Zephyr AK9334BS Guide d'installation

WWW.ZEPHYRONLINE.COM

NOV20.0401

Airﬂow Control Technology

TM

C

Monsoon II

AK9334BS, AK9340BS, AK9346BS, AK9352BS

EN Use, Care, and Installation Guide

FR Guide d’utilisation, d’entretien et d’installation

2

Monsoon II Use, Care, and Installation Guide

MONSOON II

INSERT

PRO

3

Monsoon II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Contents

Page

Safety Information ............................................................................ 4-9

Types of Safety Warnings ................................................................... 4

General Safety ..................................................................................5-8

Operation ........................................................................................... 8

Electrical Requirements .....................................................................8-9

Federal Communication Commission Interface Statement ................. 9

List of Materials .................................................................................. 10

Installation Instructions .................................................................... 11-19

Ducting Calculation Sheet ..................................................................11

Mounting Height, Clearance, & Ducting .......................................... 12-13

Ducting Options .................................................................................14

Hood Speciﬁcations ............................................................................15

Electrical Supply .................................................................................16

Cable Lock .........................................................................................16

Preparation & Installation .................................................................17-19

Features & Controls ......................................................................... 20-23

Touch Controls ................................................................................20-21

RF Remote Control ..........................................................................22-23

Maintenance ................................................................................... 24-26

Hood & Filter Cleaning .....................................................................24-25

LumiLight LED ................................................................................... 26

ACT™ Conversion ............................................................................ 27-29

Airﬂow Control Technology (ACT™) ................................................... 27

Enabling ACT™ ................................................................................28-29

Wiring Diagram ..................................................................................30

Troubleshooting................................................................................31-32

List of Parts & Accessories .................................................................. 33

Notes .................................................................................................. 34

Limited Warranty ............................................................................... 35

Product Registration ........................................................................... 36

4

Monsoon II Use, Care, and Installation Guide

MONSOON II

INSERT

PRO

Safety Information

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual for your appliance. Always read

and obey all safety messages.

This is the Safety Alert Symbol. This symbol alerts you to potential hazards that can cause severe

bodily injury or death. All safety messages will follow the Safety Alert Symbol and either the words

“DANGER” “WARNING” or “CAUTION”

DANGER

WARNING

CAUTION

Danger means that failure to heed this safety

statement may result in severe injury or death.

Warning means that failure to heed this safety

statement may result in extensive product damage,

serious personal injury, or death.

Caution means that failure to heed this safety

statement may result in minor or moderate

personal injury, property or equipment damage.

5

Monsoon II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Safety Information

To reduce the risk of ﬁre or electric shock, do not use this fan

with any solid-state control device.

WARNING

READ AND SAVE THESE INSTRUCTIONS

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE

THE FOLLOWING:

a) Use this unit only in the manner intended by the manufacturer. If you have questions, contact the

manufacturer.

b) Before servicing or cleaning unit, switch power o at service panel and lock the service

disconnecting means to prevent power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to

the service panel.

WARNING

General Safety

For General Ventilating Use Only. Do Not Use To Exhaust

Hazardous Or Explosive Materials And Vapors. Take care

when using cleaning agents or detergents. Suitable for use in

household cooking area.

CAUTION

6

Monsoon II Use, Care, and Installation Guide

MONSOON II

INSERT

PRO

Safety Information

READ AND SAVE THESE INSTRUCTIONS

WARNING - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy

spillovers that may ignite. Heat oils slowly on low or medium settings.

b) Always turn hood ON when cooking at high heat or when ﬂambeing food. (i.e. Crepes Suzette,

Cherries Jubilee, Peppercorn Beef Flambe’).

c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or ﬁlter.

d) Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING

WARNING - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING:

a) SMOTHER FLAMES with a close-ﬁtting lid, cookie sheet, or metal tray, then turn o the burner. BE

CAREFUL TO PREVENT BURNS. If the ﬂames do not go out immediately, EVACUATE AND CALL THE

FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN – You may be burned.

c) DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.

d) Use an extinguisher ONLY if:

1) You know you have a Class ABC extinguisher, and you already know how to operate it.

2) The ﬁre is small and contained in the area where it started.

3) The ﬁre department is being called.

4) You can ﬁght the ﬁre with your back to an exit

Based on “Kitchen Firesafety Tips” published by NFPA.

WARNING

7

Monsoon II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Safety Information

READ AND SAVE THESE INSTRUCTIONS

WARNING

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE

THE FOLLOWING:

a) Installation work and electrical wiring must be done by qualiﬁed person(s) in accordance with all

applicable codes and standards, including ﬁre-rated construction.

b) Sucient air is needed for proper combustion and exhausting of gases through the ﬂue (chimney)

of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s

guideline and safety standards such as those published by the National Fire Protection Association

(NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

c) When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden

utilities.

d) Ducted fans must always be vented to the outdoors.

e) If this unit is to be installed over a tub or shower, it must be marked as appropriate for the

application and be connected to a GFCI (Ground Fault Circuit Interrupter) - protected branch circuit.

WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

WARNING

8

Monsoon II Use, Care, and Installation Guide

MONSOON II

INSERT

PRO

Safety Information

READ AND SAVE THESE INSTRUCTIONS

Ź To reduce risk of ﬁre and to properly exhaust air outside, do not vent exhaust air into spaces within

walls, ceilings, attics, crawl spaces, or garages.

CAUTION

Operation

Ź Always leave safety grilles and ﬁlters in place. Without these components, operating blowers could

catch onto hair, ﬁngers and loose clothing.

Ź The manufacturer declines all responsibility in the event of failure to observe the instructions given

here for installation, maintenance and suitable use of the product. The manufacturer further

declines all responsibility for injury due to negligence and the warranty of the unit automatically

expires due to improper maintenance.

NOTE: Please check www.zephyronline.com for revisions before doing any custom work.

Electrical Requirements

Important:

Observe all governing codes and ordinances.

It is the customer’s responsibility to be aware of these below:

Ź To contact a qualiﬁed electrical installer.

Ź To assure that the electrical installation is adequate and in conformance with National Electrical

Code, ANSI/NFPA 70 latest edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1

and C22.2 No.0-M91 - latest edition** and all local codes and ordinances.

Ź If codes permit and a separate ground wire is used, it is recommended that a qualiﬁed electrician

determine that the ground path is adequate.

Ź Do not ground to a gas pipe.

Ź Check with a qualiﬁed electrician if you are not sure the range hood is properly grounded.

Ź Do not have a fuse in the neutral or ground circuit.

9

Monsoon II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Safety Information

READ AND SAVE THESE INSTRUCTIONS

Prop. 65 Warning for California Residents: This product may

contain chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

WARNING

Ź This appliance requires a 120V 60Hz electrical supply and connected to an individual properly

grounded branch circuit protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring

must be 2 wire with ground. Please also refer to Electrical Diagram on product.

Ź A cable locking connector (not supplied) might also be required by local codes. Check with local

requirements, purchase and install appropriate connector if necessary.

* National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269

** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575

Federal Communication Commission Interface Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined

by turning the equipment o and on, the user is encouraged to try to correct the interference by one

of the following measures:

Ź Reorient or relocate the receiving antenna.

Ź Increase the separation between the equipment and receiver.

Ź Connect the equipment into an outlet on a circuit dierent from that to which the receiver is

connected.

Ź Consult the dealer or an experienced radio/TV technician for help.

10

Monsoon II Use, Care, and Installation Guide

MONSOON II

INSERT

PRO

List of Materials

Parts Supplied

Quantity Part

1 Insert hood body

2 Pro bae ﬁlters (AK9334BS & AK9340BS)

3 Pro bae ﬁlters (AK9346BS & AK9352BS)

4 LumiLight LED, 6W (pre-installed)

1 Dual internal blower (pre-installed)

1 10” round duct collar

1 RF remote control (w/ battery & holder)

1 Hardware package

M4 x 6mm (4)

Wire Caps (3)

#8 x 1/2” (12)

RF Remote Control (1) Remote Holder (1)

Parts Not Supplied

Ducting, conduit and all installation tools

Cable locking connector (if required by local codes)

11

Monsoon II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Installation Instructions

Duct pieces

To t al

Equivalent number

length x used =

3- 1/ 4” x 10”

Rect.,

straight

1 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. to

6” round

transition

5 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. to

6” round

transition

90

0

elbow

20 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

90

0

15 Ft.

x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

45

0

9 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

straight

1 Ft. x ( ) =

Ft.

Subtotal column 1 =

Duct pieces

To t al

Equivalent number

length x used =

6”, 7”, 8”, 10”

Round, wall

cap with

damper

30 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round

roof cap

30 Ft. x ( ) =

Ft.

Subtotal column 2 =

Subtotal column 1 =

Total ductwork =

Maximum Duct Length: For satisfactory air movement,

the total duct length

should not exceed 150 equivalent feet.

6” round to

3- 1/ 4” x 10”

rect.

transition

1 Ft. x ( ) =

Ft.

6” round to

3- 1/ 4” x 10”

rect.

transition

90

0

elbow

16 Ft. x ( ) =

Ft.

7” round to

3 1/ 4” x 10”

rect.

transition

8 Ft. x ( ) =

Ft.

7” round to

3- 1/ 4” x 10”

rect.

transition

90

0

elbow

23 Ft. x ( ) =

Ft.

elbow

7” to 6” or

8” to 7” Round

tapered

reducer

25 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 90

0

elbow

15 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 45

0

elbow

9 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 90

0

ﬂat elbow

24 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect.

wall cap

with damper

30 Ft. x ( ) =

Ft.

Ft. x ( ) =

Ft.

15

6”, 7“, 8”

Round

in-line

damper

Ducting Calculation Sheet

12

Monsoon II Use, Care, and Installation Guide

MONSOON II

INSERT

PRO

Installation Instructions

Mounting Height, Clearance, & Ducting

24” min.

36” max.

36”

13

Monsoon II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Installation Instructions

Mounting Height, Clearance, & Ducting

A minimum of 10” round duct must be used to maintain maximum air ﬂow eciency.

Always use rigid type metal ducts only. Flexible ducts could restrict air ﬂow by up to 50%.

Also use calculation (on page 11) to compute total available duct run when using elbows, transitions

and caps.

ALWAYS, when possible, reduce the number or transitions and turns. If long duct run is required,

increase duct size.

If turns or transitions are required; install as far away from hood duct output and as far apart,

between the two as possible.

Minimum mount height between range top to hood bottom should be no less than 24”.

Maximum mount height should be no higher than 36”.

It is important to install the hood at the proper mounting height. Hoods mounted too low could result

in heat damage and ﬁre hazard; while hoods mounted too high will be hard to reach and will lose its

performance and eciency.

If available, also refer range manufacturer’s height clearance requirements and recommended hood

mounting height above range.

For shipment and installation damages:

Ź Please fully inspect unit for damage before installation.

Ź If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or

replacement.

Ź If the unit is damaged by the customer, repair or replacement is the responsibility of the customer.

Ź If the unit is damaged by the installer (if other than the customer), repair of replacement must be

made by arrangement between customer and installer.

14

Monsoon II Use, Care, and Installation Guide

MONSOON II

INSERT

PRO

Installation Instructions

Ducting Options

Ź Use single wall rigid metal ductwork only.

Ź Fasten all connections with sheet metal screws and tape all joints w/ certiﬁed Silver Tape or Duct

Tape.

Fire Hazard: NEVER exhaust air or terminate ductwork into

spaces between walls, crawl spaces, ceilings, attics, or garages.

All exhaust must be ducted to the outside, unless using the

recirculating option.

WARNING

Sot or crawl space

Roof Pitch w/

Flashing & Cap

side wall cap

w/ gravity

damper

side wall cap

w/ gravity damper

15

Monsoon II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Installation Instructions

Ů

Top View

3/4 View

Back View

3”

12

”

2

-1

/

2

”

5-5/8”

(34”) 17-1/4”

(40”) 20-1/4”

(46”) 23-

1/4”

(52”) 26-

1/4”

C/L

Ø

1

0

”

(34”) 12”

(40”) 15”

(46”) 18”

(52”) 21”

2”

elec.

k/o

10-3/8”

(34”) 12”

(40”) 15”

(46”) 18”

(52”) 21”

4-3/8”

elec.

k/o

28-

3/8”

, 34-

3/8

”,

34-

3/8”,

40-

3/8

”,

40-

3/8

”,

46-

1/8”

46-

3/8

”, 52-

3/8

”

C/L

16

Monsoon II Use, Care, and Installation Guide

MONSOON II

INSERT

PRO

Installation Instructions

Electrical Supply

Electrical wiring must be done by qualiﬁed person(s) in

accordance with all applicable codes and standards. Turn o

electrical power at service entrance before wiring.

WARNING

For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not

use extension cord or adapter plug with this appliance.

Follow national electrical codes or prevailing local codes and ordinances.

This appliance requires a 120V 60Hz electrical supply, and connected to an individual, properly

grounded branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring

must be 2 wire w/ ground. Please also refer to the Electrical Diagram labeled on product.

Cable Lock

A cable locking connector (not supplied) might be required by local codes. Check with local

requirements and codes, purchase and install appropriate connector if necessary. (FIG. A)

Cable Lock

FIG. A

17

Monsoon II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Installation Instructions

Preparation & Installation

At least two installers are required due to the

weight and size of the liner.

CAUTION

1. Remove all packing materials and protective

ﬁlm prior to installation. Use caution during

installation to prevent scratches or damage to

the stainless steel.

2. Cut out an opening in the bottom of the

cabinet by following the dimensions in FIG. B.

3. Prepare liner for installation into cabinet by

following the steps on page 18.

4. Lift liner into bottom opening of cabinet and

secure to interior of cabinet using (8) #8 x 1/2”

stainless steel screws; (4) screws in the front

and (4) screws in the sides. FIG. C.

34-1/2” or 40-1/2” or 46-1/2” or 52-1/2”

2

-

5/

8

”

cut o

u

t

(AK9334)

(AK9

340)

(AK9

352

)

(AK9

346)

1/4”

1-1/8”

Make sure the surface you are securing the liner

to is capable of holding the weight of AK93.

Failure to do so may cause personal injury or

damage to cooking surface or counter.

WARNING

FIG. B

FIG. C

5. Finalize installation of electrical and duct work. Seal duct work with certiﬁed aluminum duct tape.

Power on liner, check for leaks around duct tape and verify proper operation.

NOTE: If access to top of liner is not available after installation, electrical and duct work connection

may need to be made prior to installing the liner.

6. Re-install the previously removed bottom panel, side spacer panels (if applicable), grease tray,

and bae ﬁlters.

18

Monsoon II Use, Care, and Installation Guide

MONSOON II

INSERT

PRO

Installation Instructions

Preparation & Installation

1. Remove bae ﬁlters by: 1) Pulling

ﬁlter toward front of liner. 2)

Pivoting rear of ﬁlter down.

2. Remove grease tray by: 1) Pulling

up on tray to release from bottom

panel. 2) Lifting tray out of liner

body.

3. Remove left and right side-spacer

panels by removing (2) screws

from behind each panel.

1

2

1

2

19

Monsoon II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Installation Instructions

Preparation & Installation

Locking Tabs

Bottom Panel Screws

2

1

4. Remove bottom panel by: 1)

Removing (2) screws from left and

right sides of bottom panel. 2)

Pulling bottom panel toward front

of liner to release from locking

tabs.

6. Vertical ducting preparation is

complete. Refer to page 18, step

4 to complete installation.

5. Secure 10” round ducting collar

to top of insert by (4) M4 x 6mm

screws.

20

Monsoon II Use, Care, and Installation Guide

MONSOON II

INSERT

PRO

Features & Controls

1. Blower On/O

By pressing the blower is switched on and o. When switched on, the blower starts up on speed level 1.

ACT Veriﬁcation

- Airﬂow Control Technology (ACT) allows the installer to set the maximum blower CFM to align with local

codes and regulations.

- To verify the maximum blower CFM:

- With hood o, hold the button for 3-4 seconds. If number 6 displays = default max. CFM, if

number 3 displays = max. 590 CFM, and if number 2 displays = max. 390 CFM.

2. Speed Selection

- Press to decrease fan speed. 6, 5, 4, 3, 2, 1.

- If fan is on Speed 1 and is pressed, the fan will power o.

- Press to increase fan speed. Fan On, 1, 2, 3, 4, 5, 6.

- If hood is o and is pressed, the fan will turn on speed 1.

ACT Enabled Speed Selections

- When ACT is enabled, the number of blower speeds will be reduced as follows:

- 590 CFM = Maximum 3 speeds

- 390 CFM = Maximum 2 speeds

3. Delay O

This feature is used for programmed shut down of blower 5 minutes after the function is activated. Press

once, a dot ﬂashes in the lower right side of display indicating the function is on. The blower will

completely shut down after 5 minutes.

4. Lights Low/High/O

Switch lights on to low by pressing once, press a second time for high and again to shut o lights.

5. Display Window

The display window indicates speed levels and features such as bae ﬁlter clean reminder, delay o and

clean air indicator.

Lights Low/High/O

5 Min Delay O

Display (speed level, delay o, ﬁlter clean)

Adjust 6 Speed Levels

Blower On/O

1

2

3

4

5

Touch Controls

La page charge ...

Zephyr AK9334BS Guide d'installation

Zephyr AK9334BS Guide d'installation

dans d''autres langues

Documents connexes

Autres documents