Briggs & Stratton 1934 Manuel utilisateur

Marque: Briggs & Stratton

Modèle: 1934

Catégorie: Accessoires pour véhicules automobiles

Taper: Manuel utilisateur

Ce manuel convient également à

Manual No. 194947GS

Revision 2 (09/16/2004)

Model / Modèle / Modelo

PRO8000

01934

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON,WISCONSIN, U.S.A.

Owner’s Manual

Questions? Help is just a

moment away!

Call: Generator Helpline -

1-800-743-4115 M-F 8-5 CT

Manuel de l'utilisateur

Vous avez des questions?

Vous n'avez pas besoin d'aller loin

pour trouver de l'aide!

Appelez: Ligne d'assistance de

Générateur - 1-800-743-4115

M-F 8-5 CT

Manual del Propietario

Preguntas? La ayuda es justa un

momento lejos!

Llamada: Generador Helpline -

1-800-743-4115 M-F 8-5 CT

Model may vary slightly

from that shown

BSPP Generator

TABLE OF CONTENTS

Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Know Your Generator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-16

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

EQUIPMENT

DESCRIPTION

Read this manual carefully and become familiar

with your generator. Know its applications, its

limitations and any hazards involved.

This generator is an engine–driven, revolving field,

alternating current (AC) generator. It was designed to supply

electrical power for operating compatible electrical lighting,

appliances, tools and motor loads.The generator’s revolving

field is driven at about 3,600 rpm by the engine.

This generator incorporates GFCI (Ground Fault Circuit

Interrupter) outlet protection and has its neutral bonded

to ground to pass OSHA inspections on job sites.This

generator will not function when connected to a transfer

switch since the home or building main breaker box also

has a neutral bonded to ground.When both the generator

and the home or building breaker box contains a neutral

bonded to ground, the generators GFCI will open and no

outlets will function.

CAUTION! DO NOT exceed the generator’s

wattage/amperage capacity. See “Don’t Overload

Generator”.

Every effort has been made to ensure that information in

this manual is accurate and current. However, we reserve

the right to change, alter or otherwise improve the product

and this document at any time without prior notice.

The Emission Control System for this generator is warranted

for standards set by the Environmental Protection Agency. For

warranty information refer to the engine owner’s manual.

SAFETY RULES

This is the safety alert symbol. It is used to

alert you to potential personal injury hazards.

Obey all safety messages that follow this

symbol to avoid possible injury or death.

The safety alert symbol ( ) is used with a signal word

(DANGER, CAUTION,WARNING), a pictorial and/or a

safety message to alert you to hazards. DANGER indicates

a hazard which, if not avoided, will result in death or

serious injury. WARNING indicates a hazard which, if not

avoided, could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, might

result in minor or moderate injury. CAUTION, when used

without the alert symbol, indicates a situation that could

result in equipment damage. Follow safety messages to

avoid or reduce the risk of injury or death.

Hazard Symbols and Meanings

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

WARNING

Fire

Explosion

Toxic Fumes

Hot Surface

Electrical Shock

Electrocution

Electrical Shock

Explosive Pressure

Chemical Burn

• Removing the neutral bond could result in death, bodily injury

and/or property damage.

DO NOT remove the neutral bond.

WARNING

BSPP Generator

• DO NOT allow any open flame, spark, heat, or lit cigarette

during and for several minutes after charging a battery.

• Wear protective goggles, rubber apron, and rubber gloves.

Storage batteries give off explosive hydrogen gas

during recharging.

Hydrogen gas stays near battery for a long time

after battery has been charged.

Slightest spark will ignite hydrogen and cause

explosion.

You can be blinded or severely injured.

Battery electrolyte fluid contains acid and is

extremely caustic.

Contact with battery fluid will cause severe

chemical burns.

DANGER

• When using generator for backup power, notify utility

company. Use approved transfer equipment to isolate

generator from electric utility.

• Use a ground fault circuit interrupter (GFCI) in any damp or

highly conductive area, such as metal decking or steel work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain.

• DO NOT handle generator or electrical cords while standing

in water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator.

Generator produces powerful voltage.

Failure to isolate generator from power utility

can result in death or injury to electric utility

workers due to backfeed of electrical energy.

DANGER

• This generator does not meet U. S. Coast Guard Regulation

33CFR-183 and should not be used on marine applications.

• Failure to use the appropriate U. S. Coast Guard approved

generator could result in bodily injury and/or property

damage.

WARNING

WHEN ADDING OR DRAINING FUEL

• Turn generator OFF and let it cool at least 2 minutes before

removing fuel cap. Loosen cap slowly to relieve pressure in

tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank.Allow space for fuel expansion.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap and air cleaner are in place.

• DO NOT crank engine with spark plug removed.

• If fuel spills, wait until it evaporates before starting engine.

WHEN OPERATING EQUIPMENT

• Do not tip engine or equipment at angle which causes fuel to

spill.

• This generator is not for use in mobile equipment or marine

applications.

WHEN TRANSPORTING OR REPAIRING

EQUIPMENT

• Transport/repair with fuel tank EMPTY or with fuel shutoff

valve OFF.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL

IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers or other appliances that have pilot light or other

ignition source because they can ignite fuel vapors.

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WARNING

• Operate generator ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes or other openings.

• DO NOT operate generator inside any building or enclosure,

including the generator compartment of a recreational vehicle (RV).

Running generator gives off carbon monoxide,

an odorless, colorless, poison gas.

Breathing carbon monoxide will cause nausea,

fainting or death.

DANGER

BSPP Generator

• DO NOT tamper with governed speed. Generator supplies

correct rated frequency and voltage when running at governed

speed.

• DO NOT modify generator in any way.

Excessively high operating speeds increase risk of injury

and damage to generator.

Excessively low speeds impose a heavy load.

CAUTION

• See “Don’t Overload Generator”.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator

before stopping generator.

Exceeding generators wattage/amperage capacity can

damage generator and/or electrical devices connected

to it.

CAUTION

• Use generator only for intended uses.

• If you have questions about intended use, ask dealer or call

1-800-743-4115.

• Operate generator only on level surfaces.

• DO NOT expose generator to excessive moisture, dust, dirt,

or corrosive vapors.

• DO NOT insert any objects through cooling slots.

• If connected devices overheat, turn them off and disconnect

them from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

Improper treatment of generator can damage it and

shorten its life.

CAUTION

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

GENERATOR

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Unintentional sparking can result in fire or

electric shock.

WARNING

• DO NOT touch hot surfaces.

• Allow equipment to cool before touching.

• The generator must be at least 5 feet from structures having

combustible walls and/or other combustible materials.

• Keep at least 3 feet of clearance on all sides of generator for

adequate cooling, maintenance and servicing.

• In the State of California a spark arrester is required by law

(Section 4442 of the California Public Resources Code). Other

states may have similar laws. Federal laws apply on federal

lands. If you equip the muffler with a spark arrester, it must be

maintained in effective working order.

Running engines produce heat.Temperature of

muffler and nearby areas can reach or exceed

150°F (65°C).

Severe burns can occur on contact.

Combustible debris, such as leaves, grass, brush,

ect. can catch fire.

WARNING

BSPP Generator

KNOW YOUR GENERATOR

Read this owner’s manual and safety rules before operating your generator.

Compare the illustrations with your generator, to familiarize yourself with the locations of various controls and

adjustments. Save this manual for future reference.

12 Volt DC Receptacle — Use this receptacle with battery

charge cables to charge a 12 Volt battery.

120 Volt AC, 20 Amp Duplex Receptacles — May be used to

supply electrical power for the operation of 120Volt AC, 20 Amp,

single phase, 60 Hz electrical lighting, appliance, tool and motor loads.

120 Volt AC, 30 Amp Locking Receptacle — May be used to

supply electrical power for the operation of 120Volt AC, 30 Amp,

single phase, 60 Hz electrical lighting, appliance, tool and motor

loads.

120/240 Volt AC, 30 Amp Locking Receptacle — May be

used to supply electrical power for the operation of 120 and/or

240 Volt AC, 30 Amp, single phase, 60 Hz electrical lighting,

appliance, tool and motor loads.

Air Cleaner — Uses a dry type filter element and foam

pre–cleaner to limit the amount of dirt and dust sucked into the

engine.

Choke Lever — Used when starting a cold engine.

Circuit Breakers (AC) — Push to reset circuit breakers are

provided to protect the generator against electrical overload.

Data Tag – Provides model, revision and serial number of

generator. Please have these readily available if calling for

assistance.

Fuel Tank — Capacity of seven (7) U.S. gallons.

GFCI Circuit Breaker — A GFCI circuit breaker is provided to

protect against electrical ground fault and protect the generator

against electrical overload.

Grounding Fastener — If required, please consult a qualified

electrician, electrical inspector, or local agency having jurisdiction.

Hour Meter — Displays and records how many hours your

generator has run (up to 9,999.9).

Idle Control Switch — The idle control runs the engine at

normal (high) speeds when there is a load present and runs the

engine at idle (low) speeds when a load is not present.

Ignition Switch — Push to start and stop the engine.

Oil Fill Cap — Add oil to engine here.

Spark Arrester Muffler — Exhaust muffler lowers engine noise

and is equipped with a spark arrester screen.

Choke Lever

120 Volt AC, 20 Amp

Duplex Receptacles

12 Volt DC

Receptacle

Spark Arrester Muffler

Ignition Switch

Grounding

Fastener

Air Cleaner

Fuel Tank

Oil Fill Cap

Data Tag

Hour Meter

Idle Control Switch

GFCI Circuit Breaker

Circuit Breakers (AC)

120/240 Volt AC, 30 Amp

Locking Receptacle

120 Volt AC, 30 Amp

Locking Receptacle

BSPP Generator

ASSEMBLY

Your generator requires some assembly and is ready for

use after it has been properly serviced with the

recommended oil and fuel.

If you have any problems with the assembly of your

generator, please call the generator helpline at

1-800-743-4115.

Remove Generator From Carton

1. Set the carton on a rigid flat surface with "This Side

Up" arrows pointing upward.

2. Carefully open the top flaps of the shipping carton.

3. Cut down corners at one end of carton from top to

bottom and lay that side of carton down flat.

4. Remove all packing material, carton fillers, etc.

5. Remove the generator from the shipping carton.

Carton Contents

Check all contents against those listed below:

• Main unit

• Engine oil

• Owner’s manual

• Engine manual

• Battery charge cables

• Battery charger

• Locking 120/240V, 30A plug

• Locking 120V, 30A plug

• Wheel kit

If any parts are missing or damaged, call the generator

helpline at 1-800-743-4115.

ELECTRIC START

Your unit is equipped with electric start capability but can

be started manually. If you choose not to use the electric

start feature, you do not need to install the negative

battery cable.

Check Battery / Attach Negative

Battery Wire

The sealed battery on the generator is fully charged and

pre–installed except for the negative (black) battery cable.

To install:

1. Cut off tie wrap securing loose end of negative (black)

cable.

2. Remove nut and washer on negative battery terminal.

3. Slide negative battery cable over screw on negative

terminal (Figure 1).

4. Reattach washer and nut and tighten.

5. Verify that connections to battery and generator are

tight and secure.

Figure 1 — Negative Battery Connection

Positive battery cable

Screw

Negative

battery

cable

Washer

Nut

BSPP Generator

BEFORE STARTING THE

ENGINE

Add Engine Oil

• Place generator on a level surface.

• Refer to engine owner’s manual and follow oil

recommendations and instructions.

NOTE: Check oil often during engine break–in. Refer to

engine owner’s manual for recommendations.

NOTE: The generator assembly rotates on a prelubricated

and sealed ball bearing that requires no additional

lubrication for the life of the bearing.

Add Fuel

NOTE: This gasoline engine is certified to operate on

gasoline. Exhaust Emission Control System: EM (Engine

Modifications).

1. Use clean, fresh, regular UNLEADED fuel with a

minimum of 85 octane. DO NOT use fuel which

contains Methanol. DO NOT mix oil with fuel.

2. Clean area around fuel fill cap, remove cap.

3. Slowly add regular unleaded fuel to fuel tank. Be careful

not to fill above the baffle.This allows adequate space

for fuel expansion (Figure 2).

4. Install fuel cap and wipe up any spilled fuel.

CAUTION

• Refer to engine manual for oil fill information.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

Any attempt to crank or start the engine before it has

been properly filled with the recommended oil will result

in equipment failure.

WHEN ADDING FUEL

• Turn generator OFF and let it cool at least 2 minutes before

removing fuel cap. Loosen cap slowly to relieve pressure in

tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank.Allow space for fuel expansion.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WARNING

FUEL

TANK

Figure 2 — Typical Fuel Expansion Space

Baffle

BSPP Generator

USING THE GENERATOR

System Ground

The generator has a system ground that connects the

generator frame components to the ground terminals on

the AC output receptacles.The system ground is connected

to the AC neutral wire (see “Equipment Description”,

earlier in this manual).

Special Requirements

There may be Federal or State Occupational Safety and

Health Administration (OSHA) regulations, local codes, or

ordinances that apply to the intended use of the generator.

Please consult a qualified electrician, electrical inspector, or

the local agency having jurisdiction.

• In some areas, generators are required to be registered

with local utility companies.

• If the generator is used at a construction site, there may

be additional regulations which must be observed.

Connecting to a Building’s Electrical

System

Connections for standby power to a building’s electrical

system must be made by a qualified electrician.The

connection must isolate the generator power from utility

power, and must comply with all applicable laws and

electrical codes.

Generator Location

Generator Clearance

The generator must be at least 5 ft. (152 cm) from

structures having combustible walls and/or other

combustible materials. Leave at least 3 ft. (92 cm) all around

generator including overhead, for adequate cooling,

maintenance and servicing.

Place generator in a well ventilated area, which will allow

for removal of deadly exhaust gas. DO NOT place

generator where exhaust gas could accumulate and enter

inside or be drawn into a potentially occupied building.

Ensure exhaust gas is kept away from any windows, doors,

ventilation intakes or other openings that can allow exhaust

gas to collect in a confined area (Figure 3). Prevailing winds

and air currents should be taken into consideration when

positioning generator.

• When using generator for backup power, notify utility

company. Use approved transfer equipment to isolate

generator from electric utility.

• Use a ground fault circuit interrupter (GFCI) in any damp or

highly conductive area, such as metal decking or steel work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain.

• DO NOT handle generator or electrical cords while standing

in water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator.

Generator produces powerful voltage.

Failure to isolate generator from power utility

can result in death or injury to electric utility

workers due to backfeed of electrical energy.

DANGER

• Operate generator ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes or other openings.

• DO NOT operate generator inside any building or enclosure,

including the generator compartment of a recreational vehicle (RV).

Running generator gives off carbon monoxide,

an odorless, colorless, poison gas.

Breathing carbon monoxide will cause nausea,

fainting or death.

DANGER

Figure 3 — Generator Clearance

Exhaust Port

BSPP Generator

OPERATING THE

GENERATOR

IMPORTANT: Always unplug the battery float charger

before starting the generator.

Starting the Engine

Disconnect all electrical loads from the generator. Use the

following start instruction steps in numerical order:

1. Make sure unit is on a level surface.

IMPORTANT: Failure to start and operate unit on a level

surface will cause the unit not to start or shut down during

operation.

2. Turn fuel valve to “On” position (Figure 4).

3. Make sure Idle Control switch is in “Off” position

(Figure 5).

4. Follow start instructions given in engine owner’s manual.

Push and hold the Ignition switch in “Start” position

(Figure 6) until generator starts.To prolong the life of

starter components, DO NOT hold Ignition switch in

“Start” position for more than 15 seconds, and pause

for 1 minute.

NOTE: If engine starts after 3 pulls but fails to run, or if

unit shuts down during operation, make sure unit is on a

level surface and check for proper oil level in crankcase.

This unit may be equipped with a low oil protection device.

See engine manual.

Connecting Electrical Loads

• Let engine stabilize and warm up for a few minutes after

starting.

• Plug in and turn on the desired 120 and/or 240 Volt AC,

single phase, 60 Hz electrical loads.

• DO NOT connect 240 Volt loads to the 120 Volt duplex

receptacles.

• DO NOT connect 3–phase loads to the generator.

Figure 6 — Ignition Switch

Figure 4 — Fuel Shut-off Valve

• See “Don’t Overload Generator”.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator

before stopping generator.

Exceeding generators wattage/amperage capacity can

damage generator and/or electrical devices connected

to it.

CAUTION

Figure 5 — Idle Control Switch

• DO NOT touch hot surfaces.

• Allow equipment to cool before touching.

• The generator must be at least 5 feet from structures having

combustible walls and/or other combustible materials.

• Keep at least 3 feet of clearance on all sides of generator for

adequate cooling, maintenance and servicing.

• In the State of California a spark arrester is required by law

(Section 4442 of the California Public Resources Code). Other

states may have similar laws. Federal laws apply on federal

lands. If you equip the muffler with a spark arrester, it must be

maintained in effective working order.

Running engines produce heat.Temperature of

muffler and nearby areas can reach or exceed

150°F (65°C).

Severe burns can occur on contact.

Combustible debris, such as leaves, grass, brush,

ect. can catch fire.

WARNING

BSPP Generator

• DO NOT connect 50 Hz loads to the generator.

• DO NOT OVERLOAD THE GENERATOR. See

“Don’t Overload Generator”.

Stopping the Engine

1. Turn OFF and unplug ALL electrical loads from

generator panel receptacles. NEVER start or stop engine

with electrical devices plugged in and turned ON.

2. Move idle control switch to “Off” position.

3. Let engine run at no-load for several minutes to

stabilize internal temperatures of engine and generator.

4. Move fuel valve to “Off” position.

5. Set Ignition switch in “Stop” position.

Operating Automatic Idle Control

This switch is designed to greatly improve fuel economy.

When this switch is turned ON, the engine will only

run at its normal high governed engine speed when

electrical loads are connected.When an electrical load is

removed, the engine will run at a reduced speed.

With the switch off, the engine will run at the normal

high engine speed. Always have the switch off when

starting and stopping the engine.

Charging a Battery

Your generator has the capability of recharging a discharged

12 Volt automotive or utility style storage battery. DO

NOT use the unit to charge any 6 Volt batteries. DO NOT

use the unit to crank an engine having a discharged battery.

To recharge 12 Volt batteries, proceed as follows:

1. Check fluid level in all battery cells. If necessary, add

ONLY distilled water to cover separators in battery

cells. DO NOT use tap water.

2. If battery is equipped with vent caps, make sure they

are installed and are tight.

3. If necessary, clean battery terminals.

4. Connect battery charge cable connector plug to panel

receptacle identified by the words “12-VOLTS D.C.”.

5. Move idle control switch to “Off” position.

6. Connect battery charge cable clamp with red handle

to the positive (+) battery terminal (Figure 7).

7. Connect battery charge cable clamp with black handle

to the negative (–) battery terminal (Figure 7).

8. Start engine. Let engine run while battery recharges.

9. When battery has charged, shut down engine

NOTE: Use an automotive hydrometer to test battery state

of charge and condition. Follow the hydrometer

manufacturer’s instructions carefully. Generally, a battery is

considered to be at 100% state of charge when specific gravity

of its fluid (as measured by hydrometer) is 1.260 or higher.

How to Use the Battery Charger

Use battery float charger jack to keep the starting battery

charged and ready for use. Battery charging should be done

in a dry location, such as inside a garage.

1. Plug charger into unit’s “Battery Float Charger” jack,

which is located on the control panel (Figure 8). Plug

battery charger into a 120 Volt AC wall receptacle.

Figure 7 — Battery Connections

Figure 8 — Battery Charger Jack

• DO NOT allow any open flame, spark, heat, or lit cigarette

during and for several minutes after charging a battery.

• Wear protective goggles, rubber apron, and rubber gloves.

Storage batteries give off explosive hydrogen gas

during recharging.

Hydrogen gas stays near battery for a long time

after battery has been charged.

Slightest spark will ignite hydrogen and cause

explosion.

You can be blinded or severely injured.

Battery electrolyte fluid contains acid and is

extremely caustic.

Contact with battery fluid will cause severe

chemical burns.

DANGER

BSPP Generator

2. Unplug charger from unit and wall outlet when

generator is being started and while in operation.

3. Keep charger plugged in when generator is not in use

to prolong battery life.The charger has a built in float

equalizer and will not overcharge battery, even when

plugged in for an extended period of time.

IMPORTANT: See “Battery Maintenance” on page 16 for

additional information.

COLD WEATHER

OPERATION

Under certain weather conditions (temperatures below

40°F [4°C] and a high dew point), your generator may

experience icing of the carburetor and/or the crankcase

breather system.

Build a structure that will enclose three sides and the top

of the generator:

1. Make sure entire muffler-side of generator is exposed.

Note that your generator may appear different from

that shown in Figure 9.

2. Ensure a minimum of three feet clearance between

open side of box and nearest object.

3. Face exposed end away from wind and elements.

4. Enclosure should hold enough heat created by

generator to prevent problems.

RECEPTACLES

120/240 Volt AC, 30 Amp, Locking

Receptacle

Use a NEMA L14–30 plug with this receptacle. Connect a

4–wire cord set rated for 250 Volts AC at 30 Amps (or

greater) (Figure 10).You can use the same 4–wire cord if

you plan to run a 120 Volt load.

This receptacle powers 120/240 Volt AC, 60 Hz, single

phase loads requiring up to 3,600 watts of power at

30 Amps for 120 Volts; 7,200 watts of power (7.2 kW) at

30 Amps for 240 Volts.The outlet is protected against

overload by a push–to–reset circuit breaker and/or a 2 pole

GFCI circuit breaker.

• NEVER attempt to power a device requiring more

amperage than generator or receptacle can supply.

• DO NOT overload the generator. See “Don’t Overload

Generator”.

Receptacles may be marked with rating value greater

than generator output capacity.

CAUTION

Figure 9 — Permanent Cold Weather Shelter

Wind

• Operate generator ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes or other openings.

• DO NOT operate generator inside any building or enclosure,

including the generator compartment of a recreational vehicle (RV).

Running generator gives off carbon monoxide,

an odorless, colorless, poison gas.

Breathing carbon monoxide will cause nausea,

fainting or death.

DANGER

Figure 10 — 120/240 Volt AC, 30 Amp Receptacle

4-Wire Cord Set

240V

120V

W (Neutral)

X (Hot)

Y (Hot)

NEMA L14-30

Ground (Green)

BSPP Generator

120 Volt AC, 30 Amp Locking

Receptacle

Use a NEMA L5-30 plug with this receptacle. Connect a

3-wire cord set rated for 125 Volts AC at 30 Amps to the

plug (Figure 11).

Use this receptacle to operate 120 Volt AC, 60 Hz, single

phase loads requiring up to 3,600 watts (3.6 kW) of power

at 30 Amps.The outlet is protected against overload by a

push–to–reset circuit breaker and/or a 2 pole GFCI circuit

breaker.

120 Volt AC, 20 Amp, Duplex

Receptacle

Each duplex receptacle (Figure 12) is protected against

overload by a push–to–reset circuit breaker and/or a 2 pole

GFCI circuit breaker.

Use each receptacle to operate 120 Volt AC, single–phase,

60 Hz electrical loads requiring up to 2,400 watts (2.4 kW)

at 20 Amps of current. Use cord sets that are rated for

125 Volt AC loads at 20 Amps (or greater).

12 Volt DC, 10 Amp Receptacle

This receptacle (Figure 13) allows you to recharge a 12 Volt

automotive or utility style storage battery.

This receptacle can not recharge 6 Volt batteries and can

not be used to crank an engine having a discharged battery.

See “Charging a Battery” on page 10 before attempting to

recharge a battery.This outlet is protected by a 10 Amp self

resetting circuit breaker.

Figure 12 — 120 Volt AC, 20 Amp, Duplex Receptacle

Figure 13 — 12 Volt DC, 10 Amp Receptacle

Figure 11 — 120 Volt AC, 30 Amp, Locking Receptacle

3-Wire Cord Set

Neutral

120V

Hot

Ground (Green)

NEMA L5-30

BSPP Generator

Ground Fault Protection

This unit is equipped with a Ground Fault Circuit

Interrupter (GFCI).This device meets applicable federal,

state and local codes.

The GFCI protects against electrical shock that may be

caused if your body becomes a path which electricity

travels to reach ground.This could happen if you touch a

“Live” appliance or wire, or are touching plumbing or other

materials that connect to the ground.

When protected by a GFCI, one may still feel a shock, but

the GFCI should cut current off quickly enough so that a

person in normal health should not suffer any serious

electrical injury.

Test GFCI Circuit Breaker

Test your GFCI circuit breaker (Figure 14) every month, as

follows:

1. While generator is running, push white “Test” button.

The circuit breaker should trip (handle will move to

approximate center position), which will disconnect

power to outlets.

2. If handle moves to center, reset circuit breaker by

firmly moving handle to “Off” (down) position, then to

“On” (up) position.

During Generator Use

If circuit breaker trips during use, it usually indicates faulty

electrical equipment or cords. However, test the circuit

breaker as follows;

1. Disconnect loads, reset and test circuit breaker as

described earlier. Let generator run without any loads

for 1 minute.

2. If circuit breaker tests correctly, the electrical equipment

or extension cords may be faulty. Replace faulty

electrical equipment and cords before further use.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain.

• DO NOT handle generator or electrical cords while standing

in water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator or electrical loads.

Generator produces powerful voltage.

DANGER

• The GFCI will not protect you against the following situations:

-Line-to-line shocks;

-Current overloads or line-to-line short circuits.

• The fuse or circuit breaker at the control panel must provide

such protection.

Generator produces powerful voltage.

DANGER

• DO NOT use generator.

• Call a Briggs & Stratton Power Products service center.

If circuit breaker does not trip:

CAUTION

Figure 14 — GFCI Circuit Breaker

• DO NOT use generator.

• Call a Briggs & Stratton Power Products service center.

If circuit breaker does not reset properly:

CAUTION

• DO NOT use generator.

• Call a Briggs & Stratton Power Products service center.

If circuit breaker trips in the 1 minute period:

CAUTION

• Have qualified personnel check all electrical equipment and

cords for any defects.

• Replace electrical equipment and cords or take to a qualified

repair center.

If circuit breaker tests correctly:

CAUTION

BSPP Generator

DON'T OVERLOAD

GENERATOR

Capacity

You must make sure your generator can supply enough

rated (running) and surge (starting) watts for the items you

will power at the same time. Follow these simple steps:

1. Select the items you will power at the same time.

2. Total the rated (running) watts of these items.This is

the amount of power your generator must produce to

keep your items running. See Figure 15.

3. Estimate how many surge (starting) watts you will

need. Surge wattage is the short burst of power

needed to start electric motor-driven tools or

appliances such as a circular saw or refrigerator.

Because not all motors start at the same time, total

surge watts can be estimated by adding only the

item(s) with the highest additional surge watts to the

total rated watts from step 2.

Example:

Total Rated (Running) Watts = 3075

Highest Additional Surge Watts = 1800

Total Generator Output Required = 4875

Power Management

To prolong the life of your generator and attached devices,

it is important to take care when adding electrical loads to

your generator.There should be nothing connected to the

generator outlets before starting it's engine.The correct

and safe way to manage generator power is to sequentially

add loads as follows:

1. With nothing connected to the generator, start the

engine as described in this manual.

2. Plug in and turn on the first load, preferably the largest

load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly).

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

NEVER add more loads than the generator capacity.Take

special care to consider surge loads in generator capacity,

as described above.

*Wattages listed are approximate only. Check tool or

appliance for actual wattage.

Tool or Appliance

Rated (Running)

Watts

Additional Surge

(Starting) Watts

Window Air

Conditioner

1200 1800

Refrigerator 800 1600

Deep Freezer 500 500

Television 500 -

Light (75 Watts) 75 -

3075 Total

Running Watts

1800 Highest

Surge Watts

Tool or Appliance

Rated*

(Running)

Watts

Additional

Surge

(Starting)

Watts

Essentials

Light Bulb - 75 watt 75 -

Deep Freezer 500 500

Sump Pump 800 1200

Refrigerator/Freezer - 18 Cu. Ft. 800 1600

Water Well Pump - 1/3 HP 1000 2000

Heating/Cooling

Window AC - 10,000 BTU 1200 1800

Window Fan 300 600

Furnace Fan Blower - 1/2 HP 800 1300

Kitchen

Microwave Oven - 1000 Watt 1000 -

Coffee Maker 1500 -

Electric Stove - Single Element 1500 -

Hot Plate 2500 -

Family Room

DVD/CD Player 100 -

VCR 100 -

Stereo Receiver 450 -

Color Television - 27” 500 -

Personal Computer w/17” monitor 800 -

Other

Security System 180 -

AM/FM Clock Radio 300 -

Garage Door Opener - 1/2 HP 480 520

Electric Water Heater - 40 Gallon 4000 -

DIY/Job Site

Quartz Halogen Work Light 1000 -

Airless Sprayer - 1/3 HP 600 1200

Reciprocating Saw 960 960

Electric Drill - 1/2 HP 1000 1000

Circular Saw - 7 1/4” 1500 1500

Miter Saw - 10” 1800 1800

Table Planer - 6” 1800 1800

Table Saw/Radial Arm Saw - 10” 2000 2000

Air Compressor - 1-1/2 HP 2500 2500

Figure 15 - Wattage Reference Chart

BSPP Generator

SPECIFICATIONS

Maximum Surge Watts . . . . . . . . . . . . . . . 10,000 Watts

Continuous Wattage Capacity . . . . . . . . . . 8,000 Watts

Power Factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0

Rated Maximum Continuous Load Current

At 120 Volts . . . . . . . . . . . . . . . . . . . . . . . 66.6 Amps

At 240 Volts . . . . . . . . . . . . . . . . . . . . . . . 33.3 Amps

Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-phase

Rated Frequency . . . . . . . . . . . . . . . . . . . . . . . 60 Hertz

Fuel Tank Capacity . . . . . . . . . . . . . . . . . . . 7 U.S. gallons

Shipping Weight . . . . . . . . . . . . . . . . . . . . . . . . . . 270 lbs.

GENERAL MAINTENANCE

RECOMMENDATIONS

The Owner/Operator is responsible for making sure that

all periodic maintenance tasks are completed on a timely

basis; that all discrepancies are corrected; and that the unit

is kept clean and properly stored. NEVER operate a

damaged or defective generator.

Engine Maintenance

See engine owner’s manual for instructions.

KEEP OUT OF REACH OF CHILDREN. DON'T

POLLUTE. CONSERVE RESOURCES. RETURN

USED OIL TO COLLECTION CENTERS.

Generator Maintenance

Generator maintenance consists of keeping the unit clean

and dry. Operate and store the unit in a clean dry

environment where it will not be exposed to excessive

dust, dirt, moisture or any corrosive vapors. Cooling air

slots in the generator must not become clogged with snow,

leaves or any other foreign material.

NOTE: DO NOT use a garden hose to clean generator.

Water can enter engine fuel system and cause problems. In

addition, if water enters generator through cooling air slots,

some of the water will be retained in voids and cracks of

the rotor and stator winding insulation.Water and dirt

buildup on the generator internal windings will eventually

decrease the insulation resistance of these windings.

Fuel Valve Maintenance

The fuel valve is equipped with a fuel sediment cup, screen,

retaining ring and o-ring that need to be cleaned every

6 months or 100 hours (whichever occurs first).

1. Move fuel valve to “Off” position.

2. Remove sediment cup from fuel valve. Remove o-ring,

retaining ring and screen from fuel valve (Figure 16).

3. Wash sediment cup, o-ring, retaining ring, and screen in

a nonflammable solvent. Dry them thoroughly.

• Used motor oil has been shown to cause skin cancer in

certain laboratory animals.

• Thoroughly wash exposed areas with soap and water.

Avoid prolonged or repeated skin contact with used

motor oil.

CAUTION

Figure 16 — Fuel Valve Maintenance

Sediment Cup

O-ring

Retaining Ring

Screen

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

GENERATOR

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Unintentional sparking can result in fire or

electric shock.

WARNING

BSPP Generator

4. Place screen, retaining ring, and o-ring into fuel valve.

Install sediment cup and tighten securely.

5. Move fuel valve to “On” position, and check for leaks.

Replace o-ring if there is any leakage.

Battery Maintenance

Other than float charging, described elsewhere, no

maintenance is required for the starting battery. Keep the

battery and terminals clean and dry.

IMPORTANT: Battery charging should be performed in a

dry location, such as inside a garage.

Generator Cleaning

• Use a damp cloth to wipe exterior surfaces clean.

• Use a soft bristle brush to loosen caked on dirt or oil.

• Use a vacuum cleaner to pick up loose dirt and debris.

• Use low pressure air (not to exceed 25 psi) to blow

away dirt. Inspect cooling air slots and opening on

generator.These openings must be kept clean and

unobstructed.

STORAGE

The generator should be started at least once every seven

days and allowed to run at least 30 minutes. If this cannot

be done and you must store the unit for more than

30 days, use the following guidelines to prepare it for

storage.

Generator Storage

• Clean the generator as outlined in “Generator Cleaning”.

• Check that cooling air slots and openings on generator

are open and unobstructed.

Engine Storage

See engine owner’s manual for instructions.

Other Storage Tips

• To prevent gum from forming in fuel system or on

essential carburetor parts, add fuel stabilizer into fuel

tank and fill with fresh fuel. Run the unit for several

minutes to circulate the additive through the carburetor.

The unit and fuel can then be stored for up to

24 months. Fuel stabilizer can be purchased locally.

• DO NOT store fuel from one season to another unless

it has been treated as described above.

• Replace fuel container if it starts to rust. Rust and/or dirt

in fuel can cause problems if it's used with this unit.

• Store unit in a clean and dry area.

• DO NOT place a storage cover over a hot generator.

• Let equipment cool for a sufficient time before placing the

cover on the equipment.

Storage covers can be flammable.

WARNING

• DO NOT expose generator to excessive moisture, dust, dirt,

or corrosive vapors.

• DO NOT insert any objects through cooling slots.

Improper treatment of generator can damage it and

shorten its life.

CAUTION

BSPP Generator

TROUBLESHOOTING

Problem Cause Correction

No AC output is available, but

generator is running.

1. One of the circuit breakers is open.

2. Fault in generator.

3. Poor connection or defective cord

set.

4. Connected device is bad.

1. Reset circuit breaker.

2. Contact Authorized service facility.

3. Check and repair.

4. Connect another device that is in

good condition.

Generator runs good at no-load

but "bogs" down" when loads are

connected.

1. Short circuit in a connected load.

2. Generator is overloaded.

3. Shorted generator circuit.

1. Disconnect shorted electrical load.

2. See "Don't Overload Generator".

3. Contact Authorized service facility.

Generator will not start; or starts

and runs rough.

1. Failed battery.

2. Low oil level.

1. Replace battery.

2. Fill crankcase to proper level or

place generator on level surface.

Generator shuts down during

operation.

1. Out of gasoline.

2. Low oil level.

1. Fill fuel tank.

2. Fill crankcase to proper level or

place generator on level surface.

Generator lacks power. Load is too high. See "Don't Overload Generator".

BSPP Generator

NOTES

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC EQUIPMENT OWNER WARRANTY POLICY

LIMITED WARRANTY

Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s), of the equipment that is defective in material

or workmanship or both. Transportation charges on parts submitted for repair or replacement under this warranty must be borne by

purchaser. This warranty is effective for the time periods and subject to the conditions stated below. For warranty service, find the nearest

Authorized Service Dealer in our dealer locator map at www.briggspowerproducts.com.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW ANY

AND ALL IMPLIED WARRANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED

TO THE EXTENT EXCLUSION IS PERMITTED BY LAW. Some states or countries do not allow limitations on how long an implied warranty

lasts, and some states or countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation

and exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state

to state or country to country.

OUR EQUIPMENT*

OUTBOARD

MOTOR

PRESSURE

WASHER

WATER PUMP

(Not available in the

USA)

PORTABLE

GENERATOR

WELDER

Less tthan 110 KKW 10 KKW oor ggreater

Transfer sswitch

2 years

none

1 year

90 days

1 year

90 days

2 years

1 year

2 years

none

3 years or

1500 hours

none

3 years

none

WARRANTY PERIOD**

HOME GENERATOR SYSTEM

Consumer Use

Commercial Use

* The engine and starting batteries are warranted solely by the manufacturers of those products.

** 2 years for all consumer products in the European Union. Parts only on 2nd year for consumer use of Portable Generator and

Home Generator System - Less than 10 KW, outside of European Union.

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time

stated in the table above. “Consumer use" means personal residential household use by a retail consumer. “Commercial use" means all other

uses, including use for commercial, income producing or rental purposes. Once equipment has experienced commercial use, it shall thereafter

be considered as commercial use for purposes of this warranty. Equipment used for Prime Power in place of utility are not applicable to

this warranty. Electric Powered Pressure Washers used for commercial purposes are not warranted.

NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR

PROOF OF PURCHASE RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY

SERVICE IS REQUESTED, THE MANUFACTURING DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY

PERIOD.

ABOUT YOUR WARRANTY

We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most

warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For example, warranty service would not

apply if equipment damage occurred because of misuse, lack of routine maintenance, shipping, handling, warehousing or improper installation.

Similarly, the warranty is void if the manufacturing date or the serial number on the equipment has been removed or the equipment has been altered

or modified. During the warranty period, the Authorized Service Dealer, at its option, will repair or replace any part that, upon examination, is found to

be defective under normal use and service. This warranty will not cover the following repairs and equipment:

• Normal Wear: Outdoor Power Equipment, like all mechanical devices, needs periodic parts and service to perform well. This warranty does not

cover repair when normal use has exhausted the life of a part or the equipment.

• Installation and Maintenance: This warranty does not apply to equipment or parts that have been subjected to improper or unauthorized

installation or alteration and modification, misuse, negligence, accident, overloading, overspeeding, improper maintenance, repair or storage so as,

in our judgment, to adversely affect its performance and reliability. This warranty also does not cover normal maintenance such as adjustments,

fuel system cleaning and obstruction (due to chemical, dirt, carbon, lime, etc.).

• Other Exclusions: This warranty excludes wear items such as quick couplers, oil gauges, belts, o-rings, filters, pump packing, etc., pumps that

have been run without water supplied or damage or malfunctions resulting from accidents, abuse, modifications, alterations, or improper servicing

or freezing or chemical deterioration. Accessory parts such as guns, hoses, wands and nozzles are excluded from the product warranty. Also

excluded is used, reconditioned, and demonstration equipment; equipment used for prime power in place of utility power and equipment used in

life support applications.

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON, WI, USA

Effective June 1, 2004 replaces all undated Warranties and all Warranties dated before June 1, 2004

BSPP Génératrice

TABLE DES MATIÈRES

Règles de Sécurité. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-22

Connaissez Votre Générateur . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Assemblage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25

Opération . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-32

Entretien . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33-34

Rangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Dépannage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Remarques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

DESCRIPTION DE L ÉQUIPEMENT

Lisez avec soin ce manuel et familiarisez-vous avec

votre générateur. Connaissez ses applications, ses

limitations et les dangers qu'il implique.

Ce générateur est un générateur entraîné par un moteur à champ

magnétique rotatif produisant du courant alternatif (c.a.). Il a été

conçu pour fournir du courant électrique pour faire marcher des

charges compatibles d'éclairage, d'appareils ménagers, d'outil et de

moteur. Le champ tournant du générateur est entraîné à

3,600 T/M par un moteur.

Cette génératrice comprend une protection de prise de type

GFCI (disjoncteur de fuite de terre) et ses neutres sont raccordés

à la terre afin de répondre aux normes de l'OSHA sur les

chantiers de construction. Cette génératrice ne fonctionnera pas

si elle est branchée à un commutateur de transfert puisque le

neutre de la boîte de disjoncteurs principale de la résidence ou de

l'édifice est lui aussi raccordé à la terre. Lorsque la génératrice et

la boîte de disjoncteurs de la résidence ou de l'édifice ont tous

deux le neutre raccordé à la terre, le disjoncteur GFCI de la

génératrice s'ouvre et coupe le courant vers les prises.

ATTENTION! NE PAS dépasser la capacité en watts ou en

Ampères du générateur.Voir "Ne Pas Surcharger Générateur"

pour l'information spécifique.

Tout a été mis en oeuvre pour que les informations contenues

dans ce manuel soient exactes et à jour. Cependant, nous se

réserve le droit de changer, d'altérer ou d'améliorer le produit à

n'importe quel moment sans avis préalable.

Le Système de contrôle de l'émission du générateur est garanti

pour des normes établies par L'Agence de protection de

l'environnement. Pour des informations sur la garantie, se reporter

au manuel du moteur.

RÈGLES DE SÉCURITÉ

Ceci est la sûreté le symbole vif. Il est utilisé pour

vous alerter aux dangers de blessure personnels

potentiels. Obéir tous messages de sûreté qui suivent

ce symbole éviter la blessure ou la mort possibles.

Le symbole indiquant un message de sécurité est accompagné d'un

mot indicateur (DANGER,ATTENTION,AVERTISSEMENT), d'un

message illustré et/ou d'un message de sécurité visant à vous

avertir des dangers. DANGER indique un danger qui, s'il n'est pas

évité, provoquera des blessures graves, voire fatales.

AVERTISSEMENT indique un danger qui, s'il n'est pas évité, peut

provoquer des blessures graves, voire fatales. ATTENTION

indique un danger qui, s'il n'est pas évité, peut provoquer des

blessures mineures ou légères. Le mot ATTENTION, lorsqu'il est

utilisé sans le symbole d'alerte, indique une situation pouvant

endommager l'équipement. Suivez les messages de sécurité pour

éviter ou réduire les risques de blessures ou de mort.

Symboles de Danger et Moyens

L’échappement du moteur de ce produit contient des produits

chimiques que l’État de Californie considère comme causant le

cancer, des déformations à la naissance ou d’autres dangers

concernant la reproduction.

AVERTISSEMENT

Feu

Explosion

Emanations Toxiques

Surface Chaude

Choc Électrique

Électrocution

Choc Électrique

Pression Explosive

Brûlures Chimiques

• L'enlèvement du raccordement du neutre pourrait entraîner la

mort, des blessures corporelles ou des dommages matériels.

N'ENLEVEZ PAS le raccordement du neutre.

AVERTISSEMENT

La page charge ...

Briggs & Stratton 1934 Manuel utilisateur

Marque: Briggs & Stratton

Modèle: 1934

Catégorie: Accessoires pour véhicules automobiles

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Briggs & Stratton 1934 User manual
español: Briggs & Stratton 1934 Manual de usuario

Briggs & Stratton 1934 Manuel utilisateur

Ce manuel convient également à

Briggs & Stratton 1934 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents