JAYS s-Living Flex Manuel utilisateur

s-Living Flex

Getting started, safety and warranty

Thank You!

Welcome to the new world of JAYS!

Designed and developed with elegance and simplicity as key factors by our Scandinavian team.

Our s-Living Flex is a wireless speaker using the latest Wi-Fi streaming technology, so that music can

be enjoyed in many different settings.

We are excited to present our new speaker and hope you will enjoy the divine sound performance.

Enjoy,

Henrik Andersson

CEO, JAYS

4

Touch panel control – see next page for image reference

1. Long press on/off button to turn on/off your s-Living Flex.

2. Single tap on the PAUSE/PLAY button on the left to PAUSE/PLAY. Long press to switch between Wi-Fi, Bluetooth and AUX.

3. Press + or - to adjust the volume.

4. When in Wi-Fi mode, long press 3 to 6 seconds to enter WAC mode. When in Bluetooth mode, long press 3 to 6 seconds to enter Bluetooth

pairing. Long press 6+ seconds to reset your speaker.

USING YOUR SPEAKER

(EN) English

5

USING YOUR SPEAKER

1

2

3

4

6

How to start

1. Connect power to your speaker. Use included power adapter for s-Living Flex and connect to a power outlet.

2. Press power button for 3 seconds to power ON the speaker and it will boot up, which takes up to a minute. If you need to power OFF, then

press 3 seconds again.

3. Once you hear a voice message from the speaker, you are ready to continue.

The speaker modes

When the speaker is powered ON and ready, you can switch between different modes. Long press PLAY/PAUSE button to switch mode.

You can choose:

• Wi-Fi mode System LED will show PURPLE color (this is default mode)

• Bluetooth mode System LED will show BLUE color

• AUX-In mode System LED will show GREEN color

FIRE UP YOUR

s-Living Flex

7

Using your speaker with battery

You may use your speaker for about 6 hours in playback mode. After that you will need to connect it to the included power outlet. The speaker

will automatically enter standby mode if no music is played for 10 mins. If in standby mode for 60 minutes the s-Living Flex will switch off in order

to not drain your battery. If using your speaker in AUX mode, the speaker will not enter standby mode automatically. When battery is low, LED

will turn yellow. As you re-charge the battery, the LED will breath yellow. When it is fully charged again, the LED will go back to its mode color.

Note

Wi-Fi mode operation require the speaker to be connected to a Wi-Fi network. And this is also needed if you want to use Wi-Fi features such as

Google Cast, AirPlay or Spotify Connect. Furthermore, the speaker is compatible with voice assistants from Google and Apple (Google Assistant

and Siri) if the speaker is also “paired” with Google Home and/or Apple Home (Apple HomeKit). The speaker DO NOT have the voice assistant

function built-in directly.

Important note

If LED’s shortly after power ON is ashing RED, or if you suddenly notice LED’s ashing RED, then DO NOT remove the power plug. This means

that the speaker is installing automatic software updates.

FIRE UP YOUR

s-Living Flex

8

Power on

During start up (power ON the speaker) the power LED will ash fast.

Note: When you power ON the speaker it will always start up in Wi-Fi mode.

Search state

When the speaker is powered ON it will start by being in “search state” trying to search for and connect to the last Wi-Fi network. During this

state the LED will ash. The same will happen (ash) if the speaker is put into “Bluetooth mode”, where you are now able to establish connection

with a previously paired Bluetooth device.

Setup mode or pairing mode

In “Wi-Fi mode” the speaker will automatically enter the “setup mode” within 20 seconds, if the speaker during “search state” does not

successfully re-connect to the previous Wi-Fi network.

In “setup mode” the LED will ash continuously. Same LED behavior will occur if the speaker is set into “Bluetooth pairing mode”.

Playback state

During playback the LED will be ON (solid) and the color of the system LED (Purple, Blue, Green) will indicate what “mode” the speaker is in

(Wi-Fi playback, Bluetooth playback, AUX playback).

Idle mode / network standby mode (sleep mode)

LED will be breathing slowly indicating “no action” or “I am sleeping”.

“Idle mode” will happen as soon as music is paused (no action).

“Standby mode” will happen if there is no action for 20 mins when plugged in and 10 mins when not plugged in. If in standby mode for 60 mins

the s-Living Flex will switch off. To switch on long press ON for three seconds.

LED INDICATIONS AND START UP

9

LED INDICATIONS AND START UP

Power LED /

System LED

Pairing button

Playback mode

(when long press)

Power button

10

Setting up your speaker

“Wi-Fi setup mode” or “Bluetooth pairing mode” is needed for either connecting the speaker to a Wi-Fi network or connecting a new Bluetooth

device to the speaker.

• For “Wi-Fi setup”, the speaker will automatically enter “setup mode” if the previous connection cannot be established. But even though

the speaker is already connected to a Wi-Fi network you can manually force this “mode” by pressing the “pairing button” (Wi-Fi symbol)

for 3 seconds. Note: The speaker must be in “Wi-Fi mode” rst. Forcing this setup mode will only enable Apple setup mode (WAC).

• For “Bluetooth pairing mode” (if you need to pair a new Bluetooth device with your speaker), you need to press the “pairing button”

(Wi-Fi symbol) for 3 seconds. Note: The speaker must be in “Bluetooth mode” rst.

Reset speaker / disable wireless connections: The speaker can be reset to factory defaults by pressing and holding “pairing button” (Wi-Fi

symbol) for 6 seconds. This will clear all speaker settings and afterwards it will be ready for Wi-Fi setup again. A reset will also disable all wireless

connections.

SETUP MODE

Purple LED – ”Wi-Fi mode” Blue LED – ”Bluetooth mode”

11

If you hear this message, the speaker is either in “Wi-Fi setup mode” waiting for Wi-Fi connection to

be set up or the speaker is in “Bluetooth mode” waiting for previous paired devices to connect.

If you hear this message, the speaker is successfully connected to a Wi-Fi network or you have

successfully re-connected a previous paired Bluetooth device. You are now ready to play music.

WAITING FOR CONNECTION

CONNECTION SUCCESSFUL,

TIME TO PLAY

Voice messages from your speaker

VOICE MESSAGES

12

Wi-Fi setup

There are two methods of connecting your speaker to a Wi-Fi network, while the speaker is in “Wi-Fi setup mode”. In either case you need to

follow the Google or Apple setup methods, and you must be within close range of your speaker while doing so.

Note: The speaker will reply “Connection Successful , Time To Play” once connection is ready.

Using the Google Home App

You need to download and install the Google Home App on any of your compatible devices (e.g. smart phone or tablet). Your device must be

connected to the same Wi-Fi network of which you want the speaker(s) to be connected. Open the Google Home App and follow the on-screen

guidelines for setting up a new device (in this case, connecting your speaker).

Note: For more information about using Google Home App and setting up your speaker to Google Home, and to Wi-Fi networks through the

Google Home App, please refer to Google’s website.

Using Apple setup methods

1. (WAC setup) Open Wi-Fi settings on your iOS device. On the “Choose a network...” list, you will nd your speaker listed with the headline

“Setup new AirPlay speaker”. Follow these steps and your speaker will connect to the Wi-Fi network.

2. Download and install the Apple Home App to setup the speaker to your Wi-Fi and the Apple HomeKit universe. Please refer to Apple’s

website for using the Apple Home App.

Bluetooth pairing

Set your speaker into “Bluetooth pairing mode” and open the Bluetooth settings screen on your device. The speaker will appear on the list,

simply choose it to pair it to your device. The speaker’s “pairing mode” is only active for 2 minutes.

Note: The speaker will reply “connection successful, time to play” when your device is successfully paired to the speaker.

CONNECT TO WI-FI OR BLUETOOTH PAIRING

13

Wi-Fi playback

With the speaker connected to a Wi-Fi network you can use any of the following streaming technologies for playback:

Apple AirPlay: Requires an Apple device. Please refer to Apple’s website about using AirPlay. Please note that iOS 11.4 or later is required.

Chromecast Built-In: This is supported by many devices and apps including, but not limited to, Android devices. Many apps support Google

Cast and some TV’s have Google Cast built-in. Please refer to Google’s website for information about using Google Cast.

Spotify Connect: Supported in the Spotify App only, but on multiple platforms.

Ready to play some music?

Listen on your speakers or TV, using the Spotify app as a remote.

Learn More: https://www.spotify.com/int/connect/

Bluetooth playback

Switch to “Bluetooth mode” rst (System LED will turn blue). Then make sure your device has established the Bluetooth connection to the

speaker. Now you are ready to play music.

AUX playback

Simply switch the speaker to “AUX mode” (System LED will turn green) and connect a device to the AUX-input on the back of the speaker.

Note: Remember that in this mode you can control the volume on your device as well as on the speaker.

USING YOUR SPEAKER FOR PLAYBACK

14

Safety

• Only use a compatible power source to power the speaker.

• Damages caused by severe heat will risk voiding your warranty.

• Never try to open or repair your JAYS s-Living Flex. It will void warranty and you will risk personal injury. Risk of electric shock.

• Always place your s-Living Flex on a at and stable surface. Failure to do so will increase risk of speaker falling, hence getting damaged

or you might get a personal injury.

• Warning. This product contains magnets which might be harmful to pacemaker wearers.

• Always disconnect your speaker from power before cleaning. Do not use any liquids and chemicals when cleaning.

Statements

EU Declaration of conformity

Hereby Northbaze Distribution AB declares that this product is in compliance with the essential requirements and other relevant provisions of Di-

rective 2014/53/EU and all other EU directive requirements. The complete declaration of conformity can be found at www.jaysheadphones.com.

Caution

Risk of explosions if battery box is damaged or opened. Dispose of used battery according to your local waste disposal authority.

FCC Rules

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including interference that may cause undesired operation.

Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this product does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Please take attention that changes or modication not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This

equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.

RSS standards

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device.

SAFETY INFORMATION & STATEMENTS

15

Environmental information

This product complies with international directives, including but not limited to WEEE Directive (2012/19/EU).

Do not dispose with normal household waste. Please consult your local waste disposal authority for guidance on how to properly recycle or

dispose of this product.

Manufacturer’s limited warranty

Your original Northbaze Distribution AB product is covered by a warranty of twelve (12) months from the date of purchase of a brand new,

unused Northbaze Distribution AB product by the original purchaser. Northbaze Distribution AB guarantees that the product is free from faults

in the materials, design and workmanship when it was sold to the purchaser. If you are not able to submit the receipt when making a warranty

claim you may be obliged to pay for any repairs carried out. Proof of purchase must clearly state the date of purchase, name of the product and

authorized resellers’ details.

The Warranty Period cannot be extended or renewed due to subsequent resale or replacement of the product. This Limited Warranty does not

affect your legal rights under your applicable national laws relating to the sale of consumer electronic products. Defective parts replaced within

the Limited Warranty Claim shall become the property of Northbaze Distribution AB.

What is not covered by the limited warranty?

• Faults caused by wear and tear, age-related battery capacity loss, accidents, dropping, mechanical damage, chemical products, abnormal

impact damage or force majeure.

• Modications or repairs performed by yourself or third party without Northbaze Distribution AB approval.

• The s-Living FLEX is IPX4 rated. This means it is resistant to splashes of water. The speaker is not waterproof meaning it may not be submerged

into water.

How to get warranty service

If you wish to make a Warranty Claim within the Limited Warranty Period, please contact the reseller of your product for further help. You will

need to provide the proof of purchase and the affected part. Any defective parts covered by the Limited Warranty will be repaired or replaced

free of charge. Replaced or repaired parts provided during the Warranty Period will be warranted for the remainder of the original Warranty

Period or for sixty (60) days from the date of repair or replacement, whichever is longer. For FAQ please visit www.jaysheadphones.com.

LEGAL & WARRANTY

16

Kontrollpanel - se nästa sida för bildreferens

1. Håll inne på / av-knappen för att slå på / av din s-Living Flex.

2. Tryck en gång på PLAY/PAUSE-knappen till vänster för att spela eller pausa . Håll inne för att växla mellan Wi-Fi, Bluetooth och AUX.

3. Tryck på + eller - för att justera volymen.

4. När du är i Wi-Fi-läge, håll inne 3 till 6 sekunder för att gå in i WAC-läge. När du är i Bluetooth-läge, håll inne 3 till 6 sekunder för att öppna

Bluetooth-parning. Håll inne 6+ sekunder för att återställa din högtalare.

ANVÄND DIN HÖGTALARE

(SV) Svenska

17

ANVÄND DIN HÖGTALARE

1

2

3

4

18

Kom igång

1. Anslut strömmen till din högtalare. Använd medföljande nätadapter för s-Living Flex och anslut till ett eluttag.

2. Tryck och håll inne ”ON” i 3 sekunder för att slå på högtalaren, vilket tar upp till en minut. Om du behöver stänga av trycker du och håller inne

OFF 3 sekunder igen.

3. När du hör ett röstmeddelande från högtalaren är du redo att fortsätta.

Högtalarlägen

När högtalaren är PÅ och klar kan du växla mellan olika lägen. Håll inne på PLAY / PAUSE-knappen för att växla läge.

Du kan välja:

• Wi-Fi-läge LED-lampan visar LILA färg (detta är standardläge)

• Bluetooth-läge LED-lampan visar BLÅ färg

• AUX-In-läge LED-lampan visar GRÖN färg

STARTA UPP DIN

s-Living Flex

19

Använd din högtalare med batteri

Du kan använda din högtalare med endast batteri i cirka 6 timmar i uppspelningsläge. Därefter måste du ansluta den till det medföljande

eluttaget. Högtalaren går automatiskt till standby-läge om ingen musik spelas under 10 minuter. Om i standby-läge i 60 minuter stängs s-Living

Flex av för att inte tömma batteriet. Om du använder din högtalare i AUX-läge går högtalaren inte automatiskt i standby-läge. När batterinivån är

låg blir LED gul. När du laddar batteriet igen lyser LED-lampan gul. När den är fulladdad igen kommer LED-lampan att återgå till dess lägesfärg.

Notera

Wi-Fi-läge kräver att högtalaren är ansluten till ett Wi-Fi-nätverk. Och detta behövs också om du vill använda Wi-Fi-funktioner som Google Cast,

AirPlay eller Spotify Connect. Dessutom är högtalaren kompatibel med röstassistenter från Google och Apple (Google Assistant och Siri) om

högtalaren också är ”parad” med Google Home och / eller Apple Home (Apple HomeKit). Högtalaren har INTE röstassistentfunktionen inbyggd

direkt.

Viktigt

Om LED-lampan blinkar RÖTT efter uppstart, eller om du plötsligt märker att LED blinkar RÖTT, ska du INTE ta ur strömkontakten. Detta innebär

att högtalaren installerar automatiska programuppdateringar.

STARTA UPP DIN

s-Living Flex

20

Starta

Under start (slå PÅ högtalaren) blinkar LED-lampan snabbt.

Obs! När du slår på högtalaren startar den alltid i Wi-Fi-läge.

Sökläge

När högtalaren är PÅ kommer den att börja med att vara i ”söktillstånd” och försöka söka efter och ansluta till det senaste Wi-Fi-nätverket. Under

detta tillstånd blinkar LED-lampan. Detsamma kommer att hända om högtalaren sätts i “Bluetooth-läge”, där du nu kan upprätta anslutning till en

tidigare parad Bluetooth-enhet.

Uppstartläge eller parkopplingsläge

I ”Wi-Fi-läge” går högtalaren automatiskt in i ”uppstartläge” inom 20 sekunder, om högtalaren under ”sökläge” inte lyckas återansluta till det

tidigare Wi-Fi-nätverket.

I “uppstartläge” blinkar LED-lampan kontinuerligt. Samma LED-beteende kommer att inträffa om högtalaren är inställd på ”Bluetooth-

parningsläge”.

Uppspelningsläge

Under uppspelning lyser LED-lampan med ett fast sken och färgen på LED-laman (Lila, Blå, Grön) visar vilket “läge” högtalaren är i

(Wi-Fi-uppspelning, Bluetooth-uppspelning, AUX-uppspelning).

Viloläge / standby-läge

LED-lampan ”andas” långsamt vilket indikerar ”ingen åtgärd” eller ”jag sover”.

“Viloläge” kommer att inträffa så snart musiken har pausats (ingen åtgärd).

”Standby-läge” kommer att inträffa om det inte sker någon åtgärd i 20 minuter när den är inkopplad och 10 minuter när den inte är inkopplad.

Om den är i standby-läge i 60 minuter kommer s-Living Flex att stängas av. För att slå på, håll inne ”ON” i tre sekunder.

LED-INDIKATIONER OCH UPPSTART

La page charge ...

JAYS s-Living Flex Manuel utilisateur

JAYS s-Living Flex Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents