Bercomac 700457 700458 Manuel utilisateur
- Catégorie
- Moteur
- Taper
- Manuel utilisateur
1
BERCO
Subframe with Electric Lift & Drive Mechanism
for
HUSQVARNA, JONSERED, POULAN, RALLYE, WEEDEATER & YARD PRO
tractors
*104837_EN*
CAUTION:
READ & FOLLOW ALL SAFETY RULES & INSTRUCTIONS BEFORE
OPERATING YOUR EQUIPMENT
104837_EN I-12
* ASSEMBLY * REPAIR PARTS
* OPERATION * MAINTENANCE
OWNER’S MANUAL
Model Number
700457 Subframe with Winch
700458 Compact Drive Mechanism
700459 Northeast Drive Mechanism
2
LIMITED WARRANTY
Bercomac Limitée
92, Fortin North, Adstock, Quebec, Canada, G0N 1S0
Conditions and Products Covered:
BERCOMAC guarantees any part of the product or accessory
manufactured by BERCOMAC and found in the reasonable
judgment of BERCOMAC to be defective in material and or
workmanship will be repaired or replaced by an authorized
dealer without charge up to our maximum labor rates and pre-
established times. For replacement parts only standard ground
freight services are covered. This warranty extends to the
original retail purchaser only and is not transferable to any
subsequent purchasers.
Warranty Period
(from date of the original retail purchase):
• Residential use: 1 year
• Commercial or rental use: 90 days
Exceptions Noted Below; the following items are guaranteed
by the original manufacturer and have their own warranty,
conditions and limited time:
• Tire Chains: 90 days
• Engines (installed in factory on BERCO equipment): 2 years
• Engines (sold separately): Validate with the dealer.
Please refer to the engine manufacturer’s warranty
statement included with the unit. BERCOMAC is not
authorized to handle warranty adjustments on engines.
Items and Conditions NOT Covered:
This warranty does not cover the following:
• Pick-up or delivery charges or in-home services fees.
• Any damage or deterioration of the unit, parts and or finish
of these due to normal use, wear and tear, or exposure.
• Cost of regular use or maintenance service or parts, such as
gas, oil, lubricants, tune-up parts, and adjustments.
• Any part or accessory which has been altered, modified,
misused, neglected, accidentally damaged or not properly
installed, maintained, stored or repaired not in accordance
with the instructions in the owner’s manual.
• Repair due to normal wear and or any wear items such as
shear pins, bolts, belts, etc.
• Expedited freight fee services for replacement parts.
• Shear bolts and shear pins are to be considered as a
preventive measure not as an assured protection, any
damages resulting from the lack of shear bolts breakage are
not covered.
NOTE: All warranty work must be performed by an authorized
dealer using original (manufacturer) replacement parts.
Owner’s Responsibilities:
BERCOMAC’s defective equipment or part must be returned
to an authorized dealer within the warranty period for repairs.
In the event that defective merchandise must be returned to
manufacturer for repairs, freight fees are prepaid and a written
authorization from BERCOMAC must be obtained by dealer
prior to the shipment. This warranty extends only to
equipment operated under normal conditions. To validate a
warranty claim, it is the user’s responsibility to maintain and
service the unit as specified in the owner’s manual or to have
the unit serviced at their dealer at their expense.
General Conditions:
The sole liability of BERCOMAC with respect to this warranty
shall be strictly and exclusively repair and replacement as
mentioned herein. BERCOMAC shall not have any liability for
any other costs, loss or damage, including but not limited to,
any incidental or consequential loss or damage.
In particular, without being limited to, BERCOMAC shall have
no liability or responsibility for:
• Travel time, overtime, after hours time or other
extraordinary repair charges or relating to repairs and or
replacements outside of normal business hours.
• Rental of like or similar replacement equipment during the
period of any, repair or replacement work.
• Any communicating or travel charges.
• Loss or damage to person or property other than that
covered by the terms of this warranty.
• Any claims for lost revenue, lost profit or any similar costs
as a result of damage or repair.
• Attorney’s fees.
BERCOMAC’s responsibility in respect to claims is limited to
making the required repairs or replacement without charge up
to our maximum labor rates and pre-established times and no
claim of breach of warranty shall be cause for cancellation or
rescission of the contract of sale of any product or accessory.
This warranty gives you specific legal rights. You may also
have other rights, which vary from state to state.
NOTE: Bercomac reserves the right to change or improve the design of any part or accessory without assuming any obligation to modify
any product previously manufactured.
Instructions for Obtaining Warranty Services:
Contact dealer where equipment was purchased or any other BERCOMAC service dealer to arrange service at their dealership. To
locate a dealer convenient to you, access our website at www.bercomac.com.
Don't forget to bring the product and your proof of
purchase (sales receipt) to the BERCOMAC dealer.
1
TABLE OF CONTENTS
INTRODUCTION ................................................................................................................................................... 2
SAFETY PRECAUTIONS ..................................................................................................................................... 3
SAFETY DECALS ................................................................................................................................................. 5
ASSEMBLY
Tools Required ........................................................................................................................................ 6
Step 1: Subframe Installation .................................................................................................................. 6
Step 2: Installation the Control Assembly ............................................................................................... 9
Step 3: Drive Mechanism Installation ..................................................................................................... 12
OPERATION & MAINTENANCE
Controls .................................................................................................................................................... 15
Maintenance ............................................................................................................................................ 15
Belt Replacement .................................................................................................................................... 15
Verify Tire Pressure ................................................................................................................................. 15
DISMOUNTING & STORAGE
Dismounting ............................................................................................................................................. 16
Storage .................................................................................................................................................... 16
TORQUE SPECIFICATION TABLE ..................................................................................................................... 17
PARTS BREAKDOWN AND PARTS LIST
Compact Drive Mechanism 700458 ....................................................................................................... 18
Northeast Drive Mechanism 700459 ...................................................................................................... 20
Subframe 700457 .................................................................................................................................... 22
ATTACHMENTS ................................................................................................................................................... 25
PAGE
2
INTRODUCTION
TO THE PURCHASER
This new accessory was carefully designed to give years of dependable service. This manual has been provided to
assist in the safe operation and servicing of your attachment.
NOTE: All photographs and illustrations in the manual may not necessarily depict the actual models or attachment, but
are intended for reference only and are based on the latest product information available at the time of publication.
Familiarize yourself fully with the safety recommendations and operating procedures before putting the machine to
use. Carefully read, understand and follow these recommendations and insist that they be followed by those who will
use this attachment.
THIS SAFETY ALERT SYMBOL IDENTIFIES AN IMPORTANT SAFETY MESSAGE IN THIS
MANUAL THAT HELPS YOU AND OTHERS AVOID PERSONAL INJURY OR EVEN DEATH.
DANGER, WARNING, AND CAUTION ARE SIGNAL WORDS USED TO IDENTIFY THE LEVEL OF
HAZARD. HOWEVER, REGARDLESS OF THE HAZARD, BE EXTREMELY CAREFUL.
DANGER: Signals an extreme hazard that will cause serious injury or death if recommended precautions
are not followed.
WARNING: Signals a hazard that may cause serious injury or death if the recommended precautions are
not followed.
CAUTION: Signals a hazard that may cause minor or moderate injury if the recommended precautions are
not followed.
Record your attachment serial number and purchase date in the section reserved below (there is no serial number on
the subframe). Your dealer requires this information to give you prompt, efficient service when ordering replacemen
t
parts. Use only genuine parts when replacements are required.
If warranty repairs are required please present this registration booklet and original sales invoice to your selling deale
r
for warranty service.
This manual should be kept for future reference.
Please check if you have received all the parts for your kit with the list of the
bag and the list of the box.
SERIAL NUMBER : ___________________________
(IF APPLICABLE)
MODEL NUMBER: ___________________________
PURCHASE DATE : ___________________________
3
SAFETY PRECAUTIONS
Careful operation is your best insurance against an accident. Read this section carefully before operating the vehicle
and accessory. This accessory is capable of amputating hands and feet and throwing objects. Failure to observe the
following safety instructions could result in serious injury. All operators, no matter how experienced they may be,
should read this and other manuals related to the vehicle and accessory before operating. It is the owner's legal
obligation to instruct all operators in safe operation of the accessory.
GLOSSARY:
In this manual, right and left sides are determined by
sitting on the seat of the vehicle facing forward.
In this manual, "accessories" means attachments
(snowblower, rotary broom, blade etc.) that you install
on the vehicle (lawn tractors, A.T.V. s etc).
TRAINING:
This symbol, "Safety Alert Symbol", is used
throughout this manual and on the
accessory’s safety labels to warn of the
possibility of serious injury. Please take
special care in reading and understanding
the safety precautions before operating the
vehicle and accessory.
1. Read this owner's manual carefully. Be thoroughly
familiar with the controls and proper use of the
vehicle and accessory. Know how to stop the unit
and disengage the controls quickly.
2. Never allow children to operate the vehicle nor the
accessory. Never allow adults to operate the vehicle
nor the accessory without proper instructions.
3. No one should operate the vehicle nor the
accessory while intoxicated or while taking
medication that impairs the senses or reactions.
4. Keep the area of operation clear of all people,
particularly small children and pets.
PREPARATION:
1. Thoroughly inspect the area where the accessory
is to be used and remove door mats, all foreign
objects and the like.
2. For motorized accessories, disengage all clutches
and shift into neutral before starting engine.
3. Do not operate the accessory without wearing
adequate winter outer garments. Avoid loose fitting
clothing that can get caught in moving parts. Wear
footwear that will improve footing on slippery
surfaces.
4. Handle fuel with care, it is highly flammable.
a) Use approved fuel container.
b) Never add fuel to a running engine or hot engine.
c) Fill fuel tank outdoors with extreme care. Never fill
fuel tank indoors.
d) Never fill containers inside a vehicle, or on a
truck or a trailer bed with a plastic liner. Always
place containers on the ground, away from your
vehicle, before filling.
e) When practical, remove gas-powered
equipment from the truck or trailer and refuel it
on the ground. If this is not possible, then refuel
such equipment on a trailer with a portable
container, rather than from a gasoline
dispenser nozzle.
f) Keep the nozzle in contact with the rim of the
fuel tank or container opening at all times, until
refueling is complete. Do not use a nozzle lock-
open device.
g) Replace fuel cap securely and wipe up spilled
fuel.
h) If fuel is spilled on clothing, change clothing
immediately.
5. Never attempt to make any adjustments while the
engine (motor) is running (except when specifically
recommended by manufacturer).
6. Let the vehicle and accessory adjust to outdoor
temperatures before starting to clear snow.
7. Never use an accessory without proper guards,
plates, or other safety protective devices in place
8. Always make sure to wear the appropriate safety
equipment required (glasses, muffs, mask…) for
each type of product. See operation section.
9. Always make sure of having safe traction on the
vehicle by using the recommended accessories
(chains, A.T.V. tracks, counterweights…). See
operation section.
10. Never modify the accessory or any part without
the written consent from the manufacturer.
4
OPERATION:
1. Do not put hands or feet near, under or inside rotating
parts.
2. Exercise extreme caution when operating on or
crossing gravel drives, walks or roads. Stay alert for
hidden hazards or traffic. Do not carry passengers.
3. After striking a foreign object, stop the engine (motor),
disconnect the wire from the spark plug(s) and keep
wire away to prevent accidental starting. Thoroughly
inspect the accessory for any damage and repair
damage before restarting and using the accessory.
4. If the unit should start to vibrate abnormally, stop the
engine (motor) and check immediately for the
cause. Vibration is generally a warning of trouble.
5. Take all possible precautions when leaving the
vehicle unattended. Disengage the power take-off,
lower the attachment, place the transmission into
neutral, set the parking brake, stop the engine and
remove the contact key.
6. Do not run the engine indoors, except when starting
the engine and for transporting in or out of the
building. Do not operate or let motor run in a storage
area without ventilation because gas contains
carbon monoxide which is odorless, colorless and
can cause death.
7. Never clean across the face of slopes, go from top
to bottom. Exercise extreme caution when using
equipment on slopes. Do not attempt to clear a
steep slope.
8. Never tolerate bystanders in the working zone.
Never use an accessory in the direction of
bystanders, it might throw gravel or debris that can
hurt people or damage property.
9. Never operate the accessory at high transport
speeds on slippery surfaces. Use care when
backing up.
10. Do not carry passengers.
11. Disengage power to the accessory when it is
transported or not in use.
12. Never operate the accessory without good visibility
or light.
14. Keep the accessory away from heat sources or
flames.
MAINTENANCE AND STORAGE
1. When cleaning, repairing or inspecting the vehicle
and accessory, make certain that all moving parts
have stopped. Disconnect wire from the spark
plug(s) and keep wire away to prevent accidental
starting.
2. Check all the bolts and components at frequent
intervals to make sure that they are properly
tightened.
3. Never store a motorized accessory with fuel in the
fuel tank inside a building where ignition sources are
present such as hot water and space heaters,
clothes dryers, and the like. Allow the engine to cool
before storing in any enclosure.
4. Always refer to the owner’s manual when you store
the accessory and vehicle for a prolonged or an
unspecified length of time.
5. Maintain or replace safety and instruction labels, as
necessary.
6 For winter accessories, (if applicable), let the engine
run for a few minutes after clean snow in order to
prevent the rotary parts from freezing.
7. Inspect the vehicle’s and accessory’s air filter every
day. Clean it or replace it as necessary. Change the
oil more often when working in dusty conditions.
See the vehicle’s and accessory's owner’s manual.
THIS SYMBOL MEANS
DANGER !
BECOME ALERT !
YOUR SAFETY IS INVOLVED !
SAFETY PRECAUTIONS
5
SAFETY DECALS
REPLACE IF DECALS ARE DAMAGED
SEE PARTS BREAKDOWN FOR DECAL LOCATION
DECAL #105133
To avoid serious injuries:
Keep hands away from the hot surface.
6
ASSEMBLY
Install the supports (item 5) on each side of the
vehicle.
Item # Description Action
1 Carriage bolt,
3/8 x 1’’ (qty 6) Insert as shown.
2 Carriage bolt,
5/16 x 1’’ (qty 2) Insert as shown.
*3 Flat washer 1/2’’,
(qty 6) See*
*4 Flat washer 7/16’’,
(qty 2) See*
5 Support
(qty 2) Install on the
bolts as shown.
6 Flange nut 3/8’’,
(qty 6) Do not tighten
now.
7 Flange nut 5/16’’,
(qty 2) Do not tighten
now.
*If necessary, use the flat washers to keep the
supports flat on the vehicle‘s frame.
IMPORTANT: TORQUE ALL BOLTS ACCORDING
TO TORQUE SPECIFICATION TABLE WHEN
STATED: TIGHTEN FIRMLY.
THE WINCH KIT IS TO BE USED ONLY TO LIFT
BERCO ACCESSORIES, ANY OTHER USE MAY
CAUSE DAMAGE TO THE VEHICLE.
This subframe may be used to install different
attachments (see attachments page). Once installed,
it may remain permanently on your vehicle.
NOTE:It is not necessary to remove mower deck at
this step.
STEP 1
SUBFRAME INSTALLATION:
Refer to parts breakdown section for parts
identification.
TOOLS REQUIRED:
Wrenches: 5/16, 7/16, 9/16, 1/2, 10mm
Ratchet
Sockets: 9/16, 1/2
Pliers
Square head screwdriver: #2
1 wrench (for the nuts on the battery posts of the
vehicle)
Optional tools according to the year of the
vehicle:
Drill
Bit: 13/32
Punch
Hammer
Install the supports
7
ASSEMBLY
Install the female hitch between the two supports
Install the female hitch (item 1)
# Item Description Action
2 Hex bolt 3/8 x 1’’
(qty 4) Insert as shown.
3 Flange nut 3/8’’
(qty 4) Tighten the all the
nuts firmly.
1 Female hitch Install between the
two supports.
Install the spring (item 1)
# Item Description Action
1 Spring Install the spring
on the frame as
shown.
NOTE: The latch must move freely.
Install the spring as shown
8
Install the handle support (item 3) on the left side.
# Item Description Action
1 Carriage bolt
3/8 x 1’’ (qty 2) Insert the bolts as
shown.
*2 Flat washer 1/2’’ See *
3 Handle support Install as shown.
**4 Thread cutting screw
3/8 x1’’ See **
6 Flange nut 3/8’’
(qty 2) Tighten the nuts.
7 Plastic grommet Insert as shown.
8 Square head set
screw 5/16 x 1/2’’ Insert in the hole of
the handle.
* If necessary use a flat washer to keep the support flat
on the tractor frame.
** Use this screw if the bottom hole is threaded.
NOTE: If tractor is equipped with a belt guide, remove
and install it under the handle support with the bolts in
the kit (do not put the flat washer (item 2) .
5 Flat washer 3/8’’
(qty 2) Install as shown.
ASSEMBLY
Install the handle support
Install the cab support (item 3) on the right side.
# Item Description Action
1 Carriage bolt
3/8 x 1’’ (qty 2) Insert the bolts as
shown.
*2 Flat washer 1/2’’ See *
**4 Thread cutting screw
3/8 x1’’ See **
6 Flange nut 3/8’’
(qty 2) Tighten the nuts.
7 Square head set
screw 5/16 x 1/2’’ Insert in the hole of
the handle.
* If necessary use a flat washer to keep the support flat
on the tractor frame.
** Use this screw if the bottom hole is threaded.
3 Cab support Install as shown.
NOTE: If tractor is equipped with a belt guide, remove
and install it under the cab support with the bolts in the
kit (do not put the flat washer item 2) .
5 Flat washer 3/8’’
(qty 2) Install as shown.
Install the cab support
9
ASSEMBLY
Install the relay
Install the support and winch control
STEP 2:
INSTALLATION OF THE CONTROL
ASSEMBLY
Install the relay (item 1).
#
Item Description Action
2 Metal screw
#12 x 3/4’’ (qty 4) Secure relay in place.
*3 Nylon tie wrap 8’’
(qty 4) See *
* If necessary use the nylon tie wraps to secure the
relay in place.
1 Relay Install in an appropriate
area.
Install the control support (item 1)
# Item Description Action
1 Control support Install in an
appropriate area.
2 Metal screw
#8 x 1/2’’ (qty 2) Secure the support in
place.
3 Winch control Insert in the support.
10
ASSEMBLY
CONNECTING THE WIRES
NOTE:The posts on the relay are identified by
numbers. (1-2-3-4).
Install the wires from the winch on the posts of the
relay.
Red wire (+) on post #3.
Black wire (-) on post #4.
Connect the green wire from the winch (limit switch)
with the green wire from the relay.
Connect the wires
IDENTIFY THE IGNITION WIRE:
Place the clip of the Hi / Low tester on the negative
post (-) on the battery or a metal surface without any
paint.
Turn the ignition key to the position, accessory.
Insert the tip of the tester in a hole at the back of the
starter (switch) make sure to touch the metal part of
the wire.
If the tester’s light turns on , turn the ignition key to
the position, Off. The light must turn off.
You have identified the ignition wire, if not repeat the
operation on another wire.
INSTALL THE CONTROL WIRE:
Join the ignition wire and the red wire from the control
(item 1) with the instant connector (item 2).
Connect the black wire of the control to the black wire
on the relay.
Connect the green wire of the control with the green
wire of the winch (limit switch).
Connect the ignition wire
11
ASSEMBLY
CAUTION
FOR YOUR SECURITY:
Read and follow the safety precautions for the
battery in the vehicle’s manual.
CONNECT THE WIRES ON THE BATTERY:
Connect the wires from the relay to the vehicle’s
battery.
The red wire (+) on the positive post of the battery
(item 1).
The black wire (-) on the negative post of the battery
(item 2).
Make sure to tighten the nuts on the posts.
TIE ALL THE WIRES:
NOTE: Make sure the wires from the control
assembly do not interfere with anything on the tractor
nor come into contact with any heating, electrical or
removable elements of the tractor.
Tie the wires with four nylon tie wraps included in the
kit.
Connect the relay wires to the battery
Install the heat shield (item 1).
# Item Description Action
2 Hex bolts 1/4 x 1/2’’
(qty 2) Tighten firmly.
1 Heat shield Install as shown.
Install the heat shield
12
ASSEMBLY
STEP 3:
DRIVE MECHANISM INSTALLATION: WARNING
TO PREVENT INJURIES:
It is the person who installs the drive mechanism
responsibility to make sure that when the clutch
is disengaged that all moving parts stop.
For more information, do not hesitate to contact
the technical support.
WARNING
TO PREVENT INJURIES:
Stop the motor.
Apply parking brake.
Remove the ignition key.
Disconnect the wire from the spark plug(s) and
keep away from spark plug(s) to prevent accidental
starting.
NOTE: You must remove mower deck to install
the drive mechanism.
Install the support (item 2) on each side.
# Item Description Action
1 Carriage bolt
3/8 x 3/4’’ (qty 4) Insert as shown.
2 Support (qty 2) See*
3 Flange nut 3/8’’
(qty 4) Tighten firmly.
*Choose the appropriate holes in the supports and
make sure that there is no interference between the
pin and the parts of the vehicle. Install the supports
The next two instructions are for vehicles
that do not have pins that are used as
supports for the mower deck.
Use the drilling template to drill a hole on each side of
the vehicle.
Drill a hole if applicable
Install the sleeves
Install the sleeve (item 1) on each side.
# Item Description Action
1 Sleeve (qty 2) Install as shown.
2 Hex bolt 3/8 x 1
1/4’’ (qty 2) Insert in the sleeve.
3 Flange nut 3/8’’
(qty 2) Tighten firmly.
13
ASSEMBLY
For tractors with Electric Clutch:
Install the belt on the engine pulley of the vehicle.
Check the tension on the spring.
If necessary, adjust the tension by moving the
adjustment rod (item 1) and tighten the set screw
(item 2). No modifications to be done
For tractors with Manual Clutch activated by a
cable:
Install the tractor’s manual clutch cable .
* Remove the spring.
# Item Description Action
1 Spring from the clutch
cable Install as shown in the
hole on the tension
pulley.
2 Clutch cable Insert in the slot on the
adjustment rod.
3 Hair pin 2mm Secure the cable.
4 Adjustment rod Slide towards the back
to apply enough tension
on the spring.
5 Square head set
screw 5/16 x 1/2’’ Secure the adjustment
rod.
Install the belt on the engine pulley of the vehicle.
Check the tension on the spring.
If necessary, adjust the tension by moving the
adjustment rod and tighten the set screw. Install the manual clutch cable
Install the drive mechanism
Install the drive mechanism (item 1).
# Item Description Action
1 The front end of drive
mechanism Hook on the pins.
2 The back end of
drive mechanism Install between the
supports.
3 Pin Insert as shown.
4 Hair pin Secure the pin.
14
ASSEMBLY
IMPORTANT: Adjust the height of the three supports
(items 1, 2 and 3) to make sure the drive mechanism
pulley (item 4) is aligned with the engine pulley (item
5) more or less 1/8’’.
If applicable, you can remove or add a flat washer on
the tension pulley (item 6) for a better adjustment.
Engage and disengage the clutch a few times and
make sure the belt does not touch the belt guide in
any place when the drive mechanism is engaged.
VERIFICATION OF THE BELT AND PULLEY
ALIGNMENT:
WARNING
TO PREVENT INJURIES:
It is the person who installs the drive mechanism
responsibility to make sure that when the clutch
is disengaged that all moving parts stop.
For more information, do not hesitate to contact
the technical support.
WARNING
TO PREVENT INJURIES:
do this verification when the engine of the vehicle
is not running.
Adjust the supports
Adjust the pulleys
15
OPERATION & MAINTENANCE
CAUTION
Read the vehicle Owner’s Manual carefully. Be
thoroughly familiar with the controls & proper
use of the attachment. Know how to stop the
attachment quickly.
CONTROLS
IMPORTANT:
In order to avoid damage to the battery of the
vehicle, always start the engine before using the
winch.
THE SWITCH OF THE WINCH
Press on the switch of the winch to lift or lower the
accessory to the ground.
There is a stopper that limits the lifting or the lowering
of the accessory.
IMPORTANT:
THE WINCH KIT IS TO BE USED ONLY TO LIFT
BERCO ACCESSORIES, ANY OTHER USE MAY
CAUSE DAMAGE TO THE VEHICLE.
MAINTENANCE
a) Check mounting bolts at frequent intervals for
proper tightness to be sure equipment is in safe
working condition.
b) Apply oil at all pivot points.
c) To prolong the life span of the winch, make sure the
limit switch works well.
BELT REPLACEMENT
Belt for the accessories:
SEE ATTACHMENT OWNER'S MANUAL
(SNOWBLOWER AND BROOM ) FOR REPLACING
INSTRUCTIONS.
Drive Mechanism Belt:
a) Dismount the drive mechanism.
b) Remove the bolt which retains the tension pulley.
c) Replace the belt and re-install the tension pulley.
Before tightening make sure the belt guide does
not touch the belt at any time.
d) Re-install the drive mechanism.
e) Check the alignment of the belt that joins the
drive mechanism to the engine pulley.
VERIFY TIRE PRESSURE:
Check and adjust tractor tire pressure as follows:
Front tires: 14-15 psi
Back tires: 7-8 psi
Tire pressure must be even on both sides of the
tractor.
16
DISMOUNTING & STORAGE
DISMOUNTING
SEE ATTACHMENT OWNER'S MANUAL
(SNOWBLOWER, BROOM AND BLADE) FOR
DISMOUNTING INSTRUCTIONS.
a) Dismount the attachment.
b) Remove the rear counterweight when you remove
the front attachment (if applicable).
c) Remove the belt from the engine pulley.
d) Dismount the drive mechanism by supporting it in
hand and removing the hair pin and the pin.
Carefully lower to the ground. Remove the V-belt
from engine pulley.
Manual clutch activated by cable:
Unhook cable shield by removing the hair pin.
Unhook spring. Pull out drive mechanism from
underneath tractor.
e) You may leave the subframe on tractor all year long
or remove it if preferred.
f) Reinstall mower if needed.
STORAGE
a) Clean and paint all parts from which paint has worn.
b) Apply oil at all pivot points.
c) Inspect and replace all defective parts before using
again.
17
TORQUE SPECIFICATION TABLE
GENERAL TORQUE SPECIFICATION TABLE
USE THE FOLLOWING TORQUES WHEN SPECIAL TORQUES ARE NOT GIVEN
NOTE: These values apply to fasteners as received from supplier, dry or when lubricated with normal oil. They do not
apply if special graphited or moly disulphide greases or other extreme pressure lubricants are used. This applies to
both UNF and UNC threads.
*
Thick nuts must be used with grade 8 bolts
SEE Grade No.
2 5 8 *
BOLT HEAD
IDENTIFICATION
MARKS AS PER GRADE
NOTE MANUFACTURING
MARKS WILL VARY
TORQUE TORQUE TORQUE
BOLT SIZE FOOT POUNDS NEWTON-METERS FOOT POUNDS NEWTON-METERS FOOT POUNDS NEWTON-METERS
Inches Millimetre
Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Max.
Min. Max. Max.
1/4" 6.35 5 6 6.8 8.13 9 11 12.2 14.9 12 15 16.3 30.3
5/16" 7.94 10 12 13.6 16.3 17 20.5 23.1 27.8 24 29 32.5 39.3
3/8" 9.53 20 23 27.1 31.2 35 42 47.5 57 45 54 61 73.2
7/16" 11.11 30 35 40.7 47.4 54 64 73.2 86.8 70 84 94.9 113.9
1/2" 12.7 45 52 61 70.5 80 96 108.5 130.2 110 132 149.2 179
9/16" 14.29 65 75 88.1 101.6 110 132 149.2 179 160 192 217 260.4
5/8" 15.88 95 105 128.7 142.3 150 180 203.4 244.1 220 264 298.3 358
3/4" 19.05 150 185 203.3 250.7 270 324 366.1 439.3 380 456 515.3 618.3
7/8" 22.23 160 200 216.8 271 400 480 542.4 650.9 600 720 813.6 976.3
1" 25.4 250 300 338.8 406.5 580 696 786.5 943.8 900 1080 1220.4 1464.5
METRIC BOLT TORQUE SPECIFICATIONS
COARSE THREAD
Size Screw Grade No. Pitch
(mm)
Foot Pounds Newton-Meters Pitch
(mm)
Foot Pounds Newton-Meters
M6 4T 1.00 3.6 - 5.8 4.9 - 7.9 - - -
7T 5.8 - 9.4 7.9 - 12.7 - -
8T 7.2 - 10 9.8 - 13.6 - -
M8 4T 1.25 7.2 - 14 9.8 - 19 1.00 12 - 17 16.3 - 23
7T 17 - 22 23 - 29.8 19 - 27 25.7 - 36.6
8T 20 - 26 27.1 - 35.2 22 - 31 29.8 - 42
M10 4T 1.50 20 - 25 27.1 - 33.9 1.25 20 - 29 27.1 - 39.3
7T 34 - 40 46.1 - 54.2 35 - 47 47.4 - 63.7
8T 38 - 46 51.5 - 62.3 40 - 52 54.2 - 70.5
M12 4T 1.75 28 - 34 37.9 - 46.1 1.25 31 - 41 42 - 55.6
7T 51 - 59 69.1 - 79.9 56 - 68 75.9 - 92.1
8T 57 - 66 77.2 - 89.4 62 - 75 84 - 101.6
M14 4T 2.00 49 - 56 66.4 - 75.9 1.50 52 - 64 70.5 - 86.7
7T 81 - 93 109.8 - 126 90 - 106 122 - 143.6
8T 96 - 109 130.1 - 147.7 107 - 124 145 - 168
M16 4T 2.00 67 - 77 90.8 - 104.3 1.50 69 - 83 93.5 - 112.5
7T 116 - 130 157.2 - 176.2 120 - 138 162.6 - 187
8T 129 - 145 174.8 - 196.5 140 - 158 189.7 - 214.1
M18 4T 2.00 88 - 100 119.2 - 136 1.50 100 - 117 136 - 158.5
7T 150 - 168 203.3 - 227.6 177 - 199 239.8 - 269.6
8T 175 - 194 237.1 - 262.9 202 - 231 273.7 - 313
M20 4T 2.50 108 - 130 146.3 - 176.2 1.50 132 - 150 178.9 - 203.3
7T 186 - 205 252 - 277.8 206 - 242 279.1 - 327.9
8T 213 - 249 288.6 - 337.4 246 - 289 333.3 - 391.6
FINE THREAD
18
PARTS BREAKDOWN
COMPACT DRIVE MECHANISM 700458
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Bercomac 700457 700458 Manuel utilisateur
- Catégorie
- Moteur
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Bercomac 700457 700458 User manual
Documents connexes
-
Bercomac 700469-2 700471-1 700471-2 Manuel utilisateur
-
-
-
-
-
-
-
-
-
