Jenn-Air JUDFP242HL Le manuel du propriétaire

Marque: Jenn-Air

Modèle: JUDFP242HL

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à





DOUBLE REFRIGERATOR DRAWERSREFRIGERATOR

FREEZER DRAWERS

’’

’

TIROIRS RÉFRIGÉRANTS DOUBLESRÉFRIGÉRATEUR

TIROIRS DE CONGÉLATION

For questions about features, operation/performance, parts, accessories, or service, call:

1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.

In Canada, call: 1-800-JENNAIR (1-800-536-6247), or visit our website at www.jennair.ca.

Pour des questions à propos des caractéristiques, du fonctionnement/rendement,

des pièces, accessoires ou service, composer le:

1800JENNAIR (1800536-6247) ou visiter notre site Web au www.jennair.com.

Au Canada, composer le: 1800JENNAIR (1800536-6247) ou visiter notre site Web au www.jennair.ca.

W11357308B

TABLE DES MATIÈRES

INTRODUCTION

Sécurité ...............................................................................................................23

Mise au rebut du vieux réfrigérateur..............................................24

Conﬁguration .................................................................................................24

Caractéristiques ............................................................................................25

EXIGENCES D’INSTALLATION

Outils et pièces ..............................................................................................26

Exigences d’emplacement ....................................................................26

Dimensions du produit ............................................................................27

Panneaux décoratifs de tiroirs personnalisés ...........................28

Spéciﬁcations électriques ......................................................................29

Spéciﬁcations de l’alimentation en eau

(réfrigérateur et tiroir decongélation seulement) ...............29

INSTRUCTIONS D’INSTALLATION

Déballage du tiroir de réfrigération ................................................30

Raccordement de l’alimentation en eau

(réfrigérateurettiroir de congélation seulement) .... 30

Déplacement des tiroirs de réfrigération à leur

emplacementﬁnal .....................................................................................31

Installation du panneau décoratif personnalisé .....................31

Réglage de l’aplomb des tiroirs deréfrigération ...................32

Terminer l’installation ................................................................................32

UTILISATION DES TIROIRS

DE RÉFRIGÉRATION

Commandes ....................................................................................................33

Sons normaux ................................................................................................35

Pour assurer une circulation d’aircorrecte ................................35

Machine à glaçons ......................................................................................35

ENTRETIEN ET NETTOYAGE

Nettoyage ..........................................................................................................36

Remplacement du ﬁltre à eau ............................................................ 36

Pannes de courant ......................................................................................37

Entretien avant les vacances ...............................................................37

DÉPANNAGE

Utilisation ...........................................................................................................37

Température et humidité .......................................................................37

Tiroirs ....................................................................................................................38

ASSISTANCE

Aux É.-U. ..............................................................................................................39

Au Canada .........................................................................................................39

Accessoires .......................................................................................................39

Fiches de données de produitS .........................................................40

Garantie ..............................................................................................................41

TABLE OF CONTENTS

INTRODUCTION

Safety ....................................................................................................................3

Proper Disposal of your

old Refrigerator .............................................................................................4

Design conﬁguration ................................................................................4

Features ..............................................................................................................5

INSTALLATION REQUIREMENTS

Tools and Parts ...............................................................................................6

Location Requirements ...........................................................................6

Product Dimensions ..................................................................................7

Custom Overlay Drawer Panels..........................................................8

Electrical Requirements ..........................................................................9

Water Supply Requirements

(Refrigerator/Freezer Drawers only) ................................................9

INSTALLATION INSTRUCTIONS

Unpack The Refrigerator Drawers ...................................................10

Connect Water Supply

(Refrigerator/Freezer Drawers only) ................................................10

Move the Refrigerator Drawers to Final Location .................11

Install Custom Overlay Panel ...............................................................11

Level the Refrigerator Drawers ..........................................................12

Complete Installation ................................................................................12

REFRIGERATOR DRAWERS USE

Controls ...............................................................................................................13

Normal Sounds ..............................................................................................15

Ensuring Proper Air Circulation .........................................................15

Ice Maker ............................................................................................................ 15

CARE AND CLEANING

Cleaning .............................................................................................................16

Changing the Water Filter .....................................................................16

Power Interruptions ...................................................................................16

Vacation Care ..................................................................................................17

TROUBLESHOOTING

Operation ...........................................................................................................17

Temperature Moisture ..............................................................................17

Drawers ...............................................................................................................18

ASSISTANCE

In the U.S.A. ......................................................................................................19

In Canada ...........................................................................................................19

Accessories .......................................................................................................19

Product Data Sheet ....................................................................................20

Warranty .............................................................................................................21

INTRODUCTION

SAFETY

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

To reduce the risk of fire, electric shock, or injury when using your refrigerator drawer(s), follow these basic

precautions:

SAVE THESE INSTRUCTIONS

■ Plug into a grounded 3 prong outlet.

■ Do not remove ground prong.

■ Do not use an adapter.

■ Do not use an extension cord.

■ Disconnect power before servicing.

■ Connect to potable water supply.

■ Replace all parts and panels before operating.

■ Remove door or drawer(s) from your old refrigerated

appliance.

■ Use non flammable cleaner.

■ Do not store or use petrol, flammable liquids or gas in the

vicinity of this or other electrical appliances. The fumes can

cause fires or explosions.

■ Do not store explosive substances such as aerosol cans with

a flammable propellant in this refrigerator drawer(s).

■ Do not use or place electrical devices inside the refrigerator

drawer(s) compartments if they are not of the type expressly

authorized by the manufacture.

■ Use two or more people to move and install refrigerator

drawer(s).

■ This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

■ Children should be supervised to ensure that they do not

play with the appliance.

■ To avoid the risk of children becoming trapped and

suffocating, do not allow them to play or hide inside the

refrigerator drawer(s).

■ If the power supply cord is damaged, it must be replaced by

the manufacturer or its service agent or a similarly qualified

person.

■ Keep ventilation openings, in the appliance enclosure or in

the built-in structure, clear of obstruction.

■ Do not use mechanical devices or other means to accelerate

the defrosting process, other than those recommended by

the manufacturer.

■ Do not damage the refrigerant circuit.

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

PROPER DISPOSAL OF YOUR

OLD REFRIGERATOR

IMPORTANT: Child entrapment and suffocation are not

problems of the past. Junked or abandoned refrigerators

are still dangerous – even if they will sit for “just a few

days.” If you are getting rid of your old refrigerator, please

follow these instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerator:

 Remove the door or drawer(s).

DESIGN CONFIGURATION

DOUBLE REFRIGERATOR DRAWERS

Refrigerator drawers provide additional storage options in the kitchen or other areas of the home.

REFRIGERATORFREEZER DRAWERS WITH ICE MAKER AND WATER FILTER

Upper refrigerator drawer and lower freezer drawer provide additional storage options in the kitchen or other areas of

the home. Factory-installed ice maker in lower drawer ensures a constant supply of ice on hand at all times.

WARNING

Suffocation Hazard

Remove door or drawer(s) from your old refrigerated

appliance.

Failure to do so can result in death or brain damage.

Important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

JUDFP242HM

JUCFP242HM

JUDFP242HL JUDFP242HX

JUCFP242HL JUCFP242HX

6,7,8.

12.

FEATURES

1. Stealth Flush Design

Create an unbroken silhouette. Discreet 1/8" envelop

every side, without exposed hinges or trim pieces.

2. Daring Obsidian Interior

Inspired by volcanic glass, this dark ﬁnish erupts

with reﬂective, high-contrast style. Let the object of

your desire emerge like vibrant art, begging to be

consumed.

3. Sabbath Mode

Allows the refrigerator or freezer to be opened or

closed on the Sabbath or other religious holidays

without directly turning on or off any lights, digital

readouts, fans, valves, tones or alarms.

4. Over Temp Alarm

Chimes when the temperature in either drawer rises

above 45°F (7°C) for longer than 10 minutes.

5. LED Lighting

LED lights instinctively come alive, chasing away

shadows to reveal vivid details.

6. RISE™ Design Expression

Embrace an era of striking proportions. A stainless

steel suite of armor gleams with spectacular light.

This is strength—inextricable from beauty. Forged

in the ﬁres of progress, the RISE™ design expression

towers over stagnant, uninspired designs that have

inherited undeserved standing.

7. NOIR™ Design Expression

Lose yourself in a world that’s yours alone. Crisp

silhouettes crackle with mystique; beguiling

reﬂections ﬂow in and out of sight. Taut with

ceaseless allure and minimalist appeal, the NOIR™

design expression rejects dated ideals of beauty.

8. Custom Panel Overlay

Break free with custom panels that allow

unapologetic expression. Custom panels and handles

must be purchased separately.

9. Drawer Open Alarm

Helps prevent food spoilage by sounding an alarm

at 2-minute intervals when either drawer is open for

longer than 5 minutes.

10. Drawer Dividers

Divide and conquer. Add or remove barriers to

organize each drawer as you see ﬁt.

11. Hushed Acoustics

Our internal compressor keeps your beverages

impeccably chilled, while running unobtrusively in

the background. Brilliance doesn’t have to announce

itself; it just is.

12. Max Cool Option

Plummet internal temperatures to their lowest point

for 24 hours.

11.

10.

INSTALLATION REQUIREMENTS

TOOLS AND PARTS

Gather the required tools and parts before starting

installation.

Read and follow the instructions provided with any tools

listed here.

TOOLS AND PARTS NEEDED:

 Phillips screwdriver

 Cordless drill

 1/8" Drill bit

 Tape measure

 Level

ADDITIONAL TOOLS NEEDED CUSTOM OVERLAY

PANEL ONLY:

 Scissors

 Pencil

 Scribe

PARTS NEEDED CUSTOM OVERLAY PANEL ONLY:

 Custom Overlay Drawer Panels — See “Custom

Overlay Drawer Panels.”

 Hardware

PARTS NEEDED CUSTOM OVERLAY PANEL ONLY:

 Hooks (8)

 Screws (16)

 Self-tap wood screws (4)

LOCATION REQUIREMENTS

IMPORTANT: This appliance is intended to be used in

household and similar applications such as:

 Staff kitchen areas in shops, ofﬁce and other working

environments;

 Farm houses and by clients in hotels, motels and

other residential type environments;

 Bed and breakfast type environments;

 Catering and similar non-retail applications.

NOTES:

 For the refrigerator drawers to be ﬂush with the

front of the base cabinets remove any baseboards or

moldings from the rear of the opening. See “Product

Dimensions” and later in this section “Opening

Dimensions”

 It is recommended that you do not install the

refrigerator drawers near an oven, radiator, or other

heat source.

 Do not install in a location where the temperature will

fall below 55°F (13°C).

OPENING DIMENSIONS

 Height dimensions are shown with the leveling legs

extended to the minimum height of 1/4" (6 mm)

below the refrigerator drawers.

NOTE: When leveling legs are fully extended to 1" (25

mm) below the refrigerator drawers, add 3/4" (19 mm)

to the height dimensions. See “Product Dimensions.”

 If the ﬂoor of the opening is not level with the kitchen

ﬂoor, shim the opening to make it level with the

kitchen ﬂoor.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator drawer(s).

Failure to do so can result in death, explosion, or fire.

Critical Dimensions:

A. Utility opening

B. Minimum opening width

14⁄"

(375 mm)

1/2"

(13 mm)

34⁄" (873 mm) min.

35" (889 mm) max.

24" (609.6 mm) min.

PRODUCT DIMENSIONS

DRAWER HEIGHT DIMENSIONS

 Height dimensions are shown with the leveling

legs extended to 1/4" (6 mm) below the refrigerator

drawers.

 When leveling legs are fully extended to 1" (25 mm)

below the refrigerator drawers, add 3/4" (19 mm) to

the height dimensions.

 The power cord is 60" (1.52 m) long.

RISE™NOIR™OVERLAY FRONT VIEW

DRAWER WIDTH DIMENSIONS

RISE

NOIR

TOP VIEW

OVERLAY TOP VIEW

*DIMENSION INCLUDES 34" 19 MM THICK CUSTOM

DRAWER PANEL

1/4"

(6 mm)

15"

(380 mm)

15"

(380 mm)

30¼"

(760 mm)

"

(868 mm)

"

(606 mm)

"

(606 mm)

"

(676 mm)

"

(603 mm)

"*

(588.2 mm)

"

(550 mm)

"

(550 mm)

CUSTOM OVERLAY DRAWER PANELS

If you plan to install custom wood panels, you will need

to create the panels yourself or consult a qualiﬁed

cabinetmaker or carpenter. See dimension drawings for

panel speciﬁcations.

IMPORTANT:

 The thickness of the overlay panels must be 3/4"

(19 mm).

 To avoid damage to the drawers, each overlay panel

must not weigh more than 10 lbs (4.5 kg).

 Do not exceed the height dimension for the overlay

panels. Panels that exceed the height dimension

may damage the refrigerator drawers, cabinets or

countertop.

 The width of the overlay panels may vary according to

the width of the cabinet opening.

 For the installation of the customer panel, you will

need the following parts:

 16 screws (SS Flat M4x12 tapping 1)

 4 Self-tap wood screws

 4 Drawer overlay hook plate right (SPHC T=2.3)

 4 Drawer overlay hook plate left (SPHC T=2.3)

NOTE: Some or all parts may or may not be included.

If your product does not include these parts, contact

Assistance or Service or ask a specialist.

TOP AND BOTTOM OVERLAY DRAWER PANEL DIMENSIONS

A. SS Flat M4x12 tapping screws

B. Self-tap wood screws

C. Overlay hook plate right

D. Overlay hook plate left

A.Router 1/8" (2.5 mm) deep.

A B

C D

" (603 mm)

" (536.4 mm)

1/8" (2.5 mm) Holes [Depth 3/8" (10 mm)]

" (95 mm)

" (107 mm)

" (86 mm)

(26 mm)

15/16"

(24.3 mm)

"

(44 mm)

3/8"

(9 mm)

15" (380.5 mm)

15/16" (23.3 mm)

13/16" (20 mm)

7/16" (12 mm)

Top

Back Panel

Bottom

ELECTRICAL REQUIREMENTS

Before you move your refrigerator drawers into its ﬁnal

location, it is important to make sure you have the proper

electrical connection.

RECOMMENDED GROUNDING METHOD

A 115 V, 60 Hz, AC only, 15 or 20 A fused, grounded

electrical supply is required. It is recommended that a

separate circuit serving only your refrigerator drawers be

provided. Use an outlet that cannot be turned off by a

switch. Do not use an extension cord.

NOTE: Before performing any type of installation,

cleaning, or removing a light bulb, unplug refrigerator

drawers or disconnect power.

WATER SUPPLY REQUIREMENTS

REFRIGERATORFREEZER DRAWERS

ONLY

Gather the required tools and parts before starting

installation. Read and follow the instructions provided

with any tools listed here.

IMPORTANT:

 Connect to potable water supply.

 If you turn ON the refrigerator drawers before the

water line is connected, turn OFF the ice maker.

 All installations must meet local plumbing code

requirements.

 Use copper tubing and check for leaks. Install

copper tubing only in areas where the household

temperatures will remain above freezing.

TOOLS NEEDED: Flat-blade screwdriver, 7/16" and 1/2"

open-end wrenches or two adjustable wrenches, 1/4" nut

driver and drill bit, cordless drill.

NOTE: Your refrigerator dealer has a kit available with a

1/4" (6 mm) saddle-type shutoff valve, a union, and copper

tubing. Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes. Do not use

a piercing-type or 3/16" (4.76 mm) saddle valve which

reduces water ﬂow and clogs more easily.

WATER PRESSURE

A cold water supply with water pressure of between 30

and 120 psi (207 and 827 kPa) is required to operate ice

maker. If you have questions about your water pressure,

call a licensed, qualiﬁed plumber.

REVERSE OSMOSIS WATER SUPPLY

IMPORTANT: The pressure of the water supply coming

out of a reverse osmosis system going to the water inlet

valve of the refrigerator needs to be between 30 and 120

psi (207 and 827 kPa).

If a reverse osmosis water ﬁltration system is connected

to your cold water supply, the water pressure to the

reverse osmosis system needs to be a minimum of 40 to

60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less

than 40 to 60 psi (276 to 414 kPa):

 Check to see whether the sediment ﬁlter in the

reverse osmosis system is blocked. Replace the ﬁlter if

necessary.

 Allow the storage tank on the reverse osmosis system

to reﬁll after heavy usage.

If you have questions about your water pressure, call a

licensed, qualiﬁed plumber.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

INSTALLATION INSTRUCTIONS

UNPACK THE REFRIGERATOR DRAWERS

REMOVE THE PACKAGING

Remove tape and glue residue from surfaces before

turning on the refrigerator drawers. Rub a small amount

of liquid dish soap over the glue residue with your

ﬁngers. Wipe with warm water and dry. Do not use

sharp instruments, rubbing alcohol, ﬂammable ﬂuids, or

abrasive cleaners to remove tape or glue.

These products can damage the surface of your

refrigerator drawers. Properly dispose of packaging.

CLEAN BEFORE USING

After you remove all of the package materials, clean the

inside of your refrigerator drawers before using them. See

“Cleaning.”

CONNECT WATER SUPPLY REFRIGERATOR

FREEZER DRAWERS ONLY

CONNECT TO WATER LINE

1. Unplug refrigerator drawers or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet

long enough to clear line of water.

3. Locate a 1/2" to 1¹⁄₄" (12.5 mm to 31.8 mm) vertical cold

water pipe near the refrigerator drawers.

IMPORTANT:

 Make sure it is a cold water pipe.

 Horizontal pipe will work, but drill on the top side

of the pipe, not the bottom. This will help keep

water away from the drill and normal sediment

from collecting in the valve.

4. Determine the length of copper tubing you need.

Measure from the connection on the lower left rear of

refrigerator drawers to the water pipe. Add 7 ft

(2.1 m) to allow for cleaning. Use 1/4" (6 mm)

O.D. (outside diameter) copper tubing. Be sure both

ends of copper tubing are cut square.

5. Using a cordless drill, drill a 1/4" hole in the cold water

pipe you have selected.

6. Fasten the shutoff valve to the cold water pipe with

the pipe clamp. Be sure the outlet end is solidly in the

1/4" drilled hole in the water pipe and that the washer

is under the pipe clamp. Tighten the packing nut.

Tighten the pipe clamp screws slowly and evenly so

washer makes a watertight seal. Do not overtighten

or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut

on the copper tubing as shown. Insert the end of

the tubing into the outlet end squarely as far as it

will go. Screw compression nut onto outlet end with

adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink,

and turn ON the main water supply. Flush the tubing

until water is clear. Turn OFF the shutoff valve on the

water pipe. Coil the copper tubing.

CONNECT TO REFRIGERATOR

1. Attach the copper tube to the valve inlet using a

compression nut and sleeve as shown. Tighten the

compression nut. Do not overtighten. Use the tube

clamp on the back of the refrigerator drawers to

secure the tubing to the refrigerator drawers. This

will help avoid damage to the tubing when the

refrigerator drawers are pushed back against the wall.

2. Turn ON shutoff valve.

3. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator drawer(s).

Failure to do so can result in back or other injury.

When Moving Your Refrigerator Drawers:

Your refrigerator drawers are heavy. When moving the

appliance for service, be sure to cover the ﬂoor with

cardboard or hardboard to avoid ﬂoor damage. Always pull

the appliance straight out when moving it. Do not wiggle or

“walk” the appliance when trying to move it, as ﬂoor

damage could occur.

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

F. Shutoff valve

G. Packing nut

A. Plug

B. Compression nut

C. Pex tubing

DEF

4. The ice maker is equipped with a built-in water

strainer. If your water conditions require a second

water strainer, install it in the 1/4" (6 mm) water line at

either tube connection. Obtain a water strainer from

your nearest appliance dealer.

5. Plug in refrigerator drawers or reconnect power.

MOVE THE REFRIGERATOR DRAWERS TO

FINAL LOCATION

1. Place top of cardboard carton or plywood under the

appliance. Remove dolly.

2. Do not remove ﬁlm or cover.

3. Plug into a grounded 3 prong outlet.

4. Move the refrigerator drawers straight back and

evenly in front of the opening.

INSTALL CUSTOM OVERLAY PANEL

IMPORTANT:

 For standard stainless steel models, skip these

instructions and go to "LEVEL THE REFRIGERATOR

DRAWERS" section.

 Create a custom overlay panel according to the

speciﬁcations in “Custom Overlay Drawer Panels.”

 JennAir is not responsible for the removal or addition

of molding or decorative panels that would not allow

access to the refrigerator drawers for service.

ATTACH THE OVERLAY PANEL

NOTE: If the overlay hooks are not installed, see “Custom

Overlay Drawer Panels” for overlay hook locations. The

location of the hooks must be as precise as possible. If

the custom panel is incorrectly placed, the panel may

interfere with optimal use of the drawers.

1. Attach the custom handle of your preference on the

overlay before attaching the overlay to the drawer of

the refrigerator.

NOTE: Custom handles may vary in dimensions. Holes

must be made on the panel according to the speciﬁc

dimensions of your handle.

2. Attach the hooks to their corresponding recessions

on the panel, using the SS Flat M4x12 screws. Two

screws are needed per hook. The hooks must be on

the outer edge of the panel.

3. Gently pull back the gasket from the top corners of

the door until you can see the screw that is behind

the gasket. There is one screw on each side. It is not

necessary to remove the gasket.

4. Remove the screws behind the gasket (one per side).

5. Align the panel to the drawer and position the overlay

panel 1/2" (12.5 mm) higher than the door. Position

the overlay hooks with the pilot holes and push the

hooks into the holes. The drawer has insulant foam

in its interior so you may feel some interference while

pushing. Push until the hooks go through the foam.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

6. Push straight down on the overlay panel to secure

the overlay hooks to the drawer.

7. Using the self-tap wood screws (two per drawer; one

in each corner of the drawers), attach the panel to the

drawer.

NOTE: Do not put the screws removed in step 4 back on

the door.

8. Once the overlay is securely attached to the drawer

with the two screws, put the gasket back in its place

by pressing it against the door until the gasket is even

and ﬁrmly secured.

LEVEL THE REFRIGERATOR DRAWERS

IMPORTANT:

 Overlay Model—Be sure to install the custom overlay

drawer panels before leveling the refrigerator

drawers. See “Install Custom Overlay Panel.”

 Before installing the refrigerator drawers, be sure that

the countertop is level.

 If the countertop is not level, adjust the refrigerator

drawers’ leveling legs until the appliance is square

with the countertop. Be sure to maintain 3/8" (9.5

mm) minimum gap between the top of the drawer

and the countertop.

1. Open the top drawer and place the level across the

top drawer as shown. Check the level from left to

right.

2. Turn the leveling legs (front and back) until the top

drawer measures level from left to right.

3. Remove the level and close the top drawer. Check

the gap between the top of the drawer and the

countertop. If the gap measures less than 3/8"

(9.5 mm) minimum, turn all four leveling bolts

equally to the left to raise the leveling legs (this will

lower the appliance). Recheck the level.

4. Open both drawers less than midway. Place the level

on the side ﬂange beside the drawers as shown. Turn

the front leveling bolts together in order to either

raise or lower the appliance until the sides of the

refrigerator drawers are plumb.

5. Remove the level and close the drawers. Recheck

the gap between the top of the drawer and the

countertop. If the gap measures less than 3/8"

(9.5 mm), turn all four leveling bolts equally to raise

the leveling legs (this will lower the appliance).

Recheck the level.

NOTE: Be sure to recheck the horizontal level of the

top drawer.

6. Be sure all four levelers are on the ﬂoor and

supporting the full weight of the refrigerator drawers.

COMPLETE INSTALLATION

1. Remove all boxes, parts packages and packing

materials from the interior of the refrigerator drawers.

2. Remove the ﬁlm.

3. Clean the refrigerator drawers before use. Refer

"CARE AND CLEANING" section.

4. The controls are preset at the factory to the

recommended settings. Be sure that the compressor

is operating properly and that all the lights are

working.

5. If construction will continue after the refrigerator

drawers have been installed, turn OFF the power for

both drawers.

To get the most efﬁcient use from your new refrigerator

drawers, read the “Refrigerator Drawers Use” section.

A. Check the level from left to right.

A. Check the level from front to back.

REFRIGERATOR DRAWERS USE

CONTROLS

The control panels for both double drawer models are

located in the upper drawer. To view and set the Upper

and Lower control panel, pull out the upper drawer.

IMPORTANT:

 Wait 24 hours after you turn on the refrigerator

drawers before you put food into the drawers. If you

add food before the drawers have cooled completely,

your food may spoil.

NOTE: Adjusting the controls to a lower (colder)

setting in one or both drawers will not cool them any

faster.

 If the temperature is too warm or too cold in the

drawers, ﬁrst check the air vents to be sure they are

not blocked before adjusting the controls.

 The preset settings should be correct for normal

household usage. The refrigerator control is set

correctly when milk or juice is as cold as you like.

 The freezer control is set correctly when ice cream is

ﬁrm.

 The actual temperature may differ from the display

when a drawer is open for an extended period of

time.

1. Turning Drawers On/Off

 The ﬁrst time that the drawers are plugged in, the

control will be in Cool Off mode. Cool On and Cool

Off will be the only options that display.

 Press COOL ON for 3 seconds to turn on

the drawers. All menus and recommended

temperature settings will be displayed.

 The left temperature and preset touch

pads control the temperature of the upper

compartment.

 The right temperature and preset touch

pads control the temperature of the lower

compartment.

1 2 4 5 75

Refrigerator drawer models

1 2 43 45 75

8 9

Refrigerator/freezer combo models

2. Max Cool

The Max Cool feature assists with periods of heavy

usage, full grocery loads or temporarily warm room

temperatures.

Max Cool will reset the temperature for the

refrigerator drawer to 32°F (0°C) and -3°F (-19°C) for

the freezer drawer for a 24-hour period.

 Press MAX COOL to activate Max Cool feature.

NOTE: The temperature display will remain at -3°F

(-19°C) and the indicator light will remain On for a

24-hour period unless any of the following happens:

 User adjusts any of the compartment

temperatures

 Cool Off Mode is entered (activated by user)

 Sabbath Mode is entered (activated by user)

 After 24 hours, the temperature will automatically

return to the previous temperature set point and

the indicator light will turn Off.

NOTE: If the previous temperature set point was set

to Soft Serve in the freezer drawer, the temperature

will return to the recommended temperature (0°F/-

17°C) instead when Max Cool is complete.

3. Ice Maker and Water Filtration System

(Refrigerator/Freezer Drawers only)

Connect to potable water supply.

IMPORTANT: After connecting the refrigerator to

a water source or replacing the water ﬁlter, ﬁll and

discard three full containers of ice to prepare the

water ﬁlter for use before using ice.

TURNING THE ICE MAKER ONOFF

IMPORTANT: Use the Ice maker touch pad on the

control panel to turn on or off the Ice maker. Do not

adjust the wire arm located on the ice maker.

 Press the ICEMAKER touch pad to turn on the ice

maker. The indicator will illuminate when On.

 Press the ICEMAKER touch pad to turn off the ice

maker.

REMEMBER:

 Allow 24 hours to produce the ﬁrst batch of ice.

 The quality of your ice will only be as good as the

quality of the water supplied to your ice maker.

 Avoid connecting the ice maker to a softened

water supply. Water softener chemicals (such

as salt) can damage parts of the ice maker and

lead to poor quality ice. If a softened water supply

cannot be avoided, make sure the water softener

is operating properly and is well maintained.

 Do not store anything in the ice storage bin.

4. Using Presets

For your convenience, each drawer also has

controls that are preset to recommended storage

temperatures for speciﬁc products.

Pressing any preset option will set the temperature to

the recommended temperature for each category:

Refrigerator Drawers

 Produce: 39°F (3°C)

 Assorted: 37° (2°C)

 Beverage: 34°F (1°C)

 Meat: 32°F (0°C)

Freezer Drawer

 Soft Serve: 6°F (-14°C)

NOTE: Soft Serve is a temporary temperature setting

that will only last for 4 hours and returns to the

previous temperature set point when complete.

 Assorted: 0°F (-17°C)

 Spirits: -2°F (-18°C)

 Deep Freeze: -8°F (-22°C)

5. Adjusting the Temperatures

When the refrigerator drawers are turned On for the

ﬁrst time, a recommended temperature is set by

default. The controls adjust the temperature of both

compartments independently.

 To adjust set point temperatures, press “+” (plus)

or “-” (minus) until the desired temperature

setting is reached.

Model JUDFP242*

NOTE: The set point for the double refrigerator

drawers model is 37°F(2°C). The set point range

for this model is 32°F to 42°F (0°C to 5°C) for both

compartments.

Model JUCFP242*

NOTE: The set point for the refrigerator/freezer

drawers model is 37°F (2°C) for the refrigerator drawer

and 0°F (-17°C) for the freezer drawer. The set point

range for the refrigerator/freezer drawers model is

32°F to 42°F (0°C to 5°C) for the refrigerator drawer

and -8°F to 6°F (-22°C to -14°C) for the freezer drawer.

NOTE: Wait at least 24 hours between adjustments

for the product to acclimate.

6. Viewing Celsius/Fahrenheit

Temperatures

Press the F/C touch pad to toggle between displaying

the temperature in degrees Fahrenheit and degrees

Celsius. The corresponding indicator will illuminate.

7. Sabbath Mode

Sabbath Mode is designed for the traveler or for those

whose religious observances require turning off the

lights. By selecting this feature, the temperature

set points remain unchanged, but the control panel

lights, interior lights, and control audio turn off. For

most efﬁcient refrigerator drawers operation, it is

recommended to exit the Sabbath Mode when it is

no longer required.

 Press and hold SABBATH for 3 seconds to turn on

the feature. After the 3-second countdown, the

feature will activate and all other displays will turn

Off.

 Press and hold SABBATH for 3 seconds to turn off

the feature and turn on the display.

8. Over Temp Alarm

NOTE: If the Over Temp Alarm activates, your food

may spoil. See “Power Interruptions.” Minimize

opening of drawers until temperatures return to

normal.

The Over Temperature feature is designed to let

you know when either the refrigerator drawer

temperature rises above 45°F (7°C) or the freezer

drawer temperature rises above 6°F (-14°C) for 4 hours

or longer. The audio alarm will shut off automatically

when the temperature returns to normal. To let you

know an Over Temperature condition occurred, the

indicator light will continue to ﬂash until the Reset

Alarm touch pad is pressed. If the over temperature

condition is still present when an Over Temp reset

is performed, the indicator light will continue to

reactivate every 4 hours until refrigerator and freezer

temperatures are below 45°F (7°C) and 15°F (-9°C),

respectively.

NOTE: These features will not appear on your control

unless your refrigerator drawer is above preset range

and the alarm requires a reset.

9. Water Filter Indicator / Reset Filter

The water ﬁlter indicator will help you know when to

change your water ﬁlter. The indicator will change

from dark to yellow when it is time to order a new

ﬁlter.

The indicator will then change from yellow to red

when it is time to replace the water ﬁlter.

The disposable water ﬁlter should be replaced at least

every 6 months. After replacing the water ﬁlter, reset

the water ﬁlter indicator.

 Press and hold RESET FILTER for 3 seconds. The

indicator light will turn Off.

NOTE: These features will not appear on your control

unless you need to order or replace your ﬁlter.

NORMAL SOUNDS

Your new refrigerator drawers may make sounds that

your old refrigerator drawers didn’t. Because the sounds

are new to you, you might be concerned about them.

Most of the new sounds are normal. Hard surfaces, such

as the ﬂoor, walls, and cabinets, can make the sounds

seem louder. The following describes the kinds of sounds

and what may be making them.

 Your refrigerator drawers are designed to run more

efﬁciently to keep your food items at the desired

temperatures and to minimize energy usage. The

high efﬁciency compressor and fans may cause your

refrigerator drawers to run longer than your old ones.

You may also hear a pulsating or high-pitched sound

from the compressor or fans adjusting to optimize

performance.

 You may hear the evaporator fan motor circulating air

through the refrigerator drawers. The fan speed may

increase as you open the drawers or add warm food.

 As each cycle ends, you may hear a gurgling sound

due to the refrigerant ﬂowing through the sealed

system tubing.

 Contraction and expansion of the inside walls may

cause a popping noise.

 You may hear air being forced over the condenser by

the condenser fan.

 You may hear water running into the drain pan

during the Off cycle.

ENSURING PROPER AIR CIRCULATION

In order to ensure proper temperatures, you need to

permit airﬂow inside the drawers.

Do not block any airﬂow vents. If the vents are blocked,

airﬂow will be obstructed and temperature and moisture

problems may occur.

IMPORTANT: To avoid odor transfer and drying out of

food, wrap or cover foods tightly.

ICE MAKER

USING THE ICE MAKER WITHOUT THE WATER FILTER

You can run the ice maker without a water ﬁlter. Your

water will not be ﬁltered.

1. Slide the ﬁlter cap off the end of the water ﬁlter. With

the ﬁlter cap in the horizontal position, insert the cap

into the base grille until it stops.

IMPORTANT: Do not discard the cap. It is part of your

refrigerator. Keep the cap to use with a replacement ﬁlter.

CARE AND CLEANING

CLEANING

The drawers defrost automatically. However, clean both

drawers about once a month to avoid buildup of odors.

Wipe up spills immediately.

TO CLEAN YOUR DRAWERS:

1. Unplug drawer or disconnect power.

2. Hand wash, rinse, and dry removable parts and

interior surfaces thoroughly. Use a clean sponge or

soft cloth and a mild detergent in warm water.

 Do not use abrasive or harsh cleaners such as

window sprays, scouring cleansers, ﬂammable

ﬂuids, cleaning waxes, concentrated detergents,

bleaches or cleansers containing petroleum

products on plastic parts, interior and drawer

liners or gaskets. Do not use paper towels,

scouring pads, or other harsh cleaning tools.

These can scratch or damage materials.

 To help remove odors, you can wash interior walls

with a mixture of warm water and baking soda

(2 tbs to 1 qt [26 g to 0.95 L] of water).

3. Wash stainless steel and painted metal exteriors with

a clean sponge or soft cloth and a mild detergent in

warm water. Do not use abrasive or harsh cleaners.

Dry thoroughly with a soft cloth. To avoid damage to

painted metal exteriors, apply appliance wax (or auto

paste wax) with a clean, soft cloth. Do not wax plastic

parts.

NOTE: To keep your Stainless Steel refrigerator

drawers looking like new and to remove minor

scuffs or marks, it is suggested that you use the

manufacturer’s approved Stainless Steel Cleaner and

Polish. To order the cleaner, see “Accessories.”

IMPORTANT:

 This cleaner is for stainless steel parts only!

 Do not allow the Stainless Steel Cleaner and

Polish to come into contact with any plastic parts

such as the trim pieces or drawer gaskets. If

unintended contact does occur, clean plastic part

with a sponge and mild detergent in warm water.

Dry thoroughly with a soft cloth.

CHANGING THE WATER FILTER

The water ﬁlter is located through the base grille. You do

not have to remove the base grille in order to change the

water ﬁlter.

1. Locate the water ﬁlter cap in the front base grille.

Rotate the cap counterclockwise to a vertical position

and pull the cap and water ﬁlter out through the base

grille.

NOTE: There will be water in the ﬁlter. Some spilling may

occur.

2. Remove the ﬁlter cap by sliding it off the end of the

old ﬁlter. The cap will slide to the left or right.

IMPORTANT: Do not discard the cap. It is part of your

refrigerator drawer. Keep the cap to use with the

replacement ﬁlter.

3. Take the new water ﬁlter out of its packaging and

remove the cover from the O-rings.

4. Slide the ﬁlter cap onto the new water ﬁlter. See the

illustration in Step 2.

5. With the ﬁlter cap in the vertical position, insert the

new ﬁlter into the base grille until it stops. Rotate the

cartridge cap clockwise to a horizontal position.

POWER INTERRUPTIONS

If the power will be out for 24 hours or less, keep both

refrigerator drawers closed to help food stay cold.

If the power will be out for more than 24 hours, do one of

the following:

 Place all perishable food in a food locker or cooler

with dry ice.

 If neither a food locker or cooler is available, consume

food if still cold or throw away perishable food at

once.

WARNING

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

VACATION CARE

IF YOU CHOOSE TO TURN THE REFRIGERATOR

DRAWERS OFF BEFORE YOU LEAVE:

1. Remove all food/beverages/ice from the refrigerator

drawers.

2. Turn Off the Control Panel for the Upper and the

Lower drawers. See “Controls.”

3. Clean refrigerator drawers, wipe and dry them well.

4. Tape rubber or wood blocks to the tops of both

drawers to prop them open far enough for air to get

in. This stops odor and mold from building up.

TROUBLESHOOTING

Try the solutions suggested here ﬁrst in order to avoid the cost of an unnecessary service call.

OPERATION

 Power supply cord unplugged? Plug into a

grounded 3 prong outlet.

 Is the refrigerator control set to the Cool Off

setting? See “Controls.”

 Household fuse blown, or a circuit breaker tripped?

Replace the fuse or reset the circuit. If the problem

continues, call an electrician.

 Are the refrigerator drawers not cooling? Turn

them off then on again to reset. See “Controls.” If this

does not correct the problem, call for service.

THE MOTOR SEEMS TO RUN TOO MUCH

 Is the room temperature outside hotter than

normal? The motor will run longer under warm

conditions. At normal room temperatures, expect

your motor to run about 80% of the time. Under

warmer conditions, it will run even more.

 Has a large amount of food just been added to the

refrigerator drawers? Adding a large amount of food

warms the refrigerator drawers. It is normal for the

motor to run longer in order to cool the refrigerator

drawer back down.

 Are the drawers opened often? The motor will run

longer when this occurs. Conserve energy by getting

all items out at one time, keeping food organized, and

closing the drawer as soon as possible.

 Are the controls not set correctly for the

surrounding conditions? Refer “Controls” section.

 Are the drawers not closed completely? Close the

drawers ﬁrmly. If they do not close completely, see

“The drawers will not close completely” later in this

section.

 Are the drawer gaskets not sealed all the way

around? Contact a technician or other qualiﬁed

person.

THE REFRIGERATOR DRAWERS SEEMS TO MAKE TOO

MUCH NOISE

 The sounds may be normal for your refrigerator

drawers. See “Normal Sounds.”

THE DIVIDER BETWEEN THE TWO COMPARTMENTS IS

WARM

The warmth is probably due to normal operation of the

automatic exterior moisture control. If still concerned, call

for service.

TEMPERATURE AND MOISTURE

TEMPERATURE IS TOO WARM

 Are the air vents blocked in either compartment?

This obstructs cold air movement between the

compartments. Remove any objects from in front of

the air vents. See “Ensuring Proper Air Circulation” for

the location of air vents.

 Are the drawers opened often? The refrigerator

drawers will warm when this occurs. Keep the

refrigerator drawers cool by getting all items out at

one time, keeping food organized, and closing the

door as soon as possible.

 Has a large amount of food just been added to the

refrigerator drawers? Adding a large amount of food

warms the refrigerator drawers. It can take several

hours for the refrigerator drawers to return to the

normal temperature.

 Are the controls set correctly for the surrounding

conditions? See “Controls.”

 Are the refrigerator drawers not cooling? Turn

them off then on again to reset. See “Controls.” If this

does not correct the problem, call for service.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

THERE IS INTERIOR MOISTURE BUILDUP

 Are the air vents blocked in the refrigerator

drawers? Remove any objects from in front of the air

vents. See “Ensuring Proper Air Circulation” for the

location of air vents.

 Are the drawers opened often? Avoid humidity

buildup by getting all items out at one time, keeping

food organized, and closing the drawer as soon as

possible.

 Is the room humid? It is normal for moisture to build

up inside the refrigerator drawers when the room air

is humid.

 Is the food packaged correctly? Check that all food

is securely wrapped. Dry damp food containers before

placing in the refrigerator drawers.

 Are the controls set correctly for the surrounding

conditions? See “Controls.”

DRAWERS

THE DRAWERS WILL NOT CLOSE COMPLETELY

Are food packages blocking the drawer open?

Rearrange containers so that they ﬁt more tightly and

take up less space.

THE DRAWERS ARE DIFFICULT TO OPEN

 Is the gasket dirty or sticky? Clean the gasket and

the surface that it touches. Rub a thin coat of parafﬁn

wax on the gasket following cleaning.

WARNING

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

ASSISTANCE

IF YOU NEED SERVICE

Before calling for assistance or service, please check

“Troubleshooting.” It may save you the cost of a service

call. If you still need help, follow the instructions below.

When calling, please know the purchase date and the

complete model and serial number of your appliance.

This information will help us to better respond to your

request. Please refer to the warranty page in this manual

for more information on service.

IF YOU NEED REPLACEMENT PARTS

Component parts should be replaced with like

components and servicing should be done by factory

authorized service personnel, so as to minimize the risk

of possible ignition due to incorrect parts or improper

service.

IN THE U.S.A.

Call the JennAir Customer eXperience Center toll free at

1-800-JENNAIR (1-800-536-6247), or visit our website at

www.jennair.com.

OUR CONSULTANTS PROVIDE ASSISTANCE WITH:

 Features and speciﬁcations on our full line of

appliances.

 Installation information.

 Use and maintenance procedures.

 Accessory and repair parts sales.

 Specialized customer assistance (Spanish speaking,

hearing impaired, limited vision, etc.).

 Referrals to local dealers, repair parts distributors,

and service companies. JennAir designated service

technicians are trained to fulﬁll the product warranty

and provide after warranty service, anywhere in the

United States.

To locate the JennAir designated service company in your

area, you can also look in your telephone directory Yellow

Pages.

FOR FURTHER ASSISTANCE

If you need further assistance, you can write to JennAir

with any questions or concerns at:

JennAir Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your

correspondence.

IN CANADA

Call the JennAir Canada Customer eXperience Centre toll

free: 1-800-JENNAIR (1-800-536-6247).

OUR CONSULTANTS PROVIDE ASSISTANCE WITH:

 Features and speciﬁcations on our full line of

appliances.

 Use and maintenance procedures.

 Accessory and repair parts sales.

 Referrals to local dealers, repair parts distributors,

and services companies. JennAir Canada designated

service technicians are trained to fulﬁll the product

warranty and provide after-warranty service,

anywhere in Canada.

FOR FURTHER ASSISTANCE

If you need further assistance, you can write to JennAir

Canada with any questions or concerns at:

JennAir Canada

Customer eXperience Centre

200 – 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your

correspondence.

ACCESSORIES

To order accessories,

call 1-800-JENNAIR (1-800-536-6247). and ask for the

appropriate part number listed below or contact your

authorized JennAir dealer.

REPLACEMENT WATER FILTER:

Order Part #4396701

AFFRESH

KITCHEN & APPLIANCE CLEANER:

In U.S.A., order part #W10355010

In Canada, order part # W10355010B

AFFRESH

STAINLESS STEEL CLEANER:

In U.S.A., order part #W10355016

In Canada, order part # W10355016B

PRODUCT DATA SHEETS

BASE GRILLE WATER FILTRATION SYSTEM

MODEL WFL200V CAPACITY 200 GALLONS 757 LITERS

MODEL WFNL120V CAPACITY 120 GALLONS 454 LITERS

This system has been tested according to ANSI/NSF 42/53 for the reduction of the substances listed below. The

concentration of the indicated substances in water entering the system was reduced to a concentration less than or

equal to the permissible limit for water leaving the system, as speciﬁed in ANSI/NSF 42/53.

Substance

Reduction Aesthetic

Effects

NSF Reduction

Requirements

Average

Inﬂuent

Challenge

Concentration

Maximum

Efﬂuent

Average

Efﬂuent

Minimum %

Reduction

Average %

Reduction

Chlorine Taste/Odor

Particulate Class III*

≥50%

≥85%

1.9 mg/L

49,333/mL

2.0 mg/L ± 10%

At least 10,000

particles/mL

0.07 mg/L

640 mg/L**

0.06 mg/L

312 mg/L

>75.0%

98.7%

>75.0%

99%

Contaminant

Reduction

NSF Reduction

Requirements

Average

Inﬂuent

Challenge

Concentration

Maximum

Efﬂuent

Average

Efﬂuent

Minimum %

Reduction

Average %

Reduction

Lead: @ pH 6.5

Lead: @ pH 8.5

0.01mg/L

0.14 mg/L***

0.15 mg/L***

0.15 mg/L ± 10%

0.0014 mg/L

0.0069 mg/L

0.0011 mg/L

0.0042 mg/L

99.0%

95.4%

99.21%

97.08%

Mercury: @ pH 6.5

Mercury: @ pH 8.5

0.002 mg/L

0.0059 mg/L

0.0054 mg/L

0.006 mg/L ± 10%

0.0009 mg/L

0.0007 mg/L

0.0004 mg/L

0.00043 mg/L

84.74%

87.03%

92.47%

91.93%

Benzene 0.0050 mg/L 0.0157 mg/L 0.015 ± 10% 0.002 mg/L 0.00083 mg/L 87.26% 94.71%

p-dichlorobenzene 0.075 mg/L 0.210 mg/L 0.225 ± 10% 0.0005 mg/L 0.0005 mg/L 99.76% 99.76%

Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa).

Temp. = 63°F (17.2°C).

 It is essential that operational, maintenance, and

ﬁlterreplacement requirements be carried out for the

product toperform as advertised.

 Model WF-L200V: The ﬁlter monitor system

measures theamount of water that passes

through the ﬁlter and alerts youto replace the

ﬁlter. When 90% of the ﬁlter’s rated life is used,the

ﬁlter indicator light changes from green to yellow.

When100% of the ﬁlter’s rated life is used, the ﬁlter

indicator lightchanges from yellow to red, and it

is recommended that youreplace the ﬁlter. Use

replacement cartridge L200V / NL120V,part #4396702.

2014 suggested retail price of $32.99 U.S.A./$49.99

Canada. Prices are subject to change without notice.

Model WF-NL120V: Change the water ﬁlter cartridge

every6-9 months. Use replacement cartridge L200V

/ NL120V, part#4396702. 2014 suggested retail price

of $32.99 U.S.A./$49.99 Canada. Prices are subject to

change without notice.

 The product is for cold water use only.

 Do not use with water that is microbiologically unsafe

or ofunknown quality without adequate disinfection

before or afterthe system.

 Refer to the front cover or “Accessories” section for

theManufacturer’s name, address and telephone

number.

 Refer to the “Warranty” section for the Manufacturer’s

limitedwarranty.

Application Guidelines/Water Supply Parameters

Water Supply City or Well

Water Pressure 30 - 120 psi (207 - 827 kPa)

Water Temperature 33° - 100°F (0.6° - 37.8° C)

Service Flow Rate 0.5 GPM (1.89 L/min.) @ 60 psi.

(413.7 kPa)

Te sted and certified by NSF International against ANSI/NSF Standard

42 for the reduction of Chlorine, Ta ste and Odor, Particulate Class lll*;

and against ANSI/NSF Standard 53 for the reduction of Lead,

Mercury, Benzene, and p-dichlorobenzene.

*Class III particle size: >5 to <15 um

**Test requirement is at least 10,000 particles/mL of AC Fine Test Dust.

***These contaminants are not necessarily in your water supply. Performance may vary based on local water conditions.

NSF is a registered trademark of NSF International.

La page charge ...

Jenn-Air JUDFP242HL Le manuel du propriétaire

Marque: Jenn-Air

Modèle: JUDFP242HL

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Jenn-Air JUDFP242HL Owner's manual

Jenn-Air JUDFP242HL Le manuel du propriétaire

Ce manuel convient également à

Jenn-Air JUDFP242HL Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents