LG LRGL5823S Le manuel du propriétaire

Catégorie
Cuisinières
Taper
Le manuel du propriétaire

Ce manuel convient également à

DESCRIPTION: OWNER’S MANUAL
Part No. MFL33029631
MODEL DESCRIPTION:
Product: Gas Range
Project: MM Single Refresh
Brand: LG Customer: LGECI
PRINTING SPECIFICATION:
1. Trim Size (mm): 182 (W), 257 (H) 4. Printing Method: Off Set
2. Printing Color: Black 5. Bindery Type: Saddle Stitch
3. 6. Language: English & French
7.
Number of Pages: 128
Paper Type:
- Cover: Revolucion (Wood-Free Paper) 71 gr.
- Content: Revolucion (Wood-Free Paper) 71 gr.
8.
Number of Sheets: 64
NOTES:
1. The part should not contain prohibited substances (Pb, Cd, Hg, Cr+6, PBB, PBDE) and should comply
with standard LG (61)-A-9101.
The specication must be the same according to First Parts Approval (FPA).
Quality must not be modied.
LG Electronics Monterrey, México S.A. de C.V.
PART NUMBER: MFL33029631 DATE: July 9, 2020
ENGLISH FRANÇAIS
www.lg.com
MFL33029631
(REV.00 200709)
LRGL5825* LRGL5823* LRGL5821*
OWNER’S MANUAL
GAS RANGE
Read this owner’s manual thoroughly before operating the appliance
and keep it handy for reference at all times.
Do not store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
- Do not try to light any appliance.
- Do not touch any electrical switch.
- Do not use any phone in your building.
- Immediately call your gas supplier from a neighbor's phone. Follow the
gas supplier's instructions.
- If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service
agency, or the gas supplier.
If the information in this manual is not followed exactly, a fire or
explosion may result causing property damage, personal injury or death.
WARNING
Copyright © 2020 LG Electronics Inc. All Rights Reserved.
Never Operate the Top Surface Cooking Section of this Appliance
Unattended
Failure to follow this warning statement could result in fire, explosion, or
burn hazard that could cause property damage, personal injury, or death.
If a fire should occur, keep away from the appliance and immediately call
your fire department.
DO NOT ATTEMPT TO EXTINGUISH AN OIL/GREASE FIRE WITH WATER.
WARNING
2
TABLE OF CONTENTS
TABLE OF CONTENTS
3
PRODUCT FEATURES
4
IMPORTANT SAFETY
INSTRUCTIONS
12
PRODUCT OVERVIEW
12 Parts
12 Accessories
13
INSTALLATION
13 Before Installing the Range
14 Installing the Range
16 Providing Adequate Gas Supply
17 Connecting the Range to Gas
18 Electrical Connections
18 Sealing the Openings
19 Assembling the Surface Burners
19 Checking Ignition of the Surface Burners
20 Leveling the Range
20 Engaging the Anti-tip Device
21
OPERATION
21 Gas Surface Burners
21 Burner Locations
22 Using the Gas Surface Burners
22 Setting the Flame Size
22 In Case of Power Failure
22 Range-Top Cookware
23 Using a Wok
23 Using Stove-Top Grills
23 Using the Griddle
24 The Oven
25 Control Panel Overview
26 Changing Oven Settings
26 Clock
26 Oven Light
26 Minimum & Maximum Default Settings
27 Timer On/Off
-
Setting the Hour Mode
-
Setting the Convection Auto Conversion
Function (Model LRGL5825* /
LRGL5823*)
-
Adjusting the Oven Thermostat
-
Turning the Preheat Alarm Light On/Off
-
Adjusting the Beeper Volume
-
Selecting Fahrenheit or Celsius
29 Lockout
29 Cook Time (Timed Cook)
30 Start Time (Delayed Timed Cook)
31 InstaView™ (Model LRGL5825*)
31 Removing and Replacing the Oven Racks
32 Recommended Baking and Roasting Guide
32 Bake
32 Convection Mode (Model LRGL5825* /
LRGL5823*)
34 Broil
36 Sabbath Mode
36 Favorite (Model LRGL5825*)
36 Wi-Fi
37 Remote Start
37 Frozen Meal (Model LRGL5825*)
37 Slow Cook (Model LRGL5825*)
37 Warm / Keep Warm
37 Proof (Model LRGL5825*)
38 Air Fry (Model LRGL5825* / LRGL5823*)
41
SMART FUNCTIONS
41 LG ThinQ Application
42 Industry Canada Statement
42 IC Radiation Exposure Statement
43 Smart Diagnosis™ Feature
44
MAINTENANCE
44 Gas Surface Burners
45 Burner Grates
45 Cleaning the Cooktop Surface
45 Oven Air Vents
46 Control Panel
46 Front Manifold Panel and Knobs
46 Cleaning the Exterior
47 Door Care Instructions
47 EasyClean
®
49 Self Clean (Model LRGL5825* / LRGL5823*)
51 Changing the Oven Light
51 Removing and Replacing the Lift-Off Oven
Doors and Drawer
53
TROUBLESHOOTING
53 FAQs
55 Before Calling for Service
57
LIMITED WARRANTY
3
PRODUCT FEATURES
ENGLISH
PRODUCT FEATURES
Multiple Gas Burner Sizes
Choose a burner to fit the size of the cookware.
Cooking multiple items at once is possible by using different burners at the
same time.
Safe and Convenient Gas Range
Provides safety and convenience for cooking.
Self Clean (For Some Models) & EasyClean
®
Useful for easy cleaning.
InstaView™
Two quick knocks on the sleek, mirrored glass panel allow you to see inside
the easy access compartment without opening the door.
4
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Read and follow all instructions when using the range to prevent the risk of fire, electric
shock, personal injury, or damage. This guide does not cover all possible conditions that
may occur. Always contact your service agent or manufacturer about problems that you do
not understand.
Download this owner's manual at: https://www.lg.com/ca_en
This is the safety alert symbol. This symbol alerts you to potential hazards that
can result in property damage and/or serious bodily harm or death.
All safety messages will follow the safety alert symbol and either the word
WARNING or CAUTION. These words mean:
WARNING
-
Indicates a hazardous situation which, if not avoided, could result
in death or serious injury.
CAUTION
-
Indicates a hazardous situation which, if not avoided, could result
in minor or moderate injury.
ANTI-TIP DEVICE
WARNING
ALL RANGES CAN TIP
INJURY TO PERSONS COULD RESULT
INSTALL ANTI-TIP DEVICES PACKED WITH RANGE
SEE INSTALLATION INSTRUCTIONS
A child or adult can tip the range and be killed.
Install the anti-tip device to the structure and/or the range. Verify the anti-tip device
has been properly installed and engaged by following the guide of the Anti tip bracket
template.
Engage the range to the anti-tip device by following the guide of the Anti tip bracket
template. Ensure the anti-tip device is re-engaged when the range is moved by
following the guide of the Anti tip bracket template.
Re-engage the anti-tip device if the range is moved. Do not operate the range without
the anti-tip device in place and engaged.
See installation instructions for details.
Failure to do so can result in death or serious burns to children or adults.
To avoid tipping, do not step or sit on the door. Install the anti-tip bracket packed with this
range.
- The range could be tipped and injury might result from spilled hot liquid, food, or the
range itself.
- If the range is pulled away from the wall for cleaning, service, or any other reason,
ensure that the anti-tip device is properly reengaged when the range is pushed back
against the wall.
Anti-tip bracket
Approximately
0.65" (16.5 mm)
Screw must
enter wood or
concrete
Wall plate
5
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
To reduce the risk of the range tipping over, the range must be secured by properly
installing the anti-tip device.
To check that the anti-tip bracket is properly installed: Remove any items on the cooktop.
Grasp the top rear edge of the range back guard and carefully attempt to tilt it forward.
Verify that the anti-tip device is engaged.
Remove the warming or storage drawers and visually inspect that the rear leveling leg is
fully inserted into the anti-tip bracket.
Refer to the installation section of the manual for proper anti-tip bracket installation.
IMPORTANT SAFETY NOTICE
Gas appliances can cause minor exposure to four potentially harmful substances, namely
benzene, carbon monoxide, formaldehyde and soot, caused primarily by the imperfect
combustion of natural or LP gas. Correctly adjusted burners, indicated by a bluish rather
than a yellow flame, will minimize imperfect combustion. Exposure to these substances can
be minimized by opening windows or using a ventilation fan or hood.
WARNING
Never use your range as a space heater to heat or warm the room. Doing so may result
in carbon monoxide poisoning and overheating of the oven.
Never wear loose fitting or hanging garments while using the appliance. Be careful
when reaching for items placed in cabinets over the range. Flammable materials could
be ignited if brought in contact with flame or hot oven surfaces and may cause severe
burns.
Do not place or use combustible materials such as gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
Do not place flammable materials in the oven or near the cooktop.
Do not allow cooking grease or other flammable materials in or near the range.
Do not use water on grease fires. Never touch a flaming pan. Turn the controls off.
Smother a flaming pan on a surface burner by covering the pan completely with a well-
fitting lid, cookie sheet or flat tray. Use a multi-purpose dry chemical or foam-type fire
extinguisher.
A grease fire can be put out by covering it with baking soda or, if available, by using a
multi-purpose dry chemical or foam-type fire extinguisher.
Flame in the oven or the drawer can be smothered completely by closing the oven door
or drawer and turning the control to off or by using a multi-purpose dry chemical or
foam-type fire extinguisher.
Do not use the oven or the drawer for storage.
Let the burner grates and other surfaces cool before touching them.
Never block the vents (air holes) of the range. They provide the air inlet and outlet
necessary for the range to operate properly with correct combustion. Air openings are
located at the rear of the cooktop, at the top and bottom of the oven door, and at the
bottom of the range.
Never obstruct the flow of combustion and ventilation air by blocking the oven vent
or air intakes. Doing so restricts air to the burner and may result in carbon monoxide
poisoning.
Never cover any slots, holes or passages in the oven bottom or cover an entire rack
with materials such as aluminum foil. Doing so blocks air flow through the oven and
may cause carbon monoxide poisoning. Aluminum foil linings may also trap heat,
causing a fire hazard.
6
IMPORTANT SAFETY INSTRUCTIONS
WARNING
Large scratches or impacts to glass doors can lead to broken or shattered glass.
Stepping, leaning or sitting on the doors or drawers of this range can result in serious
injuries and also cause damage to the range. Do not allow children to climb or play
around the range. The weight of a child on an open door may cause the range to tip,
resulting in serious burns or other injury.
Leak testing of the appliance must be conducted according to the manufacturer’s
instructions.
Gas leaks may occur in the system and result in a serious hazard. Gas leaks may
not be detected by smell alone. Gas suppliers recommend you purchase and install
a UL-approved gas detector. Install and use in accordance with the gas detector
manufacturer’s instructions.
Do not use commercial oven cleaners on the oven finish or around any part of the
oven. They will damage the finish.
To prevent staining or discoloration, clean appliance after each use.
Do not attempt to open or close the door or operate the oven until the door is properly
installed.
Never place fingers between the hinge and front oven frame. Hinge arms are spring
mounted. If accidentally hit, the hinge will slam shut against the oven frame and injure
fingers.
CAUTION
Items of interest to children should not be placed in cabinets above the range or on
the backsplash of the range - children climbing on the range to reach items could be
seriously injured.
Do not leave children alone or unattended where a range is hot or in operation. They
could be seriously burned.
Do not let anyone climb, stand or hang on the oven door, warming drawer or cooktop.
They could damage the range or tip it over, causing severe personal injury.
Wear gloves when cleaning the range to avoid injury or burns.
Do not use the oven for storing food or cookware.
To prevent damage to the oven door, do not attempt to open the door when Lock is
displayed.
Do not stand or place excessive weight on an open door. This could tip the range,
break the door, or injure the user.
Do not use delayed baking for highly perishable foods such as dairy products, pork,
poultry, or seafood.
7
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
INSTALLATION SAFETY PRECAUTIONS
Have the installer show you the location of the range gas shut-off valve and how to shut it
off if necessary.
WARNING
Make sure your range is properly installed and grounded by a qualified installer,
according to the installation instructions. Any adjustment and service should be
performed only by qualified gas range installers or service technicians.
Make sure your range is properly adjusted by a qualified service technician or installer
for the type of gas (natural or LP) that is to be used. The range can be converted for
use with either type of gas. See the installation instructions.
These adjustments must be done by a qualified service technician according to the
manufacturer’s instructions and all codes and requirements of the authority having
jurisdiction. Failure to follow these instructions could result in serious injury or property
damage. The qualified agency performing these adjustments assumes responsibility for
the conversion.
Disconnect the electrical supply before servicing the appliance.
Never use the appliance door as a step stool or seat, as this may result in possible
tipping of the appliance and serious injuries.
This product should not be installed below ventilation type hood systems that direct air
in a downward direction.
Doing so may cause ignition and combustion problems with the gas burners resulting in
personal injury and may affect the cooking performance of the unit.
Plug your range into a 120-volt grounded outlet only. Do not remove the round
grounding prong from the plug. If in doubt about the grounding of the home electrical
system, it is your personal responsibility and obligation to have an ungrounded outlet
replaced with a properly grounded, three-prong outlet in accordance with the National
Electrical Code. Do not use an extension cord with this range.
To prevent fire hazard or electrical shock, do not use an adapter plug, an extension
cord, or remove the grounding prong from the electrical power cord. Failure to follow
this warning can cause serious injury, fire or death.
To prevent poor air circulation, place the range out of the kitchen traffic path and out of
drafty locations.
Do not attempt to repair or replace any part of the range unless it is specifically
mentioned in this manual. All other services should be referred to a qualified technician.
Make sure that all packaging materials are removed from the range before operating it
to prevent fire or smoke damage should the packaging material ignite.
8
IMPORTANT SAFETY INSTRUCTIONS
WARNING
To shut off the gas supply to the range, close the range gas shutoff valve by turning it
clockwise.
Adapter(
1
/
2
"-14 NPT)
1
/
2
" Adapter
Lever open
(in use)
Pressure regulator
Range gas shut-off valve
Remove this label
Gas Flow into Range
Installer: Inform the consumer of the location of the gas shut-off valve.
After using the range for an extended period of time, high floor temperatures may
result. Many floor coverings will not withstand this kind of use.
Never install the range over vinyl tile or linoleum that cannot withstand such type of
use. Never install it directly over interior kitchen carpeting.
SURFACE BURNERS
WARNING
Even if the top burner flame goes out, gas is still flowing to the burner until the knob is
turned to the Off position. If you smell gas, immediately open a window and ventilate
the area for five minutes prior to using the burner. Do not leave the burners on
unattended.
Use proper pan size. Do not use pans that are unstable or that can be easily tipped.
Select cookware with flat bottoms large enough to cover burner grates. To avoid
spillovers, make sure the cookware is large enough to contain the food properly. This
will both save cleaning time and prevent hazardous accumulations of food, since heavy
spattering or spillovers left on the range can ignite. Use pans with handles that can be
easily grasped and remain cool.
9
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
CAUTION
Be sure that all surface controls are set in the Off position prior to supplying gas to the
range.
Never leave the surface burners unattended at high flame settings. Boilovers may
cause smoke and greasy spillovers that may ignite.
Always turn the knobs to the Lite position when igniting the top burners and make sure
the burners have ignited.
Control the top burner flame size so it does not extend beyond the edge of the
cookware. Excessive flame is hazardous.
Only use dry pot holders- moist or damp pot holders on hot surfaces may result in
burns from steam. Do not let pot holders come near open flames when lifting cookware.
Do not use towels or other bulky cloth items. Use a pot holder.
If using glass cookware, make sure the cookware is designed for range-top cooking.
To prevent burns from ignition of flammable materials and spillage, turn cookware
handles toward the side or back of the range without extending them over adjacent
burners.
Never leave any items on the cooktop. The hot air from the vent may ignite flammable
items and will increase pressure in closed containers, which may cause them to burst.
Carefully watch foods being fried at a high flame setting.
Always heat fat slowly, and watch as it heats.
If frying combinations of oils and fats, stir together before heating.
Use a deep fat thermometer if possible to prevent overheating fat from heating beyond
the smoking point.
Use the least possible amount of fat for effective shallow or deep fat frying. Filling the
pan with too much fat can cause spillovers when food is added.
Do not cook foods directly on an open flame on the cooktop.
Do not use a wok on the surface burners if the wok has a round metal ring that is
placed over the burner grate to support the wok. This ring acts as a heat trap, which
may damage the burner grate and burner head. It may also cause the burner to work
improperly. This may cause carbon monoxide levels which are higher than what is
allowed by current standards, resulting in a health hazard.
Foods for frying should be as dry as possible. Frost or moisture on foods can cause hot
fat to bubble up and spill over the sides of the pan.
Never try to move a pan of hot fat, especially a deep fryer. Wait until the fat is cool.
Do not place plastic items on the cooktop- they may melt if left too close to the vent.
Keep all plastics away from the surface burners.
To prevent burns, always be sure that the controls for all burners are in the Off position
and all grates are cool before attempting to remove them.
If you smell gas, turn off the gas to the range and call a qualified service technician.
Never use an open flame to locate a leak.
Always turn the knobs to the Off position before removing cookware.
Do not lift the cooktop. Lifting the cooktop can cause damage and improper operation
of the range.
If the range is located near a window, do not hang long curtains that could blow over
the surface burners and catch on fire.
Use care when cleaning the cooktop. The pointed metal ends on the electrodes could
cause injury.
10
IMPORTANT SAFETY INSTRUCTIONS
BROILER
Always use a broiler pan and a grid for excess fat and grease drainage. This will help to
reduce splatter, smoke, and flare-ups.
WARNING
When using the broiler, the temperature inside the oven will be extremely high. Take
caution to avoid possible burns by:
Keeping the door closed when broiling (refer to Broil section of the manual)
Always wearing oven mitts when inserting or removing food items
COOK MEAT AND POULTRY THOROUGHLY
To protect against food-borne illnesses, cook meat and poultry thoroughly—ground beef to at
least an INTERNAL temperature of 160 °F, poultry to at least an INTERNAL temperature of 165
°F and beef, pork, veal & lamb steaks & chops to at least an INTERNAL temperature of 145 °F.
SELF CLEANING OVEN
Make sure to wipe off excess spillage before operating the self clean function.
CAUTION
Do not leave food, cooking utensils, racks, etc. in the oven during the self clean cycle.
Do not use oven cleaners. No commercial oven cleaner or oven liner protective coating
of any kind should be used in or around any part of the oven. Residue from oven
cleaners will damage the inside of the oven when the self clean cycle is used.
Remove oven racks and other items from the oven before starting the self clean cycle.
Only clean the parts listed in this manual.
Do not clean the door gasket. The door gasket is necessary for a good seal. Care
should be taken not to rub, damage or move the gasket.
If the self cleaning mode malfunctions, turn the range off and disconnect the power
supply. Have the range serviced by a qualified technician.
It is normal for parts of the oven to become hot during a self clean cycle.
Avoid touching the door, window or oven vent area during a clean cycle.
OVEN
When opening the door of a hot oven, stand away from the range. The hot air and steam
that escape can cause burns to hands, face and eyes.
WARNING
Never block any slots, holes or passages in the oven bottom or cover an entire rack
with materials such as aluminum foil. Doing so blocks air flow through the oven and
may cause carbon monoxide poisoning. Aluminum foil linings may trap heat, causing a
fire hazard.
Do not heat food in closed containers. Pressure inside the container could increase and
cause the container to burst, resulting in injury.
11
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
WARNING
Do not line oven walls or bottom with aluminum foil or allow them to contact exposed
heating elements in the oven. Doing so could create a fire hazard or cause damage to
the range.
Do not use the oven for storage. Items stored in the oven can catch on fire.
Keep the oven free from grease buildup.
Insert the oven racks in the desired position while the oven is cool.
To prevent burns when removing food, slide racks out until the stop engages, then
remove food items. This may also protect you from getting burnt by touching hot
surfaces of the door or oven walls.
When placing or removing a griddle, always wear oven mitts.
When using cooking or roasting bags in the oven, follow the manufacturer’s directions.
Use only glass cookware that is recommended for use in gas ovens.
Always remove the broiler pan from the range after you finish broiling. Grease left in the
pan can catch fire if the oven is used without removing the grease from the broiler pan.
If meat is too close to the flame while broiling, the fat may ignite. Trim excess fat to
prevent excessive flare-ups.
Make sure the broiler pan is in place correctly to minimize the possibility of grease fires.
If you have a grease fire in the broiler pan, press the Clear/Off and keep the oven door
closed to contain the fire until it burns out.
For safety and better cooking performance, always bake and broil with the oven door
closed. Open door baking or broiling can cause damage to the knobs or valves.
Do not leave the oven door open during cooking or while the oven is cooling down.
ENERGY SAVING TIPS
Multiple-rack cooking saves time and energy. Whenever possible, cook foods requiring the
same cooking temperature together in one oven.
For optimal performance and energy savings, follow the guides on page 32 for proper rack
and pan placements.
Match the size of the cookware to the amount of food being cooked to save energy when
heating. Heating ½ quart of water requires more energy in a 3-quart pot than in a 1-quart
pot.
Use cookware with flat bottoms to provide the best contact with the cooktop surface when
cooking on the glass-ceramic cooktop.
Match the size of the cooktop burner or element to the size of the cookware in use. Using
a large element for a small pan wastes heating energy, and the exposed surface of the
element is a burn or fire hazard.
Reduce energy use by cleaning light oven soils with the EasyClean
®
feature instead of
self-clean.
Avoid opening the oven door more than necessary during use. This helps the oven
maintain temperature, prevents unnecessary heat loss, and saves on energy use.
Read all instructions before using the appliance.
SAVE THESE INSTRUCTIONS
12
PRODUCT OVERVIEW
PRODUCT OVERVIEW
Parts
Grate
Oven control panel
Cooktop
Automatic oven light switch
Door gasket
Anti-tip bracket
Oven vent
Burner control knob
Rack
Oven door
Storage drawer
Model and serial
number plate
Accessories
Included Accessories
Standard rack
- Model LRGL5825* (3ea)
- Model LRGL5823*/LRGL5821* (2ea)
Griddle (1ea)
- Model LRGL5825*/LRGL5823*
Owner’s manual (1ea)
Anti-tip kit
Anti-tip (1ea) Screws (4ea) Anchors (4ea) Template (1ea)
LP nozzle conversion kit
Optional Accessories
Broiler pan
Grid
Air fry tray
Cooktop Nozzles (5ea) Oven Nozzles (2ea)
NOTE
Contact LG Customer Service at (LG U.S.) 1-800-243-0000 or (LG Canada) 1-888-542-2623, if any
accessories are missing.
For your safety and for extended product life, only use authorized components.
The manufacturer is not responsible for product malfunction or accidents caused by the use of separately
purchased, unauthorized components or parts.
The images in this guide may be different from the actual components and accessories, which are subject
to change by the manufacturer without prior notice for product improvement purposes.
13
INSTALLATION
ENGLISH
INSTALLATION
Before Installing the Range
Make sure the range is properly installed and grounded by a qualified installer, according to the installation
instructions. Any adjustment and service should be performed only by qualified gas range installers or service
technicians.
In the Commonwealth of Massachusetts
This product must be installed by a licensed plumber or gas fitter.
When using ball type gas shut-off valves, they must be the T-handle type.
When using a flexible gas connector, it must not exceed 3 feet in length.
Preparing for Installation
Tools Needed
Phillips screwdriver
Open-end or adjustable
wrench
Pencil and ruler
Level
Flat-blade screwdriver
Pipe wrench (2)
(one for support)
Flat-blade screwdriver
(simmer adjustment)
Diameter: 3/32" (2.4 mm)
L: 3" (76.2 mm)
L
Materials You May Need
Gas line shut-off valve
Pipe joint sealant that resists action of natural and LP gases
Flexible metal appliance connector (
3
/
4
" or
1
/
2
" NPT x
1
/
2
" I.D.)
Never use an old connector when installing a new range.
Flare union adapter for connection to gas supply line (
3
/
4
" or
1
/
2
" NPT x
1
/
2
" I.D.)
Flare union adapter for connection to pressure regulator on range (
1
/
2
" NPT x
1
/
2
" I.D.)
Liquid leak detector or soapy water
Lag bolt or
1
/
2
" O.D. sleeve anchor (for concrete floors only)
14
INSTALLATION
Installing the Range
Unpacking and Moving the Range
CAUTION
You should use two or more people to move
and install the range. (Excessive Weight
Hazard) Failure to do so can result in back or
other injury.
Do not use the door handles to push or
pull the range during installation or when
moving the range out for cleaning or
service. Doing so can result in serious damage
to the door of the range.
Remove packing material, protective film, tape and
any temporary labels from your range before using.
Do not remove any warning-type labels, the model
and serial number label, or the Tech Sheet that is
located on the back of the range.
To remove any remaining tape or glue, rub the area
briskly with your thumb. Tape or glue residue can also
be easily removed by rubbing a small amount of liquid
dish soap over the adhesive with your fingers. Wipe
with warm water and dry.
Do not use sharp instruments, rubbing alcohol,
flammable fluids, or abrasive cleaners to remove tape
or glue. These products can damage the surface of
your range.
Your range is heavy and can be installed on soft
floor coverings such as cushioned vinyl or carpeting.
Use care when moving the range on this type of
flooring. Use a belt when moving the range to prevent
damaging the floor. Or slide the range onto cardboard
or plywood to avoid damaging the floor covering.
Choosing the Proper Location
Do not locate your range where it may be subject to
strong drafts. Any openings in the floor or wall behind
the range should be sealed. Make sure the openings
around the base of the range that supply fresh air
for combustion and ventilation are not blocked by
carpeting or woodwork.
Your range, like many other household units, is heavy
and can be installed on soft floor coverings such as
cushioned vinyl or carpeting. Use care when moving
the range on this type of flooring.
This appliance must not be installed with a ventilation
system that blows air downward toward the range.
This type of ventilation system may cause ignition and
combustion problems with the gas cooking appliance
resulting in personal injury or unintended operation.
When the floor covering ends at the front of the
range, the area that the range will be installed on
should be built up with plywood to the same level
or higher than the floor covering. This will allow the
range to be moved for cleaning and servicing, as well
as provide proper air flow to the range.
Also, make sure the floor covering can resist
temperatures of at least 167 °F (75 °C). See the
Installation Safety Precautions included in this
manual.
Make sure the wall coverings around your range can
resist the heat generated up to 194 °F (90 °C) by
the range. See the Precautions Safety Precautions
included in this manual.
Gas Pipe and Electrical Outlet
Locations
30"
(76.2 cm)
3" (7.6 cm)
7
1
/
2
"
(19 cm)
6
1
/
2
"
(16.5 cm)
23
1
/
2
"
(60 cm)
21
1
/
2
"
(54.5 cm)
2"
(5.1 cm)
3"
(7.6 cm)
11
1
/
2
"
(30 cm)
15
INSTALLATION
ENGLISH
Dimensions and Clearances
Provide proper clearance between the range and adjacent combustible surfaces. These dimensions must be met
for safe use of your range. The location of the electrical outlet and pipe opening (see Gas Pipe and Electrical
Outlet Locations, page 14) may be adjusted to meet specific requirements. The range may be placed with 0"
clearance (flush) at the back wall.
Maximum
depth for
cabinets
above
coutertops
Minimum
clearance
to left wall
Minimum to
cabinets on
either side
of the range
Minimum
clearance
to right wall
Front edge
of the range
side panel
forward from
cabinet
To cabinets
below
cooktop and
at the range
back
Depth with door closed
(includes door handle)
30"
(76.2 cm)
30" (76.2 cm)
Minimum
18"
(45.72 cm)
5"
5" (12.7 cm)
1
/
4
"
(0.6 cm)
28
29
/
32
"
(73.4 cm)
36"
(91.3 cm)
Height
46
1
/
2
"
(118.1 cm)
Depth with door open
47
1
/
4
"
(120.1 cm)
29
7
/
8
"
(75.9 cm)
13" (33 cm)
0"
Dimensions
Installation Clearances
36"
(91.4 cm)
16
INSTALLATION
Installing the Anti-tip Device
Anti-tip
bracket
Wall plate
Screw must
enter wood or
concrete
The anti-tip bracket is packaged with an installation
template. The instructions include necessary
information to complete the installation. Read and
follow the range installation instruction sheet.
WARNING
Range must be secured with an approved
anti-tip device.
The range could be tipped by standing, sitting
or leaning on an open door if the range or
anti-tip device is not properly installed.
After installing the anti-tip device, verify that it is
in place by carefully attempting to tilt the range
forward.
This range has been designed to meet all
recognized industry tip standards for all normal
conditions.
The installation of the anti-tip device must meet
all local codes for securing the appliance.
The use of this device does not preclude tipping
of the range when not properly installed.
A child or adult can tip the range and be killed.
Install the anti-tip device to the structure and/
or the range. Verify the anti-tip device has been
properly installed and engaged by following the
guide of the Anti tip bracket template.
Engage the range to the anti-tip device by
following the guide of the Anti tip bracket
template. Ensure the anti-tip device is re-
engaged when the range is moved by following
the guide of the Anti tip bracket template.
Re-engage the anti-tip device if the range is
moved. Do not operate the range without the
anti-tip device in place and engaged.
See installation instructions for details.
Failure to do so can result in death or serious
burns to children or adults.
Providing Adequate Gas
Supply
The range is designed to operate at a pressure of
5" of water column on natural gas or 10" of water
column on LP.
Make sure you are supplying your range with the type
of gas for which it is configured.
This range is convertible for use on natural or LP gas.
When using this range on LP gas, conversion must
be made by a qualified LP installer before attempting
to operate the range.
For proper operation, the pressure of natural gas
supplied to the regulator must be between 5" and 13"
of water column.
For LP gas, the pressure supplied to the regulator
must be between 10" and 13" of water column. When
checking for correct operation of the regulator, the
inlet pressure must be at least 1" more than the
operating (manifold) pressure as given above.
The pressure regulator located at the inlet of the
range must remain in the supply line regardless of
which type of gas is being used.
A flexible metal appliance connector used to connect
the range to the gas supply line should have an I.D.
of
5
/
8
" and a maximum length of 5 feet. In Canada,
flexible connectors must be single wall metal
connectors less than 6 feet in length.
17
INSTALLATION
ENGLISH
Connecting the Range to Gas
Shut off the range gas supply valve before
removing the old range and leave it off until the
new hook-up has been completed.
Because hard piping restricts movement of the range,
the use of a CSA International-certified flexible metal
appliance connector should be used unless local
codes require a hard-piped connection.
A manual valve shall be installed in an accessible
location in the gas piping external to the appliance
for the purpose of turning on or shutting off gas to the
appliance.
Never reuse an old connector when installing a new
range.
To protect against gas leaks, use a qualified pipe joint
sealant on all external threads.
1
Install a male
1
/
2
" or
3
/
4
" flare union adapter to the
NPT internal thread of the manual shut-off valve,
taking care to back-up the shut-off valve to keep
it from turning.
2
Install a male
1
/
2
" flare union adapter to the
1
/
2
"
NPT internal thread at the inlet of the pressure
regulator. Use a backup wrench on the pressure
regulator fitting to prevent damage.
Check that the gas pressure regulator valve is in the
open position.
Lever’s open
position
Lever’s closed
position
NOTE
The gas pressure regulator valve is open when
shipped. If the range does not work properly
after installation, make sure the regulator valve
is still open.
3
Connect a flexible metal appliance connector to
the adapter on the range. Position the range to
permit connection at the shut-off valve.
4
When all connections have been made, be sure
all range controls are in the OFF position and the
pressure regulator valve is open before turning
on the main gas supply valve. Gas leaks may
occur in your system and create a hazard. Gas
leaks may not be detected by smell alone.
Check all gas connection joints and fittings for
leaks with a non-corrosive leak detection fluid,
then wipe off.
Gas suppliers recommend you purchase and
install a UL approved gas detector. Install and use
in accordance with the installation instructions.
WARNING
Do not use a flame to check for gas leaks.
Isolate the range from the gas supply system
by closing its individual shut-off valve during
any pressure testing of the gas supply system
at test pressures equal to or less than
1
/
2
psi
(3.5 kPa).
The appliance and its individual shut-off valve
must be disconnected from the gas supply
piping system during any pressure testing of
that system at test pressures in excess of
1
/
2
psi
(3.5 kPa).
Flexible Connector Hookup
1
/
2
"
Adapter
1
/
2
" Adapter
1
/
2
"
Adapter
Pressure
regulator
Flex connector
(6 ft. max.)
Gas shut-off valve
1
/
2
" or
3
/
4
" Gas pipe
Gas Flow into Range
Installer: Inform the consumer of the location of the gas
shut-off valve
.
Pressure Regulator Position
Pressure Regulator
18
INSTALLATION
Electrical Connections
Electrical Requirements
120 Volt, 60 Hz, properly grounded dedicated circuit
protected by a 15 or 20 Amp circuit breaker, or slow
blow fuse.
If an external electrical source is utilized, a statement
that the appliance, when installed, must be electrically
grounded in accordance with local codes or, in the
absence of local codes, with the National Electrical
Code, NFPA 70 or the Canadian Electric Code, CSA
C22.1-02.
Grounding
IMPORTANT: FOR PERSONAL SAFETY, THIS
APPLIANCE MUST BE PROPERLY GROUNDED.
The power cord of this appliance is equipped with
a 3-prong (grounding) plug which mates with a
standard 3-prong grounding wall receptacle to
minimize the possibility of electric shock hazard from
this appliance.
The customer should have the wall receptacle and
circuit checked by a qualified electrician to make sure
the receptacle is properly grounded.
Where a standard two-prong wall receptacle is
encountered, it is the personal responsibility and
obligation of the customer to have it replaced with a
properly grounded three-prong wall receptacle.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR
REMOVE THE THIRD (GROUND) PRONG FROM
THE POWER CORD.
A word about GFCI’s – GFCI’s are not required or
recommended for gas range receptacles.
Ground Fault Circuit Interrupters (GFCI’s) are
devices that sense leakage of current in a circuit
and automatically switch off power when a threshold
leakage level is detected. These devices must
be manually reset by the consumer. The National
Electrical Code requires the use of GFCI’s in kitchen
receptacles installed to serve countertop surfaces.
Performance of the range will not be affected if
operated on a GFCI-protected circuit but the occasional
resetting of the circuit can become an annoyance.
Ensure proper ground
exists before use
Preferred
Method
CAUTION
Have the circuit checked by a qualified electrician
to make sure the receptacle is properly grounded.
Do not use an adapter plug. Disconnecting of the
power cord places undue strain on the adapter
and leads to eventual failure of the adapter ground
terminal.
Installation must conform with local codes or, in the
absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1/NFPA 54 or, in Canada, the
Natural Gas and Propane Installation Code, CSA
B149.1.
The installation of appliances designed for mobile
home installation must conform with the Manufactured
Home Construction and Safety Standard, Title 24
CFR, Part 3280 (formerly the Federal Standard
for Mobile Home Construction and Safety, Title
24, HUD, Part 280) or, when such standard is not
applicable, the Standard for Manufactured Home
Installations, latest edition (Manufactured Home Sites,
Communities and Set-Ups), ANSI A225.1, latest
edition, or with local codes. In Canada, mobile home
installation must be in accordance with the current
CAN/CSA Z240/MH Mobile Home Installation Code.
Sealing the Openings
Seal any openings in the wall and floor after electrical
and gas supplies are completed.
19
INSTALLATION
ENGLISH
Assembling the Surface
Burners
CAUTION
Do not operate the burners without all parts in place.
Place the burner caps and heads on the cooktop.
Make sure that the caps and heads are placed in the
correct locations. There is one small, one medium,
one large, and one extra large burner head and cap.
Center Burner
Oval (Center) burner
head/cap assembly
Small burner
head and
cap
Medium
burner
head
and cap
Large burner
head and cap
Front of range
Extra large burner
head and cap
Hole
Hole
Electrode
Electrode
Make sure the hole in the burner head is positioned
over the electrode.
Checking Ignition of the
Surface Burners
Electric Ignition
Select a surface burner knob and simultaneously
push in and turn to the Lite position. You will hear
a clicking sound indicating proper operation of the
spark module.
Once the air has been purged from the supply lines
the burner should ignite within 4 seconds. After the
burner ignites, rotate the knob out of the Lite position.
Try each burner in succession until all burners have
been checked.
Quality of Flames
The combustion quality of the burner flames needs to
be confirmed visually.
A Yellow flames - Call for service.
B Yellow tips on outer cones - This
is normal for LP gas.
C Soft blue flames - This is normal
for natural gas.
NOTE
With LP gas, some yellow tipping on outer
cones is normal.
Adjusting the Surface Burner to the
Low Flame (Simmer) Setting
1
Light all surface burners.
2
Turn the knob on the burner being adjusted to
Lo.
3
Remove the knob.
4
Insert a small, flat-blade screwdriver with a
minimum length of 3" (76.2 mm) and a diameter
of
3
/
32
" (2.4 mm) into the valve shaft.
Valve shaft
Center adjustment screw
NOTE
Hold the valve shaft with one hand while turning
the screw to adjust with the other.
5
Replace the knob.
6
Test the flame stability.
Test 1: Turn the knob from Hi to Lo quickly. If the
flame goes out, increase the flame size and test
again.
Test 2: With the burner on a Lo setting, open
and close the oven door quickly. If the flame is
extinguished by the air currents created by the
door movement, increase the flame height and
test again.
7
Repeat steps 1-6 for each surface burner.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129

LG LRGL5823S Le manuel du propriétaire

Catégorie
Cuisinières
Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues