Candy CTS6CEXWIFI Manuel utilisateur

FRANÇAIS NOTICE D'INSTALLATION ET DUTILISATION

DEUTSCH INSTALLATIONS- UND BEDIENUNGSANLEITUNG

ESPAÑOL MANUAL DE USO E INSTALACIÓN

ENGLISH INSTALLATIONANDUSER’S MANUAL

30

INSTALLATION AND USER’S MANUAL

CONTENT

INTRODUCTION

2

SAFETY PRECAUTION

2

SPECIFICATION

5

INSTALLATION (VENT OUTSIDE)

6

INSTALLATION (VENT INSIDE)

11

DESCRIPTION OF COMPONENTS

15

OPERATION

15

MAINTENANCE

17

TROBULESHOOTING

18

CONFORMITY WITH DIRECTIVES

19

ENVIRONMENTAL PROTECTION

19

1

INTRODUCTION

Never let the children operate the machine.

The cooker hood is for home use only, not suitable for barbecue, roast

shop and other commercial purpose.

The cooker hood and its filter should be clean regularly in order to keep

in good working condition.

Clean the cooker hood according to the instruction manual and keep the

unit from danger of burning.

Forbid the direct baking from the gas cooker.

Please keep the kitchen room a good convection.

Before connecting this appliance check that the power supply cord is not

damaged. A damage supply cord must be replaced by qualified service

personnel only.

There shall be adequate ventilation of the room when the range hood is

used at the same time as appliances burning gas or other fuels;

The air must not be discharged into a flue that is used for exhausting

fumes from appliances burning gas or other fuels;

Regulations concerning the discharge of air have to be fulfilled.

Thank you for choosing this cooker hood.

This instruction manual is designed to provide you with all required

instructions related to the installation, use and maintenance of the appliance.

In order to operate the unit correctly and safety, please read this instruction

manual carefully before installation and usage.

The cooker hood uses high quality materials, and is made with a streamlined

design. Equipped with large power electric motor and centrifugal fan, it also

provides strong suction power, low noise operation, non-stick grease filter and

easy assembly installation.

Hereby, Candy Hoover Group Srl declares that the radio equipment is in

compliance with Directive 2014/53/EU and with the relevant Statutory

Requirements (for the UKCA market).

The full text of the declaration of conformity is available at the following

internet address: www.candy-group.com.

SAFETY PRECAUTION

2

This appliance if not intended for use by persons(including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person slide for their

safety.

Children should be supervised to ensure that they do not play with the

appliance.

Do not flambé under the range hood.

CAUTION: Accessible parts may become hot when used with cooking

appliance

Electrical Shock Hazard

Only plug this unit into a properly earthed outlet. If in doubt seek

advice from a suitably qualified engineer.

Failure to follow these instructions can result in death, fire, or

electrical shock.

3

32

Direct Connection

The appliance must be connected directly to the mains using an

omnipolar circuit breaker with a minimum opening of 3mm between

the contacts.

The installer must ensure that the correct electrical connection has

been made and that it complies with the wiring diagram.

The cable must not be bent or compressed.

Regularly check the power plug and power cord for damage. If the

supply cord is damaged, it must be replaced by a special cord or

assembly available from the manufacturer or its service agent.

WARNING: This is a Class I appliance and MUST be earthed

This appliance is supplied with a 3 core mains cable coloured as

follows:

Brown = L or Live

Blue = N or Neutral

Green and Yellow = E or Earth

The fuse must be rated at 3 Amps.

Electrical Installation

All installation must be carried out by a competent person or qualified

electrician. Before connecting the mains supply ensure that the mains

voltage corresponds to the voltage on the rating plate.

4

33

Standard Installation Accessories List

Spec.

Illustration Picture

Qty

Casing

1

Upper Chimney

1

Lower Chimney

1

Lower chimney bracket

1

Upper chimney bracket

1

Hanging Board

1

φ8 rawl plugs

φ8×φ6 white color

9

Screws

ST4.0×30

9

φ7.2screws

ST4.0×8

2

5

34

INSTALLATION

（

wall mounting

）

If you have an outlet to the outside, your cooker hood can be connected as

below picture by means of an extraction duct (enamel, aluminum, flexible pipe or

inflammable material with an interior diameter of 150mm)

1. Before installation, turn the unit off and unplug it from the outlet.

2. The cooker hood should be placed at a distance of 65~75cm above

the cooking plane for best effect.

3. Drill 3 x 8mm holes to accommodate the bracket. Screw and tighten

the bracket onto the wall with the screws provided.

Wall plug

Wall bracket

107.5mm

Screw(4mm x 30mm)

6

eed to drill 2x8mm extra holes & fixing screws & screw plugs before

installation. Voor schuine modellen

For inclined panel Model

7

35

4. Leave up the cooker hood and hang onto the wall bracket hook.

Cooker hook

Wall

bracket

5. Fix the one-way-valve to the air outlet of the cooker hood. Then,

attached the exhaust pipe onto the one-way-valve as shown below.

Exhaust pipe

Cooker hood

8

36

6.

i. Place the glass in appropriate position on the top the cooker

hood.

ii. Fix with 4 screws and washer. In order to avoid the glass

cracking, please do not tighten the screws too strongly.

i. By Put the inner chimney into outer chimney .Then pulling out

the inner chimney upwards. Adjust to reach the height required.

ii. Sliding the chimney to adjust the chimney height. When the

height you required is reached, then hang the fixing hole to the fixing

screws as showed in below pictures.

Inner chimney

Outer chimney

9

37

8.

i. Drill 2 x 8mm holes to accommodate the plate II. Screw and

tighten the plate II onto the wall with 2 screws provided.

ii. Assembly the chimney onto the unit and fix it with 2 screws.

Plate II

Wall plug

Screw

4mm x 8mm

Screw

(4mm x 30mm)

10

Standard Installation Accessories List

Spec. Illustration Picture Qty

Air Deflector 1

Bracket 1

φ8 rawl plugs

φ8×φ6whitecolor

2

Screws

ST4.0×30

2

Screws

ST3.5×12

2

11

INSTALLATION(AIR DEFLECTOR FOR T-SHAPE,CURVED GLASS,FLAT

GLASS MODELS):

Air deflector is mentioned as included and not optional.

1.Before installation,curve both ends of the bracket as shown below:

2.Fix the bracket to the T-shaped plastic outlet with 2pcs ST3.5x12mm screws

provided.

3.Drill 2 holes to accommodate the wall plugs,then screw and tighten the

bracket onto the wall with 2pcs ST4x30mm screws provided.

12

4.Attach the exhaust pipe onto the air outlet of the cooker hood as shown

below:

5.Install the chimney to the unit and fix it.

o “Please kindly be noted: T-shaped plastic outlet and v-flaps can not be use

datthesametime.Youcanusethemintwoways:1)Addv-flaponexistingo

utlet; 2) Use T-shaped plastic outlet, no add v-flap.”

o “Note: The product is provided with v-flap accessory. This accessory is not

mandatory for installation, operation and use of the product.”

13

38

INSTALLATION (VENT INSIDE)

If you do not have an outlet to the outside, exhaust pipe is not required and

the installation is similar to the one show in section “INSTALLATION (VENT

OUTSIDE)”.

Activated carbon filter can be used to trap odors.

In order to install the activated carbon filter, the grease filter should be

detached first. Press the lock and pull it downward.

Plug the activated carbon filter into the unit and turn it in clockwise direction.

Repeat the same on the other side.

NOTE:

oMake sure the filter is securely locked. Otherwise, it would loosen and

cause dangerous.

oWhen activated carbon filter attached, the suction power will be

lowere

14

Wi-Fi Connection

Long press WiFi icon and enter into connecting mode: the backlit

of WiFi icon keep flashing indicate the connection is under

connecting, the backlit of WiFi icon is light on indicate it is

connected, same for standby mode; long press WiFi icon again

and the connection will be stopped;

Speed plus button

For increasing the speed of the fan

Speed decrease button

For decreasing the speed of the fan.

Light button

Digital display

Fan speed display:"1" for Low speed, "2" for Medium speed,

"3" for High speed, “4” for Booster function.

Quick timer: Press & hold for 1 second, Digital display will

flashing & into 5 minutes count down, after 5 minutes motor & light

will turn off automatic & Buzzer sound for 1 second.

Booster function

This hood has a booster function. To activate the booster, Press

to speed 4, enter into highest speed while the hood is in use

and it will increase speed for 5 minutes, before slowing down

again.

DESCRIPTION OF COMPONENTS

OPERATION

15

Download hOn App

First of all, you should download hOn APP and install to your portable device. Then

enroll your hood.

NOTE

ENROLLMENT CANDY HOOD

1- Press the WiFi button until the icon starts blinking When the pairing is

completed the WiFi icon will be on.

The image of the hood has the only purpose of presenting it. May not be perfectly representative.

16

41

MAINTENANCE

Before cleaning switch the unit off and pull out the plug.

I. Regular Cleaning

Use a soft cloth moistened with hand-warm mildly soapy water or

household cleaning detergent. Never use metal pads, chemical, abrasive

material or stiff brush to clean the unit.

II. Monthly Cleaning for Grease Filter

ESSENTIAL: Clean the filter every month can prevent any risk of fire.

The filter collects grease, smoke and dust…... so the filter is directly

affecting the efficiency of the cooker hood. If not cleaned, the grease

residue (potential flammable) will saturate on the filter. Clean it with

household cleaning detergent.

III. Annual Cleaning for Activated Carbon Filter

Apply SOLELY to unit that installed as a recirculation unit (not vented to

the outside). This filter traps odors and must be replaced at least once a

year

depending on how frequent the cooker hood used.

IV. Changing a light bulb

Remove the screws on the glass, take off the hood glass. Find the

bulb that requires replacement, you will find it located in the light

fixture which is inside the exposed section of the canopy.

Disconnect the light wiring point and remove the bulb holders and

wiring from the hood. Important: It’s not possible to replace the bulbs

individually, it will be necessary to obtain the bulbs, bulb holders and

wiring as a complete part. (LED light: MAX 1.5W)

Fit the replacement bulbs, bulb holders and wiring in the same

manners as the originals. Then reconnect the light wiring point.

17

Refit the hood glass and fasten the glass screws. Make sure the screws are

fully tightened.

TROBULESHOOTING

Fault Cause Solution

Light on, but

fan does not

work

The fan blade is

jammed. Switch off the unit and repair by

qualified service personnel only.

The motor is damaged.

Both light and

fan do not

work

Halogen light bulb burn. Replace the bulb with correct

rating.

Power cord looses. Plug in to the power supply again.

Serious

Vibration of

the unit

The fan blade is

damaged. Switch of the unit and repair by

qualified service personnel only.

The fan motor is not

fixed tightly. Switch off the unit and repair by

qualified service personnel only.

The unit is not hung

properly on the bracket.

Take down the unit and check

whether the bracket is in proper

location.

Suction

performance

not good

Too long distance

between the unit and

the cooking plane Readjust the distance to 65-75cm

Technology Wi-Fi

Standard 802.11 b/g/n

Frequency Band(s)[MHz] 2400 MHz - 2483.5 MHz

Maximum Power[mW] 100 mW

Product information for networked equipment

power consumption of the product in

networked standby if all wired

network ports are connected and all

wireless network ports are activated:

2W

If the Hood has been enrolled with the APP,

turn on the Hood to activate wireless

network port.

How to activate wireless network port:

If the Hood has been enrolled with the APP, turn

off the Hood to deactivate wireless network port.

If the Hood hasn’t been enrolled with the APP,

wireless network port will be deactivated even the

Hood is on.

How to deactivate wireless network port:

18

43

ENVIRONMENTAL PROTECTION

Waste electrical products should not be disposed of with

household waste. Please recycle where facilities exist.

Check with your Local Authority or retailer for recycling

advice.

This appliance is marked according to the European directive 2012/19/EU

on Waste Electrical and Electronic Equipment (WEEE).

By ensuring this product is disposed of correctly, you will help prevent

potential negative consequences for the environment and human health,

which could otherwise be caused by inappropriate waste handling of this

product.

The symbol on the product indicates that this product may not be treated as

household waste. Instead it shall be handed over to the applicable

collection point for the recycling of electrical and electronic equipment

Disposal must be carried out in accordance with local environmental

regulations for waste disposal.

For more detailed information about treatment, recovery and recycling of

this product, please contact your local city office, your household waste

disposal service or the shop where you purchased the product.

CUSTOMER ASSISTANCE SERVICE

If you cannot identify the cause of the operating anomaly, switch off the

appliance and contact the Assistance Service.

PRODUCT SERIAL NUMBER. Where can I find it?

It is important you to inform the Assistance Service of your product code

and its serial number (a 16 character code which begins with the number 3);

this can be found on the guarantee certificate or on the data plate located

on the appliance.

It will help to avoid wasted journeys to technicians, thereby (and most

significantly) saving the corresponding callout charges.

19

La page charge ...

Candy CTS6CEXWIFI Manuel utilisateur

Candy CTS6CEXWIFI Manuel utilisateur

dans d''autres langues

Autres documents