Monogram ZV855SPSS Guide d'installation

Installation

Instructions

Island Vent Hood

ZV850, ZV855

Hotte Aspirante Îlot

Instructions d’installation

La section française commence à la page 22

Campana de ventilación en isla

Instrucciones de instalación

La sección en español empieza en la página 43

2

Safety Information

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT³Save these instructions for

local inspector’s use.

•

IMPORTANT³Observe all governing codes

and ordinances.

• Note to Installer³ Be sure to leave these

instructions with the Consumer.

• Note to Consumer³ Keep these instructions

with your Owner’s Manual for future reference.

• Skill Level³Installation of this appliance requires

basic mechanical and electrical skills.

• Completion Time³WR+RXUV

• Proper installation is the responsibility of the installer.

Product failure due to improper installation is not

covered under the warranty.

)RU0RQRJUDPORFDOVHUYLFHLQ\RXUDUHDFDOO

)RU0RQRJUDPVHUYLFHLQ&DQDGDFDOO

)RU0RQRJUDP3DUWVDQG$FFHVVRULHVFDOO

CAUTION:

Due to the weight and size of these vent hoods and

to reduce the risk of personal injury or damage to the

product, TWO PEOPLE ARE REQUIRED FOR PROPER

INSTALLATION.

WARNING:

To reduce the risk of fire or electrical shock, do not

use this range hood with any external solid-state speed

control device. Any such alteration from original factory

wiring could result in damage to the unit and/or create

an electrical safety hazard.

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

WARNING: TO REDUCE THE RISK OF

FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

A. Use this unit only in the manner intended

by the manufacturer. If you have any questions,

contact the manufacturer.

B. Before servicing or cleaning the unit, switch

the power off at the service panel and lock the

service disconnecting means to prevent the power

from being switched on accidentally. When the

service disconnecting means cannot be locked,

securely fasten a prominent warning device,

such as a tag, to the service panel.

CAUTION: FOR GENERAL VENTILATING

USE ONLY. DO NOT USE TO EXHAUST HAZARDOUS

MATERIALS, EXPLOSIVE MATERIALS OR VAPORS.

WARNING: TO REDUCE THE RISK OF

FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

• Installation work and electrical wiring must be done

by qualified person(s) in accordance with all applicable

codes and standards, including fire-rated construction.

• Sufficient air is needed for proper combustion

and exhausting of gases through the flue (chimney)

of fuel burning equipment to prevent back-drafting.

Follow the heating equipment manufacturer’s

guidelines and safety standards, such as those

published by the National Fire Protection Association

(NFPA), the American Society for Heating, Refrigeration

and Air Conditioning Engineers (ASHRAE) and the local

code authorities. When applicable, install any makeup

(replacement) air system in accordance with local

building code requirements.

Visit GEAppliances.com

for available makeup air solutions.

• When cutting or drilling into walls or ceilings, do not

damage electrical wiring and other hidden utilities.

• Ducted systems must always be vented

to the outdoors.

• Local codes vary. Installation of electrical connections

and grounding must comply with applicable codes.

In the absence of local codes, the vent should be

installed in accordance with National Electrical Code

ANSI/NFPA 70-1990 or latest edition.

CAUTION: To reduce risk of fire and to

SURSHUO\H[KDXVWDLUEHVXUHWRGXFWDLURXWVLGH³GRQRW

vent exhaust air into spaces within walls or ceilings or

into attics, crawl spaces or garages.

READ AND SAVE THESE INSTRUCTIONS

Design Information

MODELS AVAILABLE

Model ZV850

Model ZV855

These hoods may be installed to vent to the outdoors,

or they may be installed for recirculating operation.

All necessary parts for recirculating operation are

supplied with the hood. No kits required.

• These vent hoods can be installed over any 30

”

or 36

”

Monogram electric or gas cooktop except Monogram

Professional cooktops or ranges larger than 30”.

• Reversible duct covers accommodate recirculating

operation.

• The telescopic duct covers conceal the ductwork

running from the top of the hood to the ceiling.

• The supplied duct cover is sized to reach ceiling heights

over 8 feet. See the table on page 8.

PRODUCT DIMENSIONS AND CLEARANCES

The vent hood must be installed 24” minimum and

30

” maximum above the cooking surface.

NOTE: Installation height should be measured from

the cooking surface to the lowest part of the hood.

=;6366'XFW&RYHU$FFHVVRU\

This accessory is available for installation with ceiling

heights

of

8

Ļ

7

”

to over 10 feet.

See the table on page 8.

The duct cover accessory must be on-site with the

hood at the time of installation.

24” Minimum

30” Maximum

36" Minimum

*Height

to Ceiling

8-1/4"

27-1/2”

35-3/8ļ (excluding utensil rods)

36-1/2ļ (including utensil rods)

CONTENTS

Design Information

Models Available ................................................................................ 3

Product Dimensions ......................................................................... 3

Advance Planning

Ductwork Planning .......................................................................... 4

Ceiling Framing for Adequate Support .................................. 4

Installation Preparation

Duct Fittings ......................................................................................... 5

Power Supply ...................................................................................... 6

Tools and Materials Required ...................................................... 6

Remove the Packaging ................................................................. 7

Check Installation Hardware ...................................................... 7

Determine Installation Height ..................................................... 8

Install Ceiling Support Structure .........................................9–11

Installation Instructions

Installation – Vented to the Outside ...............................12–16

Step 1, Mount Template ...............................................................12

Step 2, Install Upper Support Frame ......................................12

Step 3, Install Lower Support Frame ......................................12

Step 4, Secure Wiring ....................................................................13

Step 5, Size and Install Ductwork ............................................13

Step 6, Install Decorative Duct Covers ..................................14

Step 7, Install Hood ........................................................................15

Step 8, Connect Electrical ............................................................15

Step 9, Slide Duct Cover

Down, Install Side Utensil Rods ................................................15

Step 10, Install Filters.....................................................................16

Step 11, Finalize Installation.......................................................16

Installation Instructions

Installation – Recirculating .................................................17–21

Step 1, Mount Template ...............................................................17

Step 2, Install Upper Support Frame ......................................17

Step 3, Install Lower Support Frame ......................................18

Step 4, Secure Wiring ....................................................................18

Step 5, Size and Install Ductwork ............................................18

Step 6, Install Decorative Duct Covers ..................................19

Step 7, Install Hood ........................................................................20

Step 8, Connect Electrical ............................................................20

Step 9, Slide Duct Cover

Down, Install Side Utensil Rods ................................................20

Step 10, Install Filters.....................................................................21

Step 11, Finalize Installation.......................................................21

3

Advance Planning

DUCTWORK PLANNING

• The hood is designed to be vented vertically

through the ceiling. Use locally supplied elbows

to vent horizontally through the rear wall.

• Determine the exact location of the vent hood.

• Plan the route for venting exhaust to the outdoors.

• Use the shortest and straightest duct route

possible. For satisfactory performance, duct run

should not exceed 100Ļ equivalent length for any

duct configurations.

• Refer to “Duct Fittings” chart to compute the

maximum permissible length for duct runs to

the outdoors.

• Use rigid metal ductwork only.

• This vent hood must use 6” round duct. The

6” round duct can transition to 3-1/4” x 10”

or3-1/4”x 12”.

• Install the house duct to run horizontally between

ceiling joists or straight up through the roof.

• Install a wall or roof cap with damper at the

exterior opening. Order the wall or roof cap

and any transition and length of duct needed

in advance.

•

When applicable, install any makeup (replacement)

air system in accordance with local building code

requirements.

Visit GEAppliances.com for available

makeup air solutions.

WARNING: TO REDUCE THE RISK

OF FIRE, USE ONLY RIGID METAL DUCTWORK.

CEILING FRAMING FOR ADEQUATE

SUPPORT

• These vent hoods are heavy. Adequate structural

support must be provided. The ceiling structure

must be capable of supporting the weight of the

hood and any inadvertent user contact loads

(approximately 200 pounds). The hood support

frame will be supported by 2 x 4 minimum cross-

framing.

• Installation will be easier if the vent hood is

installed before the cooktop or countertop below

is installed.

4

Accessory Duct Cover

A duct cover accessory may be required for your

installation, depending on ceiling height.

5

DUCT FITTINGS

This Hood Must Use an

” Round Duct. It Can

7UDQVLWLRQWR”[”

RU”[” Duct.

Use this chart to compute

maximum permissible lengths

for duct runs to outdoors.

NOTE: Do not exceed maximum

permissible equivalent lengths!

Maximum duct length:

100 foot for range hoods.

Flexible ducting:

If flexible metal ducting is used,

all the equivalent feet values in

the table should be doubled.

The flexible metal duct should

be straight and smooth and

extended as much as possible.

DO NOT use flexible plastic

ducting.

NOTE: Any home ventilation

system, such as a ventilation

hood, may interrupt the proper

flow of combustion air and

exhaust required by fireplaces, gas

furnaces, gas water heaters and

other naturally vented systems.

To minimize the chance of

interruption of such naturally

vented systems, follow the

heating equipment manufacturer’s

guidelines and safety standards

such as those published by NFPA

and ASHRAE. When applicable,

install any makeup (replacement)

air system in accordance with

local building code requirements.

Visit GEAppliances.com for available

makeup air solutions.

Installation Preparation

Total Duct Run

* Actual length of straight duct plus duct fitting

equivalent. Equivalent length of duct pieces are

based on actual tests conducted by GE Evaluation

Engineering and reflect requirements for good

venting performance with any ventilation hood.

Total

Equivalent Quantity Equivalent

Duct Piece Dimensions Length* Used Length

Round, 1 ft. (per

straight foot length)

3-1/4” x 10” 1 ft. (per

straight foot length)

90° elbow 12 ft.

45° elbow 7 ft.

3-1/4” x 10” 14 ft.

3-1/4” x 12” 10 ft.

90° elbow

3-1/4” x 10” 8 ft.

3-1/4” x 12” 6 ft.

45° elbow

3-1/4” x 10” 33 ft.

3-1/4” x 12” 24 ft.

90° flat elbow

6” round to 2 ft.

rectangular

Rectangular to 8” 2 ft.

round

3-1/4” x 10” 4 ft.

3-1/4” x 12” 4 ft.

 6” round to rectangular

transition 90° elbow

3-1/4” x 10” 4 ft.

3-1/4” x 12” 4 ft.

Rectangular to 6”round

transition 90° elbow

Round wall cap 24 ft.

with damper

3-1/4” x 10” 24 ft.

3-1/4” x 12” 18 ft.

Rectangular wall cap

with damper

Round roof cap 33 ft.

Masking

tape

Gloves

Utility knife

6

POWER SUPPLY

IMPORTANT – (Please read carefully)

WARNING:

FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE

PROPERLY GROUNDED.

Remove house fuse or open circuit breaker before

beginning installation.

Do not use an extension cord or adapter plug with

this appliance. Follow National Electrical Code or

prevailing local codes and ordinances.

Electrical supply

This vent hood must be supplied with 120V, 60Hz,

and connected to an individual, properly grounded

branch circuit, and protected by a 15- or 20-amp

circuit breaker or time-delay fuse.

• Wiring must be 2-wire with ground.

• If the electrical supply does not meet the above

requirements, call a licensed electrician before

proceeding.

• Route house wiring as close to the installation

location as possible. Route additional length from

ceiling joists to reach the junction box on the

hood.

• Connect the wiring to the house wiring in

accordance with local codes.

Grounding instructions

The grounding conductor must be connected to

a ground metal, permanent wiring system, or an

equipment-grounding terminal or lead on the hood.

WARNING: The improper connection

of the equipment-grounding conductor can result

in a risk of electric shock. Check with a qualified

electrician or service representative if you are in

doubt whether the appliance is properly grounded.

TOOLS AND MATERIALS REQUIRED

(NOT SUPPLIED)

Pliers

Wire cutter/stripper

Metal snips

Spirit level

Aluminized

duct tape

Safety glasses

120V, 60Hz. 15- or 20-Amp,

2-wire with ground, properly

grounded branch circuit

Stepladder

Saber saw or keyhole saw

Phillips screwdriver

Strain relief for

junction box

6” round metal

duct, length to

suit installation

Hammer

Flashlight

UL-listed wire nuts

Pencil and tape measure

Installation Preparation

Electric drill with 5/32” bits,

#2 Phillips and 7/16” socket

10 mm wrench

Plumb

REMOVE THE PACKAGING

CAUTION: Wear gloves to protect

against sharp edges.

The vent hood is packed with the duct cover and

support frames.

• Remove the hood, parts and packaging.

• Remove junction box cover.

• Install strain relief onto junction box cover

(not supplied).

NOTE: Additional tools, materials and hardware are

required to construct your ceiling support.

Check Installation Hardware

Locate the hardware accessory bag packed with the

hood and check contents.

Front of Hood

Template

4 Hex-head

wood lag

screws

(6 mm x

2-1/2” or 1/4

x 2-1/2”)

2 Stop screws

(One is in the service

manual envelope.

Leave that screw in

the envelope.)

4 Flat

washers

3 Stainless

steel grease filters

Decorative

duct covers

2 Phillips-head

duct cover

screws

2 Utensil rods with 4 machine screws

7

Installation Preparation

4 (10 mm) Nuts

and lock

washers

Support

frames with 8

screws and 8

washers

8 Frame

attachment

screws with

washers (attached

to accessory

support frames)

Mounting screw holes

Additional Parts for Recirculating Operation

3 Charcoal filters

Air deflector with upper

duct connector and 4

small flat-head screws

Installation Preparation

DETERMINE INSTALLATION HEIGHT

• Telescopic duct covers are provided to conceal

the ductwork running to the ceiling.

• This hood can be installed for vented or

recirculating operation. All necessary parts are

shipped with the hood.

NOTE: Installation height should be measured from

the cooking surface to the bottom of the hood.

The vent hood must be installed 24” min. and

30” max. above the cooking surface. The hood

installation height, from the cooking surface to the

bottom of the hood, depends upon ceiling height

and duct cover limitations.

24” Minimum

30” Maximum

36" Minimum

DUCT COVER DIMENSIONS

=;6366'XFW&RYHU$FFHVVRU\

The accessory is available for installation with ceiling

heights

of

8

Ļ

7”

to

over 10 feet. This accessory

consists of two 26-1/4” duct covers and one 31”

upper support frame piece.

*Possible *Possible

VENTED RECIRCULATING

Ceiling Installation Installation

Height Height Height

7 Ļ11” 24” 24”

8Ļ 24” to 25” 24” to 25”

8Ļ 1” 24” to 26” 24” to 26”

8Ļ 2” 25” to 27” 24” to 27”

8Ļ3” 26” to 28” 24” to 28”

8Ļ 4” 27” to 29” 24” to 29”

8Ļ 5” 28” to 30” 24” to 30”

8Ļ 6” 29” to 30” 25” to 30”

8Ļ 7” 30” 26” to 30”

8Ļ 8” 27” to 30”

8Ļ 9” 28” to 30”

8 Ļ 10” 29” to 30”

8 Ļ 11” 30”

8Ļ 7” 24” 24”

8Ļ 8” 24” to 25” 24” to 25”

8Ļ 9” 24” to 26” 24” to 26”

8 Ļ 10” 24” to 27” 24” to 27”

8 Ļ 11” 24” to 28” 24” to 28”

9Ļ 24” to 29” 24” to 29”

9Ļ 1” 24” to 30” 24” to 30”

9Ļ 2” 24” to 30” 24” to 30”

9Ļ 3” 24” to 30” 24” to 30”

9Ļ 4” 24” to 30” 24” to 30”

9Ļ 5” 24” to 30” 24” to 30”

9Ļ 6” 24” to 30” 24” to 30”

9Ļ 7” 24” to 30” 24” to 30”

9Ļ 8” 25” to 30” 24” to 30”

9Ļ 9” 26” to 30” 24” to 30”

9 Ļ 10” 27” to 30” 24” to 30”

9 Ļ 11” 28” to 30” 25” to 30”

10Ļ 29” to 30” 26” to 30”

10Ļ 1” 30” 27” to 30”

10Ļ 2” 28” to 30”

10Ļ 3” 29” to 30”

10Ļ 4” 30”

*Based on 36” countertop height.

8

ACCESSORY ZX90010 Lower Duct 26.25

”

      Upper Duct 26.25”

ZX8510SPSS – ACCESSORY DUCT COVERS

ACCESSORY ZX90010

Upper Frame 31”



      Supplied Lower Frame

ZX8510SPSS – ACCESSORY UPPER FRAME

Lower Duct 18

”

  Upper Duct 18”

Lower Frame 20.75

”

  Upper Frame 20.75”

ZV850/ZV855

Installation Heights

9-7/16”

15-3/4”

SUPPLIED FRAME

SUPPLIED DUCT COVERS

9

Installation Preparation

Plan the Location of the Hood and Ductwork

• Use a plumb bob to check the location.

The countertop/cooktop below the hood

must be centered with the hood.

• The hood should extend beyond the front and rear

edge of the cooking appliance.

• The duct in the ceiling must be centered over

the cooktop.

CONSTRUCT CEILING SUPPORT

Top view – ceiling joists parallel to front of hood

16” Joist

spacing

8-3/4”

6” Duct

Front

of

hood

2x4 Cross-framing

wood supports

Cooktop

outline

Align duct

to center

of cooktop

Ceiling Support Structure

• At the hood location, install cross-framing between

ceiling joists as shown. (2x4 wood supports

are required to support the weight of the hood.)

• Arrange cross-framing in the ceiling to suit

the existing structure.

• Your ceiling joists will be like one of the following

examples.

EXAMPLE A

Align with

center of

cooktop

Install cross-framing symmetrically

over duct/cooktop centerline

7-5/8”

Top view – ceiling joists run perpendicular to front of hood

Top view – ceiling joists at angle to front of hood

CONSTRUCT CEILING SUPPORT (Continued)

16”

Joist

spacing

8-3/4”

6

”

Duct

Front

of

hood

2x4 Cross-

framing wood

supports

Cooktop

outline

Align duct

to center

of cooktop

16

”

Joist

spacing

6

”

Duct

Cooktop

outline

Align duct

to center

of cooktop

EXAMPLE B

EXAMPLE C

Front

of hood

7-5/8”

2x4 Cross-

framing wood

supports

Install cross-framing symmetrically

over duct/cooktop centerline

7-5/8”

10

Installation Preparation

8-3/4”

Install cross-framing

symmetrically over

duct/cooktop centerline

11

Installation Preparation

CONSTRUCT CEILING SUPPORT (Continued)

Ductwork for Installations Vented to the Outdoors

• Use the shortest and straightest duct route possible.

For satisfactory performance, duct run should not

exceed 100 feet equivalent length for any duct

configuration.

• Refer to “Duct Fittings” chart to compute the

maximum permissible length for duct runs to the

outdoors.

• This vent hood must use 6” round rigid duct.

WARNING: TO REDUCE THE RISK

OF FIRE, USE ONLY RIGID METAL DUCTWORK.

• Install the house ductwork to run horizontally

between ceiling joists or straight up through the

roof.

Finish the Ceiling

• Finish the ceiling surface. Be sure to mark location

of the ceiling joists and cross framing. Check to be

sure the ceiling is level; use shims if necessary.

• Secure each 2 x 4 block with at least four (4), #10

wood screws, 3” long (not supplied). Use 8 wood

screws total for the two supports.

• The cross framing must be accurately aligned

to assure correct positioning of the hood.

• The cross framing must be level in all directions.

Check with a spirit level and adjust if necessary.

IMPORTANT: The ceiling structure must be capable

of supporting the weight of the hood (approximately

200 pounds) and any inadvertent user contact loads.

The hood support frame will be supported by the

2 x 4 cross framing.

6”

Duct

Ceiling joist

2 x 4

Vent straight up

through the ceiling

12

Installation Instructions

INSTALLATION – VENTED TO THE OUTSIDE



INSTALL UPPER SUPPORT FRAME

• Secure the upper support frame to the ceiling

joists and/or cross framing with the 4 screws

provided. For maximum rigidity and strength, the

screws must be driven into the center of the joists

and/or cross-framing.

• Check to be sure the support frame is level,

vertically and horizontally.



INSTALL LOWER SUPPORT FRAME

• Insert lower support frame into the upper support

frame and loosely secure with 8 screws and

washers (4 on the front and 4 on the back sides).

• Adjust the lower support frame up or down

to the desired height above the countertop.

Tighten screws.

IMPORTANT: Again, check to be sure the support is

level in both directions. There is no way to level the

hood after the hood is secured to the frame.



MOUNT TEMPLATE

• Align the template with the marks on the ceiling and

tape in place.

– Be sure the template is oriented correctly, with the

front of the hood.

•

Use a plumb to be sure the mounting holes will provide

parallel alignment with the countertop below.

• Center punch all hole locations.

• Drill pilot holes in the 4 screw

locations. Use a 5/32” bit and drill

approximately 1-1/2” deep.

• Cut wire access hole approximately

1” dia.

• Cut the 6-1/2” duct opening

through the ceiling.

13-5/8

”

24” Minimum

30” Maximum

Wire Access Hole

Front of Hood

13

Installation Instructions

INSTALLATION – VENTED TO THE OUTSIDE



SECURE WIRING

• Route house wiring through the ceiling hole and

pull a length to reach the hood junction box.

• Tape the wire to the front of the frame support to

prevent damage during installation and service.

Ceiling

Support

Frames

Tape

House

Wiring

Front Side



SIZE AND INSTALL DUCTWORK

• Measure from house duct (Dim. A) to bottom of

support frame.

– Add at least 1” for duct overlap at the top.

– Subtract 3/4” for hood insertion into the bottom

of the frame.

• Cut the 6” dia. duct to the required length.

NOTE: The bottom end of the duct must be flared

slightly, to facilitate installation of the hood.

• Install duct up through support frames onto the

house duct. Push duct up until it is 3/4” from the

bottom of the support frame flange.

• Secure the duct to house duct connection with

screws and seal with duct tape.

• Seal duct connection with duct tape, making sure

connection is secured in place.

14

Installation Instructions

INSTALLATION – VENTED TO THE OUTSIDE



INSTALL DECORATIVE DUCT COVERS

• Pretap or drive decorative screw into the screw holes

on the support frame. This will make screw installation

easier.

• Separate the two decorative duct covers.

• Select the inside or top cover with the vent hole

pattern on one end.

For this vented installation to the outside, the hole

pattern should be located at the bottom.

• Locate the 2 supplied duct cover screws.

• Slide the decorative duct cover over the support frame

and push to the ceiling.

• Attach the inside duct cover to the hood support at

the top with 2 supplied duct cover screws.

• Locate the stop screw in the hardware bag

.

• Install the stop screw into one of the two holes and

tighten against the frame to allow the second duct

cover to slide up and pass over.

• Slide the lower duct cover over the installed upper

duct cover and push up past the stop screw location.

• Back out the stop screw far enough to support the

bottom duct cover and prevent it from sliding down

onto the top of the hood.

CAUTION: The stop screw must be

installed. Failure to do so could result in personal

injury or damage to the duct cover.

15

 CONNECT ELECTRICAL

Verify that power is turned off at the source.

WARNING: If house wiring is not 2-wire

with a ground wire, a ground must be provided

by the installer. When house wiring is aluminum,

be sure to use U.L.-approved antioxidant compound

and aluminum-to-copper connectors.

• Install strain relief onto the knockout of the junction

box cover.

• Insert house wiring through strain relief and tighten.

• Connect white leads to branch circuit white lead.

• Connect black leads to branch circuit black lead.

• Connect green/yellow leads to branch circuit green

or bare ground lead.

• Secure all connections with wire nuts on each

electrical connector.

• Push wires into junction box and replace cover.

Be sure wires are not pinched.

Installation Instructions

INSTALLATION – VENTED TO THE OUTSIDE

7

INSTALL HOOD

NOTE: TWO PEOPLE ARE REQUIRED TO COMPLETE

THIS INSTALLATION!

• Lift the hood up to the support frame. Carefully align

the hood mounting studs into the support frame holes,

and at the same time, guide the hood duct connector

into the duct.

• Install 4 nuts and lock washers. Tighten with a 10 mm

wrench.

• Check hood level in both directions.

• Seal the duct connection with duct tape.

NOTE: Do not drive screws through this duct

connection. Doing so will prevent proper damper

operation.

9

SLIDE DUCT COVER DOWN,

INSTALL SIDE UTENSIL RODS

• Slide the lower duct cover up and above the

stop screw.

• Drive the stop screw in close to the frame.

• Slide the lower duct cover down against the top

of the hood. The duct cover should be seated into

the pocket on top of the hood.

• Install the side utensil rods with screws as shown.

16



INSTALL FILTERS

• Remove protective film on filters.

• Tip the filter into the lower channel at the rear

of the opening. Push back, lift and pull the knob

forward until the filter rests on the channel.

• Install all three metal grease filters.

•

Turn power on. If the filter light on the control panel

glows, adjust the right-side filter in the channel to

engage the switch arm.

Lower Filter

Channels



FINALIZE INSTALLATION

• Remove the protective film covering the control panel

on the front face of the hood and any other packaging

materials.

• Make sure the filters are seated properly when

installed and the filter light is not on.

• Be sure fan and lights operate correctly. Refer to

the Owner’s Manual for operating instructions

and the Problem Solver.

Installation Instructions

INSTALLATION – VENTED TO THE OUTSIDE

Lower

filter channel

Installation Instructions

INSTALLATION – RECIRCULATING



INSTALL AIR DEFLECTOR AND

UPPER SUPPORT FRAME

The duct connector is shipped inside the deflector.

• Snap the plastic connector out of

the deflector and remove. Turn it

over. From the bottom, snap the

connector over the opening.

• Slide the assembled deflector into

the upper support frame and secure

with 4 small screws.

• Secure the upper support frame to

the ceiling joists and/or cross framing

with the 4 screws provided. For maximum rigidity

and strength, the screws must be driven into the center

of the joists and/or cross framing.

• Check to be sure the support frame is level, vertically

and horizontally.



MOUNT TEMPLATE

• Align the template with the marks on the ceiling and

tape in place.

– Be sure the template is oriented correctly, with the

front of the hood.

•

Use a plumb to be sure the mounting

holes will provide parallel alignment

with the countertop below.

• Center punch all hole locations.

• Drill pilot holes in the 4 screw

locations. Use a 5/32” bit and drill

approximately 1-1/2” deep.

• Cut wire access hole approximately

1” dia.

17

NOTE: Be sure plastic

connector is installed

on the bottom of the

deflector as shown.

Wire Access Hole

Front of Hood

18

Installation Instructions

INSTALLATION – RECIRCULATING



SECURE WIRING

• Route house wiring through the ceiling hole

and pull a length to reach the hood junction box.

• Tape the wire to the front of the frame support to

prevent damage during installation and service.

Ceiling

Support

Frames

Tape

House

Wiring

Front Side



SIZE AND INSTALL DUCTWORK

• Measure from top duct connector (Dim. A)

to bottom of support frame.

– Subtract 3/4” for hood insertion into the bottom

of the frame.

• Cut the 6” dia. duct to the required length.

NOTE: The bottom end of the duct must be flared

slightly, to facilitate installation of the hood.

• Install duct up through support frames onto the

duct connector. Push duct up until it is 3/4” from

the bottom of the support frame flange. See

illustration.

• Seal duct connection with duct tape, making sure

the connection is secured in place.



INSTALL LOWER SUPPORT FRAME

• Insert lower support frame into the upper support

frame and loosely secure with 8 screws and

washers (4 on the front and 4 on the back sides).

• Adjust the lower support frame up or down

to the desired height above the countertop.

Tighten screws.

IMPORTANT: Again, check to be sure the support is

level in both directions. There is no way to level the

hood after the hood is secured to the frame.

13-5/8

”

19

Installation Instructions

INSTALLATION – RECIRCULATING



INSTALL DECORATIVE DUCT COVERS

• Pretap or drive decorative screw into the screw holes

on the support frame. This will make screw installation

easier.

• Separate the two decorative duct covers.

• Select the inside or top cover with the vent hole

pattern on one end.

For this recirculating installation, the hole pattern

should be located at the top.

• Locate the 2 supplied duct cover screws.

• Slide the decorative duct cover over the support frame

and push to the ceiling.

• Attach the inside duct cover to the hood support at

the top with 2 supplied duct cover screws.

• Locate the stop screw in the hardware bag

.

• Install the stop screw into one of the two holes and

tighten against the frame to allow the second duct

cover to slide up and pass over.

• Slide the lower duct cover over the installed upper

duct cover and push up past the stop screw location.

• Back out the stop screw far enough to support the

bottom duct cover and prevent it from sliding down

onto the top of the hood.

CAUTION: The stop screw must be

installed. Failure to do so could result in personal

injury or damage to the duct cover.

Installation Instructions

INSTALLATION – RECIRCULATING

 CONNECT ELECTRICAL

Verify that power is turned off at the source.

WARNING: If house wiring is not 2-wire

with a ground wire, a ground must be provided

by the installer. When house wiring is aluminum,

be sure to use U.L.-approved antioxidant compound

and aluminum-to-copper connectors.

• Install strain relief onto the knockout of the junction

box cover.

• Insert house wiring through strain relief and tighten.

• Connect white leads to branch circuit white lead.

• Connect black leads to branch circuit black lead.

• Connect green/yellow leads to branch circuit green

or bare ground lead.

• Secure all connections with wire nuts on each

electrical connector.

• Push wires into junction box and replace cover.

Be sure wires are not pinched.

7

INSTALL HOOD

NOTE: Before installing the hood, the metal damper

flaps on top of the hood exhaust outlet may be removed.

Do not remove the duct transition. The damper is not

required for this recirculating operation.

NOTE: TWO PEOPLE ARE REQUIRED TO COMPLETE

THIS INSTALLATION!

• Lift the hood up to the support frame. Carefully align

the hood mounting studs into the support frame holes,

and at the same time, guide the hood duct connector

into the duct.

• Install 4 nuts and lock washers. Tighten with a 10 mm

wrench.

• Check hood level in both directions.

• Seal the duct connection with duct tape.

NOTE: Do not drive screws through this duct

connection. Doing so will prevent proper damper

operation (if present).

9

SLIDE DUCT COVER DOWN,

INSTALL SIDE UTENSIL RODS

• Slide the lower duct cover up and above the

stop screw.

• Drive the stop screw in close to the frame.

• Slide the lower duct cover down against the top

of the hood. The duct cover should be seated into

the pocket on top of the hood.

• Install the side utensil rods with screws as shown.

20

La page est en cours de chargement...

Monogram ZV855SPSS Guide d'installation

Ce manuel convient également à

Monogram ZV855SPSS Guide d'installation

dans d''autres langues

Documents connexes

Autres documents