Dell FE200 Manuel utilisateur

www.dell.com

support.dell.com

Dell™ PowerEdge™ Cluster FE100/FL100 and FE200/FL200

PLATFORM GUIDE

Guide des plates-formes

Plattform-Handbuch

Guía de plataforma

www.dell.com

support.dell.com

Dell™ PowerEdge™ Cluster FE100/FL100 and FE200/FL200

PLATFORM GUIDE

Notes, Notices, Cautions, and Warnings

Throughout this guide, blocks of text may be accompanied by an icon and printed in

bold type or in italic type. These blocks are notes, notices, cautions, and warnings,

and they are used as follows:

NOTE: A NOTE indicates important information that helps you make better use of

your computer system.

NOTICE: A NOTICE indicates either potential damage to hardware or loss

of data and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potentially hazardous situation which, if

not avoided, may result in minor or moderate injury.

WARNING: A WARNING indicates a potentially hazardous situation which,

if not avoided, could result in death or serious bodily injury.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of

Dell Computer Corporation is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, Dell OpenManage, PowerEdge, and PowerVault

are trademarks of Dell Computer Corporation; Microsoft, Windows, and Windows NT are regis-

tered trademarks of Microsoft Corporation; Intel is a registered trademark of Intel Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities

claiming the marks and names or their products. Dell Computer Corporation disclaims any propri-

etary interest in trademarks and trade names other than its own.

April 2001 P/N 6C403 Rev. A02

support.dell.com Dell PowerEdge Cluster Platform Guide 1-1

Dell™ PowerEdge™ Cluster

FE100/FL100 and FE200/FL200

Platform Guide

This guide provides the latest information on using Microsoft

®

Windows NT

®

Server 4.0, Enterprise Edition operating system and Windows

®

2000 Advanced

Server operating system for the following Dell PowerEdge Cluster FE100/FL100 and

FE200/FL200 products and components:

• PowerEdge Cluster FE100

— Supported servers: PowerEdge 1550, 2400, 2450, 2550, 4300, 4350, 4400,

6100, 6300, 6350, 6400, 6450, and 8450

— Storage system: Dell PowerVault™ 65xF

— Cluster interconnect: Intel

®

PRO/100+ Fast Ethernet controller, which can be

a peripheral component interconnect (PCI) card or an integrated controller, if

available

• PowerEdge Cluster FL100

— Supported servers: PowerEdge 1550, 2400, 2450, 2550, 4300, 4350, 4400,

6100, 6300, 6350, 6400, 6450, and 8450

— Storage system: PowerVault 65xF

— Cluster interconnect: Giganet cluster local area network (cLAN) high perfor-

mance, low-latency host adapter

• PowerEdge Cluster FE200

— Supported servers: PowerEdge 1550, 2400, 2450, 2550, 4300, 4350, 4400,

6300, 6350, 6400, 6450, and 8450

— Storage system: Dell PowerVault 660F/224F

— Cluster interconnect: Intel PRO/100+ Fast Ethernet controller, which can be

a PCI card or an integrated controller, if available

1-2 Dell PowerEdge Cluster Platform Guide

• PowerEdge Cluster FL200

— Supported servers: PowerEdge 1550, 2400, 2450, 2550, 4300, 4350, 4400,

6300, 6350, 6400, 6450, and 8450

— Storage system: PowerVault 660F/224F

— Cluster interconnect: Giganet cLAN high performance, low-latency host

adapter

See the section related to your cluster product for more information on supported

configurations. See also the Dell PowerEdge Cluster FE100/FL100 and FE200/FL200

Installation and Troubleshooting Guide for a detailed list of related documentation.

NOTE: Configurations not listed in this document are not certified or supported by

Dell or Microsoft.

Windows NT 4.0 Server, Enterprise Edition

The PowerEdge Cluster FE100/FL100 and FE200/FL200 support clustering on

Windows NT Server 4.0, Enterprise Edition. See the following sections for informa-

tion on supported configurations and service packs. See also the Dell PowerEdge

Cluster FE100/FL100 and FE200/FL200 Installation and Troubleshooting Guide for

installation instructions for hardware configurations using Windows NT Server 4.0,

Enterprise Edition.

PowerEdge Cluster FE100/FL100 and FE200/FL200

Homogeneous Configurations

Your PowerEdge Cluster FE100/FL100 and FE200/FL200 system supports the follow-

ing PowerEdge servers as cluster nodes in homogeneous pairs (same server) on

Windows NT 4.0, Enterprise Edition:

• PowerEdge 1550-1550

• PowerEdge 2400-2400

• PowerEdge 2450-2450

• PowerEdge 2550-2550

• PowerEdge 4300-4300

• PowerEdge 4350-4350

• PowerEdge 4400-4400

• PowerEdge 6300-6300

• PowerEdge 6350-6350

• PowerEdge 6400-6400

• PowerEdge 6450-6450

• PowerEdge 8450-8450

support.dell.com Dell PowerEdge Cluster Platform Guide 1-3

PowerEdge Cluster FE100/FL100 Heterogeneous

Configurations

Your PowerEdge Cluster FE100/FL100 system supports the following PowerEdge

servers as cluster nodes in heterogeneous pairs (mixed server models) with

Windows NT 4.0, Enterprise Edition:

• PowerEdge 2400-4300

• PowerEdge 2450-4350

• PowerEdge 4400-2400

• PowerEdge 4400-4300

• PowerEdge 6300-4300

• PowerEdge 6300-6100

• PowerEdge 6350-4350

• PowerEdge 6400-4400

• PowerEdge 6400-6300

• PowerEdge 6450-6350

• PowerEdge 8450-6350

• PowerEdge 8450-6450

NOTES: Both nodes must be configured with identical operating systems and service

packs, similar drivers (network interface controllers [NICs], Fibre Channel host bus

adapter [HBAs], and so on), utilities (Dell OpenManage™ system management soft-

ware, and so on), and Fibre Channel HBA basic input/output system (BIOS).

Heterogeneous server clusters (mixed server models) are not supported with

PowerEdge Cluster FE200/FL200 configurations running Windows NT 4.0.

Both optical and copper HBA connectors are supported in a storage area network

(SAN)-attached and SAN appliance-attached configuration. Copper HBA connectors

are supported in a direct-attached configuration.

Support for QLogic HBAs on Windows NT

Table 1-1 lists the QLogic HBAs and the PowerEdge servers on which they are sup-

ported for Windows NT cluster configurations. Table 1-2 lists the QLogic HBAs and

the PowerEdge servers on which they are supported for Windows NT FE200/FL200

cluster configurations. For PCI slot recommendations, see the section for your server

model on adding peripherals required for cluster nodes, found later in this document.

1-4 Dell PowerEdge Cluster Platform Guide

NOTE: All QLogic HBAs used in the cluster nodes must be the same model within the

cluster.

The supported drivers for the QLogic HBAs in Windows NT configurations are as

follows:

• For QLA-2100/ 33-MHz, version 7.05.08 or later

• For QLA-2200/ 33-MHz, version 7.05.08 or later

• For QLA-2200/ 66-MHz, version 7.05.08 or later

You can download the latest drivers from the Dell Web site at

http://support.dell.com.

Windows NT 4.0 Service Pack Support

Windows NT Service Pack 6a or later is recommended for PowerEdge Cluster

FE100/FL100 and FE200/FL200 systems.

Table 1-1. QLogic HBAs Supported for FE100 and FL100 on Windows NT

PowerEdge

Servers 1550 2400

2450 2550

4300/

4350 4400 6100

6300/

6350

6400/

6450 8450

QLogic

HBA

s

QLA-2100/

33-MHz

xxx

QLogic

HBA

s

QLA-2200/

33-MHz

xx x x x xx

QLogic

HBA

s

QLA-2200/

66-MHz

xx x x x x x x x

Table 1-2. QLogic HBAs Supported for FE200 and FL200 on Windows NT

PowerEdge

Servers 1550 2400

2450 2550

4300/

4350 4400

6300/

6350

6400/

6450 8450

QLogic

HBA

s

QLA-2200/

33-MHz

xx xxx x x

QLogic

HBA

s

QLA-2200/

66-MHz

xxxx xxx x x

support.dell.com Dell PowerEdge Cluster Platform Guide 1-5

Windows 2000 Advanced Server

The PowerEdge Cluster FE100/FL100 and FE200/FL200 support clustering on

Windows 2000 Advanced Server. See the following sections for information on sup-

ported configurations and service packs. See also the Dell PowerEdge Cluster

FE100/FL100 and FE200/FL200 Installation and Troubleshooting Guide for installation

instructions for hardware configurations using Windows 2000 Advanced Server.

PowerEdge Cluster FE100/FL100 and FE200/FL200

Homogeneous Configurations

Your PowerEdge Cluster FE100/FL100 and FE200/FL200 configuration supports the

following PowerEdge servers as cluster nodes in homogeneous pairs (same server)

with Windows 2000 Advanced Server:

• PowerEdge 1550-1550

• PowerEdge 2400-2400

• PowerEdge 2450-2450

• PowerEdge 2550-2550

• PowerEdge 4300-4300

• PowerEdge 4350-4350

• PowerEdge 4400-4400

• PowerEdge 6300-6300

• PowerEdge 6350-6350

• PowerEdge 6400-6400

• PowerEdge 6450-6450

• PowerEdge 8450-8450

NOTE: Heterogeneous server clusters (mixed server models) are not supported

with PowerEdge Cluster FE100/FL100 and FE200/FL200 configurations running

Windows 2000 Advanced Server.

Support for Qlogic HBAs on Windows 2000

Table 1-3 lists the QLogic HBAs and the PowerEdge servers on which they are sup-

ported for Windows 2000 cluster configurations. Table 1-4 lists the QLogic HBAs and

the PowerEdge servers on which they are supported for Windows 2000 FE200/FL200

cluster configurations. For PCI slot recommendations, see the section for your server

model on adding peripherals required for cluster nodes, found later in this document.

1-6 Dell PowerEdge Cluster Platform Guide

NOTE: All QLogic HBAs used in the cluster nodes must be the same model.

The supported drivers for the QLogic HBAs in Windows 2000 configurations are as

follows:

• For QLA-2100/ 33-MHz, version 7.05.08 or later

• For QLA-2200/ 33-MHz, version 7.05.08 or later

• For QLA-2200/ 66-MHz, version 7.05.08 or later

You can download the latest drivers from the Dell Web site at

http://support.dell.com.

Windows 2000 Service Pack Support

Microsoft Windows 2000 Service Pack 1 or later is recommended for PowerEdge

Cluster FE100/FL100 and FE200/FL200 systems.

Table 1-3. QLogic HBAs Supported for FE100/FL100 on Windows 2000

PowerEdge

Servers 1550 2400 2450 2550

4300/

4350 4400

6300/

6350

6400/

6450 8450

QLogic

HBA

s

QLA-2100/

33-MHz

xx

QLA-2200/

33-MHz

xx x x x x x

QLA-2200/

66-MHz

xxxx xxx xx

Table 1-4. QLogic HBAs Supported for FE200/FL200 on Windows 2000

PowerEdge

Servers 1550 2400

2450 2550

4300/

4350 4400

6300/

6350

6400/

6450 8450

QLogic

HBA

s

QLA-2200/

33-MHz

xx x x x x x

QLA-2200/

66-MHz

xxxx xxx xx

support.dell.com Dell PowerEdge Cluster Platform Guide 1-7

Guidelines for Adding Peripherals for

PowerEdge Cluster FE100/FL100 and

FE200/FL200 Configurations

The following sections describe adding peripherals for PowerEdge 1550, 2400, 2450,

2550, 4300, 4350, 4400, 6100, 6300, 6350, and 8450 cluster nodes.

WARNING: Hardware installation should be performed only by trained

service technicians. Before working inside the system, see the safety

instructions in your PowerEdge System Information document to avoid a

situation that could cause serious injury or death.

Peripherals for PowerEdge 1550 Cluster Nodes

The following list provides PCI slot assignment information for the system’s PCI

buses and HBAs.

• PCI buses

— PCI bus 1: PCI slot 1 is 64-bit, 66 MHz

— PCI bus 2: PCI slot 2 is 64-bit, 66 MHz

• HBAs

— You can install an HBA into any available PCI slot.

Peripherals for PowerEdge 2400 Cluster Nodes

The following list provides PCI slot assignment information for the system’s PCI

buses, HBAs, and the Dell OpenManage Remote Assistant Card 2 (DRAC 2).

• PCI buses

— PCI bus 0: PCI slots 1 through 5 are 64-bit, 33-MHz.

— PCI bus 1: PCI slot 6 is 32-bit, 33-MHz.

• HBAs

— For dual HBA configurations, Dell recommends installing the HBAs on sepa-

rate PCI buses to balance the load on the system.

• DRAC 2

— If you are currently using a DRAC 2 or plan to use one in the future, install it

in PCI slot 6.

1-8 Dell PowerEdge Cluster Platform Guide

Peripherals for PowerEdge 2450 Cluster Nodes

The following list provides PCI slot assignment information for the system’s PCI

buses and HBAs.

• PCI buses

— PCI bus 0: PCI slots 1 through 3 are 32-bit, 33-MHz.

• HBAs

— You can install HBAs in any available PCI slot.

Peripherals for PowerEdge 2550 Cluster Nodes

The following list provides PCI slot assignment information for the system’s PCI

buses.

• PCI buses

— PCI bus 0: PCI slots 1 through 3 are 64-bit, 33-MHz.

• HBAs

— You can install HBAs in any available PCI slot.

Peripherals for PowerEdge 4300/4350 Cluster Nodes

The following list provides PCI slot assignment information for the system’s PCI

buses, HBAs, and the DRAC 2.

• PCI buses

— PCI bus 0: PCI slots 1 through 3 are 32-bit, 33-MHz slots.

• HBAs

— For dual HBA configurations, Dell recommends installing the HBAs on sepa-

rate PCI buses to balance the load on the system.

• DRAC 2

— If you are currently using a DRAC 2 or plan to use one in the future, install it

in PCI slot 4.

Peripherals for PowerEdge 4400 Cluster Nodes

The following list provides PCI slot assignment information for the systems’s PCI

buses, HBAs, and the DRAC 2.

• PCI buses

— PCI bus 0: PCI slots 1 and 2 are 64-bit, 33/66-MHz.

— PCI bus 1: PCI slots 3 through 6 are 64-bit, 33-MHz.

— PCI bus 2: PCI slot 7 is 32-bit, 33-MHz.

support.dell.com Dell PowerEdge Cluster Platform Guide 1-9

• HBAs

— For dual HBA configurations, Dell recommends installing the HBAs on sepa-

rate PCI buses (PCI buses 1 and 2) to balance the load on the system.

• DRAC 2

— If you are currently using a DRAC 2 or plan to use one in the future, install it

in PCI slot 7.

Peripherals for PowerEdge 6100 Cluster Nodes

The following list provides PCI slot assignment information for the system’s PCI

buses and HBAs.

• PCI buses

— PCI bus 0: PCI slots 1 through 3 are 32-bit, 33-MHz slots.

— PCI bus 1: PCI slots 4 through 6 are 32-bit, 33-MHz slots.

• HBAs

— For dual HBA configurations, Dell recommends installing the HBAs on sepa-

rate PCI buses to balance the load on the system.

Peripherals for PowerEdge 6300 and 6350 Cluster Nodes

The following list provides PCI slot assignment information for the system’s PCI

buses, HBAs, and the DRAC 2.

• PCI buses

— PCI bus 0: PCI slots 1 through 3 are 32-bit, 33-MHz.

— PCI bus 1: PCI slots 4 through 7 are 64-bit, 33-MHz.

• HBAs

— For dual HBA configurations, Dell recommends installing the HBAs on sepa-

rate PCI buses to balance the load on the system.

• DRAC 2

— If you are currently using a DRAC 2 or plan to use one in the future, install it

in PCI slot 3.

1-10 Dell PowerEdge Cluster Platform Guide

Peripherals for PowerEdge 6400 and 6450 Cluster Nodes

The following list provides PCI slot assignment information for the system’s PCI

buses, HBAs, and the DRAC 2.

• PCI buses

— PCI bus 0: PCI slot 1 is 32-bit, 33-MHz.

— PCI bus 1: PCI slots 2 through 5 are 64-bit, 33-MHz.

— PCI bus 2: PCI slots 6 and 7 are 64-bit, 33/66-MHz.

• HBAs

— For dual HBA configurations, Dell recommends installing the HBAs on sepa-

rate PCI buses (PCI buses 1 and 2) to balance the load on the system.

• DRAC 2

— If you are currently using a DRAC 2 or plan to use one in the future, install it

in PCI slot 1.

Peripherals for PowerEdge 8450 Cluster Nodes

The following list provides PCI slot assignment information for the system’s PCI

buses, RAID controllers, HBAs, and the DRAC 2.

• PCI buses

— PCI bus 0: PCI slot 1 and 2 are 64-bit, 33-MHz.

— PCI bus 1: PCI slots 3 through 6 are 64-bit, 33-MHz.

— PCI bus 2: PCI slots 7 and 8 are 64-bit, 33/66-MHz.

— PCI bus 3: PCI slots 9 and 10 are 64-bit, 33/66-MHz.

• RAID controllers

— Install the RAID controller for the server’s internal drives in PCI slot 1.

• HBAs

— For dual HBA configurations, Dell recommends installing the HBAs on sepa-

rate PCI buses (PCI buses 2 and 3) to balance the load on the system.

• DRAC 2

— If you are currently using a DRAC 2 or plan to use one in the future, install it

in PCI slot 2.

www.dell.com

support.dell.com

Dell™ PowerEdge™ Cluster FE100/FL100 et FE200/FL200

GUIDE DES PLATES-FORMES

Remarques, avis, précautions et avertissements

Dans ce guide, certains blocs de texte sont accompagnés d'une icône et imprimés en

caractères gras ou en italique. Ces blocs sont des remarques, des avis, des précau-

tions et des avertissements utilisés comme suit :

REMARQUE : Une REMARQUE indique des informations importantes qui vous aident

à utiliser votre système informatique au mieux.

AVIS : Un AVIS vous avertit d’un risque de dommage matériel ou de perte

de données et vous indique comment éviter le problème.

PRÉCAUTION : Une PRÉCAUTION vous avertit d’une situation qui, si elle

n'est pas évitée, peut entraîner des blessures plus ou moins graves.

AVERTISSEMENT : Un AVERTISSEMENT vous avertit d’une situation qui, si

elle n'est pas évitée, peut provoquer la mort ou des blessures sérieuses.

____________________

Les informations contenues dans ce document sont sujettes à modification sans préavis.

Toute reproduction, sous quelque forme que ce soit, sans l'autorisation écrite de

Dell Computer Corporation, est strictement interdite.

Marques utilisées dans ce texte†: Dell, le logo DELL, Dell OpenManage, PowerEdge et PowerVault

sont des marques de Dell Computer Corporation ; Microsoft, Windows et Windows NT sont des

marques déposées de Microsoft Corporation ; Intel est une marque déposée de Intel Corporation.

D'autres marques et noms commerciaux peuvent être utilisés dans ce document pour faire réfé-

rence aux entités se réclamant de ces marques et de ces noms ou à leurs produits. Dell Computer

Corporation dénie tout intérêt propriétaire vis-à-vis des marques et des noms commerciaux autres

que les siens.

Avril 2001 P/N 6C403 Rév. A02

support.dell.com Guide des plates-formes Dell PowerEdge Cluster 2-1

Guide des plates-formes

Dell™ PowerEdge™ Cluster

FE100/FL100 et FE200/FL200

Ce guide présente les informations les plus récentes concernant l'utilisation du sys-

tème d'exploitation Microsoft

®

Windows NT

®

Server 4.0, Enterprise Edition et du

système d'exploitation Windows

®

2000 Advanced Server pour les produits et compo-

sants Dell PowerEdge Cluster FE100/FL100 et FE200/FL200 suivants :

• PowerEdge Cluster FE100

— Serveurs pris en charge : PowerEdge 1550, 2400, 2450, 2550, 4300, 4350,

4400, 6100, 6300, 6350, 6400, 6450 et 8450

— Système de stockage : Dell PowerVault™ 65xF

— Interconnexion de clusters : Contrôleur Intel

®

PRO/100+ Fast Ethernet, pou-

vant être une carte PCI (Peripheral Component Interconnect [interconnexion

de composants périphériques]) ou un contrôleur intégré, si celui-ci est

disponible

• PowerEdge Cluster FL100

— Serveurs pris en charge : PowerEdge 1550, 2400, 2450, 2550, 4300, 4350,

4400, 6100, 6300, 6350, 6400, 6450 et 8450

— Système de stockage : PowerVault 65xF

— Interconnexion de clusters : Adaptateur à l'hôte à faible latence et à hautes

performances, en réseau cLAN (cluster Local Area Network [cluster de

réseau local]) Giganet

• PowerEdge Cluster FE200

— Serveurs pris en charge : PowerEdge 1550, 2400, 2450, 2550, 4300, 4350,

4400, 6300, 6350, 6400, 6450 et 8450

— Système de stockage : Dell PowerVault 660F/224F

— Interconnexion de clusters : Contrôleur Intel PRO/100+ Fast Ethernet, pou-

vant être une carte PCI ou un contrôleur intégré, si celui-ci est disponible

2-2 Guide des plates-formes Dell PowerEdge Cluster

• PowerEdge Cluster FL200

— Serveurs pris en charge : PowerEdge 1550, 2400, 2450, 2550, 4300, 4350,

4400, 6300, 6350, 6400, 6450 et 8450

— Système de stockage : PowerVault 660F/224F

— Interconnexion de clusters : Adaptateur à l'hôte à faible latence et à hautes

performances Giganet cLAN

Reportez-vous à la section traitant de votre produit cluster pour de plus amples infor-

mations sur les configurations prises en charge. Reportez-vous également au Guide

d'installation et de dépannage des Dell PowerEdge Cluster FE100/FL100 et

FE200/FL200 pour obtenir une liste détaillée de documents connexes.

REMARQUE : Les configurations ne figurant pas dans ce document ne sont pas certi-

fiées ou prises en charge par Dell ou par Microsoft.

Windows NT 4.0 Server, Enterprise Edition

Les systèmes PowerEdge Cluster FE100/FL100 et FE200/FL200 prennent en charge

la gestion de clusters sous Windows NT Server 4.0, Enterprise Edition. Reportez-vous

aux sections suivantes pour de plus amples informations sur les configurations et les

service packs pris en charge. Consultez également le Guide d'installation et de dépan-

nage de Dell PowerEdge Cluster FE100/FL100 et FE200/FL200 pour obtenir des ins-

tructions sur l'installation des configurations matérielles qui exécutent Windows NT

Server 4.0, Enterprise Edition.

Configurations homogènes des PowerEdge Cluster

FE100/FL100 et FE200/FL200

Votre système PowerEdge Cluster FE100/FL100 ou FE200/FL200 prend en charge

les serveurs PowerEdge ci-après en tant que nœuds de cluster en paires homogènes

(même serveur) sous Windows NT 4.0, Enterprise Edition :

• PowerEdge 1550-1550

• PowerEdge 2400-2400

• PowerEdge 2450-2450

• PowerEdge 2550-2550

• PowerEdge 4300-4300

• PowerEdge 4350-4350

• PowerEdge 4400-4400

• PowerEdge 6300-6300

• PowerEdge 6350-6350

• PowerEdge 6400-6400

support.dell.com Guide des plates-formes Dell PowerEdge Cluster 2-3

• PowerEdge 6450-6450

• PowerEdge 8450-8450

Configurations hétérogènes de PowerEdge Cluster

FE100/FL100

Votre système PowerEdge Cluster FE100/FL100 prend en charge les serveurs

PowerEdge ci-après en tant que nœuds de cluster en paires hétérogènes (différents

modèles de serveurs) avec Windows NT 4.0, Enterprise Edition :

• PowerEdge 2400-4300

• PowerEdge 2450-4350

• PowerEdge 4400-2400

• PowerEdge 4400-4300

• PowerEdge 6300-4300

• PowerEdge 6300-6100

• PowerEdge 6350-4350

• PowerEdge 6400-4400

• PowerEdge 6400-6300

• PowerEdge 6450-6350

• PowerEdge 8450-6350

• PowerEdge 8450-6450

REMARQUES : Les deux nœuds doivent être configurés avec les mêmes systèmes

d'exploitation et service packs, des pilotes comparables (NIC [Network Interface Con-

troller (contrôleur d'interface de réseau)], adaptateurs HBA [Host Bus Adapter (adap-

tateur de bus à l'hôte)] Fibre Channel, etc.), les mêmes utilitaires (logiciel de gestion

de système Dell OpenManage™, etc.) et le même BIOS (Basic Input/Output System

[système d'entrées/sorties de base]) HBA Fibre Channel.

Les clusters de serveurs hétérogènes (modèles de serveurs mixtes) ne sont pas pris

en charge avec les configurations PowerEdge Cluster FE200/FL200 qui exécutent

Windows NT 4.0.

Les connecteurs HBA [Host Bus Adapter (adaptateur de bus à l'hôte)], qu'ils soient

optiques ou en cuivre, sont pris en charge dans une configuration associée à un SAN

[Storage Area Network (réseau de stockage)] et sur un appareil SAN. Les connecteurs

HBA en cuivre sont pris en charge dans une configuration associée directement.

Prise en charge des HBA QLogic sous Windows NT

Le tableau 2-1 présente les HBA QLogic et les serveurs PowerEdge sur lesquels ces

adaptateurs HBA sont pris en charge pour les configurations de cluster Windows NT.

Le tableau 2-2 présente les adaptateurs HBA QLogic et les serveurs PowerEdge sur

lesquels ces adaptateurs sont pris en charge pour les configurations de cluster

Windows NT FE200/FL200. Pour les recommandations concernant les logements

2-4 Guide des plates-formes Dell PowerEdge Cluster

PCI, consultez la section de votre modèle serveur relative à l'ajout des périphériques

requis pour les nœuds de cluster, figurant plus loin dans ce document.

REMARQUE : Tous les adaptateurs HBA QLogic utilisés dans les nœuds du cluster

doivent être du même modèle.

Les pilotes pris en charge pour les adaptateurs HBA QLogic sous les configurations

Windows NT sont les suivants :

• Pour QLA-2100/ 33 MHz, version 7.05.08 ou ultérieure

• Pour QLA 2200/ 33 MHz, version 7.05.08 ou ultérieure

• Pour QLA 2200/ 66 MHz, version 7.05.08 ou ultérieure

Vous pouvez télécharger les pilotes les plus récents à partir du site Web de Dell à

l'adresse http://support.dell.com.

Prise en charge du service pack de Windows NT 4.0

Windows NT Service Pack 6a ou version ultérieure est recommandé pour les systè-

mes PowerEdge Cluster FE100/FL100 et FE200/FL200.

Tableau 2-1. Adaptateurs HBA QLogic pris en charge pour FE100 et FL100 sous

Windows NT

Serveurs

PowerEdge 1550 2400

2450 2550

4300/

4350 4400 6100

6300/

6350

6400/

6450 8450

HBA

QLogic

QLA 2100/

33 MHz

xxx

HBA

QLogic

QLA 2200/

33 MHz

xx x x x xx

HBA

QLogic

QLA 2200/

66 MHz

xx x x x x x x x

Tableau 2-2. HBA QLogic pris en charge pour FE200 et FL200 sous Windows NT

Serveurs

PowerEdge 1550 2400

2450 2550

4300/

4350 4400

6300/

6350

6400/

6450 8450

HBA

QLogic

QLA 2200/

33 MHz

xx xxx x x

HBA

QLogic

QLA 2200/

66 MHz

xxxx xxx x x

La page charge ...

Dell FE200 Manuel utilisateur

Ce manuel convient également à

Dell FE200 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents