Yard Machines Y26SS Manuel utilisateur

Marque: Yard Machines

Modèle: Y26SS

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Operator’s Manual

SAVE THESE INSTRUCTIONS

For service call 1-800-800-7310 in the United States, or

1-800-668-1238 in Canada to obtain a list of authorized service

dealers near you. For more details about your unit, visit our

website at www.yardmachines.com.

DO NOT RETURN THE UNIT TO THE RETAILER. PROOF OF

PURCHASE WILL BE REQUIRED FOR WARRANTY

SERVICE.

THIS PRODUCT IS COVERED BY ONE OR MORE U.S.

PATENTS. OTHER PATENTS PENDING.

Service on this unit both within and after the warranty period

should be performed only by an authorized and approved

service dealer.

All information, illustrations, and specifications in this manual

are based on the latest product information available at the

time of printing. We reserve the right to make changes at any

time without notice.

WARNING: When using the unit, you must follow

the safety rules. Please read these instructions

before operating the unit in order to ensure the

safety of the operator and any bystanders. Please

keep these instructions for later use.

SPARK ARRESTOR NOTE

NOTE: For users on U.S. Forest Land and in the states of

California, Maine, Oregon and Washington. All U.S. Forest

Land and the state of California (Public Resources Codes 4442

and 4443), Oregon and Washington require, by law that certain

internal combustion engines operated on forest brush and/or

grass-covered areas be equipped with a spark arrestor,

maintained in effective working order, or the engine be

constructed, equipped and maintained for the prevention of

fire. Check with your state or local authorities for regulations

pertaining to these requirements. Failure to follow these

requirements could subject you to liability or a fine. This unit is

factory equipped with a spark arrestor. If it requires

replacement, ask your LOCAL SERVICE DEALER to install the

Accessory Part #791-180890 Spark Arrestor Kit.

CALIFORNIA PROPOSITION 65 WARNING

P/N 769-01951A (12/06)

TABLE OF CONTENTS

Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . . . . . . .2

Oil and Fuel Information . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Starting/Stopping Instructions . . . . . . . . . . . . . . . . . . . . . .5

Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Maintenance and Repair Instructions . . . . . . . . . . . . . . . .7

Cleaning and Storage . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . .17-18

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E17

WARNING

THE ENGINE EXHAUST FROM THIS PRODUCT CONTAINS

CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO

CAUSE CANCER, BIRTH DEFECTS OR OTHER

REPRODUCTIVE HARM.

4-Cycle Gasoline Trimmer

Y26SS

READ ALL INSTRUCTIONS

BEFORE OPERATING

• Read the instructions carefully. Be familiar with the controls

and proper use of the unit.

• Do not operate this unit when tired, ill, or under the influence

of alcohol, drugs, or medication.

• Children and teens under the age of 15 must not use the

unit, except for teens guided by an adult.

• All guards and safety attachments must be installed properly

before operating the unit.

• Inspect the unit before use. Replace damaged parts. Check

for fuel leaks. Make sure all fasteners are in place and secure.

Replace parts that are cracked, chipped, or damaged in any

way. Do not operate the unit with loose or damaged parts.

• Carefully inspect the area before starting the unit. Remove

all debris and hard or sharp objects such as glass, wire, etc.

• Be aware of the risk of injury to the head, hands and feet.

• Clear the area of children, bystanders, and pets. At a

minimum, keep all children, bystanders, and pets outside a

50 feet (15 m.) radius; there still may be a risk to bystanders

from thrown objects. Bystanders should be encouraged to

wear eye protection. If you are approached, stop the unit

immediately.

• Use only 0.080 inch, 2.03 mm diameter original equipment

manufacturer replace-ment line. Never use metal-reinforced

line, wire or rope. These can break off and become

dangerous projectiles.

• Squeeze the throttle control and check that it returns

automatically to the idle position. Make all adjustments or

repairs before using unit.

SAFETY WARNINGS FOR GAS UNITS

• Store fuel only in containers specifically designed and

approved for the storage of such materials.

• Avoid creating a source of ignition for spilled fuel. Do not

start the engine until fuel vapors dissipate.

• Always stop the engine and allow it to cool before filling the

fuel tank. Never remove the fuel tank cap or add fuel when

the engine is hot. Never operate the unit without the fuel cap

securely in place. Loosen the fuel tank cap slowly to relieve

any pressure in the tank.

• Add fuel in a clean, well-ventilated outdoor area where there

are no sparks or flames. Remove the fuel cap slowly, and

only after the engine stops. Do not smoke while fueling.

Wipe up any spilled fuel from the unit immediately.

• Avoid creating a source of ignition for spilled fuel. Do not

start the engine until fuel vapors dissipate.

• Move the unit at least 30 feet (9.1 m) from the fueling source

and site before starting the engine. Do not smoke. Keep

sparks and open flames away from the area while adding

fuel or operating the unit.

WHILE OPERATING

• Never start or run the unit inside a closed room or building.

Breathing exhaust fumes can be fatal. Operate this unit only

in a well-ventilated outdoor area.

• Wear safety glasses or goggles that meet ANSI Z87.1

standards and are marked as such. Wear ear/hearing

protection when operating this unit. Wear a face or dust

mask if the operation is dusty.

• Wear heavy long pants, boots, gloves and a long sleeve

shirt. Do not wear loose clothing, jewelry, short pants,

sandals or go barefoot. Secure hair above shoulder level.

• The cutting attachment shield must always be in place while

operating the unit as a trimmer. Do not operate unit without

both trimming lines extended, and the proper line installed. Do

not extend the trimming line beyond the length of the shield.

• This unit has a clutch. The cutting attachment remains

stationary when the engine is idling. If it does not, have the

unit adjusted by an authorized service technician.

• Adjust the handle to your size in order to provide the best grip.

• Be sure the cutting attachment is not in contact with

anything before starting the unit.

• Use the unit only in daylight or good artificial light.

• Avoid accidental starting. Be in the starting position whenever

pulling the starter rope. The operator and unit must be in a stable

position while starting. Refer to Starting/Stopping Instructions.

• Use the right tool. Only use this tool for its intended purpose.

• Do not overreach. Always keep proper footing and balance.

• Always hold the unit with both hands when operating. Keep

a firm grip on both handles or grips.

• Keep hands, face, and feet at a distance from all moving

parts. Do not touch or try to stop the cutting attachment

when it rotates.

• Do not touch the engine, gear housing or muffler. These

parts get extremely hot from operation, even after the unit is

turned off.

• Do not operate the engine faster than the speed needed to

cut, trim or edge. Do not run the engine at high speed when

not cutting.

• Always stop the engine when cutting is delayed or when

walking from one cutting location to another.

• If you strike or become entangled with a foreign object, stop

the engine immediately and check for damage. Do not

operate before repairing damage. Do not operate the unit

with loose or damaged parts.

• Stop the unit, switch the engine to off, and disconnect the

spark plug for maintenance or repair.

• Use only original equipment manufacturer replacement parts

and accessories for this unit. These are available from your

authorized service dealer. Use of any unauthorized parts or

accessories could lead to serious injury to the user, or

damage to the unit, and void your warranty.

• Keep unit clean of vegetation and other materials. They may

become lodged between the cutting attachment and shield.

• To reduce fire hazard, replace a faulty muffler and spark

arrestor. Keep the engine and muffler free from grass,

leaves, excessive grease or carbon build up.

OTHER SAFETY WARNINGS

• Never store a fueled unit inside a building where fumes may

reach an open flame or spark.

• Allow the engine to cool before storing or transporting. Be

sure to secure the unit while transporting.

• Store the unit in a dry area, locked up or up high to prevent

unauthorized use or damage, out of the reach of children.

• Never douse or squirt the unit with water or any other liquid.

Keep handles dry, clean and free from debris. Clean after

each use, see Cleaning and Storage instructions.

• Keep these instructions. Refer to them often and use them

to instruct other users. If you loan someone this unit, also

loan them these instructions.

SAVE THESE INSTRUCTIONS

RULES FOR SAFE OPERATION

• IMPORTANT SAFETY INSTRUCTIONS •

WARNING: Gasoline is highly flammable, and its

vapors can explode if ignited. Take the following

precautions:

RULES FOR SAFE OPERATION

SYMBOL MEANING

• ON/OFF STOP CONTROL

ON / START / RUN

• WARNING - READ OPERATOR'S MANUAL

Read the operator’s manual(s) and follow all warnings

and safety instructions. Failure to do so can result in

serious injury to the operator and/or bystanders.

SAFETY AND INTERNATIONAL SYMBOLS

This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the

operator's manual for complete safety, assembly, operating and maintenance and repair information.

• ON/OFF STOP CONTROL

OFF or STOP

SYMBOL MEANING

• SAFETY ALERT SYMBOL

Indicates danger, warning or caution. May be used

in conjunction with other symbols or pictographs.

• WEAR EYE AND HEARING PROTECTION

WARNING: Thrown objects and loud noise can

cause severe eye injury and hearing loss. Wear eye

protection meeting ANSI Z87.1 standards and ear

protection when operating this unit. Use a full face

shield when needed.

• KEEP BYSTANDERS AWAY

WARNING: Keep all bystanders, especially

children and pets, at least 50 feet (15 m) from the

operating area.

• THROWN OBJECTS AND ROTATING CUTTER

CAN CAUSE SEVERE INJURY

WARNING: Do not operate without the cutting

attachment shield in place. Keep away from the

rotating cutting attachment.

• HOT SURFACE WARNING

Do not touch a hot muffler, gear housing or cylinder.

You may get burned. These parts get extremely hot

from operation. They remain hot for a short time after

the unit is turned off.

• UNLEADED FUEL

Always use clean, fresh unleaded fuel

• OIL

Refer to operator’s manual for the proper type of

oil.

• SHARP BLADE

WARNING: Sharp blade on cutting attachment

shield. To prevent serious injury, do not touch the

line cutting blade.

• CHOKE CONTROL

1. • FULL choke position

2. • PARTIAL choke position

3. • RUN choke position

OIL AND FUEL INFORMATION

RECOMMENDED OIL TYPE

Using the proper type and weight of oil in the crankcase is

extremely important. Check the oil before each use and

change the oil regularly. Failure to use the correct oil, or using

dirty oil, can cause premature engine wear and failure.

Use a high-quality SAE 30 weight oil of API (American

Petroleum Institute) service class SF, SG, SH.

ADDING OIL TO CRANKCASE: INITIAL USE

NOTE: This unit is shipped without oil. In order to avoid

damage to the unit, put oil in the crankcase before you

attempt to start the unit.

Your unit is supplied with one 3.04

fluid oz. (90 ml.) bottle of SAE 30

SF, SG, SH oil (Fig. 1).

NOTE: Save the bottle of oil. It

can be used to measure the

correct amount during future

oil changes. See Changing

the Oil.

1. Unscrew the top of the bottle of oil and remove the paper

WARNING: OVERFILLING OIL CRANKCASE MAY

CAUSE SERIOUS PERSONAL INJURY. Check and

maintain the proper oil level in the crank case; it is

important and cannot be overemphasized. Check the

oil before each use and change it as needed. See

Changing the Oil.

Fig. 1

Funnel

Spout

seal covering the

opening. Replace the

top. Next, cut the tip off

the funnel spout (Fig. 1).

2. Place the unit on a flat

level surface (Fig. 2).

3. Remove the dipstick from

the crankcase (Fig. 3).

4. Pour the entire bottle

of oil into the oil fill

hole (Fig. 3).

NOTE: Never add oil to

the fuel or fuel tank.

5. Wipe up any oil that

may have spilled and

reinstall the oil fill plug/

dipstick.

Check oil before each use and change as needed. Refer to

Checking the Oil Level.

RECOMMENDED FUEL TYPE

Old fuel is the primary reason for improper unit performance.

Be sure to use fresh, clean, unleaded gasoline.

NOTE: This is a four cycle engine. In order to avoid damage to

the unit, do not mix oil with gasoline.

Fig. 2

Oil Fill

Oil Fill Plug/

Dipstick

Oil Fill Hole

Fig. 3

O-Ring

Cutting

Attachment

Shield

Fuel

Cap

Throttle

Control

J-Handle

Cutting

Attachment

Shaft Grip

Primer

Bulb

Oil Fill Plug / Dipstick

Choke

Lever

Spark

Plug

Shaft

Housing

Starter Rope Grip

Line

Cutting

Blade

Spark

Plug

Muffler

Muffler Guard

Spark Arrestor

On/Off Stop

Control

KNOW YOUR UNIT

Air Filter

Cover

OIL AND FUEL INFORMATION

ASSEMBLY INSTRUCTIONS

Definition of Blended Fuels

Today's fuels are often a blend of gasoline and oxygenates

such as ethanol, methanol or MTBE (ether). Alcohol-blended

fuel absorbs water. As little as 1% water in the fuel can make

fuel and oil separate or form acids when stored. Use fresh fuel

(less than 60 days old), when using alcohol-blended fuel.

Using Blended Fuels

If you choose to use a blended fuel, or its use is unavoidable,

follow recommended precautions:

• Always use fresh unleaded gasoline

• Use the fuel additive STA-BIL

or an equivalent

• Drain tank and run the engine dry before storing unit

Using Fuel Additives

The use of fuel additives, such as STA-BIL

Gas Stabilizer or

an equivalent, will inhibit corrosion and minimize the formation

of gum deposits. Using a fuel additive can keep fuel from

forming harmful deposits in the carburetor for up to six (6)

months. Add 0.8 oz. (23 ml.) of fuel additive per gallon of fuel

according to the instructions on the container. NEVER add fuel

additives directly to the unit's gas tank.

FUELING THE UNIT

1. Remove the fuel cap (Fig. 4).

2. Place the gas container’s spout into the fill hole on the fuel

tank (Fig. 4) and fill the tank.

NOTE: Do not overfill the tank.

3. Wipe up any gasoline that may have spilled.

4. Reinstall the fuel cap.

5. Move the unit at least 30 ft. (9.1 m) from the fueling source

and site before starting the engine.

NOTE: Dispose of the old gasoline in accordance to Federal,

State and Local regulations.

WARNING: Add fuel in a clean, well ventilated

outdoor area. Wipe up any spilled fuel immediately.

Avoid creating a source of ignition for spilt fuel. Do

not start the engine until fuel vapors dissipate.

WARNING: Gasoline is extremely flammable.

Ignited vapors may explode. Always stop the engine

and allow it to cool before filling the fuel tank. Do not

smoke while filling the tank. Keep sparks and open

flames at a distance from the area.

WARNING:

Remove fuel cap slowly to avoid injury

from fuel spray. Never operate the unit without the

fuel cap securely in place

Fig. 4

Fuel Cap

Fuel Tank

Gas Can Spout

Unleaded

Gasoline

INSTALL AND ADJUST THE J-HANDLE

The Y26SS is equipped with a J-handle.

1. Place the J-handle between the top and middle clamp

pieces (Fig. 5).

2. While holding

the 3 pieces

together, install

the 4 screws

through the top

clamp and into

middle clamp.

NOTE: The holes

in the top and

middle clamp

will line up

only when

assembled correctly.

3. Place the clamps and the J-handle over the shaft housing

and onto the bottom clamp.

4. Hold each hex nut in the bottom clamp recess with a

finger. Start screws with a large Phillips screwdriver. Do

not tighten until you make the handle adjustment.

5. Slide the J-handle in or out until the arrow/white line on the

decal touches the clamp assembly (Fig. 5). You must first

loosen the screws if the handle is pre-installed.

6. While holding the unit in the operating position (Fig. 14),

position the J-handle to the location that provides you the

best grip.

7. Tighten the clamp screws evenly until tight.

Screws (4)

Top

Clamp

Middle Clamp

Bottom Clamp

Nuts

Fig. 5

Decal

J-Handle

Top Clamp

STARTING/STOPPING INSTRUCTIONS

STARTING INSTRUCTIONS

STOPPING INSTRUCTIONS

1. Release your hand from the throttle control. Allow the

engine to cool down by idling.

2. Put the On/Off Stop Control in the OFF (O) position.

1. Check the oil level in the crankcase. Refer to

Checking the Oil Level.

2. Fill the fuel tank with fresh, clean unleaded gasoline.

Refer to Fueling the Unit.

3. Make sure the On/Off Stop Control in the ON ( I )

position (Fig. 6).

4. Fully press and release the primer bulb 10 times,

slowly. Some amount of fuel should be visible in

the primer bulb and fuel lines (Fig. 7). If you can’t

see fuel in the bulb, press and release the bulb as

many times as it takes before you can see fuel in it.

5. Place the choke lever in Position 1 (Fig. 7).

6. Crouch in the starting position (Fig. 8) and squeeze

the throttle control. Pull the starter rope briskly 5

times.

7. Place the choke lever in Position 2 (Fig. 9).

8. While squeezing the throttle control , pull the starter

rope briskly 1 to 3 times to start the engine.

9. Keep the throttle squeezed and allow the engine to

warm up for 15 to 30 seconds.

10. Place the choke lever in Position 3 (Fig. 10). The

unit is ready for use.

IF...

The engine does not start, go back to step 4.

IF...

The engine fails to start after a few attempts, place

the choke lever in Position 3 and squeeze the

throttle control. Pull the starter rope briskly 3 to 8

times. The engine should start. If not, repeat.

IF WARM...

If the engine is already warm, make sure the

On/Off Stop control is in the ON position and start

the unit with the choke lever in Position 2. After the

unit starts, move the choke lever to Position 3.

WARNING: Avoid accidental starting. Make sure

you are in the starting position when pulling the

starter rope (Fig. 8).

To avoid serious injury, the

operator and unit must be in a stable position while

starting.

To avoid serious personal injury, ensure any Add-

On being used is installed correctly and secure

before starting the unit.

WARNING:

Operate this unit only in a well-

ventilated outdoor area. Carbon monoxide exhaust

fumes can be lethal in a confined area.

Fig. 6

Start / Stop

Control

Fig. 9

Fig. 10

Position 2

Position 3

APPLICATIONS

As a trimmer:

• Cutting grass and light weeds

• Edging

• Decorative trimming around trees, fences, etc.

Fig. 8

Starter Rope

Throttle Control

Fig. 7

Primer

Bulb

Choke Lever

OPERATING THE EZ-LINK

™

SYSTEM

The EZ-Link™ system enables the use of these optional Add-

Ons:

Trimmer/Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BT720r

Cultivator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GC720r

Edger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LE720r

Hedge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HT720r

Snow Thrower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST720r

Straight Shaft Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . SS725r

Tree Pruner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TP720r

Turbo Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TB720r

Pole Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PS720r

Removing the Cutting Attachment or Add-On

1. Turn the knob counterclockwise to loosen (Fig. 11).

2. Press and hold the release button (Fig. 11).

3. While firmly holding the upper shaft housing, pull the

cutting attachment or add-on straight out of the EZ-

Link™ coupler (Fig. 12).

Installing the Cutting Attachment or Add-On

NOTE: Place the unit on the ground or on a work bench to

make add-on installation or removal easier.

1. Turn knob counterclockwise to loosen (Fig. 11).

2. While firmly holding the add-on, push it straight into the

EZ-Link™ coupler (Fig. 12).

NOTE: Aligning the release button with the guide recess will

help installation (Fig. 11).

3. Turn the knob clockwise to tighten (Fig. 13).

For edging (when using the line head cutting attachment

with EZ-Link™ models), lock the release button of the

cutting attachment into the 90° edging hole (Fig. 13).

HOLDING THE TRIMMER

Before operating the unit, stand in the operating position (Fig.

14). Check for the following:

• The operator is wearing

eye protection and proper

clothing

• With a slightly-bent right

arm, the operator’s right

hand is holding the shaft

grip

• The operator’s left arm is

straight, the left hand

holding the assist handle

• The unit is at waist level

• The cutting attachment is

parallel to the ground and

easily contacts the grass

without the need to bend

over

OPERATING INSTRUCTIONS

WARNING: Prior to operation, read and

understand the operator’s manual for the add-on to

be used with this unit.

WARNING: To avoid serious personal injury and

damage to the unit, shut the unit off before

removing or installing add-ons.

Fig. 11

EZ-Link™ Coupler

Release Button

Guide Recess

Knob

Primary Hole

Upper Shaft Housing

EZ-Link™ Coupler

Fig. 12

Lower Shaft Housing

Release Button

Fig. 13

Knob

90˚ Edging Hole

(Trimmer Only)

CAUTION: Lock the release button in the primary

hole (Fig. 12) and securely tighten the knob before

operating this unit.

CAUTION: The add-ons with the coupler system is

to be used in the primary hole only. Using the wrong

hole could lead to personal injury or damage to the unit.

WARNING: Always wear eye, hearing, foot and

body protection to reduce the risk of injury when

operating this unit.

Fig. 14

MAINTENANCE SCHEDULE

Perform these required maintenance procedures at the

frequency stated in the table. These procedures should also be

a part of any seasonal tune-up.

NOTE: Some maintenance procedures may require special

tools or skills. If you are unsure about these procedures

take your unit to any non-road engine repair

establishment, individual or authorized service dealer.

WARNING: To prevent serious injury, never

perform maintenance or repairs with unit running.

Always service and repair a cool unit. Disconnect the

spark plug wire to ensure that the unit cannot start.

FREQUENCY MAINTENANCE REQUIRED SEE

Before starting engine

Fill fuel tank with fresh fuel

Check oil

p. 4

p. 9

Every 10 hours Clean and re-oil air filter p. 10

1st change at 10 hours

2nd change at 25 hours

Every 25 hours thereafter

Change oil

Clean spark arrestor

p. 10

p. 13

10 hours on new engine

Every 25 hours

Check rocker arm to valve clearance and adjust

Check spark plug condition and gap

p. 11

p. 12

ADJUSTING TRIMMING LINE LENGTH

The Bump Head™ cutting attachment allows you to release

trimming line without stopping the engine. To release more line,

lightly tap the cutting attachment on the ground (Fig. 15) while

operating the trimmer at high speed.

NOTE: Always keep the

trimming line fully

extended. Line release

becomes more

difficult as the cutting

line becomes shorter.

Each time the head is

bumped, about 1 inch

(25.4 mm) of trimming

line is released. A blade

in the cutting attachment shield will cut the line to the proper

length if excess line is released.

For best results, tap the Bump Head™ on bare ground or hard

soil. If line release is attempted in tall grass, the engine may

stall. Always keep the trimming line fully extended. Line release

becomes more difficult as the cutting line becomes shorter.

NOTE: Do not rest the Bump Head™ on the ground while the

unit is running.

Some line breakage will occur from:

• Entanglement with foreign matter

• Normal line fatigue

• Attempting to cut thick, stalky weeds

• Forcing the line into objects such as walls or fence posts

TIPS FOR BEST TRIMMING RESULTS

• For best trimming results, operate unit at full throttle.

• Keep the cutting attachment parallel to the ground.

• Do not force the cutting attachment. Allow the tip of the line to do

the cutting, especially along walls. Cutting with more than the tip

will reduce cutting efficiency and may overload the engine.

• Cut grass over 8 inches (200 mm) by working from top to bottom

in small increments to avoid premature line wear or engine drag.

• Cutting from right to left improves the unit's cutting efficiency.

Clippings are thrown away from the operator.

• Slowly move the trimmer into and out of the cutting area at the

desired height. Move either in a forward-backward or side-to-

side motion. Cutting shorter lengths produces the best results.

• Trim only when grass and weeds are dry.

• The life of your cutting line is dependent upon proper

adherence of explained trimming techniques, what

vegetation is cut, and where vegetation is cut.

For example, the line will wear faster when trimming against a

foundation wall as opposed to trimming around a tree.

DECORATIVE TRIMMING

Decorative trimming is

accomplished by removing

all vegetation around trees,

posts, fences and more.

Rotate the whole unit so

that the cutting attachment

is at a 30° angle to the

ground (Fig. 16).

OPERATING INSTRUCTIONS

WARNING: Do not remove or alter the line cutting

blade assembly. Excessive line length will make the

clutch overheat. This may lead to serious personal

injury or damage to the unit.

Fig. 16

Fig. 15

MAINTENANCE AND REPAIR INSTRUCTIONS

NOTE: Maintenance, replacement, or repair of the emission

control devices and system may be performed by any non-

road engine repair establishment, individual or authorized

service dealer.

MAINTENANCE AND REPAIR INSTRUCTIONS

SPEEDSPOOL

Always use original equipment manufacturer ™ 0.080 inch

(2.03 mm) replacement line. Lines other than those specified

may make the engine overheat or fail.

There are two methods to replace the SpeedSpool

trimming

line:

• Wind the inner reel with new line

• Install a pre-wound inner reel

Winding the Inner Reel With New Line

NOTE: It Is unnecessary to remove the bump knob to install a

new trimming line.

1. Cut two pieces of 0.080 inch (2.03 mm) trimming line, 10

feet (3 m) long.

2. Hold the outer spool and turn the inner reel counterclockwise

to line up the arrows on the outer spool and inner reel (Fig. 17).

3. Pull old line out of the line loading and line locking holes

(Fig. 18 and 19)

4. Insert a piece of trimming line straight into one of the two

eyelets in the outer spool. Push it up through the line

loading hole in

the inner reel

(Fig. 18). Do not

bend the line

when inserting it

into the eyelet.

5. Insert the line

into the locking

hole (Fig. 19).

Do not push the

line more than a

1/2 inch (12.7

mm) into the line

locking hole.

The line will form a small loop (Fig. 19) when it is inserted

correctly.

6. Pull the line from the outer spool until the line is tight

against the inner reel (Fig. 20).

7. Repeat procedures 4-6 with the second piece of line.

8. Hold the outer spool. Wind the inner reel counterclockwise

until approximately 4 inches (102 mm) of line remain (Fig. 21).

NOTE: Do not wind

the inner reel

before installing

the second piece

of line.

9. If winding the line

becomes difficult

or if the line jams,

pull the ends of

the line from the

spool (Fig. 22).

Continue winding

the inner reel

counterclockwise.

WARNING: Always use the correct line length

when installing trimming line on the unit. The line

may not release properly if the line is too long.

WARNING : Never use metal-reinforced line, wire,

chain or rope. These can break off and become

dangerous projectiles.

Top View Of The SpeedSpool

Outer Spool

Inner Reel

Fig. 17

Bump Knob

Arrows

Trimming Line

Line Loading Hole

Eyelet

Fig. 18

Line Locking Hole

Fig. 19

Fig.20

Fig. 21

Fig. 22

MAINTENANCE AND REPAIR INSTRUCTIONS

CHECKING THE OIL LEVEL

The importance of checking and maintaining the proper oil level

in the crankcase cannot be overemphasized. Check oil before

each use:

1. Stop the engine and allow oil to drain into the crankcase.

2. Place the unit on a flat, level surface to get a proper oil level

reading (Fig. 2).

3. Keep dirt, grass

clippings and other

debris out of the

engine. Clean the area

around the dipstick

before removing it.

4. Remove the oil fill

plug/dipstick and

wipe off oil. Reinsert it

all the way back in.

5. Remove the oil fill

plug/ dipstick and

check the oil level. Oil

should be up to the top

of the dipstick (Fig. 28).

6. If the level is low, add

a small amount of oil

to the oil fill hole and

recheck (Fig. 29).

Repeat this procedure

until the oil level

reaches the top of the

dipstick.

NOTE: Do not overfill the unit.

NOTE: Make sure the O-ring is in place on the oil fill

plug/dipstick when checking and changing the oil (Fig. 29).

INSTALLING A PRE-WOUND REEL

1. Turn the bump knob

counterclockwise and

remove the bump knob,

spring and foam seal

(Fig. 23).

2. Pull the old inner reel

with existing line from

the outer spool.

3. Insert the ends of the

prewound inner reel line

into the outer spool

eyelets (Fig. 24). Push

the new inner reel, arrow

side up, into the outer

spool.

4. Hold the inner reel in

place and install the

bump knob, spring and

foam seal. Press down

and turn the bump knob

clockwise. Grasp the

ends and pull firmly to

release the line from the

holding slots in the inner

reel (Fig. 23).

Releasing the Inner Reel

If the SpeedSpool

does not

release line correctly, pull the

ends of the line firmly from

the spool (Fig. 22). If this

does not the release line,

follow the Cleaning the

SpeedSpool

instructions.

CLEANING THE SPEEDSPOOL

Cleaning the SpeedSpool

may be

necessary if:

• A jammed or excessive line

must be removed

• The SpeedSpool

becomes

difficult to wind or does not

operate correctly when

bumping the head on the

ground

1. Hold the outer spool, and

unscrew the bump knob

counterclockwise (Fig. 25).

2. Pull out the bump knob, spring and foam seal (Fig. 23).

3. Pull the inner reel with existing line from the outer spool (Fig. 24).

4. Remove any existing line from the inner reel before

cleaning. Remove any

debris or grass from the

knob, spring, inner reel

and foam seal. Wash the

inner reel with warm

soapy water (Fig. 26).

5. Clean the shaft and the

inner surface of the outer

spool. To clean the shaft

underneath the plunger,

press down on the

plunger (Fig. 27). Remove

any dirt or debris from the

shaft.

NOTE: The inner reel must

be totally dry before

reinstalling it into the

outer spool. Do not

lubricate the inner reel or

outer spool assembly.

6. Place the inner reel into

the outer spool.

7. Place the bump knob,

spring and foam seal into

the inner reel (Fig. 23).

8. Press the bump knob down and tighten clockwise.

9. Install new line as described in Line Installation for the

SpeedSpool

Bump Knob

Foam Seal

Spring

Inner

Reel

Fig. 23

Fig. 24

Fig. 25

Inner

Reel

Fig. 26

Shaft

Plunger

Fig. 27

CAUTION: To prevent extensive engine wear and

damage to the unit, always maintain the proper oil

level in the crankcase. Never operate the unit with

the oil level below the bottom of the dipstick.

Top of Dipstick

O-Ring

Oil Fill Plug/Dipstick

Fig. 28

Full

Add 1.4-

1.5 Oz.

(41-44 ml)

Fig. 29

Oil Fill Plug/

Dipstick

Oil Fill Hole

O-Ring

MAINTENANCE AND REPAIR INSTRUCTIONS

CHANGING THE OIL

For a new engine, change the oil after the first 10 hours of

operation. Change the oil while the engine is still warm. The oil will

flow freely and carry away more impurities.

1. Unplug spark plug boot to prevent accidental starting.

2. Remove the oil fill plug/dipstick.

3. Pour the oil out of the

oil fill hole and into a

container by tipping the

unit to a vertical

position (Fig. 30). Allow

ample time for

complete drainage.

4. Wipe up any oil residue

on the unit and clean

up any oil that may

have spilled. Dispose of

the oil according to

Federal, State and local

regulations.

5. Refill the crankcase

with 3.04 fluid ounce

(90 ml) of SAE 30 SF, SG, SH oil.

NOTE: Use the bottle and spout saved from initial use to

measure the correct amount of oil. The top of the label on

the bottle measures approximately 3.04 ounces (90 ml) (Fig.

31). Check the level with the dipstick. If the level is low, add

a small amount of oil and recheck. Do not overfill (Fig. 31).

6. Replace the oil fill plug/dipstick.

7. Reconnect the spark plug boot.

AIR FILTER MAINTENANCE

Cleaning the Air Filter

Clean and re-oil the air filter every 10 hours of operation. It is

an important item to maintain. Failure to maintain your air filter

properly can result in poor performance or can cause

permanent damage to your engine.

1. Open the air filter cover. Push the tab on the right side of

the cover inward. Then pull the air filter cover out and to

the left (Fig. 32).

WARNING: Wear gloves to prevent injury when

handling unit.

Fig. 30

Fill Level

Fig. 31

NOTE: It may be necessary to

remove the fuel cap to

completely remove the air filter

cover.

2. Remove the air filter (Fig. 32).

3. Wash the filter in detergent and

water (Fig. 33). Rinse the filter

thoroughly and allow it to dry.

4. Apply enough clean SAE 30

motor oil to lightly coat the filter

(Fig. 34).

5. Squeeze the filter to spread

and remove excess oil (Fig. 35).

6. Replace the filter

(Fig. 36).

NOTE: If the unit is

operated without

the air filter, you

will VOID the

warranty.

7. Reinstall the air

filter cover.

Position the

hooks on the left

side of the air

filter cover into

the slots at the left side of the back plate (Fig. 36).

NOTE: It may be necessary to remove the fuel cap to reinstall

the air filter cover.

8. Swing the cover to the right until the tab on the air filter

cover snaps into place in the slot on the back plate (Fig. 37).

9. Replace the fuel cap if it was removed.

WARNING: To avoid serious personal injury,

always turn the unit off and allow it to cool before

you clean or service it.

Fig. 33

Air Filter

Air Filter Cover

Tab

Fig. 32

Fig. 34

Fig. 35

Fig. 36

Back Plate Slot

Slots

Back Plate

Checking the fuel, cleaning the air filter, and adjusting the idle

speed should solve most engine problems. If not and all of the

following are true:

• the engine will not idle

• the engine hesitates or stalls on acceleration

• there is a loss of engine power

Have the carburetor adjusted by an authorized service dealer.

ROCKER ARM CLEARANCE

This requires disassembly of the engine. If you feel unsure or

unqualified to perform this, take the unit to an authorized

service center.

NOTE: Inspect the valve to rocker arm clearance with a feeler

gauge after the first 10 hours of operation and then every

25 hours of operation thereafter.

• The engine must be cold when checking or adjusting the

valve clearance.

• This task should be performed inside, in a clean, dust free

area.

1. Remove the muffler cover by pressing down on it,

separating it from the engine cover. Using a flat blade

screwdriver, disengage the middle and front tabs and slots

first. The cover will hinge off from the rear tab (Fig. 39).

2. Remove the two (2) screws on top of the engine cover with a

Flat-head or T-25 Torx screwdriver (Fig. 40).

CARBURETOR ADJUSTMENT

The idle speed of the engine is adjustable. An idle adjustment

screw is reached though a hole in the top of the engine cover

(Fig. 38).

NOTE: Careless

adjustments can

seriously damage your

unit. An authorized

service dealer should

make carburetor

adjustments.

Check Fuel

Old fuel is usually the

reason for improper unit

performance. Drain and

refill the tank with fresh fuel

prior to making any adjustments. Refer to Oil and Fuel

Information.

Clean Air Filter

The condition of the air filter is important to the operation of the

unit. A dirty air filter will restrict air flow. This is often mistaken

for an out of adjustment carburetor. Check the condition of the

air filter before adjusting the idle speed screw. Refer to Air

Filter Maintenance.

Adjust Idle Speed Screw

If, after checking the fuel and cleaning the air filter, the engine

still will not idle, adjust the idle speed screw as follows:

1. Start the engine and let it run at a high idle for a minute to

warm up. Refer to Starting/Stopping Instructions.

2. Release the throttle trigger and let the engine idle. If the

engine stops, insert a small phillips into the hole in the air

filter/muffler cover (Fig. 38). Turn the idle speed screw in,

clockwise, 1/8 of a turn at a time (as needed) until the engine

idles smoothly.

NOTE: The cutting attachment should not rotate when the

engine idles.

3. If the cutting attachment rotates when the engine idles, turn

the idle speed screw counterclockwise 1/8 of a turn at a

time (as needed), to reduce idle speed.

MAINTENANCE AND REPAIR INSTRUCTIONS

WARNING: The cutting attachment may spin during

idle speed adjustments. Wear protective clothing and

observe all safety instructions to prevent serious

personal injury.

WARNING: To prevent serious personal injury,

make sure the cutting attachment has stopped

rotating before you turn it off and set it down.

Idle Adjustment Screw

Fig. 38

Fig. 39

Engine Cover

Front Slot

Front Tab

Middle Tab

Middle Slot

Rear Slot

and Tab

Remove

Screws

Engine Cover

Fig. 40

Muffler

Top View Of The Engine

Air Filter

Cover

Tab

Fig. 37

3. Remove the screw behind

the engine cover (Fig. 41).

4. Disconnect the spark plug

wire.

5. Clean dirt from around the

spark plug. Remove the

spark plug from the cylinder

head by turning a 5/8 in.

socket counterclockwise.

6. Remove the engine cover

(Fig. 40).

7. Clean dirt from around the

rocker arm cover. Remove

the screw holding the rocker

arm cover with a large flat

blade screwdriver or Torx T-

25 bit (Fig. 42). Remove the

rocker arm cover and gasket.

8. Pull the starter rope slowly to

bring the piston to the top of its

travel, (known as top dead

center). Check that:

• The piston is at the top of its

travel while looking in the

spark plug hole (Fig. 42)

• Both rocker arms move

freely, and both valves are

closed

If these statements are not true, repeat this step.

9. Slide the feeler gauge between the rocker arm and the

valve return spring. Measure the clearance between the

valve stem and rocker arm (Fig. 43). Measure both the

intake and exhaust valves.

The recommended clearance for both intake and exhaust is

.003 – .006 in. (.076 – 0.152 mm). Use a standard automotive

.005 in. (0.127 mm) feeler gauge. The feeler gauge should slide

between the rocker arm and valve stem with a slight amount of

resistance, without binding. See Figures 43 and 44.

10. If the clearance is not within specification:

a. Turn the adjusting nut using a 5/16 inch (8 mm) wrench or

nut driver (Fig. 44).

• To increase clearance, turn the adjusting nut

counterclockwise.

MAINTENANCE AND REPAIR INSTRUCTIONS

Fig. 44

• To decrease clearance, turn the adjusting nut

clockwise.

b. Recheck both clearances, and adjust as necessary.

11. Reinstall the rocker arm cover using a new gasket. Torque

the screw to 20–30 in•lb (2.2–3.4 N•m).

12. Reinstall the engine cover. Check alignment of the cover

before tightening the screws. Tighten screws.

13. Reinstall the muffler cover. Slip the rear tab on the muffler

cover into the engine cover rear slot. Then slide the

remaining slots into the tabs until they snap into place

(Fig. 39).

14. Check the spark plug and reinstall. See Replacing the

Spark Plug.

15. Replace the spark plug wire.

REPLACING THE SPARK PLUG

Use a replacement part number 791-180852B spark plug. The

correct air gap is 0.025 in. (0.635 mm.). Remove the plug after

every 25 hours of operation and check its condition.

1. Stop the engine and allow it to cool. Grasp the plug wire

firmly and pull the cap from the spark plug.

2. Clean dirt from around the spark plug. Remove the spark

plug from the cylinder head by turning a 5/8 in. socket

counterclockwise.

3. Replace cracked, fouled or

dirty spark plug. Set the air

gap at 0.025 in. (0.635 mm.)

using a feeler gauge (Fig. 45).

4. Install a correctly-gapped

spark plug in the cylinder

head. Turn the 5/8 in.

socket clockwise until snug.

If using a torque wrench torque

to:

110-120 in.•lb. (12.3-13.5 N•m)

Do not over tighten.

Feeler Gauge

Adjusting Nut

Rocker Arm

.003–.006 in.

(.076–.152 mm)

Valve Stem

Screw

Fig. 41

Rocker

Arm

Cover

Fig. 42

Spark

Plug

Hole

Adjusting Nuts

Feeler Gauge

Rocker Arms

Fig. 43

INTAKE

EXHAUST

0.025 in.

(0.635 mm.)

Fig. 45

WARNING: Do not sand blast, scrape or clean

electrodes. Grit in the engine could damage the

cylinder.

SPARK ARRESTOR MAINTENANCE

1. Remove the muffler cover. See Rocker Arm Clearance.

2. With a flat blade screwdriver or Torx T-20 bit, remove the

screw attaching the spark arrestor cover to the muffler

(Fig. 46).

3. Pull the tab on the spark arrestor cover out of the muffler.

Remove the spark arrestor cover.

4. Remove the spark arrestor screen from the spark arrestor

cover.

5. Clean the spark arrestor screen with a wire brush or

replace it.

6. Reinstall the spark arrestor screen, spark arrestor cover

and screw.

CLEANING

Use a small brush to clean off the outside of the unit. Do not

use strong detergents. Household cleaners that contain

aromatic oils such as pine and lemon, and solvents such as

kerosene, can damage plastic housing or handle. Wipe off any

moisture with a soft cloth.

STORAGE

• Never store the unit with fuel in the tank where fumes may

reach an open flame or spark.

• Allow the engine to cool before storing.

• Lock up the unit to prevent unauthorized use or damage.

• Store the unit in a dry, well-ventilated area.

• Store the unit out of the reach of children.

LONG TERM STORAGE

1. Drain all gasoline from the gas tank into a container. Do

not use gas that has been stored for more than 60 days.

Dispose of the old gasoline in accordance to Federal,

State, and Local regulations.

2. Start the engine and allow it to run until it stalls. This

ensures that all gasoline has been drained from the

carburetor.

3. Allow the engine to cool. Remove the spark plug and put 5

drops of high quality motor oil into the cylinder. Pull the

starter rope slowly to distribute the oil. Reinstall the spark

plug.

NOTE: Remove the spark plug and drain all of the oil from the

cylinder before attempting to start the trimmer after

storage.

4. Change the oil, referring to Changing the Oil. Dispose of

the old oil in accordance to Federal, State and Local

regulations.

5. Thoroughly clean the unit and inspect for any loose or

damaged parts. Repair or replace damaged parts and

tighten loose screws, nuts or bolts. The unit is ready for

storage.

TRANSPORTING

• Allow the engine to cool before transporting.

• Secure the unit while transporting.

• Drain the gas tank before transporting.

• Tighten gas cap before transporting.

MAINTENANCE AND REPAIR INSTRUCTIONS

WARNING: To avoid serious personal injury,

always turn your unit off and allow it to cool before

you clean or service it.

Fig. 46

Muffler

Spark Arrestor Screen

Spark Arrestor Cover

Screw

Tab

Slot

TROUBLESHOOTING

If further assistance is required, contact your authorized service dealer.

CAUSE ACTION

Cutting attachment bound with grass Stop the engine and clean cutting attachment

Cutting attachment out of line Refill with new line

Inner reel bound up Replace the inner reel

Cutting head dirty Clean inner reel and outer spool

Line welded Disassemble, remove the welded section and rewind

Line twisted when refilled Disassemble and rewind the line

Not enough line is exposed Push the bump knob and pull out line until 4 inches (102 mm)

of line is outside of the cutting attachment

CAUSE ACTION

Old fuel Drain gas tank and add fresh fuel

Improper carburetor adjustment Take to an authorized service dealer for adjustment

Fouled spark plug Replace or clean the spark plug

Plugged spark arrestor Clean or replace spark arrestor

CAUSE ACTION

On/Off control in the STOP position

Turn On/Off control to ON

Empty fuel tank Fill fuel tank with new fuel

Primer bulb wasn't pressed enough Press primer bulb fully and slowly 10 times

Old fuel Drain gas tank and add fresh fuel

Fouled spark plug Replace or clean the spark plug

Plugged spark arrestor Clean or replace spark arrestor

ENGINE WILL NOT START

ENGINE WILL NOT IDLE

ENGINE WILL NOT ACCELERATE

ENGINE LACKS POWER OR STALLS WHEN CUTTING

CAUSE ACTION

Air filter is plugged Replace or clean the air filter

Old fuel Drain gas tank and add fresh fuel

Improper carburetor adjustment Adjust carburetor

CAUSE ACTION

Old fuel Drain gas tank and add fresh fuel

Improper carburetor adjustment Take to an authorized service dealer for adjustment

Cutting attachment bound with grass Stop the engine and clean the cutting attachment

Dirty air filter Clean or replace the air filter

Plugged spark arrestor Clean or replace spark arrestor

CUTTING ATTACHMENT WILL NOT ADVANCE LINE

CAUSE ACTION

Oil, cleaner or lubricant in cutting head Clean and thoroughly dry the cutting head

CUTTING LINE ADVANCES UNCONTROLLABLY

SPECIFICATIONS

ENGINE*

*All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes

at any time without notice.

Engine Type.................................................................................................................................................................. Air-Cooled, 4-Cycle

Displacement................................................................................................................................................................. 1.6 cu. in. (26.2 cc)

Operating RPM ........................................................................................................................................................................... 7,200+ rpm

Idle Speed RPM .............................................................................................................................................................. 2,800 - 3,600 rpm

Ignition Type.................................................................................................................................................................................. Electronic

Ignition Switch .......................................................................................................................................................... Positive On/Off Switch

Valve clearance...................................................................................................................................... 0.003–0.006 in. (0.076–0.152 mm)

Spark Plug Gap ........................................................................................................................................................ 0.025 inch (0.635 mm)

Lubrication ................................................................................................................................................................................... SAE 30 Oil

Crankcase Oil Capacity ........................................................................................................................................................ 3.04 oz (90 ml)

Fuel ............................................................................................................................................................................................... Unleaded

Carburetor ............................................................................................................................................................... Diaphragm, All-Position

Starter ....................................................................................................................................................................................... Auto Rewind

Muffler ............................................................................................................................................................................. Baffled with Guard

Throttle ....................................................................................................................................................................... Manual Spring Return

Fuel Tank Capacity ................................................................................................................................................................. 12 oz (355 ml)

Drive Shaft Housing ..................................................................................................................................................................... Steel Tube

Throttle Control ................................................................................................................................................................ Finger-Tip Trigger

Approximate Unit Weight (No fuel, with handle, cutting attachment and shield) ...................................................... 12-13.5 lbs (5.4-6 kg)

Cutting Mechanism ....................................................................................................................... Speed Spool

Dual String Cutting Head

Line Spool..................................................................................................................................................................... Bump Line Releaser

Line Spool Diameter ...................................................................................................................................................... 3 inches (76.2 mm)

Trimming Line Diameter.......................................................................................................................................... 0.080 inches (2.03 mm)

Cutting Path Diameter ................................................................................................................................................ 17 inches (43.18 cm)

DRIVE SHAFT AND CUTTING ATTACHMENT*

NOTES

California / EPA Emission Control Warranty Statement

Your Warranty Rights and Obligations

The California Air Resources Board, the Environmental Protection Agency and MTD LLC (MTD) are pleased to explain the emission

control system warranty on your 2005 and later small off-road engine. New small off-road engines must be designed, built and

equipped to meet stringent anti-smog standards. MTD must warrant the emission control system on your small off-road engine for

the periods of time listed below provided there has been no abuse, neglect or improper maintenance of your small off-road engine.

Your emission control system may include parts such as the carburetor or fuel-injected system, the ignition system, and catalytic

converter. Also included may be hoses, belts, connectors and other emission-related assemblies.

Where a warrantable condition exists, MTD will repair your small off-road engine at no cost to you including diagnosis, parts and

labor.

The 2005 and later small off-road engines are warranted for two years. If any emission-related part on your engine is defective, the

part will be repaired or replaced my MTD.

Owners Warranty Responsibilities

• As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in your operator’s

manual. MTD recommends that you retain all receipts covering maintenance on your small off-road engine, but MTD cannot deny

warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.

• As the small off-road engine owner, you however should be aware that MTD may deny you warranty coverage if your small off-road

engine or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications.

• You are responsible for presenting your small off-road engine to a MTD Authorized Service Center as soon as a problem exists. The

warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should call 1-800-800-7310.

Manufacturer’s Warranty Coverage

• The warranty period begins on the date the engine or equipment is delivered to the retail purchaser.

• The manufacturer warrants to the initial owner and each subsequent purchaser, that the engine is free from defects in material and

workmanship which cause the failure of a warranted part for a period of two years.

• Repair or replacement of warranted part will be performed at no charge to the owner at an Authorized MTD Service Center. For the

nearest location please contact MTD at: 1-800-800-7310.

• Any warranted part which is not scheduled for replacement, as required maintenance or which is scheduled for only for regular

inspection to the effect of “Repair or Replace as Necessary” is warranted for the warranty period. Any warranted part which is

scheduled for replacement as required maintenance will be warranted for the period of time up to the first scheduled replacement

point for that part.

• The owner will not be charged for diagnostic labor which leads to the determination that a warranted part is defective, if the

diagnostic work is performed at an Authorized MTD Service Center.

• The manufacturer is liable for damages to other engine components caused by the failure of a warranted part still under warranty.

• Failures caused by abuse, neglect or improper maintenance are not covered under warranty.

• The use of add-on or modified parts can be grounds for disallowing a warranty claim. The manufacturer is not liable to cover failures

of warranted parts caused by the use of add-on or modified parts.

• In order to file a claim, go to your nearest Authorized MTD Service Center. Warranty services or repairs will be provided at all

Authorized MTD Service Centers.

• Any manufacturer approved replacement part may be used in the performance of any warranty maintenance or repair of emission

related parts and will be provided without charge to the owner. Any replacement part that is equivalent in performance or durability

may be used in non-warranty maintenance or repair and will not reduce the warranty obligations of the manufacturer

• The following components are included in the emission related warranty of the engine, air filter, carburetor, primer, fuel lines, fuel

pick up/ fuel filter, ignition module, spark plug and muffler.

MANUFACTURER’S LIMITED WARRANTY FOR:

No implied warranty, including any implied warranty of

merchantability or fitness for a particular purpose, applies

after the applicable period of express written warranty

above as to the parts as identified. No other express

warranty or guaranty, whether written or oral, except as

mentioned above, given by any person or entity, including

a dealer or retailer, with respect to any product shall bind

MTD. During the period of the Warranty, the exclusive

remedy is repair or replacement of the product as set forth

above. (Some states do not allow limitations on how long an

implied warranty lasts, so the above limitation may not apply

to you.)

The provisions as set forth in this Warranty provide the

sole and exclusive remedy arising from the sales. MTD

shall not be liable for incidental or consequential loss or

damages including, without limitation, expenses incurred

for substitute or replacement lawn care services, for

transportation or for related expenses, or for rental

expenses to temporarily replace a warranted product.

(Some states do not allow limitations on how long an implied

warranty lasts, so the above limitation may not apply to you.)

In no event shall recovery of any kind be greater than the

amount of the purchase price of the product sold. Alteration of

the safety features of the product shall void this Warranty. You

assume the risk and liability for loss, damage, or injury to you

and your property and/or to others and their property arising

out of the use or misuse or inability to use the product.

This limited warranty shall not extend to anyone other than the

original purchaser, original lessee or the person for whom it

was purchased as a gift.

How State Law Relates to this Warranty: This warranty gives

you specific legal rights, and you may also have other rights

which vary from state to state.

To locate your nearest service dealer dial 1-800-800-7310 in

the United States or 1-800-668-1238 in Canada.

MTD LLC

P.O. Box 361131

Cleveland, OH 44136-0019

The limited warranty set forth below is given by MTD LLC

(“MTD”) with respect with new merchandise purchased and

used in the United States, its possessions and territories.

MTD warrants this product against defects in material and

workmanship for a period of two (2) years commencing on the

date of original purchase and will, at its option, repair or

replace, free of charge, any part found to be defective in

material or workmanship. This limited warranty shall only apply

if this product has been operated and maintained in

accordance with the Operator’s Manual furnished with the

product, and has not been subject to misuse, abuse,

commercial use, neglect, accident, improper maintenance,

alteration, vandalism, theft, fire, water or damage because of

other peril or natural disaster. Damage resulting from the

installation or use of any accessory or attachment not

approved by MTD for use with the product(s) covered by this

manual will void your warranty as to any resulting damage.

This warranty is limited to ninety (90) days from the date of

original retail purchase for any MTD product that is used for

rental or commercial purposes, or any other income-producing

purpose.

HOW TO OBTAIN SERVICE: Warranty service is available,

WITH PROOF OF PURCHASE THROUGH YOUR LOCAL

AUTHORIZED SERVICE DEALER. To locate the dealer in your

area, please check for a listing in the Yellow Pages or contact

the Customer Service Department of MTD LLC by calling 1-

800-800-7310 or writing to P.O. Box 361131, Cleveland OH

44136-0019 or if in Canada call 1-800-668-1238. No product

returned directly to the factory will be accepted unless prior

written permission has been extended by the Customer

Service Department of MTD.

This limited warranty does not provide coverage in the

following cases:

A. Tune-ups - Spark Plugs, Carburetor Adjustments, Filters

B. Wear items - Bump Knobs, Outer Spools,Cutting Line,

Inner Reels, Starter Pulley,Starter Ropes, Drive Belts

C. MTD does not extend any warranty for products sold or

exported outside of the United States of America, its

possessions and territories, except those sold through

MTD’s authorized channels of export distribution.

MTD reserves the right to change or improve the design of any

McCulloch Product without assuming any obligation to modify

any product previously manufactured.

Manuel de L’utilisateur

Désherbeuse à gaz à 4-temps

Y26SS

SAVE THESE INSTRUCTIONS

Obtenez la liste des concessionnaires agréés appelez le 1-800-

800-7310 aux États-Unis ou le 1-800-668-1238 au Canada.

Pour de plus amples informations à propos de votre appareil,

visitez www.yardmachines.com.

NE RETOURNEZ PAS L'APPAREIL AU DÉTAILLANT CHEZ QUI

VOUS L'AVEZ ACHETÉ. TOUT SERVICE SOUS GARANTIE

NÉCESSITE UNE PREUVE D'ACHAT.

CE PRODUIT EST COUVERT PAR UN OU PLUSIEURS

BREVETS AMÉRICAINS, ET D’AUTRES SONT EN INSTANCE.

Toutes les informations, illustrations et spécifications contenues

dans ce manuel tiennent compte des dernières informations

techniques disponibles au moment de mettre sous presse. Nous

nous réservons le droit d'y apporter des modifications à tout

moment, sans préavis.

réservés.

AVERTISSEMENT: Lorsque vous utilisez la machine,

vous devez suivre les consignes de sécurité. Veuillez lire

ces instructions avant d’opérer la machine pour vous

assurer de la sécurité de l’opérateur et de tout spectateur.

Veuillez conserver ces instructions pour un usage ultérieur.

PARE-ÉTINCELLES

REMARQUE : à l'intention des utilisateurs opérant dans les

terres forestières des États-Unis et dans les états de

Californie, du Maine, de l'Orégon et de Washington. Toutes

les terres forestières des États-Unis et de l'état de Californie

(Codes sur les ressources publiques 4442 et 4443), de l'Orégon

et de Washington exigent de par la loi que certains moteurs à

combustion interne utilisés dans des zones couvertes de taillis

ou d'herbe soient équipés d'un pare-étincelles en parfait état de

fonctionnement, ou qu'ils soient conçus, équipés et entretenus

pour la prévention des incendies. Renseignez-vous auprès des

autorités de votre province ou de votre municipalité concernant

la réglementation en vigueur. Vous pourriez être passible d'une

amende ou être tenu responsable si vous ne respectez pas cette

réglementation. Cet appareil est équipé d'un pare-étincelles en

usine. Si l'écran pare-étincelles, réf. 791-180890, doit être

remplacé, communiquez avec le service technique.

AVERTISSEMENT DE LA PROPOSITION 65 DE CALIFORNIE

P/N 769-01951A (12/06)

TABLE DES MATIÈRES

Service technique . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F1

Consignes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . .F2

Informations sur l'huile et le carburant . . . . . . . . . . . . . .F3

Instructions de montage . . . . . . . . . . . . . . . . . . . . . . . . .F4

Familiarisez-vous avec votre appareil . . . . . . . . . . . . . . .F4

Instructions de démarrage et d'arrêt . . . . . . . . . . . . . . . .F5

Mode d'emploi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F6

Entretien et réparations . . . . . . . . . . . . . . . . . . . . . . . . . .F7

Nettoyage et entreposage . . . . . . . . . . . . . . . . . . . . . . .F13

Tableau de dépannage . . . . . . . . . . . . . . . . . . . . . . . . .F14

Caractéristiques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F15

Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F16-F17

Liste des pièces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E17

AVERTISSEMENT

LES GAZ D'ÉCHAPPEMENT DU MOTEUR DE CET APPAREIL

CONTIENNENT DES PRODUITS CHIMIQUES CONSIDÉRÉS PAR

L'ÉTAT DE CALIFORNIE COMME POUVANT CAUSER LE

CANCER, DES MALFORMATIONS CONGÉNITALES OU D'AUTRES

EFFETS NOCIFS SUR L'APPAREIL DE REPRODUCTION.

• IMPORTANTES CONSIGNES DE SÉCURITÉ •

LIRE TOUTES LES INSTRUCTIONS

AVANT UTILISATION

• Veuillez lire les instructions avec soin. Familiarisez-vous avec les

commandes et l'utilisation correcte de cet appareil.

• N'utilisez pas l'appareil si vous êtes fatigué, malade ou sous l'effet

de l'alcool, de drogues ou de médicaments.

• Les enfants et adolescents de moins de 15 ans ne doivent pas utiliser

l'appareil exceptés les adolescents assistés d'un adulte.

• Inspectez l'appareil avant utilisation. Remplacez les pièces endommagées.

Regardez s'il y a des fuites de carburant. Assurez-vous que les fixations

sont solidement en place. Remplacez les pièces de l'accessoire de coupe

qui sont fendillées, ébréchées ou endommagées. Assurez-vous que

l'accessoire de coupe est correctement installé et solidement fixé. Assurez-

vous que le protecteur d'accessoire de coupe est correctement fixé et

positionné comme recommandé. Vous risquez sinon de causer des

blessures à l'opérateur et aux spectateurs, et d'endommager l'appareil.

• N'utilisez que du fil de remplacement d’origine du fabricant de 2,03

mm, 0,080 po de diamètre. N'utilisez jamais de fil, de chaîne ou de

cordon à renfort métallique car ils peuvent se briser et se

transformer en projectile dangereux.

• Soyez conscient des risques de blessure à la tête, aux mains et aux

pieds.

• Dégagez la zone de coupe avant chaque usage. Enlevez tous les

objets pouvant être projetés ou happés par l'accessoire de coupe :

cailloux, verre brisé, clous, fil ou ficelle. Éloignez enfants, spectateurs

et animaux de la zone de coupe. Tenez-les à au moins 15 m (50 pi) de

là mais sachez que les spectateurs risquent quand même d'être

atteints par des objets projetés. Les spectateurs doivent porter des

protections oculaires. Arrêtez immédiatement le moteur et

l'accessoire de coupe si quelqu'un s'approche de vous.

• Appuyez sur la manette des gaz et assurez-vous qu'elle revient

automatiquement en position de ralenti. Procédez à tous les

réglages ou réparations avant d'utiliser l'appareil.

AVERTISSEMENTS DE SÉCURITÉ CONCERNANT LES

DÉSHERBEUSES À GAZ

• Ne stockez le carburant que dans des contenants spécialement

conçus et homologués pour le stockage de ce type de matières.

• Arrêtez toujours le moteur et laissez-le refroidir avant de remplir le

réservoir de carburant. N'enlevez jamais le bouchon du réservoir et

n'ajoutez jamais de carburant pendant que le moteur est chaud. Ne

faites jamais fonctionner l'appareil sans que le bouchon de carburant

soit bien mis. Desserrez lentement le bouchon afin de réduire la

pression du réservoir.

• Évitez de créer une source d'allumage pour le carburant déversé. Ne

démarrez pas le moteur avant que les vapeurs de carburant ne se

soient dissipées.

• Ajoutez le carburant dans un endroit bien aéré et propre en plein air

à l'abri des étincelles ou des flammes. N'enlevez lentement le

bouchon du réservoir d'essence qu'après avoir arrêté le moteur. Ne

fumez pas pendant le remplissage de carburant. Essuyez

immédiatement tout déversement de carburant de l'appareil.

• Éloignez l'appareil d'au moins 9.1 m (30 pi) de la source de ravitaillement

en carburant avant de démarrer le moteur. Ne fumez pas et éloignez toute

source d'étincelles ou de flammes vives du lieu de ravitaillement ou de

fonctionnement de l'appareil.

PENDANT L'UTILISATION DE L'APPAREIL

• Évitez de démarrer ou de faire marcher l'appareil à l'intérieur d'une

pièce ou d'un bâtiment fermé. La respiration de fumées

d'échappement peut tuer. Ne faites fonctionner cet appareil qu'à

l'extérieur dans un endroit bien aéré.

• Portez des lunettes de sécurité conformes aux normes ANSI Z87.1

ainsi que des protège-oreilles durant l'utilisation de l'appareil. Portez

un masque facial ou antipoussières si vous travaillez dans un lieu

poussiéreux.

• Portez des pantalons épais et longs, des bottes, des gants et une

chemise à manches longues. Ne marchez pas pieds nus et évitez

les vêtements lâches, bijoux, pantalons courts et sandales. Relevez

les cheveux au-dessus des épaules.

• Le protecteur d'accessoire de coupe doit toujours être en place lors

de l'utilisation de l'appareil. Ne faites pas marcher l'appareil sans

que les deux fils soient bien déployés, en supposant qu'un fil

approprié a été installé. Assurez-vous que le fil ne dépasse pas le

protecteur de sécurité.

• Cet appareil est muni d'un embrayage. L'accessoire de coupe reste

stationnaire lorsque le moteur est au ralenti. Si ce n'est pas le cas,

faites régler l'appareil par un technicien agréé.

• Ajustez la poignée selon votre taille pour mieux l'agripper.

• N'utilisez l'appareil qu'en plein jour ou avec un bon éclairage artificiel.

• Évitez tout démarrage accidentel. Mettez-vous en position de

démarrage chaque fois que vous tirez sur la corde de démarrage.

L'opérateur et l'appareil doivent tous deux être en position stable à

ce moment-là. Voir les Instructions de démarrage et d'arrêt.

• Ne vous étirez pas. Tenez-vous toujours bien sur vos pieds en

position d'équilibre.

• Tenez toujours l'appareil des deux mains lorsque vous le faites

marcher. Agrippez fermement les poignées avant et arrière.

• Gardez les mains, le visage et les pieds éloignés des pièces

mobiles. Ne touchez pas et n'essayez pas d'arrêter l'accessoire de

coupe en rotation.

• Ne touchez pas le moteur, le boîtier d'engrenages ni le silencieux.

Ces pièces deviennent très chaudes à l'utilisation. Elles restent

chaudes brièvement après l'arrêt.

• Servez-vous des outils appropriés. N'utilisez cet outil que pour son

usage prévu.

• Ne faites pas fonctionner le moteur à un régime plus élevé que

nécessaire pour couper, tailler ou faire les bordures. Ne faites pas

tourner le moteur à haut régime si vous ne vous faites pas de coupe.

• Arrêtez toujours le moteur lorsque vous suspendez la coupe ou lorsque

vous vous déplacez d'un lieu de travail vers un autre.

• Si vous heurtez un corps étranger ou que celui-ci est happé, arrêtez le

moteur immédiatement et vérifiez que rien n'a été endommagé. Ne

faites pas fonctionner avant réparation des dommages. Ne faites pas

marcher l'appareil si les pièces sont desserrées ou endommagées.

• Arrêtez et éteignez le moteur dans les cas suivants:

entretien, réparation ou changement d'accessoires ou autres.

• N'utilisez que des pièces de équipement original rechange et

accessoires d’origine du fabricant pour cet appareil. Elles sont

disponibles auprès de votre concessionnaire agréé. L'utilisation de

pièces ou accessoires autres que ceux de éqiupement original peut

causer des blessures graves, endommager l’appareil et annuler sa

garantie.

• Gardez l'appareil exempt d'accumulation de végétation ou autres

matières. Celles-ci peuvent rester logées entre l'accessoire de

coupe et le protecteur.

• Afin de diminuer les risques d'incendie, remplacez tout

silencieux ou pare-étincelles défectueux et conservez le moteur et le

silencieux exempts d'herbe, de feuilles et d'accumulation excessive

de graisse ou de carbone.

AUTRES AVERTISSEMENTS DE SÉCURITÉ

• N'entreposez jamais l'appareil rempli de carburant dans un édifice

où les vapeurs peuvent atteindre une source de flammes vives ou

d'étincelles.

• Laissez le moteur se refroidir avant de l'entreposer ou de le

transporter. Attachez bien l'appareil pendant le transport.

• Rangez l'appareil dans un endroit verrouillé et sec, ou élevé et sec,

hors de portée des enfants, pour éviter une utilisation indésirable ou

un accident.

• Ne trempez et n'arrosez jamais l'appareil avec de l'eau ou tout autre

liquide. Gardez les poignées sèches, propres et exemptes de débris.

Nettoyez après chaque usage. Voir les sections Nettoyage et

Entreposage.

• Conservez ces instructions. Consultez-les souvent et

servez-vous en pour instruire d'autres usagers. Si vous prêtez

l'appareil à quelqu'un, prêtez-lui également ces instructions.

CONSERVER CES INSTRUCTIONS

CONSIGNES DE SÉCURITÉ

AVERTISSEMENT: l'essence est extrêmement

inflammable et ses vapeurs peuvent exploser si on y

met le feu. Veuillez prendre les précautions suivantes.

La page charge ...

Yard Machines Y26SS Manuel utilisateur

Marque: Yard Machines

Modèle: Y26SS

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Yard Machines Y26SS User manual
español: Yard Machines Y26SS Manual de usuario

Yard Machines Y26SS Manuel utilisateur

Yard Machines Y26SS Manuel utilisateur

dans d''autres langues

Autres documents