Netgear EX7300 WiFi Mesh Range Extender Manuel utilisateur
- Catégorie
- Les routeurs
- Taper
- Manuel utilisateur
AC2200 WiFi Mesh Extender
Model EX7300v2
Quick Start
X4
Thank you for purchasing this NETGEAR product.
You can visit www.netgear.com/support to register
your product, get help, access the latest downloads
and user manuals, and join our community. We
recommend that you use only official NETGEAR
support resources.
Si ce produit est vendu au Canada, vous pouvez
accéder à ce document en français canadien à
https://downloadcenter.netgear.com/other/.
(If this product is sold in Canada, you can access this
document in Canadian French at
https://downloadcenter.netgear.com/other/.)
For regulatory compliance information including the
EU Declaration of Conformity, visit
https://www.netgear.com/about/regulatory/.
See the regulatory compliance document before
connecting the power supply.
Support
NETGEAR INTL LTD
Building 3, University Technology Centre
Curraheen Road, Cork, Ireland
NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134, USA
© NETGEAR, Inc., NETGEAR and the
NETGEAR Logo are trademarks of NETGEAR,
Inc. Any non‑NETGEAR trademarks are used
for reference purposes only.
LED Description
Router Link
This LED indicates the WiFi connection
between the extender and the router.
• Solid green. Best connection.
• Solid amber. Good connection.
• Solid red. Poor connection.
• Off. No connection.
Client Link
This LED indicates the WiFi connection
between your computer or mobile device and
the extender:
• Solid green. Best connection.
• Solid amber. Good connection.
• Solid red. Poor connection.
• Off. No connection.
Power
• Blinking green. The extender is booting.
• Solid green. The extender is powered
on.
• Off. The extender is powered off.
WPS
• Blinking green. A WPS connection is
being established.
• Solid green. The extended network is
enabled with WiFi security (either WPA
or WPA2).
• Off. The extended network is enabled
without WiFi security.
LED descriptions
Configure a router with
advanced MAC settings
to work with your extender
If you enabled a WiFi MAC filter, WiFi access control,
or access control list (ACL) on your router, when a WiFi
device connects through the extender to your router,
the MAC address of the WiFi device shown on the
router is translated to another MAC address.
If your router’s MAC filter, WiFi access control, or ACL
is enabled, the WiFi device connects to the extender
but cannot get an IP address from the extender and
cannot access the Internet.
To allow the WiFi device to receive an IP address
from the extender and access the Internet, you must
provide the translated MAC address to the router.
To add a translated MAC address to your router
and reserve an IP address for your extender:
1. Log in to your router and disable the MAC filter,
WiFi access control, or ACL.
For more information about how to disable your
router’s MAC filter, WiFi access control, or ACL,
see your router’s documentation.
2. Power on the extender and connect all of your
WiFi devices to the extender.
3. Make sure that the Router Link LED remains lit.
4. Log in to your extender:
a. Launch a web browser from a computer
or mobile device that is connected to your
extender network.
b. Log in to your extender:
• If you did not enable the One WiFi Name
feature, enter www.mywifiext.net in the
address field of the browser.
• If you enabled the One WiFi Name feature,
enter one of the following URLs:
‑Windows-based computer.
http://mywifiext.local/ or
http://mywifiext/
‑Mac computers and iOS devices.
http://mywifiext.local/
‑Android devices.
http://<extender’s IP address>/ (for
example, http://192.168.1.3/)
A login page displays.
c. Enter your admin user name and password
and click the LOG IN button.
The Status page displays.
5. Select Settings > Connected Devices.
The Connected Devices page displays the
MAC addresses and virtual MAC addresses for
computers and WiFi devices that are connected to
the extender network.
6. On the router, add all of the extender’s virtual
MAC addresses and all of the virtual MAC
addresses of the devices connected to the
extender to your router’s MAC filter table.
Note: To reserve a specific IP address for the
extender, you must specify the first virtual MAC
address that displays for your extender’s 2.4 GHz
or 5 GHz network in your router’s IP reservation
table. (The first virtual MAC address that displays
for your extender’s 2.4 GHz and 5 GHz networks is
the same.)
7. Enable the router’s MAC filter, WiFi access control,
or ACL.
May 2019
LED Description
Client
Arrow
• Blinking. Move the WiFi‑enabled
computer or mobile device closer to the
extender.
• Off. Your computer or moble device is
within range of the extender.
Router
Arrow
• Blinking. Move the extender closer to
the router.
• Off. The extender is within range of your
router.
After the setup, the One WiFi Name feature is enabled, which allows your extender to use
the same WiFi network settings as your router.
If you used the Nighthawk app to connect your extender, the following table lists
examples of what your extended WiFi names might look like:
Dual-band router WiFi names Extended WiFi names
2.4 GHz MyWiFiExample MyWiFiExample
5 GHz MyWiFiExample‑5G MyWiFiExample‑5G
If you used WPS to connect your extender, the extended WiFi network name is based on
the first WiFi network that it connected to—2.4 or 5 GHz. The following table lists examples
of what your extended WiFi name might look like:
Dual-band router WiFi names Extender connects
to this network
Extended WiFi name for
2.4 GHz and 5 GHz
2.4 GHz MyWiFiExample MyWiFiExample MyWiFiExample
5 GHz MyWiFiExample‑5G MyWiFiExample
2.4 GHz MyWiFiExample MyWiFiExample‑5G
5 GHz MyWiFiExample‑5G MyWiFiExample‑5G MyWiFiExample‑5G
Connect your device to the extended networkGetting started
1. For initial setup, place your extender in the same
room as your router.
You can move your extender to a new location
after the setup.
2. Plug the extender into an electrical outlet.
3. Wait for Power LED to light solid green.
4. If the Power LED does not light, press the On/Off
button.
5. Connect your extender to your existing WiFi
network using one of these methods:
• Connect with the Nighthawk app. The
Nighthawk app guides you through the
installation. For more information, see
Connect with the Nighthawk app.
• Connect with WPS. Wi‑Fi Protected Setup
(WPS) lets you join a secure WiFi network
without typing the network name and
password. Your router must support WPS to
use this method. For more information, see
Connect with WPS.
WPS does not support WEP network security
or a hidden WiFi network. If your router WiFi
network uses WEP security or uses a hidden
WiFi network, follow the instructions in
Connect with the Nighthawk app.
Connect with the Nighthawk app
1. Download the Nighthawk app on your mobile
device.
For more information about the Nighthawk app,
visit Nighthawk-app.com.
2. On your mobile device, open the WiFi connection
manager, then locate and connect to the extender
network called NETGEAR_EXT.
3. Launch the Nighthawk app.
4. Follow the prompts to connect your extender to
your router WiFi network.
5. After the setup is complete, move your extender
to a new location.
For more information, see Find a good spot for
your extender.
6. Connect your WiFi‑enabled devices to the
extended network.
For more information, see Connect your device to
the extended network.
1. Press the WPS button on the extender for less
than five seconds.
The WPS LED blinks.
Note: If you press the WPS button for more than
five seconds, the extender turns off.
2. Within two minutes, press the WPS button on your
router.
When the extender connects to the router, the
Router Link LED lights.
If the Router Link LED lights green, the connection
between your router and extender is good. If the
Router Link LED lights amber or red, move the
extender closer to the router and try again.
Note: If your router supports the 5 GHz band and
your extender didn’t connect to that band, repeat
the WPS process.
3. Move your extender to a new location.
For more information, see Find a good spot for
your extender.
4. Connect your WiFi‑enabled devices to the
extended network.
For more information, see Connect your device to
the extended network.
Connect with WPS Find a good spot for your
extender
1. Unplug your extender and move it to a new
location.
We recommend that the new location be about
halfway between your router and the area with a
poor WiFi signal.
The extender must be within the range of your
router WiFi network.
2. Power on your extender.
3. Use the Router Link LED to find a spot
where the extender‑to‑router connection is
optimal.
For more information about the Router Link LED,
see LED descriptions on the other side of this
quick start guide.
-
1
-
2
Netgear EX7300 WiFi Mesh Range Extender Manuel utilisateur
- Catégorie
- Les routeurs
- Taper
- Manuel utilisateur