EGO ME0801 Le manuel du propriétaire

WARNING: To reduce the risk of injury, the user must read and understand the

Operator’s Manual before using this product. Save these instructions for future reference.

Español p. 53

Français p. 26

OPERATOR'S MANUAL

EDGER

ATTACHMENT

MODEL NUMBER EA0800

EXCLUSIVELY FOR USE WITH

EGO POWER+ POWER HEAD PH1400

16-1107_EGO_EA0800_Edger Attachment_manual_NA_V1

EDGER ATTACHMENT—EA08002

TABLE OF CONTENTS

Safety Symbols ..........................................4

Safety Instructions ......................................5-8

Introduction .............................................8

Speciﬁcations ...........................................9

Packing List .............................................9

Description .........................................10-11

Assembly ...........................................12-13

Operation ...........................................14-16

Maintenance ........................................17-22

Troubleshooting .........................................23

Warranty ...........................................24-25

EDGER ATTACHMENT—EA0800 3

READ ALL INSTRUCTIONS!

READ & UNDERSTAND

OPERATOR'S MANUAL

WARNING:

Some dust created by power sanding, sawing, grinding, drilling

and other construction activities contains chemicals known to the state of California

to cause cancer, birth defects or other reproductive harm. Some examples of these

chemicals are:



Lead from lead-based paints



Crystalline silica from bricks and cement and other masonry products, and



Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area, and

work with approved safety equipment, such as those dust masks that are specially

designed to ﬁlter out microscopic particles.

EDGER ATTACHMENT—EA08004

SAFETY SYMBOLS

The purpose of safety symbols is to attract your attention to possible dangers. The

safety symbols and the explanations with them deserve your careful attention and

understanding. The symbol warnings do not, by themselves, eliminate any danger.

The instructions and warnings they give are no substitutes for proper accident

prevention measures.

WARNING:

Be sure to read and understand all safety instructions in this

Operator’s Manual, including all safety alert symbols such as “DANGER,” “WARNING,”

and “CAUTION” before using this tool. Failure to following all instructions listed below

may result in electric shock, ﬁre, and/or serious personal injury.

SYMBOL MEANING

SAFETY ALERT SYMBOL:

Indicates DANGER, WARNING, OR CAUTION.

May be used in conjunction with other symbols or pictographs.

WARNING!

The operation of any power tools can result in foreign

objects being thrown into your eyes, which can result in severe eye

damage. Before beginning power tool operation, always wear safety

goggles or safety glasses with side shield and a full face shield when

needed. We recommend a Wide Vision Safety Mask for use over

eyeglasses or standard safety glasses with side shields. Always use eye protection

which is marked to comply with ANSI Z87.1.

EDGER ATTACHMENT—EA0800 5

SAFETY INSTRUCTIONS

This page depicts and describes safety symbols that may appear on this product. Read,

understand, and follow all instructions on the machine before attempting to assemble

and operate it.

Safety Alert Indicates a potential personal injury hazard.

Read &

Understand

Operator's

Manual

To reduce the risk of injury, user must read and

understand the operator’s manual before using

this product.

Eye Protection

Always wear safety goggles or safety glasses

with side shields and a full face shield when

operating this product.

Recycle Symbols

This product uses lithium-ion (Li-ion) batteries.

Local, state, or federal laws may prohibit disposal

of batteries in ordinary trash. Consult your

local waste authority for information regarding

available recycling and/or disposal options.

IPX4

Ingress Protection

Degree

Protection from splashing water

V Volt Voltage

mm Millimeter Length or size

cm Centimeter Length or size

in. Inch Length or size

kg Kilogram Weight

lb Pound Weight

Direct Current Type or a characteristic of current

EDGER ATTACHMENT—EA08006

IMPORTANT SAFETY INSTRUCTIONS

WARNING!

When using electric gardening appliances, basic safety precautions

should always be followed to reduce the risk of ﬁre, electric shock, and personal injury,

including the following:

READ ALL INSTRUCTIONS

DANGER!

Do not rely on the tool’s insulation against electric shock. To reduce

the risk of electrocution, never operate the tool in the vicinity of any wires or cables

which may carry electric current.

CAUTION!

Wear appropriate personal hearing protection during use. Under some

conditions and durations of use, noise from this product may contribute to hearing loss.



Avoid Dangerous Environment – Don’t use appliances in damp or wet

locations.



Keep Children Away - All visitors should be kept at a distance away from work

area.



Dress Properly - Do not wear loose clothing or jewelry. They can be caught in

moving parts. Use of rubber gloves and substantial footwear is recommended

when working outdoors. Wear protective hair covering to contain long hair.



Use Safety Glasses - Always use face or dust mask if operation is dusty.



Use Right Appliance - Do not use appliance for any job except that for which it

is intended.



Don’t Force Appliance - It will do the job better and with less likelihood of a risk

of injury at the rate for which it was designed.



Don’t Overreach - Keep proper footing and balance at all times.



Stay Alert - Watch what you are doing. Use common sense. Do not operate the

edger when you are tired.



Do not operate the edger while under the inﬂuence of alcohol or drugs.



Keep guards in place and in working order.



Keep blades sharp. Replace dull or worn blade; do not attempt to sharpen.



Keep hands and feet away from the cutting area.



Never stand or have any part of your body in line with the path of the

edger blade.



Store Idle Appliances Indoors - When not in use, appliances should be stored

EDGER ATTACHMENT—EA0800 7

indoors in a dry and high or locked-up place with the battery pack removed- out

of reach of children.



Maintain Appliance with Care - Keep cutting edge sharp and clean for best

performance and to reduce the risk of injury. Follow instructions for lubricating

and changing accessories. Keep handles dry, clean, and free from oil and grease.



Check Damaged Parts - Before further use of the product, a guard or other part

that is damaged should be carefully checked to determine that it will operate

properly and perform its intended function. Check for alignment of moving parts,

binding of moving parts, breakage of parts, mounting, and any other condition

that may affect its operation. A guard or other part that is damaged should be

properly repaired or replaced by an authorized service center unless indicated

elsewhere in this manual.



Clear the area to be cut before each use. Remove all objects such as rocks,

broken glass, nails, wire, or string that can be thrown or become entangled in the

cutting attachment.



Always hold the edger ﬁrmly, with both hands on the handles, while

operating. Wrap your ﬁngers and thumbs around the handles.



Avoid Accidentally Starting - Don’t carry the edger with your ﬁnger on the

trigger.



Do not operate the edger in gaseous or explosive atmospheres. Motors in

these appliances normally spark, and the sparks might ignite fumes.



Do not use the edger on or near graveled surfaces.



Damage to Edger - If you strike a foreign object with the edger, stop the tool

immediately, check for damage and have any damage repaired before further

operation is attempted. Do not operate with a broken guard or blade.



Replace a cracked, damaged or worn-out blade immediately, even if

damage is limited to superﬁcial cracks. Such attachments may shatter at

high speed and cause serious or fatal injury.



Do not charge the battery pack in rain, or in wet locations.



Use only with the battery packs and chargers listed below:

BATTERY PACK CHARGER

BA1120, BA1400, BA2240,

BA2800, BA4200

CH2100

CH5500



Use Only With The 56V Lithium-Ion Power Head PH1400.

EDGER ATTACHMENT—EA08008



Do not dispose of the battery in a ﬁre. The cells may explode. Check with

local codes for possible special disposal instructions.



Do not open or mutilate the battery. Released electrolyte is corrosive and

may cause damage to the eyes or skin. It may be toxic if swallowed.



Exercise care in handling batteries in order not to short the battery with

conducting materials such as rings, bracelets, and keys. The battery or

conductor may overheat and cause burns.



Replacement Parts - When servicing, use only identical EGO replacement parts.

Use of any other accessory or attachment may increase the risk of injury.



Battery tools do not have to be plugged into an electrical outlet;

therefore, they are always in operating condition. Be aware of possible

hazards even when the tool is not operating. Take care when performing

maintenance or service.



Remove or disconnect the battery pack before servicing, cleaning or

removing material from the product.



Do not wash with a hose; avoid getting water in motor and electrical

connections.



If situations occur that are not covered in this manual, use care and

good judgment. Contact the EGO Customer Service Center for assistance.



Save these instructions. Refer to them frequently and use them to instruct

others who may use this tool. If you lend this tool to someone else, also lend

these instructions to them to prevent misuse of the product and possible injury.

SAVE THESE INSTRUCTIONS!

NOTE: SEE YOUR POWER HEAD OPERATOR’S MANUAL FOR

ADDITIONAL SPECIFIC SAFETY RULES.

INTRODUCTION

Congratulations on your selection of the EGO EDGER ATTACHMENT. It has been

designed, engineered and manufactured to give you the best possible dependability

and performance.

Should you experience any problem you cannot easily remedy, please contact EGO

customer service center 1-855-EGO-5656.

EDGER ATTACHMENT—EA0800 9

This manual contains important information on to the safe assembly, operation and

maintenance of your product. Read it carefully before using the product. Keep this

manual handy so you can refer to it at any time.

SERIAL NUMBER _____________________ DATE OF PURCHASE _________________

YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP THEM IN A

SAFE PLACE FOR FUTURE REFERENCE

SPECIFICATIONS

Blade Length 8”

Edging Depth Up to 4”

Weight 4.99 lb. (2.26 kg)

PACKING LIST

PART NAME QUANTITY

Edger Attachment 1

Hex Wrench 1

Multi-function Wrench 1

Cotter Pin 2

Operator's Manual 1

Recommended Blade

PART NAME MODEL NUMBER

Edger Blade AEB0800

EDGER ATTACHMENT—EA080010

DESCRIPTION

KNOW YOUR EDGER ATTACHMENT (Fig.1)

The safe use of this product requires an understanding of the information on the tool and

in this operator’s manual, as well as knowledge of the project you are attempting. Before

using this product, familiarize yourself with all operating features and safety rules.

1

Multi-function Wrench

Hex Wrench

Edger Shaft

Depth-adjusting Guide Bar

Debris Flap

Screw to lock guide plate in place

Guide Plate

End Cap

Blade

Blade Guard

Guide Wheel

Depth-adjusting Knob

EDGER ATTACHMENT—EA0800 11

BLADE

Metal cutting blade for cutting weeds and soft green plants.

BLADE GUARD

Reduces the risk of injury from foreign objects ﬂung backwards toward the operator by

the cutting attachment and from contact with the cutting attachment.

DEBRIS FLAP

Reduces the risk of injury from foreign objects ﬂung back towards the operator by the

cutting blade.

DEPTH-ADJUSTING KNOB & DEPTH-ADJUSTING GUIDE BAR

Adjusts the depth of cut.

GUIDE WHEEL

Rolls on ground and keeps edger blade at preset height for required depth of cut.

GUIDE PLATE

Optional guide for cutting against pavement. (See "REMOVING THE GUIDE PLATE" if the

guide plate is not needed.)

EDGER ATTACHMENT—EA080012

ASSEMBLY

WARNING:

If any parts are damaged or missing, do not operate this product

until the parts are replaced. Use of this product with damaged or missing parts could

result in serious personal injury.

WARNING:

Do not attempt to modify this product or create accessories not

recommended for use with this edger. Any such alteration or modiﬁcation is misuse and

could result in a hazardous condition leading to possibly serious personal injury.

WARNING:

Do not adjust the blade guard. The blade guard has been set at

the factory so that the arrow on the blade guard and the open side point away from the

operator. This ensures that cuttings and other debris are directed away from the power

tool and the operator.

UNPACKING



This product requires assembly.



Carefully remove the product and any accessories from the box. Make sure that

all items listed in the packing list are included.



Inspect the tool carefully to make sure that no breakage or damage occurred

during shipping



Do not discard the packing material until you have carefully inspected and

satisfactorily operated the tool.



If any parts are damaged or missing, please return the product to the place of

purchase.

CONNECTING THE EDGER ATTACHMENT TO THE POWER HEAD

WARNING:

Never attach or adjust any attachment while the power head is

running or with the battery installed. Failure to stop the motor and remove the battery

may cause serious personal injury.

This edger attachment is designed for use with EGO Power Head PH1400.

The edger attachment connects to the power head by means of a coupler device.

1. Stop the motor and remove the battery pack.

EDGER ATTACHMENT—EA0800 13

2. Loosen the wing knob.

3. Remove the end cap from the edger attachment. Align the arrow on the edger

shaft with the arrow on the coupler and push the edger shaft into the coupler until

you hear a clear “click” sound which indicates the edger shaft is mounted into

place (Fig. 2).

4. Pull the shaft of the attachment to verify it is securely locked into the coupler. If

not, rotate the edger shaft from side to side in the coupler until it snaps into place.

5. Tighten the wing knob securely.

WARNING:

Be certain the wing knob is fully tightened before operating

equipment; check it periodically for tightness during use to avoid serious personal

injury.

REMOVING THE ATTACHMENT FROM THE POWER HEAD

1. Stop the motor and remove the battery pack.

2. Loosen the wing knob.

3. Press the shaft-release button and with the button depressed, pull or twist the

attachment shaft out of the coupler.

2

Arrow on the Coupler

Arrow on the Attachment Shaft

Edger Shaft

Shaft-Release Button

Power Head Shaft

Wing Knob

EDGER ATTACHMENT—EA080014

OPERATION

WARNING:

Do not allow familiarity with this product to make you careless.

Remember that a careless fraction of a second is sufﬁcient to inﬂict serious injury.

WARNING:

Always wear safety goggles or safety glasses with side shield

marked to comply with ANSI Z87.1. Failure to do so could result in objects being thrown

into your eyes and other possible serious injuries.

WARNING:

Do not use any attachments or accessories not recommended by the

manufacturer of this product. The use of attachments or accessories not recommended

can result in serious personal injury.

APPLICATIONS

You may use this product for the purpose listed below:



Edging around walkways, curbing, ﬂower beds and other similar areas.

Before each use check for damaged/worn parts

Check the blade, guard and front-assist handle and replace any parts that are cracked,

warped, bent, or damaged in any way.

WARNING:

To prevent serious personal injury, remove the battery pack from the

tool before servicing, cleaning, changing attachments or removing material from the

unit.

USING THE EDGER ATTACHMENT WITH POWER HEAD

WARNING:

Dress properly to reduce the risk of injury when operating this tool.

Do not wear loose clothing or jewelry. Wear eye and ear/hearing protection. Wear heavy,

long pants, boots and gloves. Do not wear short pants or sandals or go barefoot. Wear a

face mask or dust mask in dusty locations.

EDGER ATTACHMENT—EA0800 15

WARNING:

Clear away all

obstacles and solid objects from the work

area.

Hold the edger with your right hand on the

rear handle and your left hand on the front-

assist handle. Keep a ﬁrm grip with both

hands while operating the tool. The edger

should be held at a comfortable position

with the rear handle at about hip height

(Fig. 3).

ADJUSTING DEPTH OF CUT

1. Stop the motor and remove the

battery pack.

2. Loosen the depth-adjusting knob in

the direction of the unlocking arrow

marked on the knob (Fig.4).

3. Move the guide wheel, along the

depth-adjusting guide bar, up to

increase the depth of cut or down to

decrease the depth (Fig. 5).

The depth of cut depends on the

unevenness of the ground, your height

and the way you hold the edger. Use the

following procedures:

4

Depth-adjusting Knob

5

Depth-adjusting Guide Bar

To Decrease Depth

To Increase Depth

3

EDGER ATTACHMENT—EA080016

4. Adjust the guide wheel so that the

blade just touches the ground or

breaks the surface of the soil by no

more than 1/4" (5mm) (Fig.6).

5. Tighten the depth-adjusting knob

clockwise securely, in the direction

of the locking arrow marked on the

knob

6. Standing in the normal working

position, check the depth of cut

again and correct it if necessary.

TO START/STOP THE TOOL

See "STARTING/STOPPING THE POWER

HEAD" section in the power head PH1400

operator's manual.

OPERATING TIPS



Hold and guide the power head so

that the blade is vertical.



Operate at no more than a normal walking pace.



Cut at a steady pace. If the blade begins to bog down, you are edging too fast;

slow your pace.



Do not force the blade into the ground. Light contact of the blade against the

sidewalk edge, curb, etc., is acceptable and will not damage the edger.



Always walk forwards when cutting and move the edger forward. Do not pull the

edger towards you.



Use the sight line to line the blade up with the edge of the bed (Fig. 7).



Best appearance is obtained when grass is dry. Avoid edging in wet soil or wet

grass areas or the blade guard might clog and result in an uneven edge. If the

blade guard becomes clogged, stop the motor, remove the battery pack, and

remove debris from the blade guard.

7

Sight Line

6

Guide

Wheel

No more than 1/4" (5mm)

Blade

EDGER ATTACHMENT—EA0800 17

MAINTENANCE

WARNING: When servicing, use only identical replacement parts. Use of any

other parts may create a hazard or cause product damage. To ensure safety and

reliability, all repairs should be performed by a qualiﬁed service technician.

WARNING: Battery tools do not have to be plugged into an electrical outlet;

therefore, they are always in operating condition. To prevent serious personal injury,

take extra precautions and care when performing maintenance, service or for changing

the cutting attachment or other attachments.

WARNING: To prevent serious personal injury, remove the battery pack from

the power head before servicing, cleaning, changing add-on attachments or when the

product is not in use.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to

damage from various types of commercial solvents and may be damaged by their use.

Use clean cloths to remove dirt, dust, oil, grease, etc.

WARNING: Do not at any time let brake ﬂuids, gasoline, petroleum-based

products, penetrating oils, etc., come in contact with plastic parts. Chemicals can

damage, weaken, or destroy plastic, which may result in serious personal injury.

WARNING: When cleaning the edger attachment, DO NOT immerse in water or

other liquids.

CLEAN THE UNIT



After each use, remove the battery and clean the debris, clogged soils or grass on

the blade and guard with a soft brush. Wipe the edger surface with a clean cloth

moistened with a mild soap solution.



Use a small brush or a small vacuum cleaner to clean the air vents on the rear

housing.



Keep the air vents free of obstructions.

EDGER ATTACHMENT—EA080018

All edger service, other than the items listed in these maintenance instructions, should

be performed by competent edger service personnel.

REPLACING THE BLADE

WARNING: Do not attempt to straighten or weld a bent or cracked blade. Such

a blade may break and it must be replaced. Recommend replace only with EGO edger

blade, see “Recommended Blade” section.

NOTICE: Replace the blade if its length

is no longer sufﬁcient to maintain the

necessary ground clearance and obtain

the required depth of cut.

WARNING: Always protect

your hands by wearing heavy gloves

or wrapping the blade with rags or

other materials when performing any

maintenance on the edger blade.

Removing the blade

1. Stop the motor and remove the

battery pack.

2. Lay the edger on its back so that the

blade is facing upwards.

3. Wear protective gloves. Use a

needle nose pliers (not included)

to remove the cotter pin from the

motor shaft (Fig.8).

4. Rotate the blade to align the slot in the ﬂange with the hole in the gear case

(Fig. 8).

5. Insert the hex wrench provided into the aligned holes to act as a stabilizer. Use

the multi-function wrench provided to loosen the nut CLOCKWISE (Fig.9).

8

Aligned Shaft-locking Holes

Gear Case

Inner Flange

9

Stabilizer

Multi-function

Wrench Provided

Cotter Pin

EDGER ATTACHMENT—EA0800 19

6. Remove the nut, outer ﬂange, blade

and the inner ﬂange from the motor

shaft (Fig. 10). Check and replace

them if they are worn.

Installing the blade

1. Position the inner ﬂange removed in

step 6 of the “Removing the blade”

section onto the motor shaft with

the bulge of the inner ﬂange facing

outwards (Fig.11).

2. Install the new blade onto the inner

ﬂange.

WARNING: The bulge of the inner

ﬂange must engage the blade’s mounting

hole (Fig.12). There should not be any

clearance between the blade and the

inner ﬂange ﬂat surface.

3. Mount the outer ﬂange and the nut

onto the shaft, and pre-tighten the

nut COUNTERCLOCKWISE by hand.

4. Rotate the blade to align the slot in

the ﬂange with the hole in the gear

case (Fig. 8)

5. Insert the hex wrench provided

into the aligned holes to act as a

stabilizer. Use the multi-function

wrench provided to tighten the nut

COUNTERCLOCKWISE securely onto

the shaft (Fig.13).

6. Insert a new cotter pin into the hole

in the motor shaft. Bent the two feet

of the pin in opposite directions with

a needle nose pliers (not included)

(Fig. 8).

13

Stabilizer

Multi-function

Wrench Provided

10

Slot in the Inner Flange

Outer Flange

Nut

Cotter Pin

Inner Flange

Blade

Motor Shaft

11

Bulge Outwards

12

Inner Flange

Blade

Bulge of the inner ﬂange

engaging the blade

EDGER ATTACHMENT—EA080020

REPLACING THE GUIDE WHEEL

1. Stop the motor and remove the

battery pack.

2. Lay the edger on its back so that the

guide wheel is facing upwards.

3. Loosen the depth-adjusting knob in

the direction of the unlocking arrow

marked on the knob and removing

it.

4. Remove the spring washer, plain

washer 1, guide wheel, bushing and

plain washer 2 from the screw pole

(Fig. 14). Check and replace them if

they are worn.

5. Mount the screw pole through the

depth-adjusting guide bar ﬁrst, and

then mount the plain washer 2,

bushing and new wheel, then mount

the plain washer 1, spring washer and depth-adjusting knob onto the screw pole

in the sequence shown in Fig. 14.

NOTICE: The guide wheel should be mounted with its ﬂat ribs facing inwards (Fig. 15).

6. Lock the depth-adjusting knob in the direction of the locking arrow marked on the

knob.

REPLACING THE DEBRIS FLAP

1. Stop the motor and remove the battery pack.

2. Use the hex wrench provided to loosen the two screws.

3. Remove the screws, ﬁxing board and worn debris ﬂap (Fig.15).

4. Replace with a new debris ﬂap and lock it with the ﬁxing board and the two

screws.

14

Depth-adjusting Knob

Spring Washer

Plain Washer 1

Guide Wheel

Bushing

Plain Washer 2

Depth-adjusting

Guide Bar

Screw Pole

15

Fixing Board

Debris Flap

Flat Rib

Screws

La page charge ...

EGO ME0801 Le manuel du propriétaire

Ce manuel convient également à

EGO ME0801 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents