Kessil A160WE Mode d'emploi

Marque
Kessil
Modèle
A160WE
Taper
Mode d'emploi
INSTALLATION GUIDE
PARTS DIAGRAM
A160WE
OWNER’S MANUAL
APower Cord
IDC Power Supply
HBracket
CSpectral Tuning Control
FLight Intensity Control
DExternal Controller Port
EVenting Holes
GLens
BMount
PRODUCT SPECIFICATIONS
Illuminator
Listed Power Supply
Power Consumption 40 W maximum
19-24 VDC ± 5% Input Voltage
Input
Output
100-240 VAC 50-60 Hz
19 VDC, maximum 3.42A
24 VDC, maximum 2.10A
SAFETY INSTRUCTIONS
1. DO NOT use a power supply that is
outside the specifications. This is a fire
hazard and may lead to unit failure.
2. DO NOT use outdoors. This unit is
intended for indoor use only.
3. DO NOT expose unit to an extremely
humid environment or submerse unit in
water. This may lead to unit failure.
4. DO NOT place working illuminator in
close contact with any objects. This
may cause the objects to heat up and
the unit to overheat.
5. KEEP lens away from sharp objects.
This may break the lens and lead to
unit failure.
6. DO NOT cover or place objects on the
power supply. Power supply should not
be contained in an airtight space.
INSTRUCTIONS DE SECURITE
1. N’UTILISEZ PAS de câble d’alimentation
ne correspondant pas aux
caractéristiques. Il y aurait un risque
d’incendie et de dommages de l’unité.
2. NE PAS UTILISER à l’extérieur. Cette
unité est prévue pour une utilisation en
intérieur.
3. N’EXPOSEZ PAS l’unité à un
environnement extrêmement humide ou
ne submergez pas l’unité dans l’eau.
Cela pourrait endommager l’unité.
4. NE PLACEZ PAS l’illuminateur en
marche, en contact direct avec d’autres
objets. Cela pourrait causer un
réchauffement trop élevé de ces
derniers et pourrait faire surchauffer
l’unité.
5. GARDEZ la lentille (H) à l‘écart des
objets pointus. Les objets pointus
pourraient casser la lentille et
endommager l’unité.
6. NE RECOUVREZ PAS, ou ne placez
pas d’objet sur le câble d’alimentation.
Le câble ne doit pas se trouver dans un
espace fermé.
1. Remove contents from package.
2. Secure designated mount (B) to unit
with screws, and screw gooseneck to
attach mount (gooseneck sold separately).*
3. Hang the A160WE 1 to 2 ft. above the
object to be illuminated.**
4. Connect power cord (A) to the specified
DC power supply (I).
5. Plug the power supply into an outlet
with the correct specifications (see
product specifications for more
information).
6. Adjust the Light Intensity Control (F)
and the Spectral Tuning Control (C) to
the desired setting. A160WE Tuna Blue
tunes from 10,000K - Actinic. A160WE
Tuna Sun tunes from 6,000K - 9,000K.
7. The jacks beneath the controls can be
connected to an external 0~10V controller.
Please consult your controller’ s owners
manual for more information.
* The A160WE may also be hung by mounting
two metal hooks (diameters of at least 2.5
mm and thread numbers of at least 6) through
its brackets (H).
** The A160WE should only be installed on
wood, acoustic tile or other similar materials.
** For sufficient airflow, the venting holes (E)
should be at least 12 in. from surrounding
obstructions.
210914A3
TROUBLESHOOTING GUIDE
Problem
Light doesn’t turn ON
Unit is flickering
Solution
Make sure the unit is connected to the power supply and the power
supply is connected to an outlet with the correct specifications.
Make sure you are using a power supply with the correct specifications.
Make sure the unit has not overheated by operating at a room
temperature exceeding 40°C.
Make sure electrical power is available to the AC outlet being used.
Make sure the power supply has the right specifications.
Make sure the device is operating within the specified operating
temperature range. If unit overheats, it will automatically shut down.
Make sure the fan is operating properly.
Controllability
Multiple A160WE lights can be controlled by either a single
external 0~10V controller or manually.
MAINTENANCE
1. Keep the air venting holes (E), and fan clear of dust. To clean the fan, unplug the unit
and insert the tip of a CO2 dust blower (or similar dust blower) in one of the venting
holes (E) on the unit's outer shell. Hold and spray. You can also gently vacuum the
light through the venting holes.
2. Keep the lens (G) clean. If the lens becomes contaminated with water, dust, or other
particles, unplug the unit and clean the lens with isopropyl alcohol. Wet a cotton swab
or a napkin in isopropyl alcohol, gently wipe the surface of the lens, and let it dry.
CABLES
Available cables:
• Control Cable (Please consult kessil.com
for list of available cables and compatible
controllers).
• Unit Link Cable (6' male/male with 3.5 mm
stereo jack).
• Control Extension Cable (6' male/female
with 3.5 mm stereo jack).
STARTING A CHAIN
Connect two or more lights with the Kessil
Link Cable, as shown to the above.
CONTROL METHODS
There are two ways to control a chain of lights:
• With an external controller;
• Without external controller (Tuning Controls
on first light control all other lights in chain).
Should a longer cable be needed, the Kessil
Extension Link Cable may be used.
Each light has its own independent power
supply. Any number of lights can be daisy
chained together without degradation of
signal. However, in longer chains a slight
delay in response may occur. Manual tuning
is disabled when device senses input cable.
OutputInput
To next light Input from Controller
Light Intensity ControlUnit Link CableSpectral Tuning Control
This is a LED light source emitting 40 % or more of total
radiation power of the range 250-800 nm in the range of
400-480 nm, and intended for coral growth.
@kessilled
@kessil
kessil.com
kessil.led
kessiltube
  • Page 1 1
  • Page 2 2

Kessil A160WE Mode d'emploi

Marque
Kessil
Modèle
A160WE
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents