TP-LINK Deco BE65 BE11000 Whole Home Mesh WiFi 7 System Mode d'emploi

Marque: TP-LINK

Modèle: Deco BE65 BE11000 Whole Home Mesh WiFi 7 System

Taper: Mode d'emploi

Deco BE65

The Ultimate 10 Gbps Connectivity

User Guide

BE11000 Whole Home

Mesh Wi-Fi 7 System

Contents

About This Guide ···················································· 1

Appearance ······························································· 2

Set Up Your Deco ··················································· 3

Troubleshooting ······················································ 8

Authentication ·························································· 9

About This Guide

This guide provides a brief introduction to BE11000 Whole Home Mesh Wi-Fi 7 System and regulatory information.

Features available in Deco may vary by model and software version. Deco availability may also vary by region or ISP. All images, steps, and descriptions

in this guide are only examples and may not reect your actual Deco experience.

Conventions

In this guide, the following conventions are used:

Convention Description

Deco Stands for Deco Whole Home Mesh Wi-Fi System/

Unit.

Underline Hyperlinks are in teal and underlined. You can click to

redirect to a website or a specic section.

Teal

Key information appears in teal, including

management page text such as menus, items,

buttons and so on.

Note: Ignoring this type of note might result in a malfunction

or damage to the device.

Tips: Indicates important information that helps you make

better use of your device.

More Info

• Specic product information can be found on the product page at

https://www.tp-link.com.

• A Technical Community is provided for you to discuss our products

at https://community.tp-link.com.

• Our Technical Support contact information can be found at the

Help center of the Deco app and the Contact Technical Support

page at https://www.tp-link.com/support.

Speed/Coverage/Device Quantity Disclaimer

Maximum wireless signal rates are the physical rates derived from IEEE

Standard 802.11 specications. Actual wireless data throughput and

wireless coverage, and quantity of connected devices are not guaranteed

and will vary as a result of network conditions, client limitations, and

environmental factors, including building materials, obstacles, volume and

density of trac, and client location.

MU-MIMO Disclaimer

Use of MU-MIMO requires clients to also support MU-MIMO.

IoT Compatibility Disclaimer

IoT compatibility refers only to smart devices that can be controlled via the

Deco app. Other wireless devices can still connect to Deco for normal Wi-Fi

use.

Seamless Roaming Disclaimer

Clients need to support 802.11k/v/r and may require additional set up.

Performance may vary depending on the client device.

HomeShield Disclaimer

HomeShield includes the Free Basic Plan. Fees apply for the Pro Plan. Visit

tp-link.com/homeshield for more information.

Appearance

Each Deco has an LED that changes color according to its status, a WPS button, two 2.5 Gbps WAN/LAN ports, a 10 Gbps WAN/LAN port, a 10 Gbps

RJ45/SFP+ WAN/LAN Combo port, a USB 3.0 port, a power slot, and a Reset button.

See the explanation below:

Tip: The product label can be found at the bottom of the product.

Pulse Yellow:

Deco is resetting.

Solid Yellow:

Deco is starting up.

Pulse Blue:

Deco is ready for setup.

Solid Blue:

Deco is setting up.

Pulse Green:

Deco is upgrading rmware.

Solid Green:

Deco is all set up and connected.

Pulse Red:

The satellite Deco is disconnected

from the main Deco.

Solid Red:

Deco has an issue.

Press this WPS button, and immediately press the WPS button

on your client device to start the WPS process.

For connecting a USB storage device to Deco.

For connecting Deco to your modem, the Ethernet outlet,

or for other internet services.

For connecting Deco to the power socket via the provided power adapter.

4× 2.5 Gbps WAN/LAN Ports

WPS Button

Power Slot

Press for 1 second and release to reset Deco to factory default settings. The light

changing from pulsing yellow to solid yellow indicated a successful reset.

Reset Button

1× USB 3.0 Port

Set Up Your Deco

First let's start by setting up the Deco network. Get the TP-Link Deco app for iOS or Android, then follow the app to walk through the setup.

1. Get the Deco app

Scan the QR code below or go to Google

Play or the App Store to download the Deco

app. Install the app on your Android or iOS

smartphone or tablet.

2. Log in or sign up with TP-Link ID

Open the app and log in with your TP-Link ID. If

you don’t have a TP-Link ID, create one rst.

Note: If you forgot your login password, tap Forgot Password?.

The app will help you reset your password.

3. Select your Deco model

Search for and select your Deco model. If

you have more than one Deco model, tap the

question below the search box to check how

to maximize the overall network.

4. Plug in your Deco

Power o your modem. Connect your Deco to

the modem and power them both on.

If you don't have a modem, connect your

Deco directly to the Ethernet outlet.

5. Wait until Deco's LED pulses blue

Wait until your Deco's LED pulses blue, then

your phone/tablet will connect to the Deco's

default Wi-Fi automatically.

6. Specify your Deco's location

Select or custom a location for your Deco.

The location will be used as the name of your

Deco.

9. Create your MLO network

Set a network name and a password. The MLO

network enables Wi-Fi 7 clients to connect to

multiple bands simultaneously.

8. Create your Wi-Fi network

Set a network name and a password. These

will be the name and password you use to

connect your devices to Wi-Fi.

7. Connect your Deco to the internet

Select the internet connection type and enter

the information. If you are not sure, contact

your internet service provider.

10. Keep your Deco up-to-date

Set auto update time. This allows your Deco

to automatically update to the latest rmware

which provides better network experience.

12. Setup complete

Your Deco network is now up. You can connect

your devices to the Deco network. Plug

in the other included Decos, and they will

automatically join the network within 2 minutes.

11. Connect to your Wi-Fi network

Connect your phone/tablet to the Deco's

Wi-Fi.

13. Add more Decos

Plug in the other included Decos, and they will

automatically join the network within 2 minutes.

Troubleshooting

Solutions to common problems during setup or use are provided here for reference. Follow the steps and the provided link below to diagnose and solve

problems you might experience with your Deco.

If problems still exist, contact us: https://www.tp-link.com/support

Q1. What should I do if I fail to congure the main Deco and get stuck on “We couldn't nd Deco”?

Refer to the guide https://www.tp-link.com/support/faq/2239/ or follow the video https://youtu.be/2HYuEYS9XJM

Q2. What should I do if I fail to congure the satellite Deco and get stuck on “We couldn't nd another Deco”?

Refer to the guide https://www.tp-link.com/support/faq/1447/ or follow the video https://youtu.be/iVgDzoo16T4

Q3. What should I do if I fail to congure the main Deco and get stuck on “Testing Internet Connection”?

Refer to the video https://youtu.be/OSUrGdWH-i0

Q4. What should I do if my wireless devices cannot connect to Deco?

Refer to the guide https://www.tp-link.com/support/faq/2718/

Q5. What should I do if Deco suddenly lost internet access?

Refer to the guide https://www.tp-link.com/support/faq/1454/

Q6. How can I nd a suitable spot for my Deco?

Refer to the guide https://www.tp-link.com//support/faq/1446/

Q7. What can I do if the Deco app isn't working properly?

Refer to the guide https://www.tp-link.com/support/faq/1456/

Authentication

FCC Compliance Information Statement

Product Name: BE11000 Whole Home Mesh Wi-Fi 7 System

Model Number: Deco BE65

Component Name Model

I.T.E Power Supply T120330-2B4

Responsible party:

TP-Link USA Corporation

Address: 10 Mauchly, Irvine, CA 92618

Website: http://www.tp-link.com/us/

Tel: +1 626 333 0234

Fax: +1 909 527 6804

E-mail: [email protected]om

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the

equipment.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications

could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be

co-located or operating in conjunction with any other antenna or transmitter.

To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter

must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with

any other antenna or transmitter.

FCC regulations restrict operation of this device to indoor use only. The operation of this device is prohibited on oil platforms, cars, trains, boats, and

aircraft, except that operation of this device is permitted in large aircraft while flying above 10000 feet. Operation of transmitters in the 5.925-7.125

GHz band is prohibited for control of or communications with unmanned aircraft systems.

We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards,

FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.

Issue Date: 2023-02-23

FCC Compliance Information Statement

Product Name: I.T.E POWER SUPPLY

Model Number: T120330-2B4

Responsible party:

TP-Link USA Corporation

Address: 10 Mauchly, Irvine, CA 92618

Website: http://www.tp-link.com/us/

Tel: +1 626 333 0234

Fax: +1 909 527 6804

E-mail: [email protected]om

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the

equipment.

FCC regulations restrict operation of this device to indoor use only. The operation of this device is prohibited on oil platforms, cars, trains, boats, and

aircraft, except that operation of this device is permitted in large aircraft while flying above 10000 feet. Operation of transmitters in the 5.925-7.125

GHz band is prohibited for control of or communications with unmanned aircraft systems.

We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards,

FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.

Issue Date: 2023-02-23

Canadian Compliance Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux

deux conditions suivantes :

1. l’appareil ne doit pas produire de brouillage;

2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, meme si le brouillage est susceptible d’en compromettre le

fonctionnement.

Caution:

The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile

satellite systems;

DFS (Dynamic Frequency Selection) products that operate in the bands 5250- 5350 MHz, 5470-5600MHz, and 5650-5725MHz.

ISED regulations restrict operation of this device to indoor use only. The operation of this device is prohibited on oil platforms, cars, trains, boats, and

aircraft, except that operation of this device is permitted in large aircraft while flying above 10000 feet. Operation of transmitters in the 5.925-7.125

GHz band is prohibited for control of or communications with unmanned aircraft systems.

Avertissement:

Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utilisation à l’intérieur afin de réduire les risques de

brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;

Les produits utilisant la technique d’atténuation DFS (sélection dynamique des fréquences) sur les bandes 5250- 5350 MHz, 5470-5600MHz et

5650-5725MHz.

Les réglementations ISED limitent le fonctionnement de cet appareil à une utilisation en intérieur uniquement. L’utilisation de cet appareil est interdite

sur les plates-formes pétrolières, les voitures, les trains, les bateaux et les avions, sauf que l’utilisation de cet appareil est autorisée dans les avions

long courrier en vol au-dessus de 10 000 pieds. L’exploitation d’émetteurs dans la bande 5,925-7,125 GHz est interdite pour le contrôle ou les

communications avec des systèmes d’avions sans pilote.

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated

with minimum distance 20cm between the radiator & your body.

Déclaration d’exposition aux radiations:

Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être

installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.

ISED regulations restrict operation of this device to indoor use only. The operation of this device is prohibited on oil platforms, cars, trains, boats, and

aircraft, except that operation of this device is permitted in large aircraft while flying above 10000 feet. Operation of transmitters in the 5.925-7.125

GHz band is prohibited for control of or communications with unmanned aircraft systems.

Les réglementations ISED limitent le fonctionnement de cet appareil à une utilisation en intérieur uniquement. L’utilisation de cet appareil est interdite

sur les plates-formes pétrolières, les voitures, les trains, les bateaux et les avions, sauf que l’utilisation de cet appareil est autorisée dans les avions

long courrier en vol au-dessus de 10000 pieds. L’exploitation d’émetteurs dans la bande 5,925-7,125 GHz est interdite pour le contrôle ou les

communications avec des systèmes d’avions sans pilote.

Industry Canada Statement

CAN ICES-3 (B)/NMB-3(B)

Korea Warning Statements:

당해 무선설비는 운용중 전파혼신 가능성이 있음.

NCC Notice & BSMI Notice:

注意！

取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。

低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。

前述合法通信，指依電信管理法規定作業之無線電通信。

低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

應避免影響附近雷達系統之操作。

安全諮詢及注意事項

• 請按照本產品注明的電源類型使用本產品。

• 清潔本產品之前請先切斷電源。請勿使用液體、噴霧清潔劑或濕布進行清潔。

• 注意防潮，請勿將水或其他液體潑灑到本產品上。

• 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。

• 請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。

• 不要私自拆開機殼或自行維修，如產品有故障請與原廠或代理商聯繫。

限用物質含有情況標示聲明書

設備名稱：

Equipment name:

BE11000 Whole Home Mesh Wi-Fi 7 System

型號（型式）：

Type designation (Type)

Deco BE65

單元

Unit

限用物質及其化學符號

Restricted substances and its chemical symbols

鉛

Lead

(Pb)

汞

Mercury

(Hg)

鎘

Cadmium

(Cd)

六價鉻

Hexavalent

chromium

(Cr+6)

多溴聯苯

Polybrominated

biphenyls

(PBB)

多溴二苯醚

Polybrominated

diphenyl ethers

(PBDE)

PCB ○ ○ ○ ○ ○ ○

外殼 ○ ○ ○ ○ ○ ○

電源供應器 −○ ○ ○ ○ ○

其他及其配件 −○ ○ ○ ○ ○

備考1.超出0.1wt%”及“超出0.01wt%”系指限用物質之百分比含量超出百分比含量基準值。

Note 1：“Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the

reference percentage value of presence condition.

備考2.“○”系指該項限用物質之百分比含量未超出百分比含量基準值。

Note 2：“○” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.

備考3.“−”系指該項限用物質為排除項目。

Note 3：The “−” indicates that the restricted substance corresponds to the exemption.

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам,

що передбачені чинними законодавчими актами України.

Safety Information

• Keep the device away from water, fire, humidity or hot environments.

• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.

• Do not use damaged charger or USB cable to charge the device.

• Do not use any other chargers than those recommended.

• Do not use the device where wireless devices are not allowed.

• Adapter shall be installed near the equipment and shall be easily accessible.

• Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don’t

hesitate to contact us.

• Operating Temperature: 0°C~40°C (32°F~104°F)

• This product uses radios and other components that emit electromagnetic fields. Electromagnetic fields and magnets may interfere with pacemakers

and other implanted medical devices. Always keep the product and its power adapter more than 15 cm (6 inches) away from any pacemakers or

other implanted medical devices. If you suspect your product is interfering with your pacemaker or any other implanted medical device, turn off

your product and consult your physician for information specific to your medical device.

Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to

improper use of the device. Please use this product with care and operate at your own risk.

Explanation of the symbols on the product label

Symbol Explanation

DC Voltage

Alternating current

Caution

Operator’s manual

Indoor use only

Polarity of d.c. power connector

Energy efficiency marking

Class II equipment

RECYCLING

This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means

that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to

minimize its impact on the environment.

User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new

electrical or electronic equipment.

TP-LINK Deco BE65 BE11000 Whole Home Mesh WiFi 7 System Mode d'emploi

Marque: TP-LINK

Modèle: Deco BE65 BE11000 Whole Home Mesh WiFi 7 System

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: TP-LINK Deco BE65 BE11000 Whole Home Mesh WiFi 7 System User guide

TP-LINK Deco BE65 BE11000 Whole Home Mesh WiFi 7 System Mode d'emploi

TP-LINK Deco BE65 BE11000 Whole Home Mesh WiFi 7 System Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents