INSTALLATION MANUAL
SM-CB-F-XL / SM-CB-T-XL
Strong™ Universal Fixed and Tilt Mount
for Large and Extra Large Displays
SM-CB-F-XL
SM-CB-T-XL
2
Installation Manual
© 2019 Strong
WARNINGS:
• These wall mounts are intended for use only with the maximum weight capacities listed below.
• Installation by a qualied professional is highly recommended for this product.
• Do not begin installation until you have thoroughly read and understand these instructions.
• Ensure the mounting wall will safely support four times the combined weight of the mount and display panel.
• The manufacturer does not accept responsibility for incorrect installation.
CAUTION:
Use with heaver than the maximum weight indicated may result in instability which could possibly cause injury.
AVERTISSEMENTS:
• Ces supports muraux sont pour être utilisés seulement avec les capacités de poids maximales ci-dessous.
• L'installation par un professionnel qualié est fortement recommandée pour ce produit.
• Ne commencez pas l'installation avant d'avoir lu et compris ces instructions.
• Assurez-vous que le mur de montage supporte en toute sécurité quatre fois le poids total du support et du panneau
d'achage.
• Le fabricant n'accepte aucune responsabilité pour une installation incorrecte.
MISE EN GARDE:
Une utilisation avec un poids plus haut que le poids maximal indiqué peut provoquer une instabilité et ainsi des
blessures.
Specications Tools Required Box Contents
• Wall Plate (1)
• Arm Left (1)
• Arm Right (1)
• Hardware Kit
• Power Drill
• 5/16" and 3/32" Drill bit
• Phillips Head Screw Driver
• Level
• Socket Wrench with 1/2 Socket head
• Maximum Weight
• SM-CB-T-XL, SM-CB-F-XL: 200 lbs
• Tilt Range (Tilt Models Only)
• +12°/-5°
• Post Install Adjustment: 0.40"
Fixed & Tilt
Horizontal Measurement (mm)
50 75 100 200 300 400 500 600 700 800
Vertical Mesasurement
(mm)
50 M, L, XL M, L, XL M, L, XL M, L, XL M, L, XL M, L, XL L, XL L, XL XL XL
75 M, L, XL M, L, XL M, L, XL M, L, XL M, L, XL M, L, XL L, XL L, XL XL XL
100 M, L, XL M, L, XL M, L, XL M, L, XL M, L, XL M, L, XL L, XL L, XL XL XL
200 M, L, XL M, L, XL M, L, XL M, L, XL M, L, XL M, L, XL L, XL L, XL XL XL
300 M, L, XL M, L, XL M, L, XL M, L, XL M, L, XL M, L, XL L, XL L, XL XL XL
400 M, L, XL M, L, XL M, L, XL M, L, XL M, L, XL M, L, XL L, XL L, XL XL XL
500 XL XL XL XL XL XL XL XL XL XL
600 XL XL XL XL XL XL XL XL XL XL
HARDWARE KIT
IMAGE DESCRIPTION ITEM QUANTITY
Lag Bolt
(A) 8 × 63 mm
5
Lag Washer (B) 8.4 × 20 × 2 mm 5
Concrete Anchor (C) 10 × 50 mm 5
Screw (D) M6 × 20 mm 4
Screw (E) M6 × 40 mm 4
Screw (F) M8 × 20 mm 4
Screw (G) M8 × 40 mm 4
Screw (H) M8 × 50 mm 4
Installation Manual
3
Drill holes and
insert anchors.
Place wall arm
assembly plate
over anchor and
secure with
lag bolt.
Tighten all
lag bolts.
Wall Arm
Concrete
Wall
Lag Bolt
Figure 2
Figure 1
Bolts
Bolts
Center of Studs
INSTALLATION:
Step 1: Mount the Wall Bracket Assembly
For Mounting on a Wood Stud Wall
1. Pre-drill holes into two wood studs using a 3/32” drill bit.
Be sure to drill into the center of the studs at least 2-1/2”
deep. The use of a stud finder is highly recommended.
2. Insert four Lag Bolts (A) and Lag Washer (B) into holes
through the Wall Plate and tighten down (Figure 1).
WARNING: Stud sizes must be a minimum of 2"x4" and
covered with no more than 3/8" thick dry wall.
For Mounting on a Concrete Wall
3. Pre-drill holes into concrete using 5/16” drill bits to a
depth of 2-1/2". Insert concrete wall anchors (C) and tap in
with hammer, if necessary (Figure 2).
WARNING: When installing wall arm assembly on cinder
block, verify rst that you have a minimum of 1-3/8” of concrete
thickness to be used for the concrete anchors. Do not drill into
mortar joints! Be sure to mount in a solid part of the block,
generally 1”minimum
from the side of the block. Cinder block
must meet ASTM C-90 specications. It is suggested that a
standard electric drill on slow setting is used to drill the hole
instead of a hammer drill to avoid breaking out the back of the
hole when entering a void or cavity.
CONCRETE must be 2500psi density minimum. Lighter
density concrete may not hold concrete anchor. Make
sure that the supporting surface will safely support the
combined load of the equipment and all attached hardware
and components.
4. Insert four Lag Bolts (A) into the wall anchors (C) through
the Wall Plate. Tighten all bolts.
WARNING: Tighten bolts so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage the
bolts, greatly reducing their holding strength.
www.snapav.com Support: 866.838.5052
IMAGE DESCRIPTION ITEM QUANTITY
Spacer (I) 8.5 × 5 mm 4
Spacer (J) 8.5 × 19 mm 4
Spacer (K) 8.5 × 22 mm 4
M6 Washer (L) 6.4 × 18 × 2 mm
8
M
8 Washer
(M) 8.4 × 20 × 2 mm
8
Allen Key
(N) M4 × 358 x 50 mm
1
© 2019 STRONG™
190703-1300
Step 2: Mount Arms to TV
1. Determine the diameter of the screw (parts D through H) your
TV requires by carefully trying to hand-thread one into the
threaded insert on the rear of the TV. If there is any resistance,
stop immediately.
2. Thread the screw through the washer (L or M), arm, spacer (I,
J, or K), and into the TV.
NOTE: Spacers are commonly needed on TVs with curved backs or
recessed screw inserts.
3. Ensure the arms are installed flat side to TV and are square to
each other after all screws have been installed (Figure 3).
Step 3: Hang TV on to the Wall Plate
Carefully lift the TV to hook the arms over the top lip of the wall
plate. The bottom of the arms will then rest on the top edge of the
locking mechanism. The locking mechanism can be released by
pulling the pull strings down and allowing the TV to slide into place.
Once you release the pull strings the TV will be locked. Do not
release the TV until it is completely connected to the wall plate.
Adjustments:
Adjust Horizontal Level and Tilt
Forward Tilt Adjustment
4. Turn Tilt Adjustment Lever (ratchet) clockwise to tighten grip;
counter-clockwise to loosen grip.
5. Pull Tilt Adjustment Lever (ratchet) away from arm and then
turn Clockwise/counter-clockwise to desired location. Let the
Tilt Adjustment Lever (ratchet) sit in place.
6. Repeat as needed to loosen/tighten the tilt.
Horizontal Adjustment
If display is not horizontally level when mounted, Tilt Adjustment
Screws are included at the top of each arm for micro-adjustments
(Figure 6
). Use provided Allen Key to raise or lower the screw,
which will in turn raise or lower the mount.
NOTE: Caution should be taken to avoid any slips or drops to avoid
damage and/or injuries.
Lifetime Limited Warranty
Strong™ Mounts have a Lifetime Limited Warranty. This warranty
includes parts and labor repairs on all components found to be
defective in material or workmanship under normal conditions of
use. This warranty shall not apply to products which have been
abused, modied or disassembled. Products to be repaired under
this warranty must be returned to SnapAV or a designated service
center with prior notication and an assigned return authorization
(RA) number.
For Technical Support call 1.866.838.5052
Lifetime
Tilt Adjustment Lever
(Ratchet)
±5° Horizontal
Adjustment
Tilt Adjustment
Screw
Locking
Tab
Figure 4
Figure 5
Figure 6
Fixed
Tilt
Tilt Arms
Figure 3
Note: Tilt arms shown installed on display.
12° 5°
-
1
-
2
-
3
-
4
Strong SM-CB-F-M Manuel utilisateur
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Strong SM-CB-F-M User manual
