Simplicity EU CANADIANA SNOWTHROWER Manuel utilisateur

Walkbehind Snowthrower

11.5 TP, 27 Inch (68,6 cm)

1738483

Revision B

08/2009

Model No. 1695696

en

Operator’s Manual

cs

Bedienungsanleitung

de

Käyttäjän käsikirja

fi

Manuale dell’Operatore

fr

Brukerhåndbok

hu Használati útmutató

it

Návod k obsluze lt

Instrukcja obsługi

no

pl

Manuel d’utilisation

sl Uporabniški priročnik

sv

Instruktionsbok

Vartotojo vadovas

Not for

Reproduction

2

Not for

Reproduction

B

2

3

A B

C

5

A

C

B

6

E

A

B

D

C

3

1See Page 15.

4

A

Not for

Reproduction

4

12

Free-HandTM Control

7

A

12

8

A

D

C

B

D

B

9

B

A

B

A D

C

13

A

See Pages 17 and 18.

10 11

Not for

Reproduction

5

A

14

15

B

FULL

16

A

17

18

A

B

C

19

20

21

A

B

A

B

Not for

Reproduction

22

A

23

C

A

B

24

C

A

25

Full

26 A

A

B

C

27

A

28

29

A

B

C

B

E

D

A

C

B C

6

Not for

Reproduction

1/2” (12.5mm)

Deflection

83

7

.030 in.

(.76 mm)

30

31

B

A

32

A

B

33

A

34

35

1/8” (3mm)

Screw

A B

C

A

37

A

B

C

1/32”

(0.8mm)

36 D

E

A

C

B

F

Not for

Reproduction

8

38

A

C

B

“A”

39

40

D

A

41

42

A

C

B

Not for

Reproduction

9

CONTENTS

Illustrations ...........................................................................................3

Operator Safety......................................................................................10

Assembly.............................................................................................16

Features and Controls..............................................................................17

Operation.............................................................................................19

Maintenance.........................................................................................23

Storage ...............................................................................................28

Troubleshooting .....................................................................................29

Specifications .......................................................................................31

General Information

Thank you for purchasing this quality-built Murray snowthrower. We’re pleased that you’ve placed your confidence in the Murray brand.

When operated and maintained according to the instructions in this manual, your Murray product will provide many years of

dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with snowthrowers and how to avoid

them. This snowthrower is designed and intended only for snow throwing and is not intended for any other purpose. It is important that

you read and understand these instructions throughly before attempting to start or operate this equipment. This snowthrower requires

final assembly before use. Refer to the Assembly section for instructions on final assembly procedures. Follow the instructions

completely. Save these instructions for future reference.

Record your model name/number, manufacturer’s identification

numbers, and engine serial numbers in the space provided for

easy access. These numbers can be found in the locations

shown.

When contacting your authorized dealer for replacement

parts, service, or information you MUST have these numbers.

A. Manufacturer’s Identification Number

B. Manufacturer’s Serial Number

C. Power Rating in Kilowatts

D. Maximum Engine Speed in Rotations per Minute

E. Manufacturer’s Name and Address

F. Year of Manufacture

G. CE Compliance Logo

H. Mass of Unit in Kilograms

I. Guaranteed Sound Power in Decibels

Part No. xxxxxxx

xxxxxxxxxxxxxxx

Serial No. xxxxxxxxxx

20xx

kW: x.xx

xxxx max

xxxxxxxxxxxxxxxxxxxxxxx

xxx dB

kg: xxx

A

B

C

D

E

FG

H

I

PRODUCT REFERENCE DATA

Model Description Name/Number

Unit MFG Number Unit SERIAL Number

Mower Deck MFG Number Mower Deck SERIAL Number

Dealer Name Date Purchased

ENGINE REFERENCE DATA

Engine Make Engine Model

Engine Type/Spec Engine Code/Serial Number

CE Identification Tag

Product Reference Data

The Illustrated Parts List for this machine can be downloaded from www.murray.com. Please provide model and serial number when

ordering replacement parts.

Murray is a trademark of Briggs & Stratton Power Products

Group, LLC Milwaukee, WI USA.

Not for

Reproduction

10

OPERATOR SAFETY

The safety alert symbol and signal word (DANGER,

WARNING, CAUTION, or NOTICE) is used to indicate the likeli-

hood and potential severity of personal injury and/or damage to

the product. In addition, a hazard symbol may be used to

represent the type of hazard.

Safety Alert Symbol and Signal Words

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE indicates a situation that could result in damage

to the

product

.

DANGER - Amputation Hazard

The discharge chute contains a rotating

impeller to throw snow. Never clear or unclog

the discharge chute with your hands. Fingers

can quickly become caught and traumatic

amputation or severe laceration will result.

Always use a clean-out tool to clear or unclog

the discharge chute.

Safety Alert – Identifies safety information about

hazards that can result in personal injury.

Operator’s Manual – Read and understand before

performing any activity or running snowthrower.

Rotating Impeller Keep a Safe

Distance from

Snowthrower

Rotating Auger Rotating Gears

Never Reach into

Rotating Parts Thrown Objects

Fire Explosion

Shock Toxic Fumes

Hot Surface Recommended

Ear Protection for

Extended Use

Shut off engine and remove spark plug connector

before performing maintenance or repair work.

Hazard Symbols and Meanings

DANGER

• Hand contact with the rotating impeller inside the discharge

chute is the most common cause of injury associated with

snowthrowers.

• This snowthrower is capable of amputating hands and feet,

and throwing objects. Read and observe all the safety

instructions in this manual. Failure to do so will result in

death or serious injury.

WARNING

U.S.A. Models: Certain components in this product and its

related accessories contain chemicals known to the state of

of California to cause cancer, birth defects, or other repro-

ductive harm. Wash hands after handling.

WARNING

U.S.A. Models: The engine exhaust from this product con-

tains chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

WARNING

U.S.A. Models: Battery posts, terminals, and related acces-

sories contain lead and lead components - chemicals known

to the State of California to cause cancer and reproductive

harm. Wash hands after handling.

Certification: This equipment meets the requirements of ANSI

B71.3-2005 for snowthrowers.

www.murray.com

Not for

Reproduction

OPERATOR SAFETY

Oil

Fuel Forward

On Off Neutral

Choke Off Reverse

Choke On

Stop Electric Start -

Engage (Down) &

Disengage (Up)

Slow Engine - Run

Fast STOP Engine - Stop

Traction Control -

Engage (Down) Auger Control -

Engage (Down)

Auger Clutch Chute Deflector

(Up and Down)

Discharge Chute

(Left and Right) Heated Hand Grips

(High and Low)

Control Symbols on Equipment

12

F

Free-HandTM Control

Easy-TurnTM Traction Control

• Be thoroughly familiar with the controls and the proper use of the snow

thrower.

• Make sure you are properly trained before operating the snowthrower.

•Know how to stop the unit and disengage the controls quickly.

• Never allow anyone to operate the snowthrower without proper instruction.

• Always follow the instructions in the operator’s manual, if the snowthrower

will be stored for an extende d period.

• Maintain or replace safety and instruction labels as necessary.

• Never attempt to make major repairs on the snowthrower unless you have

been properly trained. Improper servicing of the snowthrower can result

in hazardous operation, equipment damage, and voiding of the product

warranty.

DANGER

Read, understand, and follow all the instructions on the

snowthrower and in the operator’s manual before operating

this unit.

Failure to observe the safet y instructions in this manual will

result in death or serious injury.

Read the Manual

TO SAFELY CLEAR A CLOGGED DISCHARGE CHUTE

DANGER: Hand contact with the rotating impeller inside the discharge

chute is the most common cause of injury associated with snow

throwers. Never use your hands to clean out the discharge chute.

FOLLOW THESE INSTRUCTIONS:

1. Shut OFF the engine.

2. Wait 10 seconds to be sure the impeller blades have stopped rotating.

3. Always use a clean-out tool, not your hands.

DANGER

Discharge chute contains rotating impeller to throw snow.

Never clear or unclog the discharge chute with your hands.

Fingers can quickly become caught in the impeller. Always

use a clean-out tool.

Failure to observe these safety instructions will result in

traumatic amputation or severe laceration.

Discharge Chute

NOTE: Not all control symbols shown on this page will appear

on your snowthrower. See FEATURES AND CONTROLS section

for the applicable symbols.

11

Not for

Reproduction

WHEN ADDING FUEL

• Turn off engine and let cool at least 2 minutes before removing the fuel

cap and adding fuel.

• Fill fuel tank outdoors or in a well ventilated area.

• Do not overfill the fuel tank. To allow for the expansion of gasoline, do not fill

above the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other

ignition sources.

• Check fuel lines, cap, and fittings frequently for cracks or leaks. Replace if

necessary.

• Use an approved fuel container.

• If fuel spills, wait until it evaporates before starting engine.

WHEN STARTING ENGINE

• Ensure that spark plug, muffler, fuel cap, and air cleaner (if equipped) are in

place and secured.

• Do not crank the engine with the spark plug removed.

• If fuel is spilled, do not attempt to start the engine, but move the snow

thrower away from the area of the spill, and avoid creating any source of

ignition, until the fuel vapors have dissipated.

• Do not over-prime the engine. Follow the engine starting instructions in this

manual.

• If the engine floods, set choke (if equipped) to OPEN/RUN position, move

throttle (if equipped) to FAST position and crank until engine starts.

WHEN OPERATING EQUIPMENT

• Do not tip the snowthrower at an angle which causes the fuel to spill.

• Do not choke the carburetor to stop the engine.

• Never run the engine with the air cleaner assembly (if equipped) or the air

filter (if equipped) removed.

WHEN CHANGING OIL

• If you drain the oil from the top oil fill tube, the fuel tank must be empty or

fuel can leak out and result in a fire or explosion.

WHEN TRANSPORTING EQUIPMENT

• Transport with fuel tank EMPTY, or with fuel shut-off valve OFF.

WHEN STORING GASOLINE OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, or other appliances that have

pilot light or other ignition source because they can ignite fuel vapors.

DANGER

Fuel and its vapors are extremely flammable and explosive.

Always handle fuel with extreme care.

Failure to observe these safety instructions can cause a fire

or explosion which will result in severe burns or death.

Fuel Handling

• Keep the area of operation clear of all persons, particularly small children

and pets.

• Thoroughly inspect the area where the snowthrower will be used and remove

all doormats, sleds, boards, wires, and other foreign objects.

• Do not operate the snowthrower without wearing adequate winter clothing.

• Wear footwear that will improve footing on slippery surfaces.

• Use caution to avoid slipping or falling especially when operating the

snowthrower in reverse.

• Never operate the snowthrower without good visibility or light. Always be

sure of your footing, and keep a firm hold on the handles.

• Do not clear snow across the face of slopes. Use extreme caution when

changing direction on slopes. Do not attempt to clear steep slopes.

• Do not overload the machine capacity by attempting to clear snow too

quickly.

• Never operate the snowthrower at high transport speeds on slippery

surfaces. Look behind the snowthrower and use care when operating in

reverse.

• Do not use the snowthrower on surfaces above ground level such as roofs of

residences, garages, porches, or other such structures or buildings.

• Operators should evaluate their ability to operate the snowthrower safely

enough to protect themselves and others from injury.

• The snowthrower is intended to remove snow only. Do not use the snow

thrower for any other purpose.

• Do not carry passengers.

• After striking a foreign object, shut OFF the engine, disconnect the cord on

electric motors, thoroughly inspect the snowthrower for any damage, and

repair the damage before restarting and operating the snowthrower.

• If the snowthrower vibrates abnormally, shut OFF the engine. Vibration is

generally a warning of trouble. See an authorized dealer if necessary for

repairs.

• For models equipped with electric starting motors, disconnect the power

cord after the engine starts.

DANGER

This snowthrower is only as safe as the operator. If it is

misused, or not properly maintained, it can be dangerous.

Remember you are responsible for your safety and that of

those around you.

Operation and Equipment Safety

OPERATOR SAFETY

12 www.murray.com

Not for

Reproduction

• Keep children out of the area during operation. Children are often attracted to

the equipment. Be mindful of all persons present.

• Be alert and turn unit off if children enter the area.

• Never allow children to operate the unit.

• Use extra care when approaching blind corners, shrubs, trees, or other

objects that may obscure vision. Children may be present.

DANGER

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the unit

and the operating activity. Never assume that children will

remain where you last saw them.

Children

• Start and run engine outdoors.

• Do not run the engine in an enclosed area, even if doors or windows are

open.

DANGER

Engines give off carbon monoxide, an odorless, colorless,

poison gas.

Breathing carbon monoxide can cause nausea, fainting,

or death.

Engine Safety

• Disengage all clutches and shift into neutral before starting the engine.

• Let the engine adjust to outdoor temperatures before starting to clear snow.

• Use a grounded three-wire plug-in for all snowthrowers equipped with

electric drive motors or electric starting motors.

DANGER

Safe operation of the snowthrower requires the proper care

and maintenance of the engine. Failure to observe the safety

instructions in this manual will result in death or serious

injury.

• Always wear safety glasses or eye shields while during operation, and while

performing an adjustment or repair.

• Always be aware of the direction the snow is being thrown. Nearby

pedestrians, pets, or property may be harmed by objects being thrown.

• Be aware of your environment while operating the snowthrower. Running

over items such as, gravel, doormats, newspapers, toys, and rocks hidden

under snow, can all be thrown from the chute or jam in the auger.

• Use extreme caution when operating on or crossing gravel drives, walks, or

roads.

• Adjust the collector housing height to clear gravel or crushed rock surface.

• Never operate the snowthrower near glass enclosures, automobiles, window

wells, drop-offs, and the like without proper adjustment of the discharge

chute angle.

• Familiarize yourself with the area in which you plan to operate the snow

thrower. Mark off boundaries of walkways and driveways.

DANGER

Objects can be picked up by auger and thrown from chute.

Never discharge snow toward bystanders or allow anyone in

front of the snowthrower. Failure to observe these safety

instructions will result in death or serious injury.

Thrown Objects

• Whenever cleaning, repairing, or inspecting the snowthrower, make sure the

engine is OFF, spark plug wire is disconnected, and all moving parts have

stopped.

• Do not put hands or feet near or under rotating parts. Keep clear of the

discharge opening at all times.

• Never operate the snowthrower without proper guards, and other safety

devices in place and working.

• Never leave the snowthrower unattended while engine is running. Always

disengage the auger and traction controls, stop engine, and remove keys.

• Keep all loose clothing away from the front of the snowthrower and auger.

Scarves, mittens, dangling drawstrings, loose clothes, and pants can quickly

become caught in the rotating device and amputation will occur. Tie up

long hair and remove jewelry.

• Run the machine a few minutes after discharging snow to prevent freeze-up

of the collector/impeller.

• Disengage power to the collector/impeller when snowthrower is transported

or not in use.

DANGER

Keep hands, feet, and clothing away from rotating parts.

Rotating parts can contact or entangle hands, feet, hair,

clothing, or accessories.

Failure to observe these safety instructions will result in

traumatic amputation or severe laceration.

Moving Parts

OPERATOR SAFETY

13

Not for

Reproduction

• When performing any maintenance or repairs on the snowthrower, shut OFF

the engine, disconnect spark plug wire, and keep the wire away from the

plug to prevent someone from accidently starting the engine.

• Check shear bolts and other hardware at frequent intervals for proper

tightness to be sure the snowthrower is in safe working condition.

• Keep nuts and bolts tight and keep snowthrower in good condition.

• Never tamper with safety devices. Check their proper operation regularly and

make necessary repairs if they are not functioning properly.

• Components are subject to wear, damage, and deterioration. Frequently

check components and replace with recommended parts, when necessary.

• Check control operation frequently. Adjust and service as required.

• Use only factory authorized replacement parts when making repairs.

• Always comply with factory specifications on all settings and adjustments.

• Only authorized service locations should be utilized for major service and

repair requirements.

• Use only attachments and accessories approved by the factory (such as

wheel weights, counterweights, or cabs).

• Never attempt to make any adjustments while the engine is running (except

when specifically recommended by the factory).

• Do not allow grease or oil to contact the rubber friction wheel or the disc

drive plate. If the disc drive plate or friction wheel come in contact with

grease or oil, damage to the rubber friction wheel will result.

WARNING

This snowthrower must be properly maintained to ensure safe

operation and performance. Failure to observe the safety

instructions in this manual could result in death or serious

injury.

Maintenance and Storage

-

• If there is natural or LP gas leakage in area, do not start engine.

• Do not use pressurized starting fluids because vapors are flammable.

WARNING

Starting engine creates sparking.

Sparking can ignite nearby flammable gases.

Explosion and fire could result.

• Never touch a hot engine or muffler. Allow muffler, engine cylinder, and fins

to cool before touching.

• Remove debris from muffler area and cylinder area.

• Install and maintain in working order a spark arrester before using equipment

on forest-covered, grass-covered, or brush-covered unimproved land.

•U

U.S.A. Models:

It is a violation of California Public Resource Code

Section 4442 to use or operate the engine on or near any forest-covered,

brush-covered, or grass-covered land unless the exhaust system is equipped

with a spark arrester meeting any applicable local or state laws. Other states

or federal areas may have similar laws.

WARNING

Running the engine produces heat. Engine parts, especially

muffler, become extremely hot.

Failure to observe these safety instructions could result in

severe thermal burns on contact.

Engine Safety (Continued)

OPERATOR SAFETY

14 www.murray.com

DANGER: READ OPERATOR’S

MANUAL.

Read the Operator’s Manual for

operating and safety instructions.

DANGER: THROWN OBJECTS

HAZARD.

Never direct discharge chute

towards persons or property. Keep

bystanders away.

DANGER: REMOVE KEY BEFORE

SERVICING.

Shut off engine and remove key

before performing maintenance or

repair work.

DANGER: AMPUTATION HAZARD.

Contact with auger will cause

serious injury. Keep hands, feet, and

clothing away. Keep bystanders

away.

DANGER: AMPUTATION HAZARD.

Contact with moving parts inside

chute will cause serious injury. Shut

off engine before unclogging

discharge chute. Use clean-out tool,

not hands!

SAFETY ICONS

Not for

Reproduction

15

Safety Decals Figure 1

Look for this symbol to indicate important safety

precautions. This symbol indicates: “Attention!

Become Alert! Your Safety Is At Risk.”

Part No. 1727207

Chute Control Icons

Part No. 1738349

Shift Decal

Part No. 1737867

Auger Control Icons

Product ID Number &

Serial Number Decal

(Rear of Motor Box)

Engine Decals

Part No. 1738348

Chute Rotation

Crank Decal

WARNING: If any safety decals become worn or

damaged and cannot be read, order replacement decals

from your local dealer.

THIS ENGINE MEETS 2008 CA EXH AND EPA

PHASE 2 EMISSION REGULATIONS FOR SMALL

OFF-ROAD ENGINES. REFER TO OWNER'S

MANUAL FOR MAINTENANCE SPECIFICATIONS,

ADJUSTMENTS, AND EMISSIONS

DURABILITY INFORMATION.

EPA EMISSIONS COMPLIANCE PERIOD: CATEGORY: X

CA COMPLIANCE PERIOD: X

DISP: XXXcc e11*97/68SA*XXXX/XX*XXXX*XX

FAMILY XXXXX.XXXXXX XXXXXX

IMPORTANT ENGINE INFORMATION

BRIGGS & STRATTON CORPORATION

Part No. 278297

Part No. 277953

Part No. 1737869

Auger Control Decal

Part No. 1737870

Traction Control Decal

OPERATOR SAFETY

Before operating your snow thrower, read the safety decals as

shown on your snow thrower. The cautions and warnings are

for your safety. To avoid a personal injury or damage to your

snow thrower, understand and follow all the safety decals.

12

Part No. 1738344

Free-HandTM Control Decal

Not for

Reproduction

16

CHECK THE TIRES

Check tires for damage. Check the air pressure in the tires with an

accurate gauge. See the sidewall of the tire for the proper inflation.

CAUTION: Avoid Injury! Explosive separation of tire

and rim parts is possible when they are serviced

incorrectly.

• Do not attempt to mount a tire without the proper

equipment and experience to perform the job.

• Do not inflate the tires above the recommended

pressure.

• Do not weld or heat a wheel and tire assembly. Heat can

cause an increase in air pressure resulting in an

explosion. Welding can structurally weaken or deform

the wheel.

• Do not stand in front or over the tire assembly when

inflating. Use appropriate tool that allows you to stand

to one side.

NOTICE: Check side of tire for maximum tire pressure. DO

NOT exceed maximum.

INSTALL THE DRIFT CUTTER

Drift cutters are used to cut a path through snow deeper than the auger

housing.

1. Loosen the wing nuts (A

A

, Figure 9) that secures the drift cutters (B

B

) to

the auger housing.

2. Raise the drift cutters to the desired height.

3. Tighten the wing nuts.

ASSEMBLY

TOOLS REQUIRED FOR ASSEMBLY

1 – Knife

2 – 1/2" Wrenches (or adjustable wrenches)

1 – 7/16” Wrenches (or adjustable wrenches)

1 – Wrench (or adjustable wrench)

1 – Pair pliers or screw driver (to spread cotter pin)

1 – Hammer

1 – Pry Bar

CHECK CABLE CONNECTION AND ADJUSTMENT

The traction control cable (A

A

, Figure 7) and auger control cable (B

B

) are

adjusted at the factory and no adjustment should be necessary.

If the cables become stretched, unattached or begin to sag, adjustment

will be necessary. See MAINTENANCE section of this manual.

INSTALL THE SPEED CONTROL ROD

Attach the ball joint (A

A

, Figure 6), located on the bottom end of the speed

control rod (B

B

), to the shift yoke assembly (C

C

) with 5/16" lock washer (D

D

)

and 5/16" nut (E

E

).

INSTALL THE CHUTE ROTATION CRANK

1. Insert chute rotator crank rod (A

A

, Figure 5) through hole in dash and

subdash.

2. Align small holes before inserting end of rod into universal bushing

(B

B

).

3. Push straight side of hair pin (C

C

) through both small holes until it

clicks into place.

INSTALL THE DISCHARGE CHUTE

1. Place discharge chute (A

A

, Figure 8) over tabs on chute ring (B

B

) as

shown.

2. Secure discharge chute with three carriage bolts (C

C

) and nuts (D

D

).

3. Tighten hardware to 66 in-lbs (7.6 Nm).

NOTE: Check all bolts and nuts in flange for tightness. Do not

over-tighten.

NOTE: If the chute rotation is slow or binding, loosen the

chute rotation screw 1/4 turn.

WARNING: Always wear safety glasses or eye shields

when assembling the snow thrower.

UNPACK THE SNOW THROWER

1. Using knife, cut along the dotted lines around the top of the carton.

Then remove top of carton as shown in Figure 2.

2. Using knife, cut along the dotted lines around the bottom of the

carton.

3. Push snow thrower off the bottom of the carton to proceed with

assembly.

PARTS BAG CONTENTS

1 – Shear Bolt Kit, 1/4-20 x 1-3/4 in.

1 – Bag of Shear Bolts

1 – Screw, 1/4-20 x 1-3/4 in.

1 – Spacer, Sleeve, 1/4 in.

1 – Hex Locknut, 1/4-20

1 – Fresh Start™ Cartridge

NOTE: “Right” and “Left” are from the Operating Position.

ASSEMBLE THE HANDLES

1. Raise the upper handle (A

A

, Figure 3) to the operating position.

2. Guide speed control rod over wheel.

3. Remove blue shipping tape from cables and cut orange zip ties that

secure control cables to handle assembly and chute rotation parts.

NOTE: Make sure the “Z bend ends of the control lever cables

are secured in the holes on the control levers (A, Figure 4).

Be careful not to cut or damage the control cables. Make sure

the cables are not caught between the upper and lower

handle.

4. Slide two carriage bolts (B

B

, Figure 3) into lower holes and fasten with

two 5/16" lock nuts (C

C

). Tighten all four carriage bolts and nuts with a

1/2" wrench or deep socket.

www.murray.com

Not for

Reproduction

17

FEATURES AND CONTROLS

SNOW THROWER CONTROLS

A. Speed Select Lever — Allows the operator to use one of six (6)

forward and two (2) reverse speeds (see Figure 10). To shift, move

speed select lever to desired position.

NOTICE: Do not move speed select lever while Traction

Drive Clutch is engaged. This may result in severe damage

to drive system.

B. Auger Control Lever — Used to engage and disengage the auger

and impeller. To engage push down, to disengage release.

C. Chute Rotation Crank — Used to rotate the discharge chute to the

left or right.

D. Chute Deflector Wing Nut — Used to control the angle of the

chute deflector (up or down).

E. Free-HandTM Control — After engaging the traction control (left

hand) and auger control (right hand), allows the operator to release

the auger control lever to use the other controls.

F. Traction Control Lever — Used to propel snow thrower forward or

reverse. Push down to engage, release to disengage.

G. Skid Shoe — Used to adjust ground clearance of auger housing.

H. Clean-Out Tool — Used to remove snow and debris from the

discharge chute and the auger housing.

I. Headlight — Used to operate the snow thrower in poor lighting

conditions.

Snow Thrower Controls Figure 10

SNOW THROWER AND ENGINE CONTROLS

B

A

CF

12

E

G

H

D

I

Not for

Reproduction

www.murray.com18

FEATURES AND CONTROLS

ENGINE CONTROLS

A. Choke Control Knob — Used to start a cold engine (see

Figure 11).

B. Electric Start Button — Used to start the engine using the electric

starter.

C. Primer Button — Used to inject fuel directly into the carburetor

manifold to ensure fast starts in cool weather.

D. Safety Key — Must be inserted to start engine. Pull out to stop. Do

not turn safety key.

E. Starter Cord Handle — Used to start the engine manually.

F. ON/OFF Switch — Used to start and stop the engine.

G. Fuel Tank and Cap — Fill the fuel tank to approximately 1-1/2 in.

(38 mm) below the top of the neck to allow for fuel expansion.

H. Oil Fill Cap (Extended Dipstick)

Engine Controls Figure 11

C

H

A

F

E

B

G

STOP

D

Not for

Reproduction

OPERATION

BEFORE OPERATING SNOW THROWER

■

Check the fasteners. Make sure all fasteners are tight.

■

Read this OPERATOR’S MANUAL and OPERATOR SAFETY before

operating your snow thrower. Compare the illustrations with

your SNOW THROWER to familiarize yourself with the location of

various controls and adjustments. Save this manual for future

reference.

NOTE: This snow thrower was shipped WITH OIL in the engine.

See “Before Starting Engine” instructions in the OPERATION

section of this manual before starting engine.

WARNING: The operation of any snow thrower can result in foreign objects being thrown into the eyes, which can result

in severe eye damage. Always wear safety glasses or eye shields before beginning snow thrower operation. We

recommend standard safety glasses or Wide Vision Safety Mask over spectacles.

STOP THE SNOW THROWER

1. Release the auger control lever (B

B,

Figure 12).

2. Release the traction control lever (C

C

).

3. Push the ON/OFF switch (A

A

, Figure 21) to the OFF position and pull

out the safety key (B

B

).

WARNING: Never run engine indoors or in an enclosed,

poor ventilated area. Engine exhaust contains CARBON

MONOXIDE, an ODORLESS and DEADLY GAS.

• Keep hands, feet, hair, and loose clothing away

from any moving parts on engine and snow

thrower.

• Temperature of muffler and nearby areas can

exceed 150°F (66°C). Avoid these areas.

• DO NOT allow children or young teenagers to

operate or be near snow thrower while it is

operating.

OPERATE THE SNOW THROWER

CAUTION: Operation with a Snow Cab. Wind may blow

exhaust gasses back towards the operator. If you notice

the smell of exhaust, change direction of operation.

7. Use the speed select lever (D

D

) to select the forward drive speed. Set

the speed select lever to one of the following positions as determined

by snow conditions:

1-2 Wet, Heavy, Slushy, Extra Deep

3 Moderate

4-5 Very Light

6 Transport

NOTE: When clearing wet, heavy, snow, it is recommended

that the ground speed of the unit be reduced, maintained full

throttle and do not attempt to clear the full width of the unit.

8. To stop moving forward, release the traction control lever (C

C

).

9. To move the snow thrower backwards, move the speed select lever

into either first or second reverse position and engage the traction

control lever.

NOTE: Always release the traction control lever before moving

the speed select lever.

4. Fully press and hold the auger control lever (B

B,

Figure 12) to engage

the auger rotation. Releasing the auger control lever will disengage

the auger - unless the Free-Hand™ control is activated.

5. Fully press and hold the traction/Free-Hand™ control lever (C

C

) to

engage the traction drive and begin moving the snow thrower. To

disengage the traction drive, completely release the lever.

6. When BOTH levers are pressed, the Free-Hand™ control is activated.

This allows you to release the auger control lever to use the other

controls. The auger will continue to rotate until the traction/Free-

Hand™ control lever is released.

CAUTION: Before operating, make sure the area in

front of the snow thrower is clear of bystanders or

obstacles.

NOTICE: Do not throw snow toward a building as hidden

objects could be thrown with sufficient force to cause damage.

1. Start the engine. See “To Start Engine” in this section.

2. Turn the chute rotation crank (A

A

, Figure 12) to set the direction (left or

right) of the discharge chute. See “Discharge Chute and Deflector” in

this section.

3. Loosen the wing nut (A

A

, Figure 15) on the side of the discharge chute

to set angle (up or down) the snow is thrown. See “Discharge Chute

and Deflector” in this section.

19

Not for

Reproduction

OPERATION

WARNING: Read Operator’s Manual before operating

machine. This machine can be dangerous if used

carelessly.

• Never operate the snow thrower without all

guards, covers, shields in place.

• Never direct discharge towards windows or allow

bystanders near machine while engine is

running.

• Stop the engine whenever leaving the operating

position.

• Disconnect spark plug before unclogging the

impeller housing or the discharge chute and

before making repairs or adjustments.

• When leaving the machine, remove the safety key.

To reduce the risk of fire, keep the machine clean

and free from spilled gas, oil, and debris.

TRACTION LOCK PINS

The right traction wheel can be completely released using the locking pin

(A

A

, Figure 13). This allows the unit to be easily moved with the engine off.

DISCHARGE CHUTE AND DEFLECTOR

Discharge Chute Rotation (Left/Right)

1. Turn the chute rotation crank (A

A

, Figure 14) clockwise to rotate the

chute to the right (see Figure 15).

2. Turn crank counterclockwise to rotate the chute to the left.

3. After the desired position is obtained, release the crank.

Chute Deflector (Up/ Down)

1. Loosen the wing nut (A

A

, Figure 15) on the side of the discharge chute

(B

B

).

2. Raise the deflector to provide a higher stream and greater distance. Or,

lower the deflector to provide a lower stream and less distance.

3. After the desired angle is obtained, tighten the wing nut.

CHECK THE OIL (BEFORE STARTING ENGINE)

NOTE: The engine was shipped from the factory filled with oil.

Check the level of the oil. Add oil as needed.

1. Make sure the unit is level. Use a high quality detergent oil classified

“For Service SF, SH, SJ, SL, or higher”.

2. Remove the oil fill cap/dipstick (A

A

, Figure 16) and wipe with a clean cloth.

3. Insert the oil fill cap/dipstick and turn clockwise to tighten.

4. Remove the oil fill cap/dipstick and check the oil.

NOTE: Do not check the level of the oil while the engine runs.

5. If necessary, add oil until the oil reaches the FULL mark on the oil fill

cap/dipstick. Do not add too much oil.

6. Tighten the oil fill cap/dipstick securely each time you check the oil

level.

NOTE: Synthetic 5W30 motor oil is acceptable for all

temperatures. DO NOT mix oil with gasoline. See Chart for oil

recommendations.

* Below 40°F (4°C) the use of SAE 30 will result in hard starting.

** Above 80°F (27°C) the use of 10W-30 may cause increased oil consumption. Check oil

level more frequently.

www.murray.com20

Not for

Reproduction

La page charge ...

Simplicity EU CANADIANA SNOWTHROWER Manuel utilisateur

Simplicity EU CANADIANA SNOWTHROWER Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents