Superior Fireplaces DRL3500 Mode d'emploi

Marque: Superior Fireplaces

Modèle: DRL3500

Catégorie: Cheminées

Taper: Mode d'emploi

Ce manuel convient également à

DRL2000

- Do not store or use gasoline or other ﬂammable

vapors and liquids in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a neigh-

bor’s phone. Follow the gas supplier’s instruc-

tions.

• If you cannot reach your gas supplier, call the

ﬁre department.

- Installation and service must be performed by

a qualiﬁed installer, service agency or the gas

supplier.

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could

result in serious injury, death, or property damage.

AVERTISSEMENT:

RISQUED’INDENDIE OU D’EXPLOSION

Le non-respect Des avertissements de sécurité

pourrait d’entraîner des blessures graves, la mort

ou des dommages matériels.

- Ne pas entreposer ni utilizer d’essence ni d’autres

vapeurs ou liquides inﬂammables dans le voisinage

de cet appareil ou de tout autre appareil.

- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

• Ne pas tenter d’allumer d’appareil.

• Ne touchez à aucan interrupteur. Ne pas vous servir

des téléphones se trouvant dans le bâtiment où

vous trouvez.

• Sortez immédiatement de bâtiment.

• Appelez immédiatement votre fournisseur de

gaz depuis un voisin. Suivez les instructions du

fournisseur.

• Si vous ne pouvez rejoindre le fournisseur de gaz,

appelez le service des incindies.

- L’installation et l’entretien doivent être assurés par

un installateur ou un service d’entretien qualiﬁé

ou par le fournisseur de gaz.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future

reference.

Installateur : Laissez cette notice avec l’appareil.

Consommateur : Conservez cette notice pour

consultation ultérieure.

This appliance may be installed in an aftermarket permanently located, manufactured home (USA only)

or mobile home, where not prohibited by local codes. This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certiﬁed kit

is used.

Cet appareil peut installé dans une maison préfabriquée (mobile) déjà installée à demeure, si les réglements

locaux le permettent. Ce appareil doit être utilisé uniquement avec le type de gaz indiqué sure la plaque

signalétique. Cet appareil ne peut être converti à d’autres gaz, sauf si une trousse de conversion est utilsée.

Installation and Operation Instructions

Models

Report No. F19-008

Ce manuel est disponible en francais, simplement

en faire la demande. Numéro de la pièce 900994-02

P/N 900994-00 REV. F 06/2020

DRL2000 & DRL3500 Series Direct-Vent Gas Fireplaces

P900994-00

DRL2035TEN

DRL2045TEN

DRL2055TEN

DRL3535TEN

DRL3545TEN

DRL3555TEN

General Information

900994-00F, 06/2020

Innovative Hearth Products

DRL2000 & DRL3500 Series Direct-Vent Gas Fireplaces

DANGER

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

A barrier designed to reduce the risk of burns from the hot viewing glass is pro-

vided with this appliance and must be installed for the protection of children and

other at-risk individuals.

DANGER

VITRE CHAUDE

RISQUE DE BRÛLURES.

NE TOUCHEZ PAS UNE VITRE

NON REFROIDIE.

NE LAISSEZ JAMAIS UN ENFANT

DE TOUCHER LA VITRE.

L’écran pare-étincelles fourni avec ce foyer réduit le risque de brûlure en cas de

contact accidentel avec la vitre chaude et doit être installé pour la protection Des

enfants et Des personnes à risques.

Vea el volante adjunto para la representación de color adecuado

See attached color ﬂyer for proper color representation

Voir ci-joint tract pour une bonne représentation de la couleur

SAFETY AND YOUR FIREPLACE

PELIGRO

EL VIDRIO CALIENTE

CAUSARÁ QUEMADURAS.

USTED NUNCA DEBE

TOCAR EL VIDRIO CALIENTE.

LOS NIÑOS NUNCA DEBE

TOCAR EL VIDRIO.

Se provee con este aparato una barrera de proteccion (malla), diseñada para reducir

el riesgo de quemaduras por contacto accidental con el vidrio caliente que debe estar

instalada para proteccion de infantes y otros individuos en riesgo.

General Information

900994-00F, 06/2020

Innovative Hearth Products

DRL2000 & DRL3500 Series Direct-Vent Gas Fireplaces

 Aﬁn d’éviter les brûlures

graves ou les blessures,

ne pas retirer l’écran de

protection de la foyer qui

empêche tout contact

direct avec la vitre.

 Suivez les instructions de sécurité

ci-dessous et veillez à ce que tous

les membres de votre famille soient

conscients du danger de brûlure

encouru :

• Les surfaces de votre foyer deviennent

EXTRÊMEMENT CHAUDES !

• La vitre située à l'avant du foyer atteint

des températures EXTRÊMEMENT

ÉLEVÉES et peut causer de graves

blessures en cas de contact.

• Tenez les enfants à l'écart du foyer

lorsqu'il fonctionne. Surveillez

attentivement les enfants dans les

pièces où un foyer est utilisé aﬁn

d'éviter qu'ils ne soient en contact avec

la vitre.

• Tenez tous les vêtements, les meubles,

l'essence et tout autre liquide

inﬂammable à l'écart du foyer.

• Même après fermeture du gaz, les

surfaces du foyer restent extrêmement

chaudes.

 Veillez à coller les Étiquettes de mise

en garde relatives à la sécurité

d'utilisation à l'endroit où vous

utilisez le foyer, pour rappeler à tous

les utilisateurs les dangers liés aux

températures élevées

(Page 49)



Lisez L’information de sûreté

importante (Page 5)

Para evitar quemaduras y lesiones

graves, no quite el protector de malla

o guardia de seguridad que evita el

contacto directo con el vidrio.

 Siga las instrucciones de seguridad

a continuación y asegúrese de que

todos en su hogar sepan acerca de este

peligro de quemadura:

• ¡Las superﬁcies de la chimenea

estarán EXTREMADAMANTE

CALIENTES!!

• El vidrio delante de la

chimenea alcanza temperaturas

EXTREMADAMENTE ALTAS y puede

causar quemaduras graves si se toca.

• Mantenga a los niños alejados de

la chimenea en funcionamiento.

Supervise en forma cercana a los niños

en cualquier cuarto donde haya una

chimenea funcionando para impedir el

contacto con el vidrio.

• Mantenga la ropa, mobiliario, gasolina

y otros líquidos inﬂamables alejados

de la chimenea.

• Aún después de haber apagado el

gas, las superﬁcies de la chimenea

permanecen extremadamente

calientes.

 Asegúrese de colocar las Etiquetas de

advertencia de seguridad de operación

en el lugar donde enciende la chimenea,

para que todos recuerden los peligros

asociados con las altas temperaturas

(Página 49)



Lea Información importante de

seguridad (Página 5).

Seguridad y su

chimenea

La sécurité et

votre foyer

[FRENCH][ENGLISH]

[SPANISH]

Safety and Your

Fireplace

 To prevent severe burns

and injuries, do Not

remove the barrier on the

appliance which prevents

direct contact with the

glass.

 Follow the safety instructions below

and be sure everyone in your household

understands this burn hazard:

• The surfaces on your ﬁreplace get

EXTREMELY HOT!

• The glass on the front of the

ﬁreplace reaches EXTREMELY HIGH

temperatures and can cause severe

burns if touched.

• Keep children away from an operating

ﬁreplace. Closely supervise children

in any room where a ﬁreplace is

operating to prevent contact with glass.

• Keep clothing, furniture, gasoline, and

other ﬂammable liquids away from the

ﬁreplace.

• Even after the gas is turned off,

ﬁreplace surfaces remain extremely

hot.

 Be sure to attach the enclosed Safety-

in-Operation Warnings where you

turn on your ﬁreplace, to help remind

everyone of the dangers associated with

high temperatures

(Page 49)

 Read Important Safety Information

(Page 5)

All parts of your

IHP ﬁreplace get

EXTREMELY HOT!

Toutes les parties de votre

foyer IHP deviennent

EXTRÊMEMENT CHAUDES !

¡Todas las partes de la

chimenea IHP se ponen

MUY CALIENTES!

General Information

900994-00F, 06/2020

Innovative Hearth Products

DRL2000 & DRL3500 Series Direct-Vent Gas Fireplaces

THANK YOU FOR YOUR PURCHASE. WE APPRECIATE YOUR BUSINESS!

Please carefully read and follow all instructions in this manual. Pay special attention to all warnings and safety information. Following these

safety, care, and operation instructions will help ensure many years of dependable and enjoyable service from your ﬁreplace.

Please read and understand these instructions before installing, operating, or servicing this product.

We recommend that our

gas hearth products be

installed and serviced by

professionals who are

certied in the U.S. by the

National Fireplace Institute®

(NFI) as NFI Gas Specialists.

General Information

Safety and Your Fireplace...................................................................2

Important Safety Information ............................................................5

Fireplace Installation, Operation, and Maintenance Notices ............... 6

Packaging List ...................................................................................8

Introduction ....................................................................................... 8

Gas Pressure .....................................................................................9

Requirements for the Commonwealth of Massachusetts ................11

Cold Climate Insulation ....................................................................11

Manufactured Home Requirements .................................................12

Location ...........................................................................................12

Vent Termination Clearances ...........................................................13

Minimum Clearances to Combustibles ............................................15

Wall Finishes / Surrounds / Mantels ................................................16

Installation Preparation ....................................................................17

Installation

Installation Sequence ......................................................................17

Construct the Fireplace Framing ......................................................17

Prepare the Fireplace Top Spacers ...................................................19

Route the Gas Supply Line to the Fireplace .....................................19

Installing Header Shield Compass DLX Models ............................... 20

Rough in the Electrical Supply, if Needed ........................................21

Place the Fireplace in the Framing and Secure ................................21

Vent System Preparation

Select a Horizontal or Vertical Vent System ..................................... 21

Install the Vent Restrictor (if necessary) ..........................................21

Connecting the Vent Pipe.................................................................23

Install the Vent System .................................................................... 26

Complete the Field Wiring ................................................................39

Connect the Gas Line .......................................................................42

Verify Proper Fireplace Operation ....................................................43

Initializing The Remote Control System ........................................... 44

Install the Porcelain Liner Panels .....................................................45

Install the Glass Media ....................................................................45

Install Interior Options ..................................................................... 45

Install the Glass Door ......................................................................45

Adjust the Air Shutter to Ensure Proper Flame Appearance ............. 45

Install the Hood ...............................................................................47

Re-Installation of the Barrier ............................................................47

Blower Installation / Replacement ...................................................47

Re-installation of required screen barrier assembly ........................48

Install the Finishing Materials ..........................................................48

Attach the Safety-in-Operation Warnings.........................................48

Installation Accessories ................................................................... 50

Conversion Kits ...............................................................................52

Operation

Operation ......................................................................................... 53

Burn-in Period .................................................................................55

Accessing control compartment ...................................................... 55

Maintenance ....................................................................................60

Maintenance Schedule .....................................................................62

Accessory Components ...................................................................63

Lighting Instructions .......................................................................65

Troubleshooting ...............................................................................69

Replacement Parts ..........................................................................70

Warranty .......................................................................................... 75

DRL2035, DRL3535, DRL3545 & DRL3555 DRL2045 & DRL2055

General Information

900994-00F, 06/2020

Innovative Hearth Products

DRL2000 & DRL3500 Series Direct-Vent Gas Fireplaces

Important Safety Informa-

tion

1. WARNING: Do not operate appliance

with the glass front removed, cracked

or broken.

2. Do not use this appliance if any part

has been under water. Immediately

call a qualiﬁed service technician to

inspect the appliance and to replace

any part of the control system and

any gas control which has been under

water.

3. Due to high temperatures, the appli-

ance should be located out of trafﬁc

and away from furniture and draperies.

4. Children and adults should be alerted

to the hazards of high surface tem-

perature and should stay away to avoid

burns or clothing ignition.

5. Clothing or other ﬂammable material

should not be placed on or near the

appliance.

6. Young children should be carefully

supervised when they are in the same

room as the appliance. Toddlers,

young children, and others may be sus-

ceptible to accidental contact burns.

A physical barrier is recommended

if there are at-risk individuals in the

house. To restrict access to a ﬁreplace

or stove, install an adjustable safety

gate to keep toddlers, young children,

and other at-risk individuals out of the

room and away from hot surfaces.

7. Any safety screen, guard or barrier

removed for servicing an appliance

must be replaced prior to operating

the appliance.

8. Installation and repair should be done

by a qualiﬁed service person. The ap-

pliance should be inspected before use

and at least annually by a professional

service person. More frequent clean-

ing may be required due to excessive

lint from carpeting, bedding material,

et cetera. It is imperative that control

compartments, burners, and circulat-

ing air passageways of the appliance

be kept clean. See maintenance in-

structions on Page 60.

L’information de sûreté

importante

1. AVERTISSEMENT. Ne pas utiliser l’appareil

si le panneau frontal en verre n’est pas en

place, est craqué ou brisé.

2. Ne pas se servir de cet appareil s’il a été

plongé dans l’eau, même partiellement.

Faire inspecter l'appareil par un technicien

qualiﬁé et remplacer toute partie du systéme

de contrôle et toute commande qui ont été

plongées dans l'eau.

3. En raison des températures élevées,

l’appareil devrait être installé dans un en

droit où il y a peu de circulation et loin du

mobilier et des tentures.

4. Les enfants et les adultes devraient être

informés des dangers que posent les tem

pératures de surface élevées et se tenir à

distance aﬁn d’éviter des brûlures ou que

leurs vêtements ne s’enﬂamment.

5. On ne devrait pas placer de vêtements

ni d’autres matières inflammables sur

l’appareil ni à proximité.

6. Les jeunes enfants devraient être surveillés

étroitement lorsqu’ils se trouvent dans la

même pièce que l’appareil. Les tout petits,

les jeunes enfants ou les adultes peuvent

subir des brûlures s’ils viennent en contact

avec la surface chaude. Il est recommandé

d’installer une barrière physique si des

personnes à risques habitent la maison.

Pour empêcher l’accès à un foyer ou à un

poêle, installez une barrière de sécurité ;

cette mesure empêchera les tout petits, les

jeunes enfants et toute autre personne à ris

que d’avoir accès à la pièce et aux surfaces

chaudes.

7. Tout écran ou protecteur retiré pour per

mettre l’entretien de l’appareil doit être

remis en place avant de mettre l’appareil

en marche.

8. L’installation et la réparation devrait être

conﬁées à un technicien qualiﬁé. L’appareil

devrait faire l’objet d’une inspection par un

technicien professionnel avant d’être utilisé

et au moins une fois l’an par la suite. Des

nettoyages plus fréquents peuvent être

nécessaires si les tapis, la literie, et cetera

produisent une quantité importante de pous

sière. Il est essentiel que les compartiments

abritant les commandes, les brûleurs et les

conduits de circulation d’air de l’appareil

soient tenus propres. Voyez les instructions

d’entretien à la Page 60.

Información importante de

seguridad

1. ADVERTENCIA: No opere el artefacto con el

frente de vidrio quitado, agrietado o roto.

2. No use este artefacto si alguna de sus partes

ha estado bajo agua. Llame de inmediato

a un técnico de servicio caliﬁcado para

que inspeccione el artefacto y reemplace

cualquier parte del sistema de control y

cualquier control de gas que haya estado

bajo agua.

3. Debido a las altas temperaturas, el artefacto

debe situarse fuera de las áreas de tráﬁco y

lejos del mobiliario y cortinas.

4. Se debe alertar a los niños y adultos sobre

los peligros de las altas temperaturas en la

superﬁcie y que se mantengan alejados para

evitar quemaduras o ignición de la ropa.

5. No debe colocarse ropa u otros materiales

inﬂamables sobre y cerca del artefacto.

6. Se debe supervisar de cerca a los niños

cuando estén en el mismo cuarto que el

artefacto. Los niños pequeños, los jóvenes

y otras personas pueden ser susceptibles

a quemaduras por contacto accidental. Se

recomienda instalar una barrera física si hay

personas en riesgo en la casa. Para restringir

el acceso a una chimenea o estufa, instale

una puerta de seguridad ajustable para

mantener a los niños pequeños, jóvenes y

otras personas en riesgo fuera del cuarto y

lejos de las superﬁcies calientes.

7. Cualquier malla o resguardo de seguridad

quitado para dar servicio a un artefacto, debe

reinstalarse antes de operar el artefacto.

8. Una persona de servicio competente debe

realizar la instalación y reparación. Una

persona de servicio profesional debe

inspeccionar el artefacto antes de usar al

menos una vez por año. Se puede requerir

limpieza más frecuente debido a la pelusa

excesiva del alfombrado, del material de

cobijas, etc. Es imprescindible mantener

limpios los compartimientos de control, los

quemadores y los pasajes de circulación del

aire del artefacto. Ver las instrucciones de

mantenimiento en la página 60.

IMPORTANT SAFETY INFORMATION

[English]

[French]

[Spanish]

General Information

900994-00F, 06/2020

Innovative Hearth Products

DRL2000 & DRL3500 Series Direct-Vent Gas Fireplaces

APPLIANCE INSTALLATION, SERVICE, AND MAINTENANCE NOTICES

WARNING

Improper installation, adjustment, alteration, service or maintenance can cause injury or

property damage. Refer to this manual. For assistance or additional information consult a

qualiﬁed installer, service agency or the gas supplier.

AVERTISSEMENT

Une installation, un réglage,une modiﬁcation, une réparation ou un entretien mal effectué

peut causer des dommages matériels ou des blessures. Voir la notice de l’utilisateur qui

accompagne l’appareil. Pour de l’aide ou des renseignements supplémentaires, consultez

un installateur, un technicien agréé ou le fournisseur de gaz.

Only trim kit(s) supplied by the manufacturer shall be used in the installation of this ﬁreplace.

Seules des portes certiﬁées pour cet appareil doivent être utilisées.

These appliances must not be connected to a chimney or ﬂue serving a separate solid fuel

burning appliance.

Any change to this appliance and/or its operating controls is dangerous. Improper installation

or use of this appliance can cause serious injury or death from ﬁre, burns, explosion or

carbon monoxide poisoning.

CARBON MONOXIDE POISONING: Early signs of carbon monoxide poisoning are similar to

the ﬂu with headaches, dizziness and/or nausea. If you have these signs, obtain fresh air

immediately. Turn off the gas supply to the appliance and have it serviced by a qualiﬁed

professional, as it may not be operating correctly. Some people are more affected by carbon

monoxide than others, including pregnant women, people with heart or lung disease or

anemia, those under the inﬂuence of alcohol, and those at high altitudes.

Turn off gas and electrical power to the appliance and allow it to cool before cleaning or

servicing the appliance.

If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier

for this appliance.

Si l’écran est endommagé, il doit être remplacé par celui fournit par le fabricant de cet

appareil.

For use with barrier(s) Part No(s). F4248 (35” Models), F4249 (45” Models) and F4250 (55”

models). Follow installation instructions.

Reinstall any barrier removed before operating the appliance. The barrier is designed to

reduce the risk of burns from hot glass. Do not operate the appliance without the barrier

installed.

General Information

900994-00F, 06/2020

Innovative Hearth Products

DRL2000 & DRL3500 Series Direct-Vent Gas Fireplaces

APPLIANCE OPERATION NOTICES

WARRANTY INFORMATION

IMPORTANT SAFETY AND WARNING INFORMATION

CAUTION

Hot while in operation. Do not touch. Severe Burns may result. Keep children, clothing

furniture, gasoline and other liquids having ﬂammable vapors away.

ATTENTION

L’appareil est chaud lorsqu’il fonctionne. Ne pas toucher l’appareil. Risque de brûlures

graves. Surveiller les enfants. Garder les vêtements, les meubles, l’essence ou autres

liquides produisant des vapeur inﬂammables loin de l’appareil.

These ﬁreplaces are vented gas appliances. Do not burn wood or other material in these

appliances.

These appliances are designed to operate on natural gas or propane gas only. The use of

other fuels or combinations of fuels will degrade the performance of this system and may be

dangerous.

Provide adequate clearances around air openings and adequate accessibility clearance for

service and proper operation. Never obstruct the front openings of the appliance.

These appliances are designed as supplemental heaters. Therefore, it is advisable to have an

alternate primary heat source when installed in a dwelling.

Your gas appliance is covered by a limited 20-year warranty. You will ﬁnd a copy of the

warranty accompanying this manual. Please read the warranty to be familiar with its

coverage.

Retain this manual. File it with your other documents for future reference.

Failure to comply with the installation and operating instructions provided will result in an

improperly installed and operating appliance, voiding its warranty.

Do not attempt to alter or modify the construction of the appliance or its components. Any

modiﬁcation or alteration may void the warranty, certiﬁcation, and listings of this unit.

WARNING

This product can expose you to chemicals including Carbon Black, which is known to the

State of California to cause cancer, and Carbon Monoxide, which is known to the State of

California to cause birth defects or other reproductive harm. For more information go to

www.P65Warnings.ca.gov

General Information

900994-00F, 06/2020

Innovative Hearth Products

DRL2000 & DRL3500 Series Direct-Vent Gas Fireplaces

INSTALLATION

PACKAGING

All DRL2000 series models include

The assembled vented gas ﬁreplace heater is packaged with:

• Literature Kit (bag in bottom compartment containing Installation and Operation Instructions (this manual), Hot Glass Safety

Flyer, and Safety-In-Operation Warning Labels)

• 15 feet of two conductor wire

• 2.75” Non-combustible Board, 2 Side Brackets and 1 Center Bracket

•

35” & 45” models = 5 Lbs of Black Glass Media. (35” models use 3.5 lbs only) 55” models use = 7.5 lbs of Black

Glass Media

• 2 U-Shaped Vent Restrictors (seen on page 22)

• 1 Minimal Vent Run Bafﬂe (seen on page 22)

All DRL3500 series models include

The assembled vented gas ﬁreplace heater is packaged with:

• Literature Kit (bag in bottom compartment containing Installation and Operation Instructions (this manual), Hot Glass Safety

Flyer, and Safety-In-Operation Warning Labels)

• Elbow Heat Shield

• Header heat shield

• 4.75” non-combustible board 2 side brackets and 1 center bracket

•

35” & 45” models = 5 Lbs of Platinum Glass Media. (35” models use 3.5 lbs only) 55” models use 7.5 lbs of

Platinum Glass Media.

• Remote Control

• 1 Wall Heatshield (3500 series models only - bend wall Heatshield as shown in Figure 24A, Page 32)

• 2 U-Shaped Vent Restrictors (seen on page 22)

• 1 Minimal Vent Run Bafﬂe (seen on page 22)

INTRODUCTION

These vented gas ﬁreplace heaters are sealed combustion, air-circulating gas ﬁreplaces designed for residential and commercial

applications.

Electronic ﬁreplaces are designed with an electronic intermittent pilot ignition system. External electrical power is required to

operate these units. In the event of a power outage, four (4) AA batteries (in battery holder) provide backup power for ﬁreplace

operation (excluding the blower).

NOTE: Installation and repair should be done by a qualiﬁed service person. The ﬁreplace should be inspected before use and at

least annually by a professional service person. More frequent cleaning may be required due to excessive lint from carpeting,

bedding material, etcetera. It is imperative that control compartment, burners and circulating air passageways of the ﬁreplace be

kept clean.

Remarqué : L’installation et la réparation devrait être conﬁées à un technicien qualiﬁé. L’appareil devrait faire l’objet d’une

inspection par un technicien professionnel avant d’être utilisé et au moins une fois l’an par la suite. Des nettoyages plus

fréquents peuvent être nécessaires si les tapis, la literie, et cetera produisent une quantité importante de pous-sière. Il est

essentiel que les compartiments abritant les commandes, les brûleurs et les conduits de circulation d’air de l’appareil soient

tenus propres.

NOTE: Diagrams and illustrations are not necessarily shown to scale.

Approved Vent Components

These ﬁreplaces are designed, tested and listed for operation and installation with the following vent components only:

• Secure Vent

Direct-Vent System Components,

• Secure Flex

Flexible Vent Components, and

• Z-FLEX

Model GA Venting Systems listed to UL1777 and ULCS635 manufactured by Flexmaster Canada Limited.

Use only the correct size venting (4-1/2” inner and 7-1/2” outer).

These approved vent system components are labeled for identiﬁcation. DO NOT use any other manufacturer’s vent components

with these ﬁreplaces.

Codes and Standards

These ﬁreplaces comply with National Safety Standards and are tested and listed by PFS TECO (Report No. F19-008) to ANSI

Z21.88 (in Canada, CSA-2.33), and CAN/CGA-2.17-M91 in both USA and Canada, as vented gas ﬁreplace heaters.

These ﬁreplaces are listed for installation in bedrooms and manufactured homes.

The installation must conform to local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA

54—latest edition (In Canada, the current CAN/CGA-B149.1 installation code).

The ﬁreplace, when installed, must be electrically grounded and wired in accordance with local codes or, in the absence of local

codes, with the National Electrical Code, ANSI/NFPA 70—latest edition, or the Canadian Electrical Code, CSA C22.1—latest edition.

General Information

900994-00F, 06/2020

Innovative Hearth Products

DRL2000 & DRL3500 Series Direct-Vent Gas Fireplaces

BTU Input

Gas Pressure

Table 3 - Inlet Line Gas Pressures

Fuel Minimum Maximum

Natural Gas 5” WC / (1.25 kPa) 10.5” WC / (2.61 kPa)

Propane/LP 11.0” WC / (2.74 kPa) 13.0” WC / (3.23 kPa)

Table 4 - Manifold Outlet Gas Supply Pressure

Fuel Pressure

Natural Gas 3.5” WC / (0.87 kPa)

Propane/LP 10.0” WC / (2.49 kPa)

Test gauge connections are provided on the front of the millivolt gas control valve (identiﬁed IN for the inlet and OUT for

the manifold side). The control valves have a 3/8” (10 mm) NPT thread inlet and outlet side of the valve (Figures 1 & 1A).

Based on CSA P. 4.1-2015

* AFUE is a measurement of the US Department of

Energy,

** Complies with CSA P.4.1-2015 “Testing Method

for Measuring Annual Fireplace Efﬁciency. P4

(EnerGuide) is a measurement of the Canadian Ofﬁce

of Energy Efﬁciency. Efﬁciencies are based on Normal

input operation.

Note: **CPI disabled per addendum instructions

900949-00 (provided with this appliance).

Table 1 - Input Rate (BTU/HR), Gas Valves

Burner Model

Natural Gas

Propane/LP Gas

(Field Converted)

High Rate Low Rate High Rate Low Rate

DRL2035 15,000 13,000 14,000 12,000

DRL2045 18,000 14,000 16,000 13,000

DRL3535 18,000 12,000 16,000 13,000

DRL3545 23,000 16,000 21,000 17,000

DRL2055 23,000 19,000 21,000 17,000

DRL3555 28,000 19,000 27,000 21,000

Table 2 - Thermal Efﬁciency (%)

Figure 1 - Electronic Gas Valve PF2 Figure 1A - Electronic Gas Valve PF1

Inlet 3/8” NPT

Outlet 3/8”

NPT

Outlet

Pressure

Tap

Pilot Outlet

7/16” UNS

Inlet

Pressure

Tap

Orange Wire

(from DFC Wire

Harness)

Pressure

Regulator

Tower

Main Gas Inlet

3/8" NPT

Green Wire

(from DFC Wire Harness)

Inlet (IN) Test Port

Manifold (OUT)

Test Port

Connect GTMS

wire harness

Yellow Ground Wire

(from DFC Wire

Harness)

Side View

Burner Model

Electronic Electronic

AFUE * P4 AFUE * P4

Natural Natural Propane/LP Propane/LP

DRL2035 68.9 63.64 53.7 62.8**

DRL2045 70.7 67.11 56.6 64.5

DRL3535 69.2 65.11 55.3 63.1**

DRL3545 66.9 62.4 61.9 65

DRL2055 69.4 62.7 64.8 64.4

DRL3555 67.7 62.4 61 63.4

Note: *Propane/ LP models are available through

Field conversion only

Installation

900994-00F, 06/2020

Innovative Hearth Products

DRL2000 & DRL3500 Series Direct-Vent Gas Fireplaces

The appliance and its appliance main gas valve must be disconnected from the gas supply piping system during

any pressure testing of that system at test pressures in excess of 1/2 psi (3.5 kPa).

The appliance must be isolated from the gas supply piping system by closing its equipment shutoff valve during

any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psi (3.5 kPa).

Oriﬁce Sizes—Sea Level to High Altitude

These ﬁreplaces are tested and approved for installation at elevations of 0 - 4500 ft (0 - 1372 m) above sea level

using the standard burner oriﬁce sizes (Table 5). For elevations above 4500 ft, contact your gas supplier or qualiﬁed

service technician.

Deration

At elevations above 4500 ft, the amount of BTU fuel value delivered must be reduced by either:

• Using gas that has been derated by the gas company.

• Changing the burner oriﬁce to a smaller size as regulated by the local authorities having jurisdiction and by the

(USA) National Fuel Gas Code NFPA 54/ANSI Z223.1—latest edition or, in Canada, the CAN/CGA-B149.1 codes—

latest edition.

NOTE: Flame breadth, height and width will diminish 4% for every 1,000 ft of altitude.

IN CANADA—CAN/CGA-2.17-M91 (HIGH ALTITUDE):

THE CONVERSION SHALL BE CARRIED OUT BY A MANUFACTURER’S AUTHORIZED REPRESENTATIVE,

IN ACCORDANCE WITH THE REQUIREMENTS OF THE MANUFACTURER, PROVINCIAL OR TERRITORIAL

AUTHORITIES HAVING JURISDICTION AND IN ACCORDANCE WITH THE REQUIREMENTS OF THE CAN/

CGA-B149.1 OR CAN/CGA-B149.2 INSTALLATION CODES.

Burner Model Natural Gas - drill size * Propane/LP Gas - drill size

DRL2035 #49 (0.073”), Cat. No. 21L82 CAT: J7385 #57 (.043”)

DRL2045 #47 (0.0785”), Cat. No. 99K74 CAT: 62L37 #56 (.046”)

DRL2055 #47 (0.0785”), Cat. No. 99K74 CAT: 19L52 #55 (.052”)

DRL3535 #43 (0.089”), Cat. No. 99K75 CAT: 62L37 #56 (.046”)

DRL3545 #43 (.089”) Cat No. 99K75 CAT: 19L52 #55 (.052”)

DRL3555 #40 (.098”) Cat No. 69L96 CAT: 39L10M #53 (.0595”)

* Standard size installed at factory

Table 5 - Burner Oriﬁce Sizes, Elevation 0 - 4500 ft ( 0 - 1372 m)

NOTE: Before accessing the test ports, the ﬁreplace must be OFF and COLD. Turn OFF the main gas supply before

connecting to the pressure taps.

Propane tanks are at pressures that will cause damage to valve components. Verify that the tanks have step down regulators

to reduce the pressure to safe levels.

Using a propane tank smaller than 100 lbs may create pressure loss and insufﬁcient fuel delivery, which can cause sooting,

severe delayed ignition, or other malfunctions (see NPFA 58).

Any damage as a result of insufﬁcient tank size or other improper installation is NOT covered under the limited warranty.

Installation

900994-00F, 06/2020

Innovative Hearth Products

DRL2000 & DRL3500 Series Direct-Vent Gas Fireplaces

COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS

These appliances are approved for installation in the US state of Massachusetts if the following additional

requirements are met:

• Install this appliance in accordance with Massachusetts Rules and Regulations 248 C.M.R. Sections 4.00

through 8.00.

• Installation and repair must be done by a plumber or gas ﬁtter licensed in the Commonwealth of Massachusetts.

• The ﬂexible gas line connector used shall not exceed 36 inches (92 centimeters) in length.

• The individual manual shut-off must be a T-handle type valve.

Massachusetts Horizontal Vent Requirements

In the Commonwealth of Massachusetts, horizontal terminations installed less than seven (7) feet above the ﬁnished

grade must comply with the following additional requirements:

• A hard wired carbon monoxide detector with an alarm and battery back-up must be installed on the ﬂoor level

where the gas ﬁreplace is installed. The carbon monoxide detector must comply with NFPA 720, be ANSI/UL

2034 listed and be ISA certiﬁed.

• A metal or plastic identiﬁcation plate must be permanently mounted to the exterior of the building at a minimum

height of eight (8) feet above grade and be directly in line with the horizontal termination. The sign must

read, in print size no less than one-half (1/2) inch in size, GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL

OBSTRUCTIONS.

COLD CLIMATE INSULATION

For cold climate installations, seal all cracks around your ﬁreplace with noncombustible material and wherever cold

air could enter the room. It is especially important to insulate outside chase cavity between studs and under ﬂoor on

which ﬁreplace rests, if ﬂoor is above ground level. Gas line holes and other openings should be caulked or stuffed

with unfaced ﬁberglass insulation.

NOTE: Do not use loose, or blown-in insulation in the cavity surrounding the ﬁreplace.

If the ﬁreplace is being installed on a cement slab in cold climates, a sheet of plywood or other raised platform can

be placed underneath to prevent conduction of cold transferring to the ﬁreplace and into the room. It also helps to

seal inside surfaces and tape for maximum air tightness and caulk ﬁrestops.

Installation

900994-00F, 06/2020

Innovative Hearth Products

DRL2000 & DRL3500 Series Direct-Vent Gas Fireplaces

MANUFACTURED HOME REQUIREMENTS

This appliance may be installed in an aftermarket, permanently located, manufactured home (USA only) or mobile

home, where not prohibited by local codes.

Cet appareil peut être installé dans une maison préfabriquée (mobile) déjà installée à demeure si les règlements

locaux le permettent.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for

use with other gases.

Cet appareil doit être utilisé uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil ne

peut être converti à d’autres gaz.

CAUTION

Ensure that the cross members are not cut or weakened during installation. The structural

integrity of the manufactured home ﬂoor, wall, and ceiling / roof must be maintained.

CAUTION

This appliance must be grounded to the chassis of the manufactured home in accordance

with local codes or in the absence of local codes, with the National Electrical Code ANSI /

NFPA 70—latest edition or the Canadian Electrical Code CSA C22.1—latest edition.

LOCATION

In selecting the location, the aesthetic and functional use of the ﬁreplace are primary concerns. However, vent

system routing to the exterior and access to the fuel supply are also important.

Due to high temperatures, the ﬁreplace should be located out of trafﬁc and away from furniture and draperies.

En raison des températures élevées, l’appareil devrait être installé dans un endroit où il y a peu de

circulation et loin du mobilier et des tentures.

The location should also be free of electrical, plumbing or other heating/air conditioning ducting.

These direct-vent ﬁreplaces are uniquely suited for installations requiring a utility shelf positioned directly above the

ﬁreplace. Utility shelves like these are commonly used for locating television sets and decorative plants.

Be aware that this is a heat producing ﬁreplace. Objects placed above the unit are exposed to elevated temperatures.

Do not insulate the space between the ﬁreplace and the area above it.

The minimum height from the base of the ﬁreplace to the underside of combustible materials used to construct a

utility shelf in this fashion is shown in Table 9, page 15.

Figure 2 - Typical Locations and Venting

HORIZONTAL VENT

(Rear Vent Application with a chase)

HORIZONTAL VENT

(Top Vent Application)

VERTICAL VENT

(Top Vent Application)

(Rear Vent Application)

VERTICAL VENT

(Rear Vent Application without a chase)

HORIZONTAL VENT

Horizontal Vent

(Top Vent)

Vertical Vent

(Top Vent)

HORIZONTAL VENT

(Rear Vent Application with a chase)

HORIZONTAL VENT

(Top Vent Application)

VERTICAL VENT

(Top Vent Application)

(Rear Vent Application)

VERTICAL VENT

(Rear Vent Application without a chase)

HORIZONTAL VENT

Top Vent

Top Vent Top Vent

Top Vent

Recessed

Installation

NOTE: Installations against side walls must meet requirements

shown in Figure 6, Page 16.

NOTE: Unit is required to be a minimum

of 6” off ﬂoor to install optional facade.

Installation

900994-00F, 06/2020

Innovative Hearth Products

DRL2000 & DRL3500 Series Direct-Vent Gas Fireplaces

VENT TERMINATION CLEARANCES

These instructions should be used as a guideline and do not supersede local codes in any way. Install venting with the

most restrictive requirements as outlined in these instructions, local codes, these instructions, the current National Fuel

Gas Code (ANSI Z223.1/NFPA 54) in the USA or the current standards of CAN/CGA-B149.1 in Canada.

Vertical Vent Termination Clearances

Terminate multiple vent terminations according to the installation codes listed above and Figure 3.

Figure 3 - Multiple Terminations

6”

(153 mm)

12”

(305 mm)

minimum

Terminate single vent caps relative to building components according to Table 6.

Table 6 - Termination Heights for Vents above Flat or Sloped Roofs (NFPA 54 / ANSI Z223.1)—Gas Vent Rule

Roof Pitch Termination Height *

Flat to 6/12 1.0 ft (0.3 m)

6/12 to 7/12 1.25 ft (0.38 m)

7/12 to 8/12 1.5 ft (0.46 m)

8/12 to 9/12 2.0 ft (0.61 m)

9/12 to 10/12 2.5 ft (0.76 m)

10/12 to 11/12 3.25 ft (0.99 m)

11/12 to 12/12 4.0 ft (1.22 m)

12/12 to 14/12 5.0 ft (1.52 m)

14/12 to 16/12 6.0 ft (1.83 m)

16/12 to 18/12 7.0 ft (2.13 m)

18/12 to 20/12 7.5 ft (2.29 m)

20/12 to 21/12 8.0 ft (2.44 m)

Roof pitch is X/12

2 ft

minimum

2 ft minimum

Lowest

discharge

opening

*H = minimum height from roof to

lowest discharge opening of vent

Horizontal overhang

Vertical

wall

Vent

termination

Storm collar

Concentric

vent pipe

Flashing

1” (26mm) minimum

clearance to combustibles

TERMINATION HEIGHTS FOR VENTS ABOVE

FLAT OR SLOPED ROOFS

Horizontal Vent Termination Clearances

The horizontal vent termination must have a minimum of 6” (152 mm) clearance to any overhead combustible

projection of 2-1/2” (64 mm) or less (Figure 4). For projections exceeding 2-1/2” (64 mm) (Figure 4). For additional

vent location restrictions refer to Table 7, page 14.

All horizontal terminations may be located as close as 6” (152mm) to any (non-combustible and combustible) exterior

sidewall. This distance may be decreased to 2” (51mm) for noncombustible exterior sidewalls with all approved

terminations (Table 7, page 14).

Figure 4 - Horizontal Vent Termination Clearances

Combustible projection

2-1/2” or less in length

Combustible projection

greater than 2-1/2” in length

Ventilated

sofﬁt - 18”

(457 mm)

Unventilated

sofﬁt - 12”

(305 mm)

6” (152mm)

Termination kit

6”

Installation

900994-00F, 06/2020

Innovative Hearth Products

DRL2000 & DRL3500 Series Direct-Vent Gas Fireplaces

Table 7 - Horizontal vent termination clearances for buildings with combustible and noncombustible exteriors

U.S. Installation ** Canadian Installation *

A Clearance above grade, veranda, porch, desk, or balcony 12” (300 mm) ** 12” (300 mm) *

B Clearance to window or door that may be opened 6” (150 mm)

for ﬁreplaces < 10,000 Btu/h (3 kW),

9” (230 mm)

for ﬁreplaces > 10,000 Btu/h (3 kW), and < 50,000 Btu/h (15

kW),

12” (300 mm)

for ﬁreplaces > 50,000 Btu/h (15 kW) **

6” (150 mm)

for ﬁreplaces < 10,000 Btu/h (3 kW),

12” (300 mm)

for ﬁreplaces > 10,000 Btu/h (3 kW)

C Clearance to permanently closed window 9” (229 mm)

recommended to prevent window condensation

12” (305 mm)

recommended to prevent window

condensation

D Vertical clearance to ventilated sofﬁt located above the

termination within a horizontal distance of 18” (458 mm)

18” (458 mm) 18” (458 mm)

E Clearance to unventilated sofﬁt 12” (305 mm) 12” (305 mm)

F Clearance to outside corner 5” (127 mm)

minimum

5” (127 mm)

minimum

G Clearance to inside corner 6” (152 mm) minimum 6” (152 mm) minimum

H Clearance to each inside of center line extended above

meter / regulator assembly

36” (910 mm)

within a height of 15 ft above the meter / regulator assembly **

36” (910 mm)

within a height of 15 ft above the meter /

regulator assembly *

I Clearance to service regulator vent outlet 36” (910 mm)** 36” (910 mm)*

J Clearance to nonmechanical air supply inlet to building or

the combustion air inlet to any other ﬁreplace

6” (150 mm)

for ﬁreplaces < 10,000 Btu/h (3 kW),

9” (230 mm)

for ﬁreplaces > 10,000 Btu/h (3 kW) and < 50,000 Btu/h (15 kW),

12” (300 mm)

for ﬁreplaces > 50,000 Btu/h (15 kW)**

6” (150 mm)

for ﬁreplaces < 10,000 Btu/h (3 kW),

12” (300 mm)

for ﬁreplaces > 10,000 Btu/h (3 kW)

K Clearance to a mechanical air supply inlet 36” (910 mm) above if within 10 ft (3 m) horizontally ** 72” (1830 mm) *

L Clearance above paved sidewalk or paved driveway located

on public property

84” (2130 mm) ‡ 84” (2130 mm) ‡

M Clearance under veranda, porch, deck or balcony 12” (300 mm) *‡ 12” (300 mm) *‡

N Depth of alcove (maximum) 72” (1830 mm) ** 72” (1830 mm) *

O Clearance to termination (alcove) 6” (15.2 mm) ** 6” (15.2 mm)*

P Width of alcove (minimum) 36” (910 mm) ** 36” (910 mm) *

Q Clearance to combustible above (alcove) 18” (457 mm) ** 18” (457 mm) *

‡

*‡

In accordance with the current CAN/CGA-B149.1 National Gas And Propane Installation Code

In accordance with the current ANSI Z223.1/NFPA 54 National Fuel Gas Codes

A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings

Only permitted if veranda, porch, deck, or balcony is fully-open on a minimum two sides beneath the ﬂoor

Fixed

Closed

Openable

Fixed

Closed

TERMINATION CAP

AIR SUPPLY INLET

GAS METER RESTRICTED AREA

(TERMINATION PROHIBITED)

Openable

See Table 6

Inside Corner

Outside Corner Recessed Location

Balcony with No Side Wall

Balcony with Perpendicular Side Wall

Installation

900994-00F, 06/2020

Innovative Hearth Products

DRL2000 & DRL3500 Series Direct-Vent Gas Fireplaces

MINIMUM CLEARANCES TO COMBUSTIBLES

Fireplace And Vent Clearances

The ﬁreplace is approved with zero clearance to combustible materials

on all sides (Table 8), with the following exception: The unit may not be

recessed (allowance made for mantel legs / side trim in Figure 6, page

16). When the unit is installed with one side ﬂush with a wall, the wall

on the other side of the unit must not extend beyond the front edge of

the unit (Figure 6, page 16).

The ﬁreplace must be mounted on a fully supported base extending

the full width and depth of the unit. The ﬁreplace may be located on

or near conventional construction materials. However, if installed on

combustible materials, such as carpeting, vinyl tile or other combustible

material other than wood ﬂooring, the appliance shall be installed on a

metal or wood panel extending the full width and depth of the appliance.

Table 8 - Minimum Clearances *

Back ***

1/2” (13 mm) to wrapper

0” (0 mm) to Spacers

Sides

1/2” (13 mm) to wrapper

0” (0 mm) to Spacers **

Top Standoffs 0” (0 mm) to top standoffs

Floor 0” (0 mm) ***

From Bottom of Unit to Ceiling 52” (1321 mm)

Vent

3” (77 mm)—Top *

1” (26 mm)—Sides and Bottom

Front Service Clearance—

clearance immediately in front of

viewing area(s)

36” (914 mm)

* 3” (77 mm) above any horizontal/inclined vent component.

** See Page 21 for clearance requirements to the nailing ﬂange

located at each side of the unit and any screw heads adjacent to it.

*** 6” (153 mm) if optional facade is used.

Hearth Extension

A hearth extension is not required with this ﬁreplace. Any hearth extension used is for appearance only and does not have to conform to

standard hearth extension installation requirements.

Shelf Height

To provide for the lowest possible shelf surface, the venting attached to the top vent should be routed in a way to minimize obstructions to

the space above the ﬁreplace. Do not insulate the space between the ﬁreplace and the area above it (Table 9). The minimum height from

the base of the ﬁreplace to the underside of combustible materials used to construct a utility shelf in this fashion is shown in Table 9.

Table 9- Combustible Shelf Height—Top Vent

Model

Top Vent with one 90° Elbow *

(55” models require 12” of vertical rise directly off unit)

Shelf Height

(see table)

The unit is

required to be a

minimum of 6”

off ﬂoor to install

optional facade.

Secure Vent

(using rigid elbow)

Secure Flex

(using ﬂex elbow)

35” Models 47” (1194 mm) 49” (1245 mm)

45” Models 52” (1321 mm) 54” (1372 mm)

55” Models 62” (1575 mm) 64” (1626 mm)

CLEARANCES TO COMBUSTIBLES MUST BE MAINTAINED:

No combustible materials or insulation is permitted in the shaded area

between the appliance and the shelf above it.

WARNING: CRITICAL INSTALLATION INFORMATION THAT IF NOT FOL-

LOWED CAN RESULT IN A SAFETY HAZARD!

Installation

900994-00F, 06/2020

Innovative Hearth Products

DRL2000 & DRL3500 Series Direct-Vent Gas Fireplaces

Wall Finishes / Surrounds / Mantels

NOTE: Combustible wall ﬁnish materials and/or surround materials must not be allowed to encroach the area

deﬁned by the ﬁreplace front face (black sheet metal). Non-combustible material up to 6 inches in depth, such as

surrounds may be positioned in front of or overlapping the ﬁreplace face.

Non-combustible materials, such as surrounds and other ﬁreplace trim, may be installed on the ﬁreplace face, but they

must not cover any portion of the removable glass panel or impede the removal or installation of screen barrier assembly.

Vertical installation clearances to combustible mantels vary according to the depth of the mantel (Figures 5 and

5A). Mantels constructed of non-combustible materials may be installed at any height above the ﬁreplace opening.

However, do not allow anything to hang below the ﬁreplace hood.

Minimum clearance requirements include any projections such as shelves, window sills, mantels, etc. above the

ﬁreplace.

NOTE: To avoid heat-related ﬁnish damage, we recommend the use of high temperature paint (rated 175° F or higher) on

the underside of the mantel.

Figure 6 - Combustible Side Clearances

3-1/2”

(89 mm)

6”

(152 mm)

Top View of

Fireplace

Combustible

mantel legs may

project beyond either side

of the fireplace opening

as long as they are kept

within the shaded area

illustrated here.

Combustible Materials

Allowed In Shaded Area

“Safe Zone”

Combustible Walls

shown in dark gray

At 6” minimu

side wall clearance,

a combustible wall

can project to an

length

Figure 5A - Mantel height DRL3500 series models

(305)

(254)

(203)

(152)

(102)

(51)

in. (mm)

6 (153)

8 (203)

10 (254)

12 (305)

14 (356)

16 (407)

Hood

Fireplace

Mantel depth

Figure 5 - Mantel height DRL2000 series models

(305)

(254)

(203)

(152)

(102)

(51)

in. (mm)

4 (102)

6 (153)

8 (203)

10 (254)

12 (305)

14 (356)

Hood

Fireplace

Mantel depth

Installation

900994-00F, 06/2020

Innovative Hearth Products

DRL2000 & DRL3500 Series Direct-Vent Gas Fireplaces

INSTALLATION PREPARATION

The ﬁreplace is shipped with all gas controls and components installed and pre-wired. Before installing the ﬁreplace, follow

these steps:

1. Remove the shipping carton, and retain the front of the carton (used to protect the ﬁreplace during construction).

2. Remove the shipping pad, exposing the front glass door.

3. Remove the glass door (Page 59).

NOTE: Barrier must be removed to remove the door. Barrier must be protected from damage and construction dust and dirt.

NOTE: Place the glass door on the shipping carton to protect its surface.

INSTALLATION SEQUENCE

The typical sequence of installation is outlined below; however, each installation is unique and may result in variations to the

steps described.

See the pages referenced in the following steps for detailed instructions.

Check local codes for more restrictive installation. The more restrictive installation for clearances must be used.

Framing

1. Construct the Fireplace Framing (Page 17).

2. Prepare the Fireplace Top Spacers (Page 19).

3. Installing Non-Combustible Front Fireboard Standoff (Page 19).

4. Route the Gas Supply Line to the Fireplace (Page 19).

5. Installing Header Shield (Page 20).

6. Rough in the Electrical Supply, if Needed (Page 21).

7. Place the Fireplace in the Framing and Secure (Page 21).

Venting

8. Select a Horizontal or Vertical Vent System (Page 21).

9. Install the Vent Restrictor (if necessary) (Page 21).

10. Connecting the Vent Pipe (Page 23).

11. Install the Vent System (Page 26).

Electrical Connection

12. Complete the Field Wiring (Page 39).

Gas Connection

13. Connect the Gas Line (Page 42).

14. Verify Proper Fireplace Operation (Page 43).

Finishing

15. Initializing the Remote Control System (Page 44).

16. Install the Porcelain Liners (Page 45).

17. Install the Glass Media (Page 45).

18. Install Interior Options(Page 45)(see Accessory Components Page 62) - (follow instructions included with optional accessories)

19. Install the Glass Door (Page 45).

20. Adjust the Air Shutter to Ensure Proper Flame Appearance (Page 45).

21. Install the Hood (Page 47).

22. Re-installation of the barrier assembly (Page 47).

23. Installation / replacement of blower (Page 47).

24. Installation/Re-installation of the barrier assembly (Page 48).

25. Install the Finishing Materials (Page 48).

26. Attach the Safety-in-Operation Warning Labels (Page 48).

1. Construct the Fireplace Framing

1. Frame the ﬁreplace as illustrated in Table 10, page 18. For corner framing installations, use Table 11, page 18. All framing details must

allow for a minimum clearance to combustible framing members as shown in Table 8, page 15.

2. If the ﬁreplace is to be elevated above ﬂoor level, a solid continuous platform must be constructed below the ﬁreplace.

NOTE: Headers may be in direct contact with the ﬁreplace top standoff spacers when they are bent up vertically, maintaining the 4”

clearance to the ﬁreplace top, but must not be supported by them or notched to ﬁt around them. All construction above the ﬁreplace

must be self-supporting. DO NOT use the ﬁreplace for structural support.

Installation

900994-00F, 06/2020

Innovative Hearth Products

DRL2000 & DRL3500 Series Direct-Vent Gas Fireplaces

Top View Front View

Left Side View Right Side View

Blower

access

panel

Hood

Junction

box access

Gas line

access

* C and D are glass viewing area dimensions

Inches (millimeters)

Model A B C* D* E F G H I J K

35” Models 24-3/4 (629) 23-1/4 (591) 16-3/4 (426) 30 (762) 35-1/2 (902) 24-3/4 (629) 12-3/8 (315) 32-7/8 (835) 6-1/2 (166) 17 (432) 10-5/8 (270)

45” Models 24-3/4 (629) 23-1/4 (591) 16-3/4 (426) 40 (1016) 45-1/2 (1156) 34-3/4 (883) 17-3/8 (442) 42-7/8 (1089) 6-1/2 (166) 17 (432) 10-5/8 (270)

55” Models 24-3/4 (629) 23-1/4 (591) 16-3/4 (426) 50 (1270) 55-1/2 (1410) 44-3/4 (1137) 22-3/8 (569) 52-7/8 (1344) 6-1/2 (166) 17 (432) 10-5/8 (270)

Table 12 - Fireplace Speciﬁcations

Model A * B C D E

35” Models

35-7/8

(911)

(737)

(1067)

(458)

31-1/2

(547)

45” Models

45-7/8

(1165)

(737)

(1067)

(458)

31-1/2

(547)

55”

55-7/8

(1420)

(737)

(1067)

(458)

N/A

C = Height for installations with 12” section directly off unit then elbow

E = Height for installations with elbow directly off unit (see note below)

* Minimum opening size; additional 1/8” per side is recommended.

NOTE: Framing speciﬁcations do NOT apply for ﬂexible venting.

When using ﬂexible venting, refer to the kit requirements for framing

speciﬁcations.

NOTE: 35” & 45” model = Strongly recommend at least 1 ft of

vertical rise directly off top of unit. 55” = 1 ft of vertical rise is

required directly off unit.

1/2 A

NOTE: Dimension “D” is for

ﬂush framing.

Inches (millimeters)

Framing construction to be

2 x 4, or larger.

7 (178)

12-1/8

(308)

10-1/2

(267)

5-1/8(130)

Table 10 - Fireplace Framing Speciﬁcations

Table 11 - Fireplace Framing Speciﬁcations - Corner Installation with Horizontal Termination

0” (0)

6” (308) Min. if Optional

Facade is Used

Model A B C D E

35”

35-7/8

(911)

59-1/2

(1511)

42-1/8

(1070)

30-1/4

(768)

14-1/4

(362)

45”

45-7/8

(1165)

70-3/8

(1788)

49-3/4

(1264)

35-1/4

(895)

17-1/2

(445)

55”

55-7/8

(1420)

82-3/4

(2102)

58-1/2

(1486)

41-3/8

(1051)

21-1/2

(547)

Back wall of chase/enclosure (including ﬁnishing materials)

7 (178)

Front to rear with 1” distance to wall

Inches

(millimeters)

Installation

900994-00F, 06/2020

Innovative Hearth Products

DRL2000 & DRL3500 Series Direct-Vent Gas Fireplaces

Prepare the Fireplace Top Spacers

1. The two (2) 4” standoff spacers on top of the ﬁreplace cabinet are shipped ﬂat. Remove the screw adjacent to the

detached end (Figure 7).

2. Bend the standoffs as shown (Figure 7A):

3. Align the hole in the standoff with the hole in the ﬁreplace top, and secure with the screw that was removed in

Step 1 (Figure 7A).

Figure 7 - Unassembled standoff

Figure 8 - Non-Combustible Front Fireboard Standoff

Figure 7A - Assembled standoffs

Positioned ﬂat as shipped from the factory

Fireplace Front

Top Standoff

Screw

Fireplace

Front

Top Standoff

4. Route the Gas Supply Line to the Fireplace

1. Route a 1/2” (13 mm) gas line to the left side of the ﬁreplace (Figure 9).

NOTE: Gas lines must be routed, assembled, and made of materials that are in strict accordance with local codes and

regulations. All ﬁreplaces are factory-equipped with a ﬂexible gas line connector and a 1/2” shutoff valve (Page 42).

Figure 9 - Routing the gas line - all models

Left side front corner of

ﬁreplace framing

Pipe coupling

(recommended)

7-5/8”

(195 mm)

3”

(77 mm)

Separate and note metal side (2)

and center (1) brackets.

Step 1: Remove two screws from the top and side of the unit. Bend the side bracket securing tab over the edge

of the unit and secure. Secure bracket to the top through the clearance screw hole.

3. Installing Non-Combustible Front Fireboard Standoff

A non-combustible standoff board is provided with the ﬁreplace to prevent overlap of drywall or other material of portions of the ﬁreplace that may

be prone to the buildup of heat. It is supported by a middle bracket and two side brackets.

Note: DRL3535TEN and DRL3545TEN models require a 4.75” non-combustible ﬁreboard (provided) while DRL2035TEN and DRL2045TEN models

require a 2.75” non-combustible board (provided).

Installation

900994-00F, 06/2020

Innovative Hearth Products

DRL2000 & DRL3500 Series Direct-Vent Gas Fireplaces

Proper Sizing of Gas Line

Properly size and route the gas supply line from the supply regulator to the area where the appliance is to be installed

per requirements outlined in the National Fuel Gas Code, NFPA 54—latest edition (USA) or CAN/CGA-B149.1—latest

edition (Canada).

The gas supply line should not be connected to the appliance until step 13. Connect the Gas Line (Page 42).

NOTE:

• All ﬁreplaces are factory-equipped with a ﬂexible gas line connector and 1/2” shutoff valve (Figure 31, Page 42).

• See Massachusetts Horizontal Vent Requirements for additional requirements for installations in the state of

Massachusetts in the USA.

• A pipe joint compound rated for gas should be used on the threaded joints. Ensure propane-resistant compounds

are used in propane applications. Be very careful that the pipe compound does not get inside the pipe.

• A sediment trap in the supply line as close as possible to the ﬁreplace is recommended.

• Check with the local building ofﬁcial for local code requirements (e.g., Are below grade penetrations of the gas

line allowed?, etc).

Installing Header shield (DRL3500 series models only)

Screw

Standoffs

Header Shield

Header

Shield

Step 1: Remove screw holding standoff to ﬁrebox, bend to 4” tall

(as seen above) and attach screw.

Step 2: Install the header shield by sliding it

into the slot in the standoffs.

Step 3: Fireboard standoff can be

secured to the capture screw holes.

Figure 10 - Installing Header Shield

La page charge ...

Superior Fireplaces DRL3500 Mode d'emploi

Marque: Superior Fireplaces

Modèle: DRL3500

Catégorie: Cheminées

Taper: Mode d'emploi

Ce manuel convient également à

DRL2000

Télécharger le PDF

rapport

dans d''autres langues

English: Superior Fireplaces DRL3500 Operating instructions

Superior Fireplaces DRL3500 Mode d'emploi

Ce manuel convient également à

Superior Fireplaces DRL3500 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents