B. Holding the Trimmer . . . . . . . . . . . . . . . . . . . . . . 13

C. Adjusting Trimming Line Length . . . . . . . . . . . . . 13

D. Tips for Best Trimming Results . . . . . . . . . . . . . . 13

E. Decorative Trimming . . . . . . . . . . . . . . . . . . . . . . 13

VII. Maintenance and Repair Instructions . . . . . . . . . 14-22

A. Maintenance Schedule . . . . . . . . . . . . . . . . . . . . 14

B. Line Installation for the SpeedSpool . . . . . . . . . . 14

C. Installing a Prewound Reel . . . . . . . . . . . . . . . . . 15

D. Cleaning the SpeedSpool . . . . . . . . . . . . . . . . . . 16

E. SpeedSpool Replacement Parts . . . . . . . . . . . . . 16

F. Checking the Oil Level . . . . . . . . . . . . . . . . . . . . . .17

G. Changing the Oil Level . . . . . . . . . . . . . . . . . . . . . .17

H. Air Filter Maintenance . . . . . . . . . . . . . . . . . . . . . 18

I. Carburetor Adjustment . . . . . . . . . . . . . . . . . . . . 18

J. Rocker Arm Clearance . . . . . . . . . . . . . . . . . . . . . .19

K. Replacing the Spark Plug . . . . . . . . . . . . . . . . . . 21

L. Spark Arrestor Maintenance . . . . . . . . . . . . . . . . .21

M.Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

N. Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

O. Long Term Storage . . . . . . . . . . . . . . . . . . . . . . . 22

P. Transporting the Unit . . . . . . . . . . . . . . . . . . . . . . .22

Q. Accessories/Replacement parts . . . . . . . . . . . . . .22

VIII.Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . 23

IX. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

X. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

XI. Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

CONTENTS OF CARTON

•Model 825r Trimmer with J-Handle

• SpeedSpool

®

Bump Head Cutting Attachment

•Operator's Manual

• Product Registration Card

• Bottle of 4-Cycle Oil

3

NOTE: For users on U.S. Forest Land and in the states of California, Maine, Oregon and Washington. All U.S.

Forest Land and the state of California (Public Resources Codes 4442 and 4443), Oregon and Washington require, by

law that certain internal combustion engines operated on forest brush and/or grass-covered areas be equipped with a

spark arrestor, maintained in effective working order, or the engine be constructed, equipped and maintained for the

prevention of fire. Check with your state or local authorities for regulations pertaining to these requirements. Failure to

follow these requirements could subject you to liability or a fine. This unit is factory equipped with a spark arrestor. If

it requires replacement, ask your local service dealer to install the Accessory Part #180890 Spark Arrestor Kit.

Read the Operator’s Manual(s) and follow all warnings and safety instructions. Failure to do so can

result in serious injury to the operator and/or bystanders.

FOR QUESTIONS, CALL 1-800-345-8746 IN U.S. OR 1-800-668-1238 in CANADA

SPARK ARRESTOR

WARNING!

RULES FOR SAFE OPERATION

CALIFORNIA PROPOSITION 65 WARNING

WARNING

THE ENGINE EXHAUST FROM THIS

PRODUCT CONTAINS CHEMICALS

KNOWN TO THE STATE OF CALIFORNIA

TO CAUSE CANCER, BIRTH DEFECTS

OR OTHER REPRODUCTIVE HARM.

DANGER

:

Failure to obey a safety warning

will result in serious injury to yourself or to

others. Always follow the safety

precautions to reduce the risk of fire,

electric shock and personal injury.

WARNING: Failure to obey a safety

warning can result in injury to yourself and

others. Always follow the safety

precautions to reduce the risk of fire,

electric shock and personal injury.

CAUTION: Failure to obey a safety warning

may result in property damage or personal

injury to yourself or to others. Always follow

the safety precautions to reduce the risk of

fire, electric shock and personal injury.

SAFETY ALERT SYMBOL: Indicates

danger, warning or caution. Attention is

required in order to avoid serious personal

injury. May be used in conjunction with

other symbols or pictographs.

SYMBOL MEANING

The purpose of safety symbols is to attract your

attention to possible dangers. The safety symbols,

and their explanations, deserve your careful attention

and understanding. The safety warnings do not by

themselves eliminate any danger. The instructions or

warnings they give are not substitutes for proper

accident prevention measures.

NOTE: Advises you of information or instructions vital

to the operation or maintenance of the

equipment.

SYMBOL MEANING

4

WHILE OPERATING

• Never start or run the unit inside a closed room or

building. Breathing exhaust fumes can kill. Operate

this unit only in a well ventilated outdoor area.

• Wear safety glasses or goggles that are marked as

meeting ANSI Z87.1-1989 standards. Also wear

ear/hearing protection when operating this unit. Wear

a face or dust mask if the operation is dusty. Long

sleeve shirts are recommended.

• Wear heavy, long pants, boots and gloves. Do not

wear loose clothing, jewelry, short pants, sandals or

go barefoot. Secure hair above shoulder level.

• The cutting attachment shield must always be in place

while operating the unit. Do not operate unit without

both trimming lines extended, and the proper line

installed. Do not extend the trimming line beyond the

length of the shield.

• This unit has a clutch. The cutting attachment remains

stationary when the engine is idling. If it does not, have

the unit adjusted by an authorized service technician.

• Adjust the J-handle to your size to provide the best

grip.

• Be sure the cutting attachment is not in contact with

anything before starting the unit.

• Use the unit only in daylight or good artificial light.

• Avoid accidental starting. Be in the starting position

whenever pulling the starter rope. The operator and

unit must be in a stable position while starting. See

Starting/Stopping Instructions.

• Use the right tool. Only use this tool for the purpose

intended.

• Do not overreach. Always keep proper footing and

balance.

• Always hold the unit with both hands when operating.

Keep a firm grip on both the front and rear handle or

grips.

• Keep hands, face, and feet at a distance from all

moving parts. Do not touch or try to stop the cutting

attachment when it is rotating.

• Do not touch the engine or muffler. These parts get

extremely hot from operation. They remain hot for a

short time after you turn off the unit.

RULES FOR SAFE OPERATION

READ ALL INSTRUCTIONS

BEFORE OPERATING

• Read the instructions carefully. Be familiar with the

controls and proper use of the unit.

• Do not operate this unit when tired, ill or under the

influence of alcohol, drugs or medication.

• Children and teens under the age of 15 must not use

the unit, except for teens guided by an adult.

• Inspect the unit before use. Replace damaged parts.

Check for fuel leaks. Make sure all fasteners are in

place and secure. Replace cutting attachment parts

that are cracked, chipped or damaged in any way.

Make sure the cutting attachment is properly installed

and securely fastened. Be sure the cutting attachment

shield is properly attached, and positioned as

recommended. Failure to do so can result in personal

injury to the operator and bystanders, as well as

damage to the unit.

• Use only 0.080 inch (

2.03 mm) diameter Genuine

Factory Parts™ replacement line. Never use metal-

reinforced line, wire or rope. These can break off and

become dangerous projectiles.

• Be aware of the risk of injury to the head, hands and

feet.

• Clear the area to be cut before each use. Remove all

objects such as rocks, broken glass, nails, wire or

string. They can be thrown or become entangled in the

cutting attachment. Clear the area of children,

bystanders, and pets. At a minimum, keep all children,

bystanders and pets outside a 50-foot (15 m.) radius;

there still may be a risk to bystanders from thrown

objects. Bystanders should be encouraged to wear

eye protection. If you are approached, stop the engine

and cutting attachment immediately.

• Squeeze the throttle control and check that it returns

automatically to the idle position. Make all adjustments

or repairs before using unit.

• This unit was not designed to be used as a

brushcutter. Do not attach or operate this unit with any

type of brushcutting blade or brushcutting attachment.

SAFETY WARNINGS FOR GAS TRIMMERS

• Store fuel only in containers specifically designed and

approved for the storage of such materials.

• Always stop the engine and allow it to cool before

filling the fuel tank. Never remove the cap of the fuel

tank, or add fuel, when the engine is hot. Never

operate the unit without the fuel cap securely in place.

Loosen the fuel tank cap slowly to relieve any pressure

in the tank.

• Add fuel in a clean, well-ventilated outdoor area where

there are no sparks or flames. Slowly remove the fuel

cap only after stopping engine. Do not smoke while

fueling. Wipe up any spilled fuel from the unit

immediately.

• Avoid creating a source of ignition for spilled fuel. Do

not start the engine until fuel vapors dissipate.

• Move the unit at least 30 feet (9.1 m) from the fueling

source and site before starting the engine. Do not

smoke. Keep sparks and open flames away from the

area while adding fuel or operating the unit.

5

• Do not operate the engine faster than the speed

needed to cut, trim or edge. Do not run the engine at

high speed when you are not cutting.

• Always stop the engine when cutting is delayed or

when walking from one cutting location to another.

• If you strike or become entangled with a foreign

object, stop the engine immediately and check for

damage. Do not operate before repairing damage. Do

not operate the unit with loose or damaged parts.

• Stop and switch the engine to off for maintenance,

repair, or for changing the cutting attachment or other

attachments.

• Use only Genuine Factory Parts™ replacement parts

and accessories for this unit. These are available from

your authorized service dealer. Use of any

unauthorized parts or accessories could lead to

serious injury to the user, or damage to the unit, and

void your warranty.

• Keep unit clean of vegetation and other materials.

They may become lodged between the cutting

attachment and shield.

•To reduce fire hazard, replace faulty muffler and spark

arrestor, keep the engine and muffler free from grass,

leaves, excessive grease or carbon build up.

RULES FOR SAFE OPERATION

OTHER SAFETY WARNINGS

• Never store the unit, with fuel in the tank, inside a

building where fumes may reach an open flame or spark.

• Allow the engine to cool before storing or transporting.

Be sure to secure the unit while transporting.

• Store the unit in a dry area, locked up or up high

to prevent unauthorized use or damage, out of the

reach of children.

• Never douse or squirt the unit with water or any other

liquid. Keep handles dry, clean and free from debris.

Clean after each use. See the Cleaning and Storage

instructions.

• Keep these instructions. Refer to them often and use

them to instruct other users. If you loan someone this

unit, also loan them these instructions.

SAVE THESE INSTRUCTIONS

6

SYMBOL MEANING

• SAFETY ALERT SYMBOL

Indicates danger, warning, or

caution. May be used in conjunction

with other symbols or pictographs.

• WARNING - READ OPERATOR'S

MANUAL

Read the Operator’s Manual(s) and

follow all warnings and safety

instructions. Failure to do so can

result in serious injury to the

operator and/or bystanders.

• WEAR EYE AND HEARING

PROTECTION

WARNING

:

Thrown objects and

loud noise can cause severe eye

injury and hearing loss. Wear eye

protection meeting ANSI Z87.1-1989

standards and ear protection when

operating this unit.

Use a full face

shield when needed.

• KEEP BYSTANDERS AWAY

WARNING

:

Keep all bystanders,

especially children and pets, at least

50 feet (15 m.) from the operating area.

• UNLEADED FUEL

Always use clean, fresh unleaded fuel.

• OIL

Refer to operator's manual for the

proper type of oil.

SAFETY AND INTERNATIONAL SYMBOLS

This operator's manual describes safety and international symbols and pictographs that may appear on this product.

Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.

SYMBOL MEANING

• THROWN OBJECTS AND

ROTATING CUTTER CAN CAUSE

SEVERE INJURY

WARNING

:

Do not operate without

the cutting attachment shield in

place. Keep away from the rotating

cutting attachment.

•ON/OFF STOP CONTROL

ON / START / RUN

•ON/OFF STOP CONTROL

OFF OR STOP

• HOT SURFACE WARNING

Do not touch a hot muffler or

cylinder. You may get burned. These

parts get extremely hot from

operation. When turned off they

remain hot for a short time.

• SHARP BLADE

WARNING: Sharp blade on cutting

attachment shield. To prevent

serious injury, do not

touch line cutting blade.

RULES FOR SAFE OPERATION

7

RULES FOR SAFE OPERATION

APPLICATIONS

As a trimmer:

• Cutting grass and light weeds

• Edging

• Decorative trimming around trees, fences, etc.

Other optional accessories may be used with the

825r. Refer to Operating the EZ-Link System for a

list of add-ons.

KNOW YOUR UNIT

Cutting Attachment

Shield

Fuel Cap

Throttle

Control

J-Handle

Cutting Attachment

Shaft Grip

Primer Bulb

Choke Lever

Oil Fill Plug / Dipstick

Air Filter Cover

Engine Feet

Spark Plug

On/Off Stop Control

Shaft Housing

Starter Rope Grip

Line Cutting Blade

Spark Plug

Muffler

Muffler Guard

Spark Arrestor

EZ-Link™

8

ASSEMBLY INSTRUCTIONS

INSTALL AND ADJUST THE J-HANDLE

The J-handle comes installed on this unit. Use the

following information if you ever need to reinstall it.

1. Place the J-handle between the top and middle

clamp pieces (Fig. 1).

2. While holding the three pieces together, install the four

(4) screws through the top clamp and into middle clamp.

NOTE: The holes in the top and middle clamp will line up

only when assembled correctly.

3. Place the clamps and the J-handle over the shaft

housing and onto the bottom clamp.

4. Hold each hex nut in the bottom clamp recess with a

finger. Start screws with a large Phillips screwdriver.

Do not tighten until you make the handle adjustment.

5. Slide the J-handle in or out until the arrow/white line on

the decal touches the clamp assembly (Fig. 2). You must

first loosen the screws if the handle is pre-installed.

Fig. 1

Fig. 3

6. While holding the unit in the operating position (Fig. 3),

position the J-handle to the location that provides you

the best grip.

7. Tighten the clamp screws evenly, until the J-handle

is secure.

(4) Screws

Top Clamp

J-Handle

Middle Clamp

Bottom Clamp

Nuts

Decal

Fig. 2

INSTALL THE CUTTING ATTACHMENT SHIELD

Use the following instructions if the cutting attachment

shield on your unit is not installed.

1. Place the cutting attachment shield onto the shaft

housing above the clamp assembly (Fig. 4).

2. Push the cutting attachment shield down to the top of

the cutting attachment assembly and then rotate the

cutting attachment shield until the screw holes align

and the guard fits into the recessed pocket (Fig. 5).

3. Install the screws with a Phillips screwdriver (Fig. 6).

WARNING: To prevent serious personal

injury, never operate the trimmer without

the cutting attachment shield in place.

Fig. 4

Fig. 5

Shaft Housing

Fig. 6

(4) Screws

Clamp

Assembly

Cutting

Attachment

Assembly

Cutting Attachment

Shield

Recessed

Pocket

9

DANGER: OVERFILLING OIL CRANKCASE

MAY CAUSE SERIOUS PERSONAL

INJURY. Check and maintain the proper oil

level in the crank case; it is important and

cannot be overemphasized. Check the oil

before each use and change it as needed.

See Changing the Oil.

RECOMMENDED OIL TYPE

Using the proper type and weight of oil in the crankcase

is extremely important. Check the oil before each use

and change the oil regularly. Failure to use the correct

oil, or using dirty oil, can cause premature engine wear

and failure.

Use a high-quality SAE 30 weight oil of API (American

Petroleum Institute) service class SF, SG, SH.

ADDING OIL TO CRANKCASE: INITIAL USE

NOTE: This unit is shipped without oil. In order to avoid

damage to the unit, put oil in the crankcase

before you attempt to start the unit.

Your unit is supplied with one 3.4 fluid oz. (100 ml.)

bottle of SAE 30 SF, SG, SH oil (Fig. 7).

NOTE: Save the bottle of oil. It can be used to measure

the correct amount during future oil changes.

See Changing the Oil.

1. Unscrew the top of the bottle of oil and remove the

paper seal covering the opening. Replace the top.

Next, cut the tip off the funnel spout (Fig. 7).

2. Place the unit on a flat level surface.

3. Remove the oil plug / dipstick from the crankcase

(Fig. 8).

Fig. 7

Fig. 9

Oil Fill

NOTE: Never add oil to the fuel or fuel tank.

5. Wipe up any oil that may have spilled and reinstall

the oil fill plug / dipstick.

Check oil before each use and change as needed. Refer

to Changing the Oil.

Oil Fill Plug/Dipstick

Oil Fill Hole

Fig. 8

4. Pour the entire bottle of oil into the oil fill hole

(Fig. 9).

O-Ring

Funnel Spout

OIL AND FUEL INFORMATION

10

FUELING THE UNIT

1. Remove the fuel cap (Fig. 10).

Fig. 10

Fuel Cap

Fuel Tank

Gas Can Spout

2. Place the gas container’s spout into the fill hole on

the fuel tank (Fig. 10) and fill the tank.

NOTE: Do not overfill the tank.

3. Wipe up any gasoline that may have spilled.

4. Reinstall the fuel cap.

5. Move the unit at least 30 ft. (9.1 m) from the fueling

source and site before starting the engine.

NOTE: Dispose of the old gasoline in accordance to

Federal, State and Local regulations.

RECOMMENDED FUEL TYPE

Old fuel is the primary reason for improper unit

performance. Be sure to use fresh, clean, unleaded

gasoline.

NOTE: This is a four cycle engine. In order to avoid

damage to the unit, do not mix oil with

gasoline.

Definition of Blended Fuels

Today's fuels are often a blend of gasoline and

oxygenates such as ethanol, methanol or MTBE (ether).

Alcohol-blended fuel absorbs water. As little as 1%

water in the fuel can make fuel and oil separate or form

acids when stored. Use fresh fuel (less than 60 days

old), when using alcohol-blended fuel.

Using Blended Fuels

If you choose to use a blended fuel, or its use is

unavoidable, follow recommended precautions:

• Always use fresh unleaded gasoline

• Use the fuel additive STA-BIL

®

or an equivalent

• Drain tank and run the engine dry before storing unit

Using Fuel Additives

The use of fuel additives, such as STA-BIL

®

Gas

Stabilizer or an equivalent, will inhibit corrosion and

minimize the formation of gum deposits. Using a fuel

additive can keep fuel from forming harmful deposits in

the carburetor for up to six (6) months. Add 0.8 oz.

(23 ml.) of fuel additive per gallon of fuel according to the

instructions on the container. NEVER add fuel additives

directly to the unit's gas tank.

Unleaded

Gasoline

WARNING: Add gasoline in a clean, well-

ventilated outdoor area. Avoid creating a

source of ignition for spilt fuel.

WARNING: Never operate the unit without

the fuel cap securely in place.

WARNING: Gasoline is extremely flammable

and its vapors can explode if ignited. To avoid

serious personal injury, always stop the engine

and allow it to cool before filling the fuel tank.

Do not smoke while filling the tank. Keep

sparks and open flames away from the area.

WARNING: Remove the fuel cap slowly to

avoid injury from gasoline spray.

OIL AND FUEL INFORMATION

11

STARTING/STOPPING INSTRUCTIONS

Fig. 13

1. Check the oil level in the crankcase. Refer to

Checking the Oil Level.

2. Fill the fuel tank with fresh, clean unleaded gasoline.

Refer to Fueling the Unit.

3. Put the Start/Stop Engine Control in the START [

I

]

position (Fig. 11).

4. Place the choke lever in the FULL choke (A)

position (Fig. 12).

NOTE:

Slide the choke lever directly above the appropriate

symbol on filter cover decal

(Fig. 12).

5. Fully press and release the primer bulb slowly 10

times until FUEL IS VISIBLE IN THE PRIMER BULB.

If you can’t see fuel in the bulb, press and release the

bulb as many times as it takes before you can see

fuel in it (Fig. 12).

6. Squeeze the throttle control to the wide open (full

throttle) position.

7. With the unit in the starting position (Fig. 13) and the

choke in the FULL (A) position, pull the starter

rope briskly 5 times. If the engine attempts to run

before the fifth pull, proceed to step 8.

8. Move the choke lever to the PARTIAL (B) position

(Fig. 12).

NOTE: The engine will not run in the FULL choke (A)

position.

9. Pull the starter rope 1 to 3 pulls until the engine

starts. Run for 15-30 seconds. If the unit fails to start,

return to step 7.

10. Move the choke lever to the RUN (C) position and

run at full throttle for 30 seconds.

11. Release the throttle control to the idle position and

begin operation.

NOTE: If the engine does not start using these

procedures, repeat steps 5 through 11 using

TWO (2) pulls in the FULL choke (A) position.

NOTE: Choking is unnecessary when starting a warm

engine. Put the On/Off Stop Control in the ON

position (Fig. 11), and start in PARTIAL choke

(B ) position (Fig. 12). After starting, place the

choke lever in the RUN (C ) position.

WARNING: Operate this unit only in a well-

ventilated area outdoors. Carbon monoxide

exhaust fumes can be lethal in a confined area.

WARNING: Avoid accidental starting. Remain

in the starting position when pulling the

starter rope (Fig. 13). The operator and unit

must be in a stable position while starting to

avoid serious personal injury.

Make sure that any Add-On item is installed

correctly and secure before starting the unit.

STOPPING INSTRUCTIONS

1. Release your hand from the throttle control (Fig. 13).

Allow the engine to cool down by idling.

2. Put the On/Off Stop Control in the OFF (O) position

(Fig. 11).

STARTING INSTRUCTIONS

Start / Stop

Control

Primer Bulb

Choke Lever

Starter Rope

Throttle Control

Fig. 12

Fig. 11

12

For edging when using the line head cutting attachment

with EZ-Link™ models, lock the release button of the

cutting attachment into the 90° edging hole or the 180°

edging hole (Fig. 16).

OPERATING THE EZ-LINK™ SYSTEM

The EZ-Link™ system enables the use of these optional

Add-Ons.

Blower/Vacuum . . . . . . . . . . . . . . . . . . . . . . . . . . BV720r

Cultivator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GC720r

Edger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LE720r

Hedge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . HS720r

Snow Thrower . . . . . . . . . . . . . . . . . . . . . . . . . . . ST720r

Straight Shaft Trimmer . . . . . . . . . . . . . . . . . . . . SS725r

Tree Pruner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TP720r

Turbo Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . TB720r

Removing the Cutting Attachment or Add-Ons

1. Turn the knob counterclockwise to loosen (Fig. 14).

2. Press and hold the release button (Fig. 14).

3. While firmly holding the upper shaft housing, pull

the cutting attachment or add-on straight out of the

EZ-Link™ coupler (Fig. 15).

Installing the Cutting Attachment or Add-Ons

NOTE: To make installing or removing the add-on

easier, place the unit on the ground or on a work

bench.

1. Turn knob counterclockwise to loosen (Fig. 14).

Fig. 14

EZ-Link™ Coupler

Release Button

Guide Recess

Knob

Primary Hole

Upper Shaft Housing

90˚ Edging Hole

EZ-Link™ Coupler

2. While firmly holding the add-on, push it straight into

the EZ-Link™ coupler (Fig. 15).

NOTE: Aligning the release button with the guide recess

will help installation (Fig. 14).

3. Turn the knob clockwise to tighten (Fig. 16).

Fig. 15

Fig. 16

Knob

180˚ Edging Hole

Lower Shaft Housing

Release Button

WARNING: To avoid serious personal injury

and damage to the unit, shut unit off before

removing or installing add-ons.

WARNING: Read and understand the

operator’s manual for each add-on prior to

operation.

CAUTION: The cutting attachment and

add-ons with the EZ-Link™ system are to be

used in the primary hole unless stated

otherwise in the specific add-ons operator’s

manual. Using the wrong hole could lead to

personal injury, or damage to the unit.

CAUTION: Lock the release button in the

primary hole and securely tighten the knob

before operating this unit.

OPERATING INSTRUCTIONS

13

NOTE: Do not rest the Bump Head™ on the ground

while the unit is running.

Some line breakage will occur from:

• Entanglement with foreign matter

• Normal line fatigue

• Attempting to cut thick, stalky weeds

• Forcing the line into objects such as walls or fence

posts

TIPS FOR BEST TRIMMING RESULTS

• Keep the cutting attachment parallel to the ground.

• Do not force the cutting attachment. Allow the tip of

the line to do the cutting, especially along walls.

Cutting with more than the tip will reduce cutting

efficiency and may overload the engine.

• Cut grass over 8 inches (200 mm) by working from

top to bottom in small increments to avoid

premature line wear or engine drag.

• Cut from right to left whenever possible. Cutting to

the left improves the unit's cutting efficiency.

Clippings are thrown away from the operator.

• Slowly move the trimmer into and out of the cutting

area at the desired height. Move either in a forward-

backward or side-to-side motion. Cutting shorter

lengths produces the best results.

• Trim only when grass and weeds are dry.

• The life of your cutting line is dependent upon:

• Following the trimming techniques

• What vegetation is being cut

• Where vegetation is cut

For example, the line will wear faster when trimming

against a foundation wall as opposed to trimming

around a tree.

HOLDING THE TRIMMER

Before operating the unit, stand in the operating position

(Fig. 17). Check for the following:

• The operator is wearing eye protection and proper

clothing

• With a slightly-bent right arm, the operator’s hand is

holding the shaft grip

• The operator’s left arm is straight, the left hand

holding the J-handle

• The unit is at waist level

•

The cutting attachment is parallel to the ground and

easily contacts the grass without the need to bend ove

r

Fig. 17

ADJUSTING TRIMMING LINE LENGTH

The Bump Head™ cutting attachment allows you to

release trimming line without stopping the engine. To

release more line, lightly tap the cutting attachment on the

ground (Fig. 18) while operating the trimmer at high speed.

NOTE: Always keep the trimming line fully extended.

Line release becomes more difficult when the

cutting line gets shorter.

Fig. 18

Each time the head is bumped, about 1 inch (25.4 mm)

of trimming line releases. A blade in the cutting

attachment shield will cut the line to the proper length if

any excess line is released.

For best results, tap the bump knob on bare ground or

hard soil. If you attempt a line release in tall grass, the

engine may stall. Always keep the trimming line fully

extended. Line release becomes more difficult when the

cutting line gets shorter.

DECORATIVE TRIMMING

Decorative trimming is accomplished by removing all

vegetation around trees, posts, fences and more.

Rotate the whole unit so that the cutting attachment is at

a 30° angle to the ground (Fig. 19).

Fig. 19

WARNING: Always wear eye, hearing, foot

and body protection to reduce the risk of

injury when operating this unit.

CAUTION: Do not remove or alter the line

cutting blade assembly. Excessive line length

will make the clutch overheat. This may lead to

serious personal injury or damage to the unit.

OPERATING INSTRUCTIONS

14

LINE INSTALLATION FOR THE SPEEDSPOOL

®

Always use Genuine Factory Parts™ 0.080 inch

(2.03 mm) replacement line. Lines other than those

specified may make the engine overheat or fail.

There are two methods to replace the SpeedSpool

®

trimming line:

• Wind the inner reel with new line

• Install a pre-wound inner reel

Winding the Inner Reel With New Line

NOTE: It Is unnecessary to remove the bump knob to

install a new trimming line.

1. Cut two pieces of 0.080 inch (2.03 mm) trimming

line, 10 feet (3 m) long.

2. Hold the outer spool and turn the inner reel

counterclockwise to line up the arrows on the outer

spool and inner reel (Fig. 20).

Top View Of The SpeedSpool

®

Outer Spool

Inner Reel

Fig. 20

MAINTENANCE SCHEDULE

Perform these required maintenance procedures at the

frequency stated in the table. These procedures should

also be a part of any seasonal tune-up.

NOTE: Some maintenance procedures may require

special tools or skills. If you are unsure about

these procedures take your unit to any non-road

engine repair establishment, individual or

authorized service dealer.

NOTE: Maintenance, replacement, or repair of the

emission control devices and system may be

performed by any non-road engine repair

establishment, individual or authorized service

dealer.

Bump Knob

Arrows

MAINTENANCE AND REPAIR INSTRUCTIONS

WARNING: Never use metal-reinforced line,

wire, chain, or rope, etc. These can break off

and become dangerous projectiles.

WARNING: Always use the correct line

length when installing trimming line on the

unit. The line may not release properly if the

line is too long.

WARNING: To prevent serious injury, never

perform maintenance or repairs with the unit

running. Always service and repair a cool unit.

Disconnect the spark plug wire to ensure that

the unit cannot start.

FREQUENCY MAINTENANCE REQUIRED REFER TO

Before starting engine

Fill fuel tank with fresh fuel

Check oil

Page 10

Page 17

Every 10 hours Clean and re-oil air filter Page 18

First change at 10 hours

Every 25 hours thereafter

Every 25 hours

Change oil

Clean spark arrestor

Page 17

Page 21

10 hours on new engine

Every 25 hours

Check rocker arm to valve clearance and adjust

Check spark plug condition and gap

Page 19

Page 21

15

Line Locking Hole

Trimming Line

Line Loading Hole

Eyelet

5. Insert the line into the locking hole (Fig. 22). Do not

push the line more than a 1/2 inch (12.7 mm) into the

line locking hole. The line will form a small loop

(Fig. 22) when it is inserted correctly.

3. Pull old line out of the line loading and line locking

holes (Fig. 21 and 22).

4. Insert a piece of trimming line straight into one of the

two eyelets in the outer spool. Push it up through the

line loading hole in the inner reel (Fig. 21). Do not

bend the line when inserting it into the eyelet.

Fig. 21

Fig. 22

6. Pull the line from the outer spool until the line is tight

against the inner reel (Fig. 23).

Fig. 23

INSTALLING A PRE-WOUND REEL

1. Turn the bump knob counterclockwise and remove

the bump knob, spring and foam seal (Fig. 26).

9. If winding the line becomes difficult or if the line

jams, pull the ends of the line from the spool

(Fig. 25). Continue winding the inner reel

counterclockwise.

Fig. 24

Fig. 25

7. Repeat procedures 4-6 with the second piece of line.

8. Hold the outer spool. Wind the inner reel

counterclockwise until approximately four (4) inches

(102 mm) of line remain (Fig. 24).

NOTE: Do not wind the inner reel before installing the

second piece of line.

Bump Knob

Foam Seal

Spring

Inner Reel

Fig. 26

MAINTENANCE AND REPAIR INSTRUCTIONS

16

SPEEDSPOOL

®

REPLACEMENT PARTS

Replacement Line . . . . . . . . . . . . . . . . . . . . . . . . 181472

Replacement Line Cartridge . . . . . . . . . . . . . . . . 181460

Inner Reel Spring . . . . . . . . . . . . . . . . . . . . . . . . 181465

Foam Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181467

Inner Reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181464

Bump Head™ Assembly . . . . . . . . . . . . . . . . . . . 181468

(Bump Knob, Inner Reel, Spring)

These SpeedSpool

®

replacement parts can be

purchased from your local authorized dealer.

4. Hold the inner reel in place and install the bump

knob, spring and foam seal. Press down and turn the

bump knob clockwise. Grasp the ends and pull

firmly to release the line from the holding slots in the

inner reel (Fig. 25).

Releasing the Inner Reel

If the SpeedSpool

®

does not release line correctly, pull

the ends of the line firmly from the spool (Fig. 25). If this

does not the release line, follow the Cleaning the

SpeedSpool

®

instructions.

2. Pull the old inner reel with existing line from the outer

spool.

3. Insert the ends of the prewound inner reel line into

the outer spool eyelets (Fig. 27). Push the new inner

reel, arrow side up, into the outer spool.

Fig. 27

4. Remove any existing line from the inner reel before

cleaning. Remove any debris or grass from the knob,

spring, inner reel and foam seal. Wash the inner reel

with warm soapy water (Fig. 29).

Fig. 28

CLEANING THE SPEEDSPOOL

®

Cleaning the SpeedSpool

®

may be necessary if:

•A jammed or excessive line must be removed

• The SpeedSpool

®

becomes difficult to wind or does

not operate correctly when bumping the head on the

ground

1. Hold the outer spool, and unscrew the bump knob

counterclockwise (Fig. 28).

2. Pull out the bump knob, spring and foam seal

(Fig. 26).

Shaft

Plunger

NOTE: The inner reel must be totally dry before

reinstalling it into the outer spool. Do not

lubricate the inner reel or outer spool assembly.

6. Place the inner reel into the outer spool.

7. Place the bump knob, spring and foam seal onto the

inner reel (Fig. 26).

8. Press the bump knob down and tighten clockwise.

9. Install new line as described in Line Installation for

the SpeedSpool

®

.

5. Clean the shaft and the inner surface of the outer

spool. To clean the shaft underneath the plunger,

press down on the plunger (Fig. 30). Remove any dirt

or debris from the shaft.

Fig. 30

Inner Reel

Fig. 29

3. Pull the inner reel with existing line from the outer

spool.

MAINTENANCE AND REPAIR INSTRUCTIONS

17

CHECKING THE OIL LEVEL

The importance of checking and maintaining the proper

oil level in the crankcase cannot be overemphasized.

Check oil before each use:

1. Stop the engine and allow oil to drain into the crankcase.

2. Place the unit on a flat, level surface to get a proper

oil level reading.

3. Keep dirt, grass clippings and other debris out of the

engine. Clean the area around the oil fill plug/dipstick

before removing it.

4. Remove the oil fill plug/dipstick and wipe off oil.

Reinsert it all the way back in.

5. Remove the oil fill plug/dipstick and check the oil level.

Oil should be up to the top of the dipstick (Fig. 31).

6. If the level is low, add a small amount of oil to the oil

fill hole and recheck (Fig. 32). Repeat this procedure

until the oil level reaches the top of the dipstick.

NOTE: Do not overfill the unit.

Top of Dipstick

O-Ring

Oil Fill Plug/Dipstick

CHANGING THE OIL

For a new engine, change the oil after the first 10 hours of

operation. Change the oil while the engine is still warm. The

oil will flow freely and carry away more impurities.

1. Unplug spark plug boot to prevent accidental starting.

2. Remove the oil fill plug/dipstick.

3. Pour the oil out of the oil fill hole and into a container

by tipping the unit to a vertical position (Fig. 33).

Allow ample time for complete drainage.

Fig. 33

Fig. 31

Fig. 32

NOTE: Make sure the O-ring is in place on the oil fill

plug/dipstick when checking and changing the

oil (Fig. 32).

Oil Fill Plug/Dipstick

Oil Fill Hole

O-Ring

Full

Add 1.4-1.5 Oz.

(41-44 ml)

6. Replace the oil fill plug/dipstick.

7. Reconnect the spark plug boot.

4. Wipe up any oil residue on the unit and clean up any

oil that may have spilled. Dispose of the oil

according to Federal, State and local regulations.

5. Refill the crankcase with 3.4 fluid ounce (100 ml) of

SAE 30 SF, SG, SH oil.

NOTE: Use the bottle and spout saved from initial use to

measure the correct amount of oil. The top of the

label on the bottle measures approximately 3.4

ounces (100 ml) (Fig. 34). Check the level with the

dipstick. If the level is low, add a small amount of

oil and recheck. Do not overfill (Fig. 34).

Fill Level

CAUTION: To prevent extensive engine

wear and damage to the unit, always

maintain the proper oil level in the

crankcase. Never operate the unit with the

oil level below the bottom of the dipstick.

CAUTION: Wear gloves to prevent injury

when handling the unit.

Fig. 34

MAINTENANCE AND REPAIR INSTRUCTIONS

18

MAINTENANCE AND REPAIR INSTRUCTIONS

AIR FILTER MAINTENANCE

Cleaning the Air Filter

Clean and re-oil the air filter every 10 hours of operation.

It is an important item to maintain. Failure to maintain the

air filter will VOID the warranty.

1. Open the air filter cover. Push the tab on the right

side of the cover inward. Then pull the air filter cover

out and to the left (Fig. 35).

NOTE: It may be necessary to remove the fuel cap to

completely remove the air filter cover.

2. Remove the air filter (Fig. 35).

3. Wash the filter in detergent and water (Fig. 36). Rinse

the filter thoroughly and allow it to dry.

4. Apply enough clean SAE 30 motor oil to lightly coat

the filter (Fig. 37).

Air Filter

Air Filter Cover

Tab

Fig. 35

Fig. 36

5. Squeeze the filter to spread and remove excess oil

(Fig. 38).

Fig. 39

Back Plate Slot

Slots

6. Replace the filter (Fig. 39).

NOTE: If the unit is operated without the air filter, you

will VOID the warranty.

7. Reinstall the air filter cover. Position the hooks on

the left side of the air filter cover into the slots at the

left side of the back plate (Fig. 39).

NOTE: It may be necessary to remove the fuel cap to

reinstall the air filter cover.

8. Swing the cover to the right until the tab on the air

filter cover snaps into place in the slot on the back

plate (Fig. 39).

9. Replace the fuel cap if it was removed.

Back Plate

WARNING: To avoid serious personal injury,

always turn your trimmer off and allow it to

cool before you clean or service it.

Fig. 37 Fig. 38

CARBURETOR ADJUSTMENT

The idle speed of the engine is adjustable. An idle

adjustment screw is reached though a hole in the top of

the engine cover (Fig. 40).

NOTE: Careless adjustments can seriously damage your

unit. An authorized service dealer should make

carburetor adjustments.

Check Fuel

Old fuel is usually the reason for improper unit

performance. Drain and refill the tank with fresh fuel prior

to making any adjustments. Refer to Oil and Fuel

Information.

19

Idle Adjustment Screw

Clean Air Filter

The condition of the air filter is important to the operation

of the unit. A dirty air filter will restrict air flow. This is

often mistaken for an out of adjustment carburetor.

Check the condition of the air filter before adjusting the

idle speed screw. Refer to Air Filter Maintenance.

Adjust Idle Speed Screw

If, after checking the fuel and cleaning the air filter, the

engine still will not idle, adjust the idle speed screw as

follows:

1. Start the engine and let it run at a high idle for a minute

to warm up. Refer to Starting/Stopping Instructions.

2. Release the throttle trigger and let the engine idle. If the

engine stops, insert a small phillips or flat blade screwdriver

into the hole in the air filter/muffler cover (Fig. 40). Turn

the idle speed screw in, clockwise, 1/8 of a turn at a

time (as needed) until the engine idles smoothly.

NOTE: The cutting attachment should not rotate when

the engine idles.

3. If the cutting attachment rotates when the engine idles,

turn the idle speed screw counterclockwise 1/8 of a

turn at a time (as needed), to reduce idle speed.

Checking the fuel, cleaning the air filter, and adjusting

the idle speed should solve most engine problems. If not

and all of the following are true:

• the engine will not idle

• the engine hesitates or stalls on acceleration

• there is a loss of engine power

Have the carburetor adjusted by an authorized service dealer.

WARNING: The cutting attachment may spin

during idle speed adjustments. Wear

protective clothing and observe all safety

instructions to prevent serious personal injury.

WARNING: To prevent serious personal

injury, make sure the cutting attachment

has stopped rotating before you turn it off

and set it down.

Fig. 40

MAINTENANCE AND REPAIR INSTRUCTIONS

Remove

Screws

Fig. 41

Engine Cover

2. Remove the two (2) screws on top of the engine cover

with a Flat-head or T-25 Torx screwdriver (Fig. 42).

Fig. 42

Engine Cover

Muffler

ROCKER ARM CLEARANCE

This requires disassembly of the engine. If you feel

unsure or unqualified to perform this, take the unit to an

authorized service center.

NOTE: Inspect the valve to rocker arm clearance with a

feeler gauge after the first 10 hours of operation

and then every 25 hours of operation thereafter.

• The engine must be cold when checking or adjusting

the valve clearance.

• This task should be performed inside, in a clean,

dust free area.

1. Remove the muffler cover by pressing down on it,

separating it from the engine cover. Using a flat

blade screwdriver, disengage the middle and front

tabs and slots first. The cover will hinge off from the

rear tab (Fig. 41).

Top View Of The Engine

Front Slot

Front Tab

Middle Tab

Middle Slot

Rear Slot

and Tab

20

MAINTENANCE AND REPAIR INSTRUCTIONS

4. Disconnect the spark plug wire.

5. Clean dirt from around the spark plug. Remove the

spark plug from the cylinder head by turning a 5/8 in.

socket counterclockwise.

6. Remove the engine cover (Fig. 42).

7. Clean dirt from around the rocker arm cover.

Remove the screw holding the rocker arm cover with

a large flat blade screwdriver or Torx T-25 bit

(Fig. 44). Remove the rocker arm cover and gasket.

3. Remove the screw behind the engine cover (Fig. 43).

Rocker Arm Cover

Screw

Fig. 43

Fig. 44

Spark Plug Hole

8. Pull the starter rope slowly to bring the piston to the top

of its travel, (known as top dead center). Check that:

• The piston is at the top of its travel while looking in

the spark plug hole (Fig. 44)

• Both rocker arms move freely, and both valves are

closed

If these statements are not true, repeat this step.

9. Slide the feeler gauge between the rocker arm and

the valve return spring. Measure the clearance

between the valve stem and rocker arm (Fig. 45).

Measure both the intake and exhaust valves.

Adjusting Nuts

Feeler Gauge

Rocker Arms

Fig. 45

Fig. 46

The recommended clearance for both intake and

exhaust is .003 – .006 in. (.076 – 0.152 mm). Use a

standard automotive .005 in. (0.127 mm) feeler gauge.

The feeler gauge should slide between the rocker arm

and valve stem with a slight amount of resistance,

without binding. See Figure 45 and 46.

10. If the clearance is not within specification:

a. Turn the adjusting nut using a 5/16 inch (8 mm)

wrench or nut driver (Fig. 46).

• To increase clearance, turn the adjusting nut

counterclockwise.

• To decrease clearance, turn the adjusting nut

clockwise.

b. Recheck both clearances, and adjust as necessary.

11. Reinstall the rocker arm cover using a new gasket.

Torque the screw to 20–30 in

•lb (2.2–3.4 N•m).

12. Reinstall the engine cover. Check alignment of the

cover before tightening the screws. Tighten screws.

13. Reinstall the muffler cover. Slip the rear tab on the

muffler cover into the engine cover rear slot. Then

slide the remaining slots into the tabs until they snap

into place (Fig. 41).

14. Check the spark plug and reinstall. See Replacing

the Spark Plug.

15. Replace the spark plug wire.

INTAKE

EXHAUST

Feeler Gauge

Adjusting Nut

Rocker Arm

.003–.006 in.

(.076–.152 mm)

Valve Stem

La page charge ...

Ryobi Trimmer 825r Manuel utilisateur

Ce manuel convient également à

Ryobi Trimmer 825r Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents